From b54bf94bf91e4ca2a489eb02bca0424ddb55242a Mon Sep 17 00:00:00 2001 From: Dominik Brodowski Date: Sat, 2 Aug 2008 14:28:43 +0200 Subject: pcmcia: use pcmcia_loop_config in net pcmcia drivers Use the config loop helper in (some) net pcmcia drivers. CC: netdev@vger.kernel.org Signed-off-by: Dominik Brodowski --- drivers/net/pcmcia/axnet_cs.c | 71 +++++----- drivers/net/pcmcia/pcnet_cs.c | 79 +++++------ drivers/net/pcmcia/smc91c92_cs.c | 96 +++++-------- drivers/net/pcmcia/xirc2ps_cs.c | 73 ++++++---- drivers/net/wireless/airo_cs.c | 230 +++++++++++++++++--------------- drivers/net/wireless/atmel_cs.c | 123 ++++++++--------- drivers/net/wireless/hostap/hostap_cs.c | 227 +++++++++++++++---------------- drivers/net/wireless/orinoco_cs.c | 176 ++++++++++++------------ drivers/net/wireless/spectrum_cs.c | 175 ++++++++++++------------ 9 files changed, 596 insertions(+), 654 deletions(-) (limited to 'drivers') diff --git a/drivers/net/pcmcia/axnet_cs.c b/drivers/net/pcmcia/axnet_cs.c index 3f682d49a4e6..04ece0b77d1d 100644 --- a/drivers/net/pcmcia/axnet_cs.c +++ b/drivers/net/pcmcia/axnet_cs.c @@ -284,58 +284,47 @@ static int try_io_port(struct pcmcia_device *link) } } +static int axnet_configcheck(struct pcmcia_device *p_dev, + cistpl_cftable_entry_t *cfg, + void *priv_data) +{ + int i; + cistpl_io_t *io = &cfg->io; + + if (cfg->index == 0 || cfg->io.nwin == 0) + return -ENODEV; + + p_dev->conf.ConfigIndex = 0x05; + /* For multifunction cards, by convention, we configure the + network function with window 0, and serial with window 1 */ + if (io->nwin > 1) { + i = (io->win[1].len > io->win[0].len); + p_dev->io.BasePort2 = io->win[1-i].base; + p_dev->io.NumPorts2 = io->win[1-i].len; + } else { + i = p_dev->io.NumPorts2 = 0; + } + p_dev->io.BasePort1 = io->win[i].base; + p_dev->io.NumPorts1 = io->win[i].len; + p_dev->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK; + if (p_dev->io.NumPorts1 + p_dev->io.NumPorts2 >= 32) + return try_io_port(p_dev); + + return -ENODEV; +} + static int axnet_config(struct pcmcia_device *link) { struct net_device *dev = link->priv; axnet_dev_t *info = PRIV(dev); - tuple_t tuple; - cisparse_t parse; int i, j, last_ret, last_fn; - u_short buf[64]; DECLARE_MAC_BUF(mac); DEBUG(0, "axnet_config(0x%p)\n", link); - tuple.Attributes = 0; - tuple.TupleData = (cisdata_t *)buf; - tuple.TupleDataMax = sizeof(buf); - tuple.TupleOffset = 0; - /* don't trust the CIS on this; Linksys got it wrong */ link->conf.Present = 0x63; - - tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY; - tuple.Attributes = 0; - CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple)); - while (last_ret == CS_SUCCESS) { - cistpl_cftable_entry_t *cfg = &(parse.cftable_entry); - cistpl_io_t *io = &(parse.cftable_entry.io); - - if (pcmcia_get_tuple_data(link, &tuple) != 0 || - pcmcia_parse_tuple(link, &tuple, &parse) != 0 || - cfg->index == 0 || cfg->io.nwin == 0) - goto next_entry; - - link->conf.ConfigIndex = 0x05; - /* For multifunction cards, by convention, we configure the - network function with window 0, and serial with window 1 */ - if (io->nwin > 1) { - i = (io->win[1].len > io->win[0].len); - link->io.BasePort2 = io->win[1-i].base; - link->io.NumPorts2 = io->win[1-i].len; - } else { - i = link->io.NumPorts2 = 0; - } - link->io.BasePort1 = io->win[i].base; - link->io.NumPorts1 = io->win[i].len; - link->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK; - if (link->io.NumPorts1 + link->io.NumPorts2 >= 32) { - last_ret = try_io_port(link); - if (last_ret == CS_SUCCESS) break; - } - next_entry: - last_ret = pcmcia_get_next_tuple(link, &tuple); - } + last_ret = pcmcia_loop_config(link, axnet_configcheck, NULL); if (last_ret != CS_SUCCESS) { cs_error(link, RequestIO, last_ret); goto failed; diff --git a/drivers/net/pcmcia/pcnet_cs.c b/drivers/net/pcmcia/pcnet_cs.c index 2d4c4ad89b8d..7a9eeca6adc2 100644 --- a/drivers/net/pcmcia/pcnet_cs.c +++ b/drivers/net/pcmcia/pcnet_cs.c @@ -512,58 +512,53 @@ static int try_io_port(struct pcmcia_device *link) } } +static int pcnet_confcheck(struct pcmcia_device *p_dev, + cistpl_cftable_entry_t *cfg, + void *priv_data) +{ + int *has_shmem = priv_data; + int i; + cistpl_io_t *io = &cfg->io; + + if (cfg->index == 0 || cfg->io.nwin == 0) + return -EINVAL; + + p_dev->conf.ConfigIndex = cfg->index; + + /* For multifunction cards, by convention, we configure the + network function with window 0, and serial with window 1 */ + if (io->nwin > 1) { + i = (io->win[1].len > io->win[0].len); + p_dev->io.BasePort2 = io->win[1-i].base; + p_dev->io.NumPorts2 = io->win[1-i].len; + } else { + i = p_dev->io.NumPorts2 = 0; + } + + *has_shmem = ((cfg->mem.nwin == 1) && + (cfg->mem.win[0].len >= 0x4000)); + p_dev->io.BasePort1 = io->win[i].base; + p_dev->io.NumPorts1 = io->win[i].len; + p_dev->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK; + if (p_dev->io.NumPorts1 + p_dev->io.NumPorts2 >= 32) + return try_io_port(p_dev); + + return 0; +} + static int pcnet_config(struct pcmcia_device *link) { struct net_device *dev = link->priv; pcnet_dev_t *info = PRIV(dev); - tuple_t tuple; - cisparse_t parse; - int i, last_ret, last_fn, start_pg, stop_pg, cm_offset; + int last_ret, last_fn, start_pg, stop_pg, cm_offset; int has_shmem = 0; - u_short buf[64]; hw_info_t *local_hw_info; DECLARE_MAC_BUF(mac); DEBUG(0, "pcnet_config(0x%p)\n", link); - tuple.TupleData = (cisdata_t *)buf; - tuple.TupleDataMax = sizeof(buf); - tuple.TupleOffset = 0; - tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY; - tuple.Attributes = 0; - CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple)); - while (last_ret == CS_SUCCESS) { - cistpl_cftable_entry_t *cfg = &(parse.cftable_entry); - cistpl_io_t *io = &(parse.cftable_entry.io); - - if (pcmcia_get_tuple_data(link, &tuple) != 0 || - pcmcia_parse_tuple(link, &tuple, &parse) != 0 || - cfg->index == 0 || cfg->io.nwin == 0) - goto next_entry; - - link->conf.ConfigIndex = cfg->index; - /* For multifunction cards, by convention, we configure the - network function with window 0, and serial with window 1 */ - if (io->nwin > 1) { - i = (io->win[1].len > io->win[0].len); - link->io.BasePort2 = io->win[1-i].base; - link->io.NumPorts2 = io->win[1-i].len; - } else { - i = link->io.NumPorts2 = 0; - } - has_shmem = ((cfg->mem.nwin == 1) && - (cfg->mem.win[0].len >= 0x4000)); - link->io.BasePort1 = io->win[i].base; - link->io.NumPorts1 = io->win[i].len; - link->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK; - if (link->io.NumPorts1 + link->io.NumPorts2 >= 32) { - last_ret = try_io_port(link); - if (last_ret == CS_SUCCESS) break; - } - next_entry: - last_ret = pcmcia_get_next_tuple(link, &tuple); - } - if (last_ret != CS_SUCCESS) { + last_ret = pcmcia_loop_config(link, pcnet_confcheck, &has_shmem); + if (last_ret) { cs_error(link, RequestIO, last_ret); goto failed; } diff --git a/drivers/net/pcmcia/smc91c92_cs.c b/drivers/net/pcmcia/smc91c92_cs.c index 250eb1954c34..c012e3400736 100644 --- a/drivers/net/pcmcia/smc91c92_cs.c +++ b/drivers/net/pcmcia/smc91c92_cs.c @@ -459,28 +459,36 @@ static int mhz_3288_power(struct pcmcia_device *link) return 0; } +static int mhz_mfc_config_check(struct pcmcia_device *p_dev, + cistpl_cftable_entry_t *cf, + void *priv_data) +{ + int k; + p_dev->conf.ConfigIndex = cf->index; + p_dev->io.BasePort2 = cf->io.win[0].base; + for (k = 0; k < 0x400; k += 0x10) { + if (k & 0x80) + continue; + p_dev->io.BasePort1 = k ^ 0x300; + if (!pcmcia_request_io(p_dev, &p_dev->io)) + return 0; + } + return -ENODEV; +} + static int mhz_mfc_config(struct pcmcia_device *link) { struct net_device *dev = link->priv; struct smc_private *smc = netdev_priv(dev); struct smc_cfg_mem *cfg_mem; - tuple_t *tuple; - cisparse_t *parse; - cistpl_cftable_entry_t *cf; - u_char *buf; win_req_t req; memreq_t mem; - int i, k; + int i; cfg_mem = kmalloc(sizeof(struct smc_cfg_mem), GFP_KERNEL); if (!cfg_mem) return CS_OUT_OF_RESOURCE; - tuple = &cfg_mem->tuple; - parse = &cfg_mem->parse; - cf = &parse->cftable_entry; - buf = cfg_mem->buf; - link->conf.Attributes |= CONF_ENABLE_SPKR; link->conf.Status = CCSR_AUDIO_ENA; link->irq.Attributes = @@ -489,27 +497,9 @@ static int mhz_mfc_config(struct pcmcia_device *link) link->io.Attributes2 = IO_DATA_PATH_WIDTH_8; link->io.NumPorts2 = 8; - tuple->Attributes = tuple->TupleOffset = 0; - tuple->TupleData = (cisdata_t *)buf; - tuple->TupleDataMax = 255; - tuple->DesiredTuple = CISTPL_CFTABLE_ENTRY; - - i = first_tuple(link, tuple, parse); /* The Megahertz combo cards have modem-like CIS entries, so we have to explicitly try a bunch of port combinations. */ - while (i == CS_SUCCESS) { - link->conf.ConfigIndex = cf->index; - link->io.BasePort2 = cf->io.win[0].base; - for (k = 0; k < 0x400; k += 0x10) { - if (k & 0x80) continue; - link->io.BasePort1 = k ^ 0x300; - i = pcmcia_request_io(link, &link->io); - if (i == CS_SUCCESS) break; - } - if (i == CS_SUCCESS) break; - i = next_tuple(link, tuple, parse); - } - if (i != CS_SUCCESS) + if (pcmcia_loop_config(link, mhz_mfc_config_check, NULL)) goto free_cfg_mem; dev->base_addr = link->io.BasePort1; @@ -533,7 +523,7 @@ static int mhz_mfc_config(struct pcmcia_device *link) free_cfg_mem: kfree(cfg_mem); - return i; + return -ENODEV; } static int mhz_setup(struct pcmcia_device *link) @@ -660,46 +650,26 @@ static int mot_setup(struct pcmcia_device *link) /*====================================================================*/ +static int smc_configcheck(struct pcmcia_device *p_dev, + cistpl_cftable_entry_t *cf, + void *priv_data) +{ + p_dev->conf.ConfigIndex = cf->index; + p_dev->io.BasePort1 = cf->io.win[0].base; + p_dev->io.IOAddrLines = cf->io.flags & CISTPL_IO_LINES_MASK; + return pcmcia_request_io(p_dev, &p_dev->io); +} + static int smc_config(struct pcmcia_device *link) { struct net_device *dev = link->priv; - struct smc_cfg_mem *cfg_mem; - tuple_t *tuple; - cisparse_t *parse; - cistpl_cftable_entry_t *cf; - u_char *buf; int i; - cfg_mem = kmalloc(sizeof(struct smc_cfg_mem), GFP_KERNEL); - if (!cfg_mem) - return CS_OUT_OF_RESOURCE; - - tuple = &cfg_mem->tuple; - parse = &cfg_mem->parse; - cf = &parse->cftable_entry; - buf = cfg_mem->buf; - - tuple->Attributes = tuple->TupleOffset = 0; - tuple->TupleData = (cisdata_t *)buf; - tuple->TupleDataMax = 255; - tuple->DesiredTuple = CISTPL_CFTABLE_ENTRY; - link->io.NumPorts1 = 16; - i = first_tuple(link, tuple, parse); - while (i != CS_NO_MORE_ITEMS) { - if (i == CS_SUCCESS) { - link->conf.ConfigIndex = cf->index; - link->io.BasePort1 = cf->io.win[0].base; - link->io.IOAddrLines = cf->io.flags & CISTPL_IO_LINES_MASK; - i = pcmcia_request_io(link, &link->io); - if (i == CS_SUCCESS) break; - } - i = next_tuple(link, tuple, parse); - } - if (i == CS_SUCCESS) - dev->base_addr = link->io.BasePort1; + i = pcmcia_loop_config(link, smc_configcheck, NULL); + if (!i) + dev->base_addr = link->io.BasePort1; - kfree(cfg_mem); return i; } diff --git a/drivers/net/pcmcia/xirc2ps_cs.c b/drivers/net/pcmcia/xirc2ps_cs.c index f6c4698ce738..b57f022952b4 100644 --- a/drivers/net/pcmcia/xirc2ps_cs.c +++ b/drivers/net/pcmcia/xirc2ps_cs.c @@ -715,6 +715,45 @@ has_ce2_string(struct pcmcia_device * p_dev) return 0; } +static int +xirc2ps_config_modem(struct pcmcia_device *p_dev, + cistpl_cftable_entry_t *cf, + void *priv_data) +{ + unsigned int ioaddr; + + if (cf->io.nwin > 0 && (cf->io.win[0].base & 0xf) == 8) { + for (ioaddr = 0x300; ioaddr < 0x400; ioaddr += 0x10) { + p_dev->conf.ConfigIndex = cf->index ; + p_dev->io.BasePort2 = cf->io.win[0].base; + p_dev->io.BasePort1 = ioaddr; + if (!pcmcia_request_io(p_dev, &p_dev->io)) + return 0; + } + } + return -ENODEV; +} + +static int +xirc2ps_config_check(struct pcmcia_device *p_dev, + cistpl_cftable_entry_t *cf, + void *priv_data) +{ + int *pass = priv_data; + + if (cf->io.nwin > 0 && (cf->io.win[0].base & 0xf) == 8) { + p_dev->conf.ConfigIndex = cf->index ; + p_dev->io.BasePort2 = cf->io.win[0].base; + p_dev->io.BasePort1 = p_dev->io.BasePort2 + + (*pass ? (cf->index & 0x20 ? -24:8) + : (cf->index & 0x20 ? 8:-24)); + if (!pcmcia_request_io(p_dev, &p_dev->io)) + return 0; + } + return -ENODEV; + +} + /**************** * xirc2ps_config() is scheduled to run after a CARD_INSERTION event * is received, to configure the PCMCIA socket, and to make the @@ -725,13 +764,12 @@ xirc2ps_config(struct pcmcia_device * link) { struct net_device *dev = link->priv; local_info_t *local = netdev_priv(dev); + unsigned int ioaddr; tuple_t tuple; cisparse_t parse; - unsigned int ioaddr; int err, i; u_char buf[64]; cistpl_lan_node_id_t *node_id = (cistpl_lan_node_id_t*)parse.funce.data; - cistpl_cftable_entry_t *cf = &parse.cftable_entry; DECLARE_MAC_BUF(mac); local->dingo_ccr = NULL; @@ -846,19 +884,8 @@ xirc2ps_config(struct pcmcia_device * link) /* Take the Modem IO port from the CIS and scan for a free * Ethernet port */ link->io.NumPorts1 = 16; /* no Mako stuff anymore */ - tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY; - for (err = first_tuple(link, &tuple, &parse); !err; - err = next_tuple(link, &tuple, &parse)) { - if (cf->io.nwin > 0 && (cf->io.win[0].base & 0xf) == 8) { - for (ioaddr = 0x300; ioaddr < 0x400; ioaddr += 0x10) { - link->conf.ConfigIndex = cf->index ; - link->io.BasePort2 = cf->io.win[0].base; - link->io.BasePort1 = ioaddr; - if (!