Merge branch 'sh/nommu' into sh-latest

5 files changed, 406 insertions, 978 deletions

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 5099681cf503..573532f7553e 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -141,6 +141,12 @@ config GPIO_PL061
 	help
 	  Say yes here to support the PrimeCell PL061 GPIO device
 
+config GPIO_PXA
+	bool "PXA GPIO support"
+	depends on ARCH_PXA || ARCH_MMP
+	help
+	  Say yes here to support the PXA GPIO device
+
 config GPIO_XILINX
 	bool "Xilinx GPIO support"
 	depends on PPC_OF || MICROBLAZE
@@ -170,15 +176,6 @@ config GPIO_SCH
 	  The Intel Tunnel Creek processor has 5 GPIOs powered by the
 	  core power rail and 9 from suspend power supply.
 
-config GPIO_U300
-	bool "ST-Ericsson U300 COH 901 335/571 GPIO"
-	depends on GPIOLIB && ARCH_U300
-	help
-	  Say yes here to support GPIO interface on ST-Ericsson U300.
-	  The names of the two IP block variants supported are
-	  COH 901 335 and COH 901 571/3. They contain 3, 5 or 7
-	  ports of 8 GPIO pins each.
-
 config GPIO_VX855
 	tristate "VIA VX855/VX875 GPIO"
 	depends on PCI
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 4e018d6a7639..62e641e79e8f 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -40,7 +40,7 @@ obj-$(CONFIG_GPIO_PCA953X)	+= gpio-pca953x.o
 obj-$(CONFIG_GPIO_PCF857X)	+= gpio-pcf857x.o
 obj-$(CONFIG_GPIO_PCH)		+= gpio-pch.o
 obj-$(CONFIG_GPIO_PL061)	+= gpio-pl061.o
-obj-$(CONFIG_PLAT_PXA)		+= gpio-pxa.o
+obj-$(CONFIG_GPIO_PXA)		+= gpio-pxa.o
 obj-$(CONFIG_GPIO_RDC321X)	+= gpio-rdc321x.o
 obj-$(CONFIG_PLAT_SAMSUNG)	+= gpio-samsung.o
 obj-$(CONFIG_ARCH_SA1100)	+= gpio-sa1100.o
@@ -54,7 +54,6 @@ obj-$(CONFIG_ARCH_DAVINCI_TNETV107X) += gpio-tnetv107x.o
 obj-$(CONFIG_GPIO_TPS65910)	+= gpio-tps65910.o
 obj-$(CONFIG_GPIO_TPS65912)	+= gpio-tps65912.o
 obj-$(CONFIG_GPIO_TWL4030)	+= gpio-twl4030.o
-obj-$(CONFIG_MACH_U300)		+= gpio-u300.o
 obj-$(CONFIG_GPIO_UCB1400)	+= gpio-ucb1400.o
 obj-$(CONFIG_GPIO_VR41XX)	+= gpio-vr41xx.o
 obj-$(CONFIG_GPIO_VX855)	+= gpio-vx855.o
diff --git a/drivers/gpio/gpio-pxa.c b/drivers/gpio/gpio-pxa.c
index ee137712f9db..b2d3ee1d183a 100644
--- a/drivers/gpio/gpio-pxa.c
+++ b/drivers/gpio/gpio-pxa.c
@@ -11,14 +11,46 @@
  *  it under the terms of the GNU General Public License version 2 as
  *  published by the Free Software Foundation.
  */
+#include <linux/clk.h>
+#include <linux/err.h>
 #include <linux/gpio.h>
+#include <linux/gpio-pxa.h>
 #include <linux/init.h>
 #include <linux/irq.h>
 #include <linux/io.h>
+#include <linux/platform_device.h>
 #include <linux/syscore_ops.h>
 #include <linux/slab.h>
 
-#include <mach/gpio-pxa.h>
+/*
+ * We handle the GPIOs by banks, each bank covers up to 32 GPIOs with
+ * one set of registers. The register offsets are organized below:
+ *
+ *           GPLR    GPDR    GPSR    GPCR    GRER    GFER    GEDR
+ * BANK 0 - 0x0000  0x000C  0x0018  0x0024  0x0030  0x003C  0x0048
+ * BANK 1 - 0x0004  0x0010  0x001C  0x0028  0x0034  0x0040  0x004C
+ * BANK 2 - 0x0008  0x0014  0x0020  0x002C  0x0038  0x0044  0x0050
+ *
+ * BANK 3 - 0x0100  0x010C  0x0118  0x0124  0x0130  0x013C  0x0148
+ * BANK 4 - 0x0104  0x0110  0x011C  0x0128  0x0134  0x0140  0x014C
+ * BANK 5 - 0x0108  0x0114  0x0120  0x012C  0x0138  0x0144  0x0150
+ *
+ * NOTE:
+ *   BANK 3 is only available on PXA27x and later processors.
+ *   BANK 4 and 5 are only available on PXA935
+ */
+
+#define GPLR_OFFSET	0x00
+#define GPDR_OFFSET	0x0C
+#define GPSR_OFFSET	0x18
+#define GPCR_OFFSET	0x24
+#define GRER_OFFSET	0x30
+#define GFER_OFFSET	0x3C
+#define GEDR_OFFSET	0x48
+#define GAFR_OFFSET	0x54
+#define ED_MASK_OFFSET	0x9C	/* GPIO edge detection for AP side */
+
+#define BANK_OFF(n)	(((n) < 3) ? (n) << 2 : 0x100 + (((n) - 3) << 2))
 
 int pxa_last_gpio;
 
@@ -39,8 +71,20 @@ struct pxa_gpio_chip {
 #endif
 };
 
+enum {
+	PXA25X_GPIO = 0,
+	PXA26X_GPIO,
+	PXA27X_GPIO,
+	PXA3XX_GPIO,
+	PXA93X_GPIO,
+	MMP_GPIO = 0x10,
+	MMP2_GPIO,
+};
+
 static DEFINE_SPINLOCK(gpio_lock);
 static struct pxa_gpio_chip *pxa_gpio_chips;
+static int gpio_type;
+static void __iomem *gpio_reg_base;
 
 #define for_each_gpio_chip(i, c)			\
 	for (i = 0, c = &pxa_gpio_chips[0]; i <= pxa_last_gpio; i += 32, c++)
@@ -55,6 +99,122 @@ static inline struct pxa_gpio_chip *gpio_to_pxachip(unsigned gpio)
 	return &pxa_gpio_chips[gpio_to_bank(gpio)];
 }
 
