summaryrefslogtreecommitdiffstats
path: root/drivers/net/smsc911x.c
Commit message (Collapse)AuthorAgeFilesLines
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6Linus Torvalds2010-05-201-4/+3
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits) qlcnic: adding co maintainer ixgbe: add support for active DA cables ixgbe: dcb, do not tag tc_prio_control frames ixgbe: fix ixgbe_tx_is_paused logic ixgbe: always enable vlan strip/insert when DCB is enabled ixgbe: remove some redundant code in setting FCoE FIP filter ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp ixgbe: fix header len when unsplit packet overflows to data buffer ipv6: Never schedule DAD timer on dead address ipv6: Use POSTDAD state ipv6: Use state_lock to protect ifa state ipv6: Replace inet6_ifaddr->dead with state cxgb4: notify upper drivers if the device is already up when they load cxgb4: keep interrupts available when the ports are brought down cxgb4: fix initial addition of MAC address cnic: Return SPQ credit to bnx2x after ring setup and shutdown. cnic: Convert cnic_local_flags to atomic ops. can: Fix SJA1000 command register writes on SMP systems bridge: fix build for CONFIG_SYSFS disabled ARCNET: Limit com20020 PCI ID matches for SOHARD cards ... Fix up various conflicts with pcmcia tree drivers/net/ {pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and wireless/orinoco/spectrum_cs.c} and feature removal (Documentation/feature-removal-schedule.txt). Also fix a non-content conflict due to pm_qos_requirement getting renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
| * net: trans_start cleanupsEric Dumazet2010-05-101-1/+0
| | | | | | | | | | | | | | | | | | | | | | Now that core network takes care of trans_start updates, dont do it in drivers themselves, if possible. Drivers can avoid one cache miss (on dev->trans_start) in their start_xmit() handler. Exceptions are NETIF_F_LLTX drivers Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * Merge branch 'master' of ↵David S. Miller2010-04-111-1/+0
| |\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/stmmac/stmmac_main.c drivers/net/wireless/wl12xx/wl1271_cmd.c drivers/net/wireless/wl12xx/wl1271_main.c drivers/net/wireless/wl12xx/wl1271_spi.c net/core/ethtool.c net/mac80211/scan.c
| * | net: convert multicast list to list_headJiri Pirko2010-04-031-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Converts the list and the core manipulating with it to be the same as uc_list. +uses two functions for adding/removing mc address (normal and "global" variant) instead of a function parameter. +removes dev_mcast.c completely. +exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for manipulation with lists on a sandbox (used in bonding and 80211 drivers) Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | Merge branch 'master' into for-nextJiri Kosina2010-04-231-1/+0
|\ \ \ | | |/ | |/|
| * | include cleanup: Update gfp.h and slab.h includes to prepare for breaking ↵Tejun Heo2010-03-301-1/+0
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
* | Fix typos in commentsThomas Weber2010-03-161-2/+2
|/ | | | | | | | | | | [Ss]ytem => [Ss]ystem udpate => update paramters => parameters orginal => original Signed-off-by: Thomas Weber <swirl@gmx.li> Acked-by: Randy Dunlap <rdunlap@xenotime.net> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* smsc911x: convert to use netdev_for_each_mc_addrJiri Pirko2010-02-181-18/+9
| | | | | | | also removed unnecessary checks Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* smsc911x: replace manual phy lookup.kirjanov@gmail.com2010-02-171-14/+10
| | | | | | | | Use phy_find_first() function instead of manual lookup. Signed-off-by: Denis Kirjanov <kirjanov@gmail.com> Reviewed-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: use netdev_mc_count and netdev_mc_empty when appropriateJiri Pirko2010-02-121-2/+2
| | | | | | | | | | | This patch replaces dev->mc_count in all drivers (hopefully I didn't miss anything). Used spatch and did small tweaks and conding style changes when it was suitable. Jirka Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* const: constify remaining dev_pm_opsAlexey Dobriyan2009-12-151-1/+1
| | | | | | Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Merge branch 'for-linus' of ↵Linus Torvalds2009-12-091-1/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (42 commits) tree-wide: fix misspelling of "definition" in comments reiserfs: fix misspelling of "journaled" doc: Fix a typo in slub.txt. inotify: remove superfluous return code check hdlc: spelling fix in find_pvc() comment doc: fix regulator docs cut-and-pasteism mtd: Fix comment in Kconfig doc: Fix IRQ chip docs tree-wide: fix assorted typos all over the place drivers/ata/libata-sff.c: comment spelling fixes fix typos/grammos in Documentation/edac.txt sysctl: add missing comments fs/debugfs/inode.c: fix comment typos sgivwfb: Make use of ARRAY_SIZE. sky2: fix sky2_link_down copy/paste comment error tree-wide: fix typos "couter" -> "counter" tree-wide: fix typos "offest" -> "offset" fix kerneldoc for set_irq_msi() spidev: fix double "of of" in comment comment typo fix: sybsystem -> subsystem ...
