summaryrefslogtreecommitdiffstats
path: root/drivers/regulator
Commit message (Collapse)AuthorAgeFilesLines
* regulator: act8865: Fix act8600_sudcdc_voltage_ranges settingAxel Lin2019-04-051-2/+3
| | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit f01a7beb6791f1c419424c1a6958b7d0a289c974 ] The act8600_sudcdc_voltage_ranges setting does not match the datasheet. The problems in below entry: REGULATOR_LINEAR_RANGE(19000000, 191, 255, 400000), 1. The off-by-one min_sel causes wrong volatage calculation. The min_sel should be 192. 2. According to the datasheet[1] Table 7. (on page 43): The selector 248 (0b11111000) ~ 255 (0b11111111) are 41.400V. Also fix off-by-one for ACT8600_SUDCDC_VOLTAGE_NUM. [1] https://active-semi.com/wp-content/uploads/ACT8600_Datasheet.pdf Fixes: df3a950e4e73 ("regulator: act8865: Add act8600 support") Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* regulator: mcp16502: Include linux/gpio/consumer.h to fix build errorAxel Lin2019-04-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit f3c6a1a194317f3a31ee2b2067bb0a41de64bc8b ] Fix below build error: drivers/regulator/mcp16502.c: In function ‘mcp16502_gpio_set_mode’: drivers/regulator/mcp16502.c:135:3: error: implicit declaration of function ‘gpiod_set_value’; did you mean ‘gpio_set_value’? [-Werror=implicit-function-declaration] gpiod_set_value(mcp->lpm, 0); ^~~~~~~~~~~~~~~ gpio_set_value drivers/regulator/mcp16502.c: In function ‘mcp16502_probe’: drivers/regulator/mcp16502.c:486:13: error: implicit declaration of function ‘devm_gpiod_get’; did you mean ‘devm_gpio_free’? [-Werror=implicit-function-declaration] mcp->lpm = devm_gpiod_get(dev, "lpm", GPIOD_OUT_LOW); ^~~~~~~~~~~~~~ devm_gpio_free drivers/regulator/mcp16502.c:486:40: error: ‘GPIOD_OUT_LOW’ undeclared (first use in this function); did you mean ‘GPIOF_INIT_LOW’? mcp->lpm = devm_gpiod_get(dev, "lpm", GPIOD_OUT_LOW); ^~~~~~~~~~~~~ GPIOF_INIT_LOW Signed-off-by: Axel Lin <axel.lin@ingics.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* regulator: core: Take lock before applying system loadNiklas Cassel2019-04-051-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ Upstream commit e5e21f70bfd3a201e627b48aed82793d1bcd6f78 ] Take the regulator lock before applying system load. Fixes the following lockdep splat: [ 5.583581] WARNING: CPU: 1 PID: 16 at drivers/regulator/core.c:925 drms_uA_update+0x114/0x360 [ 5.588467] Modules linked in: [ 5.596833] CPU: 1 PID: 16 Comm: kworker/1:0 Not tainted 5.0.0-rc6-next-20190213-00002-g0fce66ab480f #18 [ 5.599933] Hardware name: Qualcomm Technologies, Inc. APQ 8016 SBC (DT) [ 5.609544] Workqueue: events qcom_channel_state_worker [ 5.616209] pstate: 60000005 (nZCv daif -PAN -UAO) [ 5.621152] pc : drms_uA_update+0x114/0x360 [ 5.626006] lr : drms_uA_update+0x110/0x360 [ 5.630084] sp : ffff0000124b3490 [ 5.634242] x29: ffff0000124b3490 x28: ffff800005326e00 [ 5.637735] x27: ffff0000124b35f8 x26: 000000000032bc48 [ 5.643117] x25: ffff800004c7e800 x24: ffff800004c6d500 [ 5.648411] x23: ffff800004c38a80 x22: 00000000000000d1 [ 5.653706] x21: 00000000001ab3f0 x20: ffff800004c7e800 [ 5.659001] x19: ffff0000114c3000 x18: ffffffffffffffff [ 5.664297] x17: 0000000000000000 x16: 0000000000000000 [ 5.669592] x15: ffff0000114c3808 x14: 0720072007200720 [ 5.674888] x13: 00000000199c9b28 x12: ffff80002bcccc40 [ 5.680183] x11: ffff000012286000 x10: ffff0000114c3808 [ 5.685477] x9 : 0720072007200720 x8 : ffff000010e9e808 [ 5.690772] x7 : ffff0000106da568 x6 : 0000000000000000 [ 5.696067] x5 : 0000000000000000 x4 : 0000000000000000 [ 5.701362] x3 : 0000000000000004 x2 : 0000000000000000 [ 5.706658] x1 : 0000000000000000 x0 : 0000000000000000 [ 5.711952] Call trace: [ 5.717223] drms_uA_update+0x114/0x360 [ 5.719405] regulator_register+0xb30/0x1140 [ 5.723230] devm_regulator_register+0x4c/0xa8 [ 5.727745] rpm_reg_probe+0xfc/0x1b0 [ 5.731992] platform_drv_probe+0x50/0xa0 [ 5.735727] really_probe+0x20c/0x2b8 [ 5.739718] driver_probe_device+0x58/0x100 [ 5.743368] __device_attach_driver+0x90/0xd0 [ 5.747363] bus_for_each_drv+0x64/0xc8 [ 5.751870] __device_attach+0xd8/0x138 [ 5.755516] device_initial_probe+0x10/0x18 [ 5.759341] bus_probe_device+0x98/0xa0 [ 5.763502] device_add+0x3d0/0x640 [ 5.767319] of_device_add+0x48/0x58 [ 5.770793] of_platform_device_create_pdata+0xb0/0x128 [ 5.774629] of_platform_bus_create+0x174/0x370 [ 5.779569] of_platform_populate+0x78/0xe0 [ 5.784082] qcom_smd_rpm_probe+0x80/0xa0 [ 5.788245] rpmsg_dev_probe+0x114/0x1a0 [ 5.792411] really_probe+0x20c/0x2b8 [ 5.796401] driver_probe_device+0x58/0x100 [ 5.799964] __device_attach_driver+0x90/0xd0 [ 5.803960] bus_for_each_drv+0x64/0xc8 [ 5.808468] __device_attach+0xd8/0x138 [ 5.812115] device_initial_probe+0x10/0x18 [ 5.815936] bus_probe_device+0x98/0xa0 [ 5.820099] device_add+0x3d0/0x640 [ 5.823916] device_register+0x1c/0x28 [ 5.827391] rpmsg_register_device+0x4c/0x90 [ 5.831216] qcom_channel_state_worker+0x170/0x298 [ 5.835651] process_one_work+0x294/0x6e8 [ 5.840241] worker_thread+0x40/0x450 [ 5.844318] kthread+0x11c/0x120 [ 5.847961] ret_from_fork+0x10/0x18 [ 5.851260] irq event stamp: 9090 [ 5.854820] hardirqs last enabled at (9089): [<ffff000010160798>] console_unlock+0x3e0/0x5b0 [ 5.858086] hardirqs last disabled at (9090): [<ffff0000100817cc>] do_debug_exception+0x104/0x140 [ 5.866596] softirqs last enabled at (9086): [<ffff000010082024>] __do_softirq+0x474/0x574 [ 5.875446] softirqs last disabled at (9079): [<ffff0000100f2254>] irq_exit+0x13c/0x148 [ 5.883598] ---[ end trace 6984ef7f081afa21 ]--- Fixes: fa94e48e13a1 ("regulator: core: Apply system load even if no consumer loads") Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Sasha Levin <sashal@kernel.org>
* regulator: s2mpa01: Fix step values for some LDOsStuart Menefy2019-03-231-5/+5
| | | | | | | | | | | | | | | commit 28c4f730d2a44f2591cb104091da29a38dac49fe upstream. The step values for some of the LDOs appears to be incorrect, resulting in incorrect voltages (or at least, ones which are different from the Samsung 3.4 vendor kernel). Signed-off-by: Stuart Menefy <stuart.menefy@mathembedded.com> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* regulator: max77620: Initialize values for DT propertiesMark Zhang2019-03-231-1/+9
| | | | | | | | | | | | | | | | commit 0ab66b3c326ef8f77dae9f528118966365757c0c upstream. If regulator DT node doesn't exist, its of_parse_cb callback function isn't called. Then all values for DT properties are filled with zero. This leads to wrong register update for FPS and POK settings. Signed-off-by: Jinyoung Park <jinyoungp@nvidia.com> Signed-off-by: Mark Zhang <markz@nvidia.com> Signed-off-by: Mark Brown <broonie@kernel.org> Cc: stable@vger.kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* regulator: s2mps11: Fix steps for buck7, buck8 and LDO35Krzysztof Kozlowski2019-03-231-3/+3
| | | | | | | | | | | | | | | | commit 56b5d4ea778c1b0989c5cdb5406d4a488144c416 upstream. LDO35 uses 25 mV step, not 50 mV. Bucks 7 and 8 use 12.5 mV step instead of 6.25 mV. Wrong step caused over-voltage (LDO35) or under-voltage (buck7 and 8) if regulators were used (e.g. on Exynos5420 Arndale Octa board). Cc: <stable@vger.kernel.org> Fixes: cb74685ecb39 ("regulator: s2mps11: Add samsung s2mps11 regulator driver") Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Merge remote-tracking branch 'regulator/topic/coupled' into regulator-nextMark Brown2018-12-211-10/+2
|\
| * regulator: core: Don't double-disable supplies in regulator_disable_deferred()Douglas Anderson2018-11-201-10/+0
| | | | | | | | | | | | | | | | | | | | | | | | In the commit f8702f9e4aa7 ("regulator: core: Use ww_mutex for regulators locking") disabling of the supply was moved into _regulator_disable(). That means regulator_disable_work() shouldn't be disabling since that double-disables the supply. Fixes: f8702f9e4aa7 ("regulator: core: Use ww_mutex for regulators locking") Signed-off-by: Douglas Anderson <dianders@chromium.org> Reviewed-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
| * regulator: core: Export regulator_lock and regulator_unlockDmitry Osipenko2018-11-201-0/+2
| | | | | | | | | | | | | | | | | | This fixes compiling regulator drivers that use these function when these drivers are built as kernel modules. Fixes: f8702f9e4aa7 ("regulator: core: Use ww_mutex for regulators locking") Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | regulator: tps65910: fix a missing check of return valueKangjie Lu2018-12-211-1/+3
| | | | | | | | | | | | | | | | tps65910_reg_set_bits() may fail. The fix checks if it fails, and if so, returns with its error code. Signed-off-by: Kangjie Lu <kjlu@umn.edu> Signed-off-by: Mark Brown <broonie@kernel.org>
* | regulator: mcp16502: Select REGMAP_I2C to fix build errorAxel Lin2018-12-211-0/+1
