diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-usb | 20 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/phy/brcm,cygnus-pcie-phy.txt | 47 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt | 68 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/phy/samsung-phy.txt | 3 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt | 27 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/usb/dwc3.txt | 5 | ||||
| -rw-r--r-- | Documentation/usb/authorization.txt | 31 |
7 files changed, 195 insertions, 6 deletions
diff --git a/Documentation/ABI/testing/sysfs-bus-usb b/Documentation/ABI/testing/sysfs-bus-usb index 864637f25bee..3a4abfc44f5e 100644 --- a/Documentation/ABI/testing/sysfs-bus-usb +++ b/Documentation/ABI/testing/sysfs-bus-usb @@ -1,3 +1,23 @@ +What: /sys/bus/usb/devices/INTERFACE/authorized +Date: August 2015 +Description: + This allows to authorize (1) or deauthorize (0) + individual interfaces instead a whole device + in contrast to the device authorization. + If a deauthorized interface will be authorized + so the driver probing must be triggered manually + by writing INTERFACE to /sys/bus/usb/drivers_probe + This allows to avoid side-effects with drivers + that need multiple interfaces. + A deauthorized interface cannot be probed or claimed. + +What: /sys/bus/usb/devices/usbX/interface_authorized_default +Date: August 2015 +Description: + This is used as value that determines if interfaces + would be authorized by default. + The value can be 1 or 0. It's by default 1. + What: /sys/bus/usb/device/.../authorized Date: July 2008 KernelVersion: 2.6.26 diff --git a/Documentation/devicetree/bindings/phy/brcm,cygnus-pcie-phy.txt b/Documentation/devicetree/bindings/phy/brcm,cygnus-pcie-phy.txt new file mode 100644 index 000000000000..761c4bc24a9b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,cygnus-pcie-phy.txt @@ -0,0 +1,47 @@ +Broadcom Cygnus PCIe PHY + +Required properties: +- compatible: must be "brcm,cygnus-pcie-phy" +- reg: base address and length of the PCIe PHY block +- #address-cells: must be 1 +- #size-cells: must be 0 + +Each PCIe PHY should be represented by a child node + +Required properties For the child node: +- reg: the PHY ID +0 - PCIe RC 0 +1 - PCIe RC 1 +- #phy-cells: must be 0 + +Example: + pcie_phy: phy@0301d0a0 { + compatible = "brcm,cygnus-pcie-phy"; + reg = <0x0301d0a0 0x14>; + + pcie0_phy: phy@0 { + reg = <0>; + #phy-cells = <0>; + }; + + pcie1_phy: phy@1 { + reg = <1>; + #phy-cells = <0>; + }; + }; + + /* users of the PCIe phy */ + + pcie0: pcie@18012000 { + ... + ... + phys = <&pcie0_phy>; + phy-names = "pcie-phy"; + }; + + pcie1: pcie@18013000 { + ... + ... + phys = <pcie1_phy>; + phy-names = "pcie-phy"; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt new file mode 100644 index 000000000000..00100cf3e037 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-mt65xx-usb.txt @@ -0,0 +1,68 @@ +mt65xx USB3.0 PHY binding +-------------------------- + +This binding describes a usb3.0 phy for mt65xx platforms of Medaitek SoC. + +Required properties (controller (parent) node): + - compatible : should be "mediatek,mt8173-u3phy" + - reg : offset and length of register for phy, exclude port's + register. + - clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names : must contain + "u3phya_ref": for reference clock of usb3.0 analog phy. + +Required nodes : a sub-node is required for each port the controller + provides. Address range information including the usual + 'reg' property is used inside these nodes to describe + the controller's topology. + +Required properties (port (child) node): +- reg : address and length of the register set for the port. +- #phy-cells : should be 1 (See second example) + cell after port phandle is phy type from: + - PHY_TYPE_USB2 + - PHY_TYPE_USB3 + +Example: + +u3phy: usb-phy@11290000 { + compatible = "mediatek,mt8173-u3phy"; + reg = <0 0x11290000 0 0x800>; + clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>; + clock-names = "u3phya_ref"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + status = "okay"; + + phy_port0: port@11290800 { + reg = <0 0x11290800 0 0x800>; + #phy-cells = <1>; + status = "okay"; + }; + + phy_port1: port@11291000 { + reg = <0 0x11291000 0 0x800>; + #phy-cells = <1>; + status = "okay"; + }; +}; + +Specifying phy control of devices +--------------------------------- + +Device nodes should specify the configuration required in their "phys" +property, containing a phandle to the phy port node and a device type; +phy-names for each port are optional. + +Example: + +#include <dt-bindings/phy/phy.h> + +usb30: usb@11270000 { + ... + phys = <&phy_port0 PHY_TYPE_USB3>; + phy-names = "usb3-0"; + ... +}; diff --git a/Documentation/devicetree/bindings/phy/samsung-phy.txt b/Documentation/devicetree/bindings/phy/samsung-phy.txt index 60c6f2a633e0..0289d3b07853 100644 --- a/Documentation/devicetree/bindings/phy/samsung-phy.txt +++ b/Documentation/devicetree/bindings/phy/samsung-phy.txt @@ -44,6 +44,9 @@ Required properties: - the "ref" clock is used to get the rate of the clock provided to the PHY module +Optional properties: +- vbus-supply: power-supply phandle for vbus power source + The first phandle argument in the PHY specifier