diff options
Diffstat (limited to 'Documentation/devicetree/bindings')
82 files changed, 2273 insertions, 111 deletions
diff --git a/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt b/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt new file mode 100644 index 000000000000..885f93d14ef9 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/altera/socfpga-eccmgr.txt @@ -0,0 +1,49 @@ +Altera SoCFPGA ECC Manager +This driver uses the EDAC framework to implement the SOCFPGA ECC Manager. +The ECC Manager counts and corrects single bit errors and counts/handles +double bit errors which are uncorrectable. + +Required Properties: +- compatible : Should be "altr,socfpga-ecc-manager" +- #address-cells: must be 1 +- #size-cells: must be 1 +- ranges : standard definition, should translate from local addresses + +Subcomponents: + +L2 Cache ECC +Required Properties: +- compatible : Should be "altr,socfpga-l2-ecc" +- reg : Address and size for ECC error interrupt clear registers. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt. Note the rising edge type. + +On Chip RAM ECC +Required Properties: +- compatible : Should be "altr,socfpga-ocram-ecc" +- reg : Address and size for ECC error interrupt clear registers. +- iram : phandle to On-Chip RAM definition. +- interrupts : Should be single bit error interrupt, then double bit error + interrupt. Note the rising edge type. + +Example: + + eccmgr: eccmgr@ffd08140 { + compatible = "altr,socfpga-ecc-manager"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + l2-ecc@ffd08140 { + compatible = "altr,socfpga-l2-ecc"; + reg = <0xffd08140 0x4>; + interrupts = <0 36 1>, <0 37 1>; + }; + + ocram-ecc@ffd08144 { + compatible = "altr,socfpga-ocram-ecc"; + reg = <0xffd08144 0x4>; + iram = <&ocram>; + interrupts = <0 178 1>, <0 179 1>; + }; + }; diff --git a/Documentation/devicetree/bindings/arm/fw-cfg.txt b/Documentation/devicetree/bindings/arm/fw-cfg.txt index 953fb640d9c4..fd54e1db2156 100644 --- a/Documentation/devicetree/bindings/arm/fw-cfg.txt +++ b/Documentation/devicetree/bindings/arm/fw-cfg.txt @@ -11,43 +11,9 @@ QEMU exposes the control and data register to ARM guests as memory mapped registers; their location is communicated to the guest's UEFI firmware in the DTB that QEMU places at the bottom of the guest's DRAM. -The guest writes a selector value (a key) to the selector register, and then -can read the corresponding data (produced by QEMU) via the data register. If -the selected entry is writable, the guest can rewrite it through the data -register. +The authoritative guest-side hardware interface documentation to the fw_cfg +device can be found in "docs/specs/fw_cfg.txt" in the QEMU source tree. -The selector register takes keys in big endian byte order. - -The data register allows accesses with 8, 16, 32 and 64-bit width (only at -offset 0 of the register). Accesses larger than a byte are interpreted as -arrays, bundled together only for better performance. The bytes constituting -such a word, in increasing address order, correspond to the bytes that would -have been transferred by byte-wide accesses in chronological order. - -The interface allows guest firmware to download various parameters and blobs -that affect how the firmware works and what tables it installs for the guest -OS. For example, boot order of devices, ACPI tables, SMBIOS tables, kernel and -initrd images for direct kernel booting, virtual machine UUID, SMP information, -virtual NUMA topology, and so on. - -The authoritative registry of the valid selector values and their meanings is -the QEMU source code; the structure of the data blobs corresponding to the -individual key values is also defined in the QEMU source code. - -The presence of the registers can be verified by selecting the "signature" blob -with key 0x0000, and reading four bytes from the data register. The returned -signature is "QEMU". - -The outermost protocol (involving the write / read sequences of the control and -data registers) is expected to be versioned, and/or described by feature bits. -The interface revision / feature bitmap can be retrieved with key 0x0001. The -blob to be read from the data register has size 4, and it is to be interpreted -as a uint32_t value in little endian byte order. The current value -(corresponding to the above outer protocol) is zero. - -The guest kernel is not expected to use these registers (although it is -certainly allowed to); the device tree bindings are documented here because -this is where device tree bindings reside in general. Required properties: diff --git a/Documentation/devicetree/bindings/dma/arm-pl330.txt b/Documentation/devicetree/bindings/dma/arm-pl330.txt index 267565894db9..db7e2260f9c5 100644 --- a/Documentation/devicetree/bindings/dma/arm-pl330.txt +++ b/Documentation/devicetree/bindings/dma/arm-pl330.txt @@ -15,6 +15,7 @@ Optional properties: cells in the dmas property of client device. - dma-channels: contains the total number of DMA channels supported by the DMAC - dma-requests: contains the total number of DMA requests supported by the DMAC + - arm,pl330-broken-no-flushp: quirk for avoiding to execute DMAFLUSHP Example: diff --git a/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt b/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt new file mode 100644 index 000000000000..fd5618bd8fbc --- /dev/null +++ b/Documentation/devicetree/bindings/dma/qcom_hidma_mgmt.txt @@ -0,0 +1,89 @@ +Qualcomm Technologies HIDMA Management interface + +Qualcomm Technologies HIDMA is a high speed DMA device. It only supports +memcpy and memset capabilities. It has been designed for virtualized +environments. + +Each HIDMA HW instance consists of multiple DMA channels. These channels +share the same bandwidth. The bandwidth utilization can be parititioned +among channels based on the priority and weight assignments. + +There are only two priority levels and 15 weigh assignments possible. + +Other parameters here determine how much of the system bus this HIDMA +instance can use like maximum read/write request and and number of bytes to +read/write in a single burst. + +Main node required properties: +- compatible: "qcom,hidma-mgmt-1.0"; +- reg: Address range for DMA device +- dma-channels: Number of channels supported by this DMA controller. +- max-write-burst-bytes: Maximum write burst in bytes that HIDMA can + occupy the bus for in a single transaction. A memcpy requested is + fragmented to multiples of this amount. This parameter is used while + writing into destination memory. Setting this value incorrectly can + starve other peripherals in the system. +- max-read-burst-bytes: Maximum read burst in bytes that HIDMA can + occupy the bus for in a single transaction. A memcpy request is + fragmented to multiples of this amount. This parameter is used while + reading the source memory. Setting this value incorrectly can starve + other peripherals in the system. +- max-write-transactions: This value is how many times a write burst is + applied back to back while writing to the destination before yielding + the bus. +- max-read-transactions: This value is how many times a read burst is + applied back to back while reading the source before yielding the bus. +- channel-reset-timeout-cycles: Channel reset timeout in cycles for this SOC. + Once a reset is applied to the HW, HW starts a timer for reset operation + to confirm. If reset is not completed within this time, HW reports reset + failure. + +Sub-nodes: + +HIDMA has one or more DMA channels that are used to move data from one +memory location to another. + +When the OS is not in control of the management interface (i.e. it's a guest), +the channel nodes appear on their own, not under a management node. + +Required properties: +- compatible: must contain "qcom,hidma-1.0" +- reg: Addresses for the transfer and event channel +- interrupts: Should contain the event interrupt +- desc-count: Number of asynchronous requests this channel can handle +- iommus: required a iommu node + +Example: + +Hypervisor OS configuration: + + hidma-mgmt@f9984000 = { + compatible = "qcom,hidma-mgmt-1.0"; + reg = <0xf9984000 0x15000>; + dma-channels = <6>; + max-write-burst-bytes = <1024>; + max-read-burst-bytes = <1024>; + max-write-transactions = <31>; + max-read-transactions = <31>; + channel-reset-timeout-cycles = <0x500>; + + hidma_24: dma-controller@0x5c050000 { + compatible = "qcom,hidma-1.0"; + reg = <0 0x5c050000 0x0 0x1000>, + <0 0x5c0b0000 0x0 0x1000>; + interrupts = <0 389 0>; + desc-count = <10>; + iommus = <&system_mmu>; + }; + }; + +Guest OS configuration: + + hidma_24: dma-controller@0x5c050000 { + compatible = "qcom,hidma-1.0"; + reg = <0 0x5c050000 0x0 0x1000>, + <0 0x5c0b0000 0x0 0x1000>; + interrupts = <0 389 0>; + desc-count = <10>; + iommus = <&system_mmu>; + }; diff --git a/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt b/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt index 78e2a31c58d0..1006b0489464 100644 --- a/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt +++ b/Documentation/devicetree/bindings/edac/apm-xgene-edac.txt @@ -16,6 +16,10 @@ Required properties: - regmap-mcba : Regmap of the MCB-A (memory bridge) resource. - regmap-mcbb : Regmap of the MCB-B (memory bridge) resource. - regmap-efuse : Regmap of the PMD efuse resource. +- regmap-rb : Regmap of the register bus resource. This property + is optional only for compatibility. If the RB + error conditions are not cleared, it will + continuously generate interrupt. - reg : First resource shall be the CPU bus (PCP) resource. - interrupts : Interrupt-specifier for MCU, PMD, L3, or SoC error IRQ(s). @@ -64,6 +68,11 @@ Example: reg = <0x0 0x1054a000 0x0 0x20>; }; + rb: rb@7e000000 { + compatible = "apm,xgene-rb", "syscon"; + reg = <0x0 0x7e000000 0x0 0x10>; + }; + edac@78800000 { compatible = "apm,xgene-edac"; #address-cells = <2>; @@ -73,6 +82,7 @@ Example: regmap-mcba = <&mcba>; regmap-mcbb = <&mcbb>; regmap-efuse = <&efuse>; + regmap-rb = <&rb>; reg = <0x0 0x78800000 0x0 0x100>; interrupts = <0x0 0x20 0x4>, <0x0 0x21 0x4>, diff --git a/Documentation/devicetree/bindings/goldfish/battery.txt b/Documentation/devicetree/bindings/goldfish/battery.txt new file mode 100644 index 000000000000..4fb613933214 --- /dev/null +++ b/Documentation/devicetree/bindings/goldfish/battery.txt @@ -0,0 +1,17 @@ +Android Goldfish Battery + +Android goldfish battery device generated by android emulator. + +Required properties: + +- compatible : should contain "google,goldfish-battery" to match emulator +- reg : <registers mapping> +- interrupts : <interrupt mapping> + +Example: + + goldfish_battery@9020000 { + compatible = "google,goldfish-battery"; + reg = <0x9020000 0x1000>; + interrupts = <0x3>; + }; diff --git a/Documentation/devicetree/bindings/goldfish/pipe.txt b/Documentation/devicetree/bindings/goldfish/pipe.txt new file mode 100644 index 000000000000..e417a31a1ee3 --- /dev/null +++ b/Documentation/devicetree/bindings/goldfish/pipe.txt @@ -0,0 +1,17 @@ +Android Goldfish QEMU Pipe + +Andorid pipe virtual device generated by android emulator. + +Required properties: + +- compatible : should contain "google,android-pipe" to match emulator +- reg : <registers mapping> +- interrupts : <interrupt mapping> + +Example: + + android_pipe@a010000 { + compatible = "google,android-pipe"; + reg = <ff018000 0x2000>; + interrupts = <0x12>; + }; diff --git a/Documentation/devicetree/bindings/goldfish/tty.txt b/Documentation/devicetree/bindings/goldfish/tty.txt new file mode 100644 index 000000000000..82648278da77 --- /dev/null +++ b/Documentation/devicetree/bindings/goldfish/tty.txt @@ -0,0 +1,17 @@ +Android Goldfish TTY + +Android goldfish tty device generated by android emulator. + +Required properties: + +- compatible : should contain "google,goldfish-tty" to match emulator +- reg : <registers mapping> +- interrupts : <interrupt mapping> + +Example: + + goldfish_tty@1f004000 { + compatible = "google,goldfish-tty"; + reg = <0x1f004000 0x1000>; + interrupts = <0xc>; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-altera.txt b/Documentation/devicetree/bindings/gpio/gpio-altera.txt index 12f50149e1ed..826a7208ca93 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-altera.