| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| ... | |
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Enable i40e to pass traffic with VLAN tags using the 802.1ad ethernet
protocol ID (0x88a8).
This requires NIC firmware providing version 1.7 of the API. With
older NIC firmware 802.1ad tagged packets will continue to be dropped.
No VLAN offloads nor RSS are supported for 802.1ad VLANs.
Signed-off-by: Scott Peterson <scott.d.peterson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Currently there is a bug in which the PF driver fails to inform clients
of a VF reset which then causes clients to leak resources. The bug
exists because we were incorrectly checking the I40E_VF_STATE_PRE_ENABLE
bit.
When a VF is first init we go through a reset to initialize variables
and allocate resources but we don't want to inform clients of this first
reset since the client isn't fully enabled yet so we set a state bit
signifying we're in a "pre-enabled" client state. During the first
reset we should be clearing the bit, allowing all following resets to
notify the client of the reset when the bit is not set. This patch
fixes the issue by negating the 'test_and_clear_bit' check to accurately
reflect the behavior we want.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Currently we inappropriately clear the vf_states variable with a null
assignment. This is problematic because we should be using atomic
bitops on this variable and we don't actually want to clear all the
flags. We should just clear the ones we know we want to clear.
Additionally remove the I40E_VF_STATE_FCOEENA bit because it is no
longer being used.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
This function cannot fail, so why is it returning a value? And why are
we checking it? Why shouldn't we just make it void? Why is this commit
message made up of only questions?
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Currently the VF gets a default number of allocated queues from HW on
init and it could choose to enable or disable those allocated queues.
This makes it such that the VF can request more or less underlying
allocated queues from the PF.
First the VF negotiates the number of queues it wants that can be
supported by the PF and if successful asks for a reset. During reset
the PF will reallocate the HW queues for the VF and will then remap the
new queues.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
It is possible although rare that we may not reset when
i40e_vc_disable_vf() is called. This can lead to some weird
circumstances with some values not being properly set. Modify
i40e_reset_vf() to return a code indicating whether it reset or not.
Now, i40e_vc_disable_vf() can wait until a reset actually occurs. If it
fails to free up within a reasonable time frame we'll display a warning
message.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Replace i40e_vc_notify_vf_reset and i40e_reset_vf with a call to
i40e_vc_disable_vf which does this exact thing. This matches similar
code patterns throughout the driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
It's never used, and the vf structure could get back to the PF if
necessary. Lets just drop the extra unneeded parameter.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
When we refactored handling of the PVID in commit 9af52f60b2d9
("i40e: use (add|rm)_vlan_all_mac helper functions when changing PVID")
we introduced a scheduling while atomic regression.
This occurred because we now held the spinlock across a call to
i40e_reset_vf(), which results in a usleep_range() call that triggers
a scheduling while atomic bug. This was rare as it only occurred if the
user configured a VLAN on a VF and also attempted to reconfigure the VF
from the host system with a port VLAN.
We do need to hold the lock while calling i40e_is_vsi_in_vlan(), but we
should not be holding it while we reset the VF.
We'll fix this by introducing a separate helper function
i40e_vsi_has_vlans which checks whether we have a PVID and whether the
VSI has configured VLANs. This helper function will manage its own need
for the mac_filter_hash_lock.
Then, we can move the acquiring of the spinlock until after we reset the
VF, which ensures that we do not sleep while holding the lock.
Using a separate function like this makes the code more clear and is
easier to read than attempting to release and re-acquire the spinlock
when we reset the VF.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Instead of accessing register directly, use newly added AQC in
order to blink LEDs. Introduce and utilize a new flag to prevent
excessive API version checking.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
This patch adds support for 'ethtool -m' command which displays
information about (Q)SFP+ module plugged into NIC's cage.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
This patch fixes incorrect reporting of supported link modes on some NICs.
Signed-off-by: Filip Sadowski <filip.sadowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
If 'kzalloc()' fails, a NULL pointer will be dereferenced.