| | | | | | | | | | | | | | | | | | | | Fix build error when CONFIG_REGMAP_I2C=m && CONFIG_REGULATOR_MCP16502=y. drivers/regulator/mcp16502.o: In function `mcp16502_probe': mcp16502.c:(.text+0xca): undefined reference to `__devm_regmap_init_i2c' Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | regulator: convert to DEFINE_SHOW_ATTRIBUTEYangtao Li2018-12-202-63/+9
| | | | | | | | | | | | | | Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code. Signed-off-by: Yangtao Li <tiny.windzz@gmail.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | regulator: mcp16502: Fix missing n_voltages settingAxel Lin2018-12-201-0/+1
| | | | | | | | | | | | | | The n_voltages setting is not set, fix it. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | regulator: mcp16502: Use #ifdef CONFIG_PM_SLEEP around ↵Axel Lin2018-12-201-5/+2
| | | | | | | | | | | | | | | | | | | | | | mcp16502_suspend/resume_noirq mcp16502_suspend/resume_noirq is only used by SET_NOIRQ_SYSTEM_SLEEP_PM_OPS when CONFIG_PM_SLEEP is defined. So use #ifdef CONFIG_PM_SLEEP instead CONFIG_SUSPEND guard. Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | regulator: mcp16502: code cleanupAndrei.Stefanescu@microchip.com2018-12-191-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch does the following: - align parameter with parenthesis - fix compile error If CONFIG_SUSPEND is not set the dummy pm_ops callbacks are named mcp16502_suspend and mcp16502_resume instead of mcp16502_suspend_noirq and mcp16502_resume_noirq. Excerpt from compile log (kbuild test robot): In file included from include/linux/device.h:23:0, from include/linux/gpio/driver.h:5, from include/asm-generic/gpio.h:13, from include/linux/gpio.h:62, from drivers/regulator/mcp16502.c:11: >> drivers/regulator/mcp16502.c:527:32: error: 'mcp16502_suspend_noirq' undeclared here (not in a function); did you mean 'mcp16502_suspend'? SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(mcp16502_suspend_noirq, >> drivers/regulator/mcp16502.c:528:10: error: 'mcp16502_resume_noirq' undeclared here (not in a function); did you mean 'mcp16502_suspend_noirq'? mcp16502_resume_noirq) vim +527 drivers/regulator/mcp16502.c 524 525 #ifdef CONFIG_PM 526 static const struct dev_pm_ops mcp16502_pm_ops = { > 527 SET_NOIRQ_SYSTEM_SLEEP_PM_OPS(mcp16502_suspend_noirq, > 528 mcp16502_resume_noirq) 529 }; 530 #endif 531 static const struct i2c_device_id mcp16502_i2c_id[] = { 532 { "mcp16502", 0 }, 533 { } 534 }; 535 MODULE_DEVICE_TABLE(i2c, mcp16502_i2c_id); 536 Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | regulator: act8945a-regulator: make symbol act8945a_pm staticWei Yongjun2018-12-191-1/+1
| | | | | | | | | | | | | | | | | | | | | | Fixes the following sparse warning: drivers/regulator/act8945a-regulator.c:340:1: warning: symbol 'act8945a_pm' was not declared. Should it be static? Fixes: 7482d6ecc68e ("regulator: act8945a-regulator: Implement PM functionalities") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | drivers/regulator: fix a missing check of return valueKangjie Lu2018-12-191-1/+4
| | | | | | | | | | | | | | | | | | | | If palmas_smps_read() fails, we should not use the read data in "reg" which may contain random value. The fix inserts a check for the return value of palmas_smps_read(): If it fails, we return the error code upstream and stop using "reg". Signed-off-by: Kangjie Lu <kjlu@umn.edu> Signed-off-by: Mark Brown <broonie@kernel.org>
* | regulator: act8945a-regulator: fix 'defined but not used' compiler warningClaudiu Beznea2018-12-171-1/+1
| | | | | | | | | | | | | | | | | | | | Fix 'defined but not used' compiler warning for act8945a_suspend() function in case CONFIG_PM_SLEEP is not defined. Fixes: b5ebba46e694 ("regulator: act8945a-regulator: add shutdown function") Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Reported-by: Andrei Stefanescu <andrei.stefanescu@microchip.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | regulator: axp20x: fix set_ramp_delay for AXP209/dcdc2Priit Laes2018-12-171-0/+1
| | | | | | | | | | | | | | | | | | | | Initial commit of set_ramp_delay feature was missing an assignment which should have populated slew_rate table for dcdc2 regulator. Add it. Fixes: d29f54df8b16 ("regulator: axp20x: add support for set_ramp_delay for AXP209") Signed-off-by: Priit Laes <plaes@plaes.org> Signed-off-by: Mark Brown <broonie@kernel.org>