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-altera.txt @@ -12,7 +12,7 @@ Required properties: - #interrupt-cells : Should be 1. The interrupt type is fixed in the hardware. - The first cell is the GPIO offset number within the GPIO controller. - interrupts: Specify the interrupt. -- altr,interrupt-trigger: Specifies the interrupt trigger type the GPIO +- altr,interrupt-type: Specifies the interrupt trigger type the GPIO hardware is synthesized. This field is required if the Altera GPIO controller used has IRQ enabled as the interrupt type is not software controlled, but hardware synthesized. Required if GPIO is used as an interrupt @@ -35,7 +35,7 @@ gpio_altr: gpio@0xff200000 { reg = <0xff200000 0x10>; interrupts = <0 45 4>; altr,ngpio = <32>; - altr,interrupt-trigger = <IRQ_TYPE_EDGE_RISING>; + altr,interrupt-type = <IRQ_TYPE_EDGE_RISING>; #gpio-cells = <2>; gpio-controller; #interrupt-cells = <1>; diff --git a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt index f3332b9a8ed4..c934106b10aa 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-mcp23s08.txt @@ -10,6 +10,7 @@ Required properties: - "microchip,mcp23s08" for 8 GPIO SPI version - "microchip,mcp23s17" for 16 GPIO SPI version + - "microchip,mcp23s18" for 16 GPIO SPI version - "microchip,mcp23008" for 8 GPIO I2C version or - "microchip,mcp23017" for 16 GPIO I2C version of the chip NOTE: Do not use the old mcp prefix any more. It is deprecated and will be @@ -43,9 +44,6 @@ Optional properties: - first cell is the pin number - second cell is used to specify flags. - interrupt-controller: Marks the device node as a interrupt controller. -NOTE: The interrupt functionality is only supported for i2c versions of the -chips. The spi chips can also do the interrupts, but this is not supported by -the linux driver yet. Optional device specific properties: - microchip,irq-mirror: Sets the mirror flag in the IOCON register. Devices diff --git a/Documentation/devicetree/bindings/gpio/gpio-pisosr.txt b/Documentation/devicetree/bindings/gpio/gpio-pisosr.txt new file mode 100644 index 000000000000..414a01cdf715 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-pisosr.txt @@ -0,0 +1,34 @@ +Generic Parallel-in/Serial-out Shift Register GPIO Driver + +This binding describes generic parallel-in/serial-out shift register +devices that can be used for GPI (General Purpose Input). This includes +SN74165 serial-out shift registers and the SN65HVS88x series of +industrial serializers. + +Required properties: + - compatible : Should be "pisosr-gpio". + - gpio-controller : Marks the device node as a GPIO controller. + - #gpio-cells : Should be two. For consumer use see gpio.txt. + +Optional properties: + - ngpios : Number of used GPIO lines (0..n-1), default is 8. + - load-gpios : GPIO pin specifier attached to load enable, this + pin is pulsed before reading from the device to + load input pin values into the the device. + +For other required and optional properties of SPI slave +nodes please refer to ../spi/spi-bus.txt. + +Example: + + gpio@0 { + compatible = "ti,sn65hvs882", "pisosr-gpio"; + gpio-controller; + #gpio-cells = <2>; + + load-gpios = <&gpio2 23 GPIO_ACTIVE_LOW>; + + reg = <0>; + spi-max-frequency = <1000000>; + spi-cpol; + }; diff --git a/Documentation/devicetree/bindings/gpio/gpio-ts4800.txt b/Documentation/devicetree/bindings/gpio/gpio-ts4800.txt new file mode 100644 index 000000000000..92ea9c8f6399 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-ts4800.txt @@ -0,0 +1,20 @@ +* TS-4800 FPGA's GPIO controller bindings + +Required properties: +- compatible: Must be "technologic,ts4800-gpio". +- #gpio-cells: Should be two. The first cell is the pin number. +- reg: Physical base address of the controller and length + of memory mapped region. + +Optional property: +- ngpios: See "gpio.txt" + +Example: + +gpio1: gpio { + compatible = "technologic,ts4800-gpio"; + reg = <0x10020 0x6>; + ngpios = <8>; + gpio-controller; + #gpio-cells = <2>; +}; diff --git a/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt b/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt index dae130060537..5490c1d68981 100644 --- a/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt +++ b/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt @@ -1,10 +1,20 @@ APM X-Gene Standby GPIO controller bindings -This is a gpio controller in the standby domain. - -There are 20 GPIO pins from 0..21. There is no GPIO_DS14 or GPIO_DS15, -only GPIO_DS8..GPIO_DS13 support interrupts. The IRQ mapping -is currently 1-to-1 on interrupts 0x28 thru 0x2d. +This is a gpio controller in the standby domain. It also supports interrupt in +some particular pins which are sourced to its parent interrupt controller +as diagram below: + +-----------------+ + | X-Gene standby | + | GPIO controller +------ GPIO_0 ++------------+ | | ... +| Parent IRQ | EXT_INT_0 | +------ GPIO_8/EXT_INT_0 +| controller | (SPI40) | | ... +| (GICv2) +--------------+ +------ GPIO_[N+8]/EXT_INT_N +| | ... | | +| | EXT_INT_N | +------ GPIO_[N+9] +| | (SPI[40 + N])| | ... +| +--------------+ +------ GPIO_MAX ++------------+ +-----------------+ Required properties: - compatible: "apm,xgene-gpio-sb" for the X-Gene Standby GPIO controller @@ -15,10 +25,18 @@ Required properties: 0 = active high 1 = active low - gpio-controller: Marks the device node as a GPIO controller. -- interrupts: Shall contain exactly 6 interrupts. +- interrupts: The EXT_INT_0 parent interrupt resource must be listed first. +- interrupt-parent: Phandle of the parent interrupt controller. +- interrupt-cells: Should be two. + - first cell is 0-N coresponding for EXT_INT_0 to EXT_INT_N. + - second cell is used to specify flags. +- interrupt-controller: Marks the device node as an interrupt controller. +- apm,nr-gpios: Optional, specify number of gpios pin. +- apm,nr-irqs: Optional, specify number of interrupt pins. +- apm,irq-start: Optional, specify lowest gpio pin support interrupt. Example: - sbgpio: sbgpio@17001000 { + sbgpio: gpio@17001000{ compatible = "apm,xgene-gpio-sb"; reg = <0x0 0x17001000 0x0 0x400>; #gpio-cells = <2>; @@ -29,4 +47,19 @@ Example: <0x0 0x2b 0x1>, <0x0 0x2c 0x1>, <0x0 0x2d 0x1>; + interrupt-parent = <&gic>; + #interrupt-cells = <2>; + interrupt-controller; + apm,nr-gpios = <22>; + apm,nr-irqs = <6>; + apm,irq-start = <8>; + }; + + testuser { + compatible = "example,testuser"; + /* Use the GPIO_13/EXT_INT_5 line as an active high triggered + * level interrupt + */ + interrupts = <5 4>; + interrupt-parent = <&sbgpio>; }; diff --git a/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt b/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt new file mode 100644 index 000000000000..ef3752889496 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/microchip,pic32-gpio.txt @@ -0,0 +1,49 @@ +* Microchip PIC32 GPIO devices (PIO). + +Required properties: + - compatible: "microchip,pic32mzda-gpio" + - reg: Base address and length for the device. + - interrupts: The port interrupt shared by all pins. + - gpio-controller: Marks the port as GPIO controller. + - #gpio-cells: Two. The first cell is the pin number and + the second cell is used to specify the gpio polarity as defined in + defined in <dt-bindings/gpio/gpio.h>: + 0 = GPIO_ACTIVE_HIGH + 1 = GPIO_ACTIVE_LOW + 2 = GPIO_OPEN_DRAIN + - interrupt-controller: Marks the device node as an interrupt controller. + - #interrupt-cells: Two. The first cell is the GPIO number and second cell + is used to specify the trigger type as defined in + <dt-bindings/interrupt-controller/irq.h>: + IRQ_TYPE_EDGE_RISING + IRQ_TYPE_EDGE_FALLING + IRQ_TYPE_EDGE_BOTH + - clocks: Clock specifier (see clock bindings for details). + - microchip,gpio-bank: Specifies which bank a controller owns. + - gpio-ranges: Interaction with the PINCTRL subsystem. + +Example: + +/* PORTA */ +gpio0: gpio0@1f860000 { + compatible = "microchip,pic32mzda-gpio"; + reg = <0x1f860000 0x100>; + interrupts = <118 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + gpio-controller; + interrupt-controller; + #interrupt-cells = <2>; + clocks = <&PBCLK4>; + microchip,gpio-bank = <0>; + gpio-ranges = <&pic32_pinctrl 0 0 16>; +}; + +keys { + ... + + button@sw1 { + label = "ESC"; + linux,code = <1>; + gpios = <&gpio0 12 0>; + }; +}; diff --git a/Documentation/devicetree/bindings/hsi/nokia-modem.txt b/Documentation/devicetree/bindings/hsi/nokia-modem.txt index 8a979780452b..53de1d9d0b95 100644 --- a/Documentation/devicetree/bindings/hsi/nokia-modem.txt +++ b/Documentation/devicetree/bindings/hsi/nokia-modem.txt @@ -7,6 +7,8 @@ properties are needed by the Nokia modem HSI client: Required properties: - compatible: Should be one of "nokia,n900-modem" + "nokia,n950-modem" + "nokia,n9-modem" - hsi-channel-names: Should contain the following strings "mcsaab-control" "speech-control" @@ -15,11 +17,11 @@ Required properties: - gpios: Should provide a GPIO handler for each GPIO listed in gpio-names - gpio-names: Should contain the following strings - "cmt_apeslpx" - "cmt_rst_rq" - "cmt_en" - "cmt_rst" - "cmt_bsi" + "cmt_apeslpx" (for n900, n950, n9) + "cmt_rst_rq" (for n900, n950, n9) + "cmt_en" (for n900, n950, n9) + "cmt_rst" (for n900) + "cmt_bsi" (for n900) - interrupts: Should be IRQ handle for modem's reset indication Example: diff --git a/Documentation/devicetree/bindings/hwmon/nsa320-mcu.txt b/Documentation/devicetree/bindings/hwmon/nsa320-mcu.txt new file mode 100644 index 000000000000..0863e067c85b --- /dev/null +++ b/Documentation/devicetree/bindings/hwmon/nsa320-mcu.txt @@ -0,0 +1,20 @@ +Bindings for the fan / temperature monitor microcontroller used on +the Zyxel NSA 320 and several subsequent models. + +Required properties: +- compatible : "zyxel,nsa320-mcu" +- data-gpios : The GPIO pin connected to the data line on the MCU +- clk-gpios : The GPIO pin connected to the clock line on the MCU +- act-gpios : The GPIO pin connected to the active line on the MCU + +Example: + + hwmon { + compatible = "zyxel,nsa320-mcu"; + pinctrl-0 = <&pmx_mcu_data &pmx_mcu_clk &pmx_mcu_act>; + pinctrl-names = "default"; + + data-gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; + clk-gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>; + act-gpios = <&gpio0 17 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt index a04a80f9cc70..c3b9c4cfe8df 100644 --- a/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt +++ b/Documentation/devicetree/bindings/hwmon/ntc_thermistor.txt @@ -10,6 +10,7 @@ Requires node properties: "murata,ncp03wb473" "murata,ncp15wl333" "murata,ncp03wf104" + "murata,ncp15xh103" /* Usage of vendor name "ntc" is deprecated */ <DEPRECATED> "ntc,ncp15wb473" diff --git a/Documentation/devicetree/bindings/iio/iio-bindings.txt b/Documentation/devicetree/bindings/iio/iio-bindings.txt index 0b447d9ad196..68d6f8ce063b 100644 --- a/Documentation/devicetree/bindings/iio/iio-bindings.txt +++ b/Documentation/devicetree/bindings/iio/iio-bindings.txt @@ -82,7 +82,7 @@ vdd channel is connected to output 0 of the &ref device. ... - iio_hwmon { + iio-hwmon { compatible = "iio-hwmon"; io-channels = <&adc 0>, <&adc 1>, <&adc 2>, <&adc 3>, <&adc 4>, <&adc 5>, diff --git a/Documentation/devicetree/bindings/interrupt-controller/al,alpine-msix.txt b/Documentation/devicetree/bindings/interrupt-controller/al,alpine-msix.txt new file mode 100644 index 000000000000..f6f1c14bf99b --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/al,alpine-msix.txt @@ -0,0 +1,26 @@ +Alpine MSIX controller + +See arm,gic-v3.txt for SPI and MSI definitions. + +Required properties: + +- compatible: should be "al,alpine-msix" +- reg: physical base address and size of the registers +- interrupt-parent: specifies the parent interrupt controller. +- interrupt-controller: identifies the node as an interrupt controller +- msi-controller: identifies the node as an PCI Message Signaled Interrupt + controller +- al,msi-base-spi: SPI base of the MSI frame +- al,msi-num-spis: number of SPIs assigned to the MSI frame, relative to SPI0 + +Example: + +msix: msix { + compatible = "al,alpine-msix"; + reg = <0x0 0xfbe00000 0x0 0x100000>; + interrupt-parent = <&gic>; + interrupt-controller; + msi-controller; + al,msi-base-spi = <160>; + al,msi-num-spis = <160>; +}; diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt index 5a1cb4bc3dfe..793c20ff8fcc 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt @@ -16,6 +16,7 @@ Main node required properties: "arm,cortex-a15-gic" "arm,cortex-a7-gic" "arm,cortex-a9-gic" + "arm,eb11mp-gic" "arm,gic-400" "arm,pl390" "arm,tc11mp-gic" diff --git a/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt b/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt new file mode 100644 index 000000000000..8af0a8e613ab --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/marvell,odmi-controller.txt @@ -0,0 +1,44 @@ + +* Marvell ODMI for MSI support + +Some Marvell SoCs have an On-Die Message Interrupt (ODMI) controller +which can be used by on-board peripheral for MSI interrupts. + +Required properties: + +- compatible : The value here should contain: + + "marvell,ap806-odmi-controller", "marvell,odmi-controller". + +- interrupt,controller : Identifies the node as an interrupt controller. + +- msi-controller : Identifies the node as an MSI controller. + +- marvell,odmi-frames : Number of ODMI frames available. Each frame + provides a number of events. + +- reg : List of register definitions, one for each + ODMI frame. + +- marvell,spi-base : List of GIC base SPI interrupts, one for each + ODMI frame. Those SPI interrupts are 0-based, + i.e marvell,spi-base = <128> will use SPI #96. + See Documentation/devicetree/bindings/interrupt-controller/arm,gic.txt + for details about the GIC Device Tree binding. + +- interrupt-parent : Reference to the parent interrupt controller. + +Example: + + odmi: odmi@300000 { + compatible = "marvell,ap806-odm-controller", + "marvell,odmi-controller"; + interrupt-controller; + msi-controller; + marvell,odmi-frames = <4>; + reg = <0x300000 0x4000>, + <0x304000 0x4000>, + <0x308000 0x4000>, + <0x30C000 0x4000>; + marvell,spi-base = <128>, <136>, <144>, <152>; + }; diff --git a/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt b/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt index aae4c384ee1f..173595305e26 100644 --- a/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt +++ b/Documentation/devicetree/bindings/interrupt-controller/mips-gic.txt @@ -23,6 +23,12 @@ Optional properties: - mti,reserved-cpu-vectors : Specifies the list of CPU interrupt vectors to which the GIC may not route interrupts. Valid values are 2 - 7. This property is ignored if the CPU is started in EIC