| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Avoid that the following complaint is reported:
BUG: sleeping function called from invalid context at kernel/workqueue.c:2790
in_atomic(): 1, irqs_disabled(): 0, pid: 41, name: rcuop/3
1 lock held by rcuop/3/41:
#0: (rcu_callback){......}, at: [<ffffffff8111f9a2>] rcu_nocb_kthread+0x282/0x500
Call Trace:
dump_stack+0x86/0xcf
___might_sleep+0x174/0x260
__might_sleep+0x4a/0x80
flush_work+0x7e/0x2e0
__cancel_work_timer+0x143/0x1c0
cancel_work_sync+0x10/0x20
blk_throtl_exit+0x25/0x60
blkcg_exit_queue+0x35/0x40
blk_release_queue+0x42/0x130
kobject_put+0xa9/0x190
This happens since we invoke callbacks that need to block from the
queue release handler. Fix this by pushing the final release to
a workqueue.
Reported-by: Ross Zwisler <zwisler@gmail.com>
Fixes: commit b425e5049258 ("block: Avoid that blk_exit_rl() triggers a use-after-free")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Tested-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Updated changelog
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Since the introduction of .init_rq_fn() and .exit_rq_fn() it is
essential that the memory allocated for struct request_queue
stays around until all blk_exit_rl() calls have finished. Hence
make blk_init_rl() take a reference on struct request_queue.
This patch fixes the following crash:
general protection fault: 0000 [#2] SMP
CPU: 3 PID: 28 Comm: ksoftirqd/3 Tainted: G D 4.12.0-rc2-dbg+ #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.0.0-prebuilt.qemu-project.org 04/01/2014
task: ffff88013a108040 task.stack: ffffc9000071c000
RIP: 0010:free_request_size+0x1a/0x30
RSP: 0018:ffffc9000071fd38 EFLAGS: 00010202
RAX: 6b6b6b6b6b6b6b6b RBX: ffff880067362a88 RCX: 0000000000000003
RDX: ffff880067464178 RSI: ffff880067362a88 RDI: ffff880135ea4418
RBP: ffffc9000071fd40 R08: 0000000000000000 R09: 0000000100180009
R10: ffffc9000071fd38 R11: ffffffff81110800 R12: ffff88006752d3d8
R13: ffff88006752d3d8 R14: ffff88013a108040 R15: 000000000000000a
FS: 0000000000000000(0000) GS:ffff88013fd80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa8ec1edb00 CR3: 0000000138ee8000 CR4: 00000000001406e0
Call Trace:
mempool_destroy.part.10+0x21/0x40
mempool_destroy+0xe/0x10
blk_exit_rl+0x12/0x20
blkg_free+0x4d/0xa0
__blkg_release_rcu+0x59/0x170
rcu_process_callbacks+0x260/0x4e0
__do_softirq+0x116/0x250
smpboot_thread_fn+0x123/0x1e0
kthread+0x109/0x140
ret_from_fork+0x31/0x40
Fixes: commit e9c787e65c0c ("scsi: allocate scsi_cmnd structures as part of struct request")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jan Kara <jack@suse.cz>
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The code in blk-mq-debugfs.c assumes that it is working on a blk-mq
queue and is not intended to work on a blk-sq queue. Hence only
register blk-mq debugfs attributes for blk-mq queues.
Fixes: commit 9c1051aacde8 ("blk-mq: untangle debugfs and sysfs")
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Originally, I tied debugfs registration/unregistration together with
sysfs. There's no reason to do this, and it's getting in the way of
letting schedulers define their own debugfs attributes. Instead, tie the
debugfs registration to the lifetime of the structures themselves.
