summaryrefslogtreecommitdiffstats
path: root/arch/powerpc/kernel
Commit message (Collapse)AuthorAgeFilesLines
...
| * | | | | powerpc/sparse: Fix plain integer as NULL pointer warningMathieu Malaterre2018-05-252-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Trivial fix to remove the following sparse warnings: arch/powerpc/kernel/module_32.c:112:74: warning: Using plain integer as NULL pointer arch/powerpc/kernel/module_32.c:117:74: warning: Using plain integer as NULL pointer drivers/macintosh/via-pmu.c:1155:28: warning: Using plain integer as NULL pointer drivers/macintosh/via-pmu.c:1230:20: warning: Using plain integer as NULL pointer drivers/macintosh/via-pmu.c:1385:36: warning: Using plain integer as NULL pointer drivers/macintosh/via-pmu.c:1752:23: warning: Using plain integer as NULL pointer drivers/macintosh/via-pmu.c:2084:19: warning: Using plain integer as NULL pointer drivers/macintosh/via-pmu.c:2110:32: warning: Using plain integer as NULL pointer drivers/macintosh/via-pmu.c:2167:19: warning: Using plain integer as NULL pointer drivers/macintosh/via-pmu.c:2183:19: warning: Using plain integer as NULL pointer drivers/macintosh/via-pmu.c:277:20: warning: Using plain integer as NULL pointer arch/powerpc/platforms/powermac/setup.c:155:67: warning: Using plain integer as NULL pointer arch/powerpc/platforms/powermac/setup.c:247:27: warning: Using plain integer as NULL pointer arch/powerpc/platforms/powermac/setup.c:249:27: warning: Using plain integer as NULL pointer arch/powerpc/platforms/powermac/setup.c:252:37: warning: Using plain integer as NULL pointer arch/powerpc/mm/tlb_hash32.c:127:21: warning: Using plain integer as NULL pointer arch/powerpc/mm/tlb_hash32.c:148:21: warning: Using plain integer as NULL pointer arch/powerpc/mm/tlb_hash32.c:44:21: warning: Using plain integer as NULL pointer arch/powerpc/mm/tlb_hash32.c:57:21: warning: Using plain integer as NULL pointer arch/powerpc/mm/tlb_hash32.c:87:21: warning: Using plain integer as NULL pointer arch/powerpc/kernel/btext.c:160:31: warning: Using plain integer as NULL pointer arch/powerpc/kernel/btext.c:167:22: warning: Using plain integer as NULL pointer arch/powerpc/kernel/btext.c:274:21: warning: Using plain integer as NULL pointer arch/powerpc/kernel/btext.c:285:31: warning: Using plain integer as NULL pointer arch/powerpc/include/asm/hugetlb.h:204:16: warning: Using plain integer as NULL pointer arch/powerpc/mm/ppc_mmu_32.c:170:21: warning: Using plain integer as NULL pointer arch/powerpc/platforms/powermac/pci.c:1227:23: warning: Using plain integer as NULL pointer arch/powerpc/platforms/powermac/pci.c:65:24: warning: Using plain integer as NULL pointer Also use `--fix` command line option from `script/checkpatch --strict` to remove the following: CHECK: Comparison to NULL could be written "!dispDeviceBase" #72: FILE: arch/powerpc/kernel/btext.c:160: + if (dispDeviceBase == NULL) CHECK: Comparison to NULL could be written "!vbase" #80: FILE: arch/powerpc/kernel/btext.c:167: + if (vbase == NULL) CHECK: Comparison to NULL could be written "!base" #89: FILE: arch/powerpc/kernel/btext.c:274: + if (base == NULL) CHECK: Comparison to NULL could be written "!dispDeviceBase" #98: FILE: arch/powerpc/kernel/btext.c:285: + if (dispDeviceBase == NULL) CHECK: Comparison to NULL could be written "strstr" #117: FILE: arch/powerpc/kernel/module_32.c:117: + if (strstr(secstrings + sechdrs[i].sh_name, ".debug") != NULL) CHECK: Comparison to NULL could be written "!Hash" #130: FILE: arch/powerpc/mm/ppc_mmu_32.c:170: + if (Hash == NULL) CHECK: Comparison to NULL could be written "Hash" #143: FILE: arch/powerpc/mm/tlb_hash32.c:44: + if (Hash != NULL) { CHECK: Comparison to NULL could be written "!Hash" #152: FILE: arch/powerpc/mm/tlb_hash32.c:57: + if (Hash == NULL) { CHECK: Comparison to NULL could be written "!Hash" #161: FILE: arch/powerpc/mm/tlb_hash32.c:87: + if (Hash == NULL) { CHECK: Comparison to NULL could be written "!Hash" #170: FILE: arch/powerpc/mm/tlb_hash32.c:127: + if (Hash == NULL) { CHECK: Comparison to NULL could be written "!Hash" #179: FILE: arch/powerpc/mm/tlb_hash32.c:148: + if (Hash == NULL) { ERROR: space required after that ';' (ctx:VxV) #192: FILE: arch/powerpc/platforms/powermac/pci.c:65: + for (; node != NULL;node = node->sibling) { CHECK: Comparison to NULL could be written "node" #192: FILE: arch/powerpc/platforms/powermac/pci.c:65: + for (; node != NULL;node = node->sibling) { CHECK: Comparison to NULL could be written "!region" #201: FILE: arch/powerpc/platforms/powermac/pci.c:1227: + if (region == NULL) CHECK: Comparison to NULL could be written "of_get_property" #214: FILE: arch/powerpc/platforms/powermac/setup.c:155: + if (of_get_property(np, "cache-unified", NULL) != NULL && dc) { CHECK: Comparison to NULL could be written "!np" #223: FILE: arch/powerpc/platforms/powermac/setup.c:247: + if (np == NULL) CHECK: Comparison to NULL could be written "np" #226: FILE: arch/powerpc/platforms/powermac/setup.c:249: + if (np != NULL) { CHECK: Comparison to NULL could be written "l2cr" #230: FILE: arch/powerpc/platforms/powermac/setup.c:252: + if (l2cr != NULL) { CHECK: Comparison to NULL could be written "via" #243: FILE: drivers/macintosh/via-pmu.c:277: + if (via != NULL) CHECK: Comparison to NULL could be written "current_req" #252: FILE: drivers/macintosh/via-pmu.c:1155: + if (current_req != NULL) { CHECK: Comparison to NULL could be written "!req" #261: FILE: drivers/macintosh/via-pmu.c:1230: + if (req == NULL || pmu_state != idle CHECK: Comparison to NULL could be written "!req" #270: FILE: drivers/macintosh/via-pmu.c:1385: + if (req == NULL) { CHECK: Comparison to NULL could be written "!pp" #288: FILE: drivers/macintosh/via-pmu.c:2084: + if (pp == NULL) CHECK: Comparison to NULL could be written "!pp" #297: FILE: drivers/macintosh/via-pmu.c:2110: + if (count < 1 || pp == NULL) CHECK: Comparison to NULL could be written "!pp" #306: FILE: drivers/macintosh/via-pmu.c:2167: + if (pp == NULL) CHECK: Comparison to NULL could be written "pp" #315: FILE: drivers/macintosh/via-pmu.c:2183: + if (pp != NULL) { Link: https://github.com/linuxppc/linux/issues/37 Signed-off-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc: Add __printf verification to prom_printfMathieu Malaterre2018-05-251-56/+58