* | regulator: mcp16502: add support for suspendAndrei.Stefanescu@microchip.com2018-12-141-0/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for entering/resuming suspend states. It does this by setting the LPM pin of the PMIC. When suspending the PMIC will enter the Low-power mode when the LPM pin will be set to high. If the suspend target state is suspend-to-mem, the PMIC will transition to Hibernate mode, otherwise, if it is standby, it will remain in Low-power mode. Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | regulator: axp20x: add software based soft_start for AXP209 LDO3Olliver Schinagl2018-12-131-1/+56
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In the past, there have been words on various lists that if LDO3 is disabled in u-boot, but enabled in the DTS, the axp209 driver would fail to continue/hang. Several enable/disable patches have been issues to devicetree's in both the kernel and u-boot to address this issue. What really happened however, was that the AXP209 shuts down without a notice and without setting an interrupt. This is caused when LDO3 gets overloaded, for example with large capacitors on the LDO3 output. Normally, we would expect that AXP209 would source 200 mA as per datasheet and set and trigger an interrupt when being overloaded. For some reason however, this does not happen. As a work-around, we use the soft-start constraint of the regulator node to first bring up the LDO3 to the lowest possible voltage and then enable the LDO. After that, we can set the requested voltage as usual. Combining this setting with the regulator-ramp-delay allows LDO3 to enable voltage slowly and staggered, potentially reducing overall inrush current. Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> Signed-off-by: Priit Laes <plaes@plaes.org> Signed-off-by: Mark Brown <broonie@kernel.org>
* | regulator: axp20x: add support for set_ramp_delay for AXP209Olliver Schinagl2018-12-131-0/+85
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The AXP209 supports ramping up voltages on several regulators such as DCDC2 and LDO3. This patch adds preliminary support for the regulator-ramp-delay property for these 2 regulators. Note that the voltage ramp only works when regulator is already enabled. E.g. when going from say 0.7 V to 3.6 V. When turning on the regulator, no voltage ramp is performed in hardware. What this means, is that if the bootloader brings up the voltage at 0.7 V, the ramp delay property is properly applied. If however, the bootloader leaves the power off, no ramp delay is applied when the power is enabled by the regulator framework. Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> Signed-off-by: Priit Laes <plaes@plaes.org> Signed-off-by: Mark Brown <broonie@kernel.org>
* | Merge branch 'topic/axp20x' of ↵Mark Brown2018-12-131-178/+555
|\ \ | | | | | | | | | https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-4.21
| * | regulator: axp20x: use defines for masksOlliver Schinagl2018-11-281-178/+555
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The AXP20X driver currently has several masks defined throughout the code. Use nice defines to make them clean and more descriptive. Additionally include bitops.h, which was missing before, and sort headers. Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> Signed-off-by: Priit Laes <plaes@plaes.org> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | regulator: mcp16502: add regulator driver for MCP16502Andrei.Stefanescu@microchip.com2018-12-133-0/+530
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds a regulator driver for the MCP16502 PMIC. This drivers supports basic operations through the regulator interface such as: - setting/reading voltage - setting/reading operating mode - reading current status Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | regulator: act8945a-regulator: add shutdown functionClaudiu Beznea2018-12-121-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Implement shutdown method to make sure the PMIC will not enter the suspend state when the system is shutdown. This work is based on work done by Borris Brezillon on [1]. [1] https://www.spinics.net/lists/kernel/msg2942960.html Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | regulator: act8945a-regulator: fix line over 80 chars warningClaudiu Beznea2018-12-121-1/+2
| | | | | | | | | | | | | | | | | | | | | Fix line over 80 chars checkpatch.pl warning. Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | regulator: act8945a-regulator: Implement PM functionalitiesBoris Brezillon2018-12-121-5/+181