The saner lifetimes mean we can also get rid of the extra mq directory
and move everything one level up. I.e., nvme0n1/mq/hctx0/tags is now
just nvme0n1/hctx0/tags.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
|
|
|
|
| |
Preparation for adding more declarations.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
A later patch in this series will modify blk_mq_debugfs_register()
such that it uses q->kobj.parent to determine the name of a
request queue. Hence make sure that that pointer is initialized
before blk_mq_debugfs_register() is called. To avoid lock inversion,
protect sysfs / debugfs registration with the queue sysfs_lock
instead of the global mutex all_q_mutex.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
|
|
|
|
|
|
|
|
| |
When CFQ is used as an elevator, it disables writeback throttling
because they don't play well together. Later when a different elevator
is chosen for the device, writeback throttling doesn't get enabled
again as it should. Make sure CFQ enables writeback throttling (if it
should be enabled by default) when we switch from it to another IO
scheduler.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
|
|
|
|
|
|
| |
Now that we use the proper REQ_OP_WRITE_ZEROES operation everywhere we can
kill this hack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| | |
We've added a considerable amount of fixes for stalls and issues
with the blk-mq scheduling in the 4.11 series since forking
off the for-4.12/block branch. We need to do improvements on
top of that for 4.12, so pull in the previous fixes to make
our lives easier going forward.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
In elevator_switch(), if blk_mq_init_sched() fails, we attempt to fall
back to the original scheduler. However, at this point, we've already
torn down the original scheduler's tags, so this causes a crash. Doing
the fallback like the legacy elevator path is much harder for mq, so fix
it by just falling back to none, instead.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
CONFIG_DEBUG_TEST_DRIVER_REMOVE found a possible leak of q->rq_wb when a
request queue is reregistered. This has been a problem since wbt was
introduced, but the WARN_ON(!list_empty(&stats->callbacks)) in the
blk-stat rework exposed it. Fix it by cleaning up wbt when we unregister
the queue.
Fixes: 87760e5eef35 ("block: hook up writeback throttling")
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Now that the remaining drivers have been converted to one request queue
per gendisk, let's warn if a request queue gets registered more than
once. This will catch future drivers which might do it inadvertently or
any old drivers that I may have missed.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The throtl_slice is 100ms by default. This is a long time for SSD, a lot
of IO can run. To make cgroups have smoother throughput, we choose a
small value (20ms) for SSD.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
throtl_slice is important for blk-throttling. It's called slice
internally but it really is a time window blk-throttling samples data.
blk-throttling will make decision based on the samplings. An example is
bandwidth measurement. A cgroup's bandwidth is measured in the time
interval of throtl_slice.
A small throtl_slice meanse cgroups have smoother throughput but burn
more CPUs. It has 100ms default value, which is not appropriate for all
disks. A fast SSD can dispatch a lot of IOs in 100ms. This patch makes
it tunable.
Since throtl_slice isn't a time slice, the sysfs name
'throttle_sample_time' reflects its character better.
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently, statistics are gathered in ~0.13s windows, and users grab the
statistics whenever they need them. This is not ideal for both in-tree
users:
1. Writeback throttling wants its own dynamically sized window of
statistics. Since the blk-stats statistics are reset after every
window and the wbt windows don't line up with the blk-stats windows,
wbt doesn't see every I/O.
2. Polling currently grabs the statistics on every I/O. Again, depending
on how the window lines up, we may miss some I/Os. It's also
unnecessary overhead to get the statistics on every I/O; the hybrid
polling heuristic would be just as happy with the statistics from the
previous full window.
This reworks the blk-stats infrastructure to be callback-based: users
register a callback that they want called at a given time with all of
the statistics from the window during which the callback was active.
Users can dynamically bucketize the statistics. wbt and polling both
currently use read vs. write, but polling can be extended to further
subdivide based on request size.
The callbacks are kept on an RCU list, and each callback has percpu
stats buffers. There will only be a few users, so the overhead on the
I/O completion side is low. The stats flushing is also simplified
considerably: since the timer function is responsible for clearing the
statistics, we don't have to worry about stale statistics.
wbt is a trivial conversion. After the conversion, the windowing problem
mentioned above is fixed.
For polling, we register an extra callback that caches the previous
window's statistics in the struct request_queue for the hybrid polling
heuristic to use.
