1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
|
// SPDX-License-Identifier: GPL-2.0+
/*
* Serial Device Initialisation for Lasi/Asp/Wax/Dino
*
* (c) Copyright Matthew Wilcox <willy@debian.org> 2001-2002
*/
#include <linux/errno.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
#include <linux/module.h>
#include <linux/serial_core.h>
#include <linux/signal.h>
#include <linux/types.h>
#include <asm/hardware.h>
#include <asm/parisc-device.h>
#include <asm/io.h>
#include "8250.h"
static int __init serial_init_chip(struct parisc_device *dev)
{
struct uart_8250_port uart;
unsigned long address;
int err;
#ifdef CONFIG_64BIT
if (!dev->irq && (dev->id.sversion == 0xad))
dev->irq = iosapic_serial_irq(dev);
#endif
if (!dev->irq) {
/* We find some unattached serial ports by walking native
* busses. These should be silently ignored. Otherwise,
* what we have here is a missing parent device, so tell
* the user what they're missing.
*/
if (parisc_parent(dev)->id.hw_type != HPHW_IOA)
dev_info(&dev->dev,
"Serial: device 0x%llx not configured.\n"
"Enable support for Wax, Lasi, Asp or Dino.\n",
(unsigned long long)dev->hpa.start);
return -ENODEV;
}
address = dev->hpa.start;
if (dev->id.sversion != 0x8d)
address += 0x800;
memset(&uart, 0, sizeof(uart));
uart.port.iotype = UPIO_MEM;
/* 7.272727MHz on Lasi. Assumed the same for Dino, Wax and Timi. */
uart.port.uartclk = (dev->id.sversion != 0xad) ?
7272727 : 1843200;
uart.port.mapbase = address;
uart.port.membase = ioremap_nocache(address, 16);
if (!uart.port.membase) {
dev_warn(&dev->dev, "Failed to map memory\n");
return -ENOMEM;
}
uart.port.irq = dev->irq;
uart.port.flags = UPF_BOOT_AUTOCONF;
uart.port.dev = &dev->dev;
err = serial8250_register_8250_port(&uart);
if (err < 0) {
dev_warn(&dev->dev,
"serial8250_register_8250_port returned error %d\n",
err);
iounmap(uart.port.membase);
return err;
}
return 0;
}
static const struct parisc_device_id serial_tbl[] __initconst = {
{ HPHW_FIO, HVERSION_REV_ANY_ID, HVERSION_ANY_ID, 0x00075 },
{ HPHW_FIO, HVERSION_REV_ANY_ID, HVERSION_ANY_ID, 0x0008c },
{ HPHW_FIO, HVERSION_REV_ANY_ID, HVERSION_ANY_ID, 0x0008d },
{ HPHW_FIO, HVERSION_REV_ANY_ID, HVERSION_ANY_ID, 0x000ad },
{ 0 }
};
/* Hack. Some machines have SERIAL_0 attached to Lasi and SERIAL_1
* attached to Dino. Unfortunately, Dino appears before Lasi in the device
* tree. To ensure that ttyS0 == SERIAL_0, we register two drivers; one
* which only knows about Lasi and then a second which will find all the
* other serial ports. HPUX ignores this problem.
*/
static const struct parisc_device_id lasi_tbl[] __initconst = {
{ HPHW_FIO, HVERSION_REV_ANY_ID, 0x03B, 0x0008C }, /* C1xx/C1xxL */
{ HPHW_FIO, HVERSION_REV_ANY_ID, 0x03C, 0x0008C }, /* B132L */
{ HPHW_FIO, HVERSION_REV_ANY_ID, 0x03D, 0x0008C }, /* B160L */
{ HPHW_FIO, HVERSION_REV_ANY_ID, 0x03E, 0x0008C }, /* B132L+ */
{ HPHW_FIO, HVERSION_REV_ANY_ID, 0x03F, 0x0008C }, /* B180L+ */
{ HPHW_FIO, HVERSION_REV_ANY_ID, 0x046, 0x0008C }, /* Rocky2 120 */
{ HPHW_FIO, HVERSION_REV_ANY_ID, 0x047, 0x0008C }, /* Rocky2 150 */
{ HPHW_FIO, HVERSION_REV_ANY_ID, 0x04E, 0x0008C }, /* Kiji L2 132 */
{ HPHW_FIO, HVERSION_REV_ANY_ID, 0x056, 0x0008C }, /* Raven+ */
{ 0 }
};
MODULE_DEVICE_TABLE(parisc, serial_tbl);
static struct parisc_driver lasi_driver __refdata = {
.name = "serial_1",
.id_table = lasi_tbl,
.probe = serial_init_chip,
};
static struct parisc_driver serial_driver __refdata = {
.name = "serial",
.id_table = serial_tbl,
.probe = serial_init_chip,
};
static int __init probe_serial_gsc(void)
{
register_parisc_driver(&lasi_driver);
register_parisc_driver(&serial_driver);
return 0;
}
module_init(probe_serial_gsc);
MODULE_LICENSE("GPL");
|
