/*- * Copyright (c) 2002-2005 Sam Leffler, Errno Consulting * Copyright (c) 2004-2005 Atheros Communications, Inc. * Copyright (c) 2006 Devicescape Software, Inc. * Copyright (c) 2007 Jiri Slaby * Copyright (c) 2007 Luis R. Rodriguez * * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the above copyright * notice, this list of conditions and the following disclaimer, * without modification. * 2. Redistributions in binary form must reproduce at minimum a disclaimer * similar to the "NO WARRANTY" disclaimer below ("Disclaimer") and any * redistribution must be conditioned upon including a substantially * similar Disclaimer requirement for further binary redistribution. * 3. Neither the names of the above-listed copyright holders nor the names * of any contributors may be used to endorse or promote products derived * from this software without specific prior written permission. * * Alternatively, this software may be distributed under the terms of the * GNU General Public License ("GPL") version 2 as published by the Free * Software Foundation. * * NO WARRANTY * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS * ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT * LIMITED TO, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTIBILITY * AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL * THE COPYRIGHT HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, * OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER * IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF * THE POSSIBILITY OF SUCH DAMAGES. * */ #include #include #include #include #include #include #include #include #include #include #include #include #include #include "base.h" #include "reg.h" #include "debug.h" #include "ani.h" static int modparam_nohwcrypt; module_param_named(nohwcrypt, modparam_nohwcrypt, bool, S_IRUGO); MODULE_PARM_DESC(nohwcrypt, "Disable hardware encryption."); static int modparam_all_channels; module_param_named(all_channels, modparam_all_channels, bool, S_IRUGO); MODULE_PARM_DESC(all_channels, "Expose all channels the device can use."); /******************\ * Internal defines * \******************/ /* Module info */ MODULE_AUTHOR("Jiri Slaby"); MODULE_AUTHOR("Nick Kossifidis"); MODULE_DESCRIPTION("Support for 5xxx series of Atheros 802.11 wireless LAN cards."); MODULE_SUPPORTED_DEVICE("Atheros 5xxx WLAN cards"); MODULE_LICENSE("Dual BSD/GPL"); MODULE_VERSION("0.6.0 (EXPERIMENTAL)"); /* Known PCI ids */ static DEFINE_PCI_DEVICE_TABLE(ath5k_pci_id_table) = { { PCI_VDEVICE(ATHEROS, 0x0207) }, /* 5210 early */ { PCI_VDEVICE(ATHEROS, 0x0007) }, /* 5210 */ { PCI_VDEVICE(ATHEROS, 0x0011) }, /* 5311 - this is on AHB bus !*/ { PCI_VDEVICE(ATHEROS, 0x0012) }, /* 5211 */ { PCI_VDEVICE(ATHEROS, 0x0013) }, /* 5212 */ { PCI_VDEVICE(3COM_2, 0x0013) }, /* 3com 5212 */ { PCI_VDEVICE(3COM, 0x0013) }, /* 3com 3CRDAG675 5212 */ { PCI_VDEVICE(ATHEROS, 0x1014) }, /* IBM minipci 5212 */ { PCI_VDEVICE(ATHEROS, 0x0014) }, /* 5212 combatible */ { PCI_VDEVICE(ATHEROS, 0x0015) }, /* 5212 combatible */ { PCI_VDEVICE(ATHEROS, 0x0016) }, /* 5212 combatible */ { PCI_VDEVICE(ATHEROS, 0x0017) }, /* 5212 combatible */ { PCI_VDEVICE(ATHEROS, 0x0018) }, /* 5212 combatible */ { PCI_VDEVICE(ATHEROS, 0x0019) }, /* 5212 combatible */ { PCI_VDEVICE(ATHEROS, 0x001a) }, /* 2413 Griffin-lite */ { PCI_VDEVICE(ATHEROS, 0x001b) }, /* 5413 Eagle */ { PCI_VDEVICE(ATHEROS, 0x001c) }, /* PCI-E cards */ { PCI_VDEVICE(ATHEROS, 0x001d) }, /* 2417 Nala */ { 0 } }; MODULE_DEVICE_TABLE(pci, ath5k_pci_id_table); /* Known SREVs */ static const struct ath5k_srev_name srev_names[] = { { "5210", AR5K_VERSION_MAC, AR5K_SREV_AR5210 }, { "5311", AR5K_VERSION_MAC, AR5K_SREV_AR5311 }, { "5311A", AR5K_VERSION_MAC, AR5K_SREV_AR5311A }, { "5311B", AR5K_VERSION_MAC, AR5K_SREV_AR5311B }, { "5211", AR5K_VERSION_MAC, AR5K_SREV_AR5211 }, { "5212", AR5K_VERSION_MAC, AR5K_SREV_AR5212 }, { "5213", AR5K_VERSION_MAC, AR5K_SREV_AR5213 }, { "5213A", AR5K_VERSION_MAC, AR5K_SREV_AR5213A }, { "2413", AR5K_VERSION_MAC, AR5K_SREV_AR2413 }, { "2414", AR5K_VERSION_MAC, AR5K_SREV_AR2414 }, { "5424", AR5K_VERSION_MAC, AR5K_SREV_AR5424 }, { "5413", AR5K_VERSION_MAC, AR5K_SREV_AR5413 }, { "5414", AR5K_VERSION_MAC, AR5K_SREV_AR5414 }, { "2415", AR5K_VERSION_MAC, AR5K_SREV_AR2415 }, { "5416", AR5K_VERSION_MAC, AR5K_SREV_AR5416 }, { "5418", AR5K_VERSION_MAC, AR5K_SREV_AR5418 }, { "2425", AR5K_VERSION_MAC, AR5K_SREV_AR2425 }, { "2417", AR5K_VERSION_MAC, AR5K_SREV_AR2417 }, { "xxxxx", AR5K_VERSION_MAC, AR5K_SREV_UNKNOWN }, { "5110", AR5K_VERSION_RAD, AR5K_SREV_RAD_5110 }, { "5111", AR5K_VERSION_RAD, AR5K_SREV_RAD_5111 }, { "5111A", AR5K_VERSION_RAD, AR5K_SREV_RAD_5111A }, { "2111", AR5K_VERSION_RAD, AR5K_SREV_RAD_2111 }, { "5112", AR5K_VERSION_RAD, AR5K_SREV_RAD_5112 }, { "5112A", AR5K_VERSION_RAD, AR5K_SREV_RAD_5112A }, { "5112B", AR5K_VERSION_RAD, AR5K_SREV_RAD_5112B }, { "2112", AR5K_VERSION_RAD, AR5K_SREV_RAD_2112 }, { "2112A", AR5K_VERSION_RAD, AR5K_SREV_RAD_2112A }, { "2112B", AR5K_VERSION_RAD, AR5K_SREV_RAD_2112B }, { "2413", AR5K_VERSION_RAD, AR5K_SREV_RAD_2413 }, { "5413", AR5K_VERSION_RAD, AR5K_SREV_RAD_5413 }, { "2316", AR5K_VERSION_RAD, AR5K_SREV_RAD_2316 }, { "2317", AR5K_VERSION_RAD, AR5K_SREV_RAD_2317 }, { "5424", AR5K_VERSION_RAD, AR5K_SREV_RAD_5424 }, { "5133", AR5K_VERSION_RAD, AR5K_SREV_RAD_5133 }, { "xxxxx", AR5K_VERSION_RAD, AR5K_SREV_UNKNOWN }, }; static const struct ieee80211_rate ath5k_rates[] = { { .bitrate = 10, .hw_value = ATH5K_RATE_CODE_1M, }, { .bitrate = 20, .hw_value = ATH5K_RATE_CODE_2M, .hw_value_short = ATH5K_RATE_CODE_2M | AR5K_SET_SHORT_PREAMBLE, .flags = IEEE80211_RATE_SHORT_PREAMBLE }, { .bitrate = 55, .hw_value = ATH5K_RATE_CODE_5_5M, .hw_value_short = ATH5K_RATE_CODE_5_5M | AR5K_SET_SHORT_PREAMBLE, .flags = IEEE80211_RATE_SHORT_PREAMBLE }, { .bitrate = 110, .hw_value = ATH5K_RATE_CODE_11M, .hw_value_short = ATH5K_RATE_CODE_11M | AR5K_SET_SHORT_PREAMBLE, .flags = IEEE80211_RATE_SHORT_PREAMBLE }, { .bitrate = 60, .hw_value = ATH5K_RATE_CODE_6M, .flags = 0 }, { .bitrate = 90, .hw_value = ATH5K_RATE_CODE_9M, .flags = 0 }, { .bitrate = 120, .hw_value = ATH5K_RATE_CODE_12M, .flags = 0 }, { .bitrate = 180, .hw_value = ATH5K_RATE_CODE_18M, .flags = 0 }, { .bitrate = 240, .hw_value = ATH5K_RATE_CODE_24M, .flags = 0 }, { .bitrate = 360, .hw_value = ATH5K_RATE_CODE_36M, .flags = 0 }, { .bitrate = 480, .hw_value = ATH5K_RATE_CODE_48M, .flags = 0 }, { .bitrate = 540, .hw_value = ATH5K_RATE_CODE_54M, .flags = 0 }, /* XR missing */ }; /* * Prototypes - PCI stack related functions */ static int __devinit ath5k_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id); static void __devexit ath5k_pci_remove(struct pci_dev *pdev); #ifdef CONFIG_PM static int ath5k_pci_suspend(struct device *dev); static int ath5k_pci_resume(struct device *dev); static SIMPLE_DEV_PM_OPS(ath5k_pm_ops, ath5k_pci_suspend, ath5k_pci_resume); #define ATH5K_PM_OPS (&ath5k_pm_ops) #else #define ATH5K_PM_OPS NULL #endif /* CONFIG_PM */ static struct pci_driver ath5k_pci_driver = { .name = KBUILD_MODNAME, .id_table = ath5k_pci_id_table, .probe = ath5k_pci_probe, .remove = __devexit_p(ath5k_pci_remove), .driver.pm = ATH5K_PM_OPS, }; /* * Prototypes - MAC 802.11 stack related functions */ static int ath5k_tx(struct ieee80211_hw *hw, struct sk_buff *skb); static int ath5k_tx_queue(struct ieee80211_hw *hw, struct sk_buff *skb, struct ath5k_txq *txq); static int ath5k_reset(struct ath5k_softc *sc, struct ieee80211_channel *chan); static int ath5k_reset_wake(struct ath5k_softc *sc); static int ath5k_start(struct ieee80211_hw *hw); static void ath5k_stop(struct ieee80211_hw *hw); static int ath5k_add_interface(struct ieee80211_hw *hw, struct ieee80211_vif *vif); static void ath5k_remove_interface(struct ieee80211_hw *hw, struct ieee80211_vif *vif); static int ath5k_config(struct ieee80211_hw *hw, u32 changed); static u64 ath5k_prepare_multicast(struct ieee80211_hw *hw, struct netdev_hw_addr_list *mc_list); static void ath5k_configure_filter(struct ieee80211_hw *hw, unsigned int changed_flags, unsigned int *new_flags, u64 multicast); static int ath5k_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd, struct ieee80211_vif *vif, struct ieee80211_sta *sta, struct ieee80211_key_conf *key); static int ath5k_get_stats(struct ieee80211_hw *hw, struct ieee80211_low_level_stats *stats); static int ath5k_get_survey(struct ieee80211_hw *hw, int idx, struct survey_info *survey); static u64 ath5k_get_tsf(struct ieee80211_hw *hw); static void ath5k_set_tsf(struct ieee80211_hw *hw, u64 tsf); static void ath5k_reset_tsf(struct ieee80211_hw *hw); static int ath5k_beacon_update(struct ieee80211_hw *hw, struct ieee80211_vif *vif); static void ath5k_bss_info_changed(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct ieee80211_bss_conf *bss_conf, u32 changes); static void ath5k_sw_scan_start(struct ieee80211_hw *hw); static void ath5k_sw_scan_complete(struct ieee80211_hw *hw); static void ath5k_set_coverage_class(struct ieee80211_hw *hw, u8 coverage_class); static const struct ieee80211_ops ath5k_hw_ops = { .tx = ath5k_tx, .start = ath5k_start, .stop = ath5k_stop, .add_interface = ath5k_add_interface, .remove_interface = ath5k_remove_interface, .config = ath5k_config, .prepare_multicast = ath5k_prepare_multicast, .configure_filter = ath5k_configure_filter, .set_key = ath5k_set_key, .get_stats = ath5k_get_stats, .get_survey = ath5k_get_survey, .conf_tx = NULL, .get_tsf = ath5k_get_tsf, .set_tsf = ath5k_set_tsf, .reset_tsf = ath5k_reset_tsf, .bss_info_changed = ath5k_bss_info_changed, .sw_scan_start = ath5k_sw_scan_start, .sw_scan_complete = ath5k_sw_scan_complete, .set_coverage_class = ath5k_set_coverage_class, }; /* * Prototypes - Internal functions */ /* Attach detach */ static int ath5k_attach(struct pci_dev *pdev, struct ieee80211_hw *hw); static void ath5k_detach(struct pci_dev *pdev, struct ieee80211_hw *hw); /* Channel/mode setup */ static inline short ath5k_ieee2mhz(short chan); static unsigned int ath5k_copy_channels(struct ath5k_hw *ah, struct ieee80211_channel *channels, unsigned int mode, unsigned int max); static int ath5k_setup_bands(struct ieee80211_hw *hw); static int ath5k_chan_set(struct ath5k_softc *sc, struct ieee80211_channel *chan); static void ath5k_setcurmode(struct ath5k_softc *sc, unsigned int mode); static void ath5k_mode_setup(struct ath5k_softc *sc); /* Descriptor setup */ static int ath5k_desc_alloc(struct ath5k_softc *sc, struct pci_dev *pdev); static void ath5k_desc_free(struct ath5k_softc *sc, struct pci_dev *pdev); /* Buffers setup */ static int ath5k_rxbuf_setup(struct ath5k_softc *sc, struct ath5k_buf *bf); static int ath5k_txbuf_setup(struct ath5k_softc *sc, struct ath5k_buf *bf, struct ath5k_txq *txq, int padsize); static inline void ath5k_txbuf_free(struct ath5k_softc *sc, struct ath5k_buf *bf) { BUG_ON(!bf); if (!bf->skb) return; pci_unmap_single(sc->pdev, bf->skbaddr, bf->skb->len, PCI_DMA_TODEVICE); dev_kfree_skb_any(bf->skb); bf->skb = NULL; } static inline void ath5k_rxbuf_free(struct ath5k_softc *sc, struct ath5k_buf *bf) { struct ath5k_hw *ah = sc->ah; struct ath_common *common = ath5k_hw_common(ah); BUG_ON(!bf); if (!bf->skb) return; pci_unmap_single(sc->pdev, bf->skbaddr, common->rx_bufsize, PCI_DMA_FROMDEVICE); dev_kfree_skb_any(bf->skb); bf->skb = NULL; } /* Queues setup */ static struct ath5k_txq *ath5k_txq_setup(struct ath5k_softc *sc, int qtype, int subtype); static int ath5k_beaconq_setup(struct ath5k_hw *ah); static int ath5k_beaconq_config(struct ath5k_softc *sc); static void ath5k_txq_drainq(struct ath5k_softc *sc, struct ath5k_txq *txq); static void ath5k_txq_cleanup(struct ath5k_softc *sc); static void ath5k_txq_release(struct ath5k_softc *sc); /* Rx handling */ static int ath5k_rx_start(struct ath5k_softc *sc); static void ath5k_rx_stop(struct ath5k_softc *sc); static unsigned int ath5k_rx_decrypted(struct ath5k_softc *sc, struct ath5k_desc *ds, struct sk_buff *skb, struct ath5k_rx_status *rs); static void ath5k_tasklet_rx(unsigned long data); /* Tx handling */ static void ath5k_tx_processq(struct ath5k_softc *sc, struct ath5k_txq *txq); static void ath5k_tasklet_tx(unsigned long data); /* Beacon handling */ static int ath5k_beacon_setup(struct ath5k_softc *sc, struct ath5k_buf *bf); static void ath5k_beacon_send(struct ath5k_softc *sc); static void ath5k_beacon_config(struct ath5k_softc *sc); static void ath5k_beacon_update_timers(struct ath5k_softc *sc, u64 bc_tsf); static void ath5k_tasklet_beacon(unsigned long data); static void ath5k_tasklet_ani(unsigned long data); static inline u64 ath5k_extend_tsf(struct ath5k_hw *ah, u32 rstamp) { u64 tsf = ath5k_hw_get_tsf64(ah); if ((tsf & 0x7fff) < rstamp) tsf -= 0x8000; return (tsf & ~0x7fff) | rstamp; } /* Interrupt handling */ static int ath5k_init(struct ath5k_softc *sc); static int ath5k_stop_locked(struct ath5k_softc *sc); static int ath5k_stop_hw(struct ath5k_softc *sc); static irqreturn_t ath5k_intr(int irq, void *dev_id); static void ath5k_tasklet_reset(unsigned long data); static void ath5k_tasklet_calibrate(unsigned long data); /* * Module init/exit functions */ static int __init init_ath5k_pci(void) { int ret; ath5k_debug_init(); ret = pci_register_driver(&ath5k_pci_driver); if (ret) { printk(KERN_ERR "ath5k_pci: can't register pci driver\n"); return ret; } return 0; } static void __exit exit_ath5k_pci(void) { pci_unregister_driver(&ath5k_pci_driver); ath5k_debug_finish(); } module_init(init_ath5k_pci); module_exit(exit_ath5k_pci); /********************\ * PCI Initialization * \********************/ static const char * ath5k_chip_name(enum ath5k_srev_type type, u_int16_t val) { const char *name = "xxxxx"; unsigned int i; for (i = 0; i < ARRAY_SIZE(srev_names); i++) { if (srev_names[i].sr_type != type) continue; if ((val & 0xf0) == srev_names[i].sr_val) name = srev_names[i].sr_name; if ((val & 0xff) == srev_names[i].sr_val) { name = srev_names[i].sr_name; break; } } return name; } static unsigned int ath5k_ioread32(void *hw_priv, u32 reg_offset) { struct ath5k_hw *ah = (struct ath5k_hw *) hw_priv; return ath5k_hw_reg_read(ah, reg_offset); } static void ath5k_iowrite32(void *hw_priv, u32 val, u32 reg_offset) { struct ath5k_hw *ah = (struct ath5k_hw *) hw_priv; ath5k_hw_reg_write(ah, val, reg_offset); } static const struct ath_ops ath5k_common_ops = { .read = ath5k_ioread32, .write = ath5k_iowrite32, }; static int __devinit ath5k_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id) { void __iomem *mem; struct ath5k_softc *sc; struct ath_common *common; struct ieee80211_hw *hw; int ret; u8 csz; ret = pci_enable_device(pdev); if (ret) { dev_err(&pdev->dev, "can't enable device\n"); goto err; } /* XXX 32-bit addressing only */ ret = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)); if (ret) { dev_err(&pdev->dev, "32-bit DMA not available\n"); goto err_dis; } /* * Cache line size is used to size and align various * structures used to communicate with the hardware. */ pci_read_config_byte(pdev, PCI_CACHE_LINE_SIZE, &csz); if (csz == 0) { /* * Linux 2.4.18 (at least) writes the cache line size * register as a 16-bit wide register which is wrong. * We must have this setup properly for rx buffer * DMA to work so force a reasonable value here if it * comes up zero. */ csz = L1_CACHE_BYTES >> 2; pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, csz); } /* * The default setting of latency timer yields poor results, * set it to the value used by other systems. It may be worth * tweaking this setting more. */ pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0xa8); /* Enable bus mastering */ pci_set_master(pdev); /* * Disable the RETRY_TIMEOUT register (0x41) to keep * PCI Tx retries from interfering with C3 CPU state. */ pci_write_config_byte(pdev, 0x41, 0); ret = pci_request_region(pdev, 0, "ath5k"); if (ret) { dev_err(&pdev->dev, "cannot reserve PCI memory region\n"); goto err_dis; } mem = pci_iomap(pdev, 0, 0); if (!mem) { dev_err(&pdev->dev, "cannot remap PCI memory region\n") ; ret = -EIO; goto err_reg; } /* * Allocate hw (mac80211 main struct) * and hw->priv (driver private data) */ hw = ieee80211_alloc_hw(sizeof(*sc), &ath5k_hw_ops); if (hw == NULL) { dev_err(&pdev->dev, "cannot allocate ieee80211_hw\n"); ret = -ENOMEM; goto err_map; } dev_info(&pdev->dev, "registered as '%s'\n", wiphy_name(hw->wiphy)); /* Initialize driver private data */ SET_IEEE80211_DEV(hw, &pdev->dev); hw->flags = IEEE80211_HW_RX_INCLUDES_FCS | IEEE80211_HW_HOST_BROADCAST_PS_BUFFERING | IEEE80211_HW_SIGNAL_DBM | IEEE80211_HW_NOISE_DBM; hw->wiphy->interface_modes = BIT(NL80211_IFTYPE_AP) | BIT(NL80211_IFTYPE_STATION) | BIT(NL80211_IFTYPE_ADHOC) | BIT(NL80211_IFTYPE_MESH_POINT); hw->extra_tx_headroom = 2; hw->channel_change_time = 5000; sc = hw->priv; sc->hw = hw; sc->pdev = pdev; ath5k_debug_init_device(sc); /* * Mark the device as detached to avoid processing * interrupts until setup is complete. */ __set_bit(ATH_STAT_INVALID, sc->status); sc->iobase = mem; /* So we can unmap it on detach */ sc->opmode = NL80211_IFTYPE_STATION; sc->bintval = 1000; mutex_init(&sc->lock); spin_lock_init(&sc->rxbuflock); spin_lock_init(&sc->txbuflock); spin_lock_init(&sc->block); /* Set private data */ pci_set_drvdata(pdev, hw); /* Setup interrupt handler */ ret = request_irq(pdev->irq, ath5k_intr, IRQF_SHARED, "ath", sc); if (ret) { ATH5K_ERR(sc, "request_irq failed\n"); goto err_free; } /*If we passed the test malloc a ath5k_hw struct*/ sc->ah = kzalloc(sizeof(struct ath5k_hw), GFP_KERNEL); if (!sc->ah) { ret = -ENOMEM; ATH5K_ERR(sc, "out of memory\n"); goto err_irq; } sc->ah->ah_sc = sc; sc->ah->ah_iobase = sc->iobase; common = ath5k_hw_common(sc->ah); common->ops = &ath5k_common_ops; common->ah = sc->ah; common->hw = hw; common->cachelsz = csz << 2; /* convert to bytes */ /* Initialize device */ ret = ath5k_hw_attach(sc); if (ret) { goto err_free_ah; } /* set up multi-rate retry capabilities */ if (sc->ah->ah_version == AR5K_AR5212) { hw->max_rates = 4; hw->max_rate_tries = 11; } /* Finish private driver data initialization */ ret = ath5k_attach(pdev, hw); if (ret) goto err_ah; ATH5K_INFO(sc, "Atheros AR%s chip found (MAC: 0x%x, PHY: 0x%x)\n", ath5k_chip_name(AR5K_VERSION_MAC, sc->ah->ah_mac_srev), sc->ah->ah_mac_srev, sc->ah->ah_phy_revision); if (!sc->ah->ah_single_chip) { /* Single chip radio (!RF5111) */ if (sc->ah->ah_radio_5ghz_revision && !sc->ah->ah_radio_2ghz_revision) { /* No 5GHz support -> report 2GHz radio */ if (!test_bit(AR5K_MODE_11A, sc->ah->ah_capabilities.cap_mode)) { ATH5K_INFO(sc, "RF%s 2GHz radio found (0x%x)\n", ath5k_chip_name(AR5K_VERSION_RAD, sc->ah->ah_radio_5ghz_revision), sc->ah->ah_radio_5ghz_revision); /* No 2GHz support (5110 and some * 5Ghz only cards) -> report 5Ghz radio */ } else if (!test_bit(AR5K_MODE_11B, sc->ah->ah_capabilities.cap_mode)) { ATH5K_INFO(sc, "RF%s 5GHz radio found (0x%x)\n", ath5k_chip_name(AR5K_VERSION_RAD, sc->ah->ah_radio_5ghz_revision), sc->ah->ah_radio_5ghz_revision); /* Multiband radio */ } else { ATH5K_INFO(sc, "RF%s multiband radio found" " (0x%x)\n", ath5k_chip_name(AR5K_VERSION_RAD, sc->ah->ah_radio_5ghz_revision), sc->ah->ah_radio_5ghz_revision); } } /* Multi chip radio (RF5111 - RF2111) -> * report both 2GHz/5GHz radios */ else if (sc->ah->ah_radio_5ghz_revision && sc->ah->ah_radio_2ghz_revision){ ATH5K_INFO(sc, "RF%s 5GHz radio found (0x%x)\n", ath5k_chip_name(AR5K_VERSION_RAD, sc->ah->ah_radio_5ghz_revision), sc->ah->ah_radio_5ghz_revision); ATH5K_INFO(sc, "RF%s 2GHz radio found (0x%x)\n", ath5k_chip_name(AR5K_VERSION_RAD, sc->ah->ah_radio_2ghz_revision), sc->ah->ah_radio_2ghz_revision); } } /* ready to process interrupts */ __clear_bit(ATH_STAT_INVALID, sc->status); return 0; err_ah: ath5k_hw_detach(sc->ah); err_irq: free_irq(pdev->irq, sc); err_free_ah: kfree(sc->ah); err_free: ieee80211_free_hw(hw); err_map: pci_iounmap(pdev, mem); err_reg: pci_release_region(pdev, 0); err_dis: pci_disable_device(pdev); err: return ret; } static void __devexit ath5k_pci_remove(struct pci_dev *pdev) { struct ieee80211_hw *hw = pci_get_drvdata(pdev); struct ath5k_softc *sc = hw->priv; ath5k_debug_finish_device(sc); ath5k_detach(pdev, hw); ath5k_hw_detach(sc->ah); kfree(sc->ah); free_irq(pdev->irq, sc); pci_iounmap(pdev, sc->iobase); pci_release_region(pdev, 0); pci_disable_device(pdev); ieee80211_free_hw(hw); } #ifdef CONFIG_PM static int ath5k_pci_suspend(struct device *dev) { struct ieee80211_hw *hw = pci_get_drvdata(to_pci_dev(dev)); struct ath5k_softc *sc = hw->priv; ath5k_led_off(sc); return 0; } static int ath5k_pci_resume(struct device *dev) { struct pci_dev *pdev = to_pci_dev(dev); struct ieee80211_hw *hw = pci_get_drvdata(pdev); struct ath5k_softc *sc = hw->priv; /* * Suspend/Resume resets the PCI configuration space, so we have to * re-disable the RETRY_TIMEOUT register (0x41) to keep * PCI Tx retries from interfering with C3 CPU state */ pci_write_config_byte(pdev, 0x41, 0); ath5k_led_enable(sc); return 0; } #endif /* CONFIG_PM */ /***********************\ * Driver Initialization * \***********************/ static int ath5k_reg_notifier(struct wiphy *wiphy, struct regulatory_request *request) { struct ieee80211_hw *hw = wiphy_to_ieee80211_hw(wiphy); struct ath5k_softc *sc = hw->priv; struct ath_regulatory *regulatory = ath5k_hw_regulatory(sc->ah); return ath_reg_notifier_apply(wiphy, request, regulatory); } static int ath5k_attach(struct pci_dev *pdev, struct ieee80211_hw *hw) { struct ath5k_softc *sc = hw->priv; struct ath5k_hw *ah = sc->ah; struct ath_regulatory *regulatory = ath5k_hw_regulatory(ah); u8 mac[ETH_ALEN] = {}; int ret; ATH5K_DBG(sc, ATH5K_DEBUG_ANY, "devid 0x%x\n", pdev->device); /* * Check if the MAC has multi-rate retry support. * We do this by trying to setup a fake extended * descriptor. MAC's that don't have support will * return false w/o doing anything. MAC's that do * support it will return true w/o doing anything. */ ret = ah->ah_setup_mrr_tx_desc(ah, NULL, 0, 0, 0, 0, 0, 0); if (ret < 0) goto err; if (ret > 0) __set_bit(ATH_STAT_MRRETRY, sc->status); /* * Collect the channel list. The 802.11 layer * is resposible for filtering this list based * on settings like the phy mode and regulatory * domain restrictions. */ ret = ath5k_setup_bands(hw); if (ret) { ATH5K_ERR(sc, "can't get channels\n"); goto err; } /* NB: setup here so ath5k_rate_update is happy */ if (test_bit(AR5K_MODE_11A, ah->ah_modes)) ath5k_setcurmode(sc, AR5K_MODE_11A); else ath5k_setcurmode(sc, AR5K_MODE_11B); /* * Allocate tx+rx descriptors and populate the lists. */ ret = ath5k_desc_alloc(sc, pdev); if (ret) { ATH5K_ERR(sc, "can't allocate descriptors\n"); goto err; } /* * Allocate hardware transmit queues: one queue for * beacon frames and one data queue for each QoS * priority. Note that hw functions handle reseting * these queues at the needed time. */ ret = ath5k_beaconq_setup(ah); if (ret < 0) { ATH5K_ERR(sc, "can't setup a beacon xmit queue\n"); goto err_desc; } sc->bhalq = ret; sc->cabq = ath5k_txq_setup(sc, AR5K_TX_QUEUE_CAB, 0); if (IS_ERR(sc->cabq)) { ATH5K_ERR(sc, "can't setup cab queue\n"); ret = PTR_ERR(sc->cabq); goto err_bhal; } sc->txq = ath5k_txq_setup(sc, AR5K_TX_QUEUE_DATA, AR5K_WME_AC_BK); if (IS_ERR(sc->txq)) { ATH5K_ERR(sc, "can't setup xmit queue\n"); ret = PTR_ERR(sc->txq); goto err_queues; } tasklet_init(&sc->rxtq, ath5k_tasklet_rx, (unsigned long)sc); tasklet_init(&sc->txtq, ath5k_tasklet_tx, (unsigned long)sc); tasklet_init(&sc->restq, ath5k_tasklet_reset, (unsigned long)sc); tasklet_init(&sc->calib, ath5k_tasklet_calibrate, (unsigned long)sc); tasklet_init(&sc->beacontq, ath5k_tasklet_beacon, (unsigned long)sc); tasklet_init(&sc->ani_tasklet, ath5k_tasklet_ani, (unsigned long)sc); ret = ath5k_eeprom_read_mac(ah, mac); if (ret) { ATH5K_ERR(sc, "unable to read address from EEPROM: 0x%04x\n", sc->pdev->device); goto err_queues; } SET_IEEE80211_PERM_ADDR(hw, mac); /* All MAC address bits matter for ACKs */ memcpy(sc->bssidmask, ath_bcast_mac, ETH_ALEN); ath5k_hw_set_bssid_mask(sc->ah, sc->bssidmask); regulatory->current_rd = ah->ah_capabilities.cap_eeprom.ee_regdomain; ret = ath_regd_init(regulatory, hw->wiphy, ath5k_reg_notifier); if (ret) { ATH5K_ERR(sc, "can't initialize regulatory system\n"); goto err_queues; } ret = ieee80211_register_hw(hw); if (ret) { ATH5K_ERR(sc, "can't register ieee80211 hw\n"); goto err_queues; } if (!ath_is_world_regd(regulatory)) regulatory_hint(hw->wiphy, regulatory->alpha2); ath5k_init_leds(sc); return 0; err_queues: ath5k_txq_release(sc); err_bhal: ath5k_hw_release_tx_queue(ah, sc->bhalq); err_desc: ath5k_desc_free(sc, pdev); err: return ret; } static void ath5k_detach(struct pci_dev *pdev, struct ieee80211_hw *hw) { struct ath5k_softc *sc = hw->priv; /* * NB: the order of these is important: * o call the 802.11 layer before detaching ath5k_hw to * insure callbacks into the driver to delete global * key cache entries can be handled * o reclaim the tx queue data structures after calling * the 802.11 layer as we'll get called back to reclaim * node state and potentially want to use them * o to cleanup the tx queues the hal is called, so detach * it last * XXX: ??? detach ath5k_hw ??? * Other than that, it's straightforward... */ ieee80211_unregister_hw(hw); ath5k_desc_free(sc, pdev); ath5k_txq_release(sc); ath5k_hw_release_tx_queue(sc->ah, sc->bhalq); ath5k_unregister_leds(sc); /* * NB: can't reclaim these until after ieee80211_ifdetach * returns because we'll get called back to reclaim node * state and potentially want to use them. */ } /********************\ * Channel/mode setup * \********************/ /* * Convert IEEE channel number to MHz frequency. */ static inline short ath5k_ieee2mhz(short chan) { if (chan <= 14 || chan >= 27) return ieee80211chan2mhz(chan); else return 2212 + chan * 20; } /* * Returns true for the channel numbers used without all_channels modparam. */ static bool ath5k_is_standard_channel(short chan) { return ((chan <= 14) || /* UNII 1,2 */ ((chan & 3) == 0 && chan >= 36 && chan <= 64) || /* midband */ ((chan & 3) == 0 && chan >= 100 && chan <= 140) || /* UNII-3 */ ((chan & 3) == 1 && chan >= 149 && chan <= 165)); } static unsigned int ath5k_copy_channels(struct ath5k_hw *ah, struct ieee80211_channel *channels, unsigned int mode, unsigned int max) { unsigned int i, count, size, chfreq, freq, ch; if (!test_bit(mode, ah->ah_modes)) return 0; switch (mode) { case AR5K_MODE_11A: case AR5K_MODE_11A_TURBO: /* 1..220, but 2GHz frequencies are filtered by check_channel */ size = 220 ; chfreq = CHANNEL_5GHZ; break; case AR5K_MODE_11B: case AR5K_MODE_11G: case AR5K_MODE_11G_TURBO: size = 26; chfreq = CHANNEL_2GHZ; break; default: ATH5K_WARN(ah->ah_sc, "bad mode, not copying channels\n"); return 0; } for (i = 0, count = 0; i < size && max > 0; i++) { ch = i + 1 ; freq = ath5k_ieee2mhz(ch); /* Check if channel is supported by the chipset */ if (!ath5k_channel_ok(ah, freq, chfreq)) continue; if (!modparam_all_channels && !ath5k_is_standard_channel(ch)) continue; /* Write channel info and increment counter */ channels[count].center_freq = freq; channels[count].band = (chfreq == CHANNEL_2GHZ) ? IEEE80211_BAND_2GHZ : IEEE80211_BAND_5GHZ; switch (mode) { case AR5K_MODE_11A: case AR5K_MODE_11G: channels[count].hw_value = chfreq | CHANNEL_OFDM; break; case AR5K_MODE_11A_TURBO: case AR5K_MODE_11G_TURBO: channels[count].hw_value = chfreq | CHANNEL_OFDM | CHANNEL_TURBO; break; case AR5K_MODE_11B: channels[count].hw_value = CHANNEL_B; } count++; max--; } return count; } static void ath5k_setup_rate_idx(struct ath5k_softc *sc, struct ieee80211_supported_band *b) { u8 i; for (i = 0; i < AR5K_MAX_RATES; i++) sc->rate_idx[b->band][i] = -1; for (i = 0; i < b->n_bitrates; i++) { sc->rate_idx[b->band][b->bitrates[i].hw_value] = i; if (b->bitrates[i].hw_value_short) sc->rate_idx[b->band][b->bitrates[i].hw_value_short] = i; } } static int ath5k_setup_bands(struct ieee80211_hw *hw) { struct ath5k_softc *sc = hw->priv; struct ath5k_hw *ah = sc->ah; struct ieee80211_supported_band *sband; int max_c, count_c = 0; int i; BUILD_BUG_ON(ARRAY_SIZE(sc->sbands) < IEEE80211_NUM_BANDS); max_c = ARRAY_SIZE(sc->channels); /* 2GHz band */ sband = &sc->sbands[IEEE80211_BAND_2GHZ]; sband->band = IEEE80211_BAND_2GHZ; sband->bitrates = &sc->rates[IEEE80211_BAND_2GHZ][0]; if (test_bit(AR5K_MODE_11G, sc->ah->ah_capabilities.cap_mode)) { /* G mode */ memcpy(sband->bitrates, &ath5k_rates[0], sizeof(struct ieee80211_rate) * 12); sband->n_bitrates = 12; sband->channels = sc->channels; sband->n_channels = ath5k_copy_channels(ah, sband->channels, AR5K_MODE_11G, max_c); hw->wiphy->bands[IEEE80211_BAND_2GHZ] = sband; count_c = sband->n_channels; max_c -= count_c; } else if (test_bit(AR5K_MODE_11B, sc->ah->ah_capabilities.cap_mode)) { /* B mode */ memcpy(sband->bitrates, &ath5k_rates[0], sizeof(struct ieee80211_rate) * 4); sband->n_bitrates = 4; /* 5211 only supports B rates and uses 4bit rate codes * (e.g normally we have 0x1B for 1M, but on 5211 we have 0x0B) * fix them up here: */ if (ah->ah_version == AR5K_AR5211) { for (i = 0; i < 4; i++) { sband->bitrates[i].hw_value = sband->bitrates[i].hw_value & 0xF; sband->bitrates[i].hw_value_short = sband->bitrates[i].hw_value_short & 0xF; } } sband->channels = sc->channels; sband->n_channels = ath5k_copy_channels(ah, sband->channels, AR5K_MODE_11B, max_c); hw->wiphy->bands[IEEE80211_BAND_2GHZ] = sband; count_c = sband->n_channels; max_c -= count_c; } ath5k_setup_rate_idx(sc, sband); /* 5GHz band, A mode */ if (test_bit(AR5K_MODE_11A, sc->ah->ah_capabilities.cap_mode)) { sband = &sc->sbands[IEEE80211_BAND_5GHZ]; sband->band = IEEE80211_BAND_5GHZ; sband->bitrates = &sc->rates[IEEE80211_BAND_5GHZ][0]; memcpy(sband->bitrates, &ath5k_rates[4], sizeof(struct ieee80211_rate) * 8); sband->n_bitrates = 8; sband->channels = &sc->channels[count_c]; sband->n_channels = ath5k_copy_channels(ah, sband->channels, AR5K_MODE_11A, max_c); hw->wiphy->bands[IEEE80211_BAND_5GHZ] = sband; } ath5k_setup_rate_idx(sc, sband); ath5k_debug_dump_bands(sc); return 0; } /* * Set/change channels. We always reset the chip. * To accomplish this we must first cleanup any pending DMA, * then restart stuff after a la ath5k_init. * * Called with sc->lock. */ static int ath5k_chan_set(struct ath5k_softc *sc, struct ieee80211_channel *chan) { ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "(%u MHz) -> (%u MHz)\n", sc->curchan->center_freq, chan->center_freq); /* * To switch channels clear any pending DMA operations; * wait long enough for the RX fifo to drain, reset the * hardware at the new frequency, and then re-enable * the relevant bits of the h/w. */ return ath5k_reset(sc, chan); } static void ath5k_setcurmode(struct ath5k_softc *sc, unsigned int mode) { sc->curmode = mode; if (mode == AR5K_MODE_11A) { sc->curband = &sc->sbands[IEEE80211_BAND_5GHZ]; } else { sc->curband = &sc->sbands[IEEE80211_BAND_2GHZ]; } } static void ath5k_mode_setup(struct ath5k_softc *sc) { struct ath5k_hw *ah = sc->ah; u32 rfilt; /* configure rx filter */ rfilt = sc->filter_flags; ath5k_hw_set_rx_filter(ah, rfilt); if (ath5k_hw_hasbssidmask(ah)) ath5k_hw_set_bssid_mask(ah, sc->bssidmask); /* configure operational mode */ ath5k_hw_set_opmode(ah, sc->opmode); ATH5K_DBG(sc, ATH5K_DEBUG_MODE, "mode setup opmode %d\n", sc->opmode); ATH5K_DBG(sc, ATH5K_DEBUG_MODE, "RX filter 0x%x\n", rfilt); } static inline int ath5k_hw_to_driver_rix(struct ath5k_softc *sc, int hw_rix) { int rix; /* return base rate on errors */ if (WARN(hw_rix < 0 || hw_rix >= AR5K_MAX_RATES, "hw_rix out of bounds: %x\n", hw_rix)) return 0; rix = sc->rate_idx[sc->curband->band][hw_rix]; if (WARN(rix < 0, "invalid hw_rix: %x\n", hw_rix)) rix = 0; return rix; } /***************\ * Buffers setup * \***************/ static struct sk_buff *ath5k_rx_skb_alloc(struct ath5k_softc *sc, dma_addr_t *skb_addr) { struct ath_common *common = ath5k_hw_common(sc->ah); struct sk_buff *skb; /* * Allocate buffer with headroom_needed space for the * fake physical layer header at the start. */ skb = ath_rxbuf_alloc(common, common->rx_bufsize, GFP_ATOMIC); if (!skb) { ATH5K_ERR(sc, "can't alloc skbuff of size %u\n", common->rx_bufsize); return NULL; } *skb_addr = pci_map_single(sc->pdev, skb->data, common->rx_bufsize, PCI_DMA_FROMDEVICE); if (unlikely(pci_dma_mapping_error(sc->pdev, *skb_addr))) { ATH5K_ERR(sc, "%s: DMA mapping failed\n", __func__); dev_kfree_skb(skb); return NULL; } return skb; } static int ath5k_rxbuf_setup(struct ath5k_softc *sc, struct ath5k_buf *bf) { struct ath5k_hw *ah = sc->ah; struct sk_buff *skb = bf->skb; struct ath5k_desc *ds; if (!skb) { skb = ath5k_rx_skb_alloc(sc, &bf->skbaddr); if (!skb) return -ENOMEM; bf->skb = skb; } /* * Setup descriptors. For receive we always terminate * the descriptor list with a self-linked entry so we'll * not get overrun under high load (as can happen with a * 5212 when ANI processing enables PHY error frames). * * To insure the last descriptor is self-linked we create * each descriptor as self-linked and add it to the end. As * each additional descriptor is added the previous self-linked * entry is ``fixed'' naturally. This should be safe even * if DMA is happening. When processing RX interrupts we * never remove/process the last, self-linked, entry on the * descriptor list. This