Since we no longer have a single stats buffer for the request queue,
this also removes the sysfs and debugfs stats entries. To replace those,
we add a debugfs entry for the poll statistics.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|/
|
|
|
|
|
|
|
| |
The stats buckets will become generic soon, so make the existing users
use the common READ and WRITE definitions instead of one internal to
blk-stat.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
For legacy scheduling, we always call ioc_exit_icq() with both the
ioc and queue lock held. This poses a problem for blk-mq with
scheduling, since the queue lock isn't what we use in the scheduler.
And since we don't need the queue lock held for ioc exit there,
don't grab it and leave any extra locking up to the blk-mq scheduler.
Reported-by: Paolo Valente <paolo.valente@linaro.org>
Tested-by: Paolo Valente <paolo.valente@linaro.org>
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
When a new disk shows up, sysfs queue directory is created before elevator
is registered. This allows a user to attempt a scheduler switch even though
the initial registration hasn't completed yet.
In one scenario, blk_register_queue() calls elv_register_queue() and
right before cfq_registered_queue() is called, another process executes
elevator_switch() and replaces q->elevator with deadline scheduler. When
cfq_registered_queue() executes it interprets e->elevator_data as struct
cfq_data even though it is actually struct deadline_data.
Grab q->sysfs_lock in blk_register_queue() to synchronize with sysfs
callers.
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add a new merge strategy that merges discard bios into a request until the
maximum number of discard ranges (or the maximum discard size) is reached
from the plug merging code. I/O scheduler merging is not wired up yet
but might also be useful, although not for fast devices like NVMe which
are the only user for now.
Note that for now we don't support limiting the size of each discard range,
but if needed that can be added later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
|
|
|
|
|
|
|
| |
I noticed that when booting with a default blk-mq I/O scheduler, the
/sys/block/*/queue/iosched directory was missing. However, switching
after boot did create the directory. This is because we skip the initial
elevator register/unregister when we don't have a ->request_fn(), but we
should still do it for the ->mq_ops case.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
|
|
|
| |
This needs to happen after we tear down blktrace.
Signed-off-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
|
|
|
|
|
|
|
| |
Instead of storing backing_dev_info inside struct request_queue,
allocate it dynamically, reference count it, and free it when the last
reference is dropped. Currently only request_queue holds the reference
but in the following patch we add other users referencing
backing_dev_info.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
|
|
|
|
|
|
|
| |
We will want to have struct backing_dev_info allocated separately from
struct request_queue. As the first step add pointer to backing_dev_info
to request_queue and convert all users touching it. No functional
changes in this patch.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
|
|
|
|
|
|
|
| |
This mirrors the blk-mq capabilities to allocate extra drivers-specific
data behind struct request by setting a cmd_size field, as well as having
a constructor / destructor for it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pull block layer updates from Jens Axboe:
"This is the main block pull request this series. Contrary to previous
release, I've kept the core and driver changes in the same branch. We
always ended up having dependencies between the two for obvious
reasons, so makes more sense to keep them together. That said, I'll
probably try and keep more topical branches going forward, especially
for cycles that end up being as busy as this one.
The major parts of this pull request is:
- Improved support for O_DIRECT on block devices, with a small
private implementation instead of using the pig that is
fs/direct-io.c. From Christoph.
- Request completion tracking in a scalable fashion. This is utilized
by two components in this pull, the new hybrid polling and the
writeback queue throttling code.
- Improved support for polling with O_DIRECT, adding a hybrid mode
that combines pure polling with an initial sleep. From me.
- Support for automatic throttling of writeback queues on the block
side. This uses feedback from the device completion latencies to
scale the queue on the block side up or down. From me.
- Support from SMR drives in the block layer and for SD. From Hannes
and Shaun.
- Multi-connection support for nbd. From Josef.
- Cleanup of request and bio flags, so we have a clear split between
which are bio (or rq) private, and which ones are shared. From
Christoph.
- A set of patches from Bart, that improve how we handle queue
stopping and starting in blk-mq.
- Support for WRITE_ZEROES from Chaitanya.
- Lightnvm updates from Javier/Matias.
