summaryrefslogtreecommitdiffstats
path: root/arch/arm/mach-omap2/board-2430sdp.c
Commit message (Collapse)AuthorAgeFilesLines
* omap: mmc: extended to pass host capabilities from board fileSukumar Ghorai2010-09-271-1/+2
| | | | | | | | | wires variable is renamed, extended and this single variable to be used to pass the platform capabilities, e.g DDR mode. Also removed the hardcoded value was using as bus-width. Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* Merge branch 'devel-map-io' into omap-for-linusTony Lindgren2010-08-041-0/+1
|\
| * ARM: OMAP: Convert to use ->reserve method to reserve boot time memoryRussell King2010-07-161-0/+1
| | | | | | | | Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* | Merge branch 'devel-misc' into omap-for-linusTony Lindgren2010-08-021-5/+1
|\ \
| * | omap2: Fix GPIO numbers and smc91x for 2430sdpTony Lindgren2010-08-021-5/+1
| |/ | | | | | | | | | | | | | | Fix GPIO numbers and smc91x for 2430sdp. The earlier code had cut and paste errors from 3430sdp code. Also, 2430 has five GPIO banks for a total of 160 GPIO lines. Signed-off-by: Tony Lindgren <tony@atomide.com>
* | omap: mux: Mux 2430 USB0HS_STP in board-2430.cTony Lindgren2010-07-051-1/+3
| | | | | | | | | | | | | | | | | | Use new mux functions for that. There are no other known 2430 boards that need this mux. Cc: Felipe Balbi <felipe.balbi@nokia.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
* | omap: mux: Select POP package for 2430SDPTony Lindgren2010-07-051-0/+11
| | | | | | | | | | | | Select POP package for 2430SDP Signed-off-by: Tony Lindgren <tony@atomide.com>
* | omap: Move omap2 FS USB platform init code into mach-omap2/usb-fs.cTony Lindgren2010-07-051-1/+1
|/ | | | | | | | | Move omap2 FS USB platform init code into mach-omap2/usb-fs.c. This will allow further work later on to use omap hwmod for initializing the device. Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap2: Add OHCI USB platform init for 2430 SDPViral Mehta2010-05-201-0/+10
| | | | | | | | Add platform init code for OHCI USB on OMAP2430 SDP Signed-off-by: Viral Mehta <viral.mehta@lntinfotech.com> [tony@atomide.com: Updated subject to mention the board name] Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap2: Add I2C bus 1 initialisation for 2430sdpViral Mehta2010-05-201-1/+10
| | | | | | | | Initialize isp1301 FS USB transceiver and add I2C bus1 initialization code for OMAP2430 SDP Signed-off-by: Viral Mehta <viral.mehta@lntinfotech.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap: musb: Pass board specific data from board fileMaulik Mankad2010-02-191-1/+7
| | | | | | | | | | | | | | | | | | Pass board specific data for MUSB (like interface_type, mode etc) from board file by defining board specific structure. Each board file can define this structure based on its requirement and pass this information to the driver. Signed-off-by: Maulik Mankad <x0082077@ti.com> Cc: Tony Lindgren <tony@atomide.com> Cc: Felipe Balbi <felipe.balbi@nokia.com> Cc: David Brownell <david-b@pacbell.net> Cc: Greg Kroah-Hartman <gregkh@suse.de> Cc: Gupta Ajay Kumar <ajay.gupta@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap: Rename hsmmc symbols to reflect independence from twl4030Adrian Hunter2010-02-151-2/+2
| | | | | | | | hsmmc.[ch] no longer has any dependency on twl4030 and variable names should be renamed to reflect that. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap: Rename mmc-twl4030 files to hsmmcAdrian Hunter2010-02-151-1/+1
| | | | | | | | mmc-twl4030.[ch] no longer has any dependency on twl4030 and should be renamed to reflect that. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap: convert boards to use physmap-flashLadislav Michl2010-02-151-4/+3
| | | | | | | | | Convert OMAP based boards to use physmap-flash. Refreshed against today's Linux omap kernel tree Cc: linux-mtd@lists.infradead.org Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap2/3/4: Fix omap2_map_common_io for multi-omapTony Lindgren2010-02-151-1/+1
