summaryrefslogtreecommitdiffstats
path: root/drivers/net/phy/micrel.c
Commit message (Collapse)AuthorAgeFilesLines
* net: phy: micrel: add 125MHz reference clock workaroundMarkus Niebel2018-05-161-0/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | The micrel KSZ9031 phy has a optional clock pin (CLK125_NDO) which can be used as reference clock for the MAC unit. The clock signal must meet the RGMII requirements to ensure the correct data transmission between the MAC and the PHY. The KSZ9031 phy does not fulfill the duty cycle requirement if the phy is configured as slave. For a complete describtion look at the errata sheets: DS80000691D or DS80000692D. The errata sheet recommends to force the phy into master mode whenever there is a 1000Base-T link-up as work around. Only set the "micrel,force-master" property if you use the phy reference clock provided by CLK125_NDO pin as MAC reference clock in your application. Attenation, this workaround is only usable if the link partner can be configured to slave mode for 1000Base-T. Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de> [m.felsch@pengutronix.de: fix dt-binding documentation] [m.felsch@pengutronix.de: use already existing result var for read/write] [m.felsch@pengutronix.de: add error handling] [m.felsch@pengutronix.de: add more comments] Signed-off-by: Marco Felsch <m.felsch@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: micrel: Use the general dummy stubs for MMD register accessKevin Hao2018-03-221-21/+2
| | | | | | | | The new general dummy stubs for MMD register access were introduced. Use that for the codes reuse. Signed-off-by: Kevin Hao <haokexin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: micrel: Use strlcpy() for ethtool::get_stringsFlorian Fainelli2018-03-061-2/+2
| | | | | | | | | | | | Our statistics strings are allocated at initialization without being bound to a specific size, yet, we would copy ETH_GSTRING_LEN bytes using memcpy() which would create out of bounds accesses, this was flagged by KASAN. Replace this with strlcpy() to make sure we are bound the source buffer size and we also always NUL-terminate strings. Fixes: 2b2427d06426 ("phy: micrel: Add ethtool statistics counters") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2017-12-291-0/+1
|\ | | | | | | | | | | | | | | | | | | | | net/ipv6/ip6_gre.c is a case of parallel adds. include/trace/events/tcp.h is a little bit more tricky. The removal of in-trace-macro ifdefs in 'net' paralleled with moving show_tcp_state_name and friends over to include/trace/events/sock.h in 'net-next'. Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: phy: micrel: ksz9031: reconfigure autoneg after phy autoneg workaroundGrygorii Strashko2017-12-261-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Under some circumstances driver will perform PHY reset in ksz9031_read_status() to fix autoneg failure case (idle error count = 0xFF). When this happens ksz9031 will not detect link status change any more when connecting to Netgear 1G switch (link can be recovered sometimes by restarting netdevice "ifconfig down up"). Reproduced with TI am572x board equipped with ksz9031 PHY while connecting to Netgear 1G switch. Fix the issue by reconfiguring autonegotiation after PHY reset in ksz9031_read_status(). Fixes: d2fd719bcb0e ("net/phy: micrel: Add workaround for bad autoneg") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2017-12-051-2/+4
|\ \ | |/ | | | | | | | | | | Small overlapping change conflict ('net' changed a line, 'net-next' added a line right afterwards) in flexcan.c Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: phy-micrel: check return code in flp center functionMax Uvarov2017-12-011-2/+4
| | | | | | | | | | | | | | Fix obvious typo that first return value is set but not checked. Signed-off-by: Max Uvarov <muvarov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: phy: remove generic settings for callbacks config_aneg and read_status ↵Heiner Kallweit2017-12-011-24/+0
|/ | | | | | | | | | | from drivers Remove generic settings for callbacks config_aneg and read_status from drivers. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2017-06-301-0/+2