+static inline int gpio_is_pxa_type(int type)
+{
+	return (type & MMP_GPIO) == 0;
+}
+
+static inline int gpio_is_mmp_type(int type)
+{
+	return (type & MMP_GPIO) != 0;
+}
+
+/* GPIO86/87/88/89 on PXA26x have their direction bits in PXA_GPDR(2 inverted,
+ * as well as their Alternate Function value being '1' for GPIO in GAFRx.
+ */
+static inline int __gpio_is_inverted(int gpio)
+{
+	if ((gpio_type == PXA26X_GPIO) && (gpio > 85))
+		return 1;
+	return 0;
+}
+
+/*
+ * On PXA25x and PXA27x, GAFRx and GPDRx together decide the alternate
+ * function of a GPIO, and GPDRx cannot be altered once configured. It
+ * is attributed as "occupied" here (I know this terminology isn't
+ * accurate, you are welcome to propose a better one :-)
+ */
+static inline int __gpio_is_occupied(unsigned gpio)
+{
+	struct pxa_gpio_chip *pxachip;
+	void __iomem *base;
+	unsigned long gafr = 0, gpdr = 0;
+	int ret, af = 0, dir = 0;
+
+	pxachip = gpio_to_pxachip(gpio);
+	base = gpio_chip_base(&pxachip->chip);
+	gpdr = readl_relaxed(base + GPDR_OFFSET);
+
+	switch (gpio_type) {
+	case PXA25X_GPIO:
+	case PXA26X_GPIO:
+	case PXA27X_GPIO:
+		gafr = readl_relaxed(base + GAFR_OFFSET);
+		af = (gafr >> ((gpio & 0xf) * 2)) & 0x3;
+		dir = gpdr & GPIO_bit(gpio);
+
+		if (__gpio_is_inverted(gpio))
+			ret = (af != 1) || (dir == 0);
+		else
+			ret = (af != 0) || (dir != 0);
+		break;
+	default:
+		ret = gpdr & GPIO_bit(gpio);
+		break;
+	}
+	return ret;
+}
+
+#ifdef CONFIG_ARCH_PXA
+static inline int __pxa_gpio_to_irq(int gpio)
+{
+	if (gpio_is_pxa_type(gpio_type))
+		return PXA_GPIO_TO_IRQ(gpio);
+	return -1;
+}
+
+static inline int __pxa_irq_to_gpio(int irq)
+{
+	if (gpio_is_pxa_type(gpio_type))
+		return irq - PXA_GPIO_TO_IRQ(0);
+	return -1;
+}
+#else
+static inline int __pxa_gpio_to_irq(int gpio) { return -1; }
+static inline int __pxa_irq_to_gpio(int irq) { return -1; }
+#endif
+
+#ifdef CONFIG_ARCH_MMP
+static inline int __mmp_gpio_to_irq(int gpio)
+{
+	if (gpio_is_mmp_type(gpio_type))
+		return MMP_GPIO_TO_IRQ(gpio);
+	return -1;
+}
+
+static inline int __mmp_irq_to_gpio(int irq)
+{
+	if (gpio_is_mmp_type(gpio_type))
+		return irq - MMP_GPIO_TO_IRQ(0);
+	return -1;
+}
+#else
+static inline int __mmp_gpio_to_irq(int gpio) { return -1; }
+static inline int __mmp_irq_to_gpio(int irq) { return -1; }
+#endif
+
+static int pxa_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
+{
+	int gpio, ret;
+
+	gpio = chip->base + offset;
+	ret = __pxa_gpio_to_irq(gpio);
+	if (ret >= 0)
+		return ret;
+	return __mmp_gpio_to_irq(gpio);
+}
+
+int pxa_irq_to_gpio(int irq)
+{
+	int ret;
+
+	ret = __pxa_irq_to_gpio(irq);
+	if (ret >= 0)
+		return ret;
+	return __mmp_irq_to_gpio(irq);
+}
+
 static int pxa_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
 {
 	void __iomem *base = gpio_chip_base(chip);
@@ -63,12 +223,12 @@ static int pxa_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
 
 	spin_lock_irqsave(&gpio_lock, flags);
 
-	value = __raw_readl(base + GPDR_OFFSET);
+	value = readl_relaxed(base + GPDR_OFFSET);
 	if (__gpio_is_inverted(chip->base + offset))
 		value |= mask;
 	else
 		value &= ~mask;
-	__raw_writel(value, base + GPDR_OFFSET);
+	writel_relaxed(value, base + GPDR_OFFSET);
 
 	spin_unlock_irqrestore(&gpio_lock, flags);
 	return 0;
@@ -81,16 +241,16 @@ static int pxa_gpio_direction_output(struct gpio_chip *chip,
 	uint32_t tmp, mask = 1 << offset;
 	unsigned long flags;
 
-	__raw_writel(mask, base + (value ? GPSR_OFFSET : GPCR_OFFSET));
+	writel_relaxed(mask, base + (value ? GPSR_OFFSET : GPCR_OFFSET));
 
 	spin_lock_irqsave(&gpio_lock, flags);
 
-	tmp = __raw_readl(base + GPDR_OFFSET);
+	tmp = readl_relaxed(base + GPDR_OFFSET);
 	if (__gpio_is_inverted(chip->base + offset))
 		tmp &= ~mask;
 	else
 		tmp |= mask;
-	__raw_writel(tmp, base + GPDR_OFFSET);
+	writel_relaxed(tmp, base + GPDR_OFFSET);
 
 	spin_unlock_irqrestore(&gpio_lock, flags);
 	return 0;
@@ -98,16 +258,16 @@ static int pxa_gpio_direction_output(struct gpio_chip *chip,
 
 static int pxa_gpio_get(struct gpio_chip *chip, unsigned offset)
 {
-	return __raw_readl(gpio_chip_base(chip) + GPLR_OFFSET) & (1 << offset);
+	return readl_relaxed(gpio_chip_base(chip) + GPLR_OFFSET) & (1 << offset);
 }
 
 static void pxa_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
 {
-	__raw_writel(1 << offset, gpio_chip_base(chip) +
+	writel_relaxed(1 << offset, gpio_chip_base(chip) +
 				(value ? GPSR_OFFSET : GPCR_OFFSET));
 }
 
-static int __init pxa_init_gpio_chip(int gpio_end)
+static int __devinit pxa_init_gpio_chip(int gpio_end)
 {
 	int i, gpio, nbanks = gpio_to_bank(gpio_end) + 1;
 	struct pxa_gpio_chip *chips;
@@ -122,7 +282,7 @@ static int __init pxa_init_gpio_chip(int gpio_end)
 		struct gpio_chip *c = &chips[i].chip;
 
 		sprintf(chips[i].label, "gpio-%d", i);
-		chips[i].regbase = GPIO_BANK(i);
+		chips[i].regbase = gpio_reg_base + BANK_OFF(i);
 
 		c->base  = gpio;
 		c->label = chips[i].label;
@@ -131,6 +291,7 @@ static int __init pxa_init_gpio_chip(int gpio_end)
 		c->direction_output = pxa_gpio_direction_output;
 		c->get = pxa_gpio_get;
 		c->set = pxa_gpio_set;
+		c->to_irq = pxa_gpio_to_irq;
 
 		/* number of GPIOs on last bank may be less than 32 */
 		c->ngpio = (gpio + 31 > gpio_end) ? (gpio_end - gpio + 1) : 32;
@@ -147,18 +308,18 @@ static inline void update_edge_detect(struct pxa_gpio_chip *c)
 {
 	uint32_t grer, gfer;
 
-	grer = __raw_readl(c->regbase + GRER_OFFSET) & ~c->irq_mask;
-	gfer = __raw_readl(c->regbase + GFER_OFFSET) & ~c->irq_mask;
+	grer = readl_relaxed(c->regbase + GRER_OFFSET) & ~c->irq_mask;
+	gfer = readl_relaxed(c->regbase + GFER_OFFSET) & ~c->irq_mask;
 	grer |= c->irq_edge_rise & c->irq_mask;
 	gfer |= c->irq_edge_fall & c->irq_mask;
-	__raw_writel(grer, c->regbase + GRER_OFFSET);
-	__raw_writel(gfer, c->regbase + GFER_OFFSET);
+	writel_relaxed(grer, c->regbase + GRER_OFFSET);
+	writel_relaxed(gfer, c->regbase + GFER_OFFSET);
 }
 
 static int pxa_gpio_irq_type(struct irq_data *d, unsigned int type)
 {
 	struct pxa_gpio_chip *c;
-	int gpio = irq_to_gpio(d->irq);
+	int gpio = pxa_irq_to_gpio(d->irq);
 	unsigned long gpdr, mask = GPIO_bit(gpio);
 
 	c = gpio_to_pxachip(gpio);
@@ -176,12 +337,12 @@ static int pxa_gpio_irq_type(struct irq_data *d, unsigned int type)
 		type = IRQ_TYPE_EDGE_RISING | IRQ_TYPE_EDGE_FALLING;
 	}
 
-	gpdr = __raw_readl(c->regbase + GPDR_OFFSET);
+	gpdr = readl_relaxed(c->regbase + GPDR_OFFSET);
 
 	if (__gpio_is_inverted(gpio))
-		__raw_writel(gpdr | mask,  c->regbase + GPDR_OFFSET);
+		writel_relaxed(gpdr | mask,  c->regbase + GPDR_OFFSET);
 	else
-		__raw_writel(gpdr & ~mask, c->regbase + GPDR_OFFSET);
+		writel_relaxed(gpdr & ~mask, c->regbase + GPDR_OFFSET);
 
 	if (type & IRQ_TYPE_EDGE_RISING)
 		c->irq_edge_rise |= mask;
@@ -212,9 +373,9 @@ static void pxa_gpio_demux_handler(unsigned int irq, struct irq_desc *desc)
 		for_each_gpio_chip(gpio, c) {
 			gpio_base = c->chip.base;
 
