diff options
Diffstat (limited to 'drivers/net/chelsio/vsc7326_reg.h')
| -rw-r--r-- | drivers/net/chelsio/vsc7326_reg.h | 286 |
1 files changed, 286 insertions, 0 deletions
diff --git a/drivers/net/chelsio/vsc7326_reg.h b/drivers/net/chelsio/vsc7326_reg.h new file mode 100644 index 000000000000..491bcf75c4fb --- /dev/null +++ b/drivers/net/chelsio/vsc7326_reg.h @@ -0,0 +1,286 @@ +/* $Date: 2006/04/28 19:20:17 $ $RCSfile: vsc7326_reg.h,v $ $Revision: 1.5 $ */ +#ifndef _VSC7321_REG_H_ +#define _VSC7321_REG_H_ + +/* Register definitions for Vitesse VSC7321 (Meigs II) MAC + * + * Straight off the data sheet, VMDS-10038 Rev 2.0 and + * PD0011-01-14-Meigs-II 2002-12-12 + */ + +/* Just 'cause it's in here doesn't mean it's used. */ + +#define CRA(blk,sub,adr) ((((blk) & 0x7) << 13) | (((sub) & 0xf) << 9) | (((adr) & 0xff) << 1)) + +/* System and CPU comm's registers */ +#define REG_CHIP_ID CRA(0x7,0xf,0x00) /* Chip ID */ +#define REG_BLADE_ID CRA(0x7,0xf,0x01) /* Blade ID */ +#define REG_SW_RESET CRA(0x7,0xf,0x02) /* Global Soft Reset */ +#define REG_MEM_BIST CRA(0x7,0xf,0x04) /* mem */ +#define REG_IFACE_MODE CRA(0x7,0xf,0x07) /* Interface mode */ +#define REG_MSCH CRA(0x7,0x2,0x06) /* CRC error count */ +#define REG_CRC_CNT CRA(0x7,0x2,0x0a) /* CRC error count */ +#define REG_CRC_CFG CRA(0x7,0x2,0x0b) /* CRC config */ +#define REG_SI_TRANSFER_SEL CRA(0x7,0xf,0x18) /* SI Transfer Select */ +#define REG_PLL_CLK_SPEED CRA(0x7,0xf,0x19) /* Clock Speed Selection */ +#define REG_SYS_CLK_SELECT CRA(0x7,0xf,0x1c) /* System Clock Select */ +#define REG_GPIO_CTRL CRA(0x7,0xf,0x1d) /* GPIO Control */ +#define REG_GPIO_OUT CRA(0x7,0xf,0x1e) /* GPIO Out */ +#define REG_GPIO_IN CRA(0x7,0xf,0x1f) /* GPIO In */ +#define REG_CPU_TRANSFER_SEL CRA(0x7,0xf,0x20) /* CPU Transfer Select */ +#define REG_LOCAL_DATA CRA(0x7,0xf,0xfe) /* Local CPU Data Register */ +#define REG_LOCAL_STATUS CRA(0x7,0xf,0xff) /* Local CPU Status Register */ + +/* Aggregator registers */ +#define REG_AGGR_SETUP CRA(0x7,0x1,0x00) /* Aggregator Setup */ +#define REG_PMAP_TABLE CRA(0x7,0x1,0x01) /* Port map table */ +#define REG_MPLS_BIT0 CRA(0x7,0x1,0x08) /* MPLS bit0 position */ +#define REG_MPLS_BIT1 CRA(0x7,0x1,0x09) /* MPLS bit1 position */ +#define REG_MPLS_BIT2 CRA(0x7,0x1,0x0a) /* MPLS bit2 position */ +#define REG_MPLS_BIT3 CRA(0x7,0x1,0x0b) /* MPLS bit3 position */ +#define REG_MPLS_BITMASK CRA(0x7,0x1,0x0c) /* MPLS bit mask */ +#define REG_PRE_BIT0POS CRA(0x7,0x1,0x10) /* Preamble bit0 position */ +#define REG_PRE_BIT1POS CRA(0x7,0x1,0x11) /* Preamble bit1 position */ +#define REG_PRE_BIT2POS CRA(0x7,0x1,0x12) /* Preamble bit2 position */ +#define REG_PRE_BIT3POS CRA(0x7,0x1,0x13) /* Preamble bit3 position */ +#define REG_PRE_ERR_CNT CRA(0x7,0x1,0x14) /* Preamble parity error count */ + +/* BIST registers */ +/*#define REG_RAM_BIST_CMD CRA(0x7,0x2,0x00)*/ /* RAM BIST Command Register */ +/*#define REG_RAM_BIST_RESULT CRA(0x7,0x2,0x01)*/ /* RAM BIST Read Status/Result */ +#define REG_RAM_BIST_CMD CRA(0x7,0x1,0x00) /* RAM BIST Command Register */ +#define REG_RAM_BIST_RESULT CRA(0x7,0x1,0x01) /* RAM BIST Read Status/Result */ +#define BIST_PORT_SELECT 0x00 /* BIST port select */ +#define BIST_COMMAND 0x01 /* BIST enable/disable */ +#define BIST_STATUS 0x02 /* BIST operation status */ +#define BIST_ERR_CNT_LSB 0x03 /* BIST error count lo 8b */ +#define BIST_ERR_CNT_MSB 0x04 /* BIST error count hi 8b */ +#define BIST_ERR_SEL_LSB 0x05 /* BIST error select lo 8b */ +#define BIST_ERR_SEL_MSB 0x06 /* BIST error select hi 8b */ +#define BIST_ERROR_STATE 0x07 /* BIST engine internal state */ +#define BIST_ERR_ADR0 0x08 /* BIST error address lo 8b */ +#define BIST_ERR_ADR1 0x09 /* BIST error address lomid 8b */ +#define BIST_ERR_ADR2 0x0a /* BIST error address himid 8b */ +#define BIST_ERR_ADR3 0x0b /* BIST error address hi 8b */ + +/* FIFO registers + * ie = 0 for ingress, 1 for egress + * fn = FIFO number, 0-9 + */ +#define REG_TEST(ie,fn) CRA(0x2,ie&1,0x00+fn) /* Mode & Test Register */ +#define REG_TOP_BOTTOM(ie,fn) CRA(0x2,ie&1,0x10+fn) /* FIFO Buffer Top & Bottom */ +#define REG_TAIL(ie,fn) CRA(0x2,ie&1,0x20+fn) /* FIFO Write Pointer */ +#define REG_HEAD(ie,fn) CRA(0x2,ie&1,0x30+fn) /* FIFO Read Pointer */ +#define REG_HIGH_LOW_WM(ie,fn) CRA(0x2,ie&1,0x40+fn) /* Flow Control Water Marks */ +#define REG_CT_THRHLD(ie,fn) CRA(0x2,ie&1,0x50+fn) /* Cut Through Threshold */ +#define REG_FIFO_DROP_CNT(ie,fn) CRA(0x2,ie&1,0x60+fn) /* Drop & CRC Error Counter */ +#define REG_DEBUG_BUF_CNT(ie,fn) CRA(0x2,ie&1,0x70+fn) /* Input Side Debug Counter */ +#define REG_BUCKI(fn) CRA(0x2,2,0x20+fn) /* Input Side Debug Counter */ +#define REG_BUCKE(fn) CRA(0x2,3,0x20+fn) /* Input Side Debug Counter */ + +/* Traffic shaper buckets + * ie = 0 for ingress, 1 for egress + * bn = bucket number 0-10 (yes, 11 buckets) + */ +/* OK, this one's kinda ugly. Some hardware designers are perverse. */ +#define REG_TRAFFIC_SHAPER_BUCKET(ie,bn) CRA(0x2,ie&1,0x0a + (bn>7) | ((bn&7)<<4)) +#define REG_TRAFFIC_SHAPER_CONTROL(ie) CRA(0x2,ie&1,0x3b) + +#define REG_SRAM_ADR(ie) CRA(0x2,ie&1,0x0e) /* FIFO SRAM address */ +#define REG_SRAM_WR_STRB(ie) CRA(0x2,ie&1,0x1e) /* FIFO SRAM write strobe */ +#define REG_SRAM_RD_STRB(ie) CRA(0x2,ie&1,0x2e) /* FIFO SRAM read strobe */ +#define REG_SRAM_DATA_0(ie) CRA(0x2,ie&1,0x3e) /* FIFO SRAM data lo 8b */ +#define REG_SRAM_DATA_1(ie) CRA(0x2,ie&1,0x4e) /* FIFO SRAM data lomid 8b */ +#define REG_SRAM_DATA_2(ie) CRA(0x2,ie&1,0x5e) /* FIFO SRAM data himid 8b */ +#define REG_SRAM_DATA_3(ie) CRA(0x2,ie&1,0x6e) /* FIFO SRAM data hi 8b */ +#define REG_SRAM_DATA_BLK_TYPE(ie) CRA(0x2,ie&1,0x7e) /* FIFO SRAM tag */ +/* REG_ING_CONTROL equals REG_CONTROL with ie = 0, likewise REG_EGR_CONTROL is ie = 1 */ +#define REG_CONTROL(ie) CRA(0x2,ie&1,0x0f) /* FIFO control */ +#define REG_ING_CONTROL CRA(0x2,0x0,0x0f) /* Ingress control (alias) */ +#define REG_EGR_CONTROL CRA(0x2,0x1,0x0f) /* Egress control (alias) */ +#define REG_AGE_TIMER(ie) CRA(0x2,ie&1,0x1f) /* Aging timer */ +#define REG_AGE_INC(ie) CRA(0x2,ie&1,0x2f) /* Aging increment */ +#define DEBUG_OUT(ie) CRA(0x2,ie&1,0x3f) /* Output debug counter control */ +#define DEBUG_CNT(ie) CRA(0x2,ie&1,0x4f) /* Output debug counter */ + +/* SPI4 interface */ +#define REG_SPI4_MISC CRA(0x5,0x0,0x00) /* Misc Register */ +#define REG_SPI4_STATUS CRA(0x5,0x0,0x01) /* CML Status */ +#define REG_SPI4_ING_SETUP0 CRA(0x5,0x0,0x02) /* Ingress Status Channel Setup */ +#define REG_SPI4_ING_SETUP1 CRA(0x5,0x0,0x03) /* Ingress Data Training Setup */ +#define REG_SPI4_ING_SETUP2 CRA(0x5,0x0,0x04) /* Ingress Data Burst Size Setup */ +#define REG_SPI4_EGR_SETUP0 CRA(0x5,0x0,0x05) /* Egress Status Channel Setup */ +#define REG_SPI4_DBG_CNT(n) CRA(0x5,0x0,0x10+n) /* Debug counters 0-9 */ +#define REG_SPI4_DBG_SETUP CRA(0x5,0x0,0x1A) /* Debug counters setup */ +#define REG_SPI4_TEST CRA(0x5,0x0,0x20) /* Test Setup Register */ +#define REG_TPGEN_UP0 CRA(0x5,0x0,0x21) /* Test Pattern generator user pattern 0 */ +#define REG_TPGEN_UP1 CRA(0x5,0x0,0x22) /* Test Pattern generator user pattern 1 */ +#define REG_TPCHK_UP0 CRA(0x5,0x0,0x23) /* Test Pattern checker user pattern 0 */ +#define REG_TPCHK_UP1 CRA(0x5,0x0,0x24) /* Test Pattern checker user pattern 1 */ +#define REG_TPSAM_P0 CRA(0x5,0x0,0x25) /* Sampled pattern 0 */ +#define REG_TPSAM_P1 CRA(0x5,0x0,0x26) /* Sampled pattern 1 */ +#define REG_TPERR_CNT CRA(0x5,0x0,0x27) /* Pattern checker error counter */ +#define REG_SPI4_STICKY