(err=pcmcia_request_io(link, &link->io))) - goto port_found; - } - } - } + if (!pcmcia_loop_config(link, xirc2ps_config_modem, NULL)) + goto port_found; } else { link->io.NumPorts1 = 18; /* We do 2 passes here: The first one uses the regular mapping and @@ -866,21 +893,9 @@ xirc2ps_config(struct pcmcia_device * link) * mirrored every 32 bytes. Actually we use a mirrored port for * the Mako if (on the first pass) the COR bit 5 is set. */ - for (pass=0; pass < 2; pass++) { - tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY; - for (err = first_tuple(link, &tuple, &parse); !err; - err = next_tuple(link, &tuple, &parse)){ - if (cf->io.nwin > 0 && (cf->io.win[0].base & 0xf) == 8){ - link->conf.ConfigIndex = cf->index ; - link->io.BasePort2 = cf->io.win[0].base; - link->io.BasePort1 = link->io.BasePort2 - + (pass ? (cf->index & 0x20 ? -24:8) - : (cf->index & 0x20 ? 8:-24)); - if (!(err=pcmcia_request_io(link, &link->io))) + for (pass=0; pass < 2; pass++) + if (!pcmcia_loop_config(link, xirc2ps_config_check, &pass)) goto port_found; - } - } - } /* if special option: * try to configure as Ethernet only. * .... */ diff --git a/drivers/net/wireless/airo_cs.c b/drivers/net/wireless/airo_cs.c index f12355398fe7..4fbe811bebfc 100644 --- a/drivers/net/wireless/airo_cs.c +++ b/drivers/net/wireless/airo_cs.c @@ -206,126 +206,131 @@ static void airo_detach(struct pcmcia_device *link) #define CS_CHECK(fn, ret) \ do { last_fn = (fn); if ((last_ret = (ret)) != 0) goto cs_failed; } while (0) +struct airo_cs_config_data { + cistpl_cftable_entry_t dflt; + win_req_t req; +}; + +static int airo_cs_config_check(struct pcmcia_device *p_dev, + cistpl_cftable_entry_t *cfg, + void *priv_data) +{ + struct airo_cs_config_data *cfg_mem = priv_data; + + if (cfg->flags & CISTPL_CFTABLE_DEFAULT) + cfg_mem->dflt = *cfg; + + if (cfg->index == 0) + return -ENODEV; + + p_dev->conf.ConfigIndex = cfg->index; + + /* Does this card need audio output? */ + if (cfg->flags & CISTPL_CFTABLE_AUDIO) { + p_dev->conf.Attributes |= CONF_ENABLE_SPKR; + p_dev->conf.Status = CCSR_AUDIO_ENA; + } + + /* Use power settings for Vcc and Vpp if present */ + /* Note that the CIS values need to be rescaled */ + if (cfg->vpp1.present & (1<conf.Vpp = cfg->vpp1.param[CISTPL_POWER_VNOM]/10000; + else if (cfg_mem->dflt.vpp1.present & (1<conf.Vpp = cfg_mem->dflt.vpp1.param[CISTPL_POWER_VNOM]/10000; + + /* Do we need to allocate an interrupt? */ + if (cfg->irq.IRQInfo1 || cfg_mem->dflt.irq.IRQInfo1) + p_dev->conf.Attributes |= CONF_ENABLE_IRQ; + + /* IO window settings */ + p_dev->io.NumPorts1 = p_dev->io.NumPorts2 = 0; + if ((cfg->io.nwin > 0) || (cfg_mem->dflt.io.nwin > 0)) { + cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &cfg_mem->dflt.io; + p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO; + if (!(io->flags & CISTPL_IO_8BIT)) + p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_16; + if (!(io->flags & CISTPL_IO_16BIT)) + p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_8; + p_dev->io.BasePort1 = io->win[0].base; + p_dev->io.NumPorts1 = io->win[0].len; + if (io->nwin > 1) { + p_dev->io.Attributes2 = p_dev->io.Attributes1; + p_dev->io.BasePort2 = io->win[1].base; + p_dev->io.NumPorts2 = io->win[1].len; + } + } + + /* This reserves IO space but doesn't actually enable it */ + if (pcmcia_request_io(p_dev, &p_dev->io) != 0) + return -ENODEV; + + /* + Now set up a common memory window, if needed. There is room + in the struct pcmcia_device structure for one memory window handle, + but if the base addresses need to be saved, or if multiple + windows are needed, the info should go in the private data + structure for this device. + + Note that the memory window base is a physical address, and + needs to be mapped to virtual space with ioremap() before it + is used. + */ + if ((cfg->mem.nwin > 0) || (cfg_mem->dflt.mem.nwin > 0)) { + cistpl_mem_t *mem = (cfg->mem.nwin) ? &cfg->mem : &cfg_mem->dflt.mem; + memreq_t map; + cfg_mem->req.Attributes = WIN_DATA_WIDTH_16|WIN_MEMORY_TYPE_CM; + cfg_mem->req.Base = mem->win[0].host_addr; + cfg_mem->req.Size = mem->win[0].len; + cfg_mem->req.AccessSpeed = 0; + if (pcmcia_request_window(&p_dev, &cfg_mem->req, &p_dev->win) != 0) + return -ENODEV; + map.Page = 0; + map.CardOffset = mem->win[0].card_addr; + if (pcmcia_map_mem_page(p_dev->win, &map) != 0) + return -ENODEV; + } + /* If we got this far, we're cool! */ + return 0; +} + + static int airo_config(struct pcmcia_device *link) { - tuple_t tuple; - cisparse_t parse; local_info_t *dev; + struct airo_cs_config_data *cfg_mem; int last_fn, last_ret; - u_char buf[64]; - win_req_t req; - memreq_t map; dev = link->priv; DEBUG(0, "airo_config(0x%p)\n", link); + cfg_mem = kzalloc(sizeof(struct airo_cs_config_data), GFP_KERNEL); + if (!cfg_mem) + return -ENOMEM; + /* - In this loop, we scan the CIS for configuration table entries, - each of which describes a valid card configuration, including - voltage, IO window, memory window, and interrupt settings. - - We make no assumptions about the card to be configured: we use - just the information available in the CIS. In an ideal world, - this would work for any PCMCIA card, but it requires a complete - and accurate CIS. In practice, a driver usually "knows" most of - these things without consulting the CIS, and most client drivers - will only use the CIS to fill in implementation-defined details. + * In this loop, we scan the CIS for configuration table + * entries, each of which describes a valid card + * configuration, including voltage, IO window, memory window, + * and interrupt settings. + * + * We make no assumptions about the card to be configured: we + * use just the information available in the CIS. In an ideal + * world, this would work for any PCMCIA card, but it requires + * a complete and accurate CIS. In practice, a driver usually + * "knows" most of these things without consulting the CIS, + * and most client drivers will only use the CIS to fill in + * implementation-defined details. + */ + last_ret = pcmcia_loop_config(link, airo_cs_config_check, cfg_mem); + if (last_ret) + goto failed; + + /* + Allocate