-			gedr = __raw_readl(c->regbase + GEDR_OFFSET);
+			gedr = readl_relaxed(c->regbase + GEDR_OFFSET);
 			gedr = gedr & c->irq_mask;
-			__raw_writel(gedr, c->regbase + GEDR_OFFSET);
+			writel_relaxed(gedr, c->regbase + GEDR_OFFSET);
 
 			n = find_first_bit(&gedr, BITS_PER_LONG);
 			while (n < BITS_PER_LONG) {
@@ -229,29 +390,29 @@ static void pxa_gpio_demux_handler(unsigned int irq, struct irq_desc *desc)
 
 static void pxa_ack_muxed_gpio(struct irq_data *d)
 {
-	int gpio = irq_to_gpio(d->irq);
+	int gpio = pxa_irq_to_gpio(d->irq);
 	struct pxa_gpio_chip *c = gpio_to_pxachip(gpio);
 
-	__raw_writel(GPIO_bit(gpio), c->regbase + GEDR_OFFSET);
+	writel_relaxed(GPIO_bit(gpio), c->regbase + GEDR_OFFSET);
 }
 
 static void pxa_mask_muxed_gpio(struct irq_data *d)
 {
-	int gpio = irq_to_gpio(d->irq);
+	int gpio = pxa_irq_to_gpio(d->irq);
 	struct pxa_gpio_chip *c = gpio_to_pxachip(gpio);
 	uint32_t grer, gfer;
 
 	c->irq_mask &= ~GPIO_bit(gpio);
 
-	grer = __raw_readl(c->regbase + GRER_OFFSET) & ~GPIO_bit(gpio);
-	gfer = __raw_readl(c->regbase + GFER_OFFSET) & ~GPIO_bit(gpio);
-	__raw_writel(grer, c->regbase + GRER_OFFSET);
-	__raw_writel(gfer, c->regbase + GFER_OFFSET);
+	grer = readl_relaxed(c->regbase + GRER_OFFSET) & ~GPIO_bit(gpio);
+	gfer = readl_relaxed(c->regbase + GFER_OFFSET) & ~GPIO_bit(gpio);
+	writel_relaxed(grer, c->regbase + GRER_OFFSET);
+	writel_relaxed(gfer, c->regbase + GFER_OFFSET);
 }
 
 static void pxa_unmask_muxed_gpio(struct irq_data *d)
 {
-	int gpio = irq_to_gpio(d->irq);
+	int gpio = pxa_irq_to_gpio(d->irq);
 	struct pxa_gpio_chip *c = gpio_to_pxachip(gpio);
 
 	c->irq_mask |= GPIO_bit(gpio);
@@ -266,34 +427,143 @@ static struct irq_chip pxa_muxed_gpio_chip = {
 	.irq_set_type	= pxa_gpio_irq_type,
 };
 
-void __init pxa_init_gpio(int mux_irq, int start, int end, set_wake_t fn)
+static int pxa_gpio_nums(void)
 {
-	struct pxa_gpio_chip *c;
-	int gpio, irq;
+	int count = 0;
+
+#ifdef CONFIG_ARCH_PXA
+	if (cpu_is_pxa25x()) {
+#ifdef CONFIG_CPU_PXA26x
+		count = 89;
+		gpio_type = PXA26X_GPIO;
+#elif defined(CONFIG_PXA25x)
+		count = 84;
+		gpio_type = PXA26X_GPIO;
+#endif /* CONFIG_CPU_PXA26x */
+	} else if (cpu_is_pxa27x()) {
+		count = 120;
+		gpio_type = PXA27X_GPIO;
+	} else if (cpu_is_pxa93x() || cpu_is_pxa95x()) {
+		count = 191;
+		gpio_type = PXA93X_GPIO;
+	} else if (cpu_is_pxa3xx()) {
+		count = 127;
+		gpio_type = PXA3XX_GPIO;
+	}
+#endif /* CONFIG_ARCH_PXA */
+
+#ifdef CONFIG_ARCH_MMP
+	if (cpu_is_pxa168() || cpu_is_pxa910()) {
+		count = 127;
+		gpio_type = MMP_GPIO;
+	} else if (cpu_is_mmp2()) {
+		count = 191;
+		gpio_type = MMP2_GPIO;
+	}
+#endif /* CONFIG_ARCH_MMP */
+	return count;
+}
 
-	pxa_last_gpio = end;
+static int __devinit pxa_gpio_probe(struct platform_device *pdev)
+{
+	struct pxa_gpio_chip *c;
+	struct resource *res;
+	struct clk *clk;
+	int gpio, irq, ret;
+	int irq0 = 0, irq1 = 0, irq_mux, gpio_offset = 0;
+
+	pxa_last_gpio = pxa_gpio_nums();
+	if (!pxa_last_gpio)
+		return -EINVAL;
+
+	irq0 = platform_get_irq_byname(pdev, "gpio0");
+	irq1 = platform_get_irq_byname(pdev, "gpio1");
+	irq_mux = platform_get_irq_byname(pdev, "gpio_mux");
+	if ((irq0 > 0 && irq1 <= 0) || (irq0 <= 0 && irq1 > 0)
+		|| (irq_mux <= 0))
+		return -EINVAL;
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -EINVAL;
+	gpio_reg_base = ioremap(res->start, resource_size(res));
+	if (!gpio_reg_base)
+		return -EINVAL;
+
+	if (irq0 > 0)
+		gpio_offset = 2;
+
+	clk = clk_get(&pdev->dev, NULL);
+	if (IS_ERR(clk)) {
+		dev_err(&pdev->dev, "Error %ld to get gpio clock\n",
+			PTR_ERR(clk));
+		iounmap(gpio_reg_base);
+		return PTR_ERR(clk);
+	}
+	ret = clk_prepare(clk);
+	if (ret) {
+		clk_put(clk);
+		iounmap(gpio_reg_base);
+		return ret;
+	}
+	ret = clk_enable(clk);
+	if (ret) {
+		clk_unprepare(clk);
+		clk_put(clk);
+		iounmap(gpio_reg_base);
+		return ret;
+	}
 
 	/* Initialize GPIO chips */
-	pxa_init_gpio_chip(end);
+	pxa_init_gpio_chip(pxa_last_gpio);
 
 	/* clear all GPIO edge detects */
 	for_each_gpio_chip(gpio, c) {
-		__raw_writel(0, c->regbase + GFER_OFFSET);
-		__raw_writel(0, c->regbase + GRER_OFFSET);
-		__raw_writel(~0,c->regbase + GEDR_OFFSET);
+		writel_relaxed(0, c->regbase + GFER_OFFSET);
+		writel_relaxed(0, c->regbase + GRER_OFFSET);
+		writel_relaxed(~0,c->regbase + GEDR_OFFSET);
+		/* unmask GPIO edge detect for AP side */
+		if (gpio_is_mmp_type(gpio_type))
+			writel_relaxed(~0, c->regbase + ED_MASK_OFFSET);
 	}
 
-	for (irq  = gpio_to_irq(start); irq <= gpio_to_irq(end); irq++) {
+#ifdef CONFIG_ARCH_PXA
+	irq = gpio_to_irq(0);
+	irq_set_chip_and_handler(irq, &pxa_muxed_gpio_chip,
+				 handle_edge_irq);
+	set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+	irq_set_chained_handler(IRQ_GPIO0, pxa_gpio_demux_handler);
+
+	irq = gpio_to_irq(1);
+	irq_set_chip_and_handler(irq, &pxa_muxed_gpio_chip,
+				 handle_edge_irq);
+	set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
+	irq_set_chained_handler(IRQ_GPIO1, pxa_gpio_demux_handler);
+#endif
+
+	for (irq  = gpio_to_irq(gpio_offset);
+		irq <= gpio_to_irq(pxa_last_gpio); irq++) {
 		irq_set_chip_and_handler(irq, &pxa_muxed_gpio_chip,
 					 handle_edge_irq);
 		set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
 	}
 
-	/* Install handler for GPIO>=2 edge detect interrupts */
-	irq_set_chained_handler(mux_irq, pxa_gpio_demux_handler);
-	pxa_muxed_gpio_chip.irq_set_wake = fn;
+	irq_set_chained_handler(irq_mux, pxa_gpio_demux_handler);
+	return 0;
 }
 