Return an error code (-ENOMEM) instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
This patch removes the !vf condition check that cannot be
true in i40e_ndo_set_vf_trust function
Detected by CoverityScan, CID 1397531 Logically dead code
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
When a machine has more CPUs than queue pairs, e.g. 512 cores, the
counting gets a little funky and turns off Flow Director with the
message:
not enough queues for Flow Director. Flow Director feature is disabled
This patch limits the number of lan queues initially allocated to
be sure we have some left for FD and other features.
Signed-off-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Although very unlikely, it is possible that cancel_work_sync() may stop
the service_task before it actually started. In this case, the
__FM10K_SERVICE_SCHED bit will never be cleared. This results in the
service task being unable to reschedule in the future. Add a helper
function which sets the service disable bit, waits for the service task
to stop and clears the schedule bit, thus avoiding the race condition.
We know the schedule bit is safe to clear because the cancel_work_sync()
guarantees the service task is not running.
Add a helper function also to restart the service task, for symmetry.
This is not strictly needed but helps the mental model of how to stop
and start the service task.
This race could only happen in fm10k_suspend/fm10k_resume as this is the
only place where the service task is actually restarted. Thus,
suspend/resume testing would be ideal. However, note that the chance of
this happening is very slim as the service event is scheduled for
immediate execution, and you would have to trigger a suspend at almost
the exact same time as the service task was scheduled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
A future patch needs these functions defined earlier in the file. Move
them closer to above where they will be called.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
It is possible that under rare circumstances the device is undergoing
a reset, such as when a PFLR occurs, and the device may be transmitting
simultaneously. In this case, we might attempt to divide by zero when
finding the proper r_idx. Instead, lets read the num_tx_queues once,
and make sure it's non-zero.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
We've always had a really weird looping construction for resetting VFs.
We read the VFLRE register and reset the VF if the corresponding bit is
set, which makes sense. However we loop continuously until we no longer
have any bits left unset. At first this makes sense, as a sort of "keep
trying until we succeed" concept.
Unfortunately this causes a problem if we happen to surprise remove
while this code is executing, because in this case we'll always read all
1s for the VFLRE register. This results in a hard lockup on the CPU
because the loop will never terminate.
Because our own reset function will clear the VFLR event register
always, (except when we've lost PCIe link obviously) there is no real
reason to loop. In practice, we'll loop over once and find that no VFs
are pending anymore.
Lets just check once. Since we're clear the notification when we reset
there's no benefit to the loop. Additionally, there shouldn't be a race
as future VLFRE events should trigger an interrupt. Additionally, we
didn't warn or do anything in the looped case anyways.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
We're doing a really convoluted bitshift and read for the PFVFLRE
register. Just reading the PFVFLRE(1), shifting it by 32, then reading
PFVFLRE(0) should be sufficient.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
When we load the driver, we set the last_reset to be in the future,
which delays the initial driver reset. Additionally, the service task
isn't scheduled to run automatically until the timer runs out. This
causes a needless delay of the first reset to begin talking to the
switch manager.
We can avoid this by simply not setting last_reset and immediately
scheduling the service task while in probe. This allows the device to
wake up faster, and avoids this delay.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Newer versions of GCC starting with 7 now additionally warn when a case
statement may fall through without an explicit comment mentioning it.
Add such a comment to silence the warning, as this is expected.
Unfortunately the comment must come directly before the next case
statement, so we put it outside the #ifdef. Otherwise, the compiler
cannot properly detect it and thus the warning is displayed regardless.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
New versions of GCC since version 7 began warning about possible
truncation of calls to snprintf. We can fix this and avoid false
positives. First, we should pass the full buffer size to snprintf,
because it guarantees a NULL character as part of its passed length, so
passing len-1 is simply wasting a byte of possible storage.
Second, if we make the ri and ti variables unsigned, the compiler is
able to correctly reason that the value never gets larger than 256, so
it doesn't need to warn about the full space required to print a signed
integer.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Newer versions of GCC since version 7 now warn when a case statement may
fall through without an explicit comment. "Fallthough" does not count as
it is misspelled. Fix the typos for these comments to appease the new
warnings.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
In fm10k_get_host_state_generic, we check the mailbox tx_read() function
to ensure that the mailbox is still open. This function also checks to
make sure we have space to transmit another message. Unfortunately, if
we just recently sent a bunch of messages (such as enabling hundreds of
VLANs on a VF) this can result in a race where the watchdog task thinks
the link went down just because we haven't had time to process all these
messages yet.
Instead, lets just check whether the mailbox is still open. This ensures
that we don't race with the Tx FIFO, and we only link down once the
mailbox is not open.
This is safe, because if the FIFO fills up and we're unable to send
a message for too long, we'll end up triggering the timeout detection
which results in a reset. Additionally, since we still check to ensure
the mailbox state is OPEN, we'll transition to link down whenever the
mailbox closes as well.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
Two single characters should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | |
| | | | | | | |
When we are handling PF<->VF mailbox messages, it is possible that the
VF will send us so many messages that the PF<->SM FIFO will fill up. In
this case, we stop the loop and wait until the service event is
rescheduled.
Normally this should happen due to an interrupt. But it is possible that
we don't get another interrupt for a while and it isn't until the
service timer actually reschedules us. Instead, simply reschedule
immediately which will cause the service event to be run again as soon
as we exit.
This ensures that we promptly handle all of the PF<->VF messages with
minimal delay, while still giving time for the SM mailbox to drain.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | |/ / / / /
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
When we process VF mailboxes, the driver is likely going to also queue
up messages to the switch manager. This process merely queues up the
FIFO, but doesn't actually begin the transmission process. Because we
hold the mailbox lock during this VF processing, the PF<->SM mailbox is
not getting processed at this time. Ensure that we actually process the
PF<->SM mailbox in between each PF<->VF mailbox.
This should ensure prompt transmission of the messages queued up after
each VF message is received and handled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The i40e driver now supports two different devices with two different
firmware versions. So be smart about how we handle these. Move the FW
version macros to the appropriate header file, and add a convenience
macro that checks the version based on the device. Then use this macro
to check whether or not the driver can use the new link info API.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Currently the PF allocates a default number of queues for each VF and
cannot be changed. This patch enables the VF to request a different
number of queues allocated to it. This patch also adds a new virtchnl
op and capability flag to facilitate this negotiation.
After the PF receives a request message, it will set a requested number
of queues for that VF. Then when the VF resets, its VSI will get a new
number of queues allocated to it.
This is a best effort request and since we only allocate a guaranteed
default number, if the VF tries to ask for more than the guaranteed
number, there may not be enough in HW to accommodate it unless other
queues for other VFs are freed. It should also be noted decreasing the
number queues allocated to a VF to below the default will NOT enable the
allocation of more than 32 VFs per PF and will not free queues guaranteed
to each VF by default.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
The current implementation for mapping queues to vectors is broken
because it attempts to map each Tx and Rx ring to its own vector,
however we use combined queues so we should actually be mapping the
Tx/Rx rings together on one vector.
Also in the current implementation, in the case where we have more
queues than vectors, we attempt to group the queues together into
'chunks' and map each 'chunk' of queues to a vector. Chunking them
together would be more ideal if, and only if, we only had RSS because of
the way the hashing algorithm works but in the case of a future patch
that enables VF ADq, round robin assignment is better and still works
with RSS.
This patch resolves both those issues and simplifies the code needed to
accomplish this. Instead of treating the case where we have more queues
than vectors as special, if we notice our vector index is greater than
vectors, reset the vector index to zero and continue mapping. This
should ensure that in both cases, whether we have enough vectors for
each queue or not, the queues get appropriately mapped.
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
On some platforms with a large number of CPUs, we will allocate many IRQ
vectors. When hibernating, the system will attempt to migrate all of the
vectors back to CPU0 when shutting down all the other CPUs. It is
possible that we have so many vectors that it cannot re-assign them to
CPU0. This is even more likely if we have many devices installed in one
platform.
The end result is failure to hibernate, as it is not possible to
shutdown the CPUs. We can avoid this by disabling MSI-X and clearing our
interrupt scheme when the device is suspended. A more ideal solution
would be some method for the stack to properly handle this for all
drivers, rather than on a case-by-case basis for each driver to fix
itself.