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | __printf is useful to verify format and arguments. Fix arg mismatch reported by gcc, remove the following warnings (with W=1): arch/powerpc/kernel/prom_init.c:1467:31: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’ arch/powerpc/kernel/prom_init.c:1471:31: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’ arch/powerpc/kernel/prom_init.c:1504:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’ arch/powerpc/kernel/prom_init.c:1505:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’ arch/powerpc/kernel/prom_init.c:1506:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’ arch/powerpc/kernel/prom_init.c:1507:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’ arch/powerpc/kernel/prom_init.c:1508:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’ arch/powerpc/kernel/prom_init.c:1509:33: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’ arch/powerpc/kernel/prom_init.c:1975:39: error: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘unsigned int’ arch/powerpc/kernel/prom_init.c:1986:27: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’ arch/powerpc/kernel/prom_init.c:2567:38: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’ arch/powerpc/kernel/prom_init.c:2567:46: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘long unsigned int’ arch/powerpc/kernel/prom_init.c:2569:38: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘long unsigned int’ arch/powerpc/kernel/prom_init.c:2569:46: error: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3 has type ‘long unsigned int’ The patch also include arg mismatch fix for case with #define DEBUG_PROM (warning not listed here). This patch fix also the following warnings revealed by checkpatch: WARNING: Prefer using '"%s...", __func__' to using 'alloc_up', this function's name, in a string #101: FILE: arch/powerpc/kernel/prom_init.c:1235: + prom_debug("alloc_up(%lx, %lx)\n", size, align); and WARNING: Prefer using '"%s...", __func__' to using 'alloc_down', this function's name, in a string #138: FILE: arch/powerpc/kernel/prom_init.c:1278: + prom_debug("alloc_down(%lx, %lx, %s)\n", size, align, Signed-off-by: Mathieu Malaterre <malat@debian.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc/8xx: fix invalid register expression in head_8xx.SChristophe Leroy2018-05-251-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | New binutils generate the following warning AS arch/powerpc/kernel/head_8xx.o arch/powerpc/kernel/head_8xx.S: Assembler messages: arch/powerpc/kernel/head_8xx.S:916: Warning: invalid register expression This patch fixes it. Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc/ptrace: Fix setting 512B aligned breakpoints with PTRACE_SET_DEBUGREGMichael Neuling2018-05-211-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In commit e2a800beaca1 ("powerpc/hw_brk: Fix off by one error when validating DAWR region end") we fixed setting the DAWR end point to its max value via PPC_PTRACE_SETHWDEBUG. Unfortunately we broke PTRACE_SET_DEBUGREG when setting a 512 byte aligned breakpoint. PTRACE_SET_DEBUGREG currently sets the length of the breakpoint to zero (memset() in hw_breakpoint_init()). This worked with arch_validate_hwbkpt_settings() before the above patch was applied but is now broken if the breakpoint is 512byte aligned. This sets the length of the breakpoint to 8 bytes when using PTRACE_SET_DEBUGREG. Fixes: e2a800beaca1 ("powerpc/hw_brk: Fix off by one error when validating DAWR region end") Cc: stable@vger.kernel.org # v3.11+ Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc/ptrace: Fix enforcement of DAWR constraintsMichael Neuling2018-05-211-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Back when we first introduced the DAWR, in commit 4ae7ebe9522a ("powerpc: Change hardware breakpoint to allow longer ranges"), we screwed up the constraint making it a 1024 byte boundary rather than a 512. This makes the check overly permissive. Fortunately GDB is the only real user and it always did they right thing, so we never noticed. This fixes the constraint to 512 bytes. Fixes: 4ae7ebe9522a ("powerpc: Change hardware breakpoint to allow longer ranges") Cc: stable@vger.kernel.org # v3.9+ Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc/rtas: Fix spelling mistake "Discharching" -> "Discharging"Colin Ian King2018-05-181-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Trivial fix to spelling mistake in battery_charging array. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc/32: Use stmw/lmw for registers save/restore in asmChristophe Leroy2018-05-182-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | arch/powerpc/Makefile activates -mmultiple on BE PPC32 configs in order to use multiple word instructions in functions entry/exit. The patch does the same for the asm parts, for consistency. On processors like the 8xx on which insn fetching is pretty slow, this speeds up registers save/restore. Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> [mpe: PPC32 is BE only, so drop the endian checks] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc: Avoid an unnecessary test and branch in longjmp()Christophe Leroy2018-05-181-5/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Doing the test at exit of the function avoids an unnecessary test and branch inside longjmp(). Semantics are unchanged. Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr> Reviewed-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc/prom: Drop support for old FDT versionsMichael Ellerman2018-05-111-19/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In commit e6a6928c3ea1 ("of/fdt: Convert FDT functions to use libfdt") (Apr 2014), the generic flat device tree code dropped support for flat device tree's older than version 0x10 (16). We still have code in our CPU scanning to cope with flat device tree versions earlier than 2, which can now never trigger, so drop it. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc: Make it clearer that systbl check errors are errorsMichael Ellerman2018-05-101-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the systbl_chk.sh checks fail we print a message, but with no indication that it's an error. That makes it hard to find in build logs with eg. grep. So prefix any output with "Error:". Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc/syscalls: kill ppc32_select()Al Viro2018-05-101-9/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | it had always been pointless - compat_sys_select() sign-extends the first argument just fine on its own. Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> [mpe: Use COMPAT_SPU_NEW() to keep systbl_chk.sh happy] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc/syscalls: Add COMPAT_SPU_NEW() macroMichael Ellerman2018-05-102-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently the select system call is wired up with the SYSX_SPU() macro. The SYSX_SPU() is not handled by systbl_chk.c, which means the syscall number for select is not checked. That hides the fact that the syscall number for select is actually __NR__newselect not __NR_select. In a following patch we'd like to drop ppc32_select() which means select will become a regular COMPAT_SYS_SPU() syscall. But COMPAT_SYS_SPU() can't deal with the fact that the syscall number is actually __NR__newselect. We also can't just redefine __NR_select because that's still used for the old select call. So add a new COMPAT_NEW_SPU() that does the same thing as COMPAT_SYS_SPU() except it encodes that we're using the new number. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc/syscalls: switch rtas(2) to SYSCALL_DEFINEAl Viro2018-05-103-3/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> [mpe: Update sys_ni.c for s/ppc_rtas/sys_rtas/] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc/syscalls: signal_{32, 64} - switch to SYSCALL_DEFINEAl Viro2018-05-103-30/+31
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> [mpe: Fix sys_debug_setcontext() prototype to return long] Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc/syscalls: Switch trivial cases to SYSCALL_DEFINEAl Viro2018-05-102-5/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc/livepatch: Implement reliable stack tracing for the consistency modelTorsten Duwe2018-05-101-1/+118
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The "Power Architecture 64-Bit ELF V2 ABI" says in section 2.3.2.3: [...] There are several rules that must be adhered to in order to ensure reliable and consistent call chain backtracing: * Before a function calls any other function, it shall establish its own stack frame, whose size shall be a multiple of 16 bytes. – In instances where a function’s prologue creates a stack frame, the back-chain word of the stack frame shall be updated atomically with the value of the stack pointer (r1) when a back chain is implemented. (This must be supported as default by all ELF V2 ABI-compliant environments.) [...] – The function shall save the link register that contains its return address in the LR save doubleword of its caller’s stack frame before calling another function. To me this sounds like the equivalent of HAVE_RELIABLE_STACKTRACE. This patch may be unneccessarily limited to ppc64le, but OTOH the only user of this flag so far is livepatching, which is only implemented on PPCs with 64-LE, a.k.a. ELF ABI v2. Feel free to add other ppc variants, but so far only ppc64le got tested. This change also implements save_stack_trace_tsk_reliable() for ppc64le that checks for the above conditions, where possible. Signed-off-by: Torsten Duwe <duwe@suse.de> Signed-off-by: Nicolai Stange <nstange@suse.de> Acked-by: Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc/watchdog: provide more data in watchdog messagesNicholas Piggin2018-05-101-3/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Provide timebase and timebase of last heartbeat in watchdog lockup messages. Also provide a stack trace of when a CPU becomes un-stuck, which can be useful -- it could be where irqs are re-enabled, so it may be the end of the critical section which is responsible for the latency which is useful information. Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc/watchdog: don't update the watchdog timestamp if a lockup is detectedNicholas Piggin2018-05-101-2/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The watchdog heartbeat timestamp is updated when the local heartbeat timer fires (or touch_nmi_watchdog() is called). This is an interesting data point, so don't overwrite it when the soft-NMI interrupt detects a hard lockup. That code came from a pre- merge version to prevent hard lockup messages flood, but that's taken care of with the stuck CPU logic now, so there is no reason to update the heartbeat timestamp here. Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc/64/kexec: fix race in kexec when XIVE is shutdownCédric Le Goater2018-05-101-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The kexec_state KEXEC_STATE_IRQS_OFF barrier is reached by all secondary CPUs before the kexec_cpu_down() operation is called on secondaries. This can raise conflicts and provoque errors in the XIVE hcalls when XIVE is shutdown with H_INT_RESET on the primary CPU. To synchronize the kexec_cpu_down() operations and make sure the secondaries have completed their task before the primary starts doing the same, let's move the primary kexec_cpu_down() after the KEXEC_STATE_REAL_MODE barrier. This change of the ending sequence of kexec is mostly useful on the pseries platform but it impacts also the powernv, ps3 and 85xx platforms. powernv can be easily tested and fixed but some caution is required for the other two. Signed-off-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc/watchdog: fix typo 'can by' to 'can be'Wolfram Sang2018-05-101-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc/fadump: Unregister fadump on kexec down path.Mahesh Salgaonkar2018-05-031-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Unregister fadump on kexec down path otherwise the fadump registration in new kexec-ed kernel complains that fadump is already registered. This makes