MIPS: Alchemy: merge devboard code into single per-board files.

Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2884/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

1 files changed, 167 insertions, 0 deletions

diff --git a/arch/mips/alchemy/devboards/pb1100.c b/arch/mips/alchemy/devboards/pb1100.c
new file mode 100644
index 000000000000..cff50d05ddd4
--- /dev/null
+++ b/arch/mips/alchemy/devboards/pb1100.c
@@ -0,0 +1,167 @@
+/*
+ * Pb1100 board platform device registration
+ *
+ * Copyright (C) 2009 Manuel Lauss
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
+ */
+
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/dma-mapping.h>
+#include <linux/platform_device.h>
+#include <asm/mach-au1x00/au1000.h>
+#include <asm/mach-db1x00/bcsr.h>
+#include <prom.h>
+#include "platform.h"
+
+const char *get_system_type(void)
+{
+	return "PB1100";
+}
+
+void __init board_setup(void)
+{
+	volatile void __iomem *base = (volatile void __iomem *)0xac000000UL;
+
+	bcsr_init(DB1000_BCSR_PHYS_ADDR,
+		  DB1000_BCSR_PHYS_ADDR + DB1000_BCSR_HEXLED_OFS);
+
+	/* Set AUX clock to 12 MHz * 8 = 96 MHz */
+	au_writel(8, SYS_AUXPLL);
+	alchemy_gpio1_input_enable();
+	udelay(100);
+
+#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+	{
+		u32 pin_func, sys_freqctrl, sys_clksrc;
+
+		/* Configure pins GPIO[14:9] as GPIO */
+		pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_UR3;
+
+		/* Zero and disable FREQ2 */
+		sys_freqctrl = au_readl(SYS_FREQCTRL0);
+		sys_freqctrl &= ~0xFFF00000;
+		au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+		/* Zero and disable USBH/USBD/IrDA clock */
+		sys_clksrc = au_readl(SYS_CLKSRC);
+		sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
+		au_writel(sys_clksrc, SYS_CLKSRC);
+
+		sys_freqctrl = au_readl(SYS_FREQCTRL0);
+		sys_freqctrl &= ~0xFFF00000;
+
+		sys_clksrc = au_readl(SYS_CLKSRC);
+		sys_clksrc &= ~(SYS_CS_CIR | SYS_CS_DIR | SYS_CS_MIR_MASK);
+
+		/* FREQ2 = aux / 2 = 48 MHz */
+		sys_freqctrl |= (0 << SYS_FC_FRDIV2_BIT) |
+				SYS_FC_FE2 | SYS_FC_FS2;
+		au_writel(sys_freqctrl, SYS_FREQCTRL0);
+
+		/*
+		 * Route 48 MHz FREQ2 into USBH/USBD/IrDA
+		 */
+		sys_clksrc |= SYS_CS_MUX_FQ2 << SYS_CS_MIR_BIT;
+		au_writel(sys_clksrc, SYS_CLKSRC);
+
+		/* Setup the static bus controller */
+		au_writel(0x00000002, MEM_STCFG3);  /* type = PCMCIA */
+		au_writel(0x280E3D07, MEM_STTIME3); /* 250ns cycle time */
+		au_writel(0x10000000, MEM_STADDR3); /* any PCMCIA select */
+
+		/*
+		 * Get USB Functionality pin state (device vs host drive pins).
+		 */
+		pin_func = au_readl(SYS_PINFUNC) & ~SYS_PF_USB;
+		/* 2nd USB port is USB host. */
+		pin_func |= SYS_PF_USB;
+		au_writel(pin_func, SYS_PINFUNC);
+	}
+#endif /* defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE) */
+
+	/* Enable sys bus clock divider when IDLE state or no bus activity. */
+	au_writel(au_readl(SYS_POWERCTRL) | (0x3 << 5), SYS_POWERCTRL);
+
+	/* Enable the RTC if not already enabled. */
+	if (!(readb(base + 0x28) & 0x20)) {
+		writeb(readb(base + 0x28) | 0x20, base + 0x28);
+		au_sync();
+	}
+	/* Put the clock in BCD mode. */
+	if (readb(base + 0x2C) & 0x4) { /* reg B */
+		writeb(readb(base + 0x2c) & ~0x4, base + 0x2c);
+		au_sync();
+	}
+}
+
+/******************************************************************************/
+
+static struct resource au1100_lcd_resources[] = {
+	[0] = {
+		.start	= AU1100_LCD_PHYS_ADDR,
+		.end	= AU1100_LCD_PHYS_ADDR + 0x800 - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AU1100_LCD_INT,
+		.end	= AU1100_LCD_INT,
+		.flags	= IORESOURCE_IRQ,
+	}
+};
+
+static u64 au1100_lcd_dmamask = DMA_BIT_MASK(32);
+
+static struct platform_device au1100_lcd_device = {
+	.name		= "au1100-lcd",
+	.id		= 0,
+	.dev = {
+		.dma_mask		= &au1100_lcd_dmamask,
+		.coherent_dma_mask	= DMA_BIT_MASK(32),
+	},
+	.num_resources	= ARRAY_SIZE(au1100_lcd_resources),
+	.resource	= au1100_lcd_resources,
+};
+
+static int __init pb1100_dev_init(void)
+{
+	int swapped;
+
+	irq_set_irq_type(AU1100_GPIO9_INT, IRQF_TRIGGER_LOW); /* PCCD# */
+	irq_set_irq_type(AU1100_GPIO10_INT, IRQF_TRIGGER_LOW); /* PCSTSCHG# */
+	irq_set_irq_type(AU1100_GPIO11_INT, IRQF_TRIGGER_LOW); /* PCCard# */
+	irq_set_irq_type(AU1100_GPIO13_INT, IRQF_TRIGGER_LOW); /* DC_IRQ# */
+
+	/* PCMCIA. single socket, identical to Pb1500 */
+	db1x_register_pcmcia_socket(
+		AU1000_PCMCIA_ATTR_PHYS_ADDR,
+		AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
+		AU1000_PCMCIA_MEM_PHYS_ADDR,
+		AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,
+		AU1000_PCMCIA_IO_PHYS_ADDR,
+		AU1000_PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,
+		AU1100_GPIO11_INT, AU1100_GPIO9_INT,	 /* card / insert */
+		/*AU1100_GPIO10_INT*/0, 0, 0); /* stschg / eject / id */
+
+	swapped = bcsr_read(BCSR_STATUS) &  BCSR_STATUS_DB1000_SWAPBOOT;
+	db1x_register_norflash(64 * 1024 * 1024, 4, swapped);
+	platform_device_register(&au1100_lcd_device);
+
+	return 0;
+}
+device_initcall(pb1100_dev_init);