- Supoort for FC for the nvme-over-fabrics code. From James Smart.
- A bunch of fixes from a whole slew of people, too many to name
here"
* 'for-4.10/block' of git://git.kernel.dk/linux-block: (182 commits)
blk-stat: fix a few cases of missing batch flushing
blk-flush: run the queue when inserting blk-mq flush
elevator: make the rqhash helpers exported
blk-mq: abstract out blk_mq_dispatch_rq_list() helper
blk-mq: add blk_mq_start_stopped_hw_queue()
block: improve handling of the magic discard payload
blk-wbt: don't throttle discard or write zeroes
nbd: use dev_err_ratelimited in io path
nbd: reset the setup task for NBD_CLEAR_SOCK
nvme-fabrics: Add FC LLDD loopback driver to test FC-NVME
nvme-fabrics: Add target support for FC transport
nvme-fabrics: Add host support for FC transport
nvme-fabrics: Add FC transport LLDD api definitions
nvme-fabrics: Add FC transport FC-NVME definitions
nvme-fabrics: Add FC transport error codes to nvme.h
Add type 0x28 NVME type code to scsi fc headers
nvme-fabrics: patch target code in prep for FC transport support
nvme-fabrics: set sqe.command_id in core not transports
parser: add u64 number parser
nvme-rdma: align to generic ib_event logging helper
...
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This adds a new block layer operation to zero out a range of
LBAs. This allows to implement zeroing for devices that don't use
either discard with a predictable zero pattern or WRITE SAME of zeroes.
The prominent example of that is NVMe with the Write Zeroes command,
but in the future, this should also help with improving the way
zeroing discards work. For this operation, suitable entry is exported in
sysfs which indicate the number of maximum bytes allowed in one
write zeroes operation by the device.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Currently there's no way to enable wbt if it's not enabled in the
kernel config by default for a device. Allow a write to the
'wbt_lat_usec' queue sysfs file to enable wbt.
This is useful for both the kernel config case, but also if the
device is CFQ managed and it was turned off by default.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Allow a write of '-1' to reset the default latency target for
a given device. This removes knowledge of the different default
settings for rotational vs non-rotational from user space.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The previous commit introduced the hybrid sleep/poll mode. Take
that one step further, and use the completion latencies to
automatically sleep for half the mean completion time. This is
a good approximation.
This changes the 'io_poll_delay' sysfs file a bit to expose the
various options. Depending on the value, the polling code will
behave differently:
-1 Never enter hybrid sleep mode
0 Use half of the completion mean for the sleep delay
>0 Use this specific value as the sleep delay
Signed-off-by: Jens Axboe <axboe@fb.com>
Tested-By: Stephen Bates <sbates@raithlin.com>
Reviewed-By: Stephen Bates <sbates@raithlin.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
This patch enables a hybrid polling mode. Instead of polling after IO
submission, we can induce an artificial delay, and then poll after that.
For example, if the IO is presumed to complete in 8 usecs from now, we
can sleep for 4 usecs, wake up, and then do our polling. This still puts
a sleep/wakeup cycle in the IO path, but instead of the wakeup happening
after the IO has completed, it'll happen before. With this hybrid
scheme, we can achieve big latency reductions while still using the same
(or less) amount of CPU.
Signed-off-by: Jens Axboe <axboe@fb.com>
Tested-By: Stephen Bates <sbates@raithlin.com>
Reviewed-By: Stephen Bates <sbates@raithlin.com>
|
| |
| |
| |
| |
| |
| |
| | |
Again a leftover from when the throttling code was generic. Now that we
just have the block user, get rid of the stat ops and indirections.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Enable throttling of buffered writeback to make it a lot
more smooth, and has way less impact on other system activity.
Background writeback should be, by definition, background
activity. The fact that we flush huge bundles of it at the time
means that it potentially has heavy impacts on foreground workloads,
which isn't ideal. We can't easily limit the sizes of writes that
we do, since that would impact file system layout in the presence
of delayed allocation. So just throttle back buffered writeback,
unless someone is waiting for it.
