buildroot/configs, branch 2016.05

configs: zynq: revive BR2_LINUX_KERNEL_UIMAGE

2016-05-28T13:50:31+00:00

Commit 5c67cb1d0445 ("linux: use zImage by default on ARM") changed the default kernel image, but missed to update Zynq defconfigs. U-Boot on Zynq boards still loads uImage, so BR2_LINUX_KERNEL_UIMAGE should be defined to generate uImage. Signed-off-by: Masahiro Yamada Signed-off-by: Thomas Petazzoni

m68k: fix open issues with qemu coldfire

2016-05-11T13:27:15+00:00

Enable kernel drivers for networking and add a simple busybox config with basic network tools. Add kernel patch from Linux git to fix hush segfaults while using signal handler. Signed-off-by: Waldemar Brodkorb Signed-off-by: Thomas Petazzoni

configs: warpboard: Use the final U-boot release version

2016-05-09T12:03:12+00:00

We should better use the final U-boot version rather than the release candidate one. Signed-off-by: Fabio Estevam Signed-off-by: Peter Korsgaard

boards/raspberrypi0: new board

2016-05-08T13:54:30+00:00

Add support for the rpi-0, which is basically a rpi (model A+) in a smaller form-factor. This one does not have an ethernet port, so we just remove it from the configuration (or we could use the existing rasbperrypi_defconfig and suffer from a longer boot time because of the waiting for eth0). Signed-off-by: "Yann E. MORIN" Signed-off-by: Thomas Petazzoni

configs/imx6ulevk: Use ext4 as filesystem type

2016-05-08T13:01:52+00:00

Extend the filesystem type to ext4. Signed-off-by: Fabio Estevam Signed-off-by: Thomas Petazzoni

configs/freescale_mpc8315erdb: bump to kernel 4.5.3

2016-05-05T20:19:11+00:00

Signed-off-by: Gustavo Zacarias Signed-off-by: Thomas Petazzoni

configs/freescale_p1010rdb_pa: lock down binutils version

2016-05-05T20:18:56+00:00

The used U-Boot version (2014.01) isn't too happy with newer (>= 2.25) binutils versions, so keep it locked down until the config is updated for a newer version. Signed-off-by: Gustavo Zacarias Signed-off-by: Thomas Petazzoni

configs/freescale_mpc8315erdb: lock down binutils version

2016-05-05T20:18:53+00:00

The used U-Boot version (2014.04) isn't too happy with newer (>= 2.25) binutils versions, so keep it locked down until the config is updated for a newer version. U-Boot 2016.03 in fact does work for mpc8315erdb - however it doesn't yet support SPL which is necessary for NAND boot and would be a massive defconfig revamp switching to NOR. Signed-off-by: Gustavo Zacarias Signed-off-by: Thomas Petazzoni

configs/qemu: bump to the latest version

2016-05-05T13:41:32+00:00

Results table: Defconfig Kernel Qemu Network Status ------------------------------------------------------------------ aarch64_virt 4.5.3 2.5.0 YES OK arm_versatile 4.5.3 2.5.0 YES OK arm_vexpress 4.5.3 2.5.0 YES OK m68k_mcf5208 4.5.3 2.5.0 NO SO-SO (3) m68k_q800 4.5.3 q800-v2.4.0 NO (4) OK microblazebe 4.5.3 2.5.0 YES OK microblazeel 4.5.3 2.5.0 YES OK mips64el_malta 4.5.3 2.5.0 YES OK mips64_malta 4.5.3 2.5.0 YES OK mipsel_malta 4.5.3 2.5.0 YES OK mips_malta 4.5.3 2.5.0 YES OK ppc_g3beige 4.5.3 2.5.0 YES OK ppc_mpc8544ds 4.5.3 2.5.0 YES OK ppc_virtex_ml507 4.5.3 2.5.0 NO OK ppc64_pseries 4.5.3 2.5.0 YES OK sh4 4.5.3 2.5.0 YES OK sh4eb 4.5.3 2.5.0 NO (1) OK sparc_ss10 4.5.3 2.5.0 YES OK sparc64_sun4u 4.5.3 2.5.0 YES OK sparc_sun4u 4.5.3 2.5.0 YES OK x86 4.5.3 2.5.0 YES OK x86_64 4.5.3 2.5.0 YES OK xtensa_lx60 4.4.9 2.5.0 YES (2) OK xtensa_lx60_nommu 4.4.9 2.5.0 YES (2) OK (1) - Probably an endian issue with 8139 emulation/driver (2) - xtensa ethernet broken in 4.5 (3) - It boots, you can login, but apps exit/crash often (4) - There's a network interface, but enabling it in qemu fails Signed-off-by: Gustavo Zacarias Signed-off-by: Thomas Petazzoni

configs/qemu: use zImage for sh4/sh4eb samples

2016-05-05T13:39:51+00:00

The default for ARM was changed to zImage in 5c67cb1d, however the sh4/sh4eb sample configs were updated to switch to uImage in error, hence end up building uImage which doesn't work with Qemu. Signed-off-by: Gustavo Zacarias [Thomas: fix commit log.] Signed-off-by: Thomas Petazzoni