blob: 457c75a4622f01b1e351cc5b5dce959df2291b45 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
|
/*
* keylargo.h: definitions for using the "KeyLargo" I/O controller chip.
*
*/
/* "Pangea" chipset has keylargo device-id 0x25 while core99
* has device-id 0x22. The rev. of the pangea one is 0, so we
* fake an artificial rev. in keylargo_rev by oring 0x100
*/
#define KL_PANGEA_REV 0x100
/* offset from base for feature control registers */
#define KEYLARGO_MBCR 0x34 /* KL Only, Media bay control/status */
#define KEYLARGO_FCR0 0x38
#define KEYLARGO_FCR1 0x3c
#define KEYLARGO_FCR2 0x40
#define KEYLARGO_FCR3 0x44
#define KEYLARGO_FCR4 0x48
#define KEYLARGO_FCR5 0x4c /* Pangea only */
/* K2 aditional FCRs */
#define K2_FCR6 0x34
#define K2_FCR7 0x30
#define K2_FCR8 0x2c
#define K2_FCR9 0x28
#define K2_FCR10 0x24
/* GPIO registers */
#define KEYLARGO_GPIO_LEVELS0 0x50
#define KEYLARGO_GPIO_LEVELS1 0x54
#define KEYLARGO_GPIO_EXTINT_0 0x58
#define KEYLARGO_GPIO_EXTINT_CNT 18
#define KEYLARGO_GPIO_0 0x6A
#define KEYLARGO_GPIO_CNT 17
#define KEYLARGO_GPIO_EXTINT_DUAL_EDGE 0x80
#define KEYLARGO_GPIO_OUTPUT_ENABLE 0x04
#define KEYLARGO_GPIO_OUTOUT_DATA 0x01
#define KEYLARGO_GPIO_INPUT_DATA 0x02
/* K2 does only extint GPIOs and does 51 of them */
#define K2_GPIO_EXTINT_0 0x58
#define K2_GPIO_EXTINT_CNT 51
/* Specific GPIO regs */
#define KL_GPIO_MODEM_RESET (KEYLARGO_GPIO_0+0x03)
#define KL_GPIO_MODEM_POWER (KEYLARGO_GPIO_0+0x02) /* Pangea */
#define KL_GPIO_SOUND_POWER (KEYLARGO_GPIO_0+0x05)
/* Hrm... this one is only to be used on Pismo. It seeem to also
* control the timebase enable on other machines. Still to be
* experimented... --BenH.
*/
#define KL_GPIO_FW_CABLE_POWER (KEYLARGO_GPIO_0+0x09)
#define KL_GPIO_TB_ENABLE (KEYLARGO_GPIO_0+0x09)
#define KL_GPIO_ETH_PHY_RESET (KEYLARGO_GPIO_0+0x10)
#define KL_GPIO_EXTINT_CPU1 (KEYLARGO_GPIO_0+0x0a)
#define KL_GPIO_EXTINT_CPU1_ASSERT 0x04
#define KL_GPIO_EXTINT_CPU1_RELEASE 0x38
#define KL_GPIO_RESET_CPU0 (KEYLARGO_GPIO_EXTINT_0+0x03)
#define KL_GPIO_RESET_CPU1 (KEYLARGO_GPIO_EXTINT_0+0x04)
#define KL_GPIO_RESET_CPU2 (KEYLARGO_GPIO_EXTINT_0+0x0f)
#define KL_GPIO_RESET_CPU3 (KEYLARGO_GPIO_EXTINT_0+0x10)
#define KL_GPIO_PMU_MESSAGE_IRQ (KEYLARGO_GPIO_EXTINT_0+0x09)
#define KL_GPIO_PMU_MESSAGE_BIT KEYLARGO_GPIO_INPUT_DATA
#define KL_GPIO_MEDIABAY_IRQ (KEYLARGO_GPIO_EXTINT_0+0x0e)
#define KL_GPIO_AIRPORT_0 (KEYLARGO_GPIO_EXTINT_0+0x0a)
#define KL_GPIO_AIRPORT_1 (KEYLARGO_GPIO_EXTINT_0+0x0d)
#define KL_GPIO_AIRPORT_2 (KEYLARGO_GPIO_0+0x0d)
#define KL_GPIO_AIRPORT_3 (KEYLARGO_GPIO_0+0x0e)