The algorithm for when to throttle takes its inspiration in the
CoDel networking scheduling algorithm. Like CoDel, blk-wb monitors
the minimum latencies of requests over a window of time. In that
window of time, if the minimum latency of any request exceeds a
given target, then a scale count is incremented and the queue depth
is shrunk. The next monitoring window is shrunk accordingly. Unlike
CoDel, if we hit a window that exhibits good behavior, then we
simply increment the scale count and re-calculate the limits for that
scale value. This prevents us from oscillating between a
close-to-ideal value and max all the time, instead remaining in the
windows where we get good behavior.
Unlike CoDel, blk-wb allows the scale count to to negative. This
happens if we primarily have writes going on. Unlike positive
scale counts, this doesn't change the size of the monitoring window.
When the heavy writers finish, blk-bw quickly snaps back to it's
stable state of a zero scale count.
The patch registers a sysfs entry, 'wb_lat_usec'. This sets the latency
target to me met. It defaults to 2 msec for non-rotational storage, and
75 msec for rotational storage. Setting this value to '0' disables
blk-wb. Generally, a user would not have to touch this setting.
We don't enable WBT on devices that are managed with CFQ, and have
a non-root block cgroup attached. If we have a proportional share setup
on this particular disk, then the wbt throttling will interfere with
that. We don't have a strong need for wbt for that case, since we will
rely on CFQ doing that for us.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
For legacy block, we simply track them in the request queue. For
blk-mq, we track them on a per-sw queue basis, which we can then
sum up through the hardware queues and finally to a per device
state.
The stats are tracked in, roughly, 0.1s interval windows.
Add sysfs files to display the stats.
The feature is off by default, to avoid any extra overhead. In-kernel
users of it can turn it on by setting QUEUE_FLAG_STATS in the queue
flags. We currently don't turn it on if someone just reads any of
the stats files, that is something we could add as well.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
The queue limits already have a 'chunk_sectors' setting, so
we should be presenting it via sysfs.
Signed-off-by: Hannes Reinecke <hare@suse.de>
[Damien: Updated Documentation/ABI/testing/sysfs-block]
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add the zoned queue limit to indicate the zoning model of a block device.
Defined values are 0 (BLK_ZONED_NONE) for regular block devices,
1 (BLK_ZONED_HA) for host-aware zone block devices and 2 (BLK_ZONED_HM)
for host-managed zone block devices. The standards defined drive managed
model is not defined here since these block devices do not provide any
command for accessing zone information. Drive managed model devices will
be reported as BLK_ZONED_NONE.
The helper functions blk_queue_zoned_model and bdev_zoned_model return
the zoned limit and the functions blk_queue_is_zoned and bdev_is_zoned
return a boolean for callers to test if a block device is zoned.
The zoned attribute is also exported as a string to applications via
sysfs. BLK_ZONED_NONE shows as "none", BLK_ZONED_HA as "host-aware" and
BLK_ZONED_HM as "host-managed".
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Tested-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
We ran into a funky issue, where someone doing 256K buffered reads saw
128K requests at the device level. Turns out it is read-ahead capping
the request size, since we use 128K as the default setting. This
doesn't make a lot of sense - if someone is issuing 256K reads, they
should see 256K reads, regardless of the read-ahead setting, if the
underlying device can support a 256K read in a single command.
This patch introduces a bdi hint, io_pages. This is the soft max IO
size for the lower level, I've hooked it up to the bdev settings here.
Read-ahead is modified to issue the maximum of the user request size,
and the read-ahead max size, but capped to the max request size on the
device side. The latter is done to avoid reading ahead too much, if the
application asks for a huge read. With this patch, the kernel behaves
like the application expects.
Link: http://lkml.kernel.org/r/1479498073-8657-1-git-send-email-axboe@fb.com
Signed-off-by: Jens Axboe <axboe@fb.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
|
|
|
|
| |
Enable devices without a gendisk instance to register itself with blk-mq
and expose the associated multi-queue sysfs entries.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
|
|
|
|
|
|
| |
Provides the ability to identify DAX enabled devices in userspace.