However, until this more ideal solution exists, we can do our part and
shutdown our IRQs during suspend, which should allow systems with
a large number of CPUs to safely suspend or hibernate.
It may be worth investigating if we should shut down even further when
we suspend as it may make the path cleaner, but this was the minimum fix
for the hibernation issue mentioned here.
Testing-hints:
This affects systems with a large number of CPUs, and with multiple
devices enabled. Without this change, those platforms are unable to
hibernate at all.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Although the service task does check the suspended status before
running, it might already be part way through running when we go to
suspend. Lets ensure that the service task is stopped and will not be
restarted again until we finish resuming. This ensures that service task
code does not cause strange interactions with the suspend/resume
handlers.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
When handling suspend and resume callbacks we want to make sure that (a)
we don't suspend again if we're already suspended and (b) we don't
resume again if we're already resuming. Lets make sure we test_and_set
the __I40E_SUSPENDED bit in i40e_suspend which ensures that a suspend
call when already suspended will exit early. Additionally, if
__I40E_SUSPENDED is not set when we begin resuming, exit early as well.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Stop using the old legacy PM support, since we now have stable support
for the newer generic PM callbacks.
This has several advantages. First, we no longer have to manage our
own pci_save_state() and power changes, as it's preferred to have the
PCI stack do this. Second, these routines get called for both hibernate
and suspend to ram, so we can have the driver properly handle all the
suspend/resume flows that it needs to.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
We currently (mis)use the __I40E_RECOVERY_PENDING bit to determine when
we should actually request a new IRQ in i40e_setup_misc_vector().
This led to a design mistake where we open-coded the re-setup of the
miscellaneous vector in i40e_resume() instead of using the function
provided. If we did not open-code this and instead tried to use the
i40e_setup_misc_vector() function, it would lead to never reallocating
the IRQ.
This would lead to a second i40e_suspend() call failing to free the
vector due to a NULL pointer dereference.
A future patch is going to re-work how the i40e_suspend() and
i40e_resume() flows work to clear all IRQ vectors, which would require
us to use i40e_setup_misc_vector() directly. Since during this time the
__I40E_RECOVERY_PENDING bit is set, we'll never re-allocate the vector.
Rather than leaving the open-coded setup in i40e_resume() lets just fix
the problem properly in i40e_setup_misc_vector().
Introduce a new state bit which indicates when the IRQ has been
assigned, which will be set when i40e_setup_misc_vector is first called.
This ultimately resolves the issue of re-requesting the vector, without
overloading the __I40E_RECOVERY_PENDING state. This ensures that the
suspend/resume cycle can use the setup function instead of open-coding
the re-request during resume.
Additionally, since the only callers of i40e_stop_misc_vector also want
to free it, move this code directly into the function to avoid
duplication. Due to the new functionality, rename it to
i40e_free_misc_vector().
This lets us drop the extra calls to free and re-enable the vector
during i40e_suspend() and i40e_resume(). We don't need to call
i40e_setup_misc_Vector() in i40e_resume() because it gets called by the
i40e_rebuild() call.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
We see this message regularly on VF reset or unload (which invokes a
reset). It's essentially meaningless unless it's happening constantly.
To prevent consternation, lower the log level to debug so it's not seen
under normal circumstance.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
An errata with GLQF_PCNT causes it to not wrap as expected. This
can cause an error in flow director statistics. This patch resets
affected counters just after reading.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Fortville and Fort Park devices are often on different firmware release
schedules. This change relaxes the minor version warning message,
so it is only displayed for older FW warning version for old
firmware Fortville 3 or earlier.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
This commit replaces usage of vsi->back in i40e_print_link_message()
(which is actually a PF pointer) with temp variable.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
i40e_print_link_message() is intended to compare new
link state with current link state and print log message
only if the new state is different from current state.