an interrupt line. Note that this does not assign a + handler to the interrupt, unless the 'Handler' member of the + irq structure is initialized. */ - tuple.Attributes = 0; - tuple.TupleData = buf; - tuple.TupleDataMax = sizeof(buf); - tuple.TupleOffset = 0; - tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY; - CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple)); - while (1) { - cistpl_cftable_entry_t dflt = { 0 }; - cistpl_cftable_entry_t *cfg = &(parse.cftable_entry); - if (pcmcia_get_tuple_data(link, &tuple) != 0 || - pcmcia_parse_tuple(link, &tuple, &parse) != 0) - goto next_entry; - - if (cfg->flags & CISTPL_CFTABLE_DEFAULT) dflt = *cfg; - if (cfg->index == 0) goto next_entry; - link->conf.ConfigIndex = cfg->index; - - /* Does this card need audio output? */ - if (cfg->flags & CISTPL_CFTABLE_AUDIO) { - link->conf.Attributes |= CONF_ENABLE_SPKR; - link->conf.Status = CCSR_AUDIO_ENA; - } - - /* Use power settings for Vcc and Vpp if present */ - /* Note that the CIS values need to be rescaled */ - if (cfg->vpp1.present & (1<conf.Vpp = - cfg->vpp1.param[CISTPL_POWER_VNOM]/10000; - else if (dflt.vpp1.present & (1<conf.Vpp = - dflt.vpp1.param[CISTPL_POWER_VNOM]/10000; - - /* Do we need to allocate an interrupt? */ - if (cfg->irq.IRQInfo1 || dflt.irq.IRQInfo1) - link->conf.Attributes |= CONF_ENABLE_IRQ; - - /* IO window settings */ - link->io.NumPorts1 = link->io.NumPorts2 = 0; - if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) { - cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt.io; - link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO; - if (!(io->flags & CISTPL_IO_8BIT)) - link->io.Attributes1 = IO_DATA_PATH_WIDTH_16; - if (!(io->flags & CISTPL_IO_16BIT)) - link->io.Attributes1 = IO_DATA_PATH_WIDTH_8; - link->io.BasePort1 = io->win[0].base; - link->io.NumPorts1 = io->win[0].len; - if (io->nwin > 1) { - link->io.Attributes2 = link->io.Attributes1; - link->io.BasePort2 = io->win[1].base; - link->io.NumPorts2 = io->win[1].len; - } - } - - /* This reserves IO space but doesn't actually enable it */ - if (pcmcia_request_io(link, &link->io) != 0) - goto next_entry; - - /* - Now set up a common memory window, if needed. There is room - in the struct pcmcia_device structure for one memory window handle, - but if the base addresses need to be saved, or if multiple - windows are needed, the info should go in the private data - structure for this device. - - Note that the memory window base is a physical address, and - needs to be mapped to virtual space with ioremap() before it - is used. - */ - if ((cfg->mem.nwin > 0) || (dflt.mem.nwin > 0)) { - cistpl_mem_t *mem = - (cfg->mem.nwin) ? &cfg->mem : &dflt.mem; - req.Attributes = WIN_DATA_WIDTH_16|WIN_MEMORY_TYPE_CM; - req.Base = mem->win[0].host_addr; - req.Size = mem->win[0].len; - req.AccessSpeed = 0; - if (pcmcia_request_window(&link, &req, &link->win) != 0) - goto next_entry; - map.Page = 0; map.CardOffset = mem->win[0].card_addr; - if (pcmcia_map_mem_page(link->win, &map) != 0) - goto next_entry; - } - /* If we got this far, we're cool! */ - break; - - next_entry: - CS_CHECK(GetNextTuple, pcmcia_get_next_tuple(link, &tuple)); - } - - /* - Allocate an interrupt line. Note that this does not assign a - handler to the interrupt, unless the 'Handler' member of the - irq structure is initialized. - */ if (link->conf.Attributes & CONF_ENABLE_IRQ) CS_CHECK(RequestIRQ, pcmcia_request_irq(link, &link->irq)); @@ -362,14 +367,17 @@ static int airo_config(struct pcmcia_device *link) printk(" & 0x%04x-0x%04x", link->io.BasePort2, link->io.BasePort2+link->io.NumPorts2-1); if (link->win) - printk(", mem 0x%06lx-0x%06lx", req.Base, - req.Base+req.Size-1); + printk(", mem 0x%06lx-0x%06lx", cfg_mem->req.Base, + cfg_mem->req.Base+cfg_mem->req.Size-1); printk("\n"); + kfree(cfg_mem); return 0; cs_failed: cs_error(link, last_fn, last_ret); + failed: airo_release(link); + kfree(cfg_mem); return -ENODEV; } /* airo_config */ diff --git a/drivers/net/wireless/atmel_cs.c b/drivers/net/wireless/atmel_cs.c index 12617cd0b78e..263c36f7ee22 100644 --- a/drivers/net/wireless/atmel_cs.c +++ b/drivers/net/wireless/atmel_cs.c @@ -224,25 +224,69 @@ static int card_present(void *arg) return 0; } +static int atmel_config_check(struct pcmcia_device *p_dev, + cistpl_cftable_entry_t *cfg, + void *priv_data) +{ + cistpl_cftable_entry_t *dflt = priv_data; + + if (cfg->flags & CISTPL_CFTABLE_DEFAULT) + *dflt = *cfg; + if (cfg->index == 0) + return -ENODEV; + p_dev->conf.ConfigIndex = cfg->index; + + /* Does this card need audio output? */ + if (cfg->flags & CISTPL_CFTABLE_AUDIO) { + p_dev->conf.Attributes |= CONF_ENABLE_SPKR; + p_dev->conf.Status = CCSR_AUDIO_ENA; + } + + /* Use power settings for Vcc and Vpp if present */ + /* Note that the CIS values need to be rescaled */ + if (cfg->vpp1.present & (1<conf.Vpp = cfg->vpp1.param[CISTPL_POWER_VNOM]/10000; + else if (dflt->vpp1.present & (1<conf.Vpp = dflt->vpp1.param[CISTPL_POWER_VNOM]/10000; + + /* Do we need to allocate an interrupt? */ + if (cfg->irq.IRQInfo1 || dflt->irq.IRQInfo1) + p_dev->conf.Attributes |= CONF_ENABLE_IRQ; + + /* IO window settings */ + p_dev->io.NumPorts1 = p_dev->io.NumPorts2 = 0; + if ((cfg->io.nwin > 0) || (dflt->io.nwin > 0)) { + cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt->io; + p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO; + if (!(io->flags & CISTPL_IO_8BIT)) + p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_16; + if (!(io->flags & CISTPL_IO_16BIT)) + p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_8; + p_dev->io.BasePort1 = io->win[0].base; + p_dev->io.NumPorts1 = io->win[0].len; + if (io->nwin > 1) { + p_dev->io.Attributes2 = p_dev->io.Attributes1; + p_dev->io.BasePort2 = io->win[1].base; + p_dev->io.NumPorts2 = io->win[1].len; + } + } + + /* This reserves IO space but doesn't actually enable it */ + return pcmcia_request_io(p_dev, &p_dev->io); +} + static int atmel_config(struct pcmcia_device *link) { - tuple_t tuple; - cisparse_t parse; local_info_t *dev; int last_fn, last_ret; - u_char buf[64]; struct pcmcia_device_id *did; + cistpl_cftable_entry_t dflt = { 0 }; dev = link->priv; did = handle_to_dev(link).driver_data; DEBUG(0, "atmel_config(0x%p)\n", link); - tuple.Attributes = 0; - tuple.TupleData = buf; - tuple.TupleDataMax = sizeof(buf); - tuple.TupleOffset = 0; - /* In this loop, we scan the CIS for configuration table entries, each of which describes a valid card