| * Merge branch 'for-next' into for-linusJiri Kosina2009-12-071-1/+1
| |\ | | | | | | | | | | | | | | | Conflicts: kernel/irq/chip.c
| | * tree-wide: fix assorted typos all over the placeAndré Goddard Rosa2009-12-041-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | That is "success", "unknown", "through", "performance", "[re|un]mapping" , "access", "default", "reasonable", "[con]currently", "temperature" , "channel", "[un]used", "application", "example","hierarchy", "therefore" , "[over|under]flow", "contiguous", "threshold", "enough" and others. Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* | | drivers/net: Move && and || to end of previous lineJoe Perches2009-12-031-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Only files where David Miller is the primary git-signer. wireless, wimax, ixgbe, etc are not modified. Compile tested x86 allyesconfig only Not all files compiled (not x86 compatible) Added a few > 80 column lines, which I ignored. Existing checkpatch complaints ignored. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | | Merge branch 'master' of ↵David S. Miller2009-11-171-1/+1
|\ \ \ | |/ / | | | | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/can/Kconfig
| * | smsc911x: Fix Console Hang when bringing the interface down.Sriram2009-11-151-1/+1
| |/ | | | | | | | | | | | | | | | | | | | | | | In the NAPI poll function, check for netif_running() is unnecassary. In addition to associated runtime overhead, it also results in continuous softirq loop when the interface is brought down under heavy traffic(tested with Traffic Generator).Once the interface is disabled, the poll function always returns zero(with the check for netif_running) and napi_complete() would never get called resulting in softirq loop. Signed-off-by: Sriramakrishnan <srk@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: smsc911x: allow platform_data to specify mac addressManuel Lauss2009-10-131-0/+3
|/ | | | | | | Extend the driver to accept a MAC address specified in platform_data. Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers: Kill now superfluous ->last_rx storesEric Dumazet2009-09-021-1/+0
| | | | | | | | | | The generic packet receive code takes care of setting netdev->last_rx when necessary, for the sake of the bonding ARP monitor. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Acked-by: Neil Horman <nhorman@txudriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: smsc911x: switch to new dev_pm_opsDaniel Mack2009-08-061-11/+20
| | | | | | | | | | Hibernation is unsupported for now, which meets the actual implementation in the driver. For free/thaw, the chip's D2 state should be entered. Signed-off-by: Daniel Mack <daniel@caiaq.de> Acked-by: <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netdev: restore MTU change operationBen Hutchings2009-07-121-0/+1
| | | | | | | | | alloc_etherdev() used to install a default implementation of this operation, but it must now be explicitly installed in struct net_device_ops. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* drivers/net/smsc911x.c: Fix resource size off by 1 errorJulia Lawall2009-07-051-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The call resource_size(res) returns res->end - res->start + 1 and thus the second change is semantics-preserving. res_size is then used as the second argument of a call to request_mem_region, and the memory allocated by this call appears to be the same as what is released in the two calls to release_mem_region. So the size argument for those calls should be resource_size(size) as well. Alternatively, in the second call to release_mem_region, the second argument could be res_size, as that variable has already been initialized at the point of this call. The problem was found using the following semantic patch: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @@ struct resource *res; @@ - (res->end - res->start) + 1 + resource_size(res) @@ struct resource *res; @@ - res->end - res->start + BAD(resource_size(res)) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
* netdev: smsc911x: add missing __devexit_p() usageMike Frysinger2009-06-081-1/+1
| | | | | | | | | The smsc911x_drv_remove() function is declared with __devexit, so the assignment to the driver structure needs __devexit_p() wrappings to prevent build failure when hotplug is disabled. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* smsc911x: fix calculation of res_size for ioremapMatthias Ludwig2009-05-071-1/+1
| | | | | | | | | fix size of remaped iomem, which is 1 byte to small (e.g. mappes only 0xff bytes instead of 0x100) Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de> Acked-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: smsc911x: add power management functionsDaniel Mack2009-05-051-0/+46
| | | | | | | | | | This adds a power management implementation for smsc911x.c which assumes the chips remains powered during suspend. The device is put in its D1 power saving mode. Signed-off-by: Daniel Mack <daniel@caiaq.de> Acked-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* smsc911x: add fifo byteswap support V2Magnus Damm2009-04-281-0/+13