new kernel to continue using fadump registered by previous kernel which may lead to invalid vmcore generation. Hence this patch fixes this issue by un-registering fadump in fadump_cleanup() which is called during kexec path so that new kernel can register fadump with new valid values. Fixes: b500afff11f6 ("fadump: Invalidate registration and release reserved memory for general use.") Cc: stable@vger.kernel.org # v3.4+ Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc/fadump: Do not use hugepages when fadump is activeHari Bathini2018-05-031-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FADump capture kernel boots in restricted memory environment preserving the context of previous kernel to save vmcore. Supporting hugepages in such environment makes things unnecessarily complicated, as hugepages need memory set aside for them. This means most of the capture kernel's memory is used in supporting hugepages. In most cases, this results in out-of-memory issues while booting FADump capture kernel. But hugepages are not of much use in capture kernel whose only job is to save vmcore. So, disabling hugepages support, when fadump is active, is a reliable solution for the out of memory issues. Introducing a flag variable to disable HugeTLB support when fadump is active. Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com> Reviewed-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc/fadump: exclude memory holes while reserving memory in second kernelMahesh Salgaonkar2018-05-031-6/+23
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The second kernel, during early boot after the crash, reserves rest of the memory above boot memory size to make sure it does not touch any of the dump memory area. It uses memblock_reserve() that reserves the specified memory region irrespective of memory holes present within that region. There are chances where previous kernel would have hot removed some of its memory leaving memory holes behind. In such cases fadump kernel reports incorrect number of reserved pages through arch_reserved_kernel_pages() hook causing kernel to hang or panic. Fix this by excluding memory holes while reserving rest of the memory above boot memory size during second kernel boot after crash. Signed-off-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com> Signed-off-by: Hari Bathini <hbathini@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc: Only support DYNAMIC_FTRACE not staticMichael Ellerman2018-05-035-56/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We've had dynamic ftrace support for over 9 years since Steve first wrote it, all the distros use dynamic, and static is basically untested these days, so drop support for static ftrace. Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc64/ftrace: Implement support for ftrace_regs_caller()Naveen N. Rao2018-05-033-24/+259
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With -mprofile-kernel, we always save the full register state in ftrace_caller(). While this works, this is inefficient if we're not interested in the register state, such as when we're using the function tracer. Rename the existing ftrace_caller() as ftrace_regs_caller() and provide a simpler implementation for ftrace_caller() that is used when registers are not required to be saved. Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc64/ftrace: Use the generic version of ftrace_replace_code()Naveen N. Rao2018-05-031-36/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Our implementation matches that of the generic version, which also handles FTRACE_UPDATE_MODIFY_CALL. So, remove our implementation in favor of the generic version. Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc64/module: Tighten detection of mcount call sites with -mprofile-kernelNaveen N. Rao2018-05-031-6/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | For R_PPC64_REL24 relocations, we suppress emitting instructions for TOC load/restore in the relocation stub if the relocation is for _mcount() call when using -mprofile-kernel ABI. To detect this, we check if the preceding instructions are per the standard set of instructions emitted by gcc: either the two instruction sequence of 'mflr r0; std r0,16(r1)', or the more optimized variant of a single 'mflr r0'. This is not sufficient since nothing prevents users from hand coding sequences involving a 'mflr r0' followed by a 'bl'. For removing the toc save instruction from the stub, we additionally check if the symbol is "_mcount". Add the same check here as well. Also rename is_early_mcount_callsite() to is_mprofile_mcount_callsite() since that is what is being checked. The use of "early" is misleading since there is nothing involving this function that qualifies as early. Fixes: 153086644fd1f ("powerpc/ftrace: Add support for -mprofile-kernel ftrace ABI") Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc64/kexec: Hard disable ftrace before switching to the new kernelNaveen N. Rao2018-05-031-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If function_graph tracer is enabled during kexec, we see the below exception in the simulator: root@(none):/# kexec -e kvm: exiting hardware virtualization kexec_core: Starting new kernel [ 19.262020070,5] OPAL: Switch to big-endian OS kexec: Starting switchover sequence. Interrupt to 0xC000000000004380 from 0xC000000000004380 ** Execution stopped: Continuous Interrupt, Instruction caused exception, ** Now that we have a more effective way to completely disable ftrace on ppc64, let's also use that before switching to a new kernel during kexec. Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc64/ftrace: Disable ftrace during hotplugNaveen N. Rao2018-05-031-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Disable ftrace when a cpu is about to go offline. When the cpu is woken up, ftrace will get enabled in start_secondary(). Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc64/ftrace: Delay enabling ftrace on secondary cpusNaveen N. Rao2018-05-032-3/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On the boot cpu, though we enable paca->ftrace_enabled in early_setup() (via cpu_ready_for_interrupts()), we don't start tracing until much later since ftrace is not initialized yet and since we only support DYNAMIC_FTRACE on powerpc. However, it is possible that ftrace has been initialized by the time some of the secondary cpus start up. In this case, we will try to trace some of the early boot code which can cause problems. To address this, move setting paca->ftrace_enabled from cpu_ready_for_interrupts() to early_setup() for the boot cpu, and towards the end of start_secondary() for secondary cpus. Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