configuration, including @@ -255,66 +299,8 @@ static int atmel_config(struct pcmcia_device *link) these things without consulting the CIS, and most client drivers will only use the CIS to fill in implementation-defined details. */ - tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY; - CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple)); - while (1) { - cistpl_cftable_entry_t dflt = { 0 }; - cistpl_cftable_entry_t *cfg = &(parse.cftable_entry); - if (pcmcia_get_tuple_data(link, &tuple) != 0 || - pcmcia_parse_tuple(link, &tuple, &parse) != 0) - goto next_entry; - - if (cfg->flags & CISTPL_CFTABLE_DEFAULT) dflt = *cfg; - if (cfg->index == 0) goto next_entry; - link->conf.ConfigIndex = cfg->index; - - /* Does this card need audio output? */ - if (cfg->flags & CISTPL_CFTABLE_AUDIO) { - link->conf.Attributes |= CONF_ENABLE_SPKR; - link->conf.Status = CCSR_AUDIO_ENA; - } - - /* Use power settings for Vcc and Vpp if present */ - /* Note that the CIS values need to be rescaled */ - if (cfg->vpp1.present & (1<conf.Vpp = - cfg->vpp1.param[CISTPL_POWER_VNOM]/10000; - else if (dflt.vpp1.present & (1<conf.Vpp = - dflt.vpp1.param[CISTPL_POWER_VNOM]/10000; - - /* Do we need to allocate an interrupt? */ - if (cfg->irq.IRQInfo1 || dflt.irq.IRQInfo1) - link->conf.Attributes |= CONF_ENABLE_IRQ; - - /* IO window settings */ - link->io.NumPorts1 = link->io.NumPorts2 = 0; - if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) { - cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt.io; - link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO; - if (!(io->flags & CISTPL_IO_8BIT)) - link->io.Attributes1 = IO_DATA_PATH_WIDTH_16; - if (!(io->flags & CISTPL_IO_16BIT)) - link->io.Attributes1 = IO_DATA_PATH_WIDTH_8; - link->io.BasePort1 = io->win[0].base; - link->io.NumPorts1 = io->win[0].len; - if (io->nwin > 1) { - link->io.Attributes2 = link->io.Attributes1; - link->io.BasePort2 = io->win[1].base; - link->io.NumPorts2 = io->win[1].len; - } - } - - /* This reserves IO space but doesn't actually enable it */ - if (pcmcia_request_io(link, &link->io) != 0) - goto next_entry; - - /* If we got this far, we're cool! */ - break; - - next_entry: - CS_CHECK(GetNextTuple, pcmcia_get_next_tuple(link, &tuple)); - } + if (pcmcia_loop_config(link, atmel_config_check, &dflt)) + goto failed; /* Allocate an interrupt line. Note that this does not assign a @@ -360,6 +346,7 @@ static int atmel_config(struct pcmcia_device *link) cs_failed: cs_error(link, last_fn, last_ret); + failed: atmel_release(link); return -ENODEV; } diff --git a/drivers/net/wireless/hostap/hostap_cs.c b/drivers/net/wireless/hostap/hostap_cs.c index 3b4e55cf33cd..3d914dde5de0 100644 --- a/drivers/net/wireless/hostap/hostap_cs.c +++ b/drivers/net/wireless/hostap/hostap_cs.c @@ -532,145 +532,134 @@ static void prism2_detach(struct pcmcia_device *link) #define CS_CHECK(fn, ret) \ do { last_fn = (fn); if ((last_ret = (ret)) != 0) goto cs_failed; } while (0) -#define CFG_CHECK2(fn, retf) \ -do { int _ret = (retf); \ -if (_ret != 0) { \ - PDEBUG(DEBUG_EXTRA, "CardServices(" #fn ") returned %d\n", _ret); \ - cs_error(link, fn, _ret); \ - goto next_entry; \ -} \ -} while (0) - /* run after a CARD_INSERTION event is received to configure the PCMCIA * socket and make the device available to the system */ + +struct prism2_config_data { + cistpl_cftable_entry_t dflt; + config_info_t conf; +}; + +static int prism2_config_check(struct pcmcia_device *p_dev, + cistpl_cftable_entry_t *cfg, + void *priv_data) +{ + struct prism2_config_data *cfg_mem = priv_data; + + if (cfg->flags & CISTPL_CFTABLE_DEFAULT) + cfg_mem->dflt = *cfg; + if (cfg->index == 0) + return -ENODEV; + + p_dev->conf.ConfigIndex = cfg->index; + PDEBUG(DEBUG_EXTRA, "Checking CFTABLE_ENTRY 0x%02X " + "(default 0x%02X)\n", cfg->index, cfg_mem->dflt.index); + + /* Does this card need audio output? */ + if (cfg->flags & CISTPL_CFTABLE_AUDIO) { + p_dev->conf.Attributes |= CONF_ENABLE_SPKR; + p_dev->conf.Status = CCSR_AUDIO_ENA; + } + + /* Use power settings for Vcc and Vpp if present */ + /* Note that the CIS values need to be rescaled */ + if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) { + if (cfg_mem->conf.Vcc != cfg->vcc.param[CISTPL_POWER_VNOM] / + 10000 && !ignore_cis_vcc) { + PDEBUG(DEBUG_EXTRA, " Vcc mismatch - skipping" + " this entry\n"); + return -ENODEV; + } + } else if (cfg_mem->dflt.vcc.present & (1 << CISTPL_POWER_VNOM)) { + if (cfg_mem->conf.Vcc != cfg_mem->dflt.vcc.param[CISTPL_POWER_VNOM] / + 10000 && !ignore_cis_vcc) { + PDEBUG(DEBUG_EXTRA, " Vcc (default) mismatch " + "- skipping this entry\n"); + return -ENODEV; + } + } + + if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM)) + p_dev->conf.Vpp = cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000; + else if (cfg_mem->dflt.vpp1.present & (1 << CISTPL_POWER_VNOM)) + p_dev->conf.Vpp = cfg_mem->dflt.vpp1.param[CISTPL_POWER_VNOM] / 10000; + + /* Do we need to allocate an interrupt? */ + if (cfg->irq.IRQInfo1 || cfg_mem->dflt.irq.IRQInfo1) + p_dev->conf.Attributes |= CONF_ENABLE_IRQ; + else if (!(p_dev->conf.Attributes & CONF_ENABLE_IRQ)) { + /* At least Compaq WL200 does not have IRQInfo1 set, + * but it does not work without interrupts.. */ + printk(KERN_WARNING "Config has no IRQ info, but trying to " + "enable IRQ anyway..\n"); + p_dev->conf.Attributes |= CONF_ENABLE_IRQ; + } + + /* IO window settings */ + PDEBUG(DEBUG_EXTRA, "IO window settings: cfg->io.nwin=%d " + "cfg_mem->dflt.io.nwin=%d\n", + cfg->io.nwin, cfg_mem->dflt.io.nwin); + p_dev->io.NumPorts1 = p_dev->io.NumPorts2 = 0; + if ((cfg->io.nwin > 0) || (cfg_mem->dflt.io.nwin > 0)) { + cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &cfg_mem->dflt.io; + p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO; + PDEBUG(DEBUG_EXTRA, "io->flags = 0x%04X, " + "io.base=0x%04x, len=%d\n", io->flags, + io->win[0].base, io->win[0].len); + if (!(io->flags & CISTPL_IO_8BIT)) + p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_16; + if (!