mode. +- mti,reserved-ipi-vectors : Specifies the range of GIC interrupts that are + reserved for IPIs. + It accepts 2 values, the 1st is the starting interrupt and the 2nd is the size + of the reserved range. + If not specified, the driver will allocate the last 2 * number of VPEs in the + system. Required properties for timer sub-node: - compatible : Should be "mti,gic-timer". @@ -44,6 +50,7 @@ Example: #interrupt-cells = <3>; mti,reserved-cpu-vectors = <7>; + mti,reserved-ipi-vectors = <40 8>; timer { compatible = "mti,gic-timer"; diff --git a/Documentation/devicetree/bindings/interrupt-controller/sigma,smp8642-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/sigma,smp8642-intc.txt new file mode 100644 index 000000000000..1f441fa0ad40 --- /dev/null +++ b/Documentation/devicetree/bindings/interrupt-controller/sigma,smp8642-intc.txt @@ -0,0 +1,49 @@ +Sigma Designs SMP86xx/SMP87xx secondary interrupt controller + +Required properties: +- compatible: should be "sigma,smp8642-intc" +- reg: physical address of MMIO region +- ranges: address space mapping of child nodes +- interrupt-parent: phandle of parent interrupt controller +- interrupt-controller: boolean +- #address-cells: should be <1> +- #size-cells: should be <1> + +One child node per control block with properties: +- reg: address of registers for this control block +- interrupt-controller: boolean +- #interrupt-cells: should be <2>, interrupt index and flags per interrupts.txt +- interrupts: interrupt spec of primary interrupt controller + +Example: + +interrupt-controller@6e000 { + compatible = "sigma,smp8642-intc"; + reg = <0x6e000 0x400>; + ranges = <0x0 0x6e000 0x400>; + interrupt-parent = <&gic>; + interrupt-controller; + #address-cells = <1>; + #size-cells = <1>; + + irq0: interrupt-controller@0 { + reg = <0x000 0x100>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; + }; + + irq1: interrupt-controller@100 { + reg = <0x100 0x100>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; + }; + + irq2: interrupt-controller@300 { + reg = <0x300 0x100>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/leds/leds-is31fl32xx.txt b/Documentation/devicetree/bindings/leds/leds-is31fl32xx.txt new file mode 100644 index 000000000000..926c2117942c --- /dev/null +++ b/Documentation/devicetree/bindings/leds/leds-is31fl32xx.txt @@ -0,0 +1,52 @@ +Binding for ISSI IS31FL32xx and Si-En SN32xx LED Drivers + +The IS31FL32xx/SN32xx family of LED drivers are I2C devices with multiple +constant-current channels, each with independent 256-level PWM control. +Each LED is represented as a sub-node of the device. + +Required properties: +- compatible: one of + issi,is31fl3236 + issi,is31fl3235 + issi,is31fl3218 + issi,is31fl3216 + si-en,sn3218 + si-en,sn3216 +- reg: I2C slave address +- address-cells : must be 1 +- size-cells : must be 0 + +LED sub-node properties: +- reg : LED channel number (1..N) +- label : (optional) + see Documentation/devicetree/bindings/leds/common.txt +- linux,default-trigger : (optional) + see Documentation/devicetree/bindings/leds/common.txt + + +Example: + +is31fl3236: led-controller@3c { + compatible = "issi,is31fl3236"; + reg = <0x3c>; + #address-cells = <1>; + #size-cells = <0>; + + led@1 { + reg = <1>; + label = "EB:blue:usr0"; + }; + led@2 { + reg = <2>; + label = "EB:blue:usr1"; + }; + ... + led@36 { + reg = <36>; + label = "EB:blue:usr35"; + }; +}; + +For more product information please see the links below: +http://www.issi.com/US/product-analog-fxled-driver.shtml +http://www.si-en.com/product.asp?parentid=890 diff --git a/Documentation/devicetree/bindings/media/i2c/mt9v032.txt b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt index 202565313e82..100f0ae43269 100644 --- a/Documentation/devicetree/bindings/media/i2c/mt9v032.txt +++ b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt @@ -20,6 +20,8 @@ Optional Properties: - link-frequencies: List of allowed link frequencies in Hz. Each frequency is expressed as a 64-bit big-endian integer. +- reset-gpios: GPIO handle which is connected to the reset pin of the chip. +- standby-gpios: GPIO handle which is connected to the standby pin of the chip. For further reading on port node refer to Documentation/devicetree/bindings/media/video-interfaces.txt. diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt new file mode 100644 index 000000000000..8c0fc1a26bf0 --- /dev/null +++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt @@ -0,0 +1,45 @@ +* Texas Instruments TVP5150 and TVP5151 video decoders + +The TVP5150 and TVP5151 are video decoders that convert baseband NTSC and PAL +(and also SECAM in the TVP5151 case) video signals to either 8-bit 4:2:2 YUV +with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats. + +Required Properties: +- compatible: value must be "ti,tvp5150" +- reg: I2C slave address + +Optional Properties: +- pdn-gpios: phandle for the GPIO connected to the PDN pin, if any. +- reset-gpios: phandle for the GPIO connected to the RESETB pin, if any. + +The device node must contain one 'port' child node for its digital output +video port, in accordance with the video interface bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Required Endpoint Properties for parallel synchronization: + +- hsync-active: active state of the HSYNC signal. Must be <1> (HIGH). +- vsync-active: active state of the VSYNC signal. Must be <1> (HIGH). +- field-even-active: field signal level during the even field data + transmission. Must be <0>. + +If none of hsync-active, vsync-active and field-even-active is specified, +the endpoint is assumed to use embedded BT.656 synchronization. + +Example: + +&i2c2 { + ... + tvp5150@5c { + compatible = "ti,tvp5150"; + reg = <0x5c>; + pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>; + + port { + tvp5150_1: endpoint { + remote-endpoint = <&ccdc_ep>; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt index 9dafe6b06cd2..619193ccf7ff 100644 --- a/Documentation/devicetree/bindings/media/rcar_vin.txt +++ b/Documentation/devicetree/bindings/media/rcar_vin.txt @@ -6,6 +6,7 @@ family of devices. The current blocks are always slaves and suppot one input channel which can be either RGB, YUYV or BT656. - compatible: Must be one of the following + - "renesas,vin-r8a7795" for the R8A7795 device - "renesas,vin-r8a7794" for the R8A7794 device - "renesas,vin-r8a7793" for the R8A7793 device - "renesas,vin-r8a7791" for the R8A7791 device diff --git a/Documentation/devicetree/bindings/media/renesas,jpu.txt b/Documentation/devicetree/bindings/media/renesas,jpu.txt index 0cb94201bf92..d3436e5190f9 100644 --- a/Documentation/devicetree/bindings/media/renesas,jpu.txt +++ b/Documentation/devicetree/bindings/media/renesas,jpu.txt @@ -5,11 +5,12 @@ and decoding function conforming to the JPEG baseline process, so that the JPU can encode image data and decode JPEG data quickly. Required properties: - - compatible: should containg one of the following: - - "renesas,jpu-r8a7790" for R-Car H2 - - "renesas,jpu-r8a7791" for R-Car M2-W - - "renesas,jpu-r8a7792" for R-Car V2H - - "renesas,jpu-r8a7793" for R-Car M2-N +- compatible: "renesas,jpu-<soctype>", "renesas,rcar-gen2-jpu" as fallback. + Examples with soctypes are: + - "renesas,jpu-r8a7790" for R-Car H2 + - "renesas,jpu-r8a7791" for R-Car M2-W + - "renesas,jpu-r8a7792" for R-Car V2H + - "renesas,jpu-r8a7793" for R-Car M2-N - reg: Base address and length of the registers block for the JPU. - interrupts: JPU interrupt specifier. @@ -17,7 +18,7 @@ Required properties: Example: R8A7790 (R-Car H2) JPU node jpeg-codec@fe980000 { - compatible = "renesas,jpu-r8a7790"; + compatible = "renesas,jpu-r8a7790", "renesas,rcar-gen2-jpu"; reg = <0 0xfe980000 0 0x10300>; interrupts = <0 272 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp1_clks R8A7790_CLK_JPU>; diff --git a/Documentation/devicetree/bindings/media/renesas,vsp1.txt b/Documentation/devicetree/bindings/media/renesas,vsp1.txt index 87fe08abf36d..627405abd144 100644 --- a/Documentation/devicetree/bindings/media/renesas,vsp1.txt +++ b/Documentation/devicetree/bindings/media/renesas,vsp1.txt @@ -1,30 +1,18 @@ -* Renesas VSP1 Video Processing Engine +* Renesas VSP Video Processing Engine -The VSP1 is a video processing engine that supports up-/down-scaling, alpha +The VSP is a video processing engine that supports up-/down-scaling, alpha blending, color space conversion and various other image processing features. It can be found in the Renesas R-Car second generation SoCs. Required properties: - - compatible: Must contain "renesas,vsp1" + - compatible: Must contain one of the following values + - "renesas,vsp1" for the R-Car Gen2 VSP1 + - "renesas,vsp2" for the R-Car Gen3 VSP2 - - reg: Base address and length of the registers block for the VSP1. - - interrupts: VSP1 interrupt specifier. - - clocks: A phandle + clock-specifier pair for the VSP1 functional clock. - - - renesas,#rpf: Number of Read Pixel Formatter (RPF) modules in the VSP1. - - renesas,#uds: Number of Up Down Scaler (UDS) modules in the VSP1. - - renesas,#wpf: Number of Write Pixel Formatter (WPF) modules in the VSP1. - - -Optional properties: - - - renesas,has-lif: Boolean, indicates that the LCD Interface (LIF) module is - available. - - renesas,has-lut: Boolean, indicates that the Look Up Table (LUT) module is - available. - - renesas,has-sru: Boolean, indicates that the Super Resolution Unit (SRU) - module is available. + - reg: Base address and length of the registers block for the VSP. + - interrupts: VSP interrupt specifier. + - clocks: A phandle + clock-specifier pair for the VSP functional clock. Example: R8A7790 (R-Car H2) VSP1-S node @@ -34,10 +22,4 @@ Example: R8A7790 (R-Car H2) VSP1-S node reg = <0 0xfe928000 0 0x8000>; interrupts = <0 267 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp1_clks R8A7790_CLK_VSP1_S>; - - renesas,has-lut; - renesas,has-sru; - renesas,#rpf = <5>; - renesas,#uds = <3>; - renesas,#wpf = <4>; }; diff --git a/Documentation/devicetree/bindings/media/ti-cal.txt b/Documentation/devicetree/bindings/media/ti-cal.txt new file mode 100644 index 000000000000..ae9b52f37576 --- /dev/null +++ b/Documentation/devicetree/bindings/media/ti-cal.txt @@ -0,0 +1,72 @@ +Texas Instruments DRA72x CAMERA ADAPTATION LAYER (CAL) +------------------------------------------------------ + +The Camera Adaptation Layer (CAL) is a key component for image capture +applications. The capture module provides the system interface and the +processing capability to connect CSI2 image-sensor modules to the +DRA72x device. + +Required properties: +- compatible: must be "ti,dra72-cal" +- reg: CAL Top level, Receiver Core #0, Receiver Core #1 and Camera RX + control address space +- reg-names: cal_top, cal_rx_core0, cal_rx_core1, and camerrx_control + registers +- interrupts: should contain IRQ line for the CAL; + +CAL supports 2 camera port nodes on MIPI bus. Each CSI2 camera port nodes +should contain a 'port' child node with child 'endpoint' node. Please +refer to the bindings defined in +Documentation/devicetree/bindings/media/video-interfaces.txt. + +Example: + cal: cal@4845b000 { + compatible = "ti,dra72-cal"; + ti,hwmods = "cal"; + reg = <0x4845B000 0x400>, + <0x4845B800 0x40>, + <0x4845B900 0x40>, + <0x4A002e94 0x4>; + reg-names = "cal_top", + "cal_rx_core0", + "cal_rx_core1", + "camerrx_control"; + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + csi2_0: port@0 { + reg = <0>; + endpoint { + slave-mode; + remote-endpoint = <&ar0330_1>; + }; + }; + csi2_1: port@1 { + reg = <1>; + }; + }; + }; + + i2c5: i2c@4807c000 { + ar0330@10 { + compatible = "ti,ar0330"; + reg = <0x10>; + + port { + #address-cells = <1>; + #size-cells = <0>; + + ar0330_1: endpoint { + reg = <0>; + clock-lanes = <1>; + data-lanes = <0 2 3 4>; + remote-endpoint = <&csi2_0>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mfd/tps65912.txt b/Documentation/devicetree/bindings/mfd/tps65912.txt new file mode 100644 index 000000000000..717e66d23142 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/tps65912.txt @@ -0,0 +1,50 @@ +* TPS65912 Power Management Integrated Circuit bindings + +Required properties: + - compatible : Should be "ti,tps65912". + - reg : Slave address or chip select number (I2C / SPI). + - interrupt-parent : The parent interrupt controller. + - interrupts : The interrupt line the device is connected to. + - interrupt-controller : Marks the device node as an interrupt controller. + - #interrupt-cells : The number of cells to describe an IRQ, should be 2. + The first cell is the IRQ number. + The second cell is the flags, encoded as trigger + masks from ../interrupt-controller/interrupts.txt. + - gpio-controller : Marks the device node as a GPIO Controller. + - #gpio-cells : Should be two. The first cell is the pin number and + the second cell is used to specify flags. + See ../gpio/gpio.txt for more information. + - regulators: : List of child nodes that specify the regulator + initialization data. Child nodes must be named + after their hardware counterparts: dcdc[1-4] and + ldo[1-10]. Each child nodes is defined using the + standard binding for regulators. + +Example: + + pmic: tps65912@2d { + compatible = "ti,tps65912"; + reg = <0x2d>; + interrupt-parent = <&gpio1>; + interrupts = <28 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + + regulators { + dcdc1 { + regulator-name = "vdd_core"; + regulator-min-microvolt = <912000>; + regulator-max-microvolt = <1144000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <1900000>; + regulator-max-microvolt = <1900000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/misc/eeprom-93xx46.txt b/Documentation/devicetree/bindings/misc/eeprom-93xx46.txt new file mode 100644 index 000000000000..a8ebb4621f79 --- /dev/null +++ b/Documentation/devicetree/bindings/misc/eeprom-93xx46.txt @@ -0,0 +1,25 @@ +EEPROMs (SPI) compatible with Microchip Technology 93xx46 family. + +Required properties: +- compatible : shall be one of: + "atmel,at93c46d" + "eeprom-93xx46" +- data-size : number of data bits per word (either 8 or 16) + +Optional properties: +- read-only : parameter-less property which disables writes to the EEPROM +- select-gpios : if present, specifies the GPIO that will be asserted prior to + each access to the EEPROM (e.g. for SPI bus multiplexing) + +Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt +apply. In particular, "reg" and "spi-max-frequency" properties must be given. + +Example: + eeprom@0 { + compatible = "eeprom-93xx46"; + reg = <0>; + spi-max-frequency = <1000000>; + spi-cs-high; + data-size = <8>; + select-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/nvmem/lpc1857-eeprom.txt b/Documentation/devicetree/bindings/nvmem/lpc1857-eeprom.txt new file mode 100644 index 000000000000..809df68f6e14 --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/lpc1857-eeprom.txt @@ -0,0 +1,28 @@ +* NXP LPC18xx EEPROM memory NVMEM driver + +Required properties: + - compatible: Should be "nxp,lpc1857-eeprom" + - reg: Must contain an entry with the physical base address and length + for each entry in reg-names. + - reg-names: Must include the following entries. + - reg: EEPROM registers. + - mem: EEPROM address space. + - clocks: Must contain an entry for each entry in clock-names. + - clock-names: Must include the following entries. + - eeprom: EEPROM operating clock. + - resets: Should contain a reference to the reset controller asserting + the EEPROM in reset. + - interrupts: Should contain EEPROM interrupt. + +Example: + + eeprom: eeprom@4000e000 { + compatible = "nxp,lpc1857-eeprom"; + reg = <0x4000e000 0x1000>, + <0x20040000 0x4000>; + reg-names = "reg", "mem"; + clocks = <&ccu1 CLK_CPU_EEPROM>; + clock-names = "eeprom"; + resets = <&rgu 27>; + interrupts = <4>; + }; diff --git a/Documentation/devicetree/bindings/nvmem/mtk-efuse.txt b/Documentation/devicetree/bindings/nvmem/mtk-efuse.txt new file mode 100644 index 000000000000..74cf52908a6c --- /dev/null +++ b/Documentation/devicetree/bindings/nvmem/mtk-efuse.txt @@ -0,0 +1,36 @@ += Mediatek MTK-EFUSE device tree bindings = + +This binding is intended to represent MTK-EFUSE which is found in most Mediatek SOCs. + +Required properties: +- compatible: should be "mediatek,mt8173-efuse" or "mediatek,efuse" +- reg: Should contain registers location and length + += Data cells = +Are child nodes of MTK-EFUSE, bindings of which as described in +bindings/nvmem/nvmem.txt + +Example: + + efuse: efuse@10206000 { + compatible = "mediatek,mt8173-efuse"; + reg = <0 0x10206000 0 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + /* Data cells */ + thermal_calibration: calib@528 { + reg = <0x528 0xc>; + }; + }; + += Data consumers = +Are device nodes which consume nvmem data cells. + +For example: + + thermal { + ... + nvmem-cells = <&thermal_calibration>; + nvmem-cell-names = "calibration"; + }; diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index 5b0853df9d5a..64f2fff12128 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -28,3 +28,20 @@ Optional properties: - clock-names: Must include the following entries: - "pcie" - "pcie_bus" + +Example configuration: + + pcie: pcie@0xdffff000 { + compatible = "snps,dw-pcie"; + reg = <0xdffff000 0x1000>, /* Controller registers */ + <0xd0000000 0x2000>; /* PCI config space */ + reg-names = "ctrlreg", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0x00000000 0xde000000 0 0x00010000 + 0x82000000 0 0xd0400000 0xd0400000 0 0x0d000000>; + interrupts = <25>, <24>; + #interrupt-cells = <1>; + num-lanes = <1>; + }; diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index 6fbba53a309b..3be80c68941a 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -13,6 +13,13 @@ Required properties: - clock-names: Must include the following additional entries: - "pcie_phy" +Optional properties: +- fsl,tx-deemph-gen1: Gen1 De-emphasis value. Default: 0 +- fsl,tx-deemph-gen2-3p5db: Gen2 (3.5db) De-emphasis value. Default: 0 +- fsl,tx-deemph-gen2-6db: Gen2 (6db) De-emphasis value. Default: 20 +- fsl,tx-swing-full: Gen2 TX SWING FULL value. Default: 127 +- fsl,tx-swing-low: TX launch amplitude swing_low value. Default: 127 + Example: pcie@0x01000000 { diff --git a/Documentation/devicetree/bindings/pci/pci-thunder-ecam.txt b/Documentation/devicetree/bindings/pci/pci-thunder-ecam.txt new file mode 100644 index 000000000000..f478874b79ce --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-thunder-ecam.txt @@ -0,0 +1,30 @@ +* ThunderX PCI host controller for pass-1.x silicon + +Firmware-initialized PCI host controller to on-chip devices found on +some Cavium ThunderX processors. These devices have ECAM-based config +access, but the BARs are all at fixed addresses. We handle the fixed +addresses by synthesizing Enhanced Allocation (EA) capabilities for +these devices. + +The properties and their meanings are identical to those described in +host-generic-pci.txt except as listed below. + +Properties of the host controller node that differ from +host-generic-pci.txt: + +- compatible : Must be "cavium,pci-host-thunder-ecam" + +Example: + + pcie@84b000000000 { + compatible = "cavium,pci-host-thunder-ecam"; + device_type = "pci"; + msi-parent = <&its>; + msi-map = <0 &its 0x30000 0x10000>; + bus-range = <0 31>; + #size-cells = <2>; + #address-cells = <3>; + #stream-id-cells = <1>; + reg = <0x84b0 0x00000000 0 0x02000000>; /* Configuration space */ + ranges = <0x03000000 0x8180 0x00000000 0x8180 0x00000000 0x80 0x00000000>; /* mem ranges */ + }; diff --git a/Documentation/devicetree/bindings/pci/pci-thunder-pem.txt b/Documentation/devicetree/bindings/pci/pci-thunder-pem.txt new file mode 100644 index 000000000000..f131faea3b7c --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-thunder-pem.txt @@ -0,0 +1,43 @@ +* ThunderX PEM PCIe host controller + +Firmware-initialized PCI host controller found on some Cavium +ThunderX processors. + +The properties and their meanings are identical to those described in +host-generic-pci.txt except as listed below. + +Properties of the host controller node that differ from +host-generic-pci.txt: + +- compatible : Must be "cavium,pci-host-thunder-pem" + +- reg : Two entries: First the configuration space for down + stream devices base address and size, as accessed + from the parent bus. Second, the register bank of + the PEM device PCIe bridge. + +Example: + + pci@87e0,c2000000 { + compatible = "cavium,pci-host-thunder-pem"; + device_type = "pci"; + msi-parent = <&its>; + msi-map = <0 &its 0x10000 0x10000>; + bus-range = <0x8f 0xc7>; + #size-cells = <2>; + #address-cells = <3>; + + reg = <0x8880 0x8f000000 0x0 0x39000000>, /* Configuration space */ + <0x87e0 0xc2000000 0x0 0x00010000>; /* PEM space */ + ranges = <0x01000000 0x00 0x00020000 0x88b0 0x00020000 0x00 0x00010000>, /* I/O */ + <0x03000000 0x00 0x10000000 0x8890 0x10000000 0x0f 0xf0000000>, /* mem64 */ + <0x43000000 0x10 0x00000000 0x88a0 0x00000000 0x10 0x00000000>, /* mem64-pref */ + <0x03000000 0x87e0 0xc2f00000 0x87e0 0xc2000000 0x00 0x00100000>; /* mem64 PEM BAR4 */ + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &gic0 0 0 0 24 4>, /* INTA */ + <0 0 0 2 &gic0 0 0 0 25 4>, /* INTB */ + <0 0 0 3 &gic0 0 0 0 26 4>, /* INTC */ + <0 0 0 4 &gic0 0 0 0 27 4>; /* INTD */ + }; diff --git a/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt b/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt new file mode 100644 index 000000000000..337fc97d18c9 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt @@ -0,0 +1,68 @@ +* Xilinx NWL PCIe Root Port Bridge DT description + +Required properties: +- compatible: Should contain "xlnx,nwl-pcie-2.11" +- #address-cells: Address representation for root ports, set to <3> +- #size-cells: Size representation for root ports, set to <2> +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- reg: Should contain Bridge, PCIe Controller registers location, + configuration space, and length +- reg-names: Must include the following entries: + "breg": bridge registers + "pcireg": PCIe controller registers + "cfg": configuration space region +- device_type: must be "pci" +- interrupts: Should contain NWL PCIe interrupt +- interrupt-names: Must include the following entries: + "msi1, msi0": interrupt asserted when MSI is received + "intx": interrupt asserted when a legacy interrupt is received + "misc": interrupt asserted when miscellaneous is received +- interrupt-map-mask and interrupt-map: standard PCI properties to define the + mapping of the PCI interface to interrupt numbers. +- ranges: ranges for the PCI memory regions (I/O space region is not + supported by hardware) + Please refer to the standard PCI bus binding document for a more + detailed explanation +- msi-controller: indicates that this is MSI controller node +- msi-parent: MSI parent of the root complex itself +- legacy-interrupt-controller: Interrupt controller device node for Legacy interrupts + - interrupt-controller: identifies the node as an interrupt controller + - #interrupt-cells: should be set to 1 + - #address-cells: specifies the number of cells needed to encode an + address. The value must be 0. + + +Example: +++++++++ + +nwl_pcie: pcie@fd0e0000 { + #address-cells = <3>; + #size-cells = <2>; + compatible = "xlnx,nwl-pcie-2.11"; + #interrupt-cells = <1>; + msi-controller; + device_type = "pci"; + interrupt-parent = <&gic>; + interrupts = <0 114 4>, <0 115 4>, <0 116 4>, <0 117 4>, <0 118 4>; + interrupt-names = "msi0", "msi1", "intx", "dummy", "misc"; + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = <0x0 0x0 0x0 0x1 &pcie_intc 0x1>, + <0x0 0x0 0x0 0x2 &pcie_intc 0x2>, + <0x0 0x0 0x0 0x3 &pcie_intc 0x3>, + <0x0 0x0 0x0 0x4 &pcie_intc 0x4>; + + msi-parent = <&nwl_pcie>; + reg = <0x0 0xfd0e0000 0x0 0x1000>, + <0x0 0xfd480000 0x0 0x1000>, + <0x0 0xe0000000 0x0 0x1000000>; + reg-names = "breg", "pcireg", "cfg"; + ranges = <0x02000000 0x00000000 0xe1000000 0x00000000 0xe1000000 0 0x0f000000>; + + pcie_intc: legacy-interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + +}; diff --git a/Documentation/devicetree/bindings/pci/xilinx-pcie.txt b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt index 02f979a48aeb..fd57a81180a4 100644 --- a/Documentation/devicetree/bindings/pci/xilinx-pcie.txt +++ b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt @@ -17,7 +17,7 @@ Required properties: Please refer to the standard PCI bus binding document for a more detailed explanation -Optional properties: +Optional properties for Zynq/Microblaze: - bus-range: PCI bus numbers covered Interrupt controller child node @@ -38,13 +38,13 @@ the four INTx interrupts in ISR and route them to this domain. Example: ++++++++ - +Zynq: pci_express: axi-pcie@50000000 { #address-cells = <3>; #size-cells = <2>; #interrupt-cells = <1>; compatible = "xlnx,axi-pcie-host-1.00.a"; - reg = < 0x50000000 0x10000000 >; + reg = < 0x50000000 0x1000000 >; device_type = "pci"; interrupts = < 0 52 4 >; interrupt-map-mask = <0 0 0 7>; @@ -60,3 +60,29 @@ Example: #interrupt-cells = <1>; }; }; + + +Microblaze: + pci_express: axi-pcie@10000000 { + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + compatible = "xlnx,axi-pcie-host-1.00.a"; + reg = <0x10000000 0x4000000>; + device_type = "pci"; + interrupt-parent = <µblaze_0_intc>; + interrupts = <1 2>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 1>, + <0 0 0 2 &pcie_intc 2>, + <0 0 0 3 &pcie_intc 3>, + <0 0 0 4 &pcie_intc 4>; + ranges = <0x02000000 0x00000000 0x80000000 0x80000000 0x00000000 0x10000000>; + + pcie_intc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + }; diff --git a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt index 2390e4e9c84c..eaf7e9b7ce6b 100644 --- a/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt +++ b/Documentation/devicetree/bindings/phy/rcar-gen3-phy-usb2.txt @@ -7,33 +7,26 @@ Required properties: - compatible: "renesas,usb2-phy-r8a7795" if the device is a part of an R8A7795 SoC. - reg: offset and length of the partial USB 2.0 Host register block. -- reg-names: must be "usb2_host". - clocks: clock phandle and specifier pair(s). - #phy-cells: see phy-bindings.txt in the same directory, must be <0>. Optional properties: To use a USB channel where USB 2.0 Host and HSUSB (USB 2.0 Peripheral) are -combined, the device tree node should set HSUSB properties to reg and reg-names -properties. This is because HSUSB has registers to select USB 2.0 host or -peripheral at that channel: -- reg: offset and length of the partial HSUSB register block. -- reg-names: must be "hsusb". +combined, the device tree node should set interrupt properties to use the +channel as USB OTG: - interrupts: interrupt specifier for the PHY. Example (R-Car H3): usb-phy@ee080200 { compatible = "renesas,usb2-phy-r8a7795"; - reg = <0 0xee080200 0 0x700>, <0 0xe6590100 0 0x100>; - reg-names = "usb2_host", "hsusb"; + reg = <0 0xee080200 0 0x700>; interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&mstp7_clks