insures the hardware always has * someplace to write a new frame. */ ds = bf->desc; ds->ds_link = bf->daddr; /* link to self */ ds->ds_data = bf->skbaddr; ah->ah_setup_rx_desc(ah, ds, skb_tailroom(skb), /* buffer size */ 0); if (sc->rxlink != NULL) *sc->rxlink = bf->daddr; sc->rxlink = &ds->ds_link; return 0; } static enum ath5k_pkt_type get_hw_packet_type(struct sk_buff *skb) { struct ieee80211_hdr *hdr; enum ath5k_pkt_type htype; __le16 fc; hdr = (struct ieee80211_hdr *)skb->data; fc = hdr->frame_control; if (ieee80211_is_beacon(fc)) htype = AR5K_PKT_TYPE_BEACON; else if (ieee80211_is_probe_resp(fc)) htype = AR5K_PKT_TYPE_PROBE_RESP; else if (ieee80211_is_atim(fc)) htype = AR5K_PKT_TYPE_ATIM; else if (ieee80211_is_pspoll(fc)) htype = AR5K_PKT_TYPE_PSPOLL; else htype = AR5K_PKT_TYPE_NORMAL; return htype; } static int ath5k_txbuf_setup(struct ath5k_softc *sc, struct ath5k_buf *bf, struct ath5k_txq *txq, int padsize) { struct ath5k_hw *ah = sc->ah; struct ath5k_desc *ds = bf->desc; struct sk_buff *skb = bf->skb; struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); unsigned int pktlen, flags, keyidx = AR5K_TXKEYIX_INVALID; struct ieee80211_rate *rate; unsigned int mrr_rate[3], mrr_tries[3]; int i, ret; u16 hw_rate; u16 cts_rate = 0; u16 duration = 0; u8 rc_flags; flags = AR5K_TXDESC_INTREQ | AR5K_TXDESC_CLRDMASK; /* XXX endianness */ bf->skbaddr = pci_map_single(sc->pdev, skb->data, skb->len, PCI_DMA_TODEVICE); rate = ieee80211_get_tx_rate(sc->hw, info); if (info->flags & IEEE80211_TX_CTL_NO_ACK) flags |= AR5K_TXDESC_NOACK; rc_flags = info->control.rates[0].flags; hw_rate = (rc_flags & IEEE80211_TX_RC_USE_SHORT_PREAMBLE) ? rate->hw_value_short : rate->hw_value; pktlen = skb->len; /* FIXME: If we are in g mode and rate is a CCK rate * subtract ah->ah_txpower.txp_cck_ofdm_pwr_delta * from tx power (value is in dB units already) */ if (info->control.hw_key) { keyidx = info->control.hw_key->hw_key_idx; pktlen += info->control.hw_key->icv_len; } if (rc_flags & IEEE80211_TX_RC_USE_RTS_CTS) { flags |= AR5K_TXDESC_RTSENA; cts_rate = ieee80211_get_rts_cts_rate(sc->hw, info)->hw_value; duration = le16_to_cpu(ieee80211_rts_duration(sc->hw, sc->vif, pktlen, info)); } if (rc_flags & IEEE80211_TX_RC_USE_CTS_PROTECT) { flags |= AR5K_TXDESC_CTSENA; cts_rate = ieee80211_get_rts_cts_rate(sc->hw, info)->hw_value; duration = le16_to_cpu(ieee80211_ctstoself_duration(sc->hw, sc->vif, pktlen, info)); } ret = ah->ah_setup_tx_desc(ah, ds, pktlen, ieee80211_get_hdrlen_from_skb(skb), padsize, get_hw_packet_type(skb), (sc->power_level * 2), hw_rate, info->control.rates[0].count, keyidx, ah->ah_tx_ant, flags, cts_rate, duration); if (ret) goto err_unmap; memset(mrr_rate, 0, sizeof(mrr_rate)); memset(mrr_tries, 0, sizeof(mrr_tries)); for (i = 0; i < 3; i++) { rate = ieee80211_get_alt_retry_rate(sc->hw, info, i); if (!rate) break; mrr_rate[i] = rate->hw_value; mrr_tries[i] = info->control.rates[i + 1].count; } ah->ah_setup_mrr_tx_desc(ah, ds, mrr_rate[0], mrr_tries[0], mrr_rate[1], mrr_tries[1], mrr_rate[2], mrr_tries[2]); ds->ds_link = 0; ds->ds_data = bf->skbaddr; spin_lock_bh(&txq->lock); list_add_tail(&bf->list, &txq->q); if (txq->link == NULL) /* is this first packet? */ ath5k_hw_set_txdp(ah, txq->qnum, bf->daddr); else /* no, so only link it */ *txq->link = bf->daddr; txq->link = &ds->ds_link; ath5k_hw_start_tx_dma(ah, txq->qnum); mmiowb(); spin_unlock_bh(&txq->lock); return 0; err_unmap: pci_unmap_single(sc->pdev, bf->skbaddr, skb->len, PCI_DMA_TODEVICE); return ret; } /*******************\ * Descriptors setup * \*******************/ static int ath5k_desc_alloc(struct ath5k_softc *sc, struct pci_dev *pdev) { struct ath5k_desc *ds; struct ath5k_buf *bf; dma_addr_t da; unsigned int i; int ret; /* allocate descriptors */ sc->desc_len = sizeof(struct ath5k_desc) * (ATH_TXBUF + ATH_RXBUF + ATH_BCBUF + 1); sc->desc = pci_alloc_consistent(pdev, sc->desc_len, &sc->desc_daddr); if (sc->desc == NULL) { ATH5K_ERR(sc, "can't allocate descriptors\n"); ret = -ENOMEM; goto err; } ds = sc->desc; da = sc->desc_daddr; ATH5K_DBG(sc, ATH5K_DEBUG_ANY, "DMA map: %p (%zu) -> %llx\n", ds, sc->desc_len, (unsigned long long)sc->desc_daddr); bf = kcalloc(1 + ATH_TXBUF + ATH_RXBUF + ATH_BCBUF, sizeof(struct ath5k_buf), GFP_KERNEL); if (bf == NULL) { ATH5K_ERR(sc, "can't allocate bufptr\n"); ret = -ENOMEM; goto err_free; } sc->bufptr = bf; INIT_LIST_HEAD(&sc->rxbuf); for (i = 0; i < ATH_RXBUF; i++, bf++, ds++, da += sizeof(*ds)) { bf->desc = ds; bf->daddr = da; list_add_tail(&bf->list, &sc->rxbuf); } INIT_LIST_HEAD(&sc->txbuf); sc->txbuf_len = ATH_TXBUF; for (i = 0; i < ATH_TXBUF; i++, bf++, ds++, da += sizeof(*ds)) { bf->desc = ds; bf->daddr = da; list_add_tail(&bf->list, &sc->txbuf); } /* beacon buffer */ bf->desc = ds; bf->daddr = da; sc->bbuf = bf; return 0; err_free: pci_free_consistent(pdev, sc->desc_len, sc->desc, sc->desc_daddr); err: sc->desc = NULL; return ret; } static void ath5k_desc_free(struct ath5k_softc *sc, struct pci_dev *pdev) { struct ath5k_buf *bf; ath5k_txbuf_free(sc, sc->bbuf); list_for_each_entry(bf, &sc->txbuf, list) ath5k_txbuf_free(sc, bf); list_for_each_entry(bf, &sc->rxbuf, list) ath5k_rxbuf_free(sc, bf); /* Free memory associated with all descriptors */ pci_free_consistent(pdev, sc->desc_len, sc->desc, sc->desc_daddr); kfree(sc->bufptr); sc->bufptr = NULL; } /**************\ * Queues setup * \**************/ static struct ath5k_txq * ath5k_txq_setup(struct ath5k_softc *sc, int qtype, int subtype) { struct ath5k_hw *ah = sc->ah; struct ath5k_txq *txq; struct ath5k_txq_info qi = { .tqi_subtype = subtype, .tqi_aifs = AR5K_TXQ_USEDEFAULT, .tqi_cw_min = AR5K_TXQ_USEDEFAULT, .tqi_cw_max = AR5K_TXQ_USEDEFAULT }; int qnum; /* * Enable interrupts only for EOL and DESC conditions. * We mark tx descriptors to receive a DESC interrupt * when a tx queue gets deep; otherwise waiting for the * EOL to reap descriptors. Note that this is done to * reduce interrupt load and this only defers reaping * descriptors, never transmitting frames. Aside from * reducing interrupts this also permits more concurrency. * The only potential downside is if the tx queue backs * up in which case the top half of the kernel may backup * due to a lack of tx descriptors. */ qi.tqi_flags = AR5K_TXQ_FLAG_TXEOLINT_ENABLE | AR5K_TXQ_FLAG_TXDESCINT_ENABLE; qnum = ath5k_hw_setup_tx_queue(ah, qtype, &qi); if (qnum < 0) { /* * NB: don't print a message, this happens * normally on parts with too few tx queues */ return ERR_PTR(qnum); } if (qnum >= ARRAY_SIZE(sc->txqs)) { ATH5K_ERR(sc, "hw qnum %u out of range, max %tu!\n", qnum, ARRAY_SIZE(sc->txqs)); ath5k_hw_release_tx_queue(ah, qnum); return ERR_PTR(-EINVAL); } txq = &sc->txqs[qnum]; if (!txq->setup) { txq->qnum = qnum; txq->link = NULL; INIT_LIST_HEAD(&txq->q); spin_lock_init(&txq->lock); txq->setup = true; } return &sc->txqs[qnum]; } static int ath5k_beaconq_setup(struct ath5k_hw *ah) { struct ath5k_txq_info qi = { .tqi_aifs = AR5K_TXQ_USEDEFAULT, .tqi_cw_min = AR5K_TXQ_USEDEFAULT, .tqi_cw_max = AR5K_TXQ_USEDEFAULT, /* NB: for dynamic turbo, don't enable any other interrupts */ .tqi_flags = AR5K_TXQ_FLAG_TXDESCINT_ENABLE }; return ath5k_hw_setup_tx_queue(ah, AR5K_TX_QUEUE_BEACON, &qi); } static int ath5k_beaconq_config(struct ath5k_softc *sc) { struct ath5k_hw *ah = sc->ah; struct ath5k_txq_info qi; int ret; ret = ath5k_hw_get_tx_queueprops(ah, sc->bhalq, &qi); if (ret) goto err; if (sc->opmode == NL80211_IFTYPE_AP || sc->opmode == NL80211_IFTYPE_MESH_POINT) { /* * Always burst out beacon and CAB traffic * (aifs = cwmin = cwmax = 0) */ qi.tqi_aifs = 0; qi.tqi_cw_min = 0; qi.tqi_cw_max = 0; } else if (sc->opmode == NL80211_IFTYPE_ADHOC) { /* * Adhoc mode; backoff between 0 and (2 * cw_min). */ qi.tqi_aifs = 0; qi.tqi_cw_min = 0; qi.tqi_cw_max = 2 * ah->ah_cw_min; } ATH5K_DBG(sc, ATH5K_DEBUG_BEACON, "beacon queueprops tqi_aifs:%d tqi_cw_min:%d tqi_cw_max:%d\n", qi.tqi_aifs, qi.tqi_cw_min, qi.tqi_cw_max); ret = ath5k_hw_set_tx_queueprops(ah, sc->bhalq, &qi); if (ret) { ATH5K_ERR(sc, "%s: unable to update parameters for beacon " "hardware queue!\n", __func__); goto err; } ret = ath5k_hw_reset_tx_queue(ah, sc->bhalq); /* push to h/w */ if (ret) goto err; /* reconfigure cabq with ready time to 80% of beacon_interval */ ret = ath5k_hw_get_tx_queueprops(ah, AR5K_TX_QUEUE_ID_CAB, &qi); if (ret) goto err; qi.tqi_ready_time = (sc->bintval * 80) / 100; ret = ath5k_hw_set_tx_queueprops(ah, AR5K_TX_QUEUE_ID_CAB, &qi); if (ret) goto err; ret = ath5k_hw_reset_tx_queue(ah, AR5K_TX_QUEUE_ID_CAB); err: return ret; } static void ath5k_txq_drainq(struct ath5k_softc *sc, struct ath5k_txq *txq) { struct ath5k_buf *bf, *bf0; /* * NB: this assumes output has been stopped and * we do not need to block ath5k_tx_tasklet */ spin_lock_bh(&txq->lock); list_for_each_entry_safe(bf, bf0, &txq->q, list) { ath5k_debug_printtxbuf(sc, bf); ath5k_txbuf_free(sc, bf); spin_lock_bh(&sc->txbuflock); list_move_tail(&bf->list, &sc->txbuf); sc->txbuf_len++; spin_unlock_bh(&sc->txbuflock); } txq->link = NULL; spin_unlock_bh(&txq->lock); } /* * Drain the transmit queues and reclaim resources. */ static void ath5k_txq_cleanup(struct ath5k_softc *sc) { struct ath5k_hw *ah = sc->ah; unsigned int i; /* XXX return value */ if (likely(!test_bit(ATH_STAT_INVALID, sc->status))) { /* don't touch the hardware if marked invalid */ ath5k_hw_stop_tx_dma(ah, sc->bhalq); ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "beacon queue %x\n", ath5k_hw_get_txdp(ah, sc->bhalq)); for (i = 0; i < ARRAY_SIZE(sc->txqs); i++) if (sc->txqs[i].setup) { ath5k_hw_stop_tx_dma(ah, sc->txqs[i].qnum); ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "txq [%u] %x, " "link %p\n", sc->txqs[i].qnum, ath5k_hw_get_txdp(ah, sc->txqs[i].qnum), sc->txqs[i].link); } } for (i = 0; i < ARRAY_SIZE(sc->txqs); i++) if (sc->txqs[i].setup) ath5k_txq_drainq(sc, &sc->txqs[i]); } static void ath5k_txq_release(struct ath5k_softc *sc) { struct ath5k_txq *txq = sc->txqs; unsigned int i; for (i = 0; i < ARRAY_SIZE(sc->txqs); i++, txq++) if (txq->setup) { ath5k_hw_release_tx_queue(sc->ah, txq->qnum); txq->setup = false; } } /*************\ * RX Handling * \*************/ /* * Enable the receive h/w following a reset. */ static int ath5k_rx_start(struct ath5k_softc *sc) { struct ath5k_hw *ah = sc->ah; struct ath_common *common = ath5k_hw_common(ah); struct ath5k_buf *bf; int ret; common->rx_bufsize = roundup(IEEE80211_MAX_LEN, common->cachelsz); ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "cachelsz %u rx_bufsize %u\n", common->cachelsz, common->rx_bufsize); spin_lock_bh(&sc->rxbuflock); sc->rxlink = NULL; list_for_each_entry(bf, &sc->rxbuf, list) { ret = ath5k_rxbuf_setup(sc, bf); if (ret != 0) { spin_unlock_bh(&sc->rxbuflock); goto err; } } bf = list_first_entry(&sc->rxbuf, struct ath5k_buf, list); ath5k_hw_set_rxdp(ah, bf->daddr); spin_unlock_bh(&sc->rxbuflock); ath5k_hw_start_rx_dma(ah); /* enable recv descriptors */ ath5k_mode_setup(sc); /* set filters, etc. */ ath5k_hw_start_rx_pcu(ah); /* re-enable PCU/DMA engine */ return 0; err: return ret; } /* * Disable the receive h/w in preparation for a reset. */ static void ath5k_rx_stop(struct ath5k_softc *sc) { struct ath5k_hw *ah = sc->ah; ath5k_hw_stop_rx_pcu(ah); /* disable PCU */ ath5k_hw_set_rx_filter(ah, 0); /* clear recv filter */ ath5k_hw_stop_rx_dma(ah); /* disable DMA engine */ ath5k_debug_printrxbuffs(sc, ah); sc->rxlink = NULL; /* just in case */ } static unsigned int ath5k_rx_decrypted(struct ath5k_softc *sc, struct ath5k_desc *ds, struct sk_buff *skb, struct ath5k_rx_status *rs) { struct ath5k_hw *ah = sc->ah; struct ath_common *common = ath5k_hw_common(ah); struct ieee80211_hdr *hdr = (void *)skb->data; unsigned int keyix, hlen; if (!