|\ | | | | | | | | | | | | A set of overlapping changes in macvlan and the rocker driver, nothing serious. Signed-off-by: David S. Miller <davem@davemloft.net>
| * net/phy: micrel: configure intterupts after autoneg workaroundZach Brown2017-06-221-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The commit ("net/phy: micrel: Add workaround for bad autoneg") fixes an autoneg failure case by resetting the hardware. This turns off intterupts. Things will work themselves out if the phy polls, as it will figure out it's state during a poll. However if the phy uses only intterupts, the phy will stall, since interrupts are off. This patch fixes the issue by calling config_intr after resetting the phy. Fixes: d2fd719bcb0e ("net/phy: micrel: Add workaround for bad autoneg ") Signed-off-by: Zach Brown <zach.brown@ni.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2017-06-061-14/+28
|\ \ | |/ | | | | | | | | | | Just some simple overlapping changes in marvell PHY driver and the DSA core code. Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: phy: micrel: Restore led_mode and clk_sel on resumeLeonard Crestez2017-06-011-14/+28
| | | | | | | | | | | | | | | | | | | | | | | | These bits seem to be lost after a suspend/resume cycle so just set them again. Do this by splitting the handling of these bits into a function that is also called on resume. This patch fixes ethernet suspend/resume on imx6ul-14x14-evk boards. Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | phy: micrel: add Microchip KSZ 9477 Switch PHY supportWoojung Huh2017-05-311-0/+11
| | | | | | | | | | | | | | | | | | Adding Microchip 9477 Phy included in KSZ9477 Switch. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Woojung Huh <Woojung.Huh@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: phy: Remove residual magic from PHY driversAndrew Lunn2017-05-161-14/+13
|/ | | | | | | | | commit fa8cddaf903c ("net phylib: Remove unnecessary condition check in phy") removed the only place where the PHY flag PHY_HAS_MAGICANEG was checked. But it left the flag being set in the drivers. Remove the flag. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2017-04-261-11/+0
|\ | | | | | | Signed-off-by: David S. Miller <davem@davemloft.net>
| * Revert "phy: micrel: Disable auto negotiation on startup"David S. Miller2017-04-261-11/+0
| | | | | | | | | | | | | | | | | | | | This reverts commit 99f81afc139c6edd14d77a91ee91685a414a1c66. It was papering over the real problem, which is fixed by commit f555f34fdc58 ("net: phy: fix auto-negotiation stall due to unavailable interrupt") Signed-off-by: David S. Miller <davem@davemloft.net>
* | Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2017-04-201-15/+2
|\ \ | |/ | | | | | | | | | | A function in kernel/bpf/syscall.c which got a bug fix in 'net' was moved to kernel/bpf/verifier.c in 'net-next'. Signed-off-by: David S. Miller <davem@davemloft.net>
| * net: phy: micrel: fix crash when statistic requested for KSZ9031 phyGrygorii Strashko2017-04-171-15/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Now the command: ethtool --phy-statistics eth0 will cause system crash with meassage "Unable to handle kernel NULL pointer dereference at virtual address 00000010" from: (kszphy_get_stats) from [<c069f1d8>] (ethtool_get_phy_stats+0xd8/0x210) (ethtool_get_phy_stats) from [<c06a0738>] (dev_ethtool+0x5b8/0x228c) (dev_ethtool) from [<c06b5484>] (dev_ioctl+0x3fc/0x964) (dev_ioctl) from [<c0679f7c>] (sock_ioctl+0x170/0x2c0) (sock_ioctl) from [<c02419d4>] (do_vfs_ioctl+0xa8/0x95c) (do_vfs_ioctl) from [<c02422c4>] (SyS_ioctl+0x3c/0x64) (SyS_ioctl) from [<c0107d60>] (ret_fast_syscall+0x0/0x44) The reason: phy_driver structure for KSZ9031 phy has no .probe() callback defined. As result, struct phy_device *phydev->priv pointer will not be initializes (null). This issue will affect also following phys: KSZ8795, KSZ886X, KSZ8873MLL, KSZ9031, KSZ9021, KSZ8061, KS8737 Fix it by: - adding .probe() = kszphy_probe() callback to KSZ9031, KSZ9021 phys. The kszphy_probe() can be re-used as it doesn't do any phy specific settings. - removing statistic callbacks from other phys (KSZ8795, KSZ886X, KSZ8873MLL, KSZ8061, KS8737) as they doesn't have corresponding statistic counters. Fixes: 2b2427d06426 ("phy: micrel: Add ethtool statistics counters") Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | net: phy: convert micrel to new read_mmd/write_mmd driver methodsRussell King2017-03-221-7/+6