CRA(0x5,0x0,0x30) /* Sticky bits register */ +#define REG_SPI4_DBG_INH CRA(0x5,0x0,0x31) /* Core egress & ingress inhibit */ +#define REG_SPI4_DBG_STATUS CRA(0x5,0x0,0x32) /* Sampled ingress status */ +#define REG_SPI4_DBG_GRANT CRA(0x5,0x0,0x33) /* Ingress cranted credit value */ + +#define REG_SPI4_DESKEW CRA(0x5,0x0,0x43) /* Ingress cranted credit value */ + +/* 10GbE MAC Block Registers */ +/* Note that those registers that are exactly the same for 10GbE as for + * tri-speed are only defined with the version that needs a port number. + * Pass 0xa in those cases. + * + * Also note that despite the presence of a MAC address register, this part + * does no ingress MAC address filtering. That register is used only for + * pause frame detection and generation. + */ +/* 10GbE specific, and different from tri-speed */ +#define REG_MISC_10G CRA(0x1,0xa,0x00) /* Misc 10GbE setup */ +#define REG_PAUSE_10G CRA(0x1,0xa,0x01) /* Pause register */ +#define REG_NORMALIZER_10G CRA(0x1,0xa,0x05) /* 10G normalizer */ +#define REG_STICKY_RX CRA(0x1,0xa,0x06) /* RX debug register */ +#define REG_DENORM_10G CRA(0x1,0xa,0x07) /* Denormalizer */ +#define REG_STICKY_TX CRA(0x1,0xa,0x08) /* TX sticky bits */ +#define REG_MAX_RXHIGH CRA(0x1,0xa,0x0a) /* XGMII lane 0-3 debug */ +#define REG_MAX_RXLOW CRA(0x1,0xa,0x0b) /* XGMII lane 4-7 debug */ +#define REG_MAC_TX_STICKY CRA(0x1,0xa,0x0c) /* MAC Tx state sticky debug */ +#define REG_MAC_TX_RUNNING CRA(0x1,0xa,0x0d) /* MAC Tx state running debug */ +#define REG_TX_ABORT_AGE CRA(0x1,0xa,0x14) /* Aged Tx frames discarded */ +#define REG_TX_ABORT_SHORT CRA(0x1,0xa,0x15) /* Short Tx frames discarded */ +#define REG_TX_ABORT_TAXI CRA(0x1,0xa,0x16) /* Taxi error frames discarded */ +#define REG_TX_ABORT_UNDERRUN CRA(0x1,0xa,0x17) /* Tx Underrun abort counter */ +#define REG_TX_DENORM_DISCARD CRA(0x1,0xa,0x18) /* Tx denormalizer discards */ +#define REG_XAUI_STAT_A CRA(0x1,0xa,0x20) /* XAUI status A */ +#define REG_XAUI_STAT_B CRA(0x1,0xa,0x21) /* XAUI status B */ +#define REG_XAUI_STAT_C CRA(0x1,0xa,0x22) /* XAUI status C */ +#define REG_XAUI_CONF_A CRA(0x1,0xa,0x23) /* XAUI configuration A */ +#define REG_XAUI_CONF_B CRA(0x1,0xa,0x24) /* XAUI configuration B */ +#define REG_XAUI_CODE_GRP_CNT CRA(0x1,0xa,0x25) /* XAUI code group error count */ +#define REG_XAUI_CONF_TEST_A CRA(0x1,0xa,0x26) /* XAUI test register A */ +#define REG_PDERRCNT CRA(0x1,0xa,0x27) /* XAUI test register B */ + +/* pn = port number 0-9 for tri-speed, 10 for 10GbE */ +/* Both tri-speed and 10GbE */ +#define REG_MAX_LEN(pn) CRA(0x1,pn,0x02) /* Max length */ +#define REG_MAC_HIGH_ADDR(pn) CRA(0x1,pn,0x03) /* Upper 24 bits of MAC addr */ +#define REG_MAC_LOW_ADDR(pn) CRA(0x1,pn,0x04) /* Lower 24 bits of MAC addr */ + +/* tri-speed only + * pn = port number, 0-9 + */ +#define REG_MODE_CFG(pn) CRA(0x1,pn,0x00) /* Mode configuration */ +#define REG_PAUSE_CFG(pn) CRA(0x1,pn,0x01) /* Pause configuration */ +#define REG_NORMALIZER(pn) CRA(0x1,pn,0x05) /* Normalizer */ +#define REG_TBI_STATUS(pn) CRA(0x1,pn,0x06) /* TBI status */ +#define REG_PCS_STATUS_DBG(pn) CRA(0x1,pn,0x07) /* PCS status debug */ +#define REG_PCS_CTRL(pn) CRA(0x1,pn,0x08) /* PCS control */ +#define REG_TBI_CONFIG(pn) CRA(0x1,pn,0x09) /* TBI configuration */ +#define REG_STICK_BIT(pn) CRA(0x1,pn,0x0a) /* Sticky bits */ +#define REG_DEV_SETUP(pn) CRA(0x1,pn,0x0b) /* MAC clock/reset setup */ +#define REG_DROP_CNT(pn) CRA(0x1,pn,0x0c) /* Drop counter */ +#define REG_PORT_POS(pn) CRA(0x1,pn,0x0d) /* Preamble port position */ +#define REG_PORT_FAIL(pn) CRA(0x1,pn,0x0e) /* Preamble port position */ +#define REG_SERDES_CONF(pn) CRA(0x1,pn,0x0f) /* SerDes configuration */ +#define REG_SERDES_TEST(pn) CRA(0x1,pn,0x10) /* SerDes test */ +#define REG_SERDES_STAT(pn) CRA(0x1,pn,0x11) /* SerDes status */ +#define REG_SERDES_COM_CNT(pn) CRA(0x1,pn,0x12) /* SerDes comma counter */ +#define REG_DENORM(pn) CRA(0x1,pn,0x15) /* Frame denormalization */ +#define REG_DBG(pn) CRA(0x1,pn,0x16) /* Device 1G debug */ +#define REG_TX_IFG(pn) CRA(0x1,pn,0x18) /* Tx IFG config */ +#define REG_HDX(pn) CRA(0x1,pn,0x19) /* Half-duplex config */ + +/* Statistics */ +/* pn = port number, 0-a, a = 10GbE */ +#define REG_RX_IN_BYTES(pn) CRA(0x4,pn,0x00) /* # Rx in octets */ +#define REG_RX_SYMBOL_CARRIER(pn) CRA(0x4,pn,0x01) /* Frames w/ symbol errors */ +#define REG_RX_PAUSE(pn) CRA(0x4,pn,0x02) /* # pause frames received */ +#define REG_RX_UNSUP_OPCODE(pn) CRA(0x4,pn,0x03) /* # control frames with unsupported opcode */ +#define REG_RX_OK_BYTES(pn) CRA(0x4,pn,0x04) /* # octets in good frames */ +#define REG_RX_BAD_BYTES(pn) CRA(0x4,pn,0x05) /* # octets in bad frames */ +#define REG_RX_UNICAST(pn) CRA(0x4,pn,0x06) /* # good unicast frames */ +#define REG_RX_MULTICAST(pn) CRA(0x4,pn,0x07) /* # good multicast frames */ +#define REG_RX_BROADCAST(pn) CRA(0x4,pn,0x08) /* # good broadcast frames */ +#define REG_CRC(pn) CRA(0x4,pn,0x09) /* # frames w/ bad CRC only */ +#define