| * | | | | powerpc64/ftrace: Add a field in paca to disable ftrace in unsafe code pathsNaveen N. Rao2018-05-034-0/+22
| |/ / / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We have some C code that we call into from real mode where we cannot take any exceptions. Though the C functions themselves are mostly safe, if these functions are traced, there is a possibility that we may take an exception. For instance, in certain conditions, the ftrace code uses WARN(), which uses a 'trap' to do its job. For such scenarios, introduce a new field in paca 'ftrace_enabled', which is checked on ftrace entry before continuing. This field can then be set to zero to disable/pause ftrace, and set to a non-zero value to resume ftrace. Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
* | | | | Merge tag 'kbuild-v4.18' of ↵Linus Torvalds2018-06-061-11/+11
|\ \ \ \ \ | |_|_|/ / |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull Kbuild updates from Masahiro Yamada: - improve fixdep to coalesce consecutive slashes in dep-files - fix some issues of the maintainer string generation in deb-pkg script - remove unused CONFIG_HAVE_UNDERSCORE_SYMBOL_PREFIX and clean-up several tools and linker scripts - clean-up modpost - allow to enable the dead code/data elimination for PowerPC in EXPERT mode - improve two coccinelle scripts for better performance - pass endianness and machine size flags to sparse for all architecture - misc fixes * tag 'kbuild-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (25 commits) kbuild: add machine size to CHECKFLAGS kbuild: add endianness flag to CHEKCFLAGS kbuild: $(CHECK) doesnt need NOSTDINC_FLAGS twice scripts: Fixed printf format mismatch scripts/tags.sh: use `find` for $ALLSOURCE_ARCHS generation coccinelle: deref_null: improve performance coccinelle: mini_lock: improve performance powerpc: Allow LD_DEAD_CODE_DATA_ELIMINATION to be selected kbuild: Allow LD_DEAD_CODE_DATA_ELIMINATION to be selectable if enabled kbuild: LD_DEAD_CODE_DATA_ELIMINATION no -ffunction-sections/-fdata-sections for module build kbuild: Fix asm-generic/vmlinux.lds.h for LD_DEAD_CODE_DATA_ELIMINATION modpost: constify *modname function argument where possible modpost: remove redundant is_vmlinux() test modpost: use strstarts() helper more widely modpost: pass struct elf_info pointer to get_modinfo() checkpatch: remove VMLINUX_SYMBOL() check vmlinux.lds.h: remove no-op macro VMLINUX_SYMBOL() kbuild: remove CONFIG_HAVE_UNDERSCORE_SYMBOL_PREFIX export.h: remove code for prefixing symbols with underscore depmod.sh: remove symbol prefix support ...
| * | | | powerpc: Allow LD_DEAD_CODE_DATA_ELIMINATION to be selectedNicholas Piggin2018-05-171-11/+11
| |/ / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This requires further changes to linker script to KEEP some tables and wildcard compiler generated sections into the right place. This includes pp32 modifications from Christophe Leroy. When compiling powernv_defconfig with this option, the resulting kernel is almost 400kB smaller (and still boots): text data bss dec filename 11827621 4810490 1341080 17979191 vmlinux 11752437 4598858 1338776 17690071 vmlinux.dcde Mathieu's numbers for custom Mac Mini G4 config has almost 200kB saving. It also had some increase in vmlinux size for as-yet unknown reasons. text data bss dec filename 7461457 2475122 1428064 11364643 vmlinux 7386425 2364370 1425432 11176227 vmlinux.dcde Tested-by: Christophe Leroy <christophe.leroy@c-s.fr> [8xx] Tested-by: Mathieu Malaterre <malat@debian.org> [32-bit powermac] Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | | | Merge branch 'timers-core-for-linus' of ↵Linus Torvalds2018-06-041-1/+1
|\ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull timers and timekeeping updates from Thomas Gleixner: - Core infrastucture work for Y2038 to address the COMPAT interfaces: + Add a new Y2038 safe __kernel_timespec and use it in the core code + Introduce config switches which allow to control the various compat mechanisms + Use the new config switch in the posix timer code to control the 32bit compat syscall implementation. - Prevent bogus selection of CPU local clocksources which causes an endless reselection loop - Remove the extra kthread in the clocksource code which has no value and just adds another level of indirection - The usual bunch of trivial updates, cleanups and fixlets all over the place - More SPDX conversions * 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits) clocksource/drivers/mxs_timer: Switch to SPDX identifier clocksource/drivers/timer-imx-tpm: Switch to SPDX identifier clocksource/drivers/timer-imx-gpt: Switch to SPDX identifier clocksource/drivers/timer-imx-gpt: Remove outdated file path clocksource/drivers/arc_timer: Add comments about locking while read GFRC clocksource/drivers/mips-gic-timer: Add pr_fmt and reword pr_* messages clocksource/drivers/sprd: Fix Kconfig dependency clocksource: Move inline keyword to the beginning of function declarations timer_list: Remove unused function pointer typedef timers: Adjust a kernel-doc comment tick: Prefer a lower rating device only if it's CPU local device clocksource: Remove kthread time: Change nanosleep to safe __kernel_* types time: Change types to new y2038 safe __kernel_* types time: Fix get_timespec64() for y2038 safe compat interfaces time: Add new y2038 safe __kernel_timespec posix-timers: Make compat syscalls depend on CONFIG_COMPAT_32BIT_TIME time: Introduce CONFIG_COMPAT_32BIT_TIME time: Introduce CONFIG_64BIT_TIME in architectures compat: Enable compat_get/put_timespec64 always ...