|/ | | | | | | | | | Convert micrel to the new read_mmd/write_mmd driver methods. This Clause 22 PHY does not support any MMD access method. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: micrel: KSZ8795 do not set SUPPORTED_[Asym_]PauseSean Nyekjaer2017-01-291-1/+1
| | | | | | | | | | As pr commit "net: phy: phy drivers should not set SUPPORTED_[Asym_]Pause" this phy driver should not set these feature bits. Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk> Fixes: 9d162ed69f51 ("net: phy: micrel: add support for KSZ8795") Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: micrel: add support for KSZ8795Sean Nyekjaer2017-01-271-0/+14
| | | | | | | | | | This is adds support for the PHYs in the KSZ8795 5port managed switch. It will allow to detect the link between the switch and the soc and uses the same read_status functions as the KSZ8873MLL switch. Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: phy drivers should not set SUPPORTED_[Asym_]PauseTimur Tabi2016-12-101-18/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Instead of having individual PHY drivers set the SUPPORTED_Pause and SUPPORTED_Asym_Pause flags, phylib itself should set those flags, unless there is a hardware erratum or other special case. During autonegotiation, the PHYs will determine whether to enable pause frame support. Pause frames are a feature that is supported by the MAC. It is the MAC that generates the frames and that processes them. The PHY can only be configured to allow them to pass through. This commit also effectively reverts the recently applied c7a61319 ("net: phy: dp83848: Support ethernet pause frames"). So the new process is: 1) Unless the PHY driver overrides it, phylib sets the SUPPORTED_Pause and SUPPORTED_AsymPause bits in phydev->supported. This indicates that the PHY supports pause frames. 2) The MAC driver checks phydev->supported before it calls phy_start(). If (SUPPORTED_Pause | SUPPORTED_AsymPause) is set, then the MAC driver sets those bits in phydev->advertising, if it wants to enable pause frame support. 3) When the link state changes, the MAC driver checks phydev->pause and phydev->asym_pause, If the bits are set, then it enables the corresponding features in the MAC. The algorithm is: if (phydev->pause) The MAC should be programmed to receive and honor pause frames it receives, i.e. enable receive flow control. if (phydev->pause != phydev->asym_pause) The MAC should be programmed to transmit pause frames when needed, i.e. enable transmit flow control. Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: micrel: fix KSZ8041FTL supported valueKirill Esipov2016-11-231-4/+4
| | | | | | | | Fix setting of SUPPORTED_FIBRE bit as it was not present in features of KSZ8041. Signed-off-by: Kirill Esipov <yesipov@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* phy: micrel.c: Enable ksz9031 energy-detect power-down modeMike Looijmans2016-10-051-0/+21
| | | | | | | | | | | Set bit 0 in register 1C.23 to enable the EDPD feature of the KSZ9031 PHY. This reduces power consumption when the link is down. Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com Signed-off-by: David S. Miller <davem@davemloft.net>
* phy: micrel: Reenable interrupts during resume for ksz9031Xander Huff2016-08-231-1/+1
| | | | | | | | | | | Like the ksz8081, the ksz9031 has the behavior where it will clear the interrupt enable bits when leaving power down. This takes advantage of the solution provided by f5aba91. Signed-off-by: Xander Huff <xander.huff@ni.com> Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: micrel: Add specific suspendWenyou Yang2016-08-091-8/+19
