Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC platform changes from Olof Johansson:
 "This branch contains mostly additions and changes to platform
  enablement and SoC-level drivers.  Since there's sometimes a
  dependency on device-tree changes, there's also a fair amount of
  those in this branch.

  Pieces worth mentioning are:

   - Mbus driver for Marvell platforms, allowing kernel configuration
     and resource allocation of on-chip peripherals.
   - Enablement of the mbus infrastructure from Marvell PCI-e drivers.
   - Preparation of MSI support for Marvell platforms.
   - Addition of new PCI-e host controller driver for Tegra platforms
   - Some churn caused by sharing of macro names between i.MX 6Q and 6DL
     platforms in the device tree sources and header files.
   - Various suspend/PM updates for Tegra, including LP1 support.
   - Versatile Express support for MCPM, part of big little support.
   - Allwinner platform support for A20 and A31 SoCs (dual and quad
     Cortex-A7)
   - OMAP2+ support for DRA7, a new Cortex-A15-based SoC.

  The code that touches other architectures are patches moving MSI
  arch-specific functions over to weak symbols and removal of
  ARCH_SUPPORTS_MSI, acked by PCI maintainers"

* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (266 commits)
  tegra-cpuidle: provide stub when !CONFIG_CPU_IDLE
  PCI: tegra: replace devm_request_and_ioremap by devm_ioremap_resource
  ARM: tegra: Drop ARCH_SUPPORTS_MSI and sort list
  ARM: dts: vf610-twr: enable i2c0 device
  ARM: dts: i.MX51: Add one more I2C2 pinmux entry
  ARM: dts: i.MX51: Move pins configuration under "iomuxc" label
  ARM: dtsi: imx6qdl-sabresd: Add USB OTG vbus pin to pinctrl_hog
  ARM: dtsi: imx6qdl-sabresd: Add USB host 1 VBUS regulator
  ARM: dts: imx27-phytec-phycore-som: Enable AUDMUX
  ARM: dts: i.MX27: Disable AUDMUX in the template
  ARM: dts: wandboard: Add support for SDIO bcm4329
  ARM: i.MX5 clocks: Remove optional clock setup (CKIH1) from i.MX51 template
  ARM: dts: imx53-qsb: Make USBH1 functional
  ARM i.MX6Q: dts: Enable I2C1 with EEPROM and PMIC on Phytec phyFLEX-i.MX6 Ouad module
  ARM i.MX6Q: dts: Enable SPI NOR flash on Phytec phyFLEX-i.MX6 Ouad module
  ARM: dts: imx6qdl-sabresd: Add touchscreen support
  ARM: imx: add ocram clock for imx53
  ARM: dts: imx: ocram size is different between imx6q and imx6dl
  ARM: dts: imx27-phytec-phycore-som: Fix regulator settings
  ARM: dts: i.MX27: Remove clock name from CPU node
  ...

1 files changed, 163 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt
new file mode 100644
index 000000000000..6b7510775c50
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt
@@ -0,0 +1,163 @@
+NVIDIA Tegra PCIe controller
+
+Required properties:
+- compatible: "nvidia,tegra20-pcie" or "nvidia,tegra30-pcie"
+- device_type: Must be "pci"
+- reg: A list of physical base address and length for each set of controller
+  registers. Must contain an entry for each entry in the reg-names property.
+- reg-names: Must include the following entries:
+  "pads": PADS registers
+  "afi": AFI registers
+  "cs": configuration space region
+- interrupts: A list of interrupt outputs of the controller. Must contain an
+  entry for each entry in the interrupt-names property.
+- interrupt-names: Must include the following entries:
+  "intr": The Tegra interrupt that is asserted for controller interrupts
+  "msi": The Tegra interrupt that is asserted when an MSI is received
+- pex-clk-supply: Supply voltage for internal reference clock
+- vdd-supply: Power supply for controller (1.05V)
+- avdd-supply: Power supply for controller (1.05V) (not required for Tegra20)
+- bus-range: Range of bus numbers associated with this controller
+- #address-cells: Address representation for root ports (must be 3)
+  - cell 0 specifies the bus and device numbers of the root port:
+    [23:16]: bus number
+    [15:11]: device number
+  - cell 1 denotes the upper 32 address bits and should be 0
+  - cell 2 contains the lower 32 address bits and is used to translate to the
+    CPU address space
+- #size-cells: Size representation for root ports (must be 2)
+- ranges: Describes the translation of addresses for root ports and standard
+  PCI regions. The entries must be 6 cells each, where the first three cells
+  correspond to the address as described for the #address-cells property
+  above, the fourth cell is the physical CPU address to translate to and the
+  fifth and six cells are as described for the #size-cells property above.
+  - The first two entries are expected to translate the addresses for the root
+    port registers, which are referenced by the assigned-addresses property of
+    the root port nodes (see below).
+  - The remaining entries setup the mapping for the standard I/O, memory and
+    prefetchable PCI regions. The first cell determines the type of region
+    that is setup:
+    - 0x81000000: I/O memory region
+    - 0x82000000: non-prefetchable memory region
+    - 0xc2000000: prefetchable memory region
+  Please refer to the standard PCI bus binding document for a more detailed
+  explanation.
+- clocks: List of clock inputs of the controller. Must contain an entry for
+  each entry in the clock-names property.
+- clock-names: Must include the following entries:
+  "pex": The Tegra clock of that name
+  "afi": The Tegra clock of that name
+  "pcie_xclk": The Tegra clock of that name
+  "pll_e": The Tegra clock of that name
+  "cml": The Tegra clock of that name (not required for Tegra20)
+
+Root ports are defined as subnodes of the PCIe controller node.
+
+Required properties:
+- device_type: Must be "pci"
+- assigned-addresses: Address and size of the port configuration registers
+- reg: PCI bus address of the root port
+- #address-cells: Must be 3
+- #size-cells: Must be 2
+- ranges: Sub-ranges distributed from the PCIe controller node. An empty
+  property is sufficient.
+- nvidia,num-lanes: Number of lanes to use for this port. Valid combinations
+  are:
+  - Root port 0 uses 4 lanes, root port 1 is unused.
+  - Both root ports use 2 lanes.
+
+Example:
+
+SoC DTSI:
+
+	pcie-controller {
+		compatible = "nvidia,tegra20-pcie";
+		device_type = "pci";
+		reg = <0x80003000 0x00000800   /* PADS registers */
+		       0x80003800 0x00000200   /* AFI registers */
+		       0x90000000 0x10000000>; /* configuration space */
+		reg-names = "pads", "afi", "cs";
+		interrupts = <0 98 0x04   /* controller interrupt */
+		              0 99 0x04>; /* MSI interrupt */
+		interrupt-names = "intr", "msi";
+
+		bus-range = <0x00 0xff>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		ranges = <0x82000000 0 0x80000000 0x80000000 0 0x00001000   /* port 0 registers */
+			  0x82000000 0 0x80001000 0x80001000 0 0x00001000   /* port 1 registers */
+			  0x81000000 0 0          0x82000000 0 0x00010000   /* downstream I/O */
+			  0x82000000 0 0xa0000000 0xa0000000 0 0x10000000   /* non-prefetchable memory */
+			  0xc2000000 0 0xb0000000 0xb0000000 0 0x10000000>; /* prefetchable memory */
+
+		clocks = <&tegra_car 70>, <&tegra_car 72>, <&tegra_car 74>,
+			 <&tegra_car 118>;
+		clock-names = "pex", "afi", "pcie_xclk", "pll_e";
+		status = "disabled";
+
+		pci@1,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82000800 0 0x80000000 0 0x1000>;
+			reg = <0x000800 0 0 0 0>;
+			status = "disabled";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges;
+
+			nvidia,num-lanes = <2>;
+		};
+
+		pci@2,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82001000 0 0x80001000 0 0x1000>;
+			reg = <0x001000 0 0 0 0>;
+			status = "disabled";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges;
+
+			nvidia,num-lanes = <2>;
+		};
+	};
+
+
+Board DTS:
+
+	pcie-controller {
+		status = "okay";
+
+		vdd-supply = <&pci_vdd_reg>;
+		pex-clk-supply = <&pci_clk_reg>;
+
+		/* root port 00:01.0 */
+		pci@1,0 {
+			status = "okay";
+
+			/* bridge 01:00.0 (optional) */
+			pci@0,0 {
+				reg = <0x010000 0 0 0 0>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+
+				device_type = "pci";
+
+				/* endpoint 02:00.0 */
+				pci@0,0 {
+					reg = <0x020000 0 0 0 0>;
+				};
+			};
+		};
+	};
+
+Note that devices on the PCI bus are dynamically discovered using PCI's bus
+enumeration and therefore don't need corresponding device nodes in DT. However
+if a device on the PCI bus provides a non-probeable bus such as I2C or SPI,
+device nodes need to be added in order to allow the bus' children to be
+instantiated at the proper location in the operating system's device tree (as
+illustrated by the optional nodes in the example above).