| | | | | | | | | | | | | | | | This is V2 of the smsc911x fifo byteswap patch. The smsc911x hardware supports both big and little and endian hardware configurations, and the linux smsc911x driver currently detects word order. For correct operation on big endian platforms lacking swapped byte lanes the following patch is needed. Only fifo data is swapped, register data does not require any swapping. Signed-off-by: Magnus Damm <damm@igel.co.jp> Acked-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* smsc911x: correct debugging message on mii read timeoutSteve Glendinning2009-04-081-1/+1
| | | | | | | | the warning printed when a mii READ times out currently says "Timed out waiting for MII write to finish". This patch corrects this. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* smsc911x: remove unused #include <linux/version.h>Huang Weiyi2009-04-061-1/+0
| | | | | | | Remove unused #include <linux/version.h> in drivers/net/smsc911x.c. Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* smsc911x: enforce read-after-write timing restriction on eeprom accessSteve Glendinning2009-03-271-0/+5
| | | | | | | | | The LAN911x datasheet specifies a minimum delay of 45ns between a write of E2P_DATA and any read. This patch adds a single dummy read of BYTE_TEST to enforce this timing constraint. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge branch 'master' of ↵David S. Miller2009-03-201-0/+4
|\ | | | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/virtio_net.c
| * smsc911x: reset last known duplex and carrier on openSteve Glendinning2009-03-181-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | smsc911x_phy_adjust_link is called periodically by the phy layer (as it's run in polling mode), and it only updates the hardware when it sees a change in duplex or carrier. This patch clears the last known values every time the interface is brought up, instead of only when the module is loaded. Without this patch the adjust_link function never updates the hardware after an ifconfig down; ifconfig up. On a full duplex link this causes the tx error counter to increment, even though packets are correctly transmitted, as the default MAC_CR register setting is for half duplex. The tx errors are "no carrier" errors, which should be ignored in full-duplex mode. When MAC_CR is set to "full duplex" mode they are correctly ignored by the hardware. Note that even with this patch the tx error counter can increment if packets are transmitted between "ifconfig up" and the first phy poll interval. An improved solution would use the phy interrupt with phylib, but I haven't managed to make this work 100% robustly yet. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | smsc911x: allow setting of mac addressSteve Glendinning2009-03-191-5/+30
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch replaces the generic eth_mac_addr function with one that also updates the hardware mac address registers. It also renames the existing smsc911x_set_mac_address function to smsc911x_hw_set_mac_address for clarity. Newer LAN911x and all LAN921x devices also support changing the mac address while the device is running, which is useful for some bonding modes. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | smsc911x: replace print_mac with %pMSteve Glendinning2009-03-191-3/+1
| | | | | | | | | | Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | smsc911x: define status word positions as constantsSteve Glendinning2009-03-191-10/+8
| | | | | | | | | | | | | | | | | | | | The vast majority of bit constants in this driver are defined in the header file, but TX and RX status word bits are not. This patch (which should make no functional change) defines these, to make the driver slightly more readable. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | smsc911x: improve EEPROM loading timeout logic in openSteve Glendinning2009-03-131-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch from Juha Leppanen suppresses a false warning if the eeprom load succeeds on the very last attempt. Juha> In function smsc911x_open smsc911x_reg_read+udelay can be run 50 Juha> times with timeout reaching -1, and the following if statetement Juha> does not catch the timeout and no warning is issued. Also if the Juha> 50th smsc911x_reg_read is GOOD, loop is exited with timeout as 0 Juha> and bogus warning issued. Replace testing order and --timeout Juha> instead of timeout-- and now max 50 smsc911x_reg_read's are done, Juha> with max 49 udelays. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | smsc911x: check for FFWD success before checking for timeoutSteve Glendinning2009-03-131-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch from Juha Leppanen suppresses a false warning if a fast forward operation succeeds on the very last attempt. Juha> If smsc911x_reg_read loop is executed 500 times, timeout reaches 0 Juha> and the 500th smsc911x_reg_read result in val is ignored. If Juha> testing order is changed, then val is checked first. The 500th Juha> reg_read might be GOOD, why ignore it! Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge branch 'master' of /home/davem/src/GIT/linux-2.6/David S. Miller2009-02-241-1/+1