#define KL_GPIO_AIRPORT_4 (KEYLARGO_GPIO_0+0x0f)
/*
* Bits in feature control register. Those bits different for K2 are
* listed separately
*/
#define KL_MBCR_MB0_PCI_ENABLE 0x00000800 /* exist ? */
#define KL_MBCR_MB0_IDE_ENABLE 0x00001000
#define KL_MBCR_MB0_FLOPPY_ENABLE 0x00002000 /* exist ? */
#define KL_MBCR_MB0_SOUND_ENABLE 0x00004000 /* hrm... */
#define KL_MBCR_MB0_DEV_MASK 0x00007800
#define KL_MBCR_MB0_DEV_POWER 0x00000400
#define KL_MBCR_MB0_DEV_RESET 0x00000200
#define KL_MBCR_MB0_ENABLE 0x00000100
#define KL_MBCR_MB1_PCI_ENABLE 0x08000000 /* exist ? */
#define KL_MBCR_MB1_IDE_ENABLE 0x10000000
#define KL_MBCR_MB1_FLOPPY_ENABLE 0x20000000 /* exist ? */
#define KL_MBCR_MB1_SOUND_ENABLE 0x40000000 /* hrm... */
#define KL_MBCR_MB1_DEV_MASK 0x78000000
#define KL_MBCR_MB1_DEV_POWER 0x04000000
#define KL_MBCR_MB1_DEV_RESET 0x02000000
#define KL_MBCR_MB1_ENABLE 0x01000000
#define KL0_SCC_B_INTF_ENABLE 0x00000001 /* (KL Only) */
#define KL0_SCC_A_INTF_ENABLE 0x00000002
#define KL0_SCC_SLOWPCLK 0x00000004
#define KL0_SCC_RESET 0x00000008
#define KL0_SCCA_ENABLE 0x00000010
#define KL0_SCCB_ENABLE 0x00000020
#define KL0_SCC_CELL_ENABLE 0x00000040
#define KL0_IRDA_HIGH_BAND 0x00000100 /* (KL Only) */
#define KL0_IRDA_SOURCE2_SEL 0x00000200 /* (KL Only) */
#define KL0_IRDA_SOURCE1_SEL 0x00000400 /* (KL Only) */
#define KL0_PG_USB0_PMI_ENABLE 0x00000400 /* (Pangea/Intrepid Only) */
#define KL0_IRDA_RESET 0x00000800 /* (KL Only) */
#define KL0_PG_USB0_REF_SUSPEND_SEL 0x00000800 /* (Pangea/Intrepid Only) */
#define KL0_IRDA_DEFAULT1 0x00001000 /* (KL Only) */
#define KL0_PG_USB0_REF_SUSPEND 0x00001000 /* (Pangea/Intrepid Only) */
#define KL0_IRDA_DEFAULT0 0x00002000 /* (KL Only) */
#define KL0_PG_USB0_PAD_SUSPEND 0x00002000 /* (Pangea/Intrepid Only) */
#define KL0_IRDA_FAST_CONNECT 0x00004000 /* (KL Only) */
#define KL0_PG_USB1_PMI_ENABLE 0x00004000 /* (Pangea/Intrepid Only) */
#define KL0_IRDA_ENABLE 0x00008000 /* (KL Only) */
#define KL0_PG_USB1_REF_SUSPEND_SEL 0x00008000 /* (Pangea/Intrepid Only) */
#define KL0_IRDA_CLK32_ENABLE 0x00010000 /* (KL Only) */
#define KL0_PG_USB1_REF_SUSPEND 0x00010000 /* (Pangea/Intrepid Only) */
#define KL0_IRDA_CLK19_ENABLE 0x00020000 /* (KL Only) */
#define KL0_PG_USB1_PAD_SUSPEND 0x00020000 /* (Pangea/Intrepid Only) */
#define KL0_USB0_PAD_SUSPEND0 0x00040000
#define KL0_USB0_PAD_SUSPEND1 0x00080000
#define KL0_USB0_CELL_ENABLE 0x00100000
#define KL0_USB1_PAD_SUSPEND0 0x00400000
#define KL0_USB1_PAD_SUSPEND1 0x00800000
#define KL0_USB1_CELL_ENABLE 0x01000000
