From d324d4627d7442d9a74b0b93fc40f71ce194632a Mon Sep 17 00:00:00 2001 From: Mikael Pettersson Date: Wed, 6 Dec 2006 09:55:43 +0100 Subject: [PATCH] sata_promise: cleanups, take 2 This patch performs two simple cleanups of sata_promise. * Remove board_20771 and map device id 0x3577 to board_2057x. After the recent corrections for SATAII chips, board_20771 and board_2057x were equivalent in the driver. * Remove hp->hotplug_offset and use hp->flags & PDC_FLAG_GEN_II to compute hotplug_offset in pdc_host_init(). hp->hotplug_offset was used to distinguish 1st and 2nd generation chips in one particular case, but now we have that information in a more general form in hp->flags, so hp->hotplug_offset is redundant. Changes since previous submission: rebased on libata-dev #upstream, cleaned up hotplug_offset computation based on Tejun's comments, expanded hotplug_offset removal rationale. This patch does not depend on the pending new EH conversion patch. Signed-off-by: Mikael Pettersson Signed-off-by: Jeff Garzik --- drivers/ata/sata_promise.c | 40 +++++++++------------------------------- 1 file changed, 9 insertions(+), 31 deletions(-) diff --git a/drivers/ata/sata_promise.c b/drivers/ata/sata_promise.c index a2778cf016bc..6f7bc5b0ef4a 100644 --- a/drivers/ata/sata_promise.c +++ b/drivers/ata/sata_promise.c @@ -66,9 +66,8 @@ enum { board_2037x = 0, /* FastTrak S150 TX2plus */ board_20319 = 1, /* FastTrak S150 TX4 */ board_20619 = 2, /* FastTrak TX4000 */ - board_20771 = 3, /* FastTrak TX2300 */ - board_2057x = 4, /* SATAII150 Tx2plus */ - board_40518 = 5, /* SATAII150 Tx4 */ + board_2057x = 3, /* SATAII150 Tx2plus */ + board_40518 = 4, /* SATAII150 Tx4 */ PDC_HAS_PATA = (1 << 1), /* PDC20375/20575 has PATA */ @@ -90,7 +89,6 @@ struct pdc_port_priv { struct pdc_host_priv { unsigned long flags; - int hotplug_offset; }; static u32 pdc_sata_scr_read (struct ata_port *ap, unsigned int sc_reg); @@ -205,16 +203,6 @@ static const struct ata_port_info pdc_port_info[] = { .port_ops = &pdc_pata_ops, }, - /* board_20771 */ - { - .sht = &pdc_ata_sht, - .flags = PDC_COMMON_FLAGS | ATA_FLAG_SATA, - .pio_mask = 0x1f, /* pio0-4 */ - .mwdma_mask = 0x07, /* mwdma0-2 */ - .udma_mask = 0x7f, /* udma0-6 ; FIXME */ - .port_ops = &pdc_sata_ops, - }, - /* board_2057x */ { .sht = &pdc_ata_sht, @@ -244,6 +232,7 @@ static const struct pci_device_id pdc_ata_pci_tbl[] = { { PCI_VDEVICE(PROMISE, 0x3570), board_2057x }, { PCI_VDEVICE(PROMISE, 0x3571), board_2057x }, { PCI_VDEVICE(PROMISE, 0x3574), board_2057x }, + { PCI_VDEVICE(PROMISE, 0x3577), board_2057x }, { PCI_VDEVICE(PROMISE, 0x3d73), board_2057x }, { PCI_VDEVICE(PROMISE, 0x3d75), board_2057x }, @@ -256,15 +245,6 @@ static const struct pci_device_id pdc_ata_pci_tbl[] = { { PCI_VDEVICE(PROMISE, 0x6629), board_20619 }, -/* TODO: remove all associated board_20771 code, as it completely - * duplicates board_2037x code, unless reason for separation can be - * divined. - */ -#if 0 - { PCI_VDEVICE(PROMISE, 0x3570), board_20771 }, -#endif - { PCI_VDEVICE(PROMISE, 0x3577), board_20771 }, - { } /* terminate list */ }; @@ -645,9 +625,14 @@ static