1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
|
* Samsung S5M8767 Voltage and Current Regulator
The Samsung S5M8767 is a multi-function device which includes voltage and
current regulators, rtc, charger controller and other sub-blocks. It is
interfaced to the host controller using a i2c interface. Each sub-block is
addressed by the host system using different i2c slave address. This document
describes the bindings for 'pmic' sub-block of s5m8767.
Required properties:
- compatible: Should be "samsung,s5m8767-pmic".
- reg: Specifies the i2c slave address of the pmic block. It should be 0x66.
- s5m8767,pmic-buck2-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
units for buck2 when changing voltage using gpio dvs. Refer to [1] below
for additional information.
- s5m8767,pmic-buck3-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
units for buck3 when changing voltage using gpio dvs. Refer to [1] below
for additional information.
- s5m8767,pmic-buck4-dvs-voltage: A set of 8 voltage values in micro-volt (uV)
units for buck4 when changing voltage using gpio dvs. Refer to [1] below
for additional information.
- s5m8767,pmic-buck-ds-gpios: GPIO specifiers for three host gpio's used
for selecting GPIO DVS lines. It is one-to-one mapped to dvs gpio lines.
[1] If none of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
property is specified, the 's5m8767,pmic-buck[2/3/4]-dvs-voltage'
property should specify atleast one voltage level (which would be a
safe operating voltage).
If either of the 's5m8767,pmic-buck[2/3/4]-uses-gpio-dvs' optional
property is specified, then all the eight voltage values for the
's5m8767,pmic-buck[2/3/4]-dvs-voltage' should be specified.
Optional properties:
- interrupt-parent: Specifies the phandle of the interrupt controller to which
the interrupts from s5m8767 are delivered to.
- interrupts: Interrupt specifiers for two interrupt sources.
- First interrupt specifier is for 'irq1' interrupt.
- Second interrupt specifier is for 'alert' interrupt.
- s5m8767,pmic-buck2-uses-gpio-dvs: 'buck2' can be controlled by gpio dvs.
- s5m8767,pmic-buck3-uses-gpio-dvs: 'buck3' can be controlled by gpio dvs.
- s5m8767,pmic-buck4-uses-gpio-dvs: 'buck4' can be controlled by gpio dvs.
Additional properties required if either of the optional properties are used:
- s5m8767,pmic-buck234-default-dvs-idx: Default voltage setting selected from
the possible 8 options selectable by the dvs gpios. The value of this
property should be between 0 and 7. If not specified or if out of range, the
default value of this property is set to 0.
- s5m8767,pmic-buck-dvs-gpios: GPIO specifiers for three host gpio's used
for dvs. The format of the gpio specifier depends in the gpio controller.
Regulators: The regulators of s5m8767 that have to be instantiated should be
included in a sub-node named 'regulators'. Regulator nodes included in this
sub-node should be of the format as listed below.
regulator_name {
ldo1_reg: LDO1 {
regulator-name = "VDD_ALIVE_1.0V";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-always-on;
regulator-boot-on;
op_mode = <1>; /* Normal Mode */
};
};
The above regulator entries are defined in regulator bindings documentation
except op_mode description.
- op_mode: describes the different operating modes of the LDO's with
power mode change in SOC. The different possible values are,
0 - always off mode
1 - on in normal mode
2 - low power mode
3 - suspend mode
The following are the names of the regulators that the s5m8767 pmic block
supports. Note: The 'n' in LDOn and BUCKn represents the LDO or BUCK number
as per the datasheet of s5m8767.
- LDOn
- valid values for n are 1 to 28
- Example: LDO0, LD01, LDO28
- BUCKn
- valid values for n are 1 to 9.
- Example: BUCK1, BUCK2, BUCK9
The bindings inside the regulator nodes use the standard regulator bindings
which are documented elsewhere.
Example:
s5m8767_pmic@66 {
compatible = "samsung,s5m8767-pmic";
reg = <0x66>;
s5m8767,pmic-buck2-uses-gpio-dvs;
s5m8767,pmic-buck3-uses-gpio-dvs;
s5m8767,pmic-buck4-uses-gpio-dvs;
s5m8767,pmic-buck-default-dvs-idx = <0>;
s5m8767,pmic-buck-dvs-gpios = <&gpx0 0 0>, /* DVS1 */
<&gpx0 1 0>, /* DVS2 */
<&gpx0 2 0>; /* DVS3 */
s5m8767,pmic-buck-ds-gpios = <&gpx2 3 0>, /* SET1 */
<&gpx2 4 0>, /* SET2 */
<&gpx2 5 0>; /* SET3 */
s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>,
<1250000>, <1200000>,
<1150000>, <1100000>,
<1000000>, <950000>;
s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>,
<1100000>, <1100000>,
<1000000>, <1000000>,
<1000000>, <1000000>;
s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>,
<1200000>, <1200000>,
<1200000>, <1200000>,
<1200000>, <1200000>;
regulators {
ldo1_reg: LDO1 {
regulator-name = "VDD_ABB_3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
op_mode = <1>; /* Normal Mode */
};
ldo2_reg: LDO2 {
regulator-name = "VDD_ALIVE_1.1V";
regulator-min-microvolt = <1100000>;
regulator-max-microvolt = <1100000>;
regulator-always-on;
};
buck1_reg: BUCK1 {
regulator-name = "VDD_MIF_1.2V";
regulator-min-microvolt = <950000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
regulator-boot-on;
};
};
};
|