| | | | | | | | | | Disable all interrupts when suspend, they will be enabled when resume. Otherwise, the suspend/resume process will be blocked occasionally. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* phy/micrel: Change phy_id_mask for KSZ8721Alexander Stein2016-07-311-2/+2
| | | | | | | | | There are KSZ8721 PHYs with phy_id 0x00221619. In order to detect them as PHY_ID_KSZ8001 compatible while staying different to PHY_ID_KSZ9021 ignore the last two bits when matching PHY_ID Signed-off-by: Alexander Stein <alexanders83@web.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: micrel: Add KSZ8041FTL fiber mode supportPhilipp Zabel2016-07-151-2/+32
| | | | | | | | | | We can't detect the FXEN (fiber mode) bootstrap pin, so configure it via a boolean device tree property "micrel,fiber-mode". If it is enabled, auto-negotiation is not supported. The only available modes are 100base-fx (full duplex and half duplex). Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
* phy: micrel: Use MICREL_PHY_ID_MASK definitionFabio Estevam2016-05-121-17/+17
| | | | | | | | | | | Replace the hardcoded mask 0x00fffff0 with MICREL_PHY_ID_MASK for better readability. Suggested-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2016-03-081-1/+27
|\ | | | | | | | | | | | | | | Several cases of overlapping changes, as well as one instance (vxlan) of a bug fix in 'net' overlapping with code movement in 'net-next'. Signed-off-by: David S. Miller <davem@davemloft.net>
| * phy: micrel: Disable auto negotiation on startupAlexandre Belloni2016-03-011-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Disable auto negotiation on init to properly detect an already plugged cable at boot. At boot, when the phy is started, it is in the PHY_UP state. However, if a cable is plugged at boot, because auto negociation is already enabled at the time we get the first interrupt, the phy is already running. But the state machine then switches from PHY_UP to PHY_AN and calls phy_start_aneg(). phy_start_aneg() will not do anything because aneg is already enabled on the phy. It will then wait for a interrupt before going further. This interrupt will never happen unless the cable is unplugged and then replugged. It was working properly before 321beec5047a (net: phy: Use interrupts when available in NOLINK state) because switching to NOLINK meant starting polling the phy, even if IRQ were enabled. Fixes: 321beec5047a (net: phy: Use interrupts when available in NOLINK state) Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
| * phy: micrel: Ensure interrupts are reenabled on resumeAlexandre Belloni2016-03-011-1/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | At least on ksz8081, when getting back from power down, interrupts are disabled. ensure they are reenabled if they were previously enabled. This fixes resuming which is failing on the xplained boards from atmel since 321beec5047a (net: phy: Use interrupts when available in NOLINK state) Fixes: 321beec5047a (net: phy: Use interrupts when available in NOLINK state) Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | phy: marvell/micrel: Fix Unpossible conditionAndrew Lunn2016-02-191-4/+5
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | commit 2b2427d06426 ("phy: micrel: Add ethtool statistics counters") from Dec 30, 2015, leads to the following static checker warning: drivers/net/phy/micrel.c:609 kszphy_get_stat() warn: unsigned 'val' is never less than zero. drivers/net/phy/micrel.c 602 static u64 kszphy_get_stat(struct phy_device *phydev, int i) 603 { 604 struct kszphy_hw_stat stat = kszphy_hw_stats[i]; 605 struct kszphy_priv *priv = phydev->priv; 606 u64 val; 607 608 val = phy_read(phydev, stat.reg); 609 if (val < 0) { ^^^^^^^ Unpossible! 610 val = UINT64_MAX; 611 } else { 612 val = val & ((1 << stat.bits) - 1); 613 priv->stats[i] += val; 614 val = priv->stats[i]; 615 } 616 617 return val; 618 } The same problem exists in the Marvell driver. Fix both. Fixes: 2b2427d06426 ("phy: micrel: Add ethtool statistics counters") Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Reported-by: Julia.Lawall <julia.lawall@lip6.fr> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller2016-01-111-2/+10