+static struct platform_driver pxa_gpio_driver = {
+	.probe		= pxa_gpio_probe,
+	.driver		= {
+		.name	= "pxa-gpio",
+	},
+};
+
+static int __init pxa_gpio_init(void)
+{
+	return platform_driver_register(&pxa_gpio_driver);
+}
+postcore_initcall(pxa_gpio_init);
+
 #ifdef CONFIG_PM
 static int pxa_gpio_suspend(void)
 {
@@ -301,13 +571,13 @@ static int pxa_gpio_suspend(void)
 	int gpio;
 
 	for_each_gpio_chip(gpio, c) {
-		c->saved_gplr = __raw_readl(c->regbase + GPLR_OFFSET);
-		c->saved_gpdr = __raw_readl(c->regbase + GPDR_OFFSET);
-		c->saved_grer = __raw_readl(c->regbase + GRER_OFFSET);
-		c->saved_gfer = __raw_readl(c->regbase + GFER_OFFSET);
+		c->saved_gplr = readl_relaxed(c->regbase + GPLR_OFFSET);
+		c->saved_gpdr = readl_relaxed(c->regbase + GPDR_OFFSET);
+		c->saved_grer = readl_relaxed(c->regbase + GRER_OFFSET);
+		c->saved_gfer = readl_relaxed(c->regbase + GFER_OFFSET);
 
 		/* Clear GPIO transition detect bits */
-		__raw_writel(0xffffffff, c->regbase + GEDR_OFFSET);
+		writel_relaxed(0xffffffff, c->regbase + GEDR_OFFSET);
 	}
 	return 0;
 }
@@ -319,12 +589,12 @@ static void pxa_gpio_resume(void)
 
 	for_each_gpio_chip(gpio, c) {
 		/* restore level with set/clear */
-		__raw_writel( c->saved_gplr, c->regbase + GPSR_OFFSET);
-		__raw_writel(~c->saved_gplr, c->regbase + GPCR_OFFSET);
+		writel_relaxed( c->saved_gplr, c->regbase + GPSR_OFFSET);
+		writel_relaxed(~c->saved_gplr, c->regbase + GPCR_OFFSET);
 
-		__raw_writel(c->saved_grer, c->regbase + GRER_OFFSET);
-		__raw_writel(c->saved_gfer, c->regbase + GFER_OFFSET);
-		__raw_writel(c->saved_gpdr, c->regbase + GPDR_OFFSET);
+		writel_relaxed(c->saved_grer, c->regbase + GRER_OFFSET);
+		writel_relaxed(c->saved_gfer, c->regbase + GFER_OFFSET);
+		writel_relaxed(c->saved_gpdr, c->regbase + GPDR_OFFSET);
 	}
 }
 #else
@@ -336,3 +606,10 @@ struct syscore_ops pxa_gpio_syscore_ops = {
 	.suspend	= pxa_gpio_suspend,
 	.resume		= pxa_gpio_resume,
 };
+
+static int __init pxa_gpio_sysinit(void)
+{
+	register_syscore_ops(&pxa_gpio_syscore_ops);
+	return 0;
+}
+postcore_initcall(pxa_gpio_sysinit);
diff --git a/drivers/gpio/gpio-samsung.c b/drivers/gpio/gpio-samsung.c
index ab098ba9f1dd..a7661773c052 100644
--- a/drivers/gpio/gpio-samsung.c
+++ b/drivers/gpio/gpio-samsung.c
@@ -24,6 +24,9 @@
 #include <linux/interrupt.h>
 #include <linux/device.h>
 #include <linux/ioport.h>
+#include <linux/of.h>
+#include <linux/slab.h>
+#include <linux/of_address.h>
 
 #include <asm/irq.h>
 
@@ -2383,6 +2386,63 @@ static struct samsung_gpio_chip exynos4_gpios_3[] = {
 #endif
 };
 
+#if defined(CONFIG_ARCH_EXYNOS4) && defined(CONFIG_OF)
+static int exynos4_gpio_xlate(struct gpio_chip *gc, struct device_node *np,
+			      const void *gpio_spec, u32 *flags)
+{
+	const __be32 *gpio = gpio_spec;
+	const u32 n = be32_to_cpup(gpio);
+	unsigned int pin = gc->base + be32_to_cpu(gpio[0]);
+
+	if (WARN_ON(gc->of_gpio_n_cells < 4))
+		return -EINVAL;
+
+	if (n > gc->ngpio)
+		return -EINVAL;
+
+	if (s3c_gpio_cfgpin(pin, S3C_GPIO_SFN(be32_to_cpu(gpio[1]))))
+		pr_warn("gpio_xlate: failed to set pin function\n");
+	if (s3c_gpio_setpull(pin, be32_to_cpu(gpio[2])))
+		pr_warn("gpio_xlate: failed to set pin pull up/down\n");
+	if (s5p_gpio_set_drvstr(pin, be32_to_cpu(gpio[3])))
+		pr_warn("gpio_xlate: failed to set pin drive strength\n");
+
+	return n;
+}
+
+static const struct of_device_id exynos4_gpio_dt_match[] __initdata = {
+	{ .compatible = "samsung,exynos4-gpio", },
+	{}
+};
+
+static __init void exynos4_gpiolib_attach_ofnode(struct samsung_gpio_chip *chip,
+						 u64 base, u64 offset)
+{
+	struct gpio_chip *gc =  &chip->chip;
+	u64 address;
+
+	if (!of_have_populated_dt())
+		return;
+
+	address = chip->base ? base + ((u32)chip->base & 0xfff) : base + offset;
+	gc->of_node = of_find_matching_node_by_address(NULL,
+			exynos4_gpio_dt_match, address);
+	if (!gc->of_node) {
+		pr_info("gpio: device tree node not found for gpio controller"
+			" with base address %08llx\n", address);
+		return;
+	}
+	gc->of_gpio_n_cells = 4;
+	gc->of_xlate = exynos4_gpio_xlate;
+}
+#elif defined(CONFIG_ARCH_EXYNOS4)
+static __init void exynos4_gpiolib_attach_ofnode(struct samsung_gpio_chip *chip,
+						 u64 base, u64 offset)
+{
+	return;
+}
+#endif /* defined(CONFIG_ARCH_EXYNOS4) && defined(CONFIG_OF) */
+
 /* TODO: cleanup soc_is_* */
 static __init int samsung_gpiolib_init(void)
 {
@@ -2464,6 +2524,10 @@ static __init int samsung_gpiolib_init(void)
 				chip->config = &exynos4_gpio_cfg;
 				chip->group = group++;
 			}
+#ifdef CONFIG_CPU_EXYNOS4210
+			exynos4_gpiolib_attach_ofnode(chip,
+					EXYNOS4_PA_GPIO1, i * 0x20);
+#endif
 		}
 		samsung_gpiolib_add_4bit_chips(exynos4_gpios_1, nr_chips, S5P_VA_GPIO1);
 
@@ -2476,6 +2540,10 @@ static __init int samsung_gpiolib_init(void)
 				chip->config = &exynos4_gpio_cfg;
 				chip->group = group++;
 			}
+#ifdef CONFIG_CPU_EXYNOS4210
+			exynos4_gpiolib_attach_ofnode(chip,
+					EXYNOS4_PA_GPIO2, i * 0x20);
+#endif
 		}
 		samsung_gpiolib_add_4bit_chips(exynos4_gpios_2, nr_chips, S5P_VA_GPIO2);
 
