diff options
Diffstat (limited to 'drivers/char/ip2/i2lib.h')
| -rw-r--r-- | drivers/char/ip2/i2lib.h | 351 |
1 files changed, 0 insertions, 351 deletions
diff --git a/drivers/char/ip2/i2lib.h b/drivers/char/ip2/i2lib.h deleted file mode 100644 index e559e9bac06d..000000000000 --- a/drivers/char/ip2/i2lib.h +++ /dev/null @@ -1,351 +0,0 @@ -/******************************************************************************* -* -* (c) 1998 by Computone Corporation -* -******************************************************************************** -* -* -* PACKAGE: Linux tty Device Driver for IntelliPort II family of multiport -* serial I/O controllers. -* -* DESCRIPTION: Header file for high level library functions -* -*******************************************************************************/ -#ifndef I2LIB_H -#define I2LIB_H 1 -//------------------------------------------------------------------------------ -// I2LIB.H -// -// IntelliPort-II and IntelliPort-IIEX -// -// Defines, structure definitions, and external declarations for i2lib.c -//------------------------------------------------------------------------------ -//-------------------------------------- -// Mandatory Includes: -//-------------------------------------- -#include "ip2types.h" -#include "i2ellis.h" -#include "i2pack.h" -#include "i2cmd.h" -#include <linux/workqueue.h> - -//------------------------------------------------------------------------------ -// i2ChanStr -- Channel Structure: -// Used to track per-channel information for the library routines using standard -// loadware. Note also, a pointer to an array of these structures is patched -// into the i2eBordStr (see i2ellis.h) -//------------------------------------------------------------------------------ -// -// If we make some limits on the maximum block sizes, we can avoid dealing with -// buffer wrap. The wrapping of the buffer is based on where the start of the -// packet is. Then there is always room for the packet contiguously. -// -// Maximum total length of an outgoing data or in-line command block. The limit -// of 36 on data is quite arbitrary and based more on DOS memory limitations -// than the board interface. However, for commands, the maximum packet length is -// MAX_CMD_PACK_SIZE, because the field size for the count is only a few bits -// (see I2PACK.H) in such packets. For data packets, the count field size is not -// the limiting factor. As of this writing, MAX_OBUF_BLOCK < MAX_CMD_PACK_SIZE, -// but be careful if wanting to modify either. -// -#define MAX_OBUF_BLOCK 36 - -// Another note on maximum block sizes: we are buffering packets here. Data is -// put into the buffer (if there is room) regardless of the credits from the -// board. The board sends new credits whenever it has removed from his buffers a -// number of characters equal to 80% of total buffer size. (Of course, the total -// buffer size is what is reported when the very first set of flow control -// status packets are received from the board. Therefore, to be robust, you must -// always fill the board to at least 80% of the current credit limit, else you -// might not give it enough to trigger a new report. These conditions are -// obtained here so long as the maximum output block size is less than 20% the -// size of the board's output buffers. This is true at present by "coincidence" -// or "infernal knowledge": the board's output buffers are at least 700 bytes -// long (20% = 140 bytes, at least). The 80% figure is "official", so the safest -// strategy might be to trap the first flow control report and guarantee that -// the effective maxObufBlock is the minimum of MAX_OBUF_BLOCK and 20% of first -// reported buffer credit. -// -#define MAX_CBUF_BLOCK 6 // Maximum total length of a bypass command block - -#define IBUF_SIZE 512 // character capacity of input buffer per channel -#define OBUF_SIZE 1024// character capacity of output buffer per channel -#define CBUF_SIZE 10 // character capacity of output bypass buffer - -typedef struct _i2ChanStr -{ - // First, back-pointers so that given a pointer to this structure, you can - // determine the correct board and channel number to reference, (say, when - // issuing commands, etc. (Note, channel number is in infl.hd.i2sChannel.) - - int