(io->flags & CISTPL_IO_16BIT)) + p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_8; + p_dev->io.IOAddrLines = io->flags & + CISTPL_IO_LINES_MASK; + p_dev->io.BasePort1 = io->win[0].base; + p_dev->io.NumPorts1 = io->win[0].len; + if (io->nwin > 1) { + p_dev->io.Attributes2 = p_dev->io.Attributes1; + p_dev->io.BasePort2 = io->win[1].base; + p_dev->io.NumPorts2 = io->win[1].len; + } + } + + /* This reserves IO space but doesn't actually enable it */ + return pcmcia_request_io(p_dev, &p_dev->io); +} + static int prism2_config(struct pcmcia_device *link) { struct net_device *dev; struct hostap_interface *iface; + struct prism2_config_data *cfg_mem; local_info_t *local; int ret = 1; - tuple_t tuple; - cisparse_t *parse; int last_fn, last_ret; - u_char buf[64]; - config_info_t conf; - cistpl_cftable_entry_t dflt = { 0 }; struct hostap_cs_priv *hw_priv; PDEBUG(DEBUG_FLOW, "prism2_config()\n"); - parse = kmalloc(sizeof(cisparse_t), GFP_KERNEL); + cfg_mem = kzalloc(sizeof(struct prism2_config_data), GFP_KERNEL); + if (!cfg_mem) + return -ENOMEM; + hw_priv = kzalloc(sizeof(*hw_priv), GFP_KERNEL); - if (parse == NULL || hw_priv == NULL) { + if (hw_priv == NULL) { ret = -ENOMEM; goto failed; } - tuple.Attributes = 0; - tuple.TupleData = buf; - tuple.TupleDataMax = sizeof(buf); - tuple.TupleOffset = 0; - CS_CHECK(GetConfigurationInfo, - pcmcia_get_configuration_info(link, &conf)); + pcmcia_get_configuration_info(link, &cfg_mem->conf)); /* Look for an appropriate configuration table entry in the CIS */ - tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY; - CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple)); - for (;;) { - cistpl_cftable_entry_t *cfg = &(parse->cftable_entry); - CFG_CHECK2(GetTupleData, - pcmcia_get_tuple_data(link, &tuple)); - CFG_CHECK2(ParseTuple, - pcmcia_parse_tuple(link, &tuple, parse)); - - if (cfg->flags & CISTPL_CFTABLE_DEFAULT) - dflt = *cfg; - if (cfg->index == 0) - goto next_entry; - link->conf.ConfigIndex = cfg->index; - PDEBUG(DEBUG_EXTRA, "Checking CFTABLE_ENTRY 0x%02X " - "(default 0x%02X)\n", cfg->index, dflt.index); - - /* Does this card need audio output? */ - if (cfg->flags & CISTPL_CFTABLE_AUDIO) { - link->conf.Attributes |= CONF_ENABLE_SPKR; - link->conf.Status = CCSR_AUDIO_ENA; - } - - /* Use power settings for Vcc and Vpp if present */ - /* Note that the CIS values need to be rescaled */ - if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) { - if (conf.Vcc != cfg->vcc.param[CISTPL_POWER_VNOM] / - 10000 && !ignore_cis_vcc) { - PDEBUG(DEBUG_EXTRA, " Vcc mismatch - skipping" - " this entry\n"); - goto next_entry; - } - } else if (dflt.vcc.present & (1 << CISTPL_POWER_VNOM)) { - if (conf.Vcc != dflt.vcc.param[CISTPL_POWER_VNOM] / - 10000 && !ignore_cis_vcc) { - PDEBUG(DEBUG_EXTRA, " Vcc (default) mismatch " - "- skipping this entry\n"); - goto next_entry; - } - } - - if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM)) - link->conf.Vpp = - cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000; - else if (dflt.vpp1.present & (1 << CISTPL_POWER_VNOM)) - link->conf.Vpp = - dflt.vpp1.param[CISTPL_POWER_VNOM] / 10000; - - /* Do we need to allocate an interrupt? */ - if (cfg->irq.IRQInfo1 || dflt.irq.IRQInfo1) - link->conf.Attributes |= CONF_ENABLE_IRQ; - else if (!(link->conf.Attributes & CONF_ENABLE_IRQ)) { - /* At least Compaq WL200 does not have IRQInfo1 set, - * but it does not work without interrupts.. */ - printk("Config has no IRQ info, but trying to enable " - "IRQ anyway..\n"); - link->conf.Attributes |= CONF_ENABLE_IRQ; - } - - /* IO window settings */ - PDEBUG(DEBUG_EXTRA, "IO window settings: cfg->io.nwin=%d " - "dflt.io.nwin=%d\n", - cfg->io.nwin, dflt.io.nwin); - link->io.NumPorts1 = link->io.NumPorts2 = 0; - if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) { - cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &dflt.io; - link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO; - PDEBUG(DEBUG_EXTRA, "io->flags = 0x%04X, " - "io.base=0x%04x, len=%d\n", io->flags, - io->win[0].base, io->win[0].len); - if (!(io->flags & CISTPL_IO_8BIT)) - link->io.Attributes1 = IO_DATA_PATH_WIDTH_16; - if (!(io->flags & CISTPL_IO_16BIT)) - link->io.Attributes1 = IO_DATA_PATH_WIDTH_8; - link->io.IOAddrLines = io->flags & - CISTPL_IO_LINES_MASK; - link->io.BasePort1 = io->win[0].base; - link->io.NumPorts1 = io->win[0].len; - if (io->nwin > 1) { - link->io.Attributes2 = link->io.Attributes1; - link->io.BasePort2 = io->win[1].base; - link->io.NumPorts2 = io->win[1].len; - } - } - - /* This reserves IO space but doesn't actually enable it */ - CFG_CHECK2(RequestIO, - pcmcia_request_io(link, &link->io)); - - /* This configuration table entry is OK */ - break; - - next_entry: - CS_CHECK(GetNextTuple, - pcmcia_get_next_tuple(link, &tuple)); + last_ret = pcmcia_loop_config(link, prism2_config_check, cfg_mem); + if (last_ret) { + if (!ignore_cis_vcc) + printk(KERN_ERR "GetNextTuple(): No matching " + "CIS configuration. Maybe you need the " + "ignore_cis_vcc=1 parameter.\n"); + cs_error(link, RequestIO, last_ret); + goto failed; } /* Need to allocate net_device before requesting IRQ handler */ @@ -738,15 +727,15 @@ static int prism2_config(struct pcmcia_device *link) if (ret == 0 && local->ddev) strcpy(hw_priv->node.dev_name, local->ddev->name); } - kfree(parse); + kfree(cfg_mem); return ret; cs_failed: cs_error(link, last_fn, last_ret); failed: - kfree(parse); kfree(hw_priv); + kfree(cfg_mem); prism2_release((u_long)link); return ret; } diff --git a/drivers/net/wireless/orinoco_cs.c b/drivers/net/wireless/orinoco_cs.c index 1c216e015f64..473370c9e0d6 100644 --- a/drivers/net/wireless/orinoco_cs.c +++ b/drivers/net/wireless/orinoco_cs.c @@ -164,23 +164,96 @@ static void orinoco_cs_detach(struct pcmcia_device *link) last_fn = (fn); if ((last_ret = (ret)) != 0) goto cs_failed; \ } while (0) +struct orinoco_cs_config_data { + cistpl_cftable_entry_t dflt; + config_info_t conf; +}; + +static int orinoco_cs_config_check(struct pcmcia_device *p_dev, + cistpl_cftable_entry_t *cfg, + void *priv_data) +{ + struct orinoco_cs_config_data *cfg_mem = priv_data; + + if (cfg->flags & CISTPL_CFTABLE_DEFAULT) + cfg_mem->dflt = *cfg; + if (cfg->index == 0) + goto next_entry; + p_dev->conf.ConfigIndex = cfg->index; + + /* Use power settings for Vcc and Vpp if present */ + /* Note that the CIS values need to be rescaled */ + if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) { + if (cfg_mem->conf.Vcc != cfg->vcc.param[CISTPL_POWER_VNOM] / 10000) { + DEBUG(2, "spectrum_cs_config: Vcc mismatch (cfg_mem->conf.Vcc = %d, CIS = %d)\n", cfg_mem->conf.Vcc, cfg->vcc.param[CISTPL_POWER_VNOM] / 10000); + if (!ignore_cis_vcc) + goto next_entry; + } + } else if (cfg_mem->dflt.vcc.present & (1 << CISTPL_POWER_VNOM)) { + if (cfg_mem->conf.Vcc != cfg_mem->dflt.vcc.param[CISTPL_POWER_VNOM] / 10000) { + DEBUG(2, "spectrum_cs_config: Vcc mismatch (cfg_mem->conf.Vcc = %d, CIS = %d)\n", cfg_mem->conf.Vcc, cfg_mem->dflt.vcc.param[CISTPL_POWER_VNOM] / 10000); + if (!ignore_cis_vcc) + goto next_entry; + } + } + + if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM)) + p_dev->conf.Vpp = + cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000; + else if (cfg_mem->dflt.vpp1.present & (1 << CISTPL_POWER_VNOM)) + p_dev->conf.Vpp = + cfg_mem->dflt.vpp1.param[CISTPL_POWER_VNOM] / 10000; + + /* Do we need to allocate an interrupt? */ + p_dev->conf.Attributes |= CONF_ENABLE_IRQ; + + /* IO window settings */ + p_dev->io.NumPorts1 = p_dev->io.NumPorts2 = 0; + if ((cfg->io.nwin > 0) || (cfg_mem->dflt.io.nwin > 0)) { + cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &cfg_mem->dflt.io; + p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO; + if (!