| * | | | Merge branch 'timers/urgent' into timers/coreThomas Gleixner2018-05-025-15/+59
| |\| | | | | | | | | | | | | | | | | | Pick up urgent fixes to apply dependent cleanup patch
| * | | | compat: Move compat_timespec/ timeval to compat_time.hDeepa Dinamani2018-04-191-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | All the current architecture specific defines for these are the same. Refactor these common defines to a common header file. The new common linux/compat_time.h is also useful as it will eventually be used to hold all the defines that are needed for compat time types that support non y2038 safe types. New architectures need not have to define these new types as they will only use new y2038 safe syscalls. This file can be deleted after y2038 when we stop supporting non y2038 safe syscalls. The patch also requires an operation similar to: git grep "asm/compat\.h" | cut -d ":" -f 1 | xargs -n 1 sed -i -e "s%asm/compat.h%linux/compat.h%g" Cc: acme@kernel.org Cc: benh@kernel.crashing.org Cc: borntraeger@de.ibm.com Cc: catalin.marinas@arm.com Cc: cmetcalf@mellanox.com Cc: cohuck@redhat.com Cc: davem@davemloft.net Cc: deller@gmx.de Cc: devel@driverdev.osuosl.org Cc: gerald.schaefer@de.ibm.com Cc: gregkh@linuxfoundation.org Cc: heiko.carstens@de.ibm.com Cc: hoeppner@linux.vnet.ibm.com Cc: hpa@zytor.com Cc: jejb@parisc-linux.org Cc: jwi@linux.vnet.ibm.com Cc: linux-kernel@vger.kernel.org Cc: linux-mips@linux-mips.org Cc: linux-parisc@vger.kernel.org Cc: linuxppc-dev@lists.ozlabs.org Cc: linux-s390@vger.kernel.org Cc: mark.rutland@arm.com Cc: mingo@redhat.com Cc: mpe@ellerman.id.au Cc: oberpar@linux.vnet.ibm.com Cc: oprofile-list@lists.sf.net Cc: paulus@samba.org Cc: peterz@infradead.org Cc: ralf@linux-mips.org Cc: rostedt@goodmis.org Cc: rric@kernel.org Cc: schwidefsky@de.ibm.com Cc: sebott@linux.vnet.ibm.com Cc: sparclinux@vger.kernel.org Cc: sth@linux.vnet.ibm.com Cc: ubraun@linux.vnet.ibm.com Cc: will.deacon@arm.com Cc: x86@kernel.org Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com> Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Acked-by: Catalin Marinas <catalin.marinas@arm.com> Acked-by: James Hogan <jhogan@kernel.org> Acked-by: Helge Deller <deller@gmx.de> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* | | | | Merge branch 'siginfo-linus' of ↵Linus Torvalds2018-06-042-7/+7
|\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace Pull siginfo updates from Eric Biederman: "This set of changes close the known issues with setting si_code to an invalid value, and with not fully initializing struct siginfo. There remains work to do on nds32, arc, unicore32, powerpc, arm, arm64, ia64 and x86 to get the code that generates siginfo into a simpler and more maintainable state. Most of that work involves refactoring the signal handling code and thus careful code review. Also not included is the work to shrink the in kernel version of struct siginfo. That depends on getting the number of places that directly manipulate struct siginfo under control, as it requires the introduction of struct kernel_siginfo for the in kernel things. Overall this set of changes looks like it is making good progress, and with a little luck I will be wrapping up the siginfo work next development cycle" * 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (46 commits) signal/sh: Stop gcc warning about an impossible case in do_divide_error signal/mips: Report FPE_FLTUNK for undiagnosed floating point exceptions signal/um: More carefully relay signals in relay_signal. signal: Extend siginfo_layout with SIL_FAULT_{MCEERR|BNDERR|PKUERR} signal: Remove unncessary #ifdef SEGV_PKUERR in 32bit compat code signal/signalfd: Add support for SIGSYS signal/signalfd: Remove __put_user from signalfd_copyinfo signal/xtensa: Use force_sig_fault where appropriate signal/xtensa: Consistenly use SIGBUS in do_unaligned_user signal/um: Use force_sig_fault where appropriate signal/sparc: Use force_sig_fault where appropriate signal/sparc: Use send_sig_fault where appropriate signal/sh: Use force_sig_fault where appropriate signal/s390: Use force_sig_fault where appropriate signal/riscv: Replace do_trap_siginfo with force_sig_fault signal/riscv: Use force_sig_fault where appropriate signal/parisc: Use force_sig_fault where appropriate signal/parisc: Use force_sig_mceerr where appropriate signal/openrisc: Use force_sig_fault where appropriate signal/nios2: Use force_sig_fault where appropriate ...
| * | | | | signal/powerpc: Replace TRAP_FIXME with TRAP_UNKEric W. Biederman2018-04-251-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Using an si_code of 0 that aliases with SI_USER is clearly the wrong thing todo, and causes problems in interesting ways. For use in unknown_exception the recently defined TRAP_UNK semantically is a perfect fit. For use in RunModeException it looks like something more specific than TRAP_UNK could be used. No one has bothered to find a better fit than the broken si_code of 0 in all of these years and I don't see an obvious better fit so TRAP_UNK is switching RunModeException to return TRAP_UNK is clearly an improvement. Recent history suggests no actually cares about crazy corner cases of the kernel behavior like this so I don't expect any regressions from changing this. However if something does happen this change is easy to revert. Though I wonder if SIGKILL might not be a better fit. Cc: Paul Mackerras <paulus@samba.org> Cc: Kumar Gala <kumar.gala@freescale.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: linuxppc-dev@lists.ozlabs.org Fixes: 9bad068c24d7 ("[PATCH] ppc32: support for e500 and 85xx") Fixes: 0ed70f6105ef ("PPC32: Provide proper siginfo information on various exceptions.") History Tree: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