@@ -2488,6 +2556,10 @@ static __init int samsung_gpiolib_init(void)
 				chip->config = &exynos4_gpio_cfg;
 				chip->group = group++;
 			}
+#ifdef CONFIG_CPU_EXYNOS4210
+			exynos4_gpiolib_attach_ofnode(chip,
+					EXYNOS4_PA_GPIO3, i * 0x20);
+#endif
 		}
 		samsung_gpiolib_add_4bit_chips(exynos4_gpios_3, nr_chips, S5P_VA_GPIO3);
 
diff --git a/drivers/gpio/gpio-u300.c b/drivers/gpio/gpio-u300.c
deleted file mode 100644
index 4035778852b0..000000000000
--- a/drivers/gpio/gpio-u300.c
+++ /dev/null
@@ -1,917 +0,0 @@
-/*
- * U300 GPIO module.
- *
- * Copyright (C) 2007-2011 ST-Ericsson AB
- * License terms: GNU General Public License (GPL) version 2
- * This can driver either of the two basic GPIO cores
- * available in the U300 platforms:
- * COH 901 335   - Used in DB3150 (U300 1.0) and DB3200 (U330 1.0)
- * COH 901 571/3 - Used in DB3210 (U365 2.0) and DB3350 (U335 1.0)
- * Author: Linus Walleij <linus.walleij@linaro.org>
- * Author: Jonas Aaberg <jonas.aberg@stericsson.com>
- */
-#include <linux/module.h>
-#include <linux/irq.h>
-#include <linux/interrupt.h>
-#include <linux/delay.h>
-#include <linux/errno.h>
-#include <linux/io.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/platform_device.h>
-#include <linux/gpio.h>
-#include <linux/list.h>
-#include <linux/slab.h>
-#include <mach/gpio-u300.h>
-
-/*
- * Bias modes for U300 GPIOs
- *
- * GPIO_U300_CONFIG_BIAS_UNKNOWN: this bias mode is not known to us
- * GPIO_U300_CONFIG_BIAS_FLOAT: no specific bias, the GPIO will float or state
- *	is not controlled by software
- * GPIO_U300_CONFIG_BIAS_PULL_UP: the GPIO will be pulled up (usually with high
- *	impedance to VDD)
- */
-#define GPIO_U300_CONFIG_BIAS_UNKNOWN	0x1000
-#define GPIO_U300_CONFIG_BIAS_FLOAT	0x1001
-#define GPIO_U300_CONFIG_BIAS_PULL_UP	0x1002
-
-/*
- * Drive modes for U300 GPIOs (output)
- *
- * GPIO_U300_CONFIG_DRIVE_PUSH_PULL: the GPIO will be driven actively high and
- *	low, this is the most typical case and is typically achieved with two
- *	active transistors on the output
- * GPIO_U300_CONFIG_DRIVE_OPEN_DRAIN: the GPIO will be driven with open drain
- *	(open collector) which means it is usually wired with other output
- *	ports which are then pulled up with an external resistor
- * GPIO_U300_CONFIG_DRIVE_OPEN_SOURCE: the GPIO will be driven with open drain
- *	(open emitter) which is the same as open drain mutatis mutandis but
- *	pulled to ground
- */
-#define GPIO_U300_CONFIG_DRIVE_PUSH_PULL	0x2000
-#define GPIO_U300_CONFIG_DRIVE_OPEN_DRAIN	0x2001
-#define GPIO_U300_CONFIG_DRIVE_OPEN_SOURCE	0x2002
-
-/*
- * Register definitions for COH 901 335 variant
- */
-#define U300_335_PORT_STRIDE				(0x1C)
-/* Port X Pin Data Register 32bit, this is both input and output (R/W) */
-#define U300_335_PXPDIR					(0x00)
-#define U300_335_PXPDOR					(0x00)
-/* Port X Pin Config Register 32bit (R/W) */
-#define U300_335_PXPCR					(0x04)
-/* This register layout is the same in both blocks */
-#define U300_GPIO_PXPCR_ALL_PINS_MODE_MASK		(0x0000FFFFUL)
-#define U300_GPIO_PXPCR_PIN_MODE_MASK			(0x00000003UL)
-#define U300_GPIO_PXPCR_PIN_MODE_SHIFT			(0x00000002UL)
-#define U300_GPIO_PXPCR_PIN_MODE_INPUT			(0x00000000UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL	(0x00000001UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN	(0x00000002UL)
-#define U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE	(0x00000003UL)
-/* Port X Interrupt Event Register 32bit (R/W) */
-#define U300_335_PXIEV					(0x08)
-/* Port X Interrupt Enable Register 32bit (R/W) */
-#define U300_335_PXIEN					(0x0C)
-/* Port X Interrupt Force Register 32bit (R/W) */
-#define U300_335_PXIFR					(0x10)
-/* Port X Interrupt Config Register 32bit (R/W) */
-#define U300_335_PXICR					(0x14)
-/* This register layout is the same in both blocks */
-#define U300_GPIO_PXICR_ALL_IRQ_CONFIG_MASK		(0x000000FFUL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_MASK			(0x00000001UL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_FALLING_EDGE		(0x00000000UL)
-#define U300_GPIO_PXICR_IRQ_CONFIG_RISING_EDGE		(0x00000001UL)
-/* Port X Pull-up Enable Register 32bit (R/W) */
-#define U300_335_PXPER					(0x18)
-/* This register layout is the same in both blocks */
-#define U300_GPIO_PXPER_ALL_PULL_UP_DISABLE_MASK	(0x000000FFUL)
-#define U300_GPIO_PXPER_PULL_UP_DISABLE			(0x00000001UL)
-/* Control Register 32bit (R/W) */
-#define U300_335_CR					(0x54)
-#define U300_335_CR_BLOCK_CLOCK_ENABLE			(0x00000001UL)
-
-/*
- * Register definitions for COH 901 571 / 3 variant
- */
-#define U300_571_PORT_STRIDE				(0x30)
-/*
- * Control Register 32bit (R/W)
- * bit 15-9 (mask 0x0000FE00) contains the number of cores. 8*cores
- * gives the number of GPIO pins.
- * bit 8-2  (mask 0x000001FC) contains the core version ID.
- */
-#define U300_571_CR					(0x00)
-#define U300_571_CR_SYNC_SEL_ENABLE			(0x00000002UL)
-#define U300_571_CR_BLOCK_CLKRQ_ENABLE			(0x00000001UL)
-/*
- * These registers have the same layout and function as the corresponding
- * COH 901 335 registers, just at different offset.
- */
-#define U300_571_PXPDIR					(0x04)
-#define U300_571_PXPDOR					(0x08)
-#define U300_571_PXPCR					(0x0C)
-#define U300_571_PXPER					(0x10)
-#define U300_571_PXIEV					(0x14)
-#define U300_571_PXIEN					(0x18)
-#define U300_571_PXIFR					(0x1C)
-#define U300_571_PXICR					(0x20)
-
-/* 8 bits per port, no version has more than 7 ports */
-#define U300_GPIO_PINS_PER_PORT 8
-#define U300_GPIO_MAX (U300_GPIO_PINS_PER_PORT * 7)
-
-struct u300_gpio {
-	struct gpio_chip chip;
-	struct list_head port_list;
-	struct clk *clk;
-	struct resource *memres;
-	void __iomem *base;
-	struct device *dev;
-	int irq_base;
-	u32 stride;
-	/* Register offsets */
-	u32 pcr;
-	u32 dor;
-	u32 dir;
-	u32 per;
-	u32 icr;
-	u32 ien;
-	u32 iev;
-};
-
-struct u300_gpio_port {
-	struct list_head node;
-	struct u300_gpio *gpio;
-	char name[8];
-	int irq;
-	int number;
-	u8 toggle_edge_mode;
-};
-
-/*
- * Macro to expand to read a specific register found in the "gpio"
- * struct. It requires the struct u300_gpio *gpio variable to exist in
- * its context. It calculates the port offset from the given pin
- * offset, muliplies by the port stride and adds the register offset
- * so it provides a pointer to the desired register.
- */
-#define U300_PIN_REG(pin, reg) \
-	(gpio->base + (pin >> 3) * gpio->stride + gpio->reg)
-
-/*
- * Provides a bitmask for a specific gpio pin inside an 8-bit GPIO
- * register.
- */