| | | | | | Fix omap2_map_common_io for multi-omap Signed-off-by: Tony Lindgren <tony@atomide.com>
* mfd: Rename twl4030* driver files to enable re-useSantosh Shilimkar2009-12-131-1/+1
| | | | | | | | | | | | | | | The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030 for OMAP3. The common modules like RTC, Regulator creates opportunity to re-use the most of the code from twl4030. This patch renames few common drivers twl4030* files to twl* to enable the code re-use. Signed-off-by: Rajendra Nayak <rnayak@ti.com> Signed-off-by: Balaji T K <balajitk@ti.com> Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Acked-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* omap: headers: Move remaining headers from include/mach to include/platTony Lindgren2009-10-201-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Move the remaining headers under plat-omap/include/mach to plat-omap/include/plat. Also search and replace the files using these headers to include using the right path. This was done with: #!/bin/bash mach_dir_old="arch/arm/plat-omap/include/mach" plat_dir_new="arch/arm/plat-omap/include/plat" headers=$(cd $mach_dir_old && ls *.h) omap_dirs="arch/arm/*omap*/ \ drivers/video/omap \ sound/soc/omap" other_files="drivers/leds/leds-ams-delta.c \ drivers/mfd/menelaus.c \ drivers/mfd/twl4030-core.c \ drivers/mtd/nand/ams-delta.c" for header in $headers; do old="#include <mach\/$header" new="#include <plat\/$header" for dir in $omap_dirs; do find $dir -type f -name \*.[chS] | \ xargs sed -i "s/$old/$new/" done find drivers/ -type f -name \*omap*.[chS] | \ xargs sed -i "s/$old/$new/" for file in $other_files; do sed -i "s/$old/$new/" $file done done for header in $(ls $mach_dir_old/*.h); do git mv $header $plat_dir_new/ done Signed-off-by: Tony Lindgren <tony@atomide.com>
* omap: Fix DEBUG_LL UART io addressSantosh Shilimkar2009-10-191-1/+1
| | | | | | | | This patch fixes the low level debug UART io address as per this series. The change is essential to have CONFIG_DEBUG_LL working. Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* OMAP2/3 board-*.c files: read bootloader configuration earlierPaul Walmsley2009-09-031-7/+6
| | | | | | | | | | | | | Most board-*.c files read configuration data from the bootloader in their .init_machine() function. This needs to happen earlier, at some point before omap2_init_common_hw() is called. This is because a future patch will use the bootloader serial console port information to enable the UART clocks earlier, immediately after omap2_clk_init(). This is in turn necessary since otherwise clock tree usecounts on clocks like dpll4_m2x2_ck will be bogus, which can cause the currently-active console UART clock to be disabled during boot. Signed-off-by: Paul Walmsley <paul@pwsan.com>
* OMAP: UART: drop OMAP_TAG_UART, enable all UARTs, auto-disabled on idleKalle Valo2009-08-281-5/+0
| | | | | | | | | | | | | | | | OMAP tags are deprecrated so drop them. Drop UART config data which decides which UARTs to enable during boot. This is no longer necessary since serial core code disables clocks after inactivity. Background: with new UART idle code, all on-chip UARTs are idled using a configurable inactivity timer (default 5 seconds.) After the inactivity timer, UART clocks are disabled automatically. Signed-off-by: Kalle Valo <kalle.valo@iki.fi> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* OMAP3 SDRC: add support for 2 SDRAM chip selectsJean Pihet2009-07-241-1/+1
| | | | | | | | | | | | | | | | | | | | | | Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2 SDRAM parts connected to the SDRC. This patch adds the following: - add a new argument of type omap_sdrc_params struct* to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params - adapted the OMAP boards files to the new prototype of omap2_init_common_hw - add the SDRC 2nd CS registers offsets defines - adapt the sram sleep code to configure the SDRC for the 2nd CS Note: If the 2nd param to omap2_init_common_hw is NULL, then the parameters are not programmed into the SDRC CS1 registers Tested on 3430 SDP and Beagleboard rev C2 and B5, with suspend/resume and frequency changes (cpufreq). Signed-off-by: Jean Pihet <jpihet@mvista.com> Signed-off-by: Paul Walmsley <paul@pwsan.com>
