diff options
Diffstat (limited to 'arch/powerpc/platforms')
| -rw-r--r-- | arch/powerpc/platforms/chrp/setup.c | 12 | ||||
| -rw-r--r-- | arch/powerpc/platforms/maple/setup.c | 17 | ||||
| -rw-r--r-- | arch/powerpc/platforms/powermac/bootx_init.c | 35 | ||||
| -rw-r--r-- | arch/powerpc/platforms/powermac/cpufreq_64.c | 78 | ||||
| -rw-r--r-- | arch/powerpc/platforms/pseries/setup.c | 6 |
5 files changed, 98 insertions, 50 deletions
diff --git a/arch/powerpc/platforms/chrp/setup.c b/arch/powerpc/platforms/chrp/setup.c index 538e337d63e2..9c08ff322290 100644 --- a/arch/powerpc/platforms/chrp/setup.c +++ b/arch/powerpc/platforms/chrp/setup.c @@ -291,10 +291,6 @@ void __init chrp_setup_arch(void) pci_create_OF_bus_map(); -#ifdef CONFIG_SMP - smp_ops = &chrp_smp_ops; -#endif /* CONFIG_SMP */ - /* * Print the banner, then scroll down so boot progress * can be printed. -- Cort @@ -479,6 +475,14 @@ void __init chrp_init_IRQ(void) chrp_find_openpic(); chrp_find_8259(); +#ifdef CONFIG_SMP + /* Pegasos has no MPIC, those ops would make it crash. It might be an + * option to move setting them to after we probe the PIC though + */ + if (chrp_mpic != NULL) + smp_ops = &chrp_smp_ops; +#endif /* CONFIG_SMP */ + if (_chrp_type == _CHRP_Pegasos) ppc_md.get_irq = i8259_irq; diff --git a/arch/powerpc/platforms/maple/setup.c b/arch/powerpc/platforms/maple/setup.c index cb528c9de4c3..57567dfb9819 100644 --- a/arch/powerpc/platforms/maple/setup.c +++ b/arch/powerpc/platforms/maple/setup.c @@ -221,10 +221,17 @@ static void __init maple_init_IRQ(void) * in Maple device-tree where the type of the controller is * open-pic and not interrupt-controller */ - for_each_node_by_type(np, "open-pic") { - mpic_node = np; - break; - } + + for_each_node_by_type(np, "interrupt-controller") + if (device_is_compatible(np, "open-pic")) { + mpic_node = np; + break; + } + if (mpic_node == NULL) + for_each_node_by_type(np, "open-pic") { + mpic_node = np; + break; + } if (mpic_node == NULL) { printk(KERN_ERR "Failed to locate the MPIC interrupt controller\n"); @@ -252,6 +259,8 @@ static void __init maple_init_IRQ(void) /* XXX Maple specific bits */ flags |= MPIC_BROKEN_U3 | MPIC_WANTS_RESET; + /* All U3/U4 are big-endian, older SLOF firmware doesn't encode this */ + flags |= MPIC_BIG_ENDIAN; /* Setup the openpic driver. More device-tree junks, we hard code no * ISUs for now. I'll have to revisit some stuffs with the folks doing diff --git a/arch/powerpc/platforms/powermac/bootx_init.c b/arch/powerpc/platforms/powermac/bootx_init.c index 871b002c9f90..6a026c733f6a 100644 --- a/arch/powerpc/platforms/powermac/bootx_init.c +++ b/arch/powerpc/platforms/powermac/bootx_init.c @@ -181,13 +181,18 @@ static void __init bootx_add_chosen_props(unsigned long base, } static void __init bootx_add_display_props(unsigned long base, - unsigned long *mem_end) + unsigned long *mem_end, + int has_real_node) { boot_infos_t *bi = bootx_info; u32 tmp; - bootx_dt_add_prop("linux,boot-display", NULL, 0, mem_end); - bootx_dt_add_prop("linux,opened", NULL, 0, mem_end); + if (has_real_node) { + bootx_dt_add_prop("linux,boot-display", NULL, 0, mem_end); + bootx_dt_add_prop("linux,opened", NULL, 0, mem_end); + } else + bootx_dt_add_prop("linux,bootx-noscreen", NULL, 0, mem_end); + tmp = bi->dispDeviceDepth; bootx_dt_add_prop("linux,bootx-depth", &tmp, 4, mem_end); tmp = bi->dispDeviceRect[2] - bi->dispDeviceRect[0]; @@ -241,11 +246,6 @@ static void __init bootx_scan_dt_build_strings(unsigned long base, DBG(" detected display ! adding properties names !\n"); bootx_dt_add_string("linux,boot-display", mem_end); bootx_dt_add_string("linux,opened", mem_end); - bootx_dt_add_string("linux,bootx-depth", mem_end); - bootx_dt_add_string("linux,bootx-width", mem_end); - bootx_dt_add_string("linux,bootx-height", mem_end); - bootx_dt_add_string("linux,bootx-linebytes", mem_end); - bootx_dt_add_string("linux,bootx-addr", mem_end); strncpy(bootx_disp_path, namep, 255); } @@ -329,10 +329,13 @@ static void __init bootx_scan_dt_build_struct(unsigned long base, ppp = &pp->next; } - if (node == bootx_node_chosen) + if (node == bootx_node_chosen) { bootx_add_chosen_props(base, mem_end); - if (node == bootx_info->dispDeviceRegEntryOffset) - bootx_add_display_props(base, mem_end); + if (bootx_info->dispDeviceRegEntryOffset == 0) + bootx_add_display_props(base, mem_end, 0); + } + else if (node == bootx_info->dispDeviceRegEntryOffset) + bootx_add_display_props(base, mem_end, 1); /* do all our children */ cpp = &np->child; @@ -374,6 +377,14 @@ static unsigned long __init bootx_flatten_dt(unsigned long start) mem_end += 4; bootx_dt_strend = mem_end; bootx_scan_dt_build_strings(base, 4, &mem_end); + /* Add some strings */ + bootx_dt_add_string("linux,bootx-noscreen", &mem_end); + bootx_dt_add_string("linux,bootx-depth", &mem_end); + bootx_dt_add_string("linux,bootx-width", &mem_end); + bootx_dt_add_string("linux,bootx-height", &mem_end); + bootx_dt_add_string("linux,bootx-linebytes", &mem_end); + bootx_dt_add_string("linux,bootx-addr", &mem_end); + /* Wrap up strings */ hdr->off_dt_strings = bootx_dt_strbase - mem_start; hdr->dt_strings_size = bootx_dt_strend - bootx_dt_strbase; @@ -471,6 +482,7 @@ void __init bootx_init(unsigned long r3, unsigned long r4) if (bi->dispDeviceDepth == 16) bi->dispDeviceDepth = 15; + #ifdef CONFIG_BOOTX_TEXT ptr = (unsigned long)bi->logicalDisplayBase; ptr += bi->dispDeviceRect[1] * bi->dispDeviceRowBytes; @@ -508,6 +520,7 @@ void __init bootx_init(unsigned long r3, unsigned long r4) #ifdef CONFIG_BOOTX_TEXT btext_welcome(bi); #endif + /* New BootX enters kernel with MMU off, i/os are not allowed * here. This hack will have been done by the boostrap anyway. */ diff --git a/arch/powerpc/platforms/powermac/cpufreq_64.c b/arch/powerpc/platforms/powermac/cpufreq_64.c index f08a14516139..7b1156ea5341 100644 --- a/arch/powerpc/platforms/powermac/cpufreq_64.c +++ b/arch/powerpc/platforms/powermac/cpufreq_64.c @@ -10,6 +10,8 @@ * that is iMac G5 and latest single CPU desktop. */ +#undef DEBUG + #include <linux/module.h> #include <linux/types.h> #include <linux/errno.h> @@ -30,13 +32,7 @@ #include <asm/smu.h> #include <asm/pmac_pfunc.h> -#undef DEBUG - -#ifdef DEBUG -#define DBG(fmt...) printk(fmt) -#else -#define DBG(fmt...) -#endif +#define DBG(fmt...) pr_debug(fmt) /* see 970FX user manual */ @@ -82,8 +78,6 @@ static struct freq_attr* g5_cpu_freqs_attr[] = { /* Power mode data is an array of the 32 bits PCR values to use for * the various frequencies, retrieved from the device-tree */ -static u32 *g5_pmode_data; -static int g5_pmode_max; static int g5_pmode_cur; static void (*g5_switch_volt)(int speed_mode); @@ -93,6 +87,11 @@ static int (*g5_query_freq)(void); static DEFINE_MUTEX(g5_switch_mutex); +#ifdef CONFIG_PMAC_SMU + +static u32 *g5_pmode_data; +static int g5_pmode_max; + static struct smu_sdbp_fvt *g5_fvt_table; /* table of op. points */ static int g5_fvt_count; /* number of op. points */ static int g5_fvt_cur; /* current op. point */ @@ -210,6 +209,16 @@ static int g5_scom_query_freq(void) } /* + * Fake voltage switching for platforms with missing support + */ + +static void g5_dummy_switch_volt(int speed_mode) +{ +} + +#endif /* CONFIG_PMAC_SMU */ + +/* * Platform function based voltage switching for PowerMac7,2 & 7,3 */ @@ -248,6 +257,9 @@ static int g5_pfunc_switch_freq(int speed_mode) struct pmf_args args; u32 done = 0; unsigned long timeout; + int rc; + + DBG("g5_pfunc_switch_freq(%d)\n", speed_mode); /* If frequency is going up, first ramp up the voltage */ if (speed_mode < g5_pmode_cur) @@ -255,9 +267,12 @@ static int g5_pfunc_switch_freq(int speed_mode) /* Do it */ if (speed_mode == CPUFREQ_HIGH) - pmf_call_one(pfunc_cpu_setfreq_high, NULL); + rc = pmf_call_one(pfunc_cpu_setfreq_high, NULL); else - pmf_call_one(pfunc_cpu_setfreq_low, NULL); + rc = pmf_call_one(pfunc_cpu_setfreq_low, NULL); + + if (rc) + printk(KERN_WARNING "cpufreq: pfunc switch error %d\n", rc); /* It's an irq GPIO so we should be able to just block here, * I'll do that later after I've properly tested the IRQ code for @@ -296,13 +311,6 @@ static int g5_pfunc_query_freq(void) return val ? CPUFREQ_HIGH : CPUFREQ_LOW; } -/* - * Fake voltage switching for platforms with missing support - */ - -static void g5_dummy_switch_volt(int speed_mode) -{ -} /* * Common interface to the cpufreq core @@ -375,6 +383,8 @@ static struct cpufreq_driver g5_cpufreq_driver = { }; +#ifdef CONFIG_PMAC_SMU + static int __init g5_neo2_cpufreq_init(struct device_node *cpus) { struct device_node *cpunode; @@ -525,6 +535,9 @@ static int __init g5_neo2_cpufreq_init(struct device_node *cpus) return rc; } +#endif /* CONFIG_PMAC_SMU */ + + static int __init g5_pm72_cpufreq_init(struct device_node *cpus) { struct device_node *cpuid = NULL, *hwclock = NULL, *cpunode = NULL; @@ -533,6 +546,9 @@ static int __init g5_pm72_cpufreq_init(struct device_node *cpus) u64 max_freq, min_freq, ih, il; int has_volt = 1, rc = 0; + DBG("cpufreq: Initializing for PowerMac7,2, PowerMac7,3 and" + " RackMac3,1...\n"); + /* Get first CPU node */ for (cpunode = NULL; (cpunode = of_get_next_child(cpus, cpunode)) != NULL;) { @@ -636,6 +652,15 @@ static int __init g5_pm72_cpufreq_init(struct device_node *cpus) */ ih = *((u32 *)(eeprom + 0x10)); il = *((u32 *)(eeprom + 0x20)); + + /* Check for machines with no useful settings */ + if (il == ih) { + printk(KERN_WARNING "cpufreq: No low frequency mode available" + " on this model !\n"); + rc = -ENODEV; + goto bail; + } + min_freq = 0; if (ih != 0 && il != 0) min_freq = (max_freq * il) / ih; @@ -643,7 +668,7 @@ static int __init g5_pm72_cpufreq_init(struct device_node *cpus) /* Sanity check */ if (min_freq >= max_freq || min_freq < 1000) { printk(KERN_ERR "cpufreq: Can't calculate low frequency !\n"); - rc = -ENODEV; + rc = -ENXIO; goto bail; } g5_cpu_freqs[0].frequency = max_freq; @@ -690,16 +715,10 @@ static int __init g5_pm72_cpufreq_init(struct device_node *cpus) return rc; } -static int __init g5_rm31_cpufreq_init(struct device_node *cpus) -{ - /* NYI */ - return 0; -} - static int __init g5_cpufreq_init(void) { struct device_node *cpus; - int rc; + int rc = 0; cpus = of_find_node_by_path("/cpus"); if (cpus == NULL) { @@ -708,12 +727,13 @@ static int __init g5_cpufreq_init(void) } if (machine_is_compatible("PowerMac7,2") || - machine_is_compatible("PowerMac7,3")) + machine_is_compatible("PowerMac7,3") || + machine_is_compatible("RackMac3,1")) rc = g5_pm72_cpufreq_init(cpus); - else if (machine_is_compatible("RackMac3,1")) - rc = g5_rm31_cpufreq_init(cpus); +#ifdef CONFIG_PMAC_SMU else rc = g5_neo2_cpufreq_init(cpus); +#endif /* CONFIG_PMAC_SMU */ of_node_put(cpus); return rc; diff --git a/arch/powerpc/platforms/pseries/setup.c b/arch/powerpc/platforms/pseries/setup.c index 54a52437265c..71c634e0b87c 100644 --- a/arch/powerpc/platforms/pseries/setup.c +++ b/arch/powerpc/platforms/pseries/setup.c @@ -501,7 +501,8 @@ static void pseries_dedicated_idle_sleep(void) } /* - * Cede if the other thread is not idle, so that it can + * If not SMT, cede processor. If CPU is running SMT + * cede if the other thread is not idle, so that it can * go single-threaded. If the other thread is idle, * we ask the hypervisor if it has pending work it * wants to do and cede if it does. Otherwise we keep @@ -514,7 +515,8 @@ static void pseries_dedicated_idle_sleep(void) * very low priority. The cede enables interrupts, which * doesn't matter here. */ - if (!lppaca[cpu ^ 1].idle || poll_pending() == H_PENDING) + if (!cpu_has_feature(CPU_FTR_SMT) || !lppaca[cpu ^ 1].idle + || poll_pending() == H_PENDING) cede_processor(); out: |