void pdc_host_init(unsigned int chip_id, struct ata_probe_ent *pe) { void __iomem *mmio = pe->mmio_base; struct pdc_host_priv *hp = pe->private_data; - int hotplug_offset = hp->hotplug_offset; + int hotplug_offset; u32 tmp; + if (hp->flags & PDC_FLAG_GEN_II) + hotplug_offset = PDC2_SATA_PLUG_CSR; + else + hotplug_offset = PDC_SATA_PLUG_CSR; + /* * Except for the hotplug stuff, this is voodoo from the * Promise driver. Label this entire section @@ -742,8 +727,6 @@ static int pdc_ata_init_one (struct pci_dev *pdev, const struct pci_device_id *e goto err_out_free_ent; } - /* Set default hotplug offset */ - hp->hotplug_offset = PDC_SATA_PLUG_CSR; probe_ent->private_data = hp; probe_ent->sht = pdc_port_info[board_idx].sht; @@ -767,8 +750,6 @@ static int pdc_ata_init_one (struct pci_dev *pdev, const struct pci_device_id *e switch (board_idx) { case board_40518: hp->flags |= PDC_FLAG_GEN_II; - /* Override hotplug offset for SATAII150 */ - hp->hotplug_offset = PDC2_SATA_PLUG_CSR; /* Fall through */ case board_20319: probe_ent->n_ports = 4; @@ -780,10 +761,7 @@ static int pdc_ata_init_one (struct pci_dev *pdev, const struct pci_device_id *e probe_ent->port[3].scr_addr = base + 0x700; break; case board_2057x: - case board_20771: hp->flags |= PDC_FLAG_GEN_II; - /* Override hotplug offset for SATAII150 */ - hp->hotplug_offset = PDC2_SATA_PLUG_CSR; /* Fall through */ case board_2037x: probe_ent->n_ports = 2; -- cgit v1.2.1 From e3472cbe5c10a91c737405cd706142787736392c Mon Sep 17 00:00:00 2001 From: Albert Lee Date: Thu, 7 Dec 2006 11:37:58 +0800 Subject: [PATCH] libata: let ATA_FLAG_PIO_POLLING use polling pio for ATA_PROT_NODATA Even if ATA_FLAG_PIO_POLLING is set, libata uses irq pio for the ATA_PROT_NODATA protocol. This patch let ATA_FLAG_PIO_POLLING use polling pio for the ATA_PROT_NODATA protocol. Signed-off-by: Albert Lee Signed-off-by: Jeff Garzik --- drivers/ata/libata-core.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index 8816e30fb7a4..d2e686371870 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -4960,6 +4960,7 @@ unsigned int ata_qc_issue_prot(struct ata_queued_cmd *qc) if (ap->flags & ATA_FLAG_PIO_POLLING) { switch (qc->tf.protocol) { case ATA_PROT_PIO: + case ATA_PROT_NODATA: case ATA_PROT_ATAPI: case ATA_PROT_ATAPI_NODATA: qc->tf.flags |= ATA_TFLAG_POLLING; -- cgit v1.2.1 From 25b93d81b9abe3b786bdf3396d728bb13b0a911c Mon Sep 17 00:00:00 2001 From: Mikael Pettersson Date: Thu, 7 Dec 2006 00:06:51 +0100 Subject: [PATCH] sata_promise: new EH conversion, take 2 This patch converts sata_promise to use new-style libata error handling on Promise SATA chips, for both SATA and PATA ports. * ATA_FLAG_SRST is no longer set * ->phy_reset is no longer set as it is unused when ->error_handler is present, and pdc_sata_phy_reset() has been removed * pdc_freeze() masks interrupts and halts DMA via PDC_CTLSTAT * pdc_thaw() clears interrupt status in PDC_INT_SEQMASK and then unmasks interrupts in PDC_CTLSTAT * pdc_error_handler() reinitialises the port if it isn't frozen, and then invokes ata_do_eh() with standard {s,}ata reset methods * pdc_post_internal_cmd() resets