#define KL0_USB_REF_SUSPEND 0x10000000 /* (KL Only) */
#define KL0_SERIAL_ENABLE (KL0_SCC_B_INTF_ENABLE | \
KL0_SCC_SLOWPCLK | \
KL0_SCC_CELL_ENABLE | KL0_SCCA_ENABLE)
#define KL1_USB2_PMI_ENABLE 0x00000001 /* Intrepid only */
#define KL1_AUDIO_SEL_22MCLK 0x00000002 /* KL/Pangea only */
#define KL1_USB2_REF_SUSPEND_SEL 0x00000002 /* Intrepid only */
#define KL1_USB2_REF_SUSPEND 0x00000004 /* Intrepid only */
#define KL1_AUDIO_CLK_ENABLE_BIT 0x00000008 /* KL/Pangea only */
#define KL1_USB2_PAD_SUSPEND_SEL 0x00000008 /* Intrepid only */
#define KL1_USB2_PAD_SUSPEND0 0x00000010 /* Intrepid only */
#define KL1_AUDIO_CLK_OUT_ENABLE 0x00000020 /* KL/Pangea only */
#define KL1_USB2_PAD_SUSPEND1 0x00000020 /* Intrepid only */
#define KL1_AUDIO_CELL_ENABLE 0x00000040 /* KL/Pangea only */
#define KL1_USB2_CELL_ENABLE 0x00000040 /* Intrepid only */
#define KL1_AUDIO_CHOOSE 0x00000080 /* KL/Pangea only */
#define KL1_I2S0_CHOOSE 0x00000200 /* KL Only */
#define KL1_I2S0_CELL_ENABLE 0x00000400
#define KL1_I2S0_CLK_ENABLE_BIT 0x00001000
#define KL1_I2S0_ENABLE 0x00002000
#define KL1_I2S1_CELL_ENABLE 0x00020000
#define KL1_I2S1_CLK_ENABLE_BIT 0x00080000
#define KL1_I2S1_ENABLE 0x00100000
#define KL1_EIDE0_ENABLE 0x00800000 /* KL/Intrepid Only */
#define KL1_EIDE0_RESET_N 0x01000000 /* KL/Intrepid Only */
#define KL1_EIDE1_ENABLE 0x04000000 /* KL Only */
#define KL1_EIDE1_RESET_N 0x08000000 /* KL Only */
#define KL1_UIDE_ENABLE 0x20000000 /* KL/Pangea Only */
#define KL1_UIDE_RESET_N 0x40000000 /* KL/Pangea Only */
#define KL2_IOBUS_ENABLE 0x00000002
#define KL2_SLEEP_STATE_BIT 0x00000100 /* KL Only */
#define KL2_PG_STOP_ALL_CLOCKS 0x00000100 /* Pangea Only */
#define KL2_MPIC_ENABLE 0x00020000
#define KL2_CARDSLOT_RESET 0x00040000 /* Pangea/Intrepid Only */
#define KL2_ALT_DATA_OUT 0x02000000 /* KL Only ??? */
#define KL2_MEM_IS_BIG 0x04000000
#define KL2_CARDSEL_16 0x08000000
#define KL3_SHUTDOWN_PLL_TOTAL 0x00000001 /* KL/Pangea only */
#define KL3_SHUTDOWN_PLLKW6 0x00000002 /* KL/Pangea only */
#define KL3_IT_SHUTDOWN_PLL3 0x00000002 /* Intrepid only */
#define KL3_SHUTDOWN_PLLKW4 0x00000004 /* KL/Pangea only */
#define KL3_IT_SHUTDOWN_PLL2 0x00000004 /* Intrepid only */
#define KL3_SHUTDOWN_PLLKW35 0x00000008 /* KL/Pangea only */
#define KL3_IT_SHUTDOWN_PLL1 0x00000008 /* Intrepid only */
#define KL3_SHUTDOWN_PLLKW12 0x00000010 /* KL Only */
#define KL3_IT_ENABLE_PLL3_SHUTDOWN 0x00000010 /* Intrepid only */
#define KL3_PLL_RESET 0x00000020 /* KL/Pangea only */
#define KL3_IT_ENABLE_PLL2_SHUTDOWN 0x00000020 /* Intrepid only */