-#define U300_PIN_BIT(pin) \
-	(1 << (pin & 0x07))
-
-struct u300_gpio_confdata {
-	u16 bias_mode;
-	bool output;
-	int outval;
-};
-
-/* BS335 has seven ports of 8 bits each = GPIO pins 0..55 */
-#define BS335_GPIO_NUM_PORTS 7
-/* BS365 has five ports of 8 bits each = GPIO pins 0..39 */
-#define BS365_GPIO_NUM_PORTS 5
-
-#define U300_FLOATING_INPUT { \
-	.bias_mode = GPIO_U300_CONFIG_BIAS_FLOAT, \
-	.output = false, \
-}
-
-#define U300_PULL_UP_INPUT { \
-	.bias_mode = GPIO_U300_CONFIG_BIAS_PULL_UP, \
-	.output = false, \
-}
-
-#define U300_OUTPUT_LOW { \
-	.output = true, \
-	.outval = 0, \
-}
-
-#define U300_OUTPUT_HIGH { \
-	.output = true, \
-	.outval = 1, \
-}
-
-
-/* Initial configuration */
-static const struct __initdata u300_gpio_confdata
-bs335_gpio_config[BS335_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = {
-	/* Port 0, pins 0-7 */
-	{
-		U300_FLOATING_INPUT,
-		U300_OUTPUT_HIGH,
-		U300_FLOATING_INPUT,
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-	},
-	/* Port 1, pins 0-7 */
-	{
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-		U300_PULL_UP_INPUT,
-		U300_FLOATING_INPUT,
-		U300_OUTPUT_HIGH,
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-	},
-	/* Port 2, pins 0-7 */
-	{
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_OUTPUT_LOW,
-		U300_PULL_UP_INPUT,
-		U300_OUTPUT_LOW,
-		U300_PULL_UP_INPUT,
-	},
-	/* Port 3, pins 0-7 */
-	{
-		U300_PULL_UP_INPUT,
-		U300_OUTPUT_LOW,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-	},
-	/* Port 4, pins 0-7 */
-	{
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-	},
-	/* Port 5, pins 0-7 */
-	{
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-	},
-	/* Port 6, pind 0-7 */
-	{
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-	}
-};
-
-static const struct __initdata u300_gpio_confdata
-bs365_gpio_config[BS365_GPIO_NUM_PORTS][U300_GPIO_PINS_PER_PORT] = {
-	/* Port 0, pins 0-7 */
-	{
-		U300_FLOATING_INPUT,
-		U300_OUTPUT_LOW,
-		U300_FLOATING_INPUT,
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-		U300_PULL_UP_INPUT,
-		U300_FLOATING_INPUT,
-	},
-	/* Port 1, pins 0-7 */
-	{
-		U300_OUTPUT_LOW,
-		U300_FLOATING_INPUT,
-		U300_OUTPUT_LOW,
-		U300_FLOATING_INPUT,
-		U300_FLOATING_INPUT,
-		U300_OUTPUT_HIGH,
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-	},
-	/* Port 2, pins 0-7 */
-	{
-		U300_FLOATING_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-	},
-	/* Port 3, pins 0-7 */
-	{
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-	},
-	/* Port 4, pins 0-7 */
-	{
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		U300_PULL_UP_INPUT,
-		/* These 4 pins doesn't exist on DB3210 */
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-		U300_OUTPUT_LOW,
-	}
-};
-
-/**
- * to_u300_gpio() - get the pointer to u300_gpio
- * @chip: the gpio chip member of the structure u300_gpio
- */
-static inline struct u300_gpio *to_u300_gpio(struct gpio_chip *chip)
-{
-	return container_of(chip, struct u300_gpio, chip);
-}
-
-static int u300_gpio_get(struct gpio_chip *chip, unsigned offset)
-{
-	struct u300_gpio *gpio = to_u300_gpio(chip);
-
-	return readl(U300_PIN_REG(offset, dir)) & U300_PIN_BIT(offset);
-}
-
-static void u300_gpio_set(struct gpio_chip *chip, unsigned offset, int value)
-{
-	struct u300_gpio *gpio = to_u300_gpio(chip);
-	unsigned long flags;
-	u32 val;
-
-	local_irq_save(flags);
-
-	val = readl(U300_PIN_REG(offset, dor));
-	if (value)
-		writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, dor));
-	else
-		writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, dor));
-
-	local_irq_restore(flags);
-}
-
-static int u300_gpio_direction_input(struct gpio_chip *chip, unsigned offset)
-{
-	struct u300_gpio *gpio = to_u300_gpio(chip);
-	unsigned long flags;
-	u32 val;
-
-	local_irq_save(flags);
-	val = readl(U300_PIN_REG(offset, pcr));
-	/* Mask out this pin, note 2 bits per setting */
-	val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK << ((offset & 0x07) << 1));
-	writel(val, U300_PIN_REG(offset, pcr));
-	local_irq_restore(flags);
-	return 0;
-}
-
-static int u300_gpio_direction_output(struct gpio_chip *chip, unsigned offset,
-				      int value)
-{
-	struct u300_gpio *gpio = to_u300_gpio(chip);
-	unsigned long flags;
-	u32 oldmode;
-	u32 val;
-
-	local_irq_save(flags);
-	val = readl(U300_PIN_REG(offset, pcr));
-	/*
-	 * Drive mode must be set by the special mode set function, set
-	 * push/pull mode by default if no mode has been selected.
-	 */
-	oldmode = val & (U300_GPIO_PXPCR_PIN_MODE_MASK <<
-			 ((offset & 0x07) << 1));
-	/* mode = 0 means input, else some mode is already set */
-	if (oldmode == 0) {
-		val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK <<
-			 ((offset & 0x07) << 1));
-		val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL
-			<< ((offset & 0x07) << 1));
-		writel(val, U300_PIN_REG(offset, pcr));
-	}
-	u300_gpio_set(chip, offset, value);
-	local_irq_restore(flags);
-	return 0;
-}
-
-static int u300_gpio_to_irq(struct gpio_chip *chip, unsigned offset)
-{
-	struct u300_gpio *gpio = to_u300_gpio(chip);
-	int retirq = gpio->irq_base + offset;
-
-	dev_dbg(gpio->dev, "request IRQ for GPIO %d, return %d\n", offset,
-		retirq);
-	return retirq;
-}
-
-static int u300_gpio_config(struct gpio_chip *chip, unsigned offset,
-		     u16 param, unsigned long *data)
-{
-	struct u300_gpio *gpio = to_u300_gpio(chip);
-	unsigned long flags;
-	u32 val;
-
-	local_irq_save(flags);
-	switch (param) {
-	case GPIO_U300_CONFIG_BIAS_UNKNOWN:
-	case GPIO_U300_CONFIG_BIAS_FLOAT:
-		val = readl(U300_PIN_REG(offset, per));
-		writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, per));
-		break;
-	case GPIO_U300_CONFIG_BIAS_PULL_UP:
-		val = readl(U300_PIN_REG(offset, per));
-		writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, per));
-		break;
-	case GPIO_U300_CONFIG_DRIVE_PUSH_PULL:
-		val = readl(U300_PIN_REG(offset, pcr));
-		val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
-			 << ((offset & 0x07) << 1));
-		val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_PUSH_PULL
-			<< ((offset & 0x07) << 1));
-		writel(val, U300_PIN_REG(offset, pcr));
-		break;
-	case GPIO_U300_CONFIG_DRIVE_OPEN_DRAIN:
-		val = readl(U300_PIN_REG(offset, pcr));
-		val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
-			 << ((offset & 0x07) << 1));
-		val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_DRAIN
-			<< ((offset & 0x07) << 1));
-		writel(val, U300_PIN_REG(offset, pcr));
-		break;