|\ | | | | | | | | | | | | | | | | | | | | | | Conflicts: drivers/net/bonding/bond_main.c drivers/net/ethernet/mellanox/mlxsw/spectrum.h drivers/net/ethernet/mellanox/mlxsw/spectrum_switchdev.c The bond_main.c and mellanox switch conflicts were cases of overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
| * phy: micrel: Fix finding PHY properties in MAC node for KSZ9031.Roosen Henri2016-01-081-2/+10
| | | | | | | | | | | | | | | | | | | | | | Commit 651df2183543 ("phy: micrel: Fix finding PHY properties in MAC node.") only fixes finding PHY properties in MAC node for KSZ9021. This commit applies the same fix for KSZ9031. Fixes: 8b63ec1837fa ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.") Acked-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Henri Roosen <henri.roosen@ginzinger.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | phy: Centralize setting driver module ownerAndrew Lunn2016-01-071-13/+0
| | | | | | | | | | | | | | | | | | | | Rather than have each driver set the driver owner field, do it once in the core code. This will also help with later changes, when the device structure will move. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | phy: Add an mdio_device structureAndrew Lunn2016-01-071-6/+6
| | | | | | | | | | | | | | | | | | Not all devices attached to an MDIO bus are phys. So add an mdio_device structure to represent the generic parts of an mdio device, and place this structure into the phy_device. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
* | phy: Add phydev_err() and phydev_dbg() macrosAndrew Lunn2016-01-071-7/+9
| | | | | | | | | | | | | | | | | | In preparation for moving some of the phy_device structure members, add macros for printing errors and debug information. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* | phy: micrel: Add ethtool statistics countersAndrew Lunn2015-12-311-0/+96
|/ | | | | | | | The PHY counters receiver errors and errors while idle. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* phy: micrel: Fix finding PHY properties in MAC node.Andrew Lunn2015-12-111-2/+11
| | | | | | | | | | | | | | | | | | | | commit 8b63ec1837fa ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.") changed the parenting of PHY devices, making them a child of the MDIO bus, instead of the MAC device. This broken the Micrel PHY driver which has a deprecated feature of allowing PHY properties to be placed into the MAC node. In order to find the MAC node, we need to walk up the tree of devices until we find one with an OF node attached. Reported-by: Dinh Nguyen <dinguyen@opensource.altera.com> Suggested-by: David Daney <david.daney@cavium.com> Acked-by: David Daney <david.daney@cavium.com> Fixes: 8b63ec1837fa ("phylib: Make PHYs children of their MDIO bus, not the bus' parent.") Signed-off-by: Andrew Lunn <andrew@lunn.ch> Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/phy: micrel: Add workaround for bad autonegNathan Sullivan2015-10-231-1/+22
| | | | | | | | | | Very rarely, the KSZ9031 will appear to complete autonegotiation, but will drop all traffic afterwards. When this happens, the idle error count will read 0xFF after autonegotiation completes. Reset the PHY when in that state. Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/phy: micrel: Center FLP timing at 16msJaeden Amero2015-06-081-1/+22
| | | | | | | | | | | | | | | | | | | | | | | Link failures have been observed when using the KSZ9031 with HP 1810-8G and HP 1910-8G network switches. Center the FLP timing at 16ms to help avoid intermittent link failures. >From the KSZ9031RNX and KSZ9031MNX data sheets revision 2.2, section "Auto-Negotiation Timing": The KSZ9031[RNX or MNX] Fast Link Pulse (FLP) burst-to-burst transmit timing for Auto-Negotiation defaults to 8ms. IEEE 802.3 Standard specifies this timing to be 16ms +/-8ms. Some PHY link partners need to receive the FLP with 16ms centered timing; otherwise, there can be intermittent link failures and long link-up times. The PHY data sheet recommends configuring the FLP burst registers after power-up/reset and immediately thereafter restarting auto-negotiation, so we center the FLP timing at 16ms and then restart auto-negotiation in the config_init for KSZ9031. Signed-off-by: Jaeden Amero <jaeden.amero@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/phy: micrel: Comment MMD address of extended registersJaeden Amero2015-06-081-0/+1