the port in case of errors * the PATA-only 20619 chip continues to use old-style EH: not by necessity but simply because I don't have documentation for it or any way to test it Since the previous version pdc_error_handler() has been rewritten and it now mostly matches ahci and sata_sil24. In case anyone wonders: the call to pdc_reset_port() isn't a heavy-duty reset, it's a light-weight reset to quickly put a port into a sane state. The discussion about the PCI flushes in pdc_freeze() and pdc_thaw() seemed to end with a consensus that the flushes are OK and not obviously redundant, so I decided to keep them for now. This patch was prepared against 2.6.19-git7, but it also applies to 2.6.19 + libata #upstream, with or without the revised sata_promise cleanup patch I recently submitted. This patch does conflict with the #promise-sata-pata patch: this patch removes pdc_sata_phy_reset() while #promise-sata-pata modifies it. The correct patch resolution is to remove the function. Tested on 2037x and 2057x chips, with PATA patches on top and disks on both SATA and PATA ports. Signed-off-by: Mikael Pettersson Signed-off-by: Jeff Garzik --- drivers/ata/sata_promise.c | 80 +++++++++++++++++++++++++++++++++++++++------- 1 file changed, 68 insertions(+), 12 deletions(-) diff --git a/drivers/ata/sata_promise.c b/drivers/ata/sata_promise.c index 6f7bc5b0ef4a..f055874a6ec5 100644 --- a/drivers/ata/sata_promise.c +++ b/drivers/ata/sata_promise.c @@ -71,9 +71,12 @@ enum { PDC_HAS_PATA = (1 << 1), /* PDC20375/20575 has PATA */ + /* PDC_CTLSTAT bit definitions */ + PDC_DMA_ENABLE = (1 << 7), + PDC_IRQ_DISABLE = (1 << 10), PDC_RESET = (1 << 11), /* HDMA reset */ - PDC_COMMON_FLAGS = ATA_FLAG_NO_LEGACY | ATA_FLAG_SRST | + PDC_COMMON_FLAGS = ATA_FLAG_NO_LEGACY | ATA_FLAG_MMIO | ATA_FLAG_NO_ATAPI | ATA_FLAG_PIO_POLLING, @@ -99,13 +102,16 @@ static void pdc_eng_timeout(struct ata_port *ap); static int pdc_port_start(struct ata_port *ap); static void pdc_port_stop(struct ata_port *ap); static void pdc_pata_phy_reset(struct ata_port *ap); -static void pdc_sata_phy_reset(struct ata_port *ap); static void pdc_qc_prep(struct ata_queued_cmd *qc); static void pdc_tf_load_mmio(struct ata_port *ap, const struct ata_taskfile *tf); static void pdc_exec_command_mmio(struct ata_port *ap, const struct ata_taskfile *tf); static void pdc_irq_clear(struct ata_port *ap); static unsigned int pdc_qc_issue_prot(struct ata_queued_cmd *qc); static void pdc_host_stop(struct ata_host *host); +static void pdc_freeze(struct ata_port *ap); +static void pdc_thaw(struct ata_port *ap); +static void pdc_error_handler(struct ata_port *ap); +static void pdc_post_internal_cmd(struct ata_queued_cmd *qc); static struct scsi_host_template pdc_ata_sht = { @@ -134,11 +140,12 @@ static const struct ata_port_operations pdc_sata_ops = { .exec_command = pdc_exec_command_mmio, .dev_select = ata_std_dev_select, - .phy_reset = pdc_sata_phy_reset, - .qc_prep = pdc_qc_prep, .qc_issue = pdc_qc_issue_prot, - .eng_timeout = pdc_eng_timeout, + .freeze = pdc_freeze, + .thaw = pdc_thaw, + .error_handler = pdc_error_handler, + .post_internal_cmd = pdc_post_internal_cmd, .data_xfer = ata_mmio_data_xfer, .irq_handler = pdc_interrupt, .irq_clear = pdc_irq_clear, @@ -196,7 +203,7 @@ static const struct ata_port_info pdc_port_info[] = { /* board_20619 */ { .sht = &pdc_ata_sht, - .flags = PDC_COMMON_FLAGS | ATA_FLAG_SLAVE_POSS, + .flags = PDC_COMMON_FLAGS | ATA_FLAG_SRST | ATA_FLAG_SLAVE_POSS, .pio_mask = 0x1f, /* pio0-4 */ .mwdma_mask = 0x07, /* mwdma0-2 */ .udma_mask = 0x7f, /* udma0-6 ; FIXME */ @@ -346,12 +353,6 @@ static void pdc_reset_port(struct ata_port *ap) readl(mmio); /* flush */ } -static void pdc_sata_phy_reset(struct ata_port *ap) -{ - pdc_reset_port(ap); - sata_phy_reset(ap); -} - static void pdc_pata_cbl_detect(struct ata_port *ap) { u8 tmp; @@ -419,6 +420,61 @@ static void pdc_qc_prep(struct ata_queued_cmd *qc) } } +static void pdc_freeze(struct ata_port *ap) +{ + void __iomem *mmio = (void __iomem *) ap->ioaddr.cmd_addr; + u32 tmp; + + tmp = readl(mmio + PDC_CTLSTAT); + tmp |= PDC_IRQ_DISABLE; + tmp &= ~PDC_DMA_ENABLE; + writel(tmp, mmio + PDC_CTLSTAT); + readl(mmio + PDC_CTLSTAT); /* flush */ +} + +static void pdc_thaw(struct ata_port *ap) +{ + void __iomem *mmio = (void __iomem *) ap->ioaddr.cmd_addr; + u32 tmp; + + /* clear IRQ */ + readl(mmio + PDC_INT_SEQMASK); + + /* turn IRQ back on */ + tmp = readl(mmio + PDC_CTLSTAT); + tmp &= ~PDC_IRQ_DISABLE; + writel(tmp, mmio + PDC_CTLSTAT); + readl(mmio + PDC_CTLSTAT); /* flush */ +} + +static void pdc_error_handler(struct ata_port *ap) +{ + ata_reset_fn_t hardreset; + + if (!(ap->pflags & ATA_PFLAG_FROZEN)) + pdc_reset_port(ap); + + hardreset = NULL; + if (sata_scr_valid(ap)) + hardreset = sata_std_hardreset; + + /* perform recovery */ + ata_do_eh(ap, ata_std_prereset, ata_std_softreset, hardreset, + ata_std_postreset); +} + +static void pdc_post_internal_cmd(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + + if (qc->flags & ATA_QCFLAG_FAILED) + qc->err_mask |= AC_ERR_OTHER; + + /* make DMA engine forget about the failed command */ + if (qc->err_mask) + pdc_reset_port(ap); +} + static void pdc_eng_timeout(struct ata_port *ap) { struct ata_host *host = ap->host; -- cgit v1.2.1 From fd3367af3d1212f645094c4b5c4d458bdd061475 Mon Sep 17 00:00:00 2001 From: Alan Date: Thu, 7 Dec 2006 12:41:18 +0000 Subject: [PATCH] libata: Incorrect timing computation for PIO5/6 The ata timing computation code makes some mistakes in PIO5/6 because a check was not updated correctly when I put this support into the kernel. Signed-off-by: Alan Cox Signed-off-by: Jeff Garzik --- drivers/ata/libata-core.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/ata/libata-core.c b/drivers/ata/libata-core.c index d2e686371870..011c0a8a2dcc 100644 --- a/drivers/ata/libata-core.c +++ b/drivers/ata/libata-core.c @@ -2303,7 +2303,7 @@ int ata_timing_compute(struct ata_device *adev, unsigned short speed, * DMA cycle timing is slower/equal than the fastest PIO timing. */ - if (speed > XFER_PIO_4) { + if (speed > XFER_PIO_6) { ata_timing_compute(adev, adev->pio_mode, &p, T, UT); ata_timing_merge(&p, t, t, ATA_TIMING_ALL); } -- cgit v1.2.1