(io->flags & CISTPL_IO_8BIT)) + p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_16; + if (!(io->flags & CISTPL_IO_16BIT)) + p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_8; + p_dev->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK; + p_dev->io.BasePort1 = io->win[0].base; + p_dev->io.NumPorts1 = io->win[0].len; + if (io->nwin > 1) { + p_dev->io.Attributes2 = p_dev->io.Attributes1; + p_dev->io.BasePort2 = io->win[1].base; + p_dev->io.NumPorts2 = io->win[1].len; + } + + /* This reserves IO space but doesn't actually enable it */ + if (pcmcia_request_io(p_dev, &p_dev->io) != 0) + goto next_entry; + } + return 0; + +next_entry: + pcmcia_disable_device(p_dev); + return -ENODEV; +}; + static int orinoco_cs_config(struct pcmcia_device *link) { + struct orinoco_cs_config_data *cfg_mem; struct net_device *dev = link->priv; struct orinoco_private *priv = netdev_priv(dev); struct orinoco_pccard *card = priv->card; hermes_t *hw = &priv->hw; int last_fn, last_ret; - u_char buf[64]; - config_info_t conf; - tuple_t tuple; - cisparse_t parse; void __iomem *mem; + cfg_mem = kzalloc(sizeof(struct orinoco_cs_config_data), GFP_KERNEL); + if (!cfg_mem) + return -ENOMEM; + /* Look up the current Vcc */ CS_CHECK(GetConfigurationInfo, - pcmcia_get_configuration_info(link, &conf)); + pcmcia_get_configuration_info(link, &cfg_mem->conf)); /* * In this loop, we scan the CIS for configuration table @@ -196,94 +269,14 @@ orinoco_cs_config(struct pcmcia_device *link) * and most client drivers will only use the CIS to fill in * implementation-defined details. */ - tuple.Attributes = 0; - tuple.TupleData = buf; - tuple.TupleDataMax = sizeof(buf); - tuple.TupleOffset = 0; - tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY; - CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple)); - while (1) { - cistpl_cftable_entry_t *cfg = &(parse.cftable_entry); - cistpl_cftable_entry_t dflt = { .index = 0 }; - - if ( (pcmcia_get_tuple_data(link, &tuple) != 0) - || (pcmcia_parse_tuple(link, &tuple, &parse) != 0)) - goto next_entry; - - if (cfg->flags & CISTPL_CFTABLE_DEFAULT) - dflt = *cfg; - if (cfg->index == 0) - goto next_entry; - link->conf.ConfigIndex = cfg->index; - - /* Use power settings for Vcc and Vpp if present */ - /* Note that the CIS values need to be rescaled */ - if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) { - if (conf.Vcc != cfg->vcc.param[CISTPL_POWER_VNOM] / 10000) { - DEBUG(2, "orinoco_cs_config: Vcc mismatch (conf.Vcc = %d, cfg CIS = %d)\n", conf.Vcc, cfg->vcc.param[CISTPL_POWER_VNOM] / 10000); - if (!ignore_cis_vcc) - goto next_entry; - } - } else if (dflt.vcc.present & (1 << CISTPL_POWER_VNOM)) { - if (conf.Vcc != dflt.vcc.param[CISTPL_POWER_VNOM] / 10000) { - DEBUG(2, "orinoco_cs_config: Vcc mismatch (conf.Vcc = %d, dflt CIS = %d)\n", conf.Vcc, dflt.vcc.param[CISTPL_POWER_VNOM] / 10000); - if(!ignore_cis_vcc) - goto next_entry; - } - } - - if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM)) - link->conf.Vpp = - cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000; - else if (dflt.vpp1.present & (1 << CISTPL_POWER_VNOM)) - link->conf.Vpp = - dflt.vpp1.param[CISTPL_POWER_VNOM] / 10000; - - /* Do we need to allocate an interrupt? */ - link->conf.Attributes |= CONF_ENABLE_IRQ; - - /* IO window settings */ - link->io.NumPorts1 = link->io.NumPorts2 = 0; - if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) { - cistpl_io_t *io = - (cfg->io.nwin) ? &cfg->io : &dflt.io; - link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO; - if (!(io->flags & CISTPL_IO_8BIT)) - link->io.Attributes1 = - IO_DATA_PATH_WIDTH_16; - if (!(io->flags & CISTPL_IO_16BIT)) - link->io.Attributes1 = - IO_DATA_PATH_WIDTH_8; - link->io.IOAddrLines = - io->flags & CISTPL_IO_LINES_MASK; - link->io.BasePort1 = io->win[0].base; - link->io.NumPorts1 = io->win[0].len; - if (io->nwin > 1) { - link->io.Attributes2 = - link->io.Attributes1; - link->io.BasePort2 = io->win[1].base; - link->io.NumPorts2 = io->win[1].len; - } - - /* This reserves IO space but doesn't actually enable it */ - if (pcmcia_request_io(link, &link->io) != 0) - goto next_entry; - } - - - /* If we got this far, we're cool! */ - - break; - - next_entry: - pcmcia_disable_device(link); - last_ret = pcmcia_get_next_tuple(link, &tuple); - if (last_ret == CS_NO_MORE_ITEMS) { + last_ret = pcmcia_loop_config(link, orinoco_cs_config_check, cfg_mem); + if (last_ret) { + if (!ignore_cis_vcc) printk(KERN_ERR PFX "GetNextTuple(): No matching " "CIS configuration. Maybe you need the " "ignore_cis_vcc=1 parameter.\n"); - goto cs_failed; - } + cs_error(link, RequestIO, last_ret); + goto failed; } /* @@ -334,7 +327,7 @@ orinoco_cs_config(struct pcmcia_device *link) "0x%04x-0x%04x\n", dev->name, dev->dev.parent->bus_id, link->irq.AssignedIRQ, link->io.BasePort1, link->io.BasePort1 + link->io.NumPorts1 - 1); - + kfree(cfg_mem); return 0; cs_failed: @@ -342,6 +335,7 @@ orinoco_cs_config(struct pcmcia_device *link) failed: orinoco_cs_release(link); + kfree(cfg_mem); return -ENODEV; } /* orinoco_cs_config */ diff --git a/drivers/net/wireless/spectrum_cs.c b/drivers/net/wireless/spectrum_cs.c index 98df9bc7836a..8e1951cfc152 100644 --- a/drivers/net/wireless/spectrum_cs.c +++ b/drivers/net/wireless/spectrum_cs.c @@ -633,23 +633,96 @@ static void spectrum_cs_detach(struct pcmcia_device *link) * device available to the system. */ +struct spectrum_cs_config_data { + cistpl_cftable_entry_t dflt; + config_info_t conf; +}; + +static int spectrum_cs_config_check(struct pcmcia_device *p_dev, + cistpl_cftable_entry_t *cfg, + void *priv_data) +{ + struct spectrum_cs_config_data *cfg_mem = priv_data; + + if (cfg->flags & CISTPL_CFTABLE_DEFAULT) + cfg_mem->dflt = *cfg; + if (cfg->index == 0) + goto next_entry; + p_dev->conf.ConfigIndex = cfg->index; + + /* Use power settings for Vcc and Vpp if present */ + /* Note that the CIS values need to be rescaled */ + if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) { + if (cfg_mem->conf.Vcc != cfg->vcc.param[CISTPL_POWER_VNOM] / 10000) { + DEBUG(2, "spectrum_cs_config: Vcc mismatch (cfg_mem->conf.Vcc = %d, CIS = %d)\n", cfg_mem->conf.Vcc, cfg->vcc.param[CISTPL_POWER_VNOM] / 10000); + if (!ignore_cis_vcc) + goto next_entry; + } + } else if (cfg_mem->dflt.vcc.present & (1 << CISTPL_POWER_VNOM)) { + if (cfg_mem->conf.Vcc != cfg_mem->dflt.vcc.param[CISTPL_POWER_VNOM] / 10000) { + DEBUG(2, "spectrum_cs_config: Vcc mismatch (cfg_mem->conf.Vcc = %d, CIS = %d)\n", cfg_mem->conf.Vcc, cfg_mem->dflt.vcc.param[CISTPL_POWER_VNOM] / 10000); + if (!ignore_cis_vcc) + goto next_entry; + } + } + + if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM)) + p_dev->conf.Vpp = + cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000; + else if (cfg_mem->dflt.vpp1.present & (1 << CISTPL_POWER_VNOM)) + p_dev->conf.Vpp = + cfg_mem->dflt.vpp1.param[CISTPL_POWER_VNOM] / 10000; + + /* Do we need to allocate an interrupt? */ + p_dev->conf.Attributes |= CONF_ENABLE_IRQ; + + /* IO window settings */ + p_dev->io.NumPorts1 = p_dev->io.NumPorts2 = 0; + if ((cfg->io.nwin > 0) || (cfg_mem->dflt.io.nwin > 0)) { + cistpl_io_t *io = (cfg->io.nwin) ? &cfg->io : &cfg_mem->dflt.io; + p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO; + if (!(io->flags & CISTPL_IO_8BIT)) + p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_16; + if (!(io->flags & CISTPL_IO_16BIT)) + p_dev->io.Attributes1 = IO_DATA_PATH_WIDTH_8; + p_dev->io.IOAddrLines = io->flags & CISTPL_IO_LINES_MASK; + p_dev->io.BasePort1 = io->win[0].base; + p_dev->io.NumPorts1 = io->win[0].len; + if (io->nwin > 1) { + p_dev->io.Attributes2 = p_dev->io.Attributes1; + p_dev->io.BasePort2 = io->win[1].base; + p_dev->io.NumPorts2 = io->win[1].len; + } + + /* This reserves IO space but doesn't actually enable it */ + if (pcmcia_request_io(p_dev, &p_dev->io) != 0) + goto next_entry; + } + return 0; + +next_entry: + pcmcia_disable_device(p_dev); + return -ENODEV; +}; + static int spectrum_cs_config(struct pcmcia_device *link) { + struct spectrum_cs_config_data *cfg_mem; struct net_device *dev = link->priv; struct orinoco_private *priv = netdev_priv(dev); struct orinoco_pccard *card = priv->card; hermes_t *hw = &priv->hw; int last_fn, last_ret; - u_char buf[64]; - config_info_t conf; - tuple_t tuple; - cisparse_t parse; void __iomem *mem; + cfg_mem = kzalloc(sizeof(struct spectrum_cs_config_data), GFP_KERNEL); + if (!cfg_mem) + return -ENOMEM; + /* Look up the current Vcc */ CS_CHECK(GetConfigurationInfo, - pcmcia_get_configuration_info(link, &conf)); + pcmcia_get_configuration_info(link, &cfg_mem->conf)); /* * In this loop, we scan the CIS for configuration table @@ -665,94 +738,14 @@ spectrum_cs_config(struct pcmcia_device *link) * and most client drivers will only use the CIS to fill in * implementation-defined details. */ - tuple.DesiredTuple = CISTPL_CFTABLE_ENTRY; - tuple.Attributes = 0; - tuple.TupleData = buf; - tuple.TupleDataMax = sizeof(buf); - tuple.TupleOffset = 0; - CS_CHECK(GetFirstTuple, pcmcia_get_first_tuple(link, &tuple)); - while (1) { - cistpl_cftable_entry_t *cfg = &(parse.cftable_entry); - cistpl_cftable_entry_t dflt = { .index = 0 }; - - if ( (pcmcia_get_tuple_data(link, &tuple) != 0) - || (pcmcia_parse_tuple(link, &tuple, &parse) != 0)) - goto next_entry; - - if (cfg->flags & CISTPL_CFTABLE_DEFAULT) - dflt = *cfg; - if (cfg->index == 0) - goto next_entry; - link->conf.ConfigIndex = cfg->index; - - /* Use power settings for Vcc and Vpp if present */ - /* Note that the CIS values need to be rescaled */ - if (cfg->vcc.present & (1 << CISTPL_POWER_VNOM)) { - if (conf.Vcc != cfg->vcc.param[CISTPL_POWER_VNOM] / 10000) { - DEBUG(2, "spectrum_cs_config: Vcc mismatch (conf.Vcc = %d, CIS = %d)\n", conf.Vcc, cfg->vcc.param[CISTPL_POWER_VNOM] / 10000); - if (!ignore_cis_vcc) - goto next_entry; - } - } else if (dflt.vcc.present & (1 << CISTPL_POWER_VNOM)) { - if (conf.Vcc != dflt.vcc.param[CISTPL_POWER_VNOM] / 10000) { - DEBUG(2, "spectrum_cs_config: Vcc mismatch (conf.Vcc = %d, CIS = %d)\n", conf.Vcc, dflt.vcc.param[CISTPL_POWER_VNOM] / 10000); - if(!ignore_cis_vcc) - goto next_entry; - } - } - - if (cfg->vpp1.present & (1 << CISTPL_POWER_VNOM)) - link->conf.Vpp = - cfg->vpp1.param[CISTPL_POWER_VNOM] / 10000; - else if (dflt.vpp1.present & (1 << CISTPL_POWER_VNOM)) - link->conf.Vpp = - dflt.vpp1.param[CISTPL_POWER_VNOM] / 10000; - - /* Do we need to allocate an interrupt? */ - link->conf.Attributes |= CONF_ENABLE_IRQ; - - /* IO window settings */ - link->io.NumPorts1 = link->io.NumPorts2 = 0; - if ((cfg->io.nwin > 0) || (dflt.io.nwin > 0)) { - cistpl_io_t *io = - (cfg->io.nwin) ? &cfg->io : &dflt.io; - link->io.Attributes1 = IO_DATA_PATH_WIDTH_AUTO; - if (!(io->flags & CISTPL_IO_8BIT)) - link->io.Attributes1 = - IO_DATA_PATH_WIDTH_16; - if (!(io->flags & CISTPL_IO_16BIT)) - link->io.Attributes1 = - IO_DATA_PATH_WIDTH_8; - link->io.IOAddrLines = - io->flags & CISTPL_IO_LINES_MASK; - link->io.BasePort1 = io->win[0].base; - link->io.NumPorts1 = io->win[0].len; - if (io->nwin > 1) { - link->io.Attributes2 = - link->io.Attributes1; - link->io.BasePort2 = io->win[1].base; - link->io.NumPorts2 = io->win[1].len; - } - - /* This reserves IO space but doesn't actually enable it */ - if (pcmcia_request_io(link, &link->io) != 0) - goto next_entry; - } - - - /* If we got this far, we're cool! */ - - break; - - next_entry: - pcmcia_disable_device(link); - last_ret = pcmcia_get_next_tuple(link, &tuple); - if (last_ret == CS_NO_MORE_ITEMS) { + last_ret = pcmcia_loop_config(link, spectrum_cs_config_check, cfg_mem); + if (last_ret) { + if (!ignore_cis_vcc) printk(KERN_ERR PFX "GetNextTuple(): No matching " "CIS configuration. Maybe you need the " "ignore_cis_vcc=1 parameter.\n"); - goto cs_failed; - } + cs_error(link, RequestIO, last_ret); + goto failed; } /* @@ -809,6 +802,7 @@ spectrum_cs_config(struct pcmcia_device *link) link->irq.AssignedIRQ, link->io.BasePort1, link->io.BasePort1 + link->io.NumPorts1 - 1); + kfree(cfg_mem); return 0; cs_failed: @@ -816,6 +810,7 @@ spectrum_cs_config(struct pcmcia_device *link) failed: spectrum_cs_release(link); + kfree(cfg_mem); return -ENODEV; } /* spectrum_cs_config */ -- cgit v1.2.1