Signed-off-by: Yigal Korman <yigal@plexistor.com>
Signed-off-by: Toshi Kani <toshi.kani@hpe.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Add an internal helper and flag for setting whether a queue has
write back caching, or write through (or none). Add a sysfs file
to show this as well, and make it changeable from user space.
This will replace the (awkward) blk_queue_flush() interface that
drivers currently use to inform the block layer of write cache state
and capabilities.
Signed-off-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
|
|
|
|
| |
We get this right for queue_discard_max_show but not max_hw_show. Follow the
same pattern as queue_discard_max_show instead so that we don't truncate.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|\ |
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Commit 4f258a46346c ("sd: Fix maximum I/O size for BLOCK_PC requests")
had the unfortunate side-effect of removing an implicit clamp to
BLK_DEF_MAX_SECTORS for REQ_TYPE_FS requests in the block layer
code. This caused problems for some SMR drives.
Debugging this issue revealed a few problems with the existing
infrastructure since the block layer didn't know how to deal with
device-imposed limits, only limits set by the I/O controller.
- Introduce a new queue limit, max_dev_sectors, which is used by the
ULD to signal the maximum sectors for a REQ_TYPE_FS request.
- Ensure that max_dev_sectors is correctly stacked and taken into
account when overriding max_sectors through sysfs.
- Rework sd_read_block_limits() so it saves the max_xfer and opt_xfer
values for later processing.
- In sd_revalidate() set the queue's max_dev_sectors based on the
MAXIMUM TRANSFER LENGTH value in the Block Limits VPD. If this value
is not reported, fall back to a cap based on the CDB TRANSFER LENGTH
field size.
- In sd_revalidate(), use OPTIMAL TRANSFER LENGTH from the Block Limits
VPD--if reported and sane--to signal the preferred device transfer
size for FS requests. Otherwise use BLK_DEF_MAX_SECTORS.
- blk_limits_max_hw_sectors() is no longer used and can be removed.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=93581
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: sweeneygj@gmx.com
Tested-by: Arzeets <anatol.pomozov@gmail.com>
Tested-by: David Eisner <david.eisner@oriel.oxon.org>
Tested-by: Mario Kicherer <dev@kicherer.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Add basic support for polling for specific IO to complete. This uses
the cookie that blk-mq passes back, which enables the block layer
to pass this cookie to the driver to spin for a specific request.
This will be combined with request latency tracking, so we can make
qualified decisions about when to poll and when not to. For now, for
benchmark purposes, we add a sysfs file that controls whether polling
is enabled or not.
Signed-off-by: Jens Axboe <axboe@fb.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Keith Busch <keith.busch@intel.com>
|
|\ \
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | |
| | | |
Pull block integrity updates from Jens Axboe:
""This is the joint work of Dan and Martin, cleaning up and improving
the support for block data integrity"
* 'for-4.4/integrity' of git://git.kernel.dk/linux-block:
block, libnvdimm, nvme: provide a built-in blk_integrity nop profile
block: blk_flush_integrity() for bio-based drivers
block: move blk_integrity to request_queue
block: generic request_queue reference counting
nvme: suspend i/o during runtime blk_integrity_unregister
md: suspend i/o during runtime blk_integrity_unregister
md, dm, scsi, nvme, libnvdimm: drop blk_integrity_unregister() at shutdown
block: Inline blk_integrity in struct gendisk
block: Export integrity data interval size in sysfs
block: Reduce the size of struct blk_integrity
block: Consolidate static integrity profile properties
block: Move integrity kobject to struct gendisk
|
| |/
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Allow pmem, and other synchronous/bio-based block drivers, to fallback
on a per-cpu reference count managed by the core for tracking queue
live/dead state.
The existing per-cpu reference count for the blk_mq case is promoted to
be used in all block i/o scenarios. This involves initializing it by
default, waiting for it to drop to zero at exit, and holding a live
reference over the invocation of q->make_request_fn() in
generic_make_request(). The blk_mq code continues to take its own
reference per blk_mq request and retains the ability to freeze the
queue, but the check that the queue is frozen is moved to
generic_make_request().
