From 731b4cace10f105a81d622b70f9a35f577612d63 Mon Sep 17 00:00:00 2001 From: David George Date: Thu, 2 Jun 2011 08:43:45 -0700 Subject: hwmon: Driver for MAX1668 This patch adds support for MAX1668 and compatible temperature sensors. Signed-off-by: David George [guenter.roeck@ericsson.com: minor cleanup of probe error path] Signed-off-by: Guenter Roeck --- Documentation/hwmon/max1668 | 60 +++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 60 insertions(+) create mode 100644 Documentation/hwmon/max1668 (limited to 'Documentation/hwmon') diff --git a/Documentation/hwmon/max1668 b/Documentation/hwmon/max1668 new file mode 100644 index 000000000000..0616ed9758df --- /dev/null +++ b/Documentation/hwmon/max1668 @@ -0,0 +1,60 @@ +Kernel driver max1668 +===================== + +Supported chips: + * Maxim MAX1668, MAX1805 and MAX1989 + Prefix: 'max1668' + Addresses scanned: I2C 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x4c, 0x4d, 0x4e + Datasheet: http://datasheets.maxim-ic.com/en/ds/MAX1668-MAX1989.pdf + +Author: + David George + +Description +----------- + +This driver implements support for the Maxim MAX1668, MAX1805 and MAX1989 +chips. + +The three devices are very similar, but the MAX1805 has a reduced feature +set; only two remote temperature inputs vs the four avaible on the other +two ICs. + +The driver is able to distinguish between the devices and creates sysfs +entries as follows: + +MAX1805, MAX1668 and MAX1989: + +temp1_input ro local (ambient) temperature +temp1_max rw local temperature maximum threshold for alarm +temp1_max_alarm ro local temperature maximum threshold alarm +temp1_min rw local temperature minimum threshold for alarm +temp1_min_alarm ro local temperature minimum threshold alarm +temp2_input ro remote temperature 1 +temp2_max rw remote temperature 1 maximum threshold for alarm +temp2_max_alarm ro remote temperature 1 maximum threshold alarm +temp2_min rw remote temperature 1 minimum threshold for alarm +temp2_min_alarm ro remote temperature 1 minimum threshold alarm +temp3_input ro remote temperature 2 +temp3_max rw remote temperature 2 maximum threshold for alarm +temp3_max_alarm ro remote temperature 2 maximum threshold alarm +temp3_min rw remote temperature 2 minimum threshold for alarm +temp3_min_alarm ro remote temperature 2 minimum threshold alarm + +MAX1668 and MAX1989 only: +temp4_input ro remote temperature 3 +temp4_max rw remote temperature 3 maximum threshold for alarm +temp4_max_alarm ro remote temperature 3 maximum threshold alarm +temp4_min rw remote temperature 3 minimum threshold for alarm +temp4_min_alarm ro remote temperature 3 minimum threshold alarm +temp5_input ro remote temperature 4 +temp5_max rw remote temperature 4 maximum threshold for alarm +temp5_max_alarm ro remote temperature 4 maximum threshold alarm +temp5_min rw remote temperature 4 minimum threshold for alarm +temp5_min_alarm ro remote temperature 4 minimum threshold alarm + +Module Parameters +----------------- + +* read_only: int + Set to non-zero if you wish to prevent write access to alarm thresholds. -- cgit v1.2.1 From f22aaaa70d8c24e5dc7d23a219c4beace8354b65 Mon Sep 17 00:00:00 2001 From: Donggeun Kim Date: Mon, 20 Jun 2011 16:48:19 +0900 Subject: hwmon: Driver for NTC Thermistors Add support for NTC Thermistor series. In this release, the following thermistors are supported: NCP15WB473, NCP18WB473, NCP03WB473, and NCP15WL333. This driver is based on the datasheet of MURATA. The driver in the patch does conversion from the raw ADC value (either voltage or resistence) to temperature. In order to use voltage values as