ALSA: multisound.sh: update module namespace

The modules for the cards described here changed their names.
Update accordingly.

Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>

1 files changed, 36 insertions, 36 deletions

diff --git a/Documentation/sound/cards/multisound.sh b/Documentation/sound/cards/multisound.sh
index 0e0cb029421b..a915a1affcde 100755
--- a/Documentation/sound/cards/multisound.sh
+++ b/Documentation/sound/cards/multisound.sh
@@ -34,12 +34,12 @@
 #  composed of the following modules (these can also operate compiled
 #  into the kernel):
 #
-#  msnd               - MultiSound base (requires soundcore)
+#  snd-msnd-lib           - MultiSound base (requires snd)
 #
-#  msnd_classic       - Base audio/mixer support for Classic, Monetery and
-#                       Tahiti cards
+#  snd-msnd-classic       - Base audio/mixer support for Classic, Monetery and
+#                           Tahiti cards
 #
-#  msnd_pinnacle      - Base audio/mixer support for Pinnacle and Fiji cards
+#  snd-msnd-pinnacle      - Base audio/mixer support for Pinnacle and Fiji cards
 #
 #
 #  Important Notes - Read Before Using
@@ -66,7 +66,7 @@
 #
 #  * Classic/Monterey/Tahiti
 #
-#  These cards are configured through the driver msnd_classic.  You must
+#  These cards are configured through the driver snd-msnd-classic.  You must
 #  know the io port, then the driver will select the irq and memory resources
 #  on the card.  It is up to you to know if these are free locations or now,
 #  a conflict can lock the machine up.
@@ -81,10 +81,10 @@
 #  can be used to configure the card in non-PnP mode, and in PnP mode
 #  you can use isapnptools.  These are described briefly here.
 #
-#  pinnaclecfg is not required; you can use the msnd_pinnacle module
+#  pinnaclecfg is not required; you can use the snd-msnd-pinnacle module
 #  to fully configure the card as well.  However, pinnaclecfg can be
 #  used to change the resource values of a particular device after the
-#  msnd_pinnacle module has been loaded.  If you are compiling the
+#  snd-msnd-pinnacle module has been loaded.  If you are compiling the
 #  driver into the kernel, you must set these values during compile
 #  time, however other peripheral resource values can be changed with
 #  the pinnaclecfg program after the kernel is loaded.
@@ -96,7 +96,7 @@
 #  to obtain one with the command `pnpdump 1 0x203' -- this may vary
 #  for you (running pnpdump by itself did not work for me).  Then,
 #  edit this file and use isapnp to uncomment and set the card values.
-#  Use these values when inserting the msnd_pinnacle module.  Using
+#  Use these values when inserting the snd-msnd-pinnacle module.  Using
 #  this method, you can set the resources for the DSP and the Kurzweil
 #  synth (Pinnacle).  Since Linux does not directly support PnP
 #  devices, you may have difficulty when using the card in PnP mode
@@ -133,16 +133,16 @@
 #  pinnaclecfg program.  Using this program, you can assign the
 #  resource values to the card's devices, or disable the devices.  As
 #  an alternative to using pinnaclecfg, you can specify many of the
-#  configuration values when loading the msnd_pinnacle module (or
+#  configuration values when loading the snd-msnd-pinnacle module (or
 #  during kernel configuration when compiling the driver into the
 #  kernel).
 #
-#  If you specify cfg=0x250 for the msnd_pinnacle module, it
+#  If you specify cfg=0x250 for the snd-msnd-pinnacle module, it
 #  automatically configure the card to the given io, irq and memory
 #  values using that config port (the config port is jumper selectable
 #  on the card to 0x250, 0x260 or 0x270).
 #
-#  See the `msnd_pinnacle Additional Options' section below for more
+#  See the `snd-msnd-pinnacle Additional Options' section below for more