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The regulator supports a dedicated suspend mode. Implement the appropriate ->set_suspend_xx() hooks, add support for ->set_mode(), and provide basic PM ops functionalities to setup the regulator in a suspend state when the system is entering suspend. Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com> [claudiu.beznea@microchip.com: remove shutdown function, use dev_pm_ops, fix checkpatch warning, adapt commit message, add LDO modes support, move modes constants to active-semi,8945a-regulator.h, remove rdevs from struct act8945a_pmic, add op_mode to act8945a_pmic] Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | regulator: act8945a-regulator: unlock expert registersClaudiu Beznea2018-12-121-1/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Unlock expert registers for act8945a. This is based on orginal work of Boris Brezillon at [1]. [1] https://www.spinics.net/lists/kernel/msg2942960.html Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | regulator: arizona-ldo1: Rely on core to handle GPIO descriptorLinus Walleij2018-12-121-3/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After making sure that the regulator core always take over handling of the GPIO descriptors, the gpiod_put() on the errorpath of the Arizona LDO1 driver becomes redundant. Reported-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | regulator: wm8994: Rely on core to handle GPIO descriptorLinus Walleij2018-12-121-5/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | After making sure that the regulator core always take over handling of the GPIO descriptors, the gpiod_put() on the errorpath of the wm8994 driver becomes redundant. Reported-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | regulator: core: Clean enabling always-on regulators + their suppliesDouglas Anderson2018-12-111-3/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | At the end of regulator_resolve_supply() we have historically turned on our supply in some cases. This could be for one of two reasons: 1. If resolving supplies was happening before the call to set_machine_constraints() we needed to predict if set_machine_constraints() was going to turn the regulator on and we needed to preemptively turn the supply on. 2. Maybe set_machine_constraints() happened before we could resolve supplies (because we failed the first time to resolve) and thus we might need to propagate an enable that already happened up to our supply. Historically regulator_resolve_supply() used _regulator_is_enabled() to decide whether to turn on the supply. Let's change things a little bit. Specifically: 1. Let's try to enable the supply and the regulator in the same place, both in set_machine_constraints(). This means that we have exactly the same logic for enabling the supply and the regulator. 2. Let's properly set use_count when we enable always-on or boot-on regulators even for those that don't have supplies. The previous commit 1fc12b05895e ("regulator: core: Avoid propagating to supplies when possible") only did this right for regulators with supplies. 3. Let's make it clear that the only time we need to enable the supply in regulator_resolve_supply() is if the main regulator is currently in use. By using use_count (like the rest of the code) to decide if we're going to enable our supply we keep everything consistent. Overall the new scheme should be cleaner and easier to reason about. In addition to fixing regulator_summary to be more correct (because of the more correct use_count), this change also has the effect of no longer using _regulator_is_enabled() in this code path. _regulator_is_enabled() could return an error code for some regulators at bootup (like RPMh) that can't read their initial state. While one can argue that the design of those regulators is sub-optimal, the new logic sidesteps this brokenness. This fix in particular fixes observed problems on Qualcomm sdm845 boards which use the above-mentioned RPMh regulator. Those problems were made worse by commit 1fc12b05895e ("regulator: core: Avoid propagating to supplies when possible") because now we'd think at bootup that the SD regulators were already enabled and we'd never try them again. Fixes: 1fc12b05895e ("regulator: core: Avoid propagating to supplies when possible") Reported-by: Evan Green <evgreen@chromium.org> Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | Merge branch 'for-linus' of ↵Mark Brown2018-12-112-11/+12
|\ \ \ | | | | | | | | | | | | https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into regulator-4.21
| * \ \ Merge branch 'regulator-4.20' into regulator-linusMark Brown2018-12-112-11/+12