However in current driver the new state does not get updated
when link is going down because of the if condition. When an
interface is brought down, vsi->state is set to I40E_VSI_DOWN
in i40e_vsi_close() and later i40e_print_link_message() does
not get invoked in i40e_link_event due to if condition. Hence
link down message doesn't appear when link is going down. The
down state is seen later during i40e_open() and old state
gets printed. The actual link state doesn't get updated in
i40e_close() or i40e_open() but when i40e_handle_link_event is
called inside i40e_clean_adminq_subtask.
This change allows i40e_print_link_message() to be called when
interface is going down and keeps the state information updated.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
In current driver, when ifconfig ethx up is done, the link state
doesn't transition to UP inside i40e_open(). It changes after AQ
command response is handled in i40e_handle_link_event().
When pf->hw.phy.link_info.link_info is DOWN inside i40e_open(),
The state is transient and invalid. So log message gets printed
based on incorrect info (i.e link_info and an_info).
This commit removes check for unqualified module inside
i40e_up_complete(). The existing check in i40e_handle_link_event()
logs the error message based on correct link state information.
Signed-off-by: Sudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
This value is not calculating bytes_per_int, which would actually just
be bytes/ITR_COUNTDOWN_START, but rather it's calculating bytes/usecs.
Rename the variable for clarity so that future developers understand
what the value is actually calculating.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Implement support for transferring XDP meta data into skb for
ixgbe driver; before calling into the program, xdp.data_meta points
to xdp.data, where on program return with pass verdict, we call
into skb_metadata_set().
We implement this for the default ixgbe_build_skb() variant. For the
ixgbe_construct_skb() that is used when legacy-rx buffer mananagement
mode is turned on via ethtool, I found that XDP gets 0 headroom, so
neither xdp_adjust_head() nor xdp_adjust_meta() can be used with this.
Just add a comment with explanation for this operating mode.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
This work enables generic transfer of metadata from XDP into skb. The
basic idea is that we can make use of the fact that the resulting skb
must be linear and already comes with a larger headroom for supporting
bpf_xdp_adjust_head(), which mangles xdp->data. Here, we base our work
on a similar principle and introduce a small helper bpf_xdp_adjust_meta()
for adjusting a new pointer called xdp->data_meta. Thus, the packet has
a flexible and programmable room for meta data, followed by the actual
packet data. struct xdp_buff is therefore laid out that we first point
to data_hard_start, then data_meta directly prepended to data followed
by data_end marking the end of packet. bpf_xdp_adjust_head() takes into
account whether we have meta data already prepended and if so, memmove()s
this along with the given offset provided there's enough room.
xdp->data_meta is optional and programs are not required to use it. The
rationale is that when we process the packet in XDP (e.g. as DoS filter),
we can push further meta data along with it for the XDP_PASS case, and
give the guarantee that a clsact ingress BPF program on the same device
can pick this up for further post-processing. Since we work with skb
there, we can also set skb->mark, skb->priority or other skb meta data
out of BPF, thus having this scratch space generic and programmable
allows for more flexibility than defining a direct 1:1 transfer of
potentially new XDP members into skb (it's also more efficient as we
don't need to initialize/handle each of such new members). The facility
also works together with GRO aggregation. The scratch space at the head
of the packet can be multiple of 4 byte up to 32 byte large. Drivers not
yet supporting xdp->data_meta can simply be set up with xdp->data_meta
as xdp->data + 1 as bpf_xdp_adjust_meta() will detect this and bail out,
such that the subsequent match against xdp->data for later access is
guaranteed to fail.
The verifier treats xdp->data_meta/xdp->data the same way as we treat
xdp->data/xdp->data_end pointer comparisons. The requirement for doing
the compare against xdp->data is that it hasn't been modified from it's
original address we got from ctx access. It may have a range marking
already from prior successful xdp->data/xdp->data_end pointer comparisons
though.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Use *_pool_zalloc rather than *_pool_alloc followed by memset with 0.
Found by coccinelle spatch "api/alloc/pool_zalloc-simple.cocci"
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| | | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
| |\ \ \ \ \ \
| | |_|_|_|/
| |/| | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | |
| | | | | | |
Conflicts:
include/linux/compiler-clang.h
include/linux/compiler-gcc.h
include/linux/compiler-intel.h
include/uapi/linux/stddef.h
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