| * | | | | signal/powerpc: Replace FPE_FIXME with FPE_FLTUNKEric W. Biederman2018-04-251-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Using an si_code of 0 that aliases with SI_USER is clearly the wrong thing todo, and causes problems in interesting ways. The newly defined FPE_FLTUNK semantically appears to fit the bill so use it instead. Cc: Paul Mackerras <paulus@samba.org> Cc: Kumar Gala <kumar.gala@freescale.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: linuxppc-dev@lists.ozlabs.org Fixes: 9bad068c24d7 ("[PATCH] ppc32: support for e500 and 85xx") Fixes: 0ed70f6105ef ("PPC32: Provide proper siginfo information on various exceptions.") History Tree: https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
| * | | | | signal: Ensure every siginfo we send has all bits initializedEric W. Biederman2018-04-252-2/+2
| |/ / / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Call clear_siginfo to ensure every stack allocated siginfo is properly initialized before being passed to the signal sending functions. Note: It is not safe to depend on C initializers to initialize struct siginfo on the stack because C is allowed to skip holes when initializing a structure. The initialization of struct siginfo in tracehook_report_syscall_exit was moved from the helper user_single_step_siginfo into tracehook_report_syscall_exit itself, to make it clear that the local variable siginfo gets fully initialized. In a few cases the scope of struct siginfo has been reduced to make it clear that siginfo siginfo is not used on other paths in the function in which it is declared. Instances of using memset to initialize siginfo have been replaced with calls clear_siginfo for clarity. Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
* | | | | Merge tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mappingLinus Torvalds2018-06-041-3/+0
|\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull dma-mapping updates from Christoph Hellwig: - replace the force_dma flag with a dma_configure bus method. (Nipun Gupta, although one patch is іncorrectly attributed to me due to a git rebase bug) - use GFP_DMA32 more agressively in dma-direct. (Takashi Iwai) - remove PCI_DMA_BUS_IS_PHYS and rely on the dma-mapping API to do the right thing for bounce buffering. - move dma-debug initialization to common code, and apply a few cleanups to the dma-debug code. - cleanup the Kconfig mess around swiotlb selection - swiotlb comment fixup (Yisheng Xie) - a trivial swiotlb fix. (Dan Carpenter) - support swiotlb on RISC-V. (based on a patch from Palmer Dabbelt) - add a new generic dma-noncoherent dma_map_ops implementation and use it for arc, c6x and nds32. - improve scatterlist validity checking in dma-debug. (Robin Murphy) - add a struct device quirk to limit the dma-mask to 32-bit due to bridge/system issues, and switch x86 to use it instead of a local hack for VIA bridges. - handle devices without a dma_mask more gracefully in the dma-direct code. * tag 'dma-mapping-4.18' of git://git.infradead.org/users/hch/dma-mapping: (48 commits) dma-direct: don't crash on device without dma_mask nds32: use generic dma_noncoherent_ops nds32: implement the unmap_sg DMA operation nds32: consolidate DMA cache maintainance routines x86/pci-dma: switch the VIA 32-bit DMA quirk to use the struct device flag x86/pci-dma: remove the explicit nodac and allowdac option x86/pci-dma: remove the experimental forcesac boot option Documentation/x86: remove a stray reference to pci-nommu.c core, dma-direct: add a flag 32-bit dma limits dma-mapping: remove unused gfp_t parameter to arch_dma_alloc_attrs dma-debug: check scatterlist segments c6x: use generic dma_noncoherent_ops arc: use generic dma_noncoherent_ops arc: fix arc_dma_{map,unmap}_page arc: fix arc_dma_sync_sg_for_{cpu,device} arc: simplify arc_dma_sync_single_for_{cpu,device} dma-mapping: provide a generic dma-noncoherent implementation dma-mapping: simplify Kconfig dependencies riscv: add swiotlb support riscv: only enable ZONE_DMA32 for 64-bit ...
| * | | | | dma-debug: move initialization to common codeChristoph Hellwig2018-05-081-3/+0
| | |/ / / | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Most mainstream architectures are using 65536 entries, so lets stick to that. If someone is really desperate to override it that can still be done through <asm/dma-mapping.h>, but I'd rather see a really good rationale for that. dma_debug_init is now called as a core_initcall, which for many architectures means much earlier, and provides dma-debug functionality earlier in the boot process. This should be safe as it only relies on the memory allocator already being available. Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Marek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: Robin Murphy <robin.murphy@arm.com>
* | | | | Merge branch 'hch.procfs' of ↵Linus Torvalds2018-06-042-41/+5
|\ \ \ \ \ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull procfs updates from Al Viro: "Christoph's proc_create_... cleanups series" * 'hch.procfs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (44 commits) xfs, proc: hide unused xfs procfs helpers isdn/gigaset: add back gigaset_procinfo assignment proc: update SIZEOF_PDE_INLINE_NAME for the new pde fields tty: replace ->proc_fops with ->proc_show ide: replace ->proc_fops with ->proc_show ide: remove ide_driver_proc_write isdn: replace ->proc_fops with ->proc_show atm: switch to proc_create_seq_private atm: simplify procfs code bluetooth: switch to proc_create_seq_data netfilter/x_tables: switch to proc_create_seq_private netfilter/xt_hashlimit: switch to proc_create_{seq,single}_data neigh: switch to proc_create_seq_data hostap: switch to proc_create_{seq,single}_data bonding: switch to proc_create_seq_data rtc/proc: switch to proc_create_single_data drbd: switch to proc_create_single resource: switch to proc_create_seq_data staging/rtl8192u: simplify procfs code jfs: simplify procfs code ...