| |\ \ \ | | |/ / | |/| |
| | * | regulator: core: enable power when setting up constraintsOlliver Schinagl2018-11-261-11/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When a regulator is marked as always on, it is enabled early on, when checking and setting up constraints. It makes the assumption that the bootloader properly initialized the regulator, and just in case enables the regulator anyway. Some constraints however currently get missed, such as the soft-start and ramp-delay. This causes the regulator to be enabled, without the soft-start and ramp-delay being applied, which in turn can cause high-currents or other start-up problems. By moving the always-enabled constraints later in the constraints check, we can at least ensure all constraints for the regulator are followed. Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> Signed-off-by: Priit Laes <plaes@plaes.org> Signed-off-by: Mark Brown <broonie@kernel.org>
| | * | regulator: bd718x7: add missing linux/of.h inclusion (deja-vu)Matti Vaittinen2018-11-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | 0-Day tests found compilation error on x86. Driver won't compile on x86_64 as "of_match_ptr" is not found. Add missing include <linux/of.h> At some point this fix was lost. So re-apply it. Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | | regulator: s2mps11: Hand over GPIO to regulator coreLinus Walleij2018-12-111-1/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GPIO descriptors used by the S2MPS11 driver are retrieved during probe() and it is really helpful to have those under devres management because of all the errorpaths in the intialization. Using the new dev_gpiod_unhinge() call we can remove the devres management of the descriptor right before handing it over to the regulators core. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | | regulator: tps65090: Hand over GPIO to regulator coreLinus Walleij2018-12-111-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GPIO descriptors used by the TPS65090 driver are retrieved during probe() and it is really helpful to have those under devres management because of all the errorpaths in the intialization. Using the new dev_gpiod_unhinge() call we can remove the devres management of the descriptor right before handing it over to the regulators core. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | | regulator: s5m8767: Hand over GPIO to regulator coreLinus Walleij2018-12-111-1/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GPIO descriptors used by the S5M8767 driver are retrieved during probe() and it is really helpful to have those under devres management because of all the errorpaths in the intialization. Using the new dev_gpiod_unhinge() call we can remove the devres management of the descriptor right before handing it over to the regulators core. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | | regulator: da9211: Hand over GPIO to regulator coreLinus Walleij2018-12-111-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GPIO descriptors used by the DA9211 driver are retrieved during probe() and it is really helpful to have those under devres management because of all the errorpaths in the intialization. Using the new dev_gpiod_unhinge() call we can remove the devres management of the descriptor right before handing it over to the regulators core. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | | regulator: max8973: Let core handle GPIO descriptorLinus Walleij2018-12-111-1/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The probe path of this driver is a bit complex: sometimes the GPIO descriptor is passed to the regulator core, sometimes it is not. To handle it in a simple way: stick with the devm_* resource management and unhinge the GPIO descriptor devres handling right before passing it to the regulator core, if we pass it to the regulator core. Fixes: e7d2be696faa ("regulator: max8973: Pass descriptor instead of GPIO number") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | | regulator: max77686: Let core handle GPIO descriptorLinus Walleij2018-12-111-5/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the gpiod_get_from_of_node() rather than the devm_* version so that the regulator core can handle the lifecycle of these descriptors. Fix up the errorpath so that we free this descriptor if an error occurs in the callback. Rely on the regulator core to deal with it after this point: a previous patch fixed up