1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
|
/*
* Power management for audio on multifunction CS5535 companion device
* Copyright (C) Jaya Kumar
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*
*/
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/pci.h>
#include <linux/delay.h>
#include <sound/driver.h>
#include <sound/core.h>
#include <sound/control.h>
#include <sound/initval.h>
#include <sound/asoundef.h>
#include <sound/pcm.h>
#include <sound/ac97_codec.h>
#include "cs5535audio.h"
static void snd_cs5535audio_stop_hardware(struct cs5535audio *cs5535au)
{
/*
we depend on snd_ac97_suspend to tell the
AC97 codec to shutdown. the amd spec suggests
that the LNK_SHUTDOWN be done at the same time
that the codec power-down is issued. instead,
we do it just after rather than at the same
time. excluding codec specific build_ops->suspend
ac97 powerdown hits:
0x8000 EAPD
0x4000 Headphone amplifier
0x0300 ADC & DAC
0x0400 Analog Mixer powerdown (Vref on)
I am not sure if this is the best that we can do.
The remainder to be investigated are:
- analog mixer (vref off) 0x0800
- AC-link powerdown 0x1000
- codec internal clock 0x2000
*/
/* set LNK_SHUTDOWN to shutdown AC link */
cs_writel(cs5535au, ACC_CODEC_CNTL, ACC_CODEC_CNTL_LNK_SHUTDOWN);
}
int snd_cs5535audio_suspend(struct pci_dev *pci, pm_message_t state)
{
struct snd_card *card = pci_get_drvdata(pci);
struct cs5535audio *cs5535au = card->private_data;
int i;
snd_power_change_state(card, SNDRV_CTL_POWER_D3hot);
for (i = 0; i < NUM_CS5535AUDIO_DMAS; i++) {
struct cs5535audio_dma *dma = &cs5535au->dmas[i];
if (dma && dma->substream && !dma->suspended)
dma->saved_prd = dma->ops->read_prd(cs5535au);
}
snd_pcm_suspend_all(cs5535au->pcm);
snd_ac97_suspend(cs5535au->ac97);
/* save important regs, then disable aclink in hw */
snd_cs5535audio_stop_hardware(cs5535au);
pci_disable_device(pci);
pci_save_state(pci);
pci_set_power_state(pci, pci_choose_state(pci, state));
return 0;
}
int snd_cs5535audio_resume(struct pci_dev *pci)
{
struct snd_card *card = pci_get_drvdata(pci);
struct cs5535audio *cs5535au = card->private_data;
u32 tmp;
int timeout;
int i;
pci_set_power_state(pci, PCI_D0);
pci_restore_state(pci);
if (pci_enable_device(pci) < 0) {
printk(KERN_ERR "cs5535audio: pci_enable_device failed, "
"disabling device\n");
snd_card_disconnect(card);
return -EIO;
}
pci_set_master(pci);
/* set LNK_WRM_RST to reset AC link */
cs_writel(cs5535au, ACC_CODEC_CNTL, ACC_CODEC_CNTL_LNK_WRM_RST);
timeout = 50;
do {
tmp = cs_readl(cs5535au, ACC_CODEC_STATUS);
if (tmp & PRM_RDY_STS)
break;
udelay(1);
} while (--timeout);
if (!timeout)
snd_printk(KERN_ERR "Failure getting AC Link ready\n");
/* we depend on ac97 to perform the codec power up */
snd_ac97_resume(cs5535au->ac97);
/* set up rate regs, dma. actual initiation is done in trig */
for (i = 0; i < NUM_CS5535AUDIO_DMAS; i++) {
struct cs5535audio_dma *dma = &cs5535au->dmas[i];
if (dma && dma->substream && dma->suspended) {
dma->substream->ops->prepare(dma->substream);
dma->ops->setup_prd(cs5535au, dma->saved_prd);
}
}
snd_power_change_state(card, SNDRV_CTL_POWER_D0);
return 0;
}
|