input, the circuit schematics should be provided with the platform data. A compensation table for each type of thermistor is provided for the conversion. Signed-off-by: Donggeun Kim Signed-off-by: MyungJoo Ham Signed-off-by: KyungMin Park Reviewed-by: Shubhrajyoti D Signed-off-by: Guenter Roeck --- Documentation/hwmon/ntc_thermistor | 93 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 93 insertions(+) create mode 100644 Documentation/hwmon/ntc_thermistor (limited to 'Documentation/hwmon') diff --git a/Documentation/hwmon/ntc_thermistor b/Documentation/hwmon/ntc_thermistor new file mode 100644 index 000000000000..3bfda94096fd --- /dev/null +++ b/Documentation/hwmon/ntc_thermistor @@ -0,0 +1,93 @@ +Kernel driver ntc_thermistor +================= + +Supported thermistors: +* Murata NTC Thermistors NCP15WB473, NCP18WB473, NCP21WB473, NCP03WB473, NCP15WL333 + Prefixes: 'ncp15wb473', 'ncp18wb473', 'ncp21wb473', 'ncp03wb473', 'ncp15wl333' + Datasheet: Publicly available at Murata + +Other NTC thermistors can be supported simply by adding compensation +tables; e.g., NCP15WL333 support is added by the table ncpXXwl333. + +Authors: + MyungJoo Ham + +Description +----------- + +The NTC thermistor is a simple thermistor that requires users to provide the +resistance and lookup the corresponding compensation table to get the +temperature input. + +The NTC driver provides lookup tables with a linear approximation function +and four circuit models with an option not to use any of the four models. + +The four circuit models provided are: + + $: resister, [TH]: the thermistor + + 1. connect = NTC_CONNECTED_POSITIVE, pullup_ohm > 0 + + [pullup_uV] + | | + [TH] $ (pullup_ohm) + | | + +----+-----------------------[read_uV] + | + $ (pulldown_ohm) + | + --- (ground) + + 2. connect = NTC_CONNECTED_POSITIVE, pullup_ohm = 0 (not-connected) + + [pullup_uV] + | + [TH] + | + +----------------------------[read_uV] + | + $ (pulldown_ohm) + | + --- (ground) + + 3. connect = NTC_CONNECTED_GROUND, pulldown_ohm > 0 + + [pullup_uV] + | + $ (pullup_ohm) + | + +----+-----------------------[read_uV] + | | + [TH] $ (pulldown_ohm) + | | + -------- (ground) + + 4. connect = NTC_CONNECTED_GROUND, pulldown_ohm = 0 (not-connected) + + [pullup_uV] + | + $ (pullup_ohm) + | + +----------------------------[read_uV] + | + [TH] + | + --- (ground) + +When one of the four circuit models is used, read_uV, pullup_uV, pullup_ohm, +pulldown_ohm, and connect should be provided. When none of the four models +are suitable or the user can get the resistance directly, the user should +provide read_ohm and _not_ provide the others. + +Sysfs Interface +--------------- +name the mandatory global attribute, the thermistor name. + +temp1_type always 4 (thermistor) + RO + +temp1_input measure the temperature and provide the measured value. + (reading this file initiates the reading procedure.) + RO + +Note that each NTC thermistor has only _one_ thermistor; thus, only temp1 exists. -- cgit v1.2.1 From 2ef017935d698b1c7c7421a7ebe20579d8f904dd Mon Sep 17 00:00:00 2001 From: Stijn Devriendt Date: Mon, 6 Jun 2011 10:40:45 +0000 Subject: hwmon: (lm90) Add support for Philips SA56004 Add support for Philips SA56004, an LM86 compatible temperature sensor. Signed-off-by: Stijn Devriendt Signed-off-by: Guenter Roeck --- Documentation/hwmon/lm90 | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) (limited to 'Documentation/hwmon') diff --git a/Documentation/hwmon/lm90 b/Documentation/hwmon/lm90 index f3efd18e87f4..9cd14cfe6515 100644 --- a/Documentation/hwmon/lm90 +++ b/Documentation/hwmon/lm90 @@ -113,7 +113,11 @@ Supported chips: Prefix: 'w83l771' Addresses scanned: I2C 0x4c Datasheet: Not publicly available, can be requested from Nuvoton - + * Philips/NXP SA56004X + Prefix: 'sa56004' + Addresses scanned: I2C 0x48 through 0x4F + Datasheet: Publicly available at NXP website + http://ics.nxp.com/products/interface/datasheet/sa56004x.pdf Author: Jean Delvare @@ -193,6 +197,9 @@ W83L771AWG/ASG * The AWG and ASG variants only differ in package format. * Diode ideality factor configuration (remote sensor) at 0xE3 +SA56004X: + * Better local resolution + All temperature values are given in degrees Celsius. Resolution is 1.0 degree for the local temperature, 0.125 degree for the remote temperature, except for the MAX6657, MAX6658 and MAX6659 which have a -- cgit v1.2.1 From fffd80ccc1e6c7e5f13741e17a7d80582ae21fcc Mon Sep 17 00:00:00 2001 From: Alexander Stein Date: Tue, 28 Jun 2011 15:11:23 +0000 Subject: hwmon: LM95245 driver A hwmon driver for the National Semiconductor LM95245 dual temperature sensors chip. Signed-off-by: Alexander Stein Signed-off-by: Guenter Roeck --- Documentation/hwmon/lm95245 | 33 +++++++++++++++++++++++++++++++++ 1 file changed, 33 insertions(+) create mode 100644 Documentation/hwmon/lm95245 (limited to 'Documentation/hwmon') diff --git a/Documentation/hwmon/lm95245 b/Documentation/hwmon/lm95245 new file mode 100644 index 000000000000..cbd8aeab7124 --- /dev/null +++ b/Documentation/hwmon/lm95245 @@ -0,0 +1,33 @@ +Kernel driver lm95245 +================== + +Supported chips: + * National Semiconductor LM95245 + Addresses scanned: I2C 0x18, 0x19, 0x29, 0x4c, 0x4d + Datasheet: Publicly available at the National Semiconductor website + http://www.national.com/mpf/LM/LM95245.html + + +Author: Alexander Stein + +Description +----------- + +The LM95245 is an 11-bit digital temperature sensor with a 2-wire System +Management Bus (SMBus) interface and TruTherm technology that can monitor +the temperature of a remote diode as well as its own temperature. +The LM95245 can be used to very accurately monitor the temperature of +external devices such as microprocessors. + +All temperature values are given in millidegrees Celsius. Local temperature +is given within a range of -127 to +127.875 degrees. Remote temperatures are +given within a range of -127 to +255 degrees. Resolution depends on +temperature input and range. + +Each sensor has its own critical limit, but the hysteresis is common to all +two channels. + +The lm95245 driver can change its update interval to a fixed set of values. +It will round up to the next selectable interval. See the datasheet for exact +values. Reading sensor values more often will do no harm, but will return +'old' values. -- cgit v1.2.1 From c814a4c7c4aad795835583344353963a0a673eb0 Mon Sep 17 00:00:00 2001 From: Durgadoss R Date: Tue, 12 Jul 2011 07:07:16 -0400 Subject: hwmon: (coretemp) Add core/pkg threshold support to Coretemp This patch adds the core and pkg support to coretemp. These thresholds can be configured via the sysfs interfaces tempX_max and tempX_max_hyst. An interrupt is generated when CPU temperature reaches or crosses above tempX_max OR drops below tempX_max_hyst. This patch is based on the documentation in IA Manual vol 3A, that can be downloaded from here: http://download.intel.com/design/processor/manuals/253668.pdf Signed-off-by: Durgadoss R Signed-off-by: Guenter Roeck --- Documentation/hwmon/coretemp | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'Documentation/hwmon') diff --git a/Documentation/hwmon/coretemp b/Documentation/hwmon/coretemp index f85e913a3401..fa8776ab9b18 100644 --- a/Documentation/hwmon/coretemp +++ b/Documentation/hwmon/coretemp @@ -35,6 +35,13 @@ the Out-Of-Spec bit. Following table summarizes the exported sysfs files: All Sysfs entries are named with their core_id (represented here by 'X'). tempX_input - Core temperature (in millidegrees Celsius). tempX_max - All cooling devices should be turned on (on Core2). + Initialized with IA32_THERM_INTERRUPT. When the CPU + temperature reaches this temperature, an interrupt is + generated and tempX_max_alarm is set. +tempX_max_hyst - If the CPU temperature falls below than temperature, + an interrupt is generated and tempX_max_alarm is reset. +tempX_max_alarm - Set if the temperature reaches or exceeds tempX_max. + Reset if the temperature drops to or below tempX_max_hyst. tempX_crit - Maximum junction temperature (in millidegrees Celsius). tempX_crit_alarm - Set when Out-of-spec bit is set, never clears. Correct CPU operation is no longer guaranteed. -- cgit v1.2.1 From e0455e380b5bdf8dff7c8e29423d2446d9f59040 Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Sat, 25 Jun 2011 15:13:44 -0700 Subject: hwmon: (pmbus) Add ADP4000, NCP4200 and NCP4208 to list of supported devices Add ADP4000, NCP4200 and NCP4208 to the list of devices supported by the generic PMBus driver, and add device IDs to enable explicit instantiation. Signed-off-by: Guenter Roeck Reviewed-by: Robert Coulson Acked-by: Jean Delvare --- Documentation/hwmon/pmbus | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'Documentation/hwmon') diff --git a/Documentation/hwmon/pmbus b/Documentation/hwmon/pmbus index 5e462fc7f99b..c36c1c1a62bb 100644 --- a/Documentation/hwmon/pmbus +++ b/Documentation/hwmon/pmbus @@ -13,6 +13,13 @@ Supported chips: Prefix: 'ltc2978' Addresses scanned: - Datasheet: http://cds.linear.com/docs/Datasheet/2978fa.pdf + * ON Semiconductor ADP4000, NCP4200, NCP4208 + Prefixes: 'adp4000', 'ncp4200', 'ncp4208' + Addresses scanned: - + Datasheets: + http://www.onsemi.com/pub_link/Collateral/ADP4000-D.PDF + http://www.onsemi.com/pub_link/Collateral/NCP4200-D.PDF + http://www.onsemi.com/pub_link/Collateral/JUNE%202009-%20REV.%200.PDF * Generic PMBus devices Prefix: 'pmbus' Addresses scanned: - -- cgit v1.2.1 From 0084e9faabbc1e228fda9c8a78ef1ea8ee97a9ae Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Sat, 9 Jul 2011 10:32:11 -0700 Subject: hwmon: Add new attributes to sysfs ABI Add the following attributes to the sysfs ABI. in[0-*]_average in[0-*]_lowest in[0-*]_highest in[0-*]_reset_history in_reset_history curr[1-*]_average curr[1-*]_lowest curr[1-*]_highest curr[1-*]_reset_history curr_reset_history Signed-off-by: Guenter Roeck Reviewed-by: Robert Coulson --- Documentation/hwmon/sysfs-interface | 46 +++++++++++++++++++++++++++++++++++++ 1 file changed, 46 insertions(+) (limited to 'Documentation/hwmon') diff --git a/Documentation/hwmon/sysfs-interface b/Documentation/hwmon/sysfs-interface index 8f63c244f1aa..a4aa8f600e09 100644 --- a/Documentation/hwmon/sysfs-interface +++ b/Documentation/hwmon/sysfs-interface @@ -139,6 +139,29 @@ in[0-*]_input Voltage input value. thumb: drivers should report the voltage values at the "pins" of the chip. +in[0-*]_average + Average voltage + Unit: millivolt + RO + +in[0-*]_lowest + Historical minimum voltage + Unit: millivolt + RO + +in[0-*]_highest + Historical maximum voltage + Unit: millivolt + RO + +in[0-*]_reset_history + Reset inX_lowest and inX_highest + WO + +in_reset_history + Reset inX_lowest and inX_highest for all sensors + WO + in[0-*]_label Suggested voltage channel label. Text string Should only be created if the driver has