diff options
Diffstat (limited to 'include/linux/usb')
| -rw-r--r-- | include/linux/usb/musb.h | 98 | ||||
| -rw-r--r-- | include/linux/usb/serial.h | 3 |
2 files changed, 100 insertions, 1 deletions
diff --git a/include/linux/usb/musb.h b/include/linux/usb/musb.h new file mode 100644 index 000000000000..630962c04ca4 --- /dev/null +++ b/include/linux/usb/musb.h @@ -0,0 +1,98 @@ +/* + * This is used to for host and peripheral modes of the driver for + * Inventra (Multidrop) Highspeed Dual-Role Controllers: (M)HDRC. + * + * Board initialization should put one of these into dev->platform_data, + * probably on some platform_device named "musb_hdrc". It encapsulates + * key configuration differences between boards. + */ + +/* The USB role is defined by the connector used on the board, so long as + * standards are being followed. (Developer boards sometimes won't.) + */ +enum musb_mode { + MUSB_UNDEFINED = 0, + MUSB_HOST, /* A or Mini-A connector */ + MUSB_PERIPHERAL, /* B or Mini-B connector */ + MUSB_OTG /* Mini-AB connector */ +}; + +struct clk; + +struct musb_hdrc_eps_bits { + const char name[16]; + u8 bits; +}; + +struct musb_hdrc_config { + /* MUSB configuration-specific details */ + unsigned multipoint:1; /* multipoint device */ + unsigned dyn_fifo:1; /* supports dynamic fifo sizing */ + unsigned soft_con:1; /* soft connect required */ + unsigned utm_16:1; /* utm data witdh is 16 bits */ + unsigned big_endian:1; /* true if CPU uses big-endian */ + unsigned mult_bulk_tx:1; /* Tx ep required for multbulk pkts */ + unsigned mult_bulk_rx:1; /* Rx ep required for multbulk pkts */ + unsigned high_iso_tx:1; /* Tx ep required for HB iso */ + unsigned high_iso_rx:1; /* Rx ep required for HD iso */ + unsigned dma:1; /* supports DMA */ + unsigned vendor_req:1; /* vendor registers required */ + + u8 num_eps; /* number of endpoints _with_ ep0 */ + u8 dma_channels; /* number of dma channels */ + u8 dyn_fifo_size; /* dynamic size in bytes */ + u8 vendor_ctrl; /* vendor control reg width */ + u8 vendor_stat; /* vendor status reg witdh */ + u8 dma_req_chan; /* bitmask for required dma channels */ + u8 ram_bits; /* ram address size */ + + struct musb_hdrc_eps_bits *eps_bits; +}; + +struct musb_hdrc_platform_data { + /* MUSB_HOST, MUSB_PERIPHERAL, or MUSB_OTG */ + u8 mode; + + /* for clk_get() */ + const char *clock; + + /* (HOST or OTG) switch VBUS on/off */ + int (*set_vbus)(struct device *dev, int is_on); + + /* (HOST or OTG) mA/2 power supplied on (default = 8mA) */ + u8 power; + + /* (PERIPHERAL) mA/2 max power consumed (default = 100mA) */ + u8 min_power; + + /* (HOST or OTG) msec/2 after VBUS on till power good */ + u8 potpgt; + + /* Power the device on or off */ + int (*set_power)(int state); + + /* Turn device clock on or off */ + int (*set_clock)(struct clk *clock, int is_on); + + /* MUSB configuration-specific details */ + struct musb_hdrc_config *config; +}; + + +/* TUSB 6010 support */ + +#define TUSB6010_OSCCLK_60 16667 /* psec/clk @ 60.0 MHz */ +#define TUSB6010_REFCLK_24 41667 /* psec/clk @ 24.0 MHz XI */ +#define TUSB6010_REFCLK_19 52083 /* psec/clk @ 19.2 MHz CLKIN */ + +#ifdef CONFIG_ARCH_OMAP2 + +extern int __init tusb6010_setup_interface( + struct musb_hdrc_platform_data *data, + unsigned ps_refclk, unsigned waitpin, + unsigned async_cs, unsigned sync_cs, + unsigned irq, unsigned dmachan); + +extern int tusb6010_platform_retime(unsigned is_refclk); + +#endif /* OMAP2 */ diff --git a/include/linux/usb/serial.h b/include/linux/usb/serial.h index 09a3e6a7518f..655341d0f534 100644 --- a/include/linux/usb/serial.h +++ b/include/linux/usb/serial.h @@ -17,7 +17,8 @@ #include <linux/mutex.h> #define SERIAL_TTY_MAJOR 188 /* Nice legal number now */ -#define SERIAL_TTY_MINORS 255 /* loads of devices :) */ +#define SERIAL_TTY_MINORS 254 /* loads of devices :) */ +#define SERIAL_TTY_NO_MINOR 255 /* No minor was assigned */ /* The maximum number of ports one device can grab at once */ #define MAX_NUM_PORTS 8 |