This fixes crash signatures like the following:
BUG: unable to handle kernel paging request at ffff880140000000
[..]
Call Trace:
[<ffffffff8145e8bf>] ? copy_user_handle_tail+0x5f/0x70
[<ffffffffa004e1e0>] pmem_do_bvec.isra.11+0x70/0xf0 [nd_pmem]
[<ffffffffa004e331>] pmem_make_request+0xd1/0x200 [nd_pmem]
[<ffffffff811c3162>] ? mempool_alloc+0x72/0x1a0
[<ffffffff8141f8b6>] generic_make_request+0xd6/0x110
[<ffffffff8141f966>] submit_bio+0x76/0x170
[<ffffffff81286dff>] submit_bh_wbc+0x12f/0x160
[<ffffffff81286e62>] submit_bh+0x12/0x20
[<ffffffff813395bd>] jbd2_write_superblock+0x8d/0x170
[<ffffffff8133974d>] jbd2_mark_journal_empty+0x5d/0x90
[<ffffffff813399cb>] jbd2_journal_destroy+0x24b/0x270
[<ffffffff810bc4ca>] ? put_pwq_unlocked+0x2a/0x30
[<ffffffff810bc6f5>] ? destroy_workqueue+0x225/0x250
[<ffffffff81303494>] ext4_put_super+0x64/0x360
[<ffffffff8124ab1a>] generic_shutdown_super+0x6a/0xf0
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|/
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
bdi's are initialized in two steps, bdi_init() and bdi_register(), but
destroyed in a single step by bdi_destroy() which, for a bdi embedded
in a request_queue, is called during blk_cleanup_queue() which makes
the queue invisible and starts the draining of remaining usages.
A request_queue's user can access the congestion state of the embedded
bdi as long as it holds a reference to the queue. As such, it may
access the congested state of a queue which finished
blk_cleanup_queue() but hasn't reached blk_release_queue() yet.
Because the congested state was embedded in backing_dev_info which in
turn is embedded in request_queue, accessing the congested state after
bdi_destroy() was called was fine. The bdi was destroyed but the
memory region for the congested state remained accessible till the
queue got released.
a13f35e87140 ("writeback: don't embed root bdi_writeback_congested in
bdi_writeback") changed the situation. Now, the root congested state
which is expected to be pinned while request_queue remains accessible
is separately reference counted and the base ref is put during
bdi_destroy(). This means that the root congested state may go away
prematurely while the queue is between bdi_dstroy() and
blk_cleanup_queue(), which was detected by Andrey's KASAN tests.
The root cause of this problem is that bdi doesn't distinguish the two
steps of destruction, unregistration and release, and now the root
congested state actually requires a separate release step. To fix the
issue, this patch separates out bdi_unregister() and bdi_exit() from
bdi_destroy(). bdi_unregister() is called from blk_cleanup_queue()
and bdi_exit() from blk_release_queue(). bdi_destroy() is now just a
simple wrapper calling the two steps back-to-back.
While at it, the prototype of bdi_destroy() is moved right below
bdi_setup_and_register() so that the counterpart operations are
located together.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: a13f35e87140 ("writeback: don't embed root bdi_writeback_congested in bdi_writeback")
Cc: stable@vger.kernel.org # v4.2+
Reported-and-tested-by: Andrey Konovalov <andreyknvl@google.com>
Link: http://lkml.kernel.org/g/CAAeHK+zUJ74Zn17=rOyxacHU18SgCfC6bsYW=6kCY5GXJBwGfQ@mail.gmail.com
Reviewed-by: Jan Kara <jack@suse.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The way the block layer is currently written, it goes to great lengths
to avoid having to split bios; upper layer code (such as bio_add_page())
checks what the underlying device can handle and tries to always create
bios that don't need to be split.