(rs->rs_status & AR5K_RXERR_DECRYPT) && rs->rs_keyix != AR5K_RXKEYIX_INVALID) return RX_FLAG_DECRYPTED; /* Apparently when a default key is used to decrypt the packet the hw does not set the index used to decrypt. In such cases get the index from the packet. */ hlen = ieee80211_hdrlen(hdr->frame_control); if (ieee80211_has_protected(hdr->frame_control) && !(rs->rs_status & AR5K_RXERR_DECRYPT) && skb->len >= hlen + 4) { keyix = skb->data[hlen + 3] >> 6; if (test_bit(keyix, common->keymap)) return RX_FLAG_DECRYPTED; } return 0; } static void ath5k_check_ibss_tsf(struct ath5k_softc *sc, struct sk_buff *skb, struct ieee80211_rx_status *rxs) { struct ath_common *common = ath5k_hw_common(sc->ah); u64 tsf, bc_tstamp; u32 hw_tu; struct ieee80211_mgmt *mgmt = (struct ieee80211_mgmt *)skb->data; if (ieee80211_is_beacon(mgmt->frame_control) && le16_to_cpu(mgmt->u.beacon.capab_info) & WLAN_CAPABILITY_IBSS && memcmp(mgmt->bssid, common->curbssid, ETH_ALEN) == 0) { /* * Received an IBSS beacon with the same BSSID. Hardware *must* * have updated the local TSF. We have to work around various * hardware bugs, though... */ tsf = ath5k_hw_get_tsf64(sc->ah); bc_tstamp = le64_to_cpu(mgmt->u.beacon.timestamp); hw_tu = TSF_TO_TU(tsf); ATH5K_DBG_UNLIMIT(sc, ATH5K_DEBUG_BEACON, "beacon %llx mactime %llx (diff %lld) tsf now %llx\n", (unsigned long long)bc_tstamp, (unsigned long long)rxs->mactime, (unsigned long long)(rxs->mactime - bc_tstamp), (unsigned long long)tsf); /* * Sometimes the HW will give us a wrong tstamp in the rx * status, causing the timestamp extension to go wrong. * (This seems to happen especially with beacon frames bigger * than 78 byte (incl. FCS)) * But we know that the receive timestamp must be later than the * timestamp of the beacon since HW must have synced to that. * * NOTE: here we assume mactime to be after the frame was * received, not like mac80211 which defines it at the start. */ if (bc_tstamp > rxs->mactime) { ATH5K_DBG_UNLIMIT(sc, ATH5K_DEBUG_BEACON, "fixing mactime from %llx to %llx\n", (unsigned long long)rxs->mactime, (unsigned long long)tsf); rxs->mactime = tsf; } /* * Local TSF might have moved higher than our beacon timers, * in that case we have to update them to continue sending * beacons. This also takes care of synchronizing beacon sending * times with other stations. */ if (hw_tu >= sc->nexttbtt) ath5k_beacon_update_timers(sc, bc_tstamp); } } static void ath5k_update_beacon_rssi(struct ath5k_softc *sc, struct sk_buff *skb, int rssi) { struct ieee80211_mgmt *mgmt = (struct ieee80211_mgmt *)skb->data; struct ath5k_hw *ah = sc->ah; struct ath_common *common = ath5k_hw_common(ah); /* only beacons from our BSSID */ if (!ieee80211_is_beacon(mgmt->frame_control) || memcmp(mgmt->bssid, common->curbssid, ETH_ALEN) != 0) return; ah->ah_beacon_rssi_avg = ath5k_moving_average(ah->ah_beacon_rssi_avg, rssi); /* in IBSS mode we should keep RSSI statistics per neighbour */ /* le16_to_cpu(mgmt->u.beacon.capab_info) & WLAN_CAPABILITY_IBSS */ } /* * Compute padding position. skb must contains an IEEE 802.11 frame */ static int ath5k_common_padpos(struct sk_buff *skb) { struct ieee80211_hdr * hdr = (struct ieee80211_hdr *)skb->data; __le16 frame_control = hdr->frame_control; int padpos = 24; if (ieee80211_has_a4(frame_control)) { padpos += ETH_ALEN; } if (ieee80211_is_data_qos(frame_control)) { padpos += IEEE80211_QOS_CTL_LEN; } return padpos; } /* * This function expects a 802.11 frame and returns the number of * bytes added, or -1 if we don't have enought header room. */ static int ath5k_add_padding(struct sk_buff *skb) { int padpos = ath5k_common_padpos(skb); int padsize = padpos & 3; if (padsize && skb->len>padpos) { if (skb_headroom(skb) < padsize) return -1; skb_push(skb, padsize); memmove(skb->data, skb->data+padsize, padpos); return padsize; } return 0; } /* * This function expects a 802.11 frame and returns the number of * bytes removed */ static int ath5k_remove_padding(struct sk_buff *skb) { int padpos = ath5k_common_padpos(skb); int padsize = padpos & 3; if (padsize && skb->len>=padpos+padsize) { memmove(skb->data + padsize, skb->data, padpos); skb_pull(skb, padsize); return padsize; } return 0; } static void ath5k_tasklet_rx(unsigned long data) { struct ieee80211_rx_status *rxs; struct ath5k_rx_status rs = {}; struct sk_buff *skb, *next_skb; dma_addr_t next_skb_addr; struct ath5k_softc *sc = (void *)data; struct ath5k_hw *ah = sc->ah; struct ath_common *common = ath5k_hw_common(ah); struct ath5k_buf *bf; struct ath5k_desc *ds; int ret; int rx_flag; spin_lock(&sc->rxbuflock); if (list_empty(&sc->rxbuf)) { ATH5K_WARN(sc, "empty rx buf pool\n"); goto unlock; } do { rx_flag = 0; bf = list_first_entry(&sc->rxbuf, struct ath5k_buf, list); BUG_ON(bf->skb == NULL); skb = bf->skb; ds = bf->desc; /* bail if HW is still using self-linked descriptor */ if (ath5k_hw_get_rxdp(sc->ah) == bf->daddr) break; ret = sc->ah->ah_proc_rx_desc(sc->ah, ds, &rs); if (unlikely(ret == -EINPROGRESS)) break; else if (unlikely(ret)) { ATH5K_ERR(sc, "error in processing rx descriptor\n"); sc->stats.rxerr_proc++; spin_unlock(&sc->rxbuflock); return; } sc->stats.rx_all_count++; if (unlikely(rs.rs_more)) { ATH5K_WARN(sc, "unsupported jumbo\n"); sc->stats.rxerr_jumbo++; goto next; } if (unlikely(rs.rs_status)) { if (rs.rs_status & AR5K_RXERR_CRC) sc->stats.rxerr_crc++; if (rs.rs_status & AR5K_RXERR_FIFO) sc->stats.rxerr_fifo++; if (rs.rs_status & AR5K_RXERR_PHY) { sc->stats.rxerr_phy++; if (rs.rs_phyerr > 0 && rs.rs_phyerr < 32) sc->stats.rxerr_phy_code[rs.rs_phyerr]++; goto next; } if (rs.rs_status & AR5K_RXERR_DECRYPT) { /* * Decrypt error. If the error occurred * because there was no hardware key, then * let the frame through so the upper layers * can process it. This is necessary for 5210 * parts which have no way to setup a ``clear'' * key cache entry. * * XXX do key cache faulting */ sc->stats.rxerr_decrypt++; if (rs.rs_keyix == AR5K_RXKEYIX_INVALID && !(rs.rs_status & AR5K_RXERR_CRC)) goto accept; } if (rs.rs_status & AR5K_RXERR_MIC) { rx_flag |= RX_FLAG_MMIC_ERROR; sc->stats.rxerr_mic++; goto accept; } /* let crypto-error packets fall through in MNTR */ if ((rs.rs_status & ~(AR5K_RXERR_DECRYPT|AR5K_RXERR_MIC)) || sc->opmode != NL80211_IFTYPE_MONITOR) goto next; } accept: next_skb = ath5k_rx_skb_alloc(sc, &next_skb_addr); /* * If we can't replace bf->skb with a new skb under memory * pressure, just skip this packet */ if (!next_skb) goto next; pci_unmap_single(sc->pdev, bf->skbaddr, common->rx_bufsize, PCI_DMA_FROMDEVICE); skb_put(skb, rs.rs_datalen); /* The MAC header is padded to have 32-bit boundary if the * packet payload is non-zero. The general calculation for * padsize would take into account odd header lengths: * padsize = (4 - hdrlen % 4) % 4; However, since only * even-length headers are used, padding can only be 0 or 2 * bytes and we can optimize this a bit. In addition, we must * not try to remove padding from short control frames that do * not have payload. */ ath5k_remove_padding(skb); rxs = IEEE80211_SKB_RXCB(skb); /* * always extend the mac timestamp, since this information is * also needed for proper IBSS merging. * * XXX: it might be too late to do it here, since rs_tstamp is * 15bit only. that means TSF extension has to be done within * 32768usec (about 32ms). it might be necessary to move this to * the interrupt handler, like it is done in madwifi. * * Unfortunately we don't know when the hardware takes the rx * timestamp (beginning of phy frame, data frame, end of rx?). * The only thing we know is that it is hardware specific... * On AR5213 it seems the rx timestamp is at the end of the * frame, but i'm not sure. * * NOTE: mac80211 defines mactime at the beginning of the first * data symbol. Since we don't have any time references it's * impossible to comply to that. This affects IBSS merge only * right now, so it's not too bad... */ rxs->mactime = ath5k_extend_tsf(sc->ah, rs.rs_tstamp); rxs->flag = rx_flag | RX_FLAG_TSFT; rxs->freq = sc->curchan->center_freq; rxs->band = sc->curband->band; rxs->noise = sc->ah->ah_noise_floor; rxs->signal = rxs->noise + rs.rs_rssi; rxs->antenna = rs.rs_antenna; if (rs.rs_antenna > 0 && rs.rs_antenna < 5) sc->stats.antenna_rx[rs.rs_antenna]++; else sc->stats.antenna_rx[0]++; /* invalid */ rxs->rate_idx = ath5k_hw_to_driver_rix(sc, rs.rs_rate); rxs->flag |= ath5k_rx_decrypted(sc, ds, skb, &rs); if (rxs->rate_idx >= 0 && rs.rs_rate == sc->curband->bitrates[rxs->rate_idx].hw_value_short) rxs->flag |= RX_FLAG_SHORTPRE; ath5k_debug_dump_skb(sc, skb, "RX ", 0); ath5k_update_beacon_rssi(sc, skb, rs.rs_rssi); /* check beacons in IBSS mode */ if (sc->opmode == NL80211_IFTYPE_ADHOC) ath5k_check_ibss_tsf(sc, skb, rxs); ieee80211_rx(sc->hw, skb); bf->skb = next_skb; bf->skbaddr = next_skb_addr; next: list_move_tail(&bf->list, &sc->rxbuf); } while (ath5k_rxbuf_setup(sc, bf) == 0); unlock: spin_unlock(&sc->rxbuflock); } /*************\ * TX Handling * \*************/ static void ath5k_tx_processq(struct ath5k_softc *sc, struct ath5k_txq *txq) { struct ath5k_tx_status ts = {}; struct ath5k_buf *bf, *bf0; struct ath5k_desc *ds; struct sk_buff *skb; struct ieee80211_tx_info *info; int i, ret; spin_lock(&txq->lock); list_for_each_entry_safe(bf, bf0, &txq->q, list) { ds = bf->desc; /* * It's possible that the hardware can say the buffer is * completed when it hasn't yet loaded the ds_link from * host memory and moved on. If there are more TX * descriptors in the queue, wait for TXDP to change * before processing this one. */ if (ath5k_hw_get_txdp(sc->ah, txq->qnum) == bf->daddr && !list_is_last(&bf->list, &txq->q)) break; ret = sc->ah->ah_proc_tx_desc(sc->ah, ds, &ts); if (unlikely(ret == -EINPROGRESS)) break; else if (unlikely(ret)) { ATH5K_ERR(sc, "error %d while processing queue %u\n", ret, txq->qnum); break; } sc->stats.tx_all_count++; skb = bf->skb; info = IEEE80211_SKB_CB(skb); bf->skb = NULL; pci_unmap_single(sc->pdev, bf->skbaddr, skb->len, PCI_DMA_TODEVICE); ieee80211_tx_info_clear_status(info); for (i = 0; i < 4; i++) { struct ieee80211_tx_rate *r = &info->status.rates[i]; if (ts.ts_rate[i]) { r->idx = ath5k_hw_to_driver_rix(sc, ts.ts_rate[i]); r->count = ts.ts_retry[i]; } else { r->idx = -1; r->count = 0; } } /* count the successful attempt as well */ info->status.rates[ts.ts_final_idx].count++; if (unlikely(ts.ts_status)) { sc->stats.ack_fail++; if (ts.ts_status & AR5K_TXERR_FILT) { info->flags |= IEEE80211_TX_STAT_TX_FILTERED; sc->stats.txerr_filt++; } if (ts.ts_status & AR5K_TXERR_XRETRY) sc->stats.txerr_retry++; if (ts.ts_status & AR5K_TXERR_FIFO) sc->stats.txerr_fifo++; } else { info->flags |= IEEE80211_TX_STAT_ACK; info->status.ack_signal = ts.ts_rssi; } /* * Remove MAC header padding before giving the frame * back to mac80211. */ ath5k_remove_padding(skb); if (ts.ts_antenna > 0 && ts.ts_antenna < 5) sc->stats.antenna_tx[ts.ts_antenna]++; else sc->stats.antenna_tx[0]++; /* invalid */ ieee80211_tx_status(sc->hw, skb); spin_lock(&sc->txbuflock); list_move_tail(&bf->list, &sc->txbuf); sc->txbuf_len++; spin_unlock(&sc->txbuflock); } if (likely(list_empty(&txq->q))) txq->link = NULL; spin_unlock(&txq->lock); if (sc->txbuf_len > ATH_TXBUF / 5) ieee80211_wake_queues(sc->hw); } static void ath5k_tasklet_tx(unsigned long data) { int i; struct ath5k_softc *sc = (void *)data; for (i=0; i < AR5K_NUM_TX_QUEUES; i++) if (sc->txqs[i].setup && (sc->ah->ah_txq_isr & BIT(i))) ath5k_tx_processq(sc, &sc->txqs[i]); } /*****************\ * Beacon handling * \*****************/ /* * Setup the beacon frame for transmit. */ static int ath5k_beacon_setup(struct ath5k_softc *sc, struct ath5k_buf *bf) { struct sk_buff *skb = bf->skb; struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); struct ath5k_hw *ah = sc->ah; struct ath5k_desc *ds; int ret = 0; u8 antenna; u32 flags; const int padsize = 0; bf->skbaddr = pci_map_single(sc->pdev, skb->data, skb->len, PCI_DMA_TODEVICE); ATH5K_DBG(sc, ATH5K_DEBUG_BEACON, "skb %p [data %p len %u] " "skbaddr %llx\n", skb, skb->data, skb->len, (unsigned long long)bf->skbaddr); if (pci_dma_mapping_error(sc->pdev, bf->skbaddr)) { ATH5K_ERR(sc, "beacon DMA mapping failed\n"); return -EIO; } ds = bf->desc; antenna = ah->ah_tx_ant; flags = AR5K_TXDESC_NOACK; if (sc->opmode == NL80211_IFTYPE_ADHOC && ath5k_hw_hasveol(ah)) { ds->ds_link = bf->daddr; /* self-linked */ flags |= AR5K_TXDESC_VEOL; } else ds->ds_link = 0; /* * If we use multiple antennas on AP and use * the Sectored AP scenario, switch antenna every * 4 beacons to make sure everybody hears our AP. * When a client tries to associate, hw will keep * track of the tx antenna to be used for this client * automaticaly, based on ACKed packets. * * Note: AP still listens and transmits RTS on the * default antenna which is supposed to be an omni. * * Note2: On sectored scenarios it's possible to have * multiple antennas (1omni -the default- and 14 sectors) * so if we choose to actually support this mode we need * to allow user to set how many antennas we have and tweak * the code below to send beacons on all of them. */ if (ah->ah_ant_mode == AR5K_ANTMODE_SECTOR_AP) antenna = sc->bsent & 4 ? 2 : 1; /* FIXME: If we are in g mode and rate is a CCK rate * subtract ah->ah_txpower.txp_cck_ofdm_pwr_delta * from tx power (value is in dB units already) */ ds->ds_data = bf->skbaddr; ret = ah->ah_setup_tx_desc(ah, ds, skb->len, ieee80211_get_hdrlen_from_skb(skb), padsize, AR5K_PKT_TYPE_BEACON, (sc->power_level * 2), ieee80211_get_tx_rate(sc->hw, info)->hw_value, 1, AR5K_TXKEYIX_INVALID, antenna, flags, 0, 0); if (ret) goto err_unmap; return 0; err_unmap: pci_unmap_single(sc->pdev, bf->skbaddr, skb->len, PCI_DMA_TODEVICE); return ret; } /* * Transmit a beacon frame at SWBA. Dynamic updates to the * frame contents are done as needed and the slot time is * also adjusted based on current state. * * This is called from software irq context (beacontq or restq * tasklets) or user context from ath5k_beacon_config. */ static void ath5k_beacon_send(struct ath5k_softc *sc) { struct ath5k_buf *bf = sc->bbuf; struct ath5k_hw *ah = sc->ah; struct sk_buff *skb; ATH5K_DBG_UNLIMIT(sc, ATH5K_DEBUG_BEACON, "in beacon_send\n"); if (unlikely(bf->skb == NULL || sc->opmode == NL80211_IFTYPE_STATION || sc->opmode == NL80211_IFTYPE_MONITOR)) { ATH5K_WARN(sc, "bf=%p bf_skb=%p\n", bf, bf ? bf->skb : NULL); return; } /* * Check if the previous beacon has gone out. If * not don't don't try to post another, skip this * period and wait for the next. Missed beacons * indicate a problem and should not occur. If we * miss too many consecutive beacons reset the device. */ if (unlikely(ath5k_hw_num_tx_pending(ah, sc->bhalq) != 0)) { sc->bmisscount++; ATH5K_DBG(sc, ATH5K_DEBUG_BEACON, "missed %u consecutive beacons\n", sc->bmisscount); if (sc->bmisscount > 10) { /* NB: 10 is a guess */ ATH5K_DBG(sc, ATH5K_DEBUG_BEACON, "stuck beacon time (%u missed)\n", sc->bmisscount); tasklet_schedule(&sc->restq); } return; } if (unlikely(sc->bmisscount != 0)) { ATH5K_DBG(sc, ATH5K_DEBUG_BEACON, "resume beacon xmit after %u misses\n", sc->bmisscount); sc->bmisscount = 0; } /* * Stop any current dma and put the new frame on the queue. * This should never fail since we check above that no frames * are still pending on the queue. */ if (unlikely(ath5k_hw_stop_tx_dma(ah, sc->bhalq))) { ATH5K_WARN(sc, "beacon queue %u didn't start/stop ?\n", sc->bhalq); /* NB: hw still stops DMA, so proceed */ } /* refresh the beacon for AP mode */ if (sc->opmode == NL80211_IFTYPE_AP) ath5k_beacon_update(sc->hw, sc->vif); ath5k_hw_set_txdp(ah, sc->bhalq, bf->daddr); ath5k_hw_start_tx_dma(ah, sc->bhalq); ATH5K_DBG(sc, ATH5K_DEBUG_BEACON, "TXDP[%u] = %llx (%p)\n", sc->bhalq, (unsigned long long)bf->daddr, bf->desc); skb = ieee80211_get_buffered_bc(sc->hw, sc->vif); while (skb) { ath5k_tx_queue(sc->hw, skb, sc->cabq); skb = ieee80211_get_buffered_bc(sc->hw, sc->vif); } sc->bsent++; } /** * ath5k_beacon_update_timers - update beacon timers * * @sc: struct ath5k_softc pointer we are operating on * @bc_tsf: the timestamp of the beacon. 0 to reset the TSF. -1 to perform a * beacon timer update based on the current HW TSF. * * Calculate the next target beacon transmit time (TBTT) based on the timestamp * of a received beacon or the current local hardware TSF and write it to the * beacon timer registers. * * This is called in a variety of situations, e.g. when a beacon is received, * when a TSF update has been detected, but also when an new IBSS is created or * when we otherwise know we have to update the timers, but we keep it in this * function to have it all together in one place. */ static void ath5k_beacon_update_timers(struct ath5k_softc *sc, u64 bc_tsf) { struct ath5k_hw *ah = sc->ah; u32 nexttbtt, intval, hw_tu, bc_tu; u64 hw_tsf; intval = sc->bintval & AR5K_BEACON_PERIOD; if (WARN_ON(!intval)) return; /* beacon TSF converted to TU */ bc_tu = TSF_TO_TU(bc_tsf); /* current TSF converted to TU */ hw_tsf = ath5k_hw_get_tsf64(ah); hw_tu = TSF_TO_TU(hw_tsf); #define FUDGE 3 /* we use FUDGE to make sure the next TBTT is ahead of the current TU */ if (bc_tsf == -1) { /* * no beacons received, called internally. * just need to refresh timers based on HW TSF. */ nexttbtt = roundup(hw_tu + FUDGE, intval); } else if (bc_tsf == 0) { /* * no beacon received, probably called by ath5k_reset_tsf(). * reset TSF to start with 0. */ nexttbtt = intval; intval |= AR5K_BEACON_RESET_TSF; } else if (bc_tsf > hw_tsf) { /* * beacon received, SW merge happend but HW TSF not yet updated. * not possible to reconfigure timers yet, but next time we * receive a beacon with the same BSSID, the hardware will * automatically update the TSF and then we need to reconfigure * the timers. */ ATH5K_DBG_UNLIMIT(sc, ATH5K_DEBUG_BEACON, "need to wait for HW TSF sync\n"); return; } else { /* * most important case for beacon synchronization between STA. * * beacon received and HW TSF has been already updated by HW. * update next TBTT based on the TSF of the beacon, but make * sure it is ahead of our local TSF timer. */ nexttbtt = bc_tu + roundup(hw_tu + FUDGE - bc_tu, intval); } #undef FUDGE sc->nexttbtt = nexttbtt; intval |= AR5K_BEACON_ENA; ath5k_hw_init_beacon(ah, nexttbtt, intval); /* * debugging output last in order to preserve the time critical aspect * of this function */ if (bc_tsf == -1) ATH5K_DBG_UNLIMIT(sc, ATH5K_DEBUG_BEACON, "reconfigured timers based on HW TSF\n"); else if (bc_tsf == 0) ATH5K_DBG_UNLIMIT(sc, ATH5K_DEBUG_BEACON, "reset HW TSF and timers\n"); else ATH5K_DBG_UNLIMIT(sc, ATH5K_DEBUG_BEACON, "updated timers based on beacon TSF\n"); ATH5K_DBG_UNLIMIT(sc, ATH5K_DEBUG_BEACON, "bc_tsf %llx hw_tsf %llx bc_tu %u hw_tu %u nexttbtt %u\n", (unsigned long long) bc_tsf, (unsigned long long) hw_tsf, bc_tu, hw_tu, nexttbtt); ATH5K_DBG_UNLIMIT(sc, ATH5K_DEBUG_BEACON, "intval %u %s %s\n", intval & AR5K_BEACON_PERIOD, intval & AR5K_BEACON_ENA ? "AR5K_BEACON_ENA" : "", intval & AR5K_BEACON_RESET_TSF ? "AR5K_BEACON_RESET_TSF" : ""); } /** * ath5k_beacon_config - Configure the beacon queues and interrupts * * @sc: struct ath5k_softc pointer we are operating on * * In IBSS mode we use a self-linked tx descriptor if possible. We enable SWBA * interrupts to detect TSF updates only. */ static void ath5k_beacon_config(struct ath5k_softc *sc) { struct ath5k_hw *ah = sc->ah; unsigned long flags; spin_lock_irqsave(&sc->block, flags); sc->bmisscount = 0; sc->imask &= ~(AR5K_INT_BMISS | AR5K_INT_SWBA); if (sc->enable_beacon) { /* * In IBSS mode we use a self-linked tx descriptor and let the * hardware send the beacons automatically. We have to load it * only once here. * We use the SWBA interrupt only to keep track of the beacon * timers in order to detect automatic TSF updates. */ ath5k_beaconq_config(sc); sc->imask |= AR5K_INT_SWBA; if (sc->opmode == NL80211_IFTYPE_ADHOC) { if (ath5k_hw_hasveol(ah)) ath5k_beacon_send(sc); } else ath5k_beacon_update_timers(sc, -1); } else { ath5k_hw_stop_tx_dma(sc->ah, sc->bhalq); } ath5k_hw_set_imr(ah, sc->imask); mmiowb(); spin_unlock_irqrestore(&sc->block, flags); } static void ath5k_tasklet_beacon(unsigned long data) { struct ath5k_softc *sc = (struct ath5k_softc *) data; /* * Software beacon alert--time to send a beacon. * * In IBSS mode we use this interrupt just to * keep track of the next TBTT (target beacon * transmission time) in order to detect wether * automatic TSF updates happened. */ if (sc->opmode == NL80211_IFTYPE_ADHOC) { /* XXX: only if VEOL suppported */ u64 tsf = ath5k_hw_get_tsf64(sc->ah); sc->nexttbtt += sc->bintval; ATH5K_DBG(sc, ATH5K_DEBUG_BEACON, "SWBA nexttbtt: %x hw_tu: %x " "TSF: %llx\n", sc->nexttbtt, TSF_TO_TU(tsf), (unsigned long long) tsf); } else { spin_lock(&sc->block); ath5k_beacon_send(sc); spin_unlock(&sc->block); } } /********************\ * Interrupt handling * \********************/ static int ath5k_init(struct ath5k_softc *sc) { struct ath5k_hw *ah = sc->ah; int ret, i; mutex_lock(&sc->lock); ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "mode %d\n", sc->opmode); /* * Stop anything previously setup. This is safe * no matter this is the first time through or not. */ ath5k_stop_locked(sc); /* * The basic interface to setting the hardware in a good * state is ``reset''. On return the hardware is known to * be powered up and with interrupts disabled. This must * be followed by initialization of the appropriate bits * and then setup of the interrupt mask. */ sc->curchan = sc->hw->conf.channel; sc->curband = &sc->sbands[sc->curchan->band]; sc->imask = AR5K_INT_RXOK | AR5K_INT_RXERR | AR5K_INT_RXEOL | AR5K_INT_RXORN | AR5K_INT_TXDESC | AR5K_INT_TXEOL | AR5K_INT_FATAL | AR5K_INT_GLOBAL | AR5K_INT_MIB; ret = ath5k_reset(sc, NULL); if (ret) goto done; ath5k_rfkill_hw_start(ah); /* * Reset the key cache since some parts do not reset the * contents on initial power up or resume from suspend. */ for (i = 0; i < AR5K_KEYTABLE_SIZE; i++) ath5k_hw_reset_key(ah, i); ath5k_hw_set_ack_bitrate_high(ah, true); ret = 0; done: mmiowb(); mutex_unlock(&sc->lock); return ret; } static int ath5k_stop_locked(struct ath5k_softc *sc) { struct ath5k_hw *ah = sc->ah; ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "invalid %u\n", test_bit(ATH_STAT_INVALID, sc->status)); /* * Shutdown the hardware and driver: * stop output from above * disable interrupts * turn off timers * turn off the radio * clear transmit machinery * clear receive machinery * drain and release tx queues * reclaim beacon resources * power down hardware * * Note that some of this work is not possible if the * hardware is gone (invalid). */ ieee80211_stop_queues(sc->hw); if (!test_bit(ATH_STAT_INVALID, sc->status)) { ath5k_led_off(sc); ath5k_hw_set_imr(ah, 0); synchronize_irq(sc->pdev->irq); } ath5k_txq_cleanup(sc); if (!test_bit(ATH_STAT_INVALID, sc->status)) { ath5k_rx_stop(sc); ath5k_hw_phy_disable(ah); } else sc->rxlink = NULL; return 0; } /* * Stop the device, grabbing the top-level lock to protect * against concurrent entry through ath5k_init (which can happen * if another thread does a system call and the thread doing the * stop is preempted). */ static int ath5k_stop_hw(struct ath5k_softc *sc) { int ret; mutex_lock(&sc->lock); ret = ath5k_stop_locked(sc); if (ret == 0 && !test_bit(ATH_STAT_INVALID, sc->status)) { /* * Don't set the card in full sleep mode! * * a) When the device is in this state it must be carefully * woken up or references to registers in the PCI clock * domain may freeze the bus (and system). This varies * by chip and is mostly an issue with newer parts * (madwifi sources mentioned srev >= 0x78) that go to * sleep more quickly. * * b) On older chips full sleep results a weird behaviour * during wakeup. I tested various cards with srev < 0x78 * and they don't wake up after module reload, a second * module reload is needed to bring the card up again. * * Until we figure out what's going on don't enable * full chip reset on any chip (this is what Legacy HAL * and Sam's HAL do anyway). Instead Perform a full reset * on the device (same as initial state after attach) and * leave it idle (keep MAC/BB on warm reset) */ ret = ath5k_hw_on_hold(sc->ah); ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "putting device to sleep\n"); } ath5k_txbuf_free(sc, sc->bbuf); mmiowb(); mutex_unlock(&sc->lock); tasklet_kill(&sc->rxtq); tasklet_kill(&sc->txtq); tasklet_kill(&sc->restq); tasklet_kill(&sc->calib); tasklet_kill(&sc->beacontq); tasklet_kill(&sc->ani_tasklet); ath5k_rfkill_hw_stop(sc->ah); return ret; } static void ath5k_intr_calibration_poll(struct ath5k_hw *ah) { if (time_is_before_eq_jiffies(ah->ah_cal_next_ani) && !(ah->ah_cal_mask & AR5K_CALIBRATION_FULL)) { /* run ANI only when full calibration is not active */ ah->ah_cal_next_ani = jiffies + msecs_to_jiffies(ATH5K_TUNE_CALIBRATION_INTERVAL_ANI); tasklet_schedule(&ah->ah_sc->ani_tasklet); } else if (time_is_before_eq_jiffies(ah->ah_cal_next_full)) { ah->ah_cal_next_full = jiffies + msecs_to_jiffies(ATH5K_TUNE_CALIBRATION_INTERVAL_FULL); tasklet_schedule(&ah->ah_sc->calib); } /* we could use SWI to generate enough interrupts to meet our * calibration interval requirements, if necessary: * AR5K_REG_ENABLE_BITS(ah, AR5K_CR, AR5K_CR_SWI); */ } static irqreturn_t ath5k_intr(int irq, void *dev_id) { struct ath5k_softc *sc = dev_id; struct ath5k_hw *ah = sc->ah; enum ath5k_int status; unsigned int counter = 1000; if (unlikely(test_bit(ATH_STAT_INVALID, sc->status) || !ath5k_hw_is_intr_pending(ah))) return IRQ_NONE; do { ath5k_hw_get_isr(ah, &status); /* NB: clears IRQ too */ ATH5K_DBG(sc, ATH5K_DEBUG_INTR, "status 0x%x/0x%x\n", status, sc->imask); if (unlikely(status & AR5K_INT_FATAL)) { /* * Fatal errors are unrecoverable. * Typically these are caused by DMA errors. */ tasklet_schedule(&sc->restq); } else if (unlikely(status & AR5K_INT_RXORN)) { /* * Receive buffers are full. Either the bus is busy or * the CPU is not fast enough to process all received * frames. * Older chipsets need a reset to come out of this * condition, but we treat it as RX for newer chips. * We don't know exactly which versions need a reset - * this guess is copied from the HAL. */ sc->stats.rxorn_intr++; if (ah->ah_mac_srev < AR5K_SREV_AR5212) tasklet_schedule(&sc->restq); else tasklet_schedule(&sc->rxtq); } else { if (status & AR5K_INT_SWBA) { tasklet_hi_schedule(&sc->beacontq); } if (status & AR5K_INT_RXEOL) { /* * NB: the hardware should re-read the link when * RXE bit is written, but it doesn't work at * least on older hardware revs. */ sc->rxlink = NULL; } if (status & AR5K_INT_TXURN) { /* bump tx trigger level */ ath5k_hw_update_tx_triglevel(ah, true); } if (status & (AR5K_INT_RXOK | AR5K_INT_RXERR)) tasklet_schedule(&sc->rxtq); if (status & (AR5K_INT_TXOK | AR5K_INT_TXDESC | AR5K_INT_TXERR | AR5K_INT_TXEOL)) tasklet_schedule(&sc->txtq); if (status & AR5K_INT_BMISS) { /* TODO */ } if (status & AR5K_INT_MIB) { sc->stats.mib_intr++; ath5k_hw_update_mib_counters(ah); ath5k_ani_mib_intr(ah); } if (status & AR5K_INT_GPIO) tasklet_schedule(&sc->rf_kill.toggleq); } } while (ath5k_hw_is_intr_pending(ah) && --counter > 0); if (unlikely(!counter)) ATH5K_WARN(sc, "too many interrupts, giving up for now\n"); ath5k_intr_calibration_poll(ah); return IRQ_HANDLED; } static void ath5k_tasklet_reset(unsigned long data) { struct ath5k_softc *sc = (void *)data; ath5k_reset_wake(sc); } /* * Periodically recalibrate the PHY to account * for temperature/environment changes. */ static void ath5k_tasklet_calibrate(unsigned long data) { struct ath5k_softc *sc = (void *)data; struct ath5k_hw *ah = sc->ah; /* Only full calibration for now */ ah->ah_cal_mask |= AR5K_CALIBRATION_FULL; /* Stop queues so that calibration * doesn't interfere with tx */ ieee80211_stop_queues(sc->hw); ATH5K_DBG(sc, ATH5K_DEBUG_CALIBRATE, "channel %u/%x\n", ieee80211_frequency_to_channel(sc->curchan->center_freq), sc->curchan->hw_value); if (ath5k_hw_gainf_calibrate(ah) == AR5K_RFGAIN_NEED_CHANGE) { /* * Rfgain is out of bounds, reset the chip * to load new gain values. */ ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "calibration, resetting\n"); ath5k_reset(sc, sc->curchan); } if (ath5k_hw_phy_calibrate(ah, sc->curchan)) ATH5K_ERR(sc, "calibration of channel %u failed\n", ieee80211_frequency_to_channel( sc->curchan->center_freq)); /* Wake queues */ ieee80211_wake_queues(sc->hw); ah->ah_cal_mask &= ~AR5K_CALIBRATION_FULL; } static void ath5k_tasklet_ani(unsigned long data) { struct ath5k_softc *sc = (void *)data; struct ath5k_hw *ah = sc->ah; ah->ah_cal_mask |= AR5K_CALIBRATION_ANI; ath5k_ani_calibration(ah); ah->ah_cal_mask &= ~AR5K_CALIBRATION_ANI; } /********************\ * Mac80211 functions * \********************/ static int ath5k_tx(struct ieee80211_hw *hw, struct sk_buff *skb) { struct ath5k_softc *sc = hw->priv; return ath5k_tx_queue(hw, skb, sc->txq); } static int ath5k_tx_queue(struct ieee80211_hw *hw, struct sk_buff *skb, struct ath5k_txq *txq) { struct ath5k_softc *sc = hw->priv; struct ath5k_buf *bf; unsigned long flags; int padsize; ath5k_debug_dump_skb(sc, skb, "TX ", 1); if (sc->opmode == NL80211_IFTYPE_MONITOR) ATH5K_DBG(sc, ATH5K_DEBUG_XMIT, "tx in monitor (scan?)\n"); /* * the hardware expects the header padded to 4 byte boundaries * if this is not the case we add the padding after the header */ padsize = ath5k_add_padding(skb); if (padsize < 0) { ATH5K_ERR(sc, "tx hdrlen not %%4: not enough" " headroom to pad"); goto drop_packet; } spin_lock_irqsave(&sc->txbuflock, flags); if (list_empty(&sc->txbuf)) { ATH5K_ERR(sc, "no further txbuf available, dropping packet\n"); spin_unlock_irqrestore(&sc->txbuflock, flags); ieee80211_stop_queue(hw, skb_get_queue_mapping(skb)); goto drop_packet; } bf = list_first_entry(&sc->txbuf, struct ath5k_buf, list); list_del(&bf->list); sc->txbuf_len--; if (list_empty(&sc->txbuf)) ieee80211_stop_queues(hw); spin_unlock_irqrestore(&sc->txbuflock, flags); bf->skb = skb; if (ath5k_txbuf_setup(sc, bf, txq, padsize)) { bf->skb = NULL; spin_lock_irqsave(&sc->txbuflock, flags); list_add_tail(&bf->list, &sc->txbuf); sc->txbuf_len++; spin_unlock_irqrestore(&sc->txbuflock, flags); goto drop_packet; } return NETDEV_TX_OK; drop_packet: dev_kfree_skb_any(skb); return NETDEV_TX_OK; } /* * Reset the hardware. If chan is not NULL, then also pause rx/tx * and change to the given channel. */ static int ath5k_reset(struct ath5k_softc *sc, struct ieee80211_channel *chan) { struct ath5k_hw *ah = sc->ah; int ret; ATH5K_DBG(sc, ATH5K_DEBUG_RESET, "resetting\n"); if (chan) { ath5k_hw_set_imr(ah, 0); ath5k_txq_cleanup(sc); ath5k_rx_stop(sc); sc->curchan = chan; sc->curband = &sc->sbands[chan->band]; } ret = ath5k_hw_reset(ah, sc->opmode, sc->curchan, chan != NULL); if (ret) { ATH5K_ERR(sc, "can't reset hardware (%d)\n", ret); goto err; } ret = ath5k_rx_start(sc); if (ret) { ATH5K_ERR(sc, "can't start recv logic\n"); goto err; } ath5k_ani_init(ah, ah->ah_sc->ani_state.ani_mode); /* * Change channels and update the h/w rate map if we're switching; * e.g. 11a to 11b/g. * * We may be doing a reset in response to an ioctl that changes the * channel so update any state that might change as a result. * * XXX needed? */ /* ath5k_chan_change(sc, c); */ ath5k_beacon_config(sc); /* intrs are enabled by ath5k_beacon_config */ return 0; err: return ret; } static int ath5k_reset_wake(struct ath5k_softc *sc) { int ret; ret = ath5k_reset(sc, sc->curchan); if (!ret) ieee80211_wake_queues(sc->hw); return ret; } static int ath5k_start(struct ieee80211_hw *hw) { return ath5k_init(hw->priv); } static void ath5k_stop(struct ieee80211_hw *hw) { ath5k_stop_hw(hw->priv); } static int ath5k_add_interface(struct ieee80211_hw *hw, struct ieee80211_vif *vif) { struct ath5k_softc *sc = hw->priv; int ret; mutex_lock(&sc->lock); if (sc->vif) { ret = 0; goto end; } sc->vif = vif; switch (vif->type) { case NL80211_IFTYPE_AP: case NL80211_IFTYPE_STATION: case NL80211_IFTYPE_ADHOC: case NL80211_IFTYPE_MESH_POINT: case NL80211_IFTYPE_MONITOR: sc->opmode = vif->type; break; default: ret = -EOPNOTSUPP; goto end; } ATH5K_DBG(sc, ATH5K_DEBUG_MODE, "add interface mode %d\n", sc->opmode); ath5k_hw_set_lladdr(sc->ah, vif->addr); ath5k_mode_setup(sc); ret = 0; end: mutex_unlock(&sc->lock); return ret; } static void ath5k_remove_interface(struct ieee80211_hw *hw, struct ieee80211_vif *vif) { struct ath5k_softc *sc = hw->priv; u8 mac[ETH_ALEN] = {}; mutex_lock(&sc->lock); if (sc->vif != vif) goto end; ath5k_hw_set_lladdr(sc->ah, mac); sc->vif = NULL; end: mutex_unlock(&sc->lock); } /* * TODO: Phy disable/diversity etc */ static int ath5k_config(struct ieee80211_hw *hw, u32 changed) { struct ath5k_softc *sc = hw->priv; struct ath5k_hw *ah = sc->ah; struct ieee80211_conf *conf = &hw->conf; int ret = 0; mutex_lock(&sc->lock); if (changed & IEEE80211_CONF_CHANGE_CHANNEL) { ret = ath5k_chan_set(sc, conf->channel); if (ret < 0) goto unlock; } if ((changed & IEEE80211_CONF_CHANGE_POWER) && (sc->power_level != conf->power_level)) { sc->power_level = conf->power_level; /* Half dB steps */ ath5k_hw_set_txpower_limit(ah, (conf->power_level * 2)); } /* TODO: * 1) Move this on config_interface and handle each case * separately eg. when we have only one STA vif, use * AR5K_ANTMODE_SINGLE_AP * * 2) Allow the user to change antenna mode eg. when only * one antenna is present * * 3) Allow the user to set default/tx antenna when possible * * 4) Default mode should handle 90% of the cases, together * with fixed a/b and single AP modes we should be able to * handle 99%. Sectored modes are extreme cases and i still * haven't found a usage for them. If we decide to support them, * then we must allow the user to set how many tx antennas we * have available */ ath5k_hw_set_antenna_mode(ah, ah->ah_ant_mode); unlock: mutex_unlock(&sc->lock); return ret; } static u64 ath5k_prepare_multicast(struct ieee80211_hw *hw, struct netdev_hw_addr_list *mc_list) { u32 mfilt[2], val; u8 pos; struct netdev_hw_addr *ha; mfilt[0] = 0; mfilt[1] = 1; netdev_hw_addr_list_for_each(ha, mc_list) { /* calculate XOR of eight 6-bit values */ val = get_unaligned_le32(ha->addr + 0); pos = (val >> 18) ^ (val >> 12) ^ (val >> 6) ^ val; val = get_unaligned_le32(ha->addr + 3); pos ^= (val >> 18) ^ (val >> 12) ^ (val >> 6) ^ val; pos &= 0x3f; mfilt[pos / 32] |= (1 << (pos % 32)); /* XXX: we might be able to just do this instead, * but not sure, needs testing, if we do use this we'd * neet to inform below to not reset the mcast */ /* ath5k_hw_set_mcast_filterindex(ah, * ha->addr[5]); */ } return ((u64)(mfilt[1]) << 32) | mfilt[0]; } #define SUPPORTED_FIF_FLAGS \ FIF_PROMISC_IN_BSS | FIF_ALLMULTI | FIF_FCSFAIL | \ FIF_PLCPFAIL | FIF_CONTROL | FIF_OTHER_BSS | \ FIF_BCN_PRBRESP_PROMISC /* * o always accept unicast, broadcast, and multicast traffic * o multicast traffic for all BSSIDs will be enabled if mac80211 * says it should be * o maintain current state of phy ofdm or phy cck error reception. * If the hardware detects any of these type of errors then * ath5k_hw_get_rx_filter() will pass to us the respective * hardware filters to be able to receive these type of frames. * o probe request frames are accepted only when operating in * hostap, adhoc, or monitor modes * o enable promiscuous mode according to the interface state * o accept beacons: * - when operating in adhoc mode so the 802.11 layer creates * node table entries for peers, * - when operating in station mode for collecting rssi data when * the station is otherwise quiet, or * - when scanning */ static void ath5k_configure_filter(struct ieee80211_hw *hw, unsigned int changed_flags, unsigned int *new_flags, u64 multicast) { struct ath5k_softc *sc = hw->priv; struct ath5k_hw *ah = sc->ah; u32 mfilt[2], rfilt; mutex_lock(&sc->lock); mfilt[0] = multicast; mfilt[1] = multicast >> 32; /* Only deal with supported flags */ changed_flags &= SUPPORTED_FIF_FLAGS; *new_flags &= SUPPORTED_FIF_FLAGS; /* If HW detects any phy or radar errors, leave those filters on. * Also, always enable Unicast, Broadcasts and Multicast * XXX: move unicast, bssid broadcasts and multicast to mac80211 */ rfilt = (ath5k_hw_get_rx_filter(ah) & (AR5K_RX_FILTER_PHYERR)) | (AR5K_RX_FILTER_UCAST | AR5K_RX_FILTER_BCAST | AR5K_RX_FILTER_MCAST); if (changed_flags & (FIF_PROMISC_IN_BSS | FIF_OTHER_BSS)) { if (*new_flags & FIF_PROMISC_IN_BSS) { rfilt |= AR5K_RX_FILTER_PROM; __set_bit(ATH_STAT_PROMISC, sc->status); } else { __clear_bit(ATH_STAT_PROMISC, sc->status); } } /* Note, AR5K_RX_FILTER_MCAST is already enabled */ if (*new_flags & FIF_ALLMULTI) { mfilt[0] = ~0; mfilt[1] = ~0; } /* This is the best we can do */ if (*new_flags & (FIF_FCSFAIL | FIF_PLCPFAIL)) rfilt |= AR5K_RX_FILTER_PHYERR; /* FIF_BCN_PRBRESP_PROMISC really means to enable beacons * and probes for any BSSID, this needs testing */ if (*new_flags & FIF_BCN_PRBRESP_PROMISC) rfilt |= AR5K_RX_FILTER_BEACON | AR5K_RX_FILTER_PROBEREQ; /* FIF_CONTROL doc says that if FIF_PROMISC_IN_BSS is not * set we should only pass on control frames for this * station. This needs testing. I believe right now this * enables *all* control frames, which is OK.. but * but we should see if we can improve on granularity */ if (*new_flags & FIF_CONTROL) rfilt |= AR5K_RX_FILTER_CONTROL; /* Additional settings per mode -- this is per ath5k */ /* XXX move these to mac80211, and add a beacon IFF flag to mac80211 */ switch (sc->opmode) { case NL80211_IFTYPE_MESH_POINT: case NL80211_IFTYPE_MONITOR: rfilt |= AR5K_RX_FILTER_CONTROL | AR5K_RX_FILTER_BEACON | AR5K_RX_FILTER_PROBEREQ | AR5K_RX_FILTER_PROM; break; case NL80211_IFTYPE_AP: case NL80211_IFTYPE_ADHOC: rfilt |= AR5K_RX_FILTER_PROBEREQ | AR5K_RX_FILTER_BEACON; break; case NL80211_IFTYPE_STATION: if (sc->assoc) rfilt |= AR5K_RX_FILTER_BEACON; default: break; } /* Set filters */ ath5k_hw_set_rx_filter(ah, rfilt); /* Set multicast bits */ ath5k_hw_set_mcast_filter(ah, mfilt[0], mfilt[1]); /* Set the cached hw filter flags, this will alter actually * be set in HW */ sc->filter_flags = rfilt; mutex_unlock(&sc->lock); } static int ath5k_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd, struct ieee80211_vif *vif, struct ieee80211_sta *sta, struct ieee80211_key_conf *key) { struct ath5k_softc *sc = hw->priv; struct ath5k_hw *ah = sc->ah; struct ath_common *common = ath5k_hw_common(ah); int ret = 0; if (modparam_nohwcrypt) return -EOPNOTSUPP; if (sc->opmode == NL80211_IFTYPE_AP) return -EOPNOTSUPP; switch (key->alg) { case ALG_WEP: case ALG_TKIP: break; case ALG_CCMP: if (sc->ah->ah_aes_support) break; return -EOPNOTSUPP; default: WARN_ON(1); return -EINVAL; } mutex_lock(&sc->lock); switch (cmd) { case SET_KEY: ret = ath5k_hw_set_key(sc->ah, key->keyidx, key, sta ? sta->addr : NULL); if (ret) { ATH5K_ERR(sc, "can't set the key\n"); goto unlock; } __set_bit(key->keyidx, common->keymap); key->hw_key_idx = key->keyidx; key->flags |= (IEEE80211_KEY_FLAG_GENERATE_IV | IEEE80211_KEY_FLAG_GENERATE_MMIC); break; case DISABLE_KEY: ath5k_hw_reset_key(sc->ah, key->keyidx); __clear_bit(key->keyidx, common->keymap); break; default: ret = -EINVAL; goto unlock; } unlock: mmiowb(); mutex_unlock(&sc->lock); return ret; } static int ath5k_get_stats(struct ieee80211_hw *hw, struct ieee80211_low_level_stats *stats) { struct ath5k_softc *sc = hw->priv; /* Force update */ ath5k_hw_update_mib_counters(sc->ah); stats->dot11ACKFailureCount = sc->stats.ack_fail; stats->dot11RTSFailureCount = sc->stats.rts_fail; stats->dot11RTSSuccessCount = sc->stats.rts_ok; stats->dot11FCSErrorCount = sc->stats.fcs_error; return 0; } static int ath5k_get_survey(struct ieee80211_hw *hw, int idx, struct survey_info *survey) { struct ath5k_softc *sc = hw->priv; struct ieee80211_conf *conf = &hw->conf; if (idx != 0) return -ENOENT; survey->channel = conf->channel; survey->filled = SURVEY_INFO_NOISE_DBM; survey->noise = sc->ah->ah_noise_floor; return 0; } static u64 ath5k_get_tsf(struct ieee80211_hw *hw) { struct ath5k_softc *sc = hw->priv; return ath5k_hw_get_tsf64(sc->ah); } static void ath5k_set_tsf(struct ieee80211_hw *hw, u64 tsf) { struct ath5k_softc *sc = hw->priv; ath5k_hw_set_tsf64(sc->ah, tsf); } static void ath5k_reset_tsf(struct ieee80211_hw *hw) { struct ath5k_softc *sc = hw->priv; /* * in IBSS mode we need to update the beacon timers too. * this will also reset the TSF if we call it with 0 */ if (sc->opmode == NL80211_IFTYPE_ADHOC) ath5k_beacon_update_timers(sc, 0); else ath5k_hw_reset_tsf(sc->ah); } /* * Updates the beacon that is sent by ath5k_beacon_send. For adhoc, * this is called only once at config_bss time, for AP we do it every * SWBA interrupt so that the TIM will reflect buffered frames. * * Called with the beacon lock. */ static int ath5k_beacon_update(struct ieee80211_hw *hw, struct ieee80211_vif *vif) { int ret; struct ath5k_softc *sc = hw->priv; struct sk_buff *skb; if (WARN_ON(!vif)) { ret = -EINVAL; goto out; } skb = ieee80211_beacon_get(hw, vif); if (!skb) { ret = -ENOMEM; goto out; } ath5k_debug_dump_skb(sc, skb, "BC ", 1); ath5k_txbuf_free(sc, sc->bbuf); sc->bbuf->skb = skb; ret = ath5k_beacon_setup(sc, sc->bbuf); if (ret) sc->bbuf->skb = NULL; out: return ret; } static void set_beacon_filter(struct ieee80211_hw *hw, bool enable) { struct ath5k_softc *sc = hw->priv; struct ath5k_hw *ah = sc->ah; u32 rfilt; rfilt = ath5k_hw_get_rx_filter(ah); if (enable) rfilt |= AR5K_RX_FILTER_BEACON; else rfilt &= ~AR5K_RX_FILTER_BEACON; ath5k_hw_set_rx_filter(ah, rfilt); sc->filter_flags = rfilt; } static void ath5k_bss_info_changed(struct ieee80211_hw *hw, struct ieee80211_vif *vif, struct ieee80211_bss_conf *bss_conf, u32 changes) { struct ath5k_softc *sc = hw->priv; struct ath5k_hw *ah = sc->ah; struct ath_common *common = ath5k_hw_common(ah); unsigned long flags; mutex_lock(&sc->lock); if (WARN_ON(sc->vif != vif)) goto unlock; if (changes & BSS_CHANGED_BSSID) { /* Cache for later use during resets */ memcpy(common->curbssid, bss_conf->bssid, ETH_ALEN); common->curaid = 0; ath5k_hw_set_associd(ah); mmiowb(); } if (changes & BSS_CHANGED_BEACON_INT) sc->bintval = bss_conf->beacon_int; if (changes & BSS_CHANGED_ASSOC) { sc->assoc = bss_conf->assoc; if (sc->opmode == NL80211_IFTYPE_STATION) set_beacon_filter(hw, sc->assoc); ath5k_hw_set_ledstate(sc->ah, sc->assoc ? AR5K_LED_ASSOC : AR5K_LED_INIT); if (bss_conf->assoc) { ATH5K_DBG(sc, ATH5K_DEBUG_ANY, "Bss Info ASSOC %d, bssid: %pM\n", bss_conf->aid, common->curbssid); common->curaid = bss_conf->aid; ath5k_hw_set_associd(ah); /* Once ANI is available you would start it here */ } } if (changes & BSS_CHANGED_BEACON) { spin_lock_irqsave(&sc->block, flags); ath5k_beacon_update(hw, vif); spin_unlock_irqrestore(&sc->block, flags); } if (changes & BSS_CHANGED_BEACON_ENABLED) sc->enable_beacon = bss_conf->enable_beacon; if (changes & (BSS_CHANGED_BEACON | BSS_CHANGED_BEACON_ENABLED | BSS_CHANGED_BEACON_INT)) ath5k_beacon_config(sc); unlock: mutex_unlock(&sc->lock); } static void ath5k_sw_scan_start(struct ieee80211_hw *hw) { struct ath5k_softc *sc = hw->priv; if (!sc->assoc) ath5k_hw_set_ledstate(sc->ah, AR5K_LED_SCAN); } static void ath5k_sw_scan_complete(struct ieee80211_hw *hw) { struct ath5k_softc *sc = hw->priv; ath5k_hw_set_ledstate(sc->ah, sc->assoc ? AR5K_LED_ASSOC : AR5K_LED_INIT); } /** * ath5k_set_coverage_class - Set IEEE 802.11 coverage class * * @hw: struct ieee80211_hw pointer * @coverage_class: IEEE 802.11 coverage class number * * Mac80211 callback. Sets slot time, ACK timeout and CTS timeout for given * coverage class. The values are persistent, they are restored after device * reset. */ static void ath5k_set_coverage_class(struct ieee80211_hw *hw, u8 coverage_class) { struct ath5k_softc *sc = hw->priv; mutex_lock(&sc->lock); ath5k_hw_set_coverage_class(sc->ah, coverage_class); mutex_unlock(&sc->lock); }