* ARM: OMAP2: 2430SDP: Add FB support to board fileImre Deak2009-05-281-0/+19
| | | | | | | | | | | Based on an earlier patch by Hunyue Yau <hyau@mvista.com> with board-*.c changes split to avoid conflicts with other device updates. Cc: linux-fbdev-devel@lists.sourceforge.net Signed-off-by: Hunyue Yau <hyau@mvista.com> Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Signed-off-by: Imre Deak <imre.deak@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: OMAP2/3: Add generic smc91x support when connected to GPMCTony Lindgren2009-05-281-81/+22
| | | | | | | | | | | | | Convert the board-rx51 smc91x code to be generic and make the boards to use it. This allows future recalculation of the timings when the source clock gets scaled. Also correct the rx51 interrupt to be IORESOURCE_IRQ_HIGHLEVEL. Thanks to Paul Walmsley <paul@pwsan.com> for better GPMC timing calculations. Signed-off-by: Tony Lindgren <tony@atomide.com>
* Merge branch 'for-next' of ↵Russell King2009-03-251-5/+10
|\ | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into devel
| * ARM: OMAP3: MUSB initialization for omap hw, v2Felipe Balbi2009-03-231-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Create a generic board-file for initializing usb on omap2430 and omap3 boards. Patch modified by Tony to build the module based on CONFIG_USB_MUSB_SOC. Also merged in a patch adding the nop xceiv from Ajay Kumar Gupta <ajay.gupta@ti.com>. Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
| * ARM: OMAP: No need to include board-omap2430sdp.h from hardware.hTony Lindgren2009-03-231-5/+8
| | | | | | | | | | | | | | | | Move the defines to the associated board file and remove the now unnecessary header file. Also rename SDP2430_ETHR_GPIO_IRQ to SDP2430_ETHR_GPIO_IRQ. Signed-off-by: Tony Lindgren <tony@atomide.com>
* | [ARM] OMAP2 SDRC: add SDRAM timing parameter infrastructurePaul Walmsley2009-02-081-1/+1
|/ | | | | | | | | | | | | | | | | | | | | | | For a given SDRAM clock rate, SDRAM chips require memory controllers to use a specific set of timing minimums and maximums to transfer data reliably. These parameters can be different for different memory chips and can also potentially vary by board. This patch adds the infrastructure for board-*.c files to pass this timing data to the SDRAM controller init function. The timing data is specified in an 'omap_sdrc_params' structure, in terms of SDRC controller register values. An array of these structs, one per SDRC target clock rate, is passed by the board-*.c file to omap2_init_common_hw(). This patch does not define the values for different memory chips, nor does it use the values for anything; those will come in subsequent patches. linux-omap source commit is bc84ecfc795c2d1c5cda8da4127cf972f488a696. Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* omap mmc: Add low-level initialization for hsmmc controllerTony Lindgren2008-12-101-0/+48
| | | | | | | | | | | | | | | | | | | | | | | Add low-level initialization for hsmmc controller. Merged into this patch patch are various improvments and board support by Grazvydas Ignotas and David Brownell. Also change wire4 to be wires, as some newer controllers support 8 data lines. Cc: Pierre Ossman <drzeus-mmc@drzeus.cx> Signed-off-by: Grazvydas Ignotas <notasas@gmail.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: OMAP: Switch to gpio_request/free callsJarkko Nikula2008-12-101-1/+1
| | | | | | | | | | Switch to gpio_request/free calls Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: OMAP: switch to gpio_direction_inputDavid Brownell2008-12-101-1/+1