|\ \ | |/
| * SMSC: timeout reaches -1Roel Kluin2009-02-201-1/+1
| | | | | | | | | | | | | | | | With a postfix decrement timeouts will reach -1 rather than 0, so the error path does not appear. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | smsc911x: allow mac address to be saved before device resetSteve Glendinning2009-02-011-8/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some platforms (for example pcm037) do not have an EEPROM fitted, instead storing their mac address somewhere else. The bootloader fetches this and configures the ethernet adapter before the kernel is started. This patch allows a platform to indicate to the driver via the SMSC911X_SAVE_MAC_ADDRESS flag that the mac address has already been configured via such a mechanism, and should be saved before resetting the chip. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Tested-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* | smsc911x: add external phy detection overridesSteve Glendinning2009-02-011-37/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On LAN9115/LAN9117/LAN9215/LAN9217, external phys are supported. These are usually indicated by a hardware strap which sets an "external PHY detected" bit in the HW_CFG register. In some cases it is desirable to override this hardware strap and force use of either the internal phy or an external PHY. This patch adds SMSC911X_FORCE_INTERNAL_PHY and SMSC911X_FORCE_EXTERNAL_PHY flags so a platform can indicate this preference via its platform_data. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Acked-by: Sascha Hauer <s.hauer@pengutronix.de> Tested-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* | smsc911x: register isr as IRQF_SHAREDSteve Glendinning2009-02-011-1/+1
| | | | | | | | | | | | | | | | | | | | | | The isr supports shared operation, so register it with the IRQF_SHARED flag to indicate this. This patch also removes the IRQF_DISABLED flag. This driver doesn't need it, and IRQF_DISABLED isn't guaranteed when using shared interrupts. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | smsc911x: add support for platform-specific irq flagsSteve Glendinning2009-02-011-5/+14
| | | | | | | | | | | | | | | | | | | | this patch adds support for the platform_device's resources to indicate additional flags to use when registering the irq, for example IORESOURCE_IRQ_LOWLEVEL (which corresponds to IRQF_TRIGGER_LOW). These should be set in the irq resource flags field. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge branch 'master' of ↵David S. Miller2009-01-301-1/+1
|\ \ | |/ | | | | | | | | | | master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/e1000/e1000_main.c
| * smsc911x: timeout reaches -1Roel Kluin2009-01-291-1/+1
| | | | | | | | | | | | | | | | | | With a postfix decrement the timeout will reach -1 rather than 0, so the warning will not be issued. Signed-off-by: Roel Kluin <roel.kluin@gmail.com> Acked-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | smsc911x: leave RX_STOP interrupt permanently enabledSteve Glendinning2009-01-261-10/+3
| | | | | | | | | | | | | | | | | | | | smsc911x_set_multicast_list currently performs the only non-atomic read-modify-write of INT_EN. This patch permanently enables the RXSTOP_INT interrupt, and changes the ISR to only conditionally run the multicast filter workaround code. Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: struct device - replace bus_id with dev_name(), dev_set_name()Kay Sievers2009-01-261-3/+4
| | | | | | | | | | | | Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Acked-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: Remove redundant NAPI functionsBen Hutchings2009-01-211-4/+4
|/ | | | | | | | | | | Following the removal of the unused struct net_device * parameter from the NAPI functions named *netif_rx_* in commit 908a7a1, they are exactly equivalent to the corresponding *napi_* functions and are therefore redundant. Signed-off-by: Ben Hutchings <bhutchings@solarflare.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* smsc911x: register irq with device name, not driver nameSteve Glendinning2009-01-111-1/+1
| | | | | | | | This change lets "cat /proc/interrupts" show the name of the ethernet device (e.g. eth0) rather than the driver name (smsc911x). Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* smsc911x: fix smsc911x_reg_read compiler warningSteve Glendinning2009-01-111-0/+1
| | | | | | | | | | | | | | | if this code path is ever hit, the platform_data struct isn't properly configured with a bus width flag so the device won't work (hence the BUG()). This patch adds a dummy return statement to eliminate this compiler warning: drivers/net/smsc911x.c: In function 'smsc911x_reg_read': drivers/net/smsc911x.c:148: warning: control reaches end of non-void function Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* netdev: add missing set_mac_address hookStephen Hemminger2009-01-111-0/+1
| | | | | | | | Many drivers lost the ability to set ethernet address accidently during the net_device_ops conversion. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
OpenPOWER on IntegriCloud