 #  information on these parameters (also, if you compile the driver
 #  directly into the kernel, these extra parameters can be useful
 #  here).
@@ -157,44 +157,44 @@
 #
 #  * MultiSound Classic/Monterey/Tahiti:
 #
-#  modprobe soundcore
-#  insmod msnd
-#  insmod msnd_classic io=0x290 irq=7 mem=0xd0000
+#  modprobe snd
+#  insmod snd-msnd-lib
+#  insmod snd-msnd-classic io=0x290 irq=7 mem=0xd0000
 #
 #  * MultiSound Pinnacle in PnP mode:
 #
-#  modprobe soundcore
-#  insmod msnd
+#  modprobe snd
+#  insmod snd-msnd-lib
 #  isapnp mypinnacle.conf
-#  insmod msnd_pinnacle io=0x210 irq=5 mem=0xd8000 <-- match mypinnacle.conf values
+#  insmod snd-msnd-pinnacle io=0x210 irq=5 mem=0xd8000 <-- match mypinnacle.conf values
 #
 #  * MultiSound Pinnacle in non-PnP mode (replace 0x250 with your configuration port,
 #    one of 0x250, 0x260 or 0x270):
 #
-#  insmod soundcore
-#  insmod msnd
-#  insmod msnd_pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000
+#  modprobe snd
+#  insmod snd-msnd-lib
+#  insmod snd-msnd-pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000
 #
 # * To use the MPU-compatible Kurzweil synth on the Pinnacle in PnP
 #   mode, add the following (assumes you did `isapnp mypinnacle.conf'):
 #
-#  insmod sound
+#  insmod snd
 #  insmod mpu401 io=0x330 irq=9                    <-- match mypinnacle.conf values
 #
 # * To use the MPU-compatible Kurzweil synth on the Pinnacle in non-PnP
 #   mode, add the following.  Note how we first configure the peripheral's
 #   resources, _then_ install a Linux driver for it:
 #
-#  insmod sound
+#  insmod snd
 #  pinnaclecfg 0x250 mpu 0x330 9
 #  insmod mpu401 io=0x330 irq=9
 #
 #  -- OR you can use the following sequence without pinnaclecfg in non-PnP mode:
 #
-#  insmod soundcore
-#  insmod msnd
-#  insmod msnd_pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 mpu_io=0x330 mpu_irq=9
-#  insmod sound
+#  modprobe snd
+#  insmod snd-msnd-lib
+#  insmod snd-msnd-pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 mpu_io=0x330 mpu_irq=9
+#  insmod snd
 #  insmod mpu401 io=0x330 irq=9
 #
 # * To setup the joystick port on the Pinnacle in non-PnP mode (though
@@ -203,15 +203,15 @@
 #
 #   pinnaclecfg 0x250 joystick 0x200
 #
-#  -- OR you can configure this using msnd_pinnacle with the following:
+#  -- OR you can configure this using snd-msnd-pinnacle with the following:
 #
-#  insmod soundcore
-#  insmod msnd
-#  insmod msnd_pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 joystick_io=0x200
+#  modprobe snd
+#  insmod snd-msnd-lib
+#  insmod snd-msnd-pinnacle cfg=0x250 io=0x290 irq=5 mem=0xd0000 joystick_io=0x200
 #
 #
-#  msnd_classic, msnd_pinnacle Required Options
-#  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+#  snd-msnd-classic, snd-msnd-pinnacle Required Options
+#  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 #
 #  If the following options are not given, the module will not load.
 #  Examine the kernel message log for informative error messages.
@@ -223,8 +223,8 @@
 #  mem                  Shared memory area, e.g. mem=0xd8000
 #
 #
-#  msnd_classic, msnd_pinnacle Additional Options
-#  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+#  snd-msnd-classic, snd-msnd-pinnacle Additional Options
+#  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 #
 #  fifosize             The digital audio FIFOs, in kilobytes.  If not
 #                       specified, the default will be used.  Increasing
@@ -244,8 +244,8 @@
 #                       to zero).
 #
 #
-#  msnd_pinnacle Additional Options
-#  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
+#  snd-msnd-pinnacle Additional Options
+#  ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
 #
 #  digital              Specify digital=1 to enable the S/PDIF input
 #                       if you have the digital daughterboard