diff options
Diffstat (limited to 'Documentation/devicetree/bindings/serial')
12 files changed, 325 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/serial/arc-uart.txt b/Documentation/devicetree/bindings/serial/arc-uart.txt new file mode 100644 index 000000000000..5cae2eb686f8 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/arc-uart.txt @@ -0,0 +1,26 @@ +* Synopsys ARC UART : Non standard UART used in some of the ARC FPGA boards + +Required properties: +- compatible : "snps,arc-uart" +- reg : offset and length of the register set for the device. +- interrupts : device interrupt +- clock-frequency : the input clock frequency for the UART +- current-speed : baud rate for UART + +e.g. + +arcuart0: serial@c0fc1000 { + compatible = "snps,arc-uart"; + reg = <0xc0fc1000 0x100>; + interrupts = <5>; + clock-frequency = <80000000>; + current-speed = <115200>; + status = "okay"; +}; + +Note: Each port should have an alias correctly numbered in "aliases" node. + +e.g. +aliases { + serial0 = &arcuart0; +}; diff --git a/Documentation/devicetree/bindings/serial/atmel-usart.txt b/Documentation/devicetree/bindings/serial/atmel-usart.txt new file mode 100644 index 000000000000..2191dcb9f1da --- /dev/null +++ b/Documentation/devicetree/bindings/serial/atmel-usart.txt @@ -0,0 +1,43 @@ +* Atmel Universal Synchronous Asynchronous Receiver/Transmitter (USART) + +Required properties: +- compatible: Should be "atmel,<chip>-usart" + The compatible <chip> indicated will be the first SoC to support an + additional mode or an USART new feature. +- reg: Should contain registers location and length +- interrupts: Should contain interrupt + +Optional properties: +- atmel,use-dma-rx: use of PDC or DMA for receiving data +- atmel,use-dma-tx: use of PDC or DMA for transmitting data +- add dma bindings for dma transfer: + - dmas: DMA specifier, consisting of a phandle to DMA controller node, + memory peripheral interface and USART DMA channel ID, FIFO configuration. + Refer to dma.txt and atmel-dma.txt for details. + - dma-names: "rx" for RX channel, "tx" for TX channel. + +<chip> compatible description: +- at91rm9200: legacy USART support +- at91sam9260: generic USART implementation for SAM9 SoCs + +Example: +- use PDC: + usart0: serial@fff8c000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xfff8c000 0x4000>; + interrupts = <7>; + atmel,use-dma-rx; + atmel,use-dma-tx; + }; + +- use DMA: + usart0: serial@f001c000 { + compatible = "atmel,at91sam9260-usart"; + reg = <0xf001c000 0x100>; + interrupts = <12 4 5>; + atmel,use-dma-rx; + atmel,use-dma-tx; + dmas = <&dma0 2 0x3>, + <&dma0 2 0x204>; + dma-names = "tx", "rx"; + }; diff --git a/Documentation/devicetree/bindings/serial/efm32-uart.txt b/Documentation/devicetree/bindings/serial/efm32-uart.txt new file mode 100644 index 000000000000..8e080b893b49 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/efm32-uart.txt @@ -0,0 +1,20 @@ +* Energymicro efm32 UART + +Required properties: +- compatible : Should be "efm32,uart" +- reg : Address and length of the register set +- interrupts : Should contain uart interrupt + +Optional properties: +- location : Decides the location of the USART I/O pins. + Allowed range : [0 .. 5] + Default: 0 + +Example: + +uart@0x4000c400 { + compatible = "efm32,uart"; + reg = <0x4000c400 0x400>; + interrupts = <15>; + location = <0>; +}; diff --git a/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt new file mode 100644 index 000000000000..35ae1fb3537f --- /dev/null +++ b/Documentation/devicetree/bindings/serial/fsl-imx-uart.txt @@ -0,0 +1,29 @@ +* Freescale i.MX Universal Asynchronous Receiver/Transmitter (UART) + +Required properties: +- compatible : Should be "fsl,<soc>-uart" +- reg : Address and length of the register set for the device +- interrupts : Should contain uart interrupt + +Optional properties: +- fsl,uart-has-rtscts : Indicate the uart has rts and cts +- fsl,irda-mode : Indicate the uart supports irda mode +- fsl,dte-mode : Indicate the uart works in DTE mode. The uart works + is DCE mode by default. + +Note: Each uart controller should have an alias correctly numbered +in "aliases" node. + +Example: + +aliases { + serial0 = &uart1; +}; + +uart1: serial@73fbc000 { + compatible = "fsl,imx51-uart", "fsl,imx21-uart"; + reg = <0x73fbc000 0x4000>; + interrupts = <31>; + fsl,uart-has-rtscts; + fsl,dte-mode; +}; diff --git a/Documentation/devicetree/bindings/serial/fsl-lpuart.txt b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt new file mode 100644 index 000000000000..6fd1dd1638dd --- /dev/null +++ b/Documentation/devicetree/bindings/serial/fsl-lpuart.txt @@ -0,0 +1,14 @@ +* Freescale low power universal asynchronous receiver/transmitter (lpuart) + +Required properties: +- compatible : Should be "fsl,<soc>-lpuart" +- reg : Address and length of the register set for the device +- interrupts : Should contain uart interrupt + +Example: + +uart0: serial@40027000 { + compatible = "fsl,vf610-lpuart"; + reg = <0x40027000 0x1000>; + interrupts = <0 61 0x00>; + }; diff --git a/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt new file mode 100644 index 000000000000..59a40f18d551 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/fsl-mxs-auart.txt @@ -0,0 +1,37 @@ +* Freescale MXS Application UART (AUART) + +Required properties: +- compatible : Should be "fsl,<soc>-auart". The supported SoCs include + imx23 and imx28. +- reg : Address and length of the register set for the device +- interrupts : Should contain the auart interrupt numbers +- dmas: DMA specifier, consisting of a phandle to DMA controller node + and AUART DMA channel ID. + Refer to dma.txt and fsl-mxs-dma.txt for details. +- dma-names: "rx" for RX channel, "tx" for TX channel. + +Optional properties: +- fsl,uart-has-rtscts : Indicate the UART has RTS and CTS lines, + it also means you enable the DMA support for this UART. + +Example: +auart0: serial@8006a000 { + compatible = "fsl,imx28-auart", "fsl,imx23-auart"; + reg = <0x8006a000 0x2000>; + interrupts = <112>; + dmas = <&dma_apbx 8>, <&dma_apbx 9>; + dma-names = "rx", "tx"; +}; + +Note: Each auart port should have an alias correctly numbered in "aliases" +node. + +Example: + +aliases { + serial0 = &auart0; + serial1 = &auart1; + serial2 = &auart2; + serial3 = &auart3; + serial4 = &auart4; +}; diff --git a/Documentation/devicetree/bindings/serial/nxp-lpc32xx-hsuart.txt b/Documentation/devicetree/bindings/serial/nxp-lpc32xx-hsuart.txt new file mode 100644 index 000000000000..0d439dfc1aa5 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/nxp-lpc32xx-hsuart.txt @@ -0,0 +1,14 @@ +* NXP LPC32xx SoC High Speed UART + +Required properties: +- compatible: Should be "nxp,lpc3220-hsuart" +- reg: Should contain registers location and length +- interrupts: Should contain interrupt + +Example: + + uart1: serial@40014000 { + compatible = "nxp,lpc3220-hsuart"; + reg = <0x40014000 0x1000>; + interrupts = <26 0>; + }; diff --git a/Documentation/devicetree/bindings/serial/of-serial.txt b/Documentation/devicetree/bindings/serial/of-serial.txt new file mode 100644 index 000000000000..1928a3e83cd0 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/of-serial.txt @@ -0,0 +1,49 @@ +* UART (Universal Asynchronous Receiver/Transmitter) + +Required properties: +- compatible : one of: + - "ns8250" + - "ns16450" + - "ns16550a" + - "ns16550" + - "ns16750" + - "ns16850" + - "nvidia,tegra20-uart" + - "nxp,lpc3220-uart" + - "ibm,qpace-nwp-serial" + - "altr,16550-FIFO32" + - "altr,16550-FIFO64" + - "altr,16550-FIFO128" + - "serial" if the port type is unknown. +- reg : offset and length of the register set for the device. +- interrupts : should contain uart interrupt. +- clock-frequency : the input clock frequency for the UART + or + clocks phandle to refer to the clk used as per Documentation/devicetree + /bindings/clock/clock-bindings.txt + +Optional properties: +- current-speed : the current active speed of the UART. +- reg-offset : offset to apply to the mapbase from the start of the registers. +- reg-shift : quantity to shift the register offsets by. +- reg-io-width : the size (in bytes) of the IO accesses that should be + performed on the device. There are some systems that require 32-bit + accesses to the UART (e.g. TI davinci). +- used-by-rtas : set to indicate that the port is in use by the OpenFirmware + RTAS and should not be registered. +- no-loopback-test: set to indicate that the port does not implements loopback + test mode +- fifo-size: the fifo size of the UART. +- auto-flow-control: one way to enable automatic flow control support. The + driver is allowed to detect support for the capability even without this + property. + +Example: + + uart@80230000 { + compatible = "ns8250"; + reg = <0x80230000 0x100>; + clock-frequency = <3686400>; + interrupts = <10>; + reg-shift = <2>; + }; diff --git a/Documentation/devicetree/bindings/serial/sirf-uart.txt b/Documentation/devicetree/bindings/serial/sirf-uart.txt new file mode 100644 index 000000000000..a2dfc6522a91 --- /dev/null +++ b/Documentation/devicetree/bindings/serial/sirf-uart.txt @@ -0,0 +1,33 @@ +* CSR SiRFprimaII/atlasVI Universal Synchronous Asynchronous Receiver/Transmitter * + +Required properties: +- compatible : Should be "sirf,prima2-uart" or "sirf, prima2-usp-uart" +- reg : Offset and length of the register set for the device +- interrupts : Should contain uart interrupt +- fifosize : Should define hardware rx/tx fifo size +- clocks : Should contain uart clock number + +Optional properties: +- sirf,uart-has-rtscts: we have hardware flow controller pins in hardware +- rts-gpios: RTS pin for USP-based UART if sirf,uart-has-rtscts is true +- cts-gpios: CTS pin for USP-based UART if sirf,uart-has-rtscts is true + +Example: + +uart0: uart@b0050000 { + cell-index = <0>; + compatible = "sirf,prima2-uart"; + reg = <0xb0050000 0x1000>; + interrupts = <17>; + fifosize = <128>; + clocks = <&clks 13>; +}; + +On the board-specific dts, we can put rts-gpios and cts-gpios like + +usp@b0090000 { + compatible = "sirf,prima2-usp-uart"; + sirf,uart-has-rtscts; + rts-gpios = <&gpio 15 0>; + cts-gpios = <&gpio 46 0>; +}; diff --git a/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt new file mode 100644 index 000000000000..f13f1c5be91c --- /dev/null +++ b/Documentation/devicetree/bindings/serial/snps-dw-apb-uart.txt @@ -0,0 +1,25 @@ +* Synopsys DesignWare ABP UART + +Required properties: +- compatible : "snps,dw-apb-uart" +- reg : offset and length of the register set for the device. +- interrupts : should contain uart interrupt. +- clock-frequency : the input clock frequency for the UART. + +Optional properties: +- reg-shift : quantity to shift the register offsets by. If this property is + not present then the register offsets are not shifted. +- reg-io-width : the size (in bytes) of the IO accesses that should be + performed on the device. If this property is not present then single byte + accesses are used. + +Example: + + uart@80230000 { + compatible = "snps,dw-apb-uart"; + reg = <0x80230000 0x100>; + clock-frequency = <3686400>; + interrupts = <10>; + reg-shift = <2>; + reg-io-width = <4>; + }; diff --git a/Documentation/devicetree/bindings/serial/st-asc.txt b/Documentation/devicetree/bindings/serial/st-asc.txt new file mode 100644 index 000000000000..75d877f5968f --- /dev/null +++ b/Documentation/devicetree/bindings/serial/st-asc.txt @@ -0,0 +1,18 @@ +*st-asc(Serial Port) + +Required properties: +- compatible : Should be "st,asc". +- reg, reg-names, interrupts, interrupt-names : Standard way to define device + resources with names. look in + Documentation/devicetree/bindings/resource-names.txt + +Optional properties: +- st,hw-flow-ctrl bool flag to enable hardware flow control. +- st,force-m1 bool flat to force asc to be in Mode-1 recommeded + for high bit rates (above 19.2K) +Example: +serial@fe440000{ + compatible = "st,asc"; + reg = <0xfe440000 0x2c>; + interrupts = <0 209 0>; +}; diff --git a/Documentation/devicetree/bindings/serial/via,vt8500-uart.txt b/Documentation/devicetree/bindings/serial/via,vt8500-uart.txt new file mode 100644 index 000000000000..5feef1ef167d --- /dev/null +++ b/Documentation/devicetree/bindings/serial/via,vt8500-uart.txt @@ -0,0 +1,17 @@ +VIA/Wondermedia VT8500 UART Controller +----------------------------------------------------- + +Required properties: +- compatible : "via,vt8500-uart" +- reg : Should contain 1 register ranges(address and length) +- interrupts : UART interrupt +- clocks : phandle to the uart source clock (usually a 24Mhz fixed clock) + +Example: + + uart@d8210000 { + compatible = "via,vt8500-uart"; + reg = <0xd8210000 0x1040>; + interrupts = <47>; + clocks = <&ref24>; + }; |
