Merge tag 'v3.3' into staging/for_v3.4

* tag 'v3.3': (1646 commits)
  Linux 3.3
  Don't limit non-nested epoll paths
  netfilter: ctnetlink: fix race between delete and timeout expiration
  ipv6: Don't dev_hold(dev) in ip6_mc_find_dev_rcu.
  nilfs2: fix NULL pointer dereference in nilfs_load_super_block()
  nilfs2: clamp ns_r_segments_percentage to [1, 99]
  afs: Remote abort can cause BUG in rxrpc code
  afs: Read of file returns EBADMSG
  C6X: remove dead code from entry.S
  wimax/i2400m: fix erroneous NETDEV_TX_BUSY use
  net/hyperv: fix erroneous NETDEV_TX_BUSY use
  net/usbnet: reserve headroom on rx skbs
  bnx2x: fix memory leak in bnx2x_init_firmware()
  bnx2x: fix a crash on corrupt firmware file
  sch_sfq: revert dont put new flow at the end of flows
  ipv6: fix icmp6_dst_alloc()
  MAINTAINERS: Add Serge as maintainer of capabilities
  drivers/video/backlight/s6e63m0.c: fix corruption storing gamma mode
  MAINTAINERS: add entry for exynos mipi display drivers
  MAINTAINERS: fix link to Gustavo Padovans tree
  ...

1 files changed, 12 insertions, 3 deletions

diff --git a/drivers/mmc/core/sdio.c b/drivers/mmc/core/sdio.c
index bd7bacc950dc..2c7c83f832d2 100644
--- a/drivers/mmc/core/sdio.c
+++ b/drivers/mmc/core/sdio.c
@@ -98,10 +98,11 @@ fail:
 	return ret;
 }
 
-static int sdio_read_cccr(struct mmc_card *card)
+static int sdio_read_cccr(struct mmc_card *card, u32 ocr)
 {
 	int ret;
 	int cccr_vsn;
+	int uhs = ocr & R4_18V_PRESENT;
 	unsigned char data;
 	unsigned char speed;
 
@@ -149,7 +150,7 @@ static int sdio_read_cccr(struct mmc_card *card)
 		card->scr.sda_spec3 = 0;
 		card->sw_caps.sd3_bus_mode = 0;
 		card->sw_caps.sd3_drv_type = 0;
-		if (cccr_vsn >= SDIO_CCCR_REV_3_00) {
+		if (cccr_vsn >= SDIO_CCCR_REV_3_00 && uhs) {
 			card->scr.sda_spec3 = 1;
 			ret = mmc_io_rw_direct(card, 0, 0,
 				SDIO_CCCR_UHS, 0, &data);
@@ -584,6 +585,9 @@ static int mmc_sdio_init_card(struct mmc_host *host, u32 ocr,
 	 * Inform the card of the voltage
 	 */
 	if (!powered_resume) {
+		/* The initialization should be done at 3.3 V I/O voltage. */
+		mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, 0);
+
 		err = mmc_send_io_op_cond(host, host->ocr, &ocr);
 		if (err)
 			goto err;
@@ -712,7 +716,7 @@ static int mmc_sdio_init_card(struct mmc_host *host, u32 ocr,
 	/*
 	 * Read the common registers.
 	 */
-	err = sdio_read_cccr(card);
+	err = sdio_read_cccr(card, ocr);
 	if (err)
 		goto remove;
 
@@ -995,6 +999,11 @@ static int mmc_sdio_power_restore(struct mmc_host *host)
 	 * With these steps taken, mmc_select_voltage() is also required to
 	 * restore the correct voltage setting of the card.
 	 */
+
+	/* The initialization should be done at 3.3 V I/O voltage. */
+	if (!mmc_card_keep_power(host))
+		mmc_set_signal_voltage(host, MMC_SIGNAL_VOLTAGE_330, 0);
+
 	sdio_reset(host);
 	mmc_go_idle(host);
 	mmc_send_if_cond(host, host->ocr_avail);