hints about what @@ -407,6 +430,29 @@ curr[1-*]_input Current input value Unit: milliampere RO +curr[1-*]_average + Average current use + Unit: milliampere + RO + +curr[1-*]_lowest + Historical minimum current + Unit: milliampere + RO + +curr[1-*]_highest + Historical maximum current + Unit: milliampere + RO + +curr[1-*]_reset_history + Reset currX_lowest and currX_highest + WO + +curr_reset_history + Reset currX_lowest and currX_highest for all sensors + WO + Also see the Alarms section for status flags associated with currents. ********* -- cgit v1.2.1 From c576e30cd0c9814b3b45772d46924d796f538dee Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Sat, 9 Jul 2011 11:17:33 -0700 Subject: hwmon: (adm1275) Add support for peak attributes Add support for voltage and current peak (historic maximum) attributes. Signed-off-by: Guenter Roeck Reviewed-by: Robert Coulson --- Documentation/hwmon/adm1275 | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) (limited to 'Documentation/hwmon') diff --git a/Documentation/hwmon/adm1275 b/Documentation/hwmon/adm1275 index 6a3a6476cf20..097b3ccc4be7 100644 --- a/Documentation/hwmon/adm1275 +++ b/Documentation/hwmon/adm1275 @@ -43,8 +43,8 @@ Documentation/hwmon/pmbus for details. Sysfs entries ------------- -The following attributes are supported. Limits are read-write; all other -attributes are read-only. +The following attributes are supported. Limits are read-write, history reset +attributes are write-only, all other attributes are read-only. in1_label "vin1" or "vout1" depending on chip variant and configuration. @@ -53,8 +53,12 @@ in1_min Minumum Voltage. From VOUT_UV_WARN_LIMIT register. in1_max Maximum voltage. From VOUT_OV_WARN_LIMIT register. in1_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. in1_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. +in1_highest Historical maximum voltage. +in1_reset_history Write any value to reset history. curr1_label "iout1" curr1_input Measured current. From READ_IOUT register. curr1_max Maximum current. From IOUT_OC_WARN_LIMIT register. curr1_max_alarm Current high alarm. From IOUT_OC_WARN_LIMIT register. +curr1_highest Historical maximum current. +curr1_reset_history Write any value to reset history. -- cgit v1.2.1 From 8ebed854506301f4f67e75c73cae967d4a45ab4d Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Sat, 9 Jul 2011 13:10:19 -0700 Subject: hwmon: (max16064) Add support for peak attributes Add support for voltage and temperature peak (historic maximum) attributes. Signed-off-by: Guenter Roeck Reviewed-by: Robert Coulson --- Documentation/hwmon/max16064 | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'Documentation/hwmon') diff --git a/Documentation/hwmon/max16064 b/Documentation/hwmon/max16064 index 41728999e142..f6e8bcbfaccf 100644 --- a/Documentation/hwmon/max16064 +++ b/Documentation/hwmon/max16064 @@ -50,6 +50,8 @@ in[1-4]_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. in[1-4]_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. in[1-4]_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT status. in[1-4]_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT status. +in[1-4]_highest Historical maximum voltage. +in[1-4]_reset_history Write any value to reset history. temp1_input Measured temperature. From READ_TEMPERATURE_1 register. temp1_max Maximum temperature. From OT_WARN_LIMIT register. @@ -60,3 +62,5 @@ temp1_max_alarm Chip temperature high alarm. Set by comparing temp1_crit_alarm Chip temperature critical high alarm. Set by comparing READ_TEMPERATURE_1 with OT_FAULT_LIMIT if TEMP_OT_FAULT status is set. +temp1_highest