-	case GPIO_U300_CONFIG_DRIVE_OPEN_SOURCE:
-		val = readl(U300_PIN_REG(offset, pcr));
-		val &= ~(U300_GPIO_PXPCR_PIN_MODE_MASK
-			 << ((offset & 0x07) << 1));
-		val |= (U300_GPIO_PXPCR_PIN_MODE_OUTPUT_OPEN_SOURCE
-			<< ((offset & 0x07) << 1));
-		writel(val, U300_PIN_REG(offset, pcr));
-		break;
-	default:
-		local_irq_restore(flags);
-		dev_err(gpio->dev, "illegal configuration requested\n");
-		return -EINVAL;
-	}
-	local_irq_restore(flags);
-	return 0;
-}
-
-static struct gpio_chip u300_gpio_chip = {
-	.label			= "u300-gpio-chip",
-	.owner			= THIS_MODULE,
-	.get			= u300_gpio_get,
-	.set			= u300_gpio_set,
-	.direction_input	= u300_gpio_direction_input,
-	.direction_output	= u300_gpio_direction_output,
-	.to_irq			= u300_gpio_to_irq,
-};
-
-static void u300_toggle_trigger(struct u300_gpio *gpio, unsigned offset)
-{
-	u32 val;
-
-	val = readl(U300_PIN_REG(offset, icr));
-	/* Set mode depending on state */
-	if (u300_gpio_get(&gpio->chip, offset)) {
-		/* High now, let's trigger on falling edge next then */
-		writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
-		dev_dbg(gpio->dev, "next IRQ on falling edge on pin %d\n",
-			offset);
-	} else {
-		/* Low now, let's trigger on rising edge next then */
-		writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
-		dev_dbg(gpio->dev, "next IRQ on rising edge on pin %d\n",
-			offset);
-	}
-}
-
-static int u300_gpio_irq_type(struct irq_data *d, unsigned trigger)
-{
-	struct u300_gpio_port *port = irq_data_get_irq_chip_data(d);
-	struct u300_gpio *gpio = port->gpio;
-	int offset = d->irq - gpio->irq_base;
-	u32 val;
-
-	if ((trigger & IRQF_TRIGGER_RISING) &&
-	    (trigger & IRQF_TRIGGER_FALLING)) {
-		/*
-		 * The GPIO block can only trigger on falling OR rising edges,
-		 * not both. So we need to toggle the mode whenever the pin
-		 * goes from one state to the other with a special state flag
-		 */
-		dev_dbg(gpio->dev,
-			"trigger on both rising and falling edge on pin %d\n",
-			offset);
-		port->toggle_edge_mode |= U300_PIN_BIT(offset);
-		u300_toggle_trigger(gpio, offset);
-	} else if (trigger & IRQF_TRIGGER_RISING) {
-		dev_dbg(gpio->dev, "trigger on rising edge on pin %d\n",
-			offset);
-		val = readl(U300_PIN_REG(offset, icr));
-		writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
-		port->toggle_edge_mode &= ~U300_PIN_BIT(offset);
-	} else if (trigger & IRQF_TRIGGER_FALLING) {
-		dev_dbg(gpio->dev, "trigger on falling edge on pin %d\n",
-			offset);
-		val = readl(U300_PIN_REG(offset, icr));
-		writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, icr));
-		port->toggle_edge_mode &= ~U300_PIN_BIT(offset);
-	}
-
-	return 0;
-}
-
-static void u300_gpio_irq_enable(struct irq_data *d)
-{
-	struct u300_gpio_port *port = irq_data_get_irq_chip_data(d);
-	struct u300_gpio *gpio = port->gpio;
-	int offset = d->irq - gpio->irq_base;
-	u32 val;
-	unsigned long flags;
-
-	local_irq_save(flags);
-	val = readl(U300_PIN_REG(offset, ien));
-	writel(val | U300_PIN_BIT(offset), U300_PIN_REG(offset, ien));
-	local_irq_restore(flags);
-}
-
-static void u300_gpio_irq_disable(struct irq_data *d)
-{
-	struct u300_gpio_port *port = irq_data_get_irq_chip_data(d);
-	struct u300_gpio *gpio = port->gpio;
-	int offset = d->irq - gpio->irq_base;
-	u32 val;
-	unsigned long flags;
-
-	local_irq_save(flags);
-	val = readl(U300_PIN_REG(offset, ien));
-	writel(val & ~U300_PIN_BIT(offset), U300_PIN_REG(offset, ien));
-	local_irq_restore(flags);
-}
-
-static struct irq_chip u300_gpio_irqchip = {
-	.name			= "u300-gpio-irqchip",
-	.irq_enable		= u300_gpio_irq_enable,
-	.irq_disable		= u300_gpio_irq_disable,
-	.irq_set_type		= u300_gpio_irq_type,
-
-};
-
-static void u300_gpio_irq_handler(unsigned irq, struct irq_desc *desc)
-{
-	struct u300_gpio_port *port = irq_get_handler_data(irq);
-	struct u300_gpio *gpio = port->gpio;
-	int pinoffset = port->number << 3; /* get the right stride */
-	unsigned long val;
-
-	desc->irq_data.chip->irq_ack(&desc->irq_data);
-	/* Read event register */
-	val = readl(U300_PIN_REG(pinoffset, iev));
-	/* Mask relevant bits */
-	val &= 0xFFU; /* 8 bits per port */
-	/* ACK IRQ (clear event) */
-	writel(val, U300_PIN_REG(pinoffset, iev));
-
-	/* Call IRQ handler */
-	if (val != 0) {
-		int irqoffset;
-
-		for_each_set_bit(irqoffset, &val, U300_GPIO_PINS_PER_PORT) {
-			int pin_irq = gpio->irq_base + (port->number << 3)
-				+ irqoffset;
-			int offset = pinoffset + irqoffset;
-
-			dev_dbg(gpio->dev, "GPIO IRQ %d on pin %d\n",
-				pin_irq, offset);
-			generic_handle_irq(pin_irq);
-			/*
-			 * Triggering IRQ on both rising and falling edge
-			 * needs mockery
-			 */
-			if (port->toggle_edge_mode & U300_PIN_BIT(offset))
-				u300_toggle_trigger(gpio, offset);
-		}
-	}
-
-	desc->irq_data.chip->irq_unmask(&desc->irq_data);
-}
-
-static void __init u300_gpio_init_pin(struct u300_gpio *gpio,
-				      int offset,
-				      const struct u300_gpio_confdata *conf)
-{
-	/* Set mode: input or output */
-	if (conf->output) {
-		u300_gpio_direction_output(&gpio->chip, offset, conf->outval);
-
-		/* Deactivate bias mode for output */
-		u300_gpio_config(&gpio->chip, offset,
-				 GPIO_U300_CONFIG_BIAS_FLOAT,
-				 NULL);
-
-		/* Set drive mode for output */
-		u300_gpio_config(&gpio->chip, offset,
-				 GPIO_U300_CONFIG_DRIVE_PUSH_PULL, NULL);
-
-		dev_dbg(gpio->dev, "set up pin %d as output, value: %d\n",
-			offset, conf->outval);
-	} else {
-		u300_gpio_direction_input(&gpio->chip, offset);
-
-		/* Always set output low on input pins */
-		u300_gpio_set(&gpio->chip, offset, 0);
-
-		/* Set bias mode for input */
-		u300_gpio_config(&gpio->chip, offset, conf->bias_mode, NULL);
-
-		dev_dbg(gpio->dev, "set up pin %d as input, bias: %04x\n",
-			offset, conf->bias_mode);
-	}
-}
-
-static void __init u300_gpio_init_coh901571(struct u300_gpio *gpio,
-				     struct u300_gpio_platform *plat)
-{
-	int i, j;
-
-	/* Write default config and values to all pins */
-	for (i = 0; i < plat->ports; i++) {
-		for (j = 0; j < 8; j++) {
-			const struct u300_gpio_confdata *conf;
-			int offset = (i*8) + j;
-
-			if (plat->variant == U300_GPIO_COH901571_3_BS335)
-				conf = &bs335_gpio_config[i][j];
-			else if (plat->variant == U300_GPIO_COH901571_3_BS365)
-				conf = &bs365_gpio_config[i][j];
-			else
-				break;
-
-			u300_gpio_init_pin(gpio, offset, conf);
-		}
-	}
-}
-
-static inline void u300_gpio_free_ports(struct u300_gpio *gpio)
-{
-	struct u300_gpio_port *port;
-	struct list_head *p, *n;
