ASCII_VPD_LX_KEYWORD
LX keyword VPD data for HDAT module
non-volatile
CHIP_VER
Enumeration indicating the chip version
DD10
0x10
DD11
0x11
DD20
0x20
DD21
0x21
DD10
CHIP_VER
Attribute indicating the target's chip version
CHIP_VER
non-volatile
CREATE_DEF_PARTITION
User configuration for creating default partition
volatile-zeroed
ENLARGED_IO_SLOT_COUNT
User configuration for Enlarged IO SLot Count
volatile-zeroed
HUGE_PAGE_COUNT
Huge Memory Page Count
volatile-zeroed
HUGE_PAGE_SIZE
Huge Memory Page Size
volatile-zeroed
HW_VER
Enumeration indicating the chip HW version
FSP_HW_VER
0x2
BMC_HW_VER
0x3
BMC_HW_VER
HW_VER
Attribute indicating the target's hw version
HW_VER
non-volatile
HYPERVISOR_IPL_DESTINATION
Hypervisor IPL Destination
volatile-zeroed
HYPERVISOR_IPL_SIDE
Platform IPL Side
volatile-zeroed
HYP_DISPATCH_WHEEL
Hypervisor Dispatch Wheel
volatile-zeroed
IPL_ATTRIBUTES
Assorted list of differnt IPL attributes passed via HDAT
struct - 8 booleans
createDefaultPartition
0b0: Dont create default partition;
0b1: Create default partition;
uint8_t
1
0
clickToAcceptState
0b0: Customer has not accepted license agreement;
0b1: Customer has accepted license agreement;
uint8_t
1
0
disableVirtIO
0b0: Enable Virtual IO Connections between partitions;
0b1: Disable Virtual IO Connections between partitions;
uint8_t
1
0
resetPCINumbers
0b0: Do not reset PCI Numbers;
0b1: Reset PCI Numbers;
uint8_t
1
0
clearHypNVRAM
0b0: Do not clear HYP NVRAM;
0b1: Clear HYP NVRAM;
uint8_t
1
0
deleteHYPSELs
0b0: Do not delete SELs originating from HYP;
0b1: Delete SELs originating from HYP;
uint8_t
1
0
deleteHBSELs
0b0: Do not delete SELs originating from Hostboot;
0b1: Delete SELs originating from Hostboot;
uint8_t
1
0
deleteBMCSELs
0b0: Do not delete SELs originating from BMC;
0b1: Delete SELs originating from BMC;
uint8_t
1
0
volatile-zeroed
IPS_ENABLE
Indicates if Idle Power Save is enabled. This is independent of
the OPEN_POWER_PM_MODE (DPS and IPS can be enabled at the same time).
Valid Values: 0 = Disabled (default), 1 = Enabled.
See IPS_ENTER / IPS_EXIT attributes for IPS configuration.
0
non-volatile
IPS_ENTER_TIME_SECONDS
When IPS is enabled, this defines the delay time in seconds
(between 10 and 600) to enter Idle Power Save.
240
non-volatile
IPS_ENTER_UTILIZATION_PERCENT
When IPS is enabled, this defines the utilization threshold as a
percent (between 0 and 100) to enter Idle Power Save. This value
should be less than IPS_EXIT_UTILIZATION_PERCENT.
8
non-volatile
IPS_EXIT_TIME_SECONDS
When IPS is enabled, this defines the delay time in seconds
(between 10 and 600) to exit Idle Power Save.
10
non-volatile
IPS_EXIT_UTILIZATION_PERCENT
When IPS is enabled, this defines the utilization threshold as a
percent (between 0 and 100) to exit Idle Power Save. This value
should be greater than IPS_ENTER_UTILIZATION_PERCENT.
12
non-volatile
LMB_SIZE
Logical Memory Block Size
volatile-zeroed
MAX_HSL_OPTICONNECT_CONNECTIONS
User configuration for max HSL Opticonnect connections
volatile-zeroed
OPEN_POWER_PM_MODE
Power management mode the system should use.
Valid values: 1 = Nominal (default),
5 = Static Power Save (percentage below nominal whose value
is defined in OPEN_POWER_PM_MODE_FREQ_PERCENT),
6 = Dynamic Power Save - Favor Energy (DPS-FE),
10 = Dynamic Power Save - Favor Performance (DPS-FP),
11 = Fixed Frequency Override - (percentage above nominal whose
value is defined in OPEN_POWER_PM_MODE_FREQ_PERCENT)
1
non-volatile
OPEN_POWER_PM_MODE_FREQ_PERCENT
Percentage from nominal that the processors should run at when
OPEN_POWER_PM_MODE is set to Static Power Save or
Fixed Frequency Override (ignored on all other modes).
Unit is in tenths of a percent (150 = 15.0%).
Static Power Save (5): percentage to decrease frequency,
Fixed Frequency Override (11): percentage to increase frequency
non-volatile
OS_IPL_MODE
Operating System IPL Mode
volatile-zeroed
PHYP_SYSTEM_TYPE
PHYP system type value for habanero
and barreleye (0x3015 and 0x3016 respectively).
The value is updated in the system xml.
non-volatile
PRESERVE_MDC_PARTITION_VPD
MFG setting to preserve MDC partition vpd
volatile-zeroed
PROC_HW_TOPOLOGY
Hardware topology for HDAT
creator:MRW
consumer:HDAT
firmware notes:
Hardware Topology 2 Bytes
Byte 1:
bit 0-3: Node Id
bit 4-7: Socket id inside the node
bit 8-11: Proc id inside socket
bit 12-15:Hub Id inside proc
non-volatile
ROLE
Enumeration indicating the master's FSI type
PRIMARY
1
BACKUP
0
PRIMARY
ROLE
Attribute indicating the target's role
ROLE
non-volatile
SLCA_INDEX
SLCA index for this FRU
volatile-zeroed
SLCA_RID
SLCA RID for this FRU
volatile-zeroed
SW_VER
Enumeration indicating the SW version
FSP_SW_VER
0x1
BMC_SW_VER
0x2
BMC_SW_VER
SW_VER
Attribute indicating the target's software version
SW_VER
non-volatile
SYSTEM_BRAND_NAME
Brand Name of OEM systems
64
non-volatile
VLAN_SWITCHES
Number of VLAN Switches
volatile-zeroed
VTPM_ENABLED
Virtual TPM Enabled
volatile-zeroed