talos-obmc-linux/drivers/net/ethernet/renesas, branch dev-5.0

ravb: Decrease TxFIFO depth of Q3 and Q2 to one

2019-03-19T12:10:54+00:00

[ Upstream commit ae9819e339b451da7a86ab6fe38ecfcb6814e78a ] Hardware has the CBS (Credit Based Shaper) which affects only Q3 and Q2. When updating the CBS settings, even if the driver does so after waiting for Tx DMA finished, there is a possibility that frame data still remains in TxFIFO. To avoid this, decrease TxFIFO depth of Q3 and Q2 to one. This patch has been exercised this using netperf TCP_MAERTS, TCP_STREAM and UDP_STREAM tests run on an Ebisu board. No performance change was detected, outside of noise in the tests, both in terms of throughput and CPU utilisation. Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper") Signed-off-by: Masaru Nagai Signed-off-by: Kazuya Mizuguchi [simon: updated changelog] Signed-off-by: Simon Horman Signed-off-by: David S. Miller Signed-off-by: Greg Kroah-Hartman

ravb: expand rx descriptor data to accommodate hw checksum

2019-01-23T17:21:22+00:00

EtherAVB may provide a checksum of packet data appended to packet data. In order to allow this checksum to be received by the host descriptor data needs to be enlarged by 2 bytes to accommodate the checksum. In the case of MTU-sized packets without a VLAN tag the checksum were already accommodated by virtue of the space reserved for the VLAN tag. However, a packet of MTU-size with a VLAN tag consumed all packet data space provided by a descriptor leaving no space for the trailing checksum. This was not detected by the driver which incorrectly used the last two bytes of packet data as the checksum and truncate the packet by two bytes. This resulted all such packets being dropped. A work around is to disable RX checksum offload # ethtool -K eth0 rx off This patch resolves this problem by increasing the size available for packet data in RX descriptors by two bytes. Tested on R-Car E3 (r8a77990) ES1.0 based Ebisu-4D board v2 * Use sizeof(__sum16) directly rather than adding a driver-local #define for the size of the checksum provided by the hw (2 bytes). Fixes: 4d86d3818627 ("ravb: RX checksum offload") Signed-off-by: Simon Horman Reviewed-by: Sergei Shtylyov Signed-off-by: David S. Miller

ravb: Clean up duplex handling

2018-11-23T19:14:47+00:00

Since only full-duplex operation is supported by the hardware, remove duplex handling code and keep the register setting of ECMR.DM fixed at 1. This updates the driver implementation to follow the data sheet text "This bit should always be set to 1." Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper") Signed-off-by: Magnus Damm Reviewed-by: Sergei Shtylyov Signed-off-by: David S. Miller

ravb: Do not announce HDX as supported

2018-11-23T19:14:47+00:00

According to the data sheet the Ethernet-AVB hardware in R-Car Gen3 and R-Car Gen2 SoCs do not support half duplex operation. So update the driver to mark 100Mbit and 1Gbps HDX as unsupported. Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper") Signed-off-by: Magnus Damm Reviewed-by: Sergei Shtylyov Signed-off-by: David S. Miller

Merge ra.kernel.org:/pub/scm/linux/kernel/git/davem/net

2018-09-25T17:35:29+00:00

Version bump conflict in batman-adv, take what's in net-next. iavf conflict, adjustment of netdev_ops in net-next conflicting with poll controller method removal in net. Signed-off-by: David S. Miller

ravb: Disable Pause Advertisement

2018-09-22T02:26:52+00:00

The previous commit to ravb had the side effect of making the PHY advertise Pause and Asym Pause, which previously did not happen. By default, phydev->supported has both forms of pause enabled, but phydev->advertising does not. The new phy_remove_link_mode() copies phydev->supported to phydev->advertising after removing the requested link mode. These Pause configuration bits appears it stops the PHY from completing Auto-Neg and the link remains down. Be explicit and remove the Pause and Asym Pause modes, so restoring the old behavior. Fixes: 41124fa64d4b ("net: ethernet: Add helper to remove a supported link mode") Reported-by: Simon Horman Signed-off-by: Andrew Lunn Reviewed-by: Sergei Shtylyov Signed-off-by: David S. Miller

ravb: remove tx buffer addr 4byte alilgnment restriction for R-Car Gen3

2018-09-20T04:08:20+00:00

This patch sets from two descriptor to one descriptor because R-Car Gen3 does not have the 4 bytes alignment restriction of the transmission buffer. Signed-off-by: Kazuya Mizuguchi Signed-off-by: Simon Horman Signed-off-by: David S. Miller

ravb: do not write 1 to reserved bits

2018-09-19T03:09:57+00:00

EtherAVB hardware requires 0 to be written to status register bits in order to clear them, however, care must be taken not to: 1. Clear other bits, by writing zero to them 2. Write one to reserved bits This patch corrects the ravb driver with respect to the second point above. This is done by defining reserved bit masks for the affected registers and, after auditing the code, ensure all sites that may write a one to a reserved bit use are suitably masked. Signed-off-by: Kazuya Mizuguchi Signed-off-by: Simon Horman Reviewed-by: Sergei Shtylyov Signed-off-by: David S. Miller

Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net

2018-09-13T05:22:42+00:00

net: ethernet: Add helper to remove a supported link mode

2018-09-13T03:24:21+00:00

Some MAC hardware cannot support a subset of link modes. e.g. often 1Gbps Full duplex is supported, but Half duplex is not. Add a helper to remove such a link mode. Signed-off-by: Andrew Lunn Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller