diff options
Diffstat (limited to 'drivers/serial/bfin_5xx.c')
| -rw-r--r-- | drivers/serial/bfin_5xx.c | 56 |
1 files changed, 37 insertions, 19 deletions
diff --git a/drivers/serial/bfin_5xx.c b/drivers/serial/bfin_5xx.c index 46bb47f37b9a..5f55534a290b 100644 --- a/drivers/serial/bfin_5xx.c +++ b/drivers/serial/bfin_5xx.c @@ -151,7 +151,8 @@ void kgdb_put_debug_char(int chr) { struct bfin_serial_port *uart; - if (CONFIG_KGDB_UART_PORT<0 || CONFIG_KGDB_UART_PORT>=NR_PORTS) + if (CONFIG_KGDB_UART_PORT < 0 + || CONFIG_KGDB_UART_PORT >= BFIN_UART_NR_PORTS) uart = &bfin_serial_ports[0]; else uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT]; @@ -173,7 +174,8 @@ int kgdb_get_debug_char(void) struct bfin_serial_port *uart; unsigned char chr; - if (CONFIG_KGDB_UART_PORT<0 || CONFIG_KGDB_UART_PORT>=NR_PORTS) + if (CONFIG_KGDB_UART_PORT < 0 + || CONFIG_KGDB_UART_PORT >= BFIN_UART_NR_PORTS) uart = &bfin_serial_ports[0]; else uart = &bfin_serial_ports[CONFIG_KGDB_UART_PORT]; @@ -192,7 +194,7 @@ int kgdb_get_debug_char(void) } #endif -#if ANOMALY_05000230 && defined(CONFIG_SERIAL_BFIN_PIO) +#if ANOMALY_05000363 && defined(CONFIG_SERIAL_BFIN_PIO) # define UART_GET_ANOMALY_THRESHOLD(uart) ((uart)->anomaly_threshold) # define UART_SET_ANOMALY_THRESHOLD(uart, v) ((uart)->anomaly_threshold = (v)) #else @@ -237,7 +239,7 @@ static void bfin_serial_rx_chars(struct bfin_serial_port *uart) } #endif - if (ANOMALY_05000230) { + if (ANOMALY_05000363) { /* The BF533 (and BF561) family of processors have a nice anomaly * where they continuously generate characters for a "single" break. * We have to basically ignore this flood until the "next" valid @@ -249,9 +251,6 @@ static void bfin_serial_rx_chars(struct bfin_serial_port *uart) * timeout was picked as it must absolutely be larger than 1 * character time +/- some percent. So 1.5 sounds good. All other * Blackfin families operate properly. Woo. - * Note: While Anomaly 05000230 does not directly address this, - * the changes that went in for it also fixed this issue. - * That anomaly was fixed in 0.5+ silicon. I like bunnies. */ if (anomaly_start.tv_sec) { struct timeval curr; @@ -285,7 +284,7 @@ static void bfin_serial_rx_chars(struct bfin_serial_port *uart) } if (status & BI) { - if (ANOMALY_05000230) + if (ANOMALY_05000363) if (bfin_revid() < 5) do_gettimeofday(&anomaly_start); uart->port.icount.brk++; @@ -507,8 +506,7 @@ void bfin_serial_rx_dma_timeout(struct bfin_serial_port *uart) uart->rx_dma_buf.tail = uart->rx_dma_buf.head; } - uart->rx_dma_timer.expires = jiffies + DMA_RX_FLUSH_JIFFIES; - add_timer(&(uart->rx_dma_timer)); + mod_timer(&(uart->rx_dma_timer), jiffies + DMA_RX_FLUSH_JIFFIES); } static irqreturn_t bfin_serial_dma_tx_int(int irq, void *dev_id) @@ -551,9 +549,7 @@ static irqreturn_t bfin_serial_dma_rx_int(int irq, void *dev_id) clear_dma_irqstat(uart->rx_dma_channel); spin_unlock(&uart->port.lock); - del_timer(&(uart->rx_dma_timer)); - uart->rx_dma_timer.expires = jiffies; - add_timer(&(uart->rx_dma_timer)); + mod_timer(&(uart->rx_dma_timer), jiffies); return IRQ_HANDLED; } @@ -749,7 +745,7 @@ bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios, struct bfin_serial_port *uart = (struct bfin_serial_port *)port; unsigned long flags; unsigned int baud, quot; - unsigned short val, ier, lsr, lcr = 0; + unsigned short val, ier, lcr = 0; switch (termios->c_cflag & CSIZE) { case CS8: @@ -806,10 +802,6 @@ bfin_serial_set_termios(struct uart_port *port, struct ktermios *termios, UART_SET_ANOMALY_THRESHOLD(uart, USEC_PER_SEC / baud * 15); - do { - lsr = UART_GET_LSR(uart); - } while (!(lsr & TEMT)); - /* Disable UART */ ier = UART_GET_IER(uart); #ifdef CONFIG_BF54x @@ -900,6 +892,31 @@ bfin_serial_verify_port(struct uart_port *port, struct serial_struct *ser) return 0; } +/* + * Enable the IrDA function if tty->ldisc.num is N_IRDA. + * In other cases, disable IrDA function. + */ +static void bfin_set_ldisc(struct tty_struct *tty) +{ + int line = tty->index; + unsigned short val; + + if (line >= tty->driver->num) + return; + + switch (tty->ldisc.num) { + case N_IRDA: + val = UART_GET_GCTL(&bfin_serial_ports[line]); + val |= (IREN | RPOLC); + UART_PUT_GCTL(&bfin_serial_ports[line], val); + break; + default: + val = UART_GET_GCTL(&bfin_serial_ports[line]); + val &= ~(IREN | RPOLC); + UART_PUT_GCTL(&bfin_serial_ports[line], val); + } +} + static struct uart_ops bfin_serial_pops = { .tx_empty = bfin_serial_tx_empty, .set_mctrl = bfin_serial_set_mctrl, @@ -1172,7 +1189,7 @@ static struct uart_driver bfin_serial_reg = { .dev_name = BFIN_SERIAL_NAME, .major = BFIN_SERIAL_MAJOR, .minor = BFIN_SERIAL_MINOR, - .nr = NR_PORTS, + .nr = BFIN_UART_NR_PORTS, .cons = BFIN_SERIAL_CONSOLE, }; @@ -1261,6 +1278,7 @@ static int __init bfin_serial_init(void) ret = uart_register_driver(&bfin_serial_reg); if (ret == 0) { + bfin_serial_reg.tty_driver->set_ldisc = bfin_set_ldisc; ret = platform_driver_register(&bfin_serial_driver); if (ret) { pr_debug("uart register failed\n"); |