R8A7795_CLK_EHCI0>, - <&mstp7_clks R8A7795_CLK_HSUSB>; + clocks = <&mstp7_clks R8A7795_CLK_EHCI0>; }; usb-phy@ee0a0200 { compatible = "renesas,usb2-phy-r8a7795"; reg = <0 0xee0a0200 0 0x700>; - reg-names = "usb2_host"; clocks = <&mstp7_clks R8A7795_CLK_EHCI0>; }; diff --git a/Documentation/devicetree/bindings/phy/rockchip-dp-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-dp-phy.txt new file mode 100644 index 000000000000..50c4f9b00adf --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip-dp-phy.txt @@ -0,0 +1,22 @@ +Rockchip specific extensions to the Analogix Display Port PHY +------------------------------------ + +Required properties: +- compatible : should be one of the following supported values: + - "rockchip.rk3288-dp-phy" +- clocks: from common clock binding: handle to dp clock. + of memory mapped region. +- clock-names: from common clock binding: + Required elements: "24m" +- rockchip,grf: phandle to the syscon managing the "general register files" +- #phy-cells : from the generic PHY bindings, must be 0; + +Example: + +edp_phy: edp-phy { + compatible = "rockchip,rk3288-dp-phy"; + rockchip,grf = <&grf>; + clocks = <&cru SCLK_EDP_24M>; + clock-names = "24m"; + #phy-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt new file mode 100644 index 000000000000..61916f15a949 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt @@ -0,0 +1,19 @@ +Rockchip EMMC PHY +----------------------- + +Required properties: + - compatible: rockchip,rk3399-emmc-phy + - rockchip,grf : phandle to the syscon managing the "general + register files" + - #phy-cells: must be 0 + - reg: PHY configure reg address offset in "general + register files" + +Example: + +emmcphy: phy { + compatible = "rockchip,rk3399-emmc-phy"; + rockchip,grf = <&grf>; + reg = <0xf780>; + #phy-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt index 9213b27e1036..69617220c5d6 100644 --- a/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/allwinner,sunxi-pinctrl.txt @@ -21,6 +21,8 @@ Required properties: "allwinner,sun9i-a80-r-pinctrl" "allwinner,sun8i-a83t-pinctrl" "allwinner,sun8i-h3-pinctrl" + "allwinner,sun8i-h3-r-pinctrl" + "allwinner,sun50i-a64-pinctrl" - reg: Should contain the register physical address and length for the pin controller. diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,ns2-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/brcm,ns2-pinmux.txt new file mode 100644 index 000000000000..e295dda4bbba --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/brcm,ns2-pinmux.txt @@ -0,0 +1,102 @@ +Broadcom Northstar2 IOMUX Controller + +The Northstar2 IOMUX controller supports group based mux configuration. There +are some individual pins that support modifying the pinconf parameters. + +Required properties: + +- compatible: + Must be "brcm,ns2-pinmux" + +- reg: + Define the base and range of the I/O address space that contains the + Northstar2 IOMUX and pin configuration registers. + +Properties in sub nodes: + +- function: + The mux function to select + +- groups: + The list of groups to select with a given function + +- pins: + List of pin names to change configuration + +The generic properties bias-disable, bias-pull-down, bias-pull-up, +drive-strength, slew-rate, input-enable, input-disable are supported +for some individual pins listed at the end. + +For more details, refer to +Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + +For example: + + pinctrl: pinctrl@6501d130 { + compatible = "brcm,ns2-pinmux"; + reg = <0x6501d130 0x08>, + <0x660a0028 0x04>, + <0x660009b0 0x40>; + + pinctrl-names = "default"; + pinctrl-0 = <&nand_sel &uart3_rx &sdio0_d4>; + + /* Select nand function */ + nand_sel: nand_sel { + function = "nand"; + groups = "nand_grp"; + }; + + /* Pull up the uart3 rx pin */ + uart3_rx: uart3_rx { + pins = "uart3_sin"; + bias-pull-up; + }; + + /* Set the drive strength of sdio d4 pin */ + sdio0_d4: sdio0_d4 { + pins = "sdio0_data4"; + drive-strength = <8>; + }; + }; + +List of supported functions and groups in Northstar2: + +"nand": "nand_grp" + +"nor": "nor_data_grp", "nor_adv_grp", "nor_addr_0_3_grp", "nor_addr_4_5_grp", + "nor_addr_6_7_grp", "nor_addr_8_9_grp", "nor_addr_10_11_grp", + "nor_addr_12_15_grp" + +"gpio": "gpio_0_1_grp", "gpio_2_5_grp", "gpio_6_7_grp", "gpio_8_9_grp", + "gpio_10_11_grp", "gpio_12_13_grp", "gpio_14_17_grp", "gpio_18_19_grp", + "gpio_20_21_grp", "gpio_22_23_grp", "gpio_24_25_grp", "gpio_26_27_grp", + "gpio_28_29_grp", "gpio_30_31_grp" + +"pcie": "pcie_ab1_clk_wak_grp", "pcie_a3_clk_wak_grp", "pcie_b3_clk_wak_grp", + "pcie_b2_clk_wak_grp", "pcie_a2_clk_wak_grp" + +"uart0": "uart0_modem_grp", "uart0_rts_cts_grp", "uart0_in_out_grp" + +"uart1": "uart1_ext_clk_grp", "uart1_dcd_dsr_grp", "uart1_ri_dtr_grp", + "uart1_rts_cts_grp", "uart1_in_out_grp" + +"uart2": "uart2_rts_cts_grp" + +"pwm": "pwm_0_grp", "pwm_1_grp", "pwm_2_grp", "pwm_3_grp" + + +List of pins that support pinconf parameters: + +"qspi_wp", "qspi_hold", "qspi_cs", "qspi_sck", "uart3_sin", "uart3_sout", +"qspi_mosi", "qspi_miso", "spi0_fss", "spi0_rxd", "spi0_txd", "spi0_sck", +"spi1_fss", "spi1_rxd", "spi1_txd", "spi1_sck", "sdio0_data7", +"sdio0_emmc_rst", "sdio0_led_on", "sdio0_wp", "sdio0_data3", "sdio0_data4", +"sdio0_data5", "sdio0_data6", "sdio0_cmd", "sdio0_data0", "sdio0_data1", +"sdio0_data2", "sdio1_led_on", "sdio1_wp", "sdio0_cd_l", "sdio0_clk", +"sdio1_data5", "sdio1_data6", "sdio1_data7", "sdio1_emmc_rst", "sdio1_data1", +"sdio1_data2", "sdio1_data3", "sdio1_data4", "sdio1_cd_l", "sdio1_clk", +"sdio1_cmd", "sdio1_data0", "ext_mdio_0", "ext_mdc_0", "usb3_p1_vbus_ppc", +"usb3_p1_overcurrent", "usb3_p0_vbus_ppc", "usb3_p0_overcurrent", +"usb2_presence_indication", "usb2_vbus_present", "usb2_vbus_ppc", +"usb2_overcurrent", "sata_led1", "sata_led0" diff --git a/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt new file mode 100644 index 000000000000..4b5efa51bec7 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/microchip,pic32-pinctrl.txt @@ -0,0 +1,60 @@ +* Microchip PIC32 Pin Controller + +Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and +../interrupt-controller/interrupts.txt for generic information regarding +pin controller, GPIO, and interrupt bindings. + +PIC32 'pin configuration node' is a node of a group of pins which can be +used for a specific device or function. This node represents configuraions of +pins, optional function, and optional mux related configuration. + +Required properties for pin controller node: + - compatible: "microchip,pic32mada-pinctrl" + - reg: Address range of the pinctrl registers. + - clocks: Clock specifier (see clock bindings for details) + +Required properties for pin configuration sub-nodes: + - pins: List of pins to which the configuration applies. + +Optional properties for pin configuration sub-nodes: +---------------------------------------------------- + - function: Mux function for the specified pins. + - bias-pull-up: Enable weak pull-up. + - bias-pull-down: Enable weak pull-down. + - input-enable: Set the pin as an input. + - output-low: Set the pin as an output level low. + - output-high: Set the pin as an output level high. + - microchip,digital: Enable digital I/O. + - microchip,analog: Enable analog I/O. + +Example: + +pic32_pinctrl: pinctrl@1f801400{ + #address-cells = <1>; + #size-cells = <1>; + compatible = "microchip,pic32mzda-pinctrl"; + reg = <0x1f801400 0x400>; + clocks = <&PBCLK1>; + + pinctrl_uart2: pinctrl_uart2 { + uart2-tx { + pins = "G9"; + function = "U2TX"; + microchip,digital; + output-low; + }; + uart2-rx { + pins = "B0"; + function = "U2RX"; + microchip,digital; + input-enable; + }; + }; +}; + +uart2: serial@1f822200 { + compatible = "microchip,pic32mzda-uart"; + reg = <0x1f822200 0x50>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; +}; diff --git a/Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt b/Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt index df0309c57505..bd8b0c69fa44 100644 --- a/Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt +++ b/Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt @@ -22,6 +22,10 @@ The following generic nodes are supported: - input-schmitt-disable - slew-rate +NXP specific properties: + - nxp,gpio-pin-interrupt : Assign pin to gpio pin interrupt controller + irq number 0 to 7. See example below. + Not all pins support all properties so either refer to the NXP 1850/4350 user manual or the pin table in the pinctrl-lpc18xx driver for supported pin properties. @@ -54,4 +58,14 @@ pinctrl: pinctrl@40086000 { bias-disable; }; }; + + gpio_joystick_pins: gpio-joystick-pins { + gpio_joystick_1_cfg { + pins = "p9_0"; + function = "gpio"; + nxp,gpio-pin-interrupt = <0>; + input-enable; + bias-disable; + }; + }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt index 9ffb0b276bb4..17631d0a9af7 100644 --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt @@ -6,6 +6,7 @@ Required properties: - compatible: value should be one of the following. "mediatek,mt2701-pinctrl", compatible with mt2701 pinctrl. "mediatek,mt6397-pinctrl", compatible with mt6397 pinctrl. + "mediatek,mt7623-pinctrl", compatible with mt7623 pinctrl. "mediatek,mt8127-pinctrl", compatible with mt8127 pinctrl. "mediatek,mt8135-pinctrl", compatible with mt8135 pinctrl. "mediatek,mt8173-pinctrl", compatible with mt8173 pinctrl. diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt new file mode 100644 index 000000000000..cfb8500dd56b --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,ipq4019-pinctrl.txt @@ -0,0 +1,74 @@ +Qualcomm Atheros IPQ4019 TLMM block + +This is the Top Level Mode Multiplexor block found on the Qualcomm IPQ8019 +platform, it provides pinctrl, pinmux, pinconf, and gpiolib facilities. + +Required properties: +- compatible: "qcom,ipq4019-pinctrl" +- reg: Should be the base address and length of the TLMM block. +- interrupts: Should be the parent IRQ of the TLMM block. +- interrupt-controller: Marks the device node as an interrupt controller. +- #interrupt-cells: Should be two. +- gpio-controller: Marks the device node as a GPIO controller. +- #gpio-cells : Should be two. + The first cell is the gpio pin number and the + second cell is used for optional parameters. + +Please refer to ../gpio/gpio.txt and ../interrupt-controller/interrupts.txt for +a general description of GPIO and interrupt bindings. + +Please refer to pinctrl-bindings.txt in this directory for details of the +common pinctrl bindings used by client devices, including the meaning of the +phrase "pin configuration node". + +The pin configuration nodes act as a container for an abitrary number of +subnodes. Each of these subnodes represents some desired configuration for a +pin, a group, or a list of pins or groups. This configuration can include the +mux function to select on those pin(s)/group(s), and various pin configuration +parameters, such as pull-up, drive strength, etc. + +The name of each subnode is not important; all subnodes should be enumerated +and processed purely based on their content. + +Each subnode only affects those parameters that are explicitly listed. In +other words, a subnode that lists a mux function but no pin configuration +parameters implies no information about any pin configuration parameters. +Similarly, a pin subnode that describes a pullup parameter implies no +information about e.g. the mux function. + + +The following generic properties as defined in pinctrl-bindings.txt are valid +to specify in a pin configuration subnode: + pins, function, bias-disable, bias-pull-down, bias-pull,up, drive-strength. + +Non-empty subnodes must specify the 'pins' property. +Note that not all properties are valid for all pins. + + +Valid values for qcom,pins are: + gpio0-gpio99 + Supports mux, bias and drive-strength + +Valid values for qcom,function are: +gpio, blsp_uart1, blsp_i2c0, blsp_i2c1, blsp_uart0, blsp_spi1, blsp_spi0 + +Example: + + tlmm: pinctrl@1000000 { + compatible = "qcom,ipq4019-pinctrl"; + reg = <0x1000000 0x300000>; + + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <0 208 0>; + + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt index 0cd701b1947f..c68b9554561f 100644 --- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt @@ -22,7 +22,7 @@ Required properties for iomux controller: - compatible: one of "rockchip,rk2928-pinctrl", "rockchip,rk3066a-pinctrl" "rockchip,rk3066b-pinctrl", "rockchip,rk3188-pinctrl" "rockchip,rk3228-pinctrl", "rockchip,rk3288-pinctrl" - "rockchip,rk3368-pinctrl" + "rockchip,rk3368-pinctrl", "rockchip,rk3399-pinctrl" - rockchip,grf: phandle referencing a syscon providing the "general register files" diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt new file mode 100644 index 000000000000..7b4800cc251e --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt @@ -0,0 +1,126 @@ +* STM32 GPIO and Pin Mux/Config controller + +STMicroelectronics's STM32 MCUs intregrate a GPIO and Pin mux/config hardware +controller. It controls the input/output settings on the available pins and +also provides ability to multiplex and configure the output of various on-chip +controllers onto these pads. + +Pin controller node: +Required properies: + - compatible: value should be one of the following: + (a) "st,stm32f429-pinctrl" + - #address-cells: The value of this property must be 1 + - #size-cells : The value of this property must be 1 + - ranges : defines mapping between pin controller node (parent) to + gpio-bank node (children). + - pins-are-numbered: Specify the subnodes are using numbered pinmux to + specify pins. + +GPIO controller/bank node: +Required properties: + - gpio-controller : Indicates this device is a GPIO controller + - #gpio-cells : Should be two. + The first cell is the pin number + The second one is the polarity: + - 0 for active high + - 1 for active low + - reg : The gpio address range, relative to the pinctrl range + - clocks : clock that drives this bank + - st,bank-name : Should be a name string for this bank as specified in + the datasheet + +Optional properties: + - reset: : Reference to the reset controller + +Example: +#include <dt-bindings/pinctrl/stm32f429-pinfunc.h> +... + + pin-controller { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,stm32f429-pinctrl"; + ranges = <0 0x40020000 0x3000>; + pins-are-numbered; + + gpioa: gpio@40020000 { + gpio-controller; + #gpio-cells = <2>; + reg = <0x0 0x400>; + resets = <&reset_ahb1 0>; + st,bank-name = "GPIOA"; + }; + ... + pin-functions nodes follow... + }; + +Contents of function subnode node: +---------------------------------- +Subnode format +A pinctrl node should contain at least one subnode representing the +pinctrl group available on the machine. Each subnode will list the +pins it needs, and how they should be configured, with regard to muxer +configuration, pullups, drive, output high/low and output speed. + + node { + pinmux = <PIN_NUMBER_PINMUX>; + GENERIC_PINCONFIG; + }; + +Required properties: +- pinmux: integer array, represents gpio pin number and mux setting. + Supported pin number and mux varies for different SoCs, and are defined in + dt-bindings/pinctrl/<soc>-pinfunc.h directly. + These defines are calculated as: + ((port * 16 + line) << 8) | function + With: + - port: The gpio port index (PA = 0, PB = 1, ..., PK = 11) + - line: The line offset within the port (PA0 = 0, PA1 = 1, ..., PA15 = 15) + - function: The function number, can be: + * 0 : GPIO + * 1 : Alternate Function 0 + * 2 : Alternate Function 1 + * 3 : Alternate Function 2 + * ... + * 16 : Alternate Function 15 + * 17 : Analog + +Optional properties: +- GENERIC_PINCONFIG: is the generic pinconfig options to use. + Available options are: + - bias-disable, + - bias-pull-down, + - bias-pull-up, + - drive-push-pull, + - drive-open-drain, + - output-low + - output-high + - slew-rate = <x>, with x being: + < 0 > : Low speed + < 1 > : Medium speed + < 2 > : Fast speed + < 3 > : High speed + +Example: + +pin-controller { +... + usart1_pins_a: usart1@0 { + pins1 { + pinmux = <STM32F429_PA9_FUNC_USART1_TX>; + bias-disable; + drive-push-pull; + slew-rate = <0>; + }; + pins2 { + pinmux = <STM32F429_PA10_FUNC_USART1_RX>; + bias-disable; + }; + }; +}; + +&usart1 { + pinctrl-0 = <&usart1_pins_a>; + pinctrl-names = "default"; + status = "okay"; +}; diff --git a/Documentation/devicetree/bindings/power/act8945a-charger.txt b/Documentation/devicetree/bindings/power/act8945a-charger.txt new file mode 100644 index 000000000000..bea254c9d136 --- /dev/null +++ b/Documentation/devicetree/bindings/power/act8945a-charger.txt @@ -0,0 +1,35 @@ +Device-Tree bindings for charger of Active-semi ACT8945A Multi-Function Device + +Required properties: + - compatible: "active-semi,act8945a", please refer to ../mfd/act8945a.txt. + - active-semi,chglev-gpios: charge current level phandle with args + as described in ../gpio/gpio.txt. + +Optional properties: + - active-semi,check-battery-temperature: boolean to check the battery + temperature or not. + - active-semi,input-voltage-threshold-microvolt: unit: mV; + Specifies the charger's input over-voltage threshold value; + The value can be: 6600, 7000, 7500, 8000; default: 6600 + - active-semi,precondition-timeout: unit: minutes; + Specifies the charger's PRECONDITION safety timer setting value; + The value can be: 40, 60, 80, 0; If 0, it means to disable this timer; + default: 40. + - active-semi,total-timeout: unit: hours; + Specifies the charger's total safety timer setting value; + The value can be: 3, 4, 5, 0; If 0, it means to disable this timer; + default: 3. + +Example: + pmic@5b { + compatible = "active-semi,act8945a"; + reg = <0x5b>; + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_charger_chglev>; + active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>; + active-semi,input-voltage-threshold-microvolt = <6600>; + active-semi,precondition-timeout = <40>; + active-semi,total-timeout = <3>; + }; diff --git a/Documentation/devicetree/bindings/power_supply/ti,bq24735.txt b/Documentation/devicetree/bindings/power_supply/ti,bq24735.txt index 4f6a550184d0..3bf55757ceec 100644 --- a/Documentation/devicetree/bindings/power_supply/ti,bq24735.txt +++ b/Documentation/devicetree/bindings/power_supply/ti,bq24735.txt @@ -22,6 +22,9 @@ Optional properties : value must be between 128mA and 8.064A with a 128mA step resolution. The POR value is 0x1000h. This number is in mA (e.g. 8064), see the spec for more information about the InputCurrent (0x3fh) register. + - ti,external-control : Indicates that the charger is configured externally + and that the host should not attempt to enable/disable charging or set the + charge voltage/current. Example: diff --git a/Documentation/devicetree/bindings/regmap/regmap.txt b/Documentation/devicetree/bindings/regmap/regmap.txt index b494f8b8ef72..e98a9652ccc8 100644 --- a/Documentation/devicetree/bindings/regmap/regmap.txt +++ b/Documentation/devicetree/bindings/regmap/regmap.txt @@ -5,15 +5,18 @@ Index Device Endianness properties --------------------------------------------------- 1 BE 'big-endian' 2 LE 'little-endian' +3 Native 'native-endian' For one device driver, which will run in different scenarios above on different SoCs using the devicetree, we need one way to simplify this. -Required properties: -- {big,little}-endian: these are boolean properties, if absent - meaning that the CPU and the Device are in the same endianness mode, - these properties are for register values and all the buffers only. +Optional properties: +- {big,little,native}-endian: these are boolean properties, if absent + then the implementation will choose a default based on the device + being controlled. These properties are for register values and all + the buffers only. Native endian means that the CPU and device have + the same endianness. Examples: Scenario 1 : CPU in LE mode & device in LE mode. diff --git a/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt b/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt new file mode 100644 index 000000000000..5c80a7779552 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/act8945a-regulator.txt @@ -0,0 +1,80 @@ +Device-Tree bindings for regulators of Active-semi ACT8945A Multi-Function Device + +Required properties: + - compatible: "active-semi,act8945a", please refer to ../mfd/act8945a.txt. + +Optional properties: +- active-semi,vsel-high: Indicates if the VSEL pin is set to logic-high. + If this property is missing, assume the VSEL pin is set to logic-low. + +Optional input supply properties: + - vp1-supply: The input supply for REG_DCDC1 + - vp2-supply: The input supply for REG_DCDC2 + - vp3-supply: The input supply for REG_DCDC3 + - inl45-supply: The input supply for REG_LDO1 and REG_LDO2 + - inl67-supply: The input supply for REG_LDO3 and REG_LDO4 + +Any standard regulator properties can be used to configure the single regulator. + +The valid names for regulators are: + REG_DCDC1, REG_DCDC2, REG_DCDC3, REG_LDO1, REG_LDO2, REG_LDO3, REG_LDO4. + +Example: + pmic@5b { + compatible = "active-semi,act8945a"; + reg = <0x5b>; + status = "okay"; + + active-semi,vsel-high; + + regulators { + vdd_1v35_reg: REG_DCDC1 { + regulator-name = "VDD_1V35"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + vdd_1v2_reg: REG_DCDC2 { + regulator-name = "VDD_1V2"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + }; + + vdd_3v3_reg: REG_DCDC3 { + regulator-name = "VDD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_fuse_reg: REG_LDO1 { + regulator-name = "VDD_FUSE"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + vdd_3v3_lp_reg: REG_LDO2 { + regulator-name = "VDD_3V3_LP"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_led_reg: REG_LDO3 { + regulator-name = "VDD_LED"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd_sdhc_1v8_reg: REG_LDO4 { + regulator-name = "VDD_SDHC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt b/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt new file mode 100644 index 000000000000..14cfdc564159 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/hisilicon,hi655x-regulator.txt @@ -0,0 +1,29 @@ +Hisilicon Hi655x Voltage regulators + +Note: +The Hi655x regulator control is managed by Hi655x PMIC. +So the node of this regulator must be child node of Hi655x +PMIC node. + +The driver uses the regulator core framework, so please also +take the bindings of regulator.txt for reference. + +The valid names for regulators are: + +LDO2_2V8 LDO7_SDIO LDO10_2V85 LDO13_1V8 LDO14_2V8 +LDO15_1V8 LDO17_2V5 LDO19_3V0 LDO21_1V8 LDO22_1V2 + +Example: + pmic: pmic@f8000000 { + compatible = "hisilicon,hi655x-pmic"; + ... + regulators { + ldo2: LDO2@a21 { + regulator-name = "LDO2_2V8"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3200000>; + regulator-enable-ramp-delay = <120>; + }; + ... + } + } diff --git a/Documentation/devicetree/bindings/regulator/lp872x.txt b/Documentation/devicetree/bindings/regulator/lp872x.txt index 78183182dad9..ca58a68ffdf1 100644 --- a/Documentation/devicetree/bindings/regulator/lp872x.txt +++ b/Documentation/devicetree/bindings/regulator/lp872x.txt @@ -28,6 +28,7 @@ Optional properties: - ti,dvs-gpio: GPIO specifier for external DVS pin control of LP872x devices. - ti,dvs-vsel: DVS selector. 0 = SEL_V1, 1 = SEL_V2. - ti,dvs-state: initial DVS pin state. 0 = DVS_LOW, 1 = DVS_HIGH. + - enable-gpios: GPIO specifier for EN pin control of LP872x devices. Sub nodes for regulator_init_data LP8720 has maximum 6 nodes. (child name: ldo1 ~ 5 and buck) diff --git a/Documentation/devicetree/bindings/regulator/max77802.txt b/Documentation/devicetree/bindings/regulator/max77802.txt index 09d796ed48be..879e98d3b9aa 100644 --- a/Documentation/devicetree/bindings/regulator/max77802.txt +++ b/Documentation/devicetree/bindings/regulator/max77802.txt @@ -60,7 +60,7 @@ The possible values for "regulator-initial-mode" and "regulator-mode" are: 1: Normal regulator voltage output mode. 3: Low Power which reduces the quiescent current down to only 1uA -The list of valid modes are defined in the dt-bindings/clock/maxim,max77802.h +The valid modes list is defined in the dt-bindings/regulator/maxim,max77802.h header and can be included by device tree source files. The standard "regulator-mode" property can only be used for regulators that diff --git a/Documentation/devicetree/bindings/regulator/regulator-max77620.txt b/Documentation/devicetree/bindings/regulator/regulator-max77620.txt new file mode 100644 index 000000000000..b3c8ca672024 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/regulator-max77620.txt @@ -0,0 +1,200 @@ +Regulator DT binding for MAX77620 Power management IC from Maxim Semiconductor. + +Device has multiple DCDC(sd[0-3] and LDOs(ldo[0-8]). The input supply +of these regulators are defined under parent device node. +Details of regulator properties are defined as child node under +sub-node "regulators" which is child node of device node. + +Please refer file <Documentation/devicetree/bindings/regulator/regulator.txt> +for common regulator bindings used by client. + +Following are properties of parent node related to regulators. + +Optional properties: +------------------- +The input supply of regulators are the optional properties on the +parent device node. The input supply of these regulators are provided +through following properties: +in-sd0-supply: Input supply for SD0, INA-SD0 or INB-SD0 pins. +in-sd1-supply: Input supply for SD1. +in-sd2-supply: Input supply for SD2. +in-sd3-supply: Input supply for SD3. +in-ldo0-1-supply: Input supply for LDO0 and LDO1. +in-ldo2-supply: Input supply for LDO2. +in-ldo3-5-supply: Input supply for LDO3 and LDO5 +in-ldo4-6-supply: Input supply for LDO4 and LDO6. +in-ldo7-8-supply: Input supply for LDO7 and LDO8. + +Optional sub nodes for regulators under "regulators" subnode: +------------------------------------------------------------ +The subnodes name is the name of regulator and it must be one of: + sd[0-3], ldo[0-8] + +Each sub-node should contain the constraints and initialization +information for that regulator. The definition for each of these +nodes is defined using the standard binding for regulators found at +<Documentation/devicetree/bindings/regulator/regulator.txt>. + +Theres are also additional properties for SD/LDOs. These additional properties +are required to configure FPS configuration parameters for SDs and LDOs. +Please refer <devicetree/bindings/mfd/max77620.txt> for more detail of Flexible +Power Sequence (FPS). +Following are additional properties: + +- maxim,active-fps-source: FPS source for the regulators to get + enabled/disabled when system is in + active state. Valid values are: + - MAX77620_FPS_SRC_0, + FPS source is FPS0. + - MAX77620_FPS_SRC_1, + FPS source is FPS1 + - MAX77620_FPS_SRC_2 and + FPS source is FPS2 + - MAX77620_FPS_SRC_NONE. + Regulator is not controlled + by FPS events and it gets + enabled/disabled by register + access. + Absence of this property will leave + the FPS configuration register for that + regulator to default configuration. + +- maxim,active-fps-power-up-slot: Sequencing event slot number on which + the regulator get enabled when + master FPS input event set to HIGH. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,active-fps-power-down-slot: Sequencing event slot number on which + the regulator get disabled when master + FPS input event set to LOW. + Valid values are 0 to 7. + This is applicable if FPS source is + selected as FPS0, FPS1 or FPS2. + +- maxim,suspend-fps-source: This is same as property + "maxim,active-fps-source" but value + get configured when system enters in + to suspend state. + +- maxim,suspend-fps-power-up-slot: This is same as property + "maxim,active-fps-power-up-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + +- maxim,suspend-fps-power-down-slot: This is same as property + "maxim,active-fps-power-down-slot" but + this value get configured into FPS + configuration register when system + enters into suspend. + This is applicable if suspend state + FPS source is selected as FPS0, FPS1 or + FPS2. + +Example: +-------- +#include <dt-bindings/mfd/max77620.h> +... +max77620@3c { + in-ldo0-1-supply = <&max77620_sd2>; + in-ldo7-8-supply = <&max77620_sd2>; + regulators { + sd0 { + regulator-name = "vdd-core"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1400000>; + regulator-boot-on; + regulator-always-on; + maxim,active-fps-source = <MAX77620_FPS_SRC_1>; + }; + + sd1 { + regulator-name = "vddio-ddr"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + maxim,active-fps-source = <MAX77620_FPS_SRC_0>; + }; + + sd2 { + regulator-name = "vdd-pre-reg"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + }; + + sd3 { + regulator-name = "vdd-1v8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo0 { + regulator-name = "avdd-sys"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo1 { + regulator-name = "vdd-pex"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + }; + + ldo2 { + regulator-name = "vddio-sdmmc3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + ldo3 { + regulator-name = "vdd-cam-hv"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo4 { + regulator-name = "vdd-rtc"; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1250000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo5 { + regulator-name = "avdd-ts-hv"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + ldo6 { + regulator-name = "vdd-ts"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo7 { + regulator-name = "vdd-gen-pll-edp"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo8 { + regulator-name = "vdd-hdmi-dp"; + regulator-min-microvolt = <1050000>; + regulator-max-microvolt = <1050000>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt index 1d112fc456aa..ecfc593cac15 100644 --- a/Documentation/devicetree/bindings/regulator/regulator.txt +++ b/Documentation/devicetree/bindings/regulator/regulator.txt @@ -44,6 +44,11 @@ Optional properties: any consumer request. - regulator-pull-down: Enable pull down resistor when the regulator is disabled. - regulator-over-current-protection: Enable over current protection. +- regulator-active-discharge: tristate, enable/disable active discharge of + regulators. The values are: + 0: Disable active discharge. + 1: Enable active discharge. + Absence of this property will leave configuration to default. Deprecated properties: - regulator-compatible: If a regulator chip contains multiple diff --git a/Documentation/devicetree/bindings/remoteproc/st-rproc.txt b/Documentation/devicetree/bindings/remoteproc/st-rproc.txt new file mode 100644 index 000000000000..1031bcd90a79 --- /dev/null +++ b/Documentation/devicetree/bindings/remoteproc/st-rproc.txt @@ -0,0 +1,41 @@ +STMicroelectronics Co-Processor Bindings +---------------------------------------- + +This binding provides support for adjunct processors found on ST SoCs. + +Co-processors can be controlled from the bootloader or the primary OS. If +the bootloader starts a co-processor, the primary OS must detect its state +and act accordingly. + +Required properties: +- compatible Should be one of: + "st,st231-rproc" + "st,st40-rproc" +- memory-region Reserved memory (See: ../reserved-memory/reserved-memory.txt) +- resets Reset lines (See: ../reset/reset.txt) +- reset-names Must be "sw_reset" and "pwr_reset" +- clocks Clock for co-processor (See: ../clock/clock-bindings.txt) +- clock-frequency Clock frequency to set co-processor at if the bootloader + hasn't already done so +- st,syscfg System configuration register which holds the boot vector + for the co-processor + 1st cell: Phandle to syscon block + 2nd cell: Boot vector register offset + +Example: + + audio_reserved: rproc@42000000 { + compatible = "shared-dma-pool"; + reg = <0x42000000 0x01000000>; + no-map; + }; + + st231-audio { + compatible = "st,st231-rproc"; + memory-region = <&audio_reserved>; + resets = <&softreset STIH407_ST231_AUD_SOFTRESET>; + reset-names = "sw_reset"; + clocks = <&clk_s_c0_flexgen CLK_ST231_AUD_0>; + clock-frequency = <600000000>; + st,syscfg = <&syscfg_core 0x228>; + }; diff --git a/Documentation/devicetree/bindings/rng/brcm,bcm6368.txt b/Documentation/devicetree/bindings/rng/brcm,bcm6368.txt new file mode 100644 index 000000000000..4b5ac600bfbd --- /dev/null +++ b/Documentation/devicetree/bindings/rng/brcm,bcm6368.txt @@ -0,0 +1,17 @@ +BCM6368 Random number generator + +Required properties: + +- compatible : should be "brcm,bcm6368-rng" +- reg : Specifies base physical address and size of the registers +- clocks : phandle to clock-controller plus clock-specifier pair +- clock-names : "ipsec" as a clock name + +Example: + random: rng@10004180 { + compatible = "brcm,bcm6368-rng"; + reg = <0x10004180 0x14>; + + clocks = <&periph_clk 18>; + clock-names = "ipsec"; + }; diff --git a/Documentation/devicetree/bindings/rng/microchip,pic32-rng.txt b/Documentation/devicetree/bindings/rng/microchip,pic32-rng.txt new file mode 100644 index 000000000000..c6d1003befb7 --- /dev/null +++ b/Documentation/devicetree/bindings/rng/microchip,pic32-rng.txt @@ -0,0 +1,17 @@ +* Microchip PIC32 Random Number Generator + +The PIC32 RNG provides a pseudo random number generator which can be seeded by +another true random number generator. + +Required properties: +- compatible : should be "microchip,pic32mzda-rng" +- reg : Specifies base physical address and size of the registers. +- clocks: clock phandle. + +Example: + + rng: rng@1f8e6000 { + compatible = "microchip,pic32mzda-rng"; + reg = <0x1f8e6000 0x1000>; + clocks = <&PBCLK5>; + }; diff --git a/Documentation/devicetree/bindings/rtc/alphascale,asm9260-rtc.txt b/Documentation/devicetree/bindings/rtc/alphascale,asm9260-rtc.txt new file mode 100644 index 000000000000..76ebca568db9 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/alphascale,asm9260-rtc.txt @@ -0,0 +1,19 @@ +* Alphascale asm9260 SoC Real Time Clock + +Required properties: +- compatible: Should be "alphascale,asm9260-rtc" +- reg: Physical base address of the controller and length + of memory mapped region. +- interrupts: IRQ line for the RTC. +- clocks: Reference to the clock entry. +- clock-names: should contain: + * "ahb" for the SoC RTC clock + +Example: +rtc0: rtc@800a0000 { + compatible = "alphascale,asm9260-rtc"; + reg = <0x800a0000 0x100>; + clocks = <&acc CLKID_AHB_RTC>; + clock-names = "ahb"; + interrupts = <2>; +}; diff --git a/Documentation/devicetree/bindings/rtc/epson,rx6110.txt b/Documentation/devicetree/bindings/rtc/epson,rx6110.txt new file mode 100644 index 000000000000..3dc313e01f77 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/epson,rx6110.txt @@ -0,0 +1,39 @@ +Epson RX6110 Real Time Clock +============================ + +The Epson RX6110 can be used with SPI or I2C busses. The kind of +bus depends on the SPISEL pin and can not be configured via software. + +I2C mode +-------- + +Required properties: + - compatible: should be: "epson,rx6110" + - reg : the I2C address of the device for I2C + +Example: + + rtc: rtc@32 { + compatible = "epson,rx6110" + reg = <0x32>; + }; + +SPI mode +-------- + +Required properties: + - compatible: should be: "epson,rx6110" + - reg: chip select number + - spi-cs-high: RX6110 needs chipselect high + - spi-cpha: RX6110 works with SPI shifted clock phase + - spi-cpol: RX6110 works with SPI inverse clock polarity + +Example: + + rtc: rtc@3 { + compatible = "epson,rx6110" + reg = <3> + spi-cs-high; + spi-cpha; + spi-cpol; + }; diff --git a/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt b/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt new file mode 100644 index 000000000000..ddef330d2709 --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/maxim,ds3231.txt @@ -0,0 +1,37 @@ +* Maxim DS3231 Real Time Clock + +Required properties: +see: Documentation/devicetree/bindings/i2c/trivial-devices.txt + +Optional property: +- #clock-cells: Should be 1. +- clock-output-names: + overwrite the default clock names "ds3231_clk_sqw" and "ds3231_clk_32khz". + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. Following indices are allowed: + - 0: square-wave output on the SQW pin + - 1: square-wave output on the 32kHz pin + +- interrupts: rtc alarm/event interrupt. When this property is selected, + clock on the SQW pin cannot be used. + +Example: + +ds3231: ds3231@51 { + compatible = "maxim,ds3231"; + reg = <0x68>; + #clock-cells = <1>; +}; + +device1 { +... + clocks = <&ds3231 0>; +... +}; + +device2 { +... + clocks = <&ds3231 1>; +... +}; diff --git a/Documentation/devicetree/bindings/rtc/microchip,pic32-rtc.txt b/Documentation/devicetree/bindings/rtc/microchip,pic32-rtc.txt new file mode 100644 index 000000000000..180b7144bfcc --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/microchip,pic32-rtc.txt @@ -0,0 +1,21 @@ +* Microchip PIC32 Real Time Clock and Calendar + +The RTCC keeps time in hours, minutes, and seconds, and one half second. It +provides a calendar in weekday, date, month, and year. It also provides a +configurable alarm. + +Required properties: +- compatible: should be: "microchip,pic32mzda-rtc" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: RTC alarm/event interrupt +- clocks: clock phandle + +Example: + + rtc: rtc@1f8c0000 { + compatible = "microchip,pic32mzda-rtc"; + reg = <0x1f8c0000 0x60>; + interrupts = <166 IRQ_TYPE_EDGE_RISING>; + clocks = <&PBCLK6>; + }; diff --git a/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt index f67e761bcc18..bf2411f366e5 100644 --- a/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt +++ b/Documentation/devicetree/bindings/scsi/hisilicon-sas.txt @@ -5,6 +5,7 @@ The HiSilicon SAS controller supports SAS/SATA. Main node required properties: - compatible : value should be as follows: (a) "hisilicon,hip05-sas-v1" for v1 hw in hip05 chipset + (b) "hisilicon,hip06-sas-v2" for v2 hw in hip06 chipset - sas-addr : array of 8 bytes for host SAS address - reg : Address and length of the SAS register - hisilicon,sas-syscon: phandle of syscon used for sas control @@ -13,7 +14,7 @@ Main node required properties: - ctrl-clock-ena-reg : offset to controller clock enable register in ctrl reg - queue-count : number of delivery and completion queues in the controller - phy-count : number of phys accessible by the controller - - interrupts : Interrupts for phys, completion queues, and fatal + - interrupts : For v1 hw: Interrupts for phys, completion queues, and fatal sources; the interrupts are ordered in 3 groups, as follows: - Phy interrupts - Completion queue interrupts @@ -30,6 +31,24 @@ Main node required properties: Fatal interrupts : the fatal interrupts are ordered as follows: - ECC - AXI bus + For v2 hw: Interrupts for phys, Sata, and completion queues; + the interrupts are ordered in 3 groups, as follows: + - Phy interrupts + - Sata interrupts + - Completion queue interrupts + Phy interrupts : Each controller has 2 phy interrupts: + - phy up/down + - channel interrupt + Sata interrupts : Each phy on the controller has 1 Sata + interrupt. The interrupts are ordered in increasing + order. + Completion queue interrupts : each completion queue has 1 + interrupt source. The interrupts are ordered in + increasing order. + +Optional main node properties: + - hip06-sas-v2-quirk-amt : when set, indicates that the v2 controller has the + "am-max-transmissions" limitation. Example: sas0: sas@c1000000 { diff --git a/Documentation/devicetree/bindings/serial/brcm,bcm2835-aux-uart.txt b/Documentation/devicetree/bindings/serial/brcm,bcm2835-aux-uart.txt new file mode 100644 index 000000000000..b5cc6297cd1b --- /dev/null +++ b/Documentation/devicetree/bindings/serial/brcm,bcm2835-aux-uart.txt @@ -0,0 +1,18 @@ +* BCM2835 AUXILIAR UART + +Required properties: + +- compatible: "brcm,bcm2835-aux-uart" +- reg: The base address of the UART register bank. +- interrupts: A single interrupt specifier. +- clocks: Clock driving the hardware; used to figure out the baud rate + divisor. + +Example: + + uart1: serial@7e215040 { + compatible = "brcm,bcm2835-aux-uart"; + reg = <0x7e215040 0x40>; + interrupts = <1 29>; + clocks = <&aux BCM2835_AUX_CLOCK_UART>; + }; diff --git a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt index 401b1b33c2c4..528c3b90f23c 100644 --- a/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt +++ b/Documentation/devicetree/bindings/serial/renesas,sci-serial.txt @@ -19,6 +19,8 @@ Required properties: - "renesas,scifa-r8a7791" for R8A7791 (R-Car M2-W) SCIFA compatible UART. - "renesas,scifb-r8a7791" for R8A7791 (R-Car M2-W) SCIFB compatible UART. - "renesas,hscif-r8a7791" for R8A7791 (R-Car M2-W) HSCIF compatible UART. + - "renesas,scif-r8a7792" for R8A7792 (R-Car V2H) SCIF compatible UART. + - "renesas,hscif-r8a7792" for R8A7792 (R-Car V2H) HSCIF compatible UART. - "renesas,scif-r8a7793" for R8A7793 (R-Car M2-N) SCIF compatible UART. - "renesas,scifa-r8a7793" for R8A7793 (R-Car M2-N) SCIFA compatible UART. - "renesas,scifb-r8a7793" for R8A7793 (R-Car M2-N) SCIFB compatible UART. diff --git a/Documentation/devicetree/bindings/sound/cs4271.txt b/Documentation/devicetree/bindings/sound/cs4271.txt index e2cd1d7539e5..6e699ceabacd 100644 --- a/Documentation/devicetree/bindings/sound/cs4271.txt +++ b/Documentation/devicetree/bindings/sound/cs4271.txt @@ -33,12 +33,19 @@ Optional properties: Note that this is not needed in case the clocks are stable throughout the entire runtime of the codec. + - vd-supply: Digital power + - vl-supply: Logic power + - va-supply: Analog Power + Examples: codec_i2c: cs4271@10 { compatible = "cirrus,cs4271"; reg = <0x10>; reset-gpio = <&gpio 23 0>; + vd-supply = <&vdd_3v3_reg>; + vl-supply = <&vdd_3v3_reg>; + va-supply = <&vdd_3v3_reg>; }; codec_spi: cs4271@0 { diff --git a/Documentation/devicetree/bindings/sparc_sun_oracle_rng.txt b/Documentation/devicetree/bindings/sparc_sun_oracle_rng.txt new file mode 100644 index 000000000000..b0b211194c71 --- /dev/null +++ b/Documentation/devicetree/bindings/sparc_sun_oracle_rng.txt @@ -0,0 +1,30 @@ +HWRNG support for the n2_rng driver + +Required properties: +- reg : base address to sample from +- compatible : should contain one of the following + RNG versions: + - 'SUNW,n2-rng' for Niagara 2 Platform (SUN UltraSPARC T2 CPU) + - 'SUNW,vf-rng' for Victoria Falls Platform (SUN UltraSPARC T2 Plus CPU) + - 'SUNW,kt-rng' for Rainbow/Yosemite Falls Platform (SUN SPARC T3/T4), (UltraSPARC KT/Niagara 3 - development names) + more recent systems (after Oracle acquisition of SUN) + - 'ORCL,m4-rng' for SPARC T5/M5 + - 'ORCL,m7-rng' for SPARC T7/M7 + +Examples: +/* linux LDOM on SPARC T5-2 */ +Node 0xf029a4f4 + .node: f029a4f4 + rng-#units: 00000002 + compatible: 'ORCL,m4-rng' + reg: 0000000e + name: 'random-number-generator' + +/* solaris on SPARC M7-8 */ +Node 0xf028c08c + rng-#units: 00000003 + compatible: 'ORCL,m7-rng' + reg: 0000000e + name: 'random-number-generator' + +PS: see as well prtconfs.git by DaveM diff --git a/Documentation/devicetree/bindings/spi/adi,axi-spi-engine.txt b/Documentation/devicetree/bindings/spi/adi,axi-spi-engine.txt new file mode 100644 index 000000000000..8a18d71e6879 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/adi,axi-spi-engine.txt @@ -0,0 +1,31 @@ +Analog Devices AXI SPI Engine controller Device Tree Bindings + +Required properties: +- compatible : Must be "adi,axi-spi-engine-1.00.a"" +- reg : Physical base address and size of the register map. +- interrupts : Property with a value describing the interrupt + number. +- clock-names : List of input clock names - "s_axi_aclk", "spi_clk" +- clocks : Clock phandles and specifiers (See clock bindings for + details on clock-names and clocks). +- #address-cells : Must be <1> +- #size-cells : Must be <0> + +Optional subnodes: + Subnodes are use to represent the SPI slave devices connected to the SPI + master. They follow the generic SPI bindings as outlined in spi-bus.txt. + +Example: + + spi@@44a00000 { + compatible = "adi,axi-spi-engine-1.00.a"; + reg = <0x44a00000 0x1000>; + interrupts = <0 56 4>; + clocks = <&clkc 15 &clkc 15>; + clock-names = "s_axi_aclk", "spi_clk"; + + #address-cells = <1>; + #size-cells = <0>; + + /* SPI devices */ + }; diff --git a/Documentation/devicetree/bindings/spi/icpdas-lp8841-spi-rtc.txt b/Documentation/devicetree/bindings/spi/icpdas-lp8841-spi-rtc.txt new file mode 100644 index 000000000000..852b651f3bc5 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/icpdas-lp8841-spi-rtc.txt @@ -0,0 +1,54 @@ +* ICP DAS LP-8841 SPI Controller for RTC + +ICP DAS LP-8841 contains a DS-1302 RTC. RTC is connected to an IO +memory register, which acts as an SPI master device. + +The device uses the standard MicroWire half-duplex transfer timing. +Master output is set on low clock and sensed by the RTC on the rising +edge. Master input is set by the RTC on the trailing edge and is sensed +by the master on low clock. + +Required properties: + +- #address-cells: should be 1 + +- #size-cells: should be 0 + +- compatible: should be "icpdas,lp8841-spi-rtc" + +- reg: should provide IO memory address + +Requirements to SPI slave nodes: + +- There can be only one slave device. + +- The spi slave node should claim the following flags which are + required by the spi controller. + + - spi-3wire: The master itself has only 3 wire. It cannor work in + full duplex mode. + + - spi-cs-high: DS-1302 has active high chip select line. The master + doesn't support active low. + + - spi-lsb-first: DS-1302 requires least significant bit first + transfers. The master only support this type of bit ordering. + + +Example: + +spi@901c { + #address-cells = <1>; + #size-cells = <0>; + compatible = "icpdas,lp8841-spi-rtc"; + reg = <0x901c 0x1>; + + rtc@0 { + compatible = "maxim,ds1302"; + reg = <0>; + spi-max-frequency = <500000>; + spi-3wire; + spi-lsb-first; + spi-cs-high; + }; +}; diff --git a/Documentation/devicetree/bindings/spi/spi-rockchip.txt b/Documentation/devicetree/bindings/spi/spi-rockchip.txt index 0c491bda4c65..1b14d69d8903 100644 --- a/Documentation/devicetree/bindings/spi/spi-rockchip.txt +++ b/Documentation/devicetree/bindings/spi/spi-rockchip.txt @@ -9,6 +9,7 @@ Required Properties: "rockchip,rk3066-spi" for rk3066. "rockchip,rk3188-spi", "rockchip,rk3066-spi" for rk3188. "rockchip,rk3288-spi", "rockchip,rk3066-spi" for rk3288. + "rockchip,rk3399-spi", "rockchip,rk3066-spi" for rk3399. - reg: physical base address of the controller and length of memory mapped region. - interrupts: The interrupt number to the cpu. The interrupt specifier format diff --git a/Documentation/devicetree/bindings/spi/spi-xilinx.txt b/Documentation/devicetree/bindings/spi/spi-xilinx.txt new file mode 100644 index 000000000000..c7b7856bd528 --- /dev/null +++ b/Documentation/devicetree/bindings/spi/spi-xilinx.txt @@ -0,0 +1,22 @@ +Xilinx SPI controller Device Tree Bindings +------------------------------------------------- + +Required properties: +- compatible : Should be "xlnx,xps-spi-2.00.a" or "xlnx,xps-spi-2.00.b" +- reg : Physical base address and size of SPI registers map. +- interrupts : Property with a value describing the interrupt + number. +- interrupt-parent : Must be core interrupt controller + +Optional properties: +- xlnx,num-ss-bits : Number of chip selects used. + +Example: + axi_quad_spi@41e00000 { + compatible = "xlnx,xps-spi-2.00.a"; + interrupt-parent = <&intc>; + interrupts = <0 31 1>; + reg = <0x41e00000 0x10000>; + xlnx,num-ss-bits = <0x1>; + }; + diff --git a/Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt b/Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt new file mode 100644 index 000000000000..6087defd9f93 --- /dev/null +++ b/Documentation/devicetree/bindings/tty/serial/mvebu-uart.txt @@ -0,0 +1,13 @@ +* Marvell UART : Non standard UART used in some of Marvell EBU SoCs (e.g., Armada-3700) + +Required properties: +- compatible: "marvell,armada-3700-uart" +- reg: offset and length of the register set for the device. +- interrupts: device interrupt + +Example: + serial@12000 { + compatible = "marvell,armada-3700-uart"; + reg = <0x12000 0x400>; + interrupts = <43>; + }; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 781296bfbe4f..1084e2bcbe1c 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -2,7 +2,14 @@ Required properties: - compatible: should be one of: + "fsl,imx23-usb" "fsl,imx27-usb" + "fsl,imx28-usb" + "fsl,imx6q-usb" + "fsl,imx6sl-usb" + "fsl,imx6sx-usb" + "fsl,imx6ul-usb" + "fsl,imx7d-usb" "lsi,zevio-usb" "qcom,ci-hdrc" "chipidea,usb2" @@ -53,6 +60,22 @@ Optional properties: be specified. - phy-clkgate-delay-us: the delay time (us) between putting the PHY into low power mode and gating the PHY clock. +- non-zero-ttctrl-ttha: after setting this property, the value of register + ttctrl.ttha will be 0x7f; if not, the value will be 0x0, this is the default + value. It needs to be very carefully for setting this property, it is + recommended that consult with your IC engineer before setting this value. + On the most of chipidea platforms, the "usage_tt" flag at RTL is 0, so this + property only affects siTD. + If this property is not set, the max packet size is 1023 bytes, and if + the total of packet size for pervious transactions are more than 256 bytes, + it can't accept any transactions within this frame. The use case is single + transaction, but higher frame rate. + If this property is set, the max packet size is 188 bytes, it can handle + more transactions than above case, it can accept transactions until it + considers the left room size within frame is less than 188 bytes, software + needs to make sure it does not send more than 90% + maximum_periodic_data_per_frame. The use case is multiple transactions, but + less frame rate. i.mx specific properties - fsl,usbmisc: phandler of non-core register device, with one diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt index 221368207ca4..20a68bf2b4e7 100644 --- a/Documentation/devicetree/bindings/usb/dwc2.txt +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -8,6 +8,8 @@ Required properties: - rockchip,rk3066-usb: The DWC2 USB controller instance in the rk3066 Soc; - "rockchip,rk3188-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3188 Soc; - "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc; + - "lantiq,arx100-usb": The DWC2 USB controller instance in Lantiq ARX SoCs; + - "lantiq,xrx200-usb": The DWC2 USB controller instance in Lantiq XRX SoCs; - snps,dwc2: A generic DWC2 USB controller with default parameters. - reg : Should contain 1 register range (address and length) - interrupts : Should contain 1 interrupt diff --git a/Documentation/devicetree/bindings/usb/usb-device.txt b/Documentation/devicetree/bindings/usb/usb-device.txt new file mode 100644 index 000000000000..1c35e7b665e1 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-device.txt @@ -0,0 +1,28 @@ +Generic USB Device Properties + +Usually, we only use device tree for hard wired USB device. +The reference binding doc is from: +http://www.firmware.org/1275/bindings/usb/usb-1_0.ps + +Required properties: +- compatible: usbVID,PID. The textual representation of VID, PID shall + be in lower case hexadecimal with leading zeroes suppressed. The + other compatible strings from the above standard binding could also + be used, but a device adhering to this binding may leave out all except + for usbVID,PID. +- reg: the port number which this device is connecting to, the range + is 1-31. + +Example: + +&usb1 { + status = "okay"; + + #address-cells = <1>; + #size-cells = <0>; + + hub: genesys@1 { + compatible = "usb5e3,608"; + reg = <1>; + }; +} diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt index 082573289f1e..6a17aa85c4d5 100644 --- a/Documentation/devicetree/bindings/usb/usb-xhci.txt +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -1,10 +1,23 @@ USB xHCI controllers Required properties: - - compatible: should be one of "generic-xhci", - "marvell,armada-375-xhci", "marvell,armada-380-xhci", - "renesas,xhci-r8a7790", "renesas,xhci-r8a7791", "renesas,xhci-r8a7793", - "renesas,xhci-r8a7795" (deprecated: "xhci-platform"). + - compatible: should be one or more of + + - "generic-xhci" for generic XHCI device + - "marvell,armada-375-xhci" for Armada 375 SoCs + - "marvell,armada-380-xhci" for Armada 38x SoCs + - "renesas,xhci-r8a7790" for r8a7790 SoC + - "renesas,xhci-r8a7791" for r8a7791 SoC + - "renesas,xhci-r8a7793" for r8a7793 SoC + - "renesas,xhci-r8a7795" for r8a7795 SoC + - "renesas,rcar-gen2-xhci" for a generic R-Car Gen2 compatible device + - "renesas,rcar-gen3-xhci" for a generic R-Car Gen3 compatible device + - "xhci-platform" (deprecated) + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + - reg: should contain address and length of the standard XHCI register set for the device. - interrupts: one XHCI interrupt should be described here. diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 656f3dd31f19..bd33a268fd1b 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -120,6 +120,7 @@ intercontrol Inter Control Group invensense InvenSense Inc. isee ISEE 2007 S.L. isil Intersil +issi Integrated Silicon Solutions Inc. jedec JEDEC Solid State Technology Association karo Ka-Ro electronics GmbH keymile Keymile GmbH @@ -170,6 +171,7 @@ opencores OpenCores.org option Option NV ortustech Ortus Technology Co., Ltd. ovti OmniVision Technologies +ORCL Oracle Corporation panasonic Panasonic Corporation parade Parade Technologies Inc. pericom Pericom Technology Inc. @@ -204,6 +206,7 @@ seagate Seagate Technology PLC semtech Semtech Corporation sgx SGX Sensortech sharp Sharp Corporation +si-en Si-En Technology Ltd. sigma Sigma Designs, Inc. sil Silicon Image silabs Silicon Laboratories @@ -228,6 +231,7 @@ ste ST-Ericsson stericsson ST-Ericsson syna Synaptics Inc. synology Synology, Inc. +SUNW Sun Microsystems, Inc tbs TBS Technologies tcl Toby Churchill Ltd. technologic Technologic Systems |