port_index; // Index of port in channel structure array attached - // to board structure. - PTTY pTTY; // Pointer to tty structure for port (OS specific) - USHORT validity; // Indicates whether the given channel has been - // initialized, really exists (or is a missing - // channel, e.g. channel 9 on an 8-port box.) - - i2eBordStrPtr pMyBord; // Back-pointer to this channel's board structure - - int wopen; // waiting fer carrier - - int throttled; // Set if upper layer can take no data - - int flags; // Defined in tty.h - - PWAITQ open_wait; // Pointer for OS sleep function. - PWAITQ close_wait; // Pointer for OS sleep function. - PWAITQ delta_msr_wait;// Pointer for OS sleep function. - PWAITQ dss_now_wait; // Pointer for OS sleep function. - - struct timer_list BookmarkTimer; // Used by i2DrainOutput - wait_queue_head_t pBookmarkWait; // Used by i2DrainOutput - - int BaudBase; - int BaudDivisor; - - USHORT ClosingDelay; - USHORT ClosingWaitTime; - - volatile - flowIn infl; // This structure is initialized as a completely - // formed flow-control command packet, and as such - // has the channel number, also the capacity and - // "as-of" data needed continuously. - - USHORT sinceLastFlow; // Counts the number of characters read from input - // buffers, since the last time flow control info - // was sent. - - USHORT whenSendFlow; // Determines when new flow control is to be sent to - // the board. Note unlike earlier manifestations of - // the driver, these packets can be sent from - // in-place. - - USHORT channelNeeds; // Bit map of important things which must be done - // for this channel. (See bits below ) - - volatile - flowStat outfl; // Same type of structure is used to hold current - // flow control information used to control our - // output. "asof" is kept updated as data is sent, - // and "room" never goes to zero. - - // The incoming ring buffer - // Unlike the outgoing buffers, this holds raw data, not packets. The two - // extra bytes are used to hold the byte-padding when there is room for an - // odd number of bytes before we must wrap. - // - UCHAR Ibuf[IBUF_SIZE + 2]; - volatile - USHORT Ibuf_stuff; // Stuffing index - volatile - USHORT Ibuf_strip; // Stripping index - - // The outgoing ring-buffer: Holds Data and command packets. N.B., even - // though these are in the channel structure, the channel is also written - // here, the easier to send it to the fifo when ready. HOWEVER, individual - // packets here are NOT padded to even length: the routines for writing - // blocks to the fifo will pad to even byte counts. - // - UCHAR Obuf[OBUF_SIZE+MAX_OBUF_BLOCK+4]; - volatile - USHORT Obuf_stuff; // Stuffing index - volatile - USHORT Obuf_strip; // Stripping index - int Obuf_char_count; - - // The outgoing bypass-command buffer. Unlike earlier manifestations, the - // flow control packets are sent directly from the structures. As above, the - // channel number is included in the packet, but they are NOT padded to even - // size. - // - UCHAR Cbuf[CBUF_SIZE+MAX_CBUF_BLOCK+2]; - volatile - USHORT Cbuf_stuff; // Stuffing index - volatile - USHORT Cbuf_strip; // Stripping index - - // The temporary buffer for the Linux tty driver PutChar entry. - // - UCHAR Pbuf[MAX_OBUF_BLOCK - sizeof (i2DataHeader)]; - volatile - USHORT Pbuf_stuff; // Stuffing index - - // The state of incoming data-set signals - // - USHORT dataSetIn; // Bit-mapped according to below. Also indicates - // whether a break has been detected since last - // inquiry. - - // The state of outcoming data-set signals (as far as we can tell!) - // - USHORT dataSetOut; // Bit-mapped according to below. - - // Most recent hot-key identifier detected - // - USHORT hotKeyIn; // Hot key as sent by the board, HOT_CLEAR indicates - // no hot key detected since last examined. - - // Counter of outstanding requests for bookmarks - // - short bookMarks; // Number of outstanding bookmark requests, (+ive - // whenever a bookmark request if queued up, -ive - // whenever a bookmark is received). - - // Misc options - // - USHORT channelOptions; // See below - - // To store various incoming special packets - // - debugStat channelStatus; - cntStat channelRcount; - cntStat channelTcount; - failStat channelFail; - - // To