-
-	list_for_each_safe(p, n, &gpio->port_list) {
-		port = list_entry(p, struct u300_gpio_port, node);
-		list_del(&port->node);
-		free_irq(port->irq, port);
-		kfree(port);
-	}
-}
-
-static int __init u300_gpio_probe(struct platform_device *pdev)
-{
-	struct u300_gpio_platform *plat = dev_get_platdata(&pdev->dev);
-	struct u300_gpio *gpio;
-	int err = 0;
-	int portno;
-	u32 val;
-	u32 ifr;
-	int i;
-
-	gpio = kzalloc(sizeof(struct u300_gpio), GFP_KERNEL);
-	if (gpio == NULL) {
-		dev_err(&pdev->dev, "failed to allocate memory\n");
-		return -ENOMEM;
-	}
-
-	gpio->chip = u300_gpio_chip;
-	gpio->chip.ngpio = plat->ports * U300_GPIO_PINS_PER_PORT;
-	gpio->irq_base = plat->gpio_irq_base;
-	gpio->chip.dev = &pdev->dev;
-	gpio->chip.base = plat->gpio_base;
-	gpio->dev = &pdev->dev;
-
-	/* Get GPIO clock */
-	gpio->clk = clk_get(gpio->dev, NULL);
-	if (IS_ERR(gpio->clk)) {
-		err = PTR_ERR(gpio->clk);
-		dev_err(gpio->dev, "could not get GPIO clock\n");
-		goto err_no_clk;
-	}
-	err = clk_enable(gpio->clk);
-	if (err) {
-		dev_err(gpio->dev, "could not enable GPIO clock\n");
-		goto err_no_clk_enable;
-	}
-
-	gpio->memres = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	if (!gpio->memres) {
-		dev_err(gpio->dev, "could not get GPIO memory resource\n");
-		err = -ENODEV;
-		goto err_no_resource;
-	}
-
-	if (!request_mem_region(gpio->memres->start,
-				resource_size(gpio->memres),
-				"GPIO Controller")) {
-		err = -ENODEV;
-		goto err_no_ioregion;
-	}
-
-	gpio->base = ioremap(gpio->memres->start, resource_size(gpio->memres));
-	if (!gpio->base) {
-		err = -ENOMEM;
-		goto err_no_ioremap;
-	}
-
-	if (plat->variant == U300_GPIO_COH901335) {
-		dev_info(gpio->dev,
-			 "initializing GPIO Controller COH 901 335\n");
-		gpio->stride = U300_335_PORT_STRIDE;
-		gpio->pcr = U300_335_PXPCR;
-		gpio->dor = U300_335_PXPDOR;
-		gpio->dir = U300_335_PXPDIR;
-		gpio->per = U300_335_PXPER;
-		gpio->icr = U300_335_PXICR;
-		gpio->ien = U300_335_PXIEN;
-		gpio->iev = U300_335_PXIEV;
-		ifr = U300_335_PXIFR;
-
-		/* Turn on the GPIO block */
-		writel(U300_335_CR_BLOCK_CLOCK_ENABLE,
-		       gpio->base + U300_335_CR);
-	} else if (plat->variant == U300_GPIO_COH901571_3_BS335 ||
-		   plat->variant == U300_GPIO_COH901571_3_BS365) {
-		dev_info(gpio->dev,
-			 "initializing GPIO Controller COH 901 571/3\n");
-		gpio->stride = U300_571_PORT_STRIDE;
-		gpio->pcr = U300_571_PXPCR;
-		gpio->dor = U300_571_PXPDOR;
-		gpio->dir = U300_571_PXPDIR;
-		gpio->per = U300_571_PXPER;
-		gpio->icr = U300_571_PXICR;
-		gpio->ien = U300_571_PXIEN;
-		gpio->iev = U300_571_PXIEV;
-		ifr = U300_571_PXIFR;
-
-		val = readl(gpio->base + U300_571_CR);
-		dev_info(gpio->dev, "COH901571/3 block version: %d, " \
-			 "number of cores: %d totalling %d pins\n",
-			 ((val & 0x000001FC) >> 2),
-			 ((val & 0x0000FE00) >> 9),
-			 ((val & 0x0000FE00) >> 9) * 8);
-		writel(U300_571_CR_BLOCK_CLKRQ_ENABLE,
-		       gpio->base + U300_571_CR);
-		u300_gpio_init_coh901571(gpio, plat);
-	} else {
-		dev_err(gpio->dev, "unknown block variant\n");
-		err = -ENODEV;
-		goto err_unknown_variant;
-	}
-
-	/* Add each port with its IRQ separately */
-	INIT_LIST_HEAD(&gpio->port_list);
-	for (portno = 0 ; portno < plat->ports; portno++) {
-		struct u300_gpio_port *port =
-			kmalloc(sizeof(struct u300_gpio_port), GFP_KERNEL);
-
-		if (!port) {
-			dev_err(gpio->dev, "out of memory\n");
-			err = -ENOMEM;
-			goto err_no_port;
-		}
-
-		snprintf(port->name, 8, "gpio%d", portno);
-		port->number = portno;
-		port->gpio = gpio;
-
-		port->irq = platform_get_irq_byname(pdev,
-						    port->name);
-
-		dev_dbg(gpio->dev, "register IRQ %d for %s\n", port->irq,
-			port->name);
-
-		irq_set_chained_handler(port->irq, u300_gpio_irq_handler);
-		irq_set_handler_data(port->irq, port);
-
-		/* For each GPIO pin set the unique IRQ handler */
-		for (i = 0; i < U300_GPIO_PINS_PER_PORT; i++) {
-			int irqno = gpio->irq_base + (portno << 3) + i;
-
-			dev_dbg(gpio->dev, "handler for IRQ %d on %s\n",
-				irqno, port->name);
-			irq_set_chip_and_handler(irqno, &u300_gpio_irqchip,
-						 handle_simple_irq);
-			set_irq_flags(irqno, IRQF_VALID);
-			irq_set_chip_data(irqno, port);
-		}
-
-		/* Turns off irq force (test register) for this port */
-		writel(0x0, gpio->base + portno * gpio->stride + ifr);
-
-		list_add_tail(&port->node, &gpio->port_list);
-	}
-	dev_dbg(gpio->dev, "initialized %d GPIO ports\n", portno);
-
-	err = gpiochip_add(&gpio->chip);
-	if (err) {
-		dev_err(gpio->dev, "unable to add gpiochip: %d\n", err);
-		goto err_no_chip;
-	}
-
-	platform_set_drvdata(pdev, gpio);
-
-	return 0;
-
-err_no_chip:
-err_no_port:
-	u300_gpio_free_ports(gpio);
-err_unknown_variant:
-	iounmap(gpio->base);
-err_no_ioremap:
-	release_mem_region(gpio->memres->start, resource_size(gpio->memres));
-err_no_ioregion:
-err_no_resource:
-	clk_disable(gpio->clk);
-err_no_clk_enable:
-	clk_put(gpio->clk);
-err_no_clk:
-	kfree(gpio);
-	dev_info(&pdev->dev, "module ERROR:%d\n", err);
-	return err;
-}
-
-static int __exit u300_gpio_remove(struct platform_device *pdev)
-{
-	struct u300_gpio_platform *plat = dev_get_platdata(&pdev->dev);
-	struct u300_gpio *gpio = platform_get_drvdata(pdev);
-	int err;
-
-	/* Turn off the GPIO block */
-	if (plat->variant == U300_GPIO_COH901335)
-		writel(0x00000000U, gpio->base + U300_335_CR);
-	if (plat->variant == U300_GPIO_COH901571_3_BS335 ||
-	    plat->variant == U300_GPIO_COH901571_3_BS365)
-		writel(0x00000000U, gpio->base + U300_571_CR);
-
-	err = gpiochip_remove(&gpio->chip);
-	if (err < 0) {
-		dev_err(gpio->dev, "unable to remove gpiochip: %d\n", err);
-		return err;
-	}
-	u300_gpio_free_ports(gpio);
-	iounmap(gpio->base);
-	release_mem_region(gpio->memres->start,
-			   resource_size(gpio->memres));
-	clk_disable(gpio->clk);
-	clk_put(gpio->clk);
-	platform_set_drvdata(pdev, NULL);
-	kfree(gpio);
-	return 0;
-}
-
-static struct platform_driver u300_gpio_driver = {
-	.driver		= {
-		.name	= "u300-gpio",
-	},
-	.remove		= __exit_p(u300_gpio_remove),
-};
-
-
-static int __init u300_gpio_init(void)
-{
-	return platform_driver_probe(&u300_gpio_driver, u300_gpio_probe);
-}
-
-static void __exit u300_gpio_exit(void)
-{
-	platform_driver_unregister(&u300_gpio_driver);
-}
-
-arch_initcall(u300_gpio_init);
-module_exit(u300_gpio_exit);
-
-MODULE_AUTHOR("Linus Walleij <linus.walleij@stericsson.com>");
-MODULE_DESCRIPTION("ST-Ericsson AB COH 901 335/COH 901 571/3 GPIO driver");
-MODULE_LICENSE("GPL");