blob: 67bbcf0785f61da1d4a832e016de1cb99dd313a9 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
|
/*
* MMC definitions for OMAP2
*
* Copyright (C) 2006 Nokia Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
/*
* struct omap_hsmmc_dev_attr.flags possibilities
*
* OMAP_HSMMC_SUPPORTS_DUAL_VOLT: Some HSMMC controller instances can
* operate with either 1.8Vdc or 3.0Vdc card voltages; this flag
* should be set if this is the case. See for example Section 22.5.3
* "MMC/SD/SDIO1 Bus Voltage Selection" of the OMAP34xx Multimedia
* Device Silicon Revision 3.1.x Revision ZR (July 2011) (SWPU223R).
*
* OMAP_HSMMC_BROKEN_MULTIBLOCK_READ: Multiple-block read transfers
* don't work correctly on some MMC controller instances on some
* OMAP3 SoCs; this flag should be set if this is the case. See
* for example Advisory 2.1.1.128 "MMC: Multiple Block Read
* Operation Issue" in _OMAP3530/3525/3515/3503 Silicon Errata_
* Revision F (October 2010) (SPRZ278F).
*/
#define OMAP_HSMMC_SUPPORTS_DUAL_VOLT BIT(0)
#define OMAP_HSMMC_BROKEN_MULTIBLOCK_READ BIT(1)
#define OMAP_HSMMC_SWAKEUP_MISSING BIT(2)
struct omap_hsmmc_dev_attr {
u8 flags;
};
struct mmc_card;
struct omap_hsmmc_platform_data {
/* back-link to device */
struct device *dev;
/* set if your board has components or wiring that limits the
* maximum frequency on the MMC bus */
unsigned int max_freq;
/* Integrating attributes from the omap_hwmod layer */
u8 controller_flags;
/* Register offset deviation */
u16 reg_offset;
/*
* 4/8 wires and any additional host capabilities
* need to OR'd all capabilities (ref. linux/mmc/host.h)
*/
u32 caps; /* Used for the MMC driver on 2430 and later */
u32 pm_caps; /* PM capabilities of the mmc */
/* switch pin can be for card detect (default) or card cover */
unsigned cover:1;
/* use the internal clock */
unsigned internal_clock:1;
/* nonremovable e.g. eMMC */
unsigned nonremovable:1;
/* eMMC does not handle power off when not in sleep state */
unsigned no_regulator_off_init:1;
/* we can put the features above into this variable */
#define HSMMC_HAS_PBIAS (1 << 0)
#define HSMMC_HAS_UPDATED_RESET (1 << 1)
#define HSMMC_HAS_HSPE_SUPPORT (1 << 2)
unsigned features;
int switch_pin; /* gpio (card detect) */
int gpio_wp; /* gpio (write protect) */
int (*set_power)(struct device *dev, int power_on, int vdd);
void (*remux)(struct device *dev, int power_on);
/* Call back before enabling / disabling regulators */
void (*before_set_reg)(struct device *dev, int power_on, int vdd);
/* Call back after enabling / disabling regulators */
void (*after_set_reg)(struct device *dev, int power_on, int vdd);
/* if we have special card, init it using this callback */
void (*init_card)(struct mmc_card *card);
const char *name;
u32 ocr_mask;
};
|