store the last values for line characteristics we sent to the board. - // - int speed; - - int flush_flags; - - void (*trace)(unsigned short,unsigned char,unsigned char,unsigned long,...); - - /* - * Kernel counters for the 4 input interrupts - */ - struct async_icount icount; - - /* - * Task queues for processing input packets from the board. - */ - struct work_struct tqueue_input; - struct work_struct tqueue_status; - struct work_struct tqueue_hangup; - - rwlock_t Ibuf_spinlock; - rwlock_t Obuf_spinlock; - rwlock_t Cbuf_spinlock; - rwlock_t Pbuf_spinlock; - -} i2ChanStr, *i2ChanStrPtr; - -//--------------------------------------------------- -// Manifests and bit-maps for elements in i2ChanStr -//--------------------------------------------------- -// -// flush flags -// -#define STARTFL_FLAG 1 -#define STOPFL_FLAG 2 - -// validity -// -#define CHANNEL_MAGIC_BITS 0xff00 -#define CHANNEL_MAGIC 0x5300 // (validity & CHANNEL_MAGIC_BITS) == - // CHANNEL_MAGIC --> structure good - -#define CHANNEL_SUPPORT 0x0001 // Indicates channel is supported, exists, - // and passed P.O.S.T. - -// channelNeeds -// -#define NEED_FLOW 1 // Indicates flow control has been queued -#define NEED_INLINE 2 // Indicates inline commands or data queued -#define NEED_BYPASS 4 // Indicates bypass commands queued -#define NEED_CREDIT 8 // Indicates would be sending except has not sufficient - // credit. The data is still in the channel structure, - // but the channel is not enqueued in the board - // structure again until there is a credit received from - // the board. - -// dataSetIn (Also the bits for i2GetStatus return value) -// -#define I2_DCD 1 -#define I2_CTS 2 -#define I2_DSR 4 -#define I2_RI 8 - -// dataSetOut (Also the bits for i2GetStatus return value) -// -#define I2_DTR 1 -#define I2_RTS 2 - -// i2GetStatus() can optionally clear these bits -// -#define I2_BRK 0x10 // A break was detected -#define I2_PAR 0x20 // A parity error was received -#define I2_FRA 0x40 // A framing error was received -#define I2_OVR 0x80 // An overrun error was received - -// i2GetStatus() automatically clears these bits */ -// -#define I2_DDCD 0x100 // DCD changed from its former value -#define I2_DCTS 0x200 // CTS changed from its former value -#define I2_DDSR 0x400 // DSR changed from its former value -#define I2_DRI 0x800 // RI changed from its former value - -// hotKeyIn -// -#define HOT_CLEAR 0x1322 // Indicates that no hot-key has been detected - -// channelOptions -// -#define CO_NBLOCK_WRITE 1 // Writes don't block waiting for buffer. (Default - // is, they do wait.) - -// fcmodes -// -#define I2_OUTFLOW_CTS 0x0001 -#define I2_INFLOW_RTS 0x0002 -#define I2_INFLOW_DSR 0x0004 -#define I2_INFLOW_DTR 0x0008 -#define I2_OUTFLOW_DSR 0x0010 -#define I2_OUTFLOW_DTR 0x0020 -#define I2_OUTFLOW_XON 0x0040 -#define I2_OUTFLOW_XANY 0x0080 -#define I2_INFLOW_XON 0x0100 - -#define I2_CRTSCTS (I2_OUTFLOW_CTS|I2_INFLOW_RTS) -#define I2_IXANY_MODE (I2_OUTFLOW_XON|I2_OUTFLOW_XANY) - -//------------------------------------------- -// Macros used from user level like functions -//------------------------------------------- - -// Macros to set and clear channel options -// -#define i2SetOption(pCh, option) pCh->channelOptions |= option -#define i2ClrOption(pCh, option) pCh->channelOptions &= ~option - -// Macro to set fatal-error trap -// -#define i2SetFatalTrap(pB, routine) pB->i2eFatalTrap = routine - -//-------------------------------------------- -// Declarations and prototypes for i2lib.c -//-------------------------------------------- -// -static int i2InitChannels(i2eBordStrPtr, int, i2ChanStrPtr); -static int i2QueueCommands(int, i2ChanStrPtr, int, int, cmdSyntaxPtr,...); -static int i2GetStatus(i2ChanStrPtr, int); -static int i2Input(i2ChanStrPtr); -static int i2InputFlush(i2ChanStrPtr); -static int i2Output(i2ChanStrPtr, const char *, int); -static int i2OutputFree(i2ChanStrPtr); -static int i2ServiceBoard(i2eBordStrPtr); -static void i2DrainOutput(i2ChanStrPtr, int); - -#ifdef IP2DEBUG_TRACE -void ip2trace(unsigned short,unsigned char,unsigned char,unsigned long,...); -#else -#define ip2trace(a,b,c,d...) do {} while (0) -#endif - -// Argument to i2QueueCommands -// -#define C_IN_LINE 1 -#define C_BYPASS 0 - -#endif // I2LIB_H |