Historical maximum temperature. +temp1_reset_history Write any value to reset history. -- cgit v1.2.1 From 70e94b276c21638a0a37908f6696a6b122944dea Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Sat, 9 Jul 2011 13:11:44 -0700 Subject: hwmon: (max8688) Add support for peak attributes Add support for voltage, current, and temperature peak (historic maximum) attributes. Signed-off-by: Guenter Roeck --- Documentation/hwmon/max8688 | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'Documentation/hwmon') diff --git a/Documentation/hwmon/max8688 b/Documentation/hwmon/max8688 index 0ddd3a412030..71ed10a3c94e 100644 --- a/Documentation/hwmon/max8688 +++ b/Documentation/hwmon/max8688 @@ -50,6 +50,8 @@ in1_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. in1_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. in1_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT status. in1_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT status. +in1_highest Historical maximum voltage. +in1_reset_history Write any value to reset history. curr1_label "iout1" curr1_input Measured current. From READ_IOUT register. @@ -57,6 +59,8 @@ curr1_max Maximum current. From IOUT_OC_WARN_LIMIT register. curr1_crit Critical maximum current. From IOUT_OC_FAULT_LIMIT register. curr1_max_alarm Current high alarm. From IOUT_OC_WARN_LIMIT register. curr1_crit_alarm Current critical high alarm. From IOUT_OC_FAULT status. +curr1_highest Historical maximum current. +curr1_reset_history Write any value to reset history. temp1_input Measured temperature. From READ_TEMPERATURE_1 register. temp1_max Maximum temperature. From OT_WARN_LIMIT register. @@ -67,3 +71,5 @@ temp1_max_alarm Chip temperature high alarm. Set by comparing temp1_crit_alarm Chip temperature critical high alarm. Set by comparing READ_TEMPERATURE_1 with OT_FAULT_LIMIT if TEMP_OT_FAULT status is set. +temp1_highest Historical maximum temperature. +temp1_reset_history Write any value to reset history. -- cgit v1.2.1 From 98591dbe633eace43a20ffa2907861fbef97237b Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Sat, 9 Jul 2011 13:17:43 -0700 Subject: hwmon: (max34440) Add support for peak attributes Add support for voltage, current, and temperature peak (historic maximum) attributes. Signed-off-by: Guenter Roeck Reviewed-by: Robert Coulson --- Documentation/hwmon/max34440 | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'Documentation/hwmon') diff --git a/Documentation/hwmon/max34440 b/Documentation/hwmon/max34440 index 6c525dd07d59..8ab51536a1eb 100644 --- a/Documentation/hwmon/max34440 +++ b/Documentation/hwmon/max34440 @@ -56,6 +56,8 @@ in[1-6]_min_alarm Voltage low alarm. From VOLTAGE_UV_WARNING status. in[1-6]_max_alarm Voltage high alarm. From VOLTAGE_OV_WARNING status. in[1-6]_lcrit_alarm Voltage critical low alarm. From VOLTAGE_UV_FAULT status. in[1-6]_crit_alarm Voltage critical high alarm. From VOLTAGE_OV_FAULT status. +in[1-6]_highest Historical maximum voltage. +in[1-6]_reset_history Write any value to reset history. curr[1-6]_label "iout[1-6]". curr[1-6]_input Measured current. From READ_IOUT register. @@ -63,6 +65,8 @@ curr[1-6]_max Maximum current. From IOUT_OC_WARN_LIMIT register. curr[1-6]_crit Critical maximum current. From IOUT_OC_FAULT_LIMIT register. curr[1-6]_max_alarm Current high alarm. From IOUT_OC_WARNING status. curr[1-6]_crit_alarm Current critical high alarm. From IOUT_OC_FAULT status. +curr[1-6]_highest Historical maximum current. +curr[1-6]_reset_history Write any value to reset history. in6 and curr6 attributes only exist for MAX34440. @@ -75,5 +79,7 @@ temp[1-8]_max Maximum temperature. From OT_WARN_LIMIT register. temp[1-8]_crit Critical high temperature. From OT_FAULT_LIMIT register. temp[1-8]_max_alarm Temperature high alarm. temp[1-8]_crit_alarm Temperature critical high alarm. +temp[1-8]_highest Historical maximum temperature. +temp[1-8]_reset_history Write any value to reset history. temp7 and temp8 attributes only exist for MAX34440. -- cgit v1.2.1 From 03e9bd8dbcee60c2e22fd54f9f28f0d32da218c3 Mon Sep 17 00:00:00 2001 From: Guenter Roeck Date: Fri, 8 Jul 2011 10:43:57 -0700 Subject: hwmon: (pmbus) Add client driver for LM25066, LM5064, and LM5066 PMBus client driver supporting National Semiconductor LM25066, LM5064, and LM5066. Signed-off-by: Guenter Roeck Reviewed-by: Robert Coulson --- Documentation/hwmon/lm25066 | 90 +++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 90 insertions(+) create mode 100644 Documentation/hwmon/lm25066 (limited to 'Documentation/hwmon') diff --git a/Documentation/hwmon/lm25066 b/Documentation/hwmon/lm25066 new file mode 100644 index 000000000000..a21db81c4591 --- /dev/null +++ b/Documentation/hwmon/lm25066 @@ -0,0 +1,90 @@ +Kernel driver max8688 +===================== + +Supported chips: + * National Semiconductor LM25066 + Prefix: 'lm25066' + Addresses scanned: - + Datasheets: + http://www.national.com/pf/LM/LM25066.html + http://www.national.com/pf/LM/LM25066A.html + * National Semiconductor LM5064 + Prefix: 'lm5064' + Addresses scanned: - + Datasheet: + http://www.national.com/pf/LM/LM5064.html + * National Semiconductor LM5066 + Prefix: 'lm5066' + Addresses scanned: - + Datasheet: + http://www.national.com/pf/LM/LM5066.html + +Author: Guenter Roeck + + +Description +----------- + +This driver supports hardware montoring for National Semiconductor LM25066, +LM5064, and LM5064 Power Management, Monitoring, Control, and Protection ICs. + +The driver is a client driver to the core PMBus driver. Please see +Documentation/hwmon/pmbus for details on PMBus client drivers. + + +Usage Notes +----------- + +This driver does not auto-detect devices. You will have to instantiate the +devices explicitly. Please see Documentation/i2c/instantiating-devices for +details. + + +Platform data support +--------------------- + +The driver supports standard PMBus driver platform data. + + +Sysfs entries +------------- + +The following attributes are supported. Limits are read-write; all other +attributes are read-only. + +in1_label "vin" +in1_input Measured input voltage. +in1_average Average measured input voltage. +in1_min Minimum input voltage. +in1_max Maximum input voltage. +in1_min_alarm Input voltage low alarm. +in1_max_alarm Input voltage high alarm. + +in2_label "vout1" +in2_input Measured output voltage. +in2_average Average measured output voltage. +in2_min Minimum output voltage. +in2_min_alarm Output voltage low alarm. + +in3_label "vout2" +in3_input Measured voltage on vaux pin + +curr1_label "iin" +curr1_input Measured input current. +curr1_average Average measured input current. +curr1_max Maximum input current. +curr1_max_alarm Input current high alarm. + +power1_label "pin" +power1_input Measured input power. +power1_average Average measured input power. +power1_max Maximum input power limit. +power1_alarm Input power alarm +power1_input_highest Historical maximum power. +power1_reset_history Write any value to reset maximum power history. + +temp1_input Measured temperature. +temp1_max Maximum temperature. +temp1_crit Critical high temperature. +temp1_max_alarm Chip temperature high alarm. +temp1_crit_alarm Chip temperature critical high alarm. -- cgit v1.2.1