| | | | | | | | More switchover to the cross-platform GPIO interface: use gpio_direction_input(), not an OMAP-specific call. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Tony Lindgren <tony@atomide.com>
* Merge branch 'ptebits' into develRussell King2008-10-091-1/+1
|\ | | | | | | | | | | Conflicts: arch/arm/Kconfig
| * [ARM] OMAP: Fix 2430 SMC91x ethernet IRQRussell King2008-08-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | Taken from omap 97b705ad835f1481270c4b67b402d6e37fa8ad15: ARM: OMAP: Misc compile fixes after syncing with mainline Also fix 2430 smc91x to use IRQ_LOWLEVEL. Signed-off-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* | [ARM] Convert asm/io.h to linux/io.hRussell King2008-09-061-2/+1
|/ | | | Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* [ARM] Move include/asm-arm/arch-* to arch/arm/*/include/machRussell King2008-08-071-6/+6
| | | | | | This just leaves include/asm-arm/plat-* to deal with. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* [ARM] Remove asm/hardware.h, use asm/arch/hardware.h insteadRussell King2008-08-071-1/+1
| | | | | | | | | Remove includes of asm/hardware.h in addition to asm/arch/hardware.h. Then, since asm/hardware.h only exists to include asm/arch/hardware.h, update everything to directly include asm/arch/hardware.h and remove asm/hardware.h. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* ARM: OMAP: Add calls to omap2_set_globals_*()Paul Walmsley2008-05-091-0/+1
| | | | | | | | | | | | | | Add the omap2_set_globals_{242x,243x,343x}() functions. These functions are called early upon boot in the map_io() functions in the board-specific init files. This patch was accidentally left out of the earlier series. This fixes omap2 booting as noted by Kyungmin Park <kmpark@infradead.org>. Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Kyungmin Park <kmpark@infradead.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
* ARM: OMAP2: Change 24xx to use new register accessPaul Walmsley2008-04-141-9/+14
| | | | | | | | | | | | | | | | | | | This patch changes 24xx to use new register access, except for clock framework. Clock framework register access will get updates in the next patch. Note that board-*.c files change GPMC (General Purpose Memory Controller) access to use gpmc_cs_write_reg() instead of accessing the registers directly. The code also uses gpmc_fck instead of it's parent clock core_l3_ck for GPMC clock. The H4 board file also adds h4_init_flash() function, which specify the flash start and end addresses. Also note that sleep.S removes some unused registers addresses. Signed-off-by: Paul Walmsley <paul@pwsan.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
* [NET] smc91x: Make smc91x use IRQ resource trigger flagsRussell King2008-01-281-1/+1
| | | | | | | | | | | | | | | | | | | | | | | smc91x is shared between many different platforms. Each platform needs to specify the interrupt type, and in some cases the irq type depends on more than just the build configuration - it depends on runtime checks. Rather than throwing this code into the SMC_IRQ_FLAGS definition, provide a way for these flags to be passed via the IRQ resource itself. Note that IRQF_TRIGGER_* constants are intentionally defined to correspond with the IORESOURCE_IRQ_* interrupt type flags, in much the same way that the low bits of PCI iomem resources correspond with the BAR flag bits. Also provide a way to configure smc91x to read the IRQ flags from the resource. Once all platforms have been converted over (signified by all definitions of SMC_IRQ_FLAGS being -1) SMC_IRQ_FLAGS should be removed. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Acked-by: Nicolas Pitre <nico@cam.org> Acked-by: Jeff Garzik <jgarzik@redhat.com>
* ARM: OMAP: Add minimal OMAP2430 supportSyed Mohammed Khasim2007-09-201-0/+218
This patch adds minimal OMAP2430 support to get the kernel booting on 2430SDP. Signed-off-by: Syed Mohammed Khasim <x0khasim@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
OpenPOWER on IntegriCloud