#define KL3_IT_ENABLE_PLL1_SHUTDOWN 0x00000010 /* Intrepid only */
#define KL3_SHUTDOWN_PLL2X 0x00000080 /* KL Only */
#define KL3_CLK66_ENABLE 0x00000100 /* KL Only */
#define KL3_CLK49_ENABLE 0x00000200
#define KL3_CLK45_ENABLE 0x00000400
#define KL3_CLK31_ENABLE 0x00000800 /* KL/Pangea only */
#define KL3_TIMER_CLK18_ENABLE 0x00001000
#define KL3_I2S1_CLK18_ENABLE 0x00002000
#define KL3_I2S0_CLK18_ENABLE 0x00004000
#define KL3_VIA_CLK16_ENABLE 0x00008000 /* KL/Pangea only */
#define KL3_IT_VIA_CLK32_ENABLE 0x00008000 /* Intrepid only */
#define KL3_STOPPING33_ENABLED 0x00080000 /* KL Only */
#define KL3_PG_PLL_ENABLE_TEST 0x00080000 /* Pangea Only */
/* Intrepid USB bus 2, port 0,1 */
#define KL3_IT_PORT_WAKEUP_ENABLE(p) (0x00080000 << ((p)<<3))
#define KL3_IT_PORT_RESUME_WAKE_EN(p) (0x00040000 << ((p)<<3))
#define KL3_IT_PORT_CONNECT_WAKE_EN(p) (0x00020000 << ((p)<<3))
#define KL3_IT_PORT_DISCONNECT_WAKE_EN(p) (0x00010000 << ((p)<<3))
#define KL3_IT_PORT_RESUME_STAT(p) (0x00300000 << ((p)<<3))
#define KL3_IT_PORT_CONNECT_STAT(p) (0x00200000 << ((p)<<3))
#define KL3_IT_PORT_DISCONNECT_STAT(p) (0x00100000 << ((p)<<3))
/* Port 0,1 : bus 0, port 2,3 : bus 1 */
#define KL4_PORT_WAKEUP_ENABLE(p) (0x00000008 << ((p)<<3))
#define KL4_PORT_RESUME_WAKE_EN(p) (0x00000004 << ((p)<<3))
#define KL4_PORT_CONNECT_WAKE_EN(p) (0x00000002 << ((p)<<3))
#define KL4_PORT_DISCONNECT_WAKE_EN(p) (0x00000001 << ((p)<<3))
#define KL4_PORT_RESUME_STAT(p) (0x00000040 << ((p)<<3))
#define KL4_PORT_CONNECT_STAT(p) (0x00000020 << ((p)<<3))
#define KL4_PORT_DISCONNECT_STAT(p) (0x00000010 << ((p)<<3))
/* Pangea and Intrepid only */
#define KL5_VIA_USE_CLK31 0000000001 /* Pangea Only */
#define KL5_SCC_USE_CLK31 0x00000002 /* Pangea Only */
#define KL5_PWM_CLK32_EN 0x00000004
#define KL5_CLK3_68_EN 0x00000010
#define KL5_CLK32_EN 0x00000020
/* K2 definitions */
#define K2_FCR0_USB0_SWRESET 0x00200000
#define K2_FCR0_USB1_SWRESET 0x02000000
#define K2_FCR0_RING_PME_DISABLE 0x08000000
#define K2_FCR1_PCI1_BUS_RESET_N 0x00000010
#define K2_FCR1_PCI1_SLEEP_RESET_EN 0x00000020
#define K2_FCR1_PCI1_CLK_ENABLE 0x00004000
#define K2_FCR1_FW_CLK_ENABLE 0x00008000
#define K2_FCR1_FW_RESET_N 0x00010000
#define K2_FCR1_GMAC_CLK_ENABLE 0x00400000
#define K2_FCR1_GMAC_POWER_DOWN 0x00800000
#define K2_FCR1_GMAC_RESET_N 0x01000000
#define K2_FCR1_SATA_CLK_ENABLE 0x02000000
#define K2_FCR1_SATA_POWER_DOWN 0x04000000
#define K2_FCR1_SATA_RESET_N 0x08000000
#define K2_FCR1_UATA_CLK_ENABLE 0x10000000
#define K2_FCR1_UATA_RESET_N 0x40000000
#define K2_FCR1_UATA_CHOOSE_CLK66 0x80000000
|
