buildroot/board/raspberrypi, branch 2017.05

configs: add raspberrypi3 64bits defconfig

2017-05-04T07:25:20+00:00

This configuration builds a 64bit image for RaspberryPi 3. The size of the ext4 filesystem has to be extended to fit the large amount (~60MB) of kernel modules enabled in the defconfig. [Peter: drop gcc version selection / glibc, explain ext4 size requirement] Signed-off-by: Gaël PORTAY Tested-by: Ricardo Martincoski Signed-off-by: Peter Korsgaard

configs/raspberrypi3_defconfig: add raspberry pi 3 compute module support

2017-03-05T20:25:51+00:00

Signed-off-by: Martin Bark Signed-off-by: Thomas Petazzoni

configs/raspberrypi0_defconfig: add raspberry pi zero w support

2017-03-05T20:25:51+00:00

Signed-off-by: Martin Bark Signed-off-by: Thomas Petazzoni

board: raspberrypi: mention the Zero model in readme.txt

2017-01-26T21:43:34+00:00

Cc: "Yann E. MORIN" Cc: Peter Seiderer Signed-off-by: Baruch Siach Acked-by: "Yann E. MORIN" Signed-off-by: Peter Korsgaard

board: raspberrypi: don't generate a marked kernel

2017-01-26T21:35:15+00:00

We no longer use the marked kernel. Cc: Peter Seiderer Signed-off-by: Baruch Siach Reviewed-by: "Yann E. MORIN" Signed-off-by: Peter Korsgaard

board: raspberrypi: use regular kernel image

2017-01-26T21:35:05+00:00

Since release 4.4 a kernel without a trailer is assumed to be device tree capable. Since our Raspberry Pi defconfigs all use the newer firmware we can just use the regular kernel image. https://www.raspberrypi.org/documentation/configuration/device-tree.md Tested on Raspberry Pi 3. Cc: Peter Seiderer Signed-off-by: Baruch Siach Reviewed-by: "Yann E. MORIN" Signed-off-by: Peter Korsgaard

raspberrypi3: fix serial console (load pi3-miniuart-bt overlay)

2016-09-18T17:21:18+00:00

- enable BR2_PACKAGE_RPI_FIRMWARE_INSTALL_DTB_OVERLAYS in raspberrypi3_defconfig - add copy of rpi-firmware/overlays directory to boot partition in genimage-raspberrypi3.cfg - enhance post-image.sh script to add 'dtoverlay=pi3-miniuart-bt' on request - add BR2_ROOTFS_POST_SCRIPT_ARGS="--add-pi3-miniuart-bt-overlay" in raspberrypi3_defconfig Signed-off-by: Peter Seiderer Signed-off-by: Thomas Petazzoni

board/raspberrypi/post-build.sh: only tweak /etc/inittab if available

2016-08-26T13:37:17+00:00

As pointed out in bug #9161, we don't always have an inittab file (if systemd or no init is used), so the post build script should only try to tweak it if present. Signed-off-by: Peter Korsgaard Signed-off-by: Thomas Petazzoni

boards/raspberrypi0: new board

2016-05-08T13:54:30+00:00

Add support for the rpi-0, which is basically a rpi (model A+) in a smaller form-factor. This one does not have an ethernet port, so we just remove it from the configuration (or we could use the existing rasbperrypi_defconfig and suffer from a longer boot time because of the waiting for eth0). Signed-off-by: "Yann E. MORIN" Signed-off-by: Thomas Petazzoni

configs: add Raspberry Pi 3 defconfig

2016-04-25T12:07:58+00:00

So far identical to the rpi2 one except for the dts file as the SW runs in 32bit mode. [Peter: extend commit message] Signed-off-by: Ubaldo Porcheddu Signed-off-by: Peter Korsgaard