identifies the PHY, its meaning is compatible dependent. For the currently supported SoCs (Exynos 4210 and Exynos 4212) it is as follows: diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index a057b75ba4b5..781296bfbe4f 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -27,10 +27,6 @@ Optional properties: - vbus-supply: reference to the VBUS regulator - maximum-speed: limit the maximum connection speed to "full-speed". - tpl-support: TPL (Targeted Peripheral List) feature for targeted hosts -- fsl,usbmisc: (FSL only) phandler of non-core register device, with one - argument that indicate usb controller index -- disable-over-current: (FSL only) disable over current detect -- external-vbus-divider: (FSL only) enables off-chip resistor divider for Vbus - itc-setting: interrupt threshold control register control, the setting should be aligned with ITC bits at register USBCMD. - ahb-burst-config: it is vendor dependent, the required value should be @@ -41,11 +37,28 @@ Optional properties: - tx-burst-size-dword: it is vendor dependent, the tx burst size in dword (4 bytes), This register represents the maximum length of a the burst in 32-bit words while moving data from system memory to the USB - bus, changing this value takes effect only the SBUSCFG.AHBBRST is 0. + bus, the value of this property will only take effect if property + "ahb-burst-config" is set to 0, if this property is missing the reset + default of the hardware implementation will be used. - rx-burst-size-dword: it is vendor dependent, the rx burst size in dword (4 bytes), This register represents the maximum length of a the burst in 32-bit words while moving data from the USB bus to system memory, - changing this value takes effect only the SBUSCFG.AHBBRST is 0. + the value of this property will only take effect if property + "ahb-burst-config" is set to 0, if this property is missing the reset + default of the hardware implementation will be used. +- extcon: phandles to external connector devices. First phandle should point to + external connector, which provide "USB" cable events, the second should point + to external connector device, which provide "USB-HOST" cable events. If one + of the external connector devices is not required, empty <0> phandle should + be specified. +- phy-clkgate-delay-us: the delay time (us) between putting the PHY into + low power mode and gating the PHY clock. + +i.mx specific properties +- fsl,usbmisc: phandler of non-core register device, with one + argument that indicate usb controller index +- disable-over-current: disable over current detect +- external-vbus-divider: enables off-chip resistor divider for Vbus Example: @@ -62,4 +75,6 @@ Example: ahb-burst-config = <0x0>; tx-burst-size-dword = <0x10>; /* 64 bytes */ rx-burst-size-dword = <0x10>; + extcon = <0>, <&usb_id>; + phy-clkgate-delay-us = <400>; }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt index 0815eac5b185..9ff48e0defb4 100644 --- a/Documentation/devicetree/bindings/usb/dwc3.txt +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -35,11 +35,16 @@ Optional properties: LTSSM during USB3 Compliance mode. - snps,dis_u3_susphy_quirk: when set core will disable USB3 suspend phy. - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy. + - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG, + disabling the suspend signal to the PHY. - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal utmi_l1_suspend_n, false when asserts utmi_sleep_n - snps,hird-threshold: HIRD threshold - snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3. + - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ + register for post-silicon frame length adjustment when the + fladj_30mhz_sdbnd signal is invalid or incorrect. This is usually a subnode to DWC3 glue to which it is connected. diff --git a/Documentation/usb/authorization.txt b/Documentation/usb/authorization.txt index c069b6884c77..c7e985f05d8f 100644 --- a/Documentation/usb/authorization.txt +++ b/Documentation/usb/authorization.txt @@ -90,3 +90,34 @@ etc, but you get the idea. Anybody with access to a device gadget kit can fake descriptors and device info. Don't trust that. You are welcome. + +Interface authorization +----------------------- +There is a similar approach to allow or deny specific USB interfaces. +That allows to block only a subset of an USB device. + +Authorize an interface: +$ echo 1 > /sys/bus/usb/devices/INTERFACE/authorized + +Deauthorize an interface: +$ echo 0 > /sys/bus/usb/devices/INTERFACE/authorized + +The default value for new interfaces +on a particular USB bus can be changed, too. + +Allow interfaces per default: +$ echo 1 > /sys/bus/usb/devices/usbX/interface_authorized_default + +Deny interfaces per default: +$ echo 0 > /sys/bus/usb/devices/usbX/interface_authorized_default + +Per default the interface_authorized_default bit is 1. +So all interfaces would authorized per default. + +Note: +If a deauthorized interface will be authorized so the driver probing must +be triggered manually by writing INTERFACE to /sys/bus/usb/drivers_probe + +For drivers that need multiple interfaces all needed interfaces should be +authroized first. After that the drivers should be probed. +This avoids side effects. |