| | | | | | | | There are some defines for a few pad skew related extended registers. Specify for which MMD Address (dev_addr) they are for. Signed-off-by: Jaeden Amero <jaeden.amero@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net/phy: micrel: Be more const correctJaeden Amero2015-06-081-14/+15
| | | | | | | | | | | In a few places in this driver, we weren't using const where we could have. Use const more. In addition, change the arrays of strings in ksz9031_config_init() to be not only const, but also static. Signed-off-by: Jaeden Amero <jaeden.amero@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: micrel: Fix regression in kszphy_probeNiklas Cassel2015-05-121-1/+2
| | | | | | | | | | | | | | | | | | | | Don't do clock-mode-select if clk == NULL, since when building without CONFIG_HAVE_CLK, clk_get returns NULL and clk_get_rate returns 0. Doing clock-mode-select in this cause causes kszphy_probe to return -EINVAL and thus prevents the device from being probed. The original code (before regression) would return 0 when building without CONFIG_HAVE_CLK. Cc: stable <stable@vger.kernel.org> # 3.18+ Fixes: 1fadee0c3645 ("net/phy: micrel: Add clock support for KSZ8021/KSZ8031") Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com> Reviewed-by: Johan Hovold <johan@kernel.org> Signed-off-by: Niklas Cassel <niklass@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: micrel: disable NAND-tree for KSZ8021, KSZ8031, KSZ8051, KSZ8081Sylvain Rochet2015-02-141-0/+28
| | | | | | | | | | | | | | | | | | NAND-tree is used to check wiring between MAC and PHY using NAND gates on the PHY side, hence the name. NAND-tree initial status is latched at reset by probing the IRQ pin. However some devices are sharing the PHY IRQ pin with other peripherals such as Atmel SAMA5D[34]x-EK boards when using the optional TM7000 display module, therefore they are switching the PHY in NAND-tree test mode depending on the current IRQ line status at reset. This patch ensure PHY is not in NAND-tree test mode for all Micrel PHYs using IRQ line as a NAND-tree toggle mode at reset. Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: micrel: use generic config_init for KSZ8021/KSZ8031Johan Hovold2014-12-261-15/+3
| | | | | | | | | | | | | | | | | Use generic config_init callback also for KSZ8021 and KSZ8031. This has been avoided this far due to commit b838b4aced99 ("phy/micrel: KSZ8031RNL RMII clock reconfiguration bug"), which claims that the PHY becomes unresponsive if the broadcast-disable flag is set before configuring the clock mode. Turns out that the problem seemingly worked-around by the above mentioned commit was really due to a hardware-configuration issue, where the PHY was in fact strapped to address 3 rather than 0. Tested-by: Bruno Thomsen <bth@kamstrup.dk> Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: micrel: add copyright entryJohan Hovold2014-11-211-0/+1
| | | | | | | Add myself to the list of copyright holders. Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: micrel: refactor interrupt configJohan Hovold2014-11-211-42/+29
| | | | | | | | Add generic interrupt-config callback and store interrupt-level bitmask in type data for PHY types not using bit 9. Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
* net: phy: micrel: add support for clock-mode select to KSZ8081/KSZ8091Johan Hovold2014-11-211-5/+6
| | | | | | | | | | | | | Micrel KSZ8081 and KSZ8091 PHYs have the RMII Reference Clock Select bit, which is used to select 25 or 50 MHz clock mode. Note that on some revisions of the PHY (e.g. KSZ8081RND) the function of this bit is inverted so that setting it enables 25 rather than 50 MHz mode. Add a new device-tree property "micrel,rmii-reference-clock-select-25-mhz" to describe this. Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
OpenPOWER on IntegriCloud