| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
General support for state persistence is added to gpiolib with the
introduction of a new pinconf parameter to propagate the request to
hardware. The existing persistence support for sleep is adapted to
include hardware support if the GPIO driver provides it. Persistence
continues to be enabled by default; in-kernel consumers can opt out, but
userspace (currently) does not have a choice.
The *_SLEEP_MAY_LOSE_VALUE and *_SLEEP_MAINTAIN_VALUE symbols are
renamed, dropping the SLEEP prefix to reflect that the concept is no
longer sleep-specific. I feel that renaming to just *_MAY_LOSE_VALUE
could initially be misinterpreted, so I've further changed the symbols
to *_TRANSITORY and *_PERSISTENT to address this.
The sysfs interface is modified only to keep consistency with the
chardev interface in enforcing persistence for userspace exports.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
(cherry picked from commit e10f72bf4b3e8885c1915a119141481e7fc45ca8)
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
| |
|
|
|
|
|
|
|
| |
Add new flags to allow users to specify that they are not concerned with
the status of GPIOs whilst in a sleep/low power state.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently, the GPIO interface is said to Open Drain if it is Single
Ended and active LOW. Similarly, it is said as Open Source if it is
Single Ended and active HIGH.
The active HIGH/LOW is used in the interface for setting the pin
state to HIGH or LOW when enabling/disabling the interface.
In Open Drain interface, pin is set to HIGH by putting pin in
high impedance and LOW by driving to the LOW.
In Open Source interface, pin is set to HIGH by driving pin to
HIGH and set to LOW by putting pin in high impedance.
With above, the Open Drain/Source is unrelated to the active LOW/HIGH
in interface. There is interface where the enable/disable of interface
is ether active LOW or HIGH but it is Open Drain type.
Hence decouple the Open Drain with Single Ended + Active LOW and
Open Source with Single Ended + Active HIGH.
Adding different flag for the Open Drain/Open Source which is valid
only when Single ended flag is enabled.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
It is customary for GPIO controllers to support open drain/collector
and open source/emitter configurations. Add standard GPIO line flags
to account for this and augment the documentation to say that these
are the most generic bindings.
Several people approached me to add new flags to the lines, and this
makes sense, but let's first bind up the most common cases before we
start to add exotic stuff.
Thanks to H. Nikolaus Schaller for ideas on how to encode single-ended
wiring such as open drain/source and open collector/emitter.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
Many GPIO device tree bindings use the same flags. Create a header to
define those.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
|