| * | | | | proc: introduce proc_create_single{,_data}Christoph Hellwig2018-05-162-41/+5
| |/ / / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Variants of proc_create{,_data} that directly take a seq_file show callback and drastically reduces the boilerplate code in the callers. All trivial callers converted over. Signed-off-by: Christoph Hellwig <hch@lst.de>
* | | | | Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds2018-05-261-0/+1
|\ \ \ \ \ | | |_|_|/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pull KVM fixes from Radim Krčmář: "PPC: - Close a hole which could possibly lead to the host timebase getting out of sync. - Three fixes relating to PTEs and TLB entries for radix guests. - Fix a bug which could lead to an interrupt never getting delivered to the guest, if it is pending for a guest vCPU when the vCPU gets offlined. s390: - Fix false negatives in VSIE validity check (Cc stable) x86: - Fix time drift of VMX preemption timer when a guest uses LAPIC timer in periodic mode (Cc stable) - Unconditionally expose CPUID.IA32_ARCH_CAPABILITIES to allow migration from hosts that don't need retpoline mitigation (Cc stable) - Fix guest crashes on reboot by properly coupling CR4.OSXSAVE and CPUID.OSXSAVE (Cc stable) - Report correct RIP after Hyper-V hypercall #UD (introduced in -rc6)" * tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: x86: fix #UD address of failed Hyper-V hypercalls kvm: x86: IA32_ARCH_CAPABILITIES is always supported KVM: x86: Update cpuid properly when CR4.OSXAVE or CR4.PKE is changed x86/kvm: fix LAPIC timer drift when guest uses periodic mode KVM: s390: vsie: fix < 8k check for the itdba KVM: PPC: Book 3S HV: Do ptesync in radix guest exit path KVM: PPC: Book3S HV: XIVE: Resend re-routed interrupts on CPU priority change KVM: PPC: Book3S HV: Make radix clear pte when unmapping KVM: PPC: Book3S HV: Make radix use correct tlbie sequence in kvmppc_radix_tlbie_page KVM: PPC: Book3S HV: Snapshot timebase offset on guest entry
| * | | | KVM: PPC: Book3S HV: Snapshot timebase offset on guest entryPaul Mackerras2018-05-171-0/+1
| |/ / / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, the HV KVM guest entry/exit code adds the timebase offset from the vcore struct to the timebase on guest entry, and subtracts it on guest exit. Which is fine, except that it is possible for userspace to change the offset using the SET_ONE_REG interface while the vcore is running, as there is only one timebase offset per vcore but potentially multiple VCPUs in the vcore. If that were to happen, KVM would subtract a different offset on guest exit from that which it had added on guest entry, leading to the timebase being out of sync between cores in the host, which then leads to bad things happening such as hangs and spurious watchdog timeouts. To fix this, we add a new field 'tb_offset_applied' to the vcore struct which stores the offset that is currently applied to the timebase. This value is set from the vcore tb_offset field on guest entry, and is what is subtracted from the timebase on guest exit. Since it is zero when the timebase offset is not applied, we can simplify the logic in kvmhv_start_timing and kvmhv_accumulate_time. In addition, we had secondary threads reading the timebase while running concurrently with code on the primary thread which would eventually add or subtract the timebase offset from the timebase. This occurred while saving or restoring the DEC register value on the secondary threads. Although no specific incorrect behaviour has been observed, this is a race which should be fixed. To fix it, we move the DEC saving code to just before we call kvmhv_commence_exit, and the DEC restoring code to after the point where we have waited for the primary thread to switch the MMU context and add the timebase offset. That way we are sure that the timebase contains the guest timebase value in both cases. Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
* | | | Merge tag 'powerpc-4.17-7' of ↵Linus Torvalds2018-05-252-0/+7
|\ \ \ \ | | |_|/ | |/| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc fix from Michael Ellerman: "Just one fix, to make sure the PCR (Processor Compatibility Register) is reset on boot. Otherwise if we're running in compat mode in a guest (eg. pretending a Power9 is a Power8) and the host kernel oopses and kdumps then the kdump kernel's userspace will be running in Power8 mode, and will SIGILL if it uses Power9-only instructions. Thanks to Michael Neuling" * tag 'powerpc-4.17-7' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: powerpc/64s: Clear PCR on boot
| * | | powerpc/64s: Clear PCR on bootMichael Neuling2018-05-182-0/+7
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Clear the PCR (Processor Compatibility Register) on boot to ensure we are not running in a compatibility mode. We've seen this cause problems when a crash (and kdump) occurs while running compat mode guests. The kdump kernel then runs with the PCR set and causes problems. The symptom in the kdump kernel (also seen in petitboot after fast-reboot) is early userspace programs taking sigills on newer instructions (seen in libc). Signed-off-by: Michael Neuling <mikey@neuling.org> Cc: stable@vger.kernel.org Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
* / / powerpc/64s: Add support for a store forwarding barrier at kernel entry/exitNicholas Piggin2018-05-213-2/+180
|/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | On some CPUs we can prevent a vulnerability related to store-to-load forwarding by preventing store forwarding between privilege domains, by inserting a barrier in kernel entry and exit paths. This is known to be the case on at least Power7, Power8 and Power9 powerpc CPUs. Barriers must be inserted generally before the first load after moving to a higher privilege, and after the last store before moving to a lower privilege, HV and PR privilege transitions must be protected. Barriers are added as patch sections, with all kernel/hypervisor entry points patched, and the exit points to lower privilge levels patched similarly to the RFI flush patching. Firmware advertisement is not implemented yet, so CPU flush types are hard coded. Thanks to Michal Suchánek for bug fixes and review. Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com> Signed-off-by: Michael Neuling <mikey@neuling.org> Signed-off-by: Michal Suchánek <msuchanek@suse.de> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* | powerpc: Fix deadlock with multiple calls to smp_send_stopNicholas Piggin2018-04-271-16/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | smp_send_stop can lock up the IPI path for any subsequent calls, because the receiving CPUs spin in their handler function. This started becoming a problem with the addition of an smp_send_stop call in the reboot path, because panics can reboot after doing their own smp_send_stop. The NMI IPI variant was fixed with ac61c11566 ("powerpc: Fix smp_send_stop NMI IPI handling"), which leaves the smp_call_function variant. This is fixed by having smp_send_stop only ever do the smp_call_function once. This is a bit less robust than the NMI IPI fix, because any other call to smp_call_function after smp_send_stop could deadlock, but that has always been the case, and it was not been a problem before. Fixes: f2748bdfe1573 ("powerpc/powernv: Always stop secondaries before reboot/shutdown") Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com> Signed-off-by: Nicholas Piggin <npiggin@gmail.com> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
OpenPOWER on IntegriCloud