But this approach becomes unwieldy and eventually breaks down with
stacked devices and devices with dynamic limits, and it adds a lot of
complexity. If the block layer could split bios as needed, we could
eliminate a lot of complexity elsewhere - particularly in stacked
drivers. Code that creates bios can then create whatever size bios are
convenient, and more importantly stacked drivers don't have to deal with
both their own bio size limitations and the limitations of the
(potentially multiple) devices underneath them. In the future this will
let us delete merge_bvec_fn and a bunch of other code.
We do this by adding calls to blk_queue_split() to the various
make_request functions that need it - a few can already handle arbitrary
size bios. Note that we add the call _after_ any call to
blk_queue_bounce(); this means that blk_queue_split() and
blk_recalc_rq_segments() don't need to be concerned with bouncing
affecting segment merging.
Some make_request_fn() callbacks were simple enough to audit and verify
they don't need blk_queue_split() calls. The skipped ones are:
* nfhd_make_request (arch/m68k/emu/nfblock.c)
* axon_ram_make_request (arch/powerpc/sysdev/axonram.c)
* simdisk_make_request (arch/xtensa/platforms/iss/simdisk.c)
* brd_make_request (ramdisk - drivers/block/brd.c)
* mtip_submit_request (drivers/block/mtip32xx/mtip32xx.c)
* loop_make_request
* null_queue_bio
* bcache's make_request fns
Some others are almost certainly safe to remove now, but will be left
for future patches.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: drbd-user@lists.linbit.com
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Jim Paris <jim@jtan.com>
Cc: Philip Kelleher <pjk1939@linux.vnet.ibm.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Andreas Dilger <andreas.dilger@intel.com>
Acked-by: NeilBrown <neilb@suse.de> (for the 'md/md.c' bits)
Acked-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
[dpark: skip more mq-based drivers, resolve merge conflicts, etc.]
Signed-off-by: Dongsu Park <dpark@posteo.net>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Lots of devices support huge discard sizes these days. Depending
on how the device handles them internally, huge discards can
introduce massive latencies (hundreds of msec) on the device side.
We have a sysfs file, discard_max_bytes, that advertises the max
hardware supported discard size. Make this writeable, and split
the settings into a soft and hard limit. This can be set from
'discard_granularity' and up to the hardware limit.
Add a new sysfs file, 'discard_max_hw_bytes', that shows the hw
set limit.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|\
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| |
| | |
Pull cgroup writeback support from Jens Axboe:
"This is the big pull request for adding cgroup writeback support.
This code has been in development for a long time, and it has been
simmering in for-next for a good chunk of this cycle too. This is one
of those problems that has been talked about for at least half a
decade, finally there's a solution and code to go with it.
Also see last weeks writeup on LWN:
http://lwn.net/Articles/648292/"
* 'for-4.2/writeback' of git://git.kernel.dk/linux-block: (85 commits)
writeback, blkio: add documentation for cgroup writeback support
vfs, writeback: replace FS_CGROUP_WRITEBACK with SB_I_CGROUPWB
writeback: do foreign inode detection iff cgroup writeback is enabled
v9fs: fix error handling in v9fs_session_init()
bdi: fix wrong error return value in cgwb_create()
buffer: remove unusued 'ret' variable
writeback: disassociate inodes from dying bdi_writebacks
writeback: implement foreign cgroup inode bdi_writeback switching
writeback: add lockdep annotation to inode_to_wb()
writeback: use unlocked_inode_to_wb transaction in inode_congested()
writeback: implement unlocked_inode_to_wb transaction and use it for stat updates
writeback: implement [locked_]inode_to_wb_and_lock_list()
writeback: implement foreign cgroup inode detection
writeback: make writeback_control track the inode being written back
writeback: relocate wb[_try]_get(), wb_put(), inode_{attach|detach}_wb()
mm: vmscan: disable memcg direct reclaim stalling if cgroup writeback support is in use
writeback: implement memcg writeback domain based throttling
writeback: reset wb_domain->dirty_limit[_tstmp] when memcg domain size changes
writeback: implement memcg wb_domain
writeback: update wb_over_bg_thresh() to use wb_domain aware operations
...
|