the regulator core to properly dispose any GPIO descriptors once you call regulator_register(). Fixes: 96392c3d8ca4 ("regulator: max77686: Pass descriptor instead of GPIO number") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | | regulator: max8952: Let core handle GPIO descriptorLinus Walleij2018-12-111-3/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the gpiod_get() rather than the devm_* version so that the regulator core can handle the lifecycle of these descriptors. Fixes: d7a261c2d1f2 ("regulator: max8952: Pass descriptor instead of GPIO number") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | | regulator: lp8788-ldo: Let core handle GPIO descriptorLinus Walleij2018-12-111-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the gpiod_get() rather than the devm_* version so that the regulator core can handle the lifecycle of these descriptors. Fixes: 2468f0d51548 ("regulator: lp8788-ldo: Pass descriptor instead of GPIO number") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | | regulator: lm363x: Let core handle GPIO descriptorLinus Walleij2018-12-111-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the gpiod_get() rather than the devm_* version so that the regulator core can handle the lifecycle of these descriptors. Fixes: b2d751b7f69b ("regulator: lm363x: Pass descriptor instead of GPIO number") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | | regulator: fixed: Let core handle GPIO descriptorLinus Walleij2018-12-111-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the gpiod_get() rather than the devm_* version so that the regulator core can handle the lifecycle of these descriptors. Fixes: efdfeb079cc3 ("regulator: fixed: Convert to use GPIO descriptor only") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | | regulator: core: Track dangling GPIO descriptorsLinus Walleij2018-12-111-10/+45
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If a GPIO descriptor is passed to the regulator_register() function inside the config->ena_gpiod callers must be sure that once they call this API the regulator core owns that descriptor and will make sure to issue gpiod_put() on it, no matter whether the call is successful or not. For device tree regulators, the regulator core will automatically set up regulator init data from the device tree when registering a regulator by calling regulator_of_get_init_data() which in turn calls down to the regulator driver's .of_parse_cb() callback. This callback (in drivers such as for max77686) may also choose to fill in the config->ena_gpiod field with a GPIO descriptor. Harden the errorpath of regulator_register() to properly gpiod_put() any passed in cfg->ena_gpiod or any gpiod coming from the device tree on any type of error. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com> Tested-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | | regulator: Use of_node_name_eq for node name comparisonsRob Herring2018-12-066-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Convert string compares of DT node names to use of_node_name_eq helper instead. This removes direct access to the node name pointer. For instances using of_node_cmp, this has the side effect of now using case sensitive comparisons. This should not matter for any FDT based system which all of these are. Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Support Opensource <support.opensource@diasemi.com> Cc: Sangbeom Kim <sbkim73@samsung.com> Cc: Krzysztof Kozlowski <krzk@kernel.org> Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Cc: linux-samsung-soc@vger.kernel.org Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | | regulator: Allow regulator nodes to contain their own init dataCharles Keepax2018-12-041-2/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently it is expected that regulator init data will be defined as a series of sub-nodes from the node that bound in the driver. Add support for a node to both bind in a driver and contain init data for that regulator. Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
* | | | regulator: Factor out location of init data OF nodeCharles Keepax2018-12-041-27/+37
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | To support future additions factor out the location of the OF node containing the init data for the regulator from the code that parses the init data. Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com> Signed-off-by: Mark Brown <broonie@kernel.org>
OpenPOWER on IntegriCloud