REG_RX_ALIGNMENT(pn) CRA(0x4,pn,0x0a) /* # frames w/ alignment err */ +#define REG_RX_UNDERSIZE(pn) CRA(0x4,pn,0x0b) /* # frames undersize */ +#define REG_RX_FRAGMENTS(pn) CRA(0x4,pn,0x0c) /* # frames undersize w/ crc err */ +#define REG_RX_IN_RANGE_LENGTH_ERROR(pn) CRA(0x4,pn,0x0d) /* # frames with length error */ +#define REG_RX_OUT_OF_RANGE_ERROR(pn) CRA(0x4,pn,0x0e) /* # frames with illegal length field */ +#define REG_RX_OVERSIZE(pn) CRA(0x4,pn,0x0f) /* # frames oversize */ +#define REG_RX_JABBERS(pn) CRA(0x4,pn,0x10) /* # frames oversize w/ crc err */ +#define REG_RX_SIZE_64(pn) CRA(0x4,pn,0x11) /* # frames 64 octets long */ +#define REG_RX_SIZE_65_TO_127(pn) CRA(0x4,pn,0x12) /* # frames 65-127 octets */ +#define REG_RX_SIZE_128_TO_255(pn) CRA(0x4,pn,0x13) /* # frames 128-255 */ +#define REG_RX_SIZE_256_TO_511(pn) CRA(0x4,pn,0x14) /* # frames 256-511 */ +#define REG_RX_SIZE_512_TO_1023(pn) CRA(0x4,pn,0x15) /* # frames 512-1023 */ +#define REG_RX_SIZE_1024_TO_1518(pn) CRA(0x4,pn,0x16) /* # frames 1024-1518 */ +#define REG_RX_SIZE_1519_TO_MAX(pn) CRA(0x4,pn,0x17) /* # frames 1519-max */ + +#define REG_TX_OUT_BYTES(pn) CRA(0x4,pn,0x18) /* # octets tx */ +#define REG_TX_PAUSE(pn) CRA(0x4,pn,0x19) /* # pause frames sent */ +#define REG_TX_OK_BYTES(pn) CRA(0x4,pn,0x1a) /* # octets tx OK */ +#define REG_TX_UNICAST(pn) CRA(0x4,pn,0x1b) /* # frames unicast */ +#define REG_TX_MULTICAST(pn) CRA(0x4,pn,0x1c) /* # frames multicast */ +#define REG_TX_BROADCAST(pn) CRA(0x4,pn,0x1d) /* # frames broadcast */ +#define REG_TX_MULTIPLE_COLL(pn) CRA(0x4,pn,0x1e) /* # frames tx after multiple collisions */ +#define REG_TX_LATE_COLL(pn) CRA(0x4,pn,0x1f) /* # late collisions detected */ +#define REG_TX_XCOLL(pn) CRA(0x4,pn,0x20) /* # frames lost, excessive collisions */ +#define REG_TX_DEFER(pn) CRA(0x4,pn,0x21) /* # frames deferred on first tx attempt */ +#define REG_TX_XDEFER(pn) CRA(0x4,pn,0x22) /* # frames excessively deferred */ +#define REG_TX_CSENSE(pn) CRA(0x4,pn,0x23) /* carrier sense errors at frame end */ +#define REG_TX_SIZE_64(pn) CRA(0x4,pn,0x24) /* # frames 64 octets long */ +#define REG_TX_SIZE_65_TO_127(pn) CRA(0x4,pn,0x25) /* # frames 65-127 octets */ +#define REG_TX_SIZE_128_TO_255(pn) CRA(0x4,pn,0x26) /* # frames 128-255 */ +#define REG_TX_SIZE_256_TO_511(pn) CRA(0x4,pn,0x27) /* # frames 256-511 */ +#define REG_TX_SIZE_512_TO_1023(pn) CRA(0x4,pn,0x28) /* # frames 512-1023 */ +#define REG_TX_SIZE_1024_TO_1518(pn) CRA(0x4,pn,0x29) /* # frames 1024-1518 */ +#define REG_TX_SIZE_1519_TO_MAX(pn) CRA(0x4,pn,0x2a) /* # frames 1519-max */ +#define REG_TX_SINGLE_COLL(pn) CRA(0x4,pn,0x2b) /* # frames tx after single collision */ +#define REG_TX_BACKOFF2(pn) CRA(0x4,pn,0x2c) /* # frames tx ok after 2 backoffs/collisions */ +#define REG_TX_BACKOFF3(pn) CRA(0x4,pn,0x2d) /* after 3 backoffs/collisions */ +#define REG_TX_BACKOFF4(pn) CRA(0x4,pn,0x2e) /* after 4 */ +#define REG_TX_BACKOFF5(pn) CRA(0x4,pn,0x2f) /* after 5 */ +#define REG_TX_BACKOFF6(pn) CRA(0x4,pn,0x30) /* after 6 */ +#define REG_TX_BACKOFF7(pn) CRA(0x4,pn,0x31) /* after 7 */ +#define REG_TX_BACKOFF8(pn) CRA(0x4,pn,0x32) /* after 8 */ +#define REG_TX_BACKOFF9(pn) CRA(0x4,pn,0x33) /* after 9 */ +#define REG_TX_BACKOFF10(pn) CRA(0x4,pn,0x34) /* after 10 */ +#define REG_TX_BACKOFF11(pn) CRA(0x4,pn,0x35) /* after 11 */ +#define REG_TX_BACKOFF12(pn) CRA(0x4,pn,0x36) /* after 12 */ +#define REG_TX_BACKOFF13(pn) CRA(0x4,pn,0x37) /* after 13 */ +#define REG_TX_BACKOFF14(pn) CRA(0x4,pn,0x38) /* after 14 */ +#define REG_TX_BACKOFF15(pn) CRA(0x4,pn,0x39) /* after 15 */ +#define REG_TX_UNDERRUN(pn) CRA(0x4,pn,0x3a) /* # frames dropped from underrun */ +#define REG_RX_XGMII_PROT_ERR CRA(0x4,0xa,0x3b) /* # protocol errors detected on XGMII interface */ +#define REG_RX_IPG_SHRINK(pn) CRA(0x4,pn,0x3c) /* # of IPG shrinks detected */ + +#define REG_STAT_STICKY1G(pn) CRA(0x4,pn,0x3e) /* tri-speed sticky bits */ +#define REG_STAT_STICKY10G CRA(0x4,0xa,0x3e) /* 10GbE sticky bits */ +#define REG_STAT_INIT(pn) CRA(0x4,pn,0x3f) /* Clear all statistics */ + +/* MII-Management Block registers */ +/* These are for MII-M interface 0, which is the bidirectional LVTTL one. If + * we hooked up to the one with separate directions, the middle 0x0 needs to + * change to 0x1. And the current errata states that MII-M 1 doesn't work. + */ + +#define REG_MIIM_STATUS CRA(0x3,0x0,0x00) /* MII-M Status */ +#define REG_MIIM_CMD CRA(0x3,0x0,0x01) /* MII-M Command */ +#define REG_MIIM_DATA CRA(0x3,0x0,0x02) /* MII-M Data */ +#define REG_MIIM_PRESCALE CRA(0x3,0x0,0x03) /* MII-M MDC Prescale */ + +#define REG_ING_FFILT_UM_EN CRA(0x2, 0, 0xd) +#define REG_ING_FFILT_BE_EN CRA(0x2, 0, 0x1d) +#define REG_ING_FFILT_VAL0 CRA(0x2, 0, 0x2d) +#define REG_ING_FFILT_VAL1 CRA(0x2, 0, 0x3d) +#define REG_ING_FFILT_MASK0 CRA(0x2, 0, 0x4d) +#define REG_ING_FFILT_MASK1 CRA(0x2, 0, 0x5d) +#define REG_ING_FFILT_MASK2 CRA(0x2, 0, 0x6d) +#define REG_ING_FFILT_ETYPE CRA(0x2, 0, 0x7d) + + +/* Whew. */ + +#endif |
