From 7111ebc97ed53a32314011c85a6f235f0dab8ae8 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Tue, 14 Dec 2010 13:24:55 -0800 Subject: xhci: Resume bus on any port status change. The original code that resumed the USB bus on a port status change would only do so when there was a device connected to the port. If a device was just disconnected, the event would be queued for khubd, but khubd wouldn't run. That would leave the connect status change (CSC) bit set. If a USB device was plugged into that same port, the xHCI host controller would set the current connect status (CCS) bit. But since the CSC bit was already set, it would not generate an interrupt for a port status change event. That would mean the user could "Safely Remove" a device, have the bus suspend, disconnect the device, re-plug it in, and then the device would never be enumerated. Plugging in a different device on another port would cause the bus to resume, and khubd would notice the re-connected device. Running lsusb would also resume the bus, leading users to report the problem "went away" when using diagnostic tools. The solution is to resume the bus when a port status change event is received, regardless of the port status. Thank you very much to Maddog for helping me track down this Heisenbug. This patch should be queued for the 2.6.37 stable tree. Signed-off-by: Sarah Sharp Reported-by: Jon 'maddog' Hall Tested-by: Andiry Xu Cc: stable@kernel.org --- drivers/usb/host/xhci-ring.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index df558f6f84e3..62c70c230e83 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -1188,7 +1188,7 @@ static void handle_port_status(struct xhci_hcd *xhci, addr = &xhci->op_regs->port_status_base + NUM_PORT_REGS * (port_id - 1); temp = xhci_readl(xhci, addr); - if ((temp & PORT_CONNECT) && (hcd->state == HC_STATE_SUSPENDED)) { + if (hcd->state == HC_STATE_SUSPENDED) { xhci_dbg(xhci, "resume root hub\n"); usb_hcd_resume_root_hub(hcd); } -- cgit v1.2.1 From 0029227f1bc30b6c809ae751f9e7af6cef900997 Mon Sep 17 00:00:00 2001 From: Andiry Xu Date: Mon, 27 Dec 2010 17:39:02 +0800 Subject: xHCI: synchronize irq in xhci_suspend() Synchronize the interrupts instead of free them in xhci_suspend(). This will prevent a double free when the host is suspended and then the card removed. Set the flag hcd->msix_enabled when using MSI-X, and check the flag in suspend_common(). MSI-X synchronization will be handled by xhci_suspend(), and MSI/INTx will be synchronized in suspend_common(). This patch should be queued for the 2.6.37 stable tree. Reported-by: Matthew Garrett Signed-off-by: Andiry Xu Signed-off-by: Sarah Sharp Cc: stable@kernel.org --- drivers/usb/host/xhci.c | 46 +++++++++++++++------------------------------- 1 file changed, 15 insertions(+), 31 deletions(-) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index 45e4a3108cc3..d48edfa5043a 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -226,7 +226,8 @@ static int xhci_setup_msi(struct xhci_hcd *xhci) static int xhci_setup_msix(struct xhci_hcd *xhci) { int i, ret = 0; - struct pci_dev *pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller); + struct usb_hcd *hcd = xhci_to_hcd(xhci); + struct pci_dev *pdev = to_pci_dev(hcd->self.controller); /* * calculate number of msi-x vectors supported. @@ -265,6 +266,7 @@ static int xhci_setup_msix(struct xhci_hcd *xhci) goto disable_msix; } + hcd->msix_enabled = 1; return ret; disable_msix: @@ -280,7 +282,8 @@ free_entries: /* Free any IRQs and disable MSI-X */ static void xhci_cleanup_msix(struct xhci_hcd *xhci) { - struct pci_dev *pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller); + struct usb_hcd *hcd = xhci_to_hcd(xhci); + struct pci_dev *pdev = to_pci_dev(hcd->self.controller); xhci_free_irq(xhci); @@ -292,6 +295,7 @@ static void xhci_cleanup_msix(struct xhci_hcd *xhci) pci_disable_msi(pdev); } + hcd->msix_enabled = 0; return; } @@ -647,6 +651,7 @@ int xhci_suspend(struct xhci_hcd *xhci) int rc = 0; struct usb_hcd *hcd = xhci_to_hcd(xhci); u32 command; + int i; spin_lock_irq(&xhci->lock); clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); @@ -677,10 +682,15 @@ int xhci_suspend(struct xhci_hcd *xhci) spin_unlock_irq(&xhci->lock); return -ETIMEDOUT; } - /* step 5: remove core well power */ - xhci_cleanup_msix(xhci); spin_unlock_irq(&xhci->lock); + /* step 5: remove core well power */ + /* synchronize irq when using MSI-X */ + if (xhci->msix_entries) { + for (i = 0; i < xhci->msix_count; i++) + synchronize_irq(xhci->msix_entries[i].vector); + } + return rc; } @@ -694,7 +704,6 @@ int xhci_resume(struct xhci_hcd *xhci, bool hibernated) { u32 command, temp = 0; struct usb_hcd *hcd = xhci_to_hcd(xhci); - struct pci_dev *pdev = to_pci_dev(hcd->self.controller); int old_state, retval; old_state = hcd->state; @@ -729,9 +738,8 @@ int xhci_resume(struct xhci_hcd *xhci, bool hibernated) xhci_dbg(xhci, "Stop HCD\n"); xhci_halt(xhci); xhci_reset(xhci); - if (hibernated) - xhci_cleanup_msix(xhci); spin_unlock_irq(&xhci->lock); + xhci_cleanup_msix(xhci); #ifdef CONFIG_USB_XHCI_HCD_DEBUGGING /* Tell the event ring poll function not to reschedule */ @@ -765,30 +773,6 @@ int xhci_resume(struct xhci_hcd *xhci, bool hibernated) return retval; } - spin_unlock_irq(&xhci->lock); - /* Re-setup MSI-X */ - if (hcd->irq) - free_irq(hcd->irq, hcd); - hcd->irq = -1; - - retval = xhci_setup_msix(xhci); - if (retval) - /* fall back to msi*/ - retval = xhci_setup_msi(xhci); - - if (retval) { - /* fall back to legacy interrupt*/ - retval = request_irq(pdev->irq, &usb_hcd_irq, IRQF_SHARED, - hcd->irq_descr, hcd); - if (retval) { - xhci_err(xhci, "request interrupt %d failed\n", - pdev->irq); - return retval; - } - hcd->irq = pdev->irq; - } - - spin_lock_irq(&xhci->lock); /* step 4: set Run/Stop bit */ command = xhci_readl(xhci, &xhci->op_regs->command); command |= CMD_RUN; -- cgit v1.2.1 From 40a9fb17f32dbe54de3d636142a59288544deed7 Mon Sep 17 00:00:00 2001 From: Zhang Rui Date: Fri, 17 Dec 2010 13:17:04 -0800 Subject: xhci: Do not run xhci_cleanup_msix with irq disabled when unloading xhci_hcd, I got: [ 134.856813] xhci_hcd 0000:02:00.0: remove, state 4 [ 134.858140] usb usb3: USB disconnect, address 1 [ 134.874956] xhci_hcd 0000:02:00.0: Host controller not halted, aborting reset. [ 134.876351] BUG: sleeping function called from invalid context at kernel/mutex.c:85 [ 134.877657] in_atomic(): 0, irqs_disabled(): 1, pid: 1451, name: modprobe [ 134.878975] Pid: 1451, comm: modprobe Not tainted 2.6.37-rc5+ #162 [ 134.880298] Call Trace: [ 134.881602] [] __might_sleep+0xeb/0xf0 [ 134.882921] [] mutex_lock+0x24/0x50 [ 134.884229] [] free_desc+0x2e/0x5f [ 134.885538] [] irq_free_descs+0x3b/0x71 [ 134.886853] [] free_irq_at+0x31/0x36 [ 134.888167] [] destroy_irq+0x69/0x71 [ 134.889486] [] native_teardown_msi_irq+0xe/0x10 [ 134.890820] [] default_teardown_msi_irqs+0x57/0x80 [ 134.892158] [] free_msi_irqs+0x8b/0xe9 [ 134.893504] [] pci_disable_msix+0x35/0x39 [ 134.894844] [] xhci_cleanup_msix+0x31/0x51 [xhci_hcd] [ 134.896186] [] xhci_stop+0x3a/0x80 [xhci_hcd] [ 134.897521] [] usb_remove_hcd+0xfd/0x14a [ 134.898859] [] usb_hcd_pci_remove+0x5c/0xc6 [ 134.900193] [] pci_device_remove+0x3f/0x91 [ 134.901535] [] __device_release_driver+0x83/0xd9 [ 134.902899] [] driver_detach+0x86/0xad [ 134.904222] [] bus_remove_driver+0xb2/0xd8 [ 134.905540] [] driver_unregister+0x6c/0x74 [ 134.906839] [] pci_unregister_driver+0x44/0x89 [ 134.908121] [] xhci_unregister_pci+0x15/0x17 [xhci_hcd] [ 134.909396] [] xhci_hcd_cleanup+0xe/0x10 [xhci_hcd] [ 134.910652] [] sys_delete_module+0x1ca/0x23b [ 134.911882] [] ? path_put+0x22/0x26 [ 134.913104] [] ? audit_syscall_entry+0x2c/0x148 [ 134.914333] [] system_call_fastpath+0x16/0x1b [ 134.915658] xhci_hcd 0000:02:00.0: USB bus 3 deregistered [ 134.916465] xhci_hcd 0000:02:00.0: PCI INT A disabled and the same issue when xhci_suspend is invoked. (Note from Sarah: That's fixed by Andiry's patch before this, by synchronizing the irqs rather than freeing them on suspend.) Do not run xhci_cleanup_msix with irq disabled. This patch should be queued for the 2.6.37 stable tree. Signed-off-by: Zhang Rui Signed-off-by: Sarah Sharp Cc: stable@kernel.org --- drivers/usb/host/xhci.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index d48edfa5043a..b2c56d15fb42 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -512,9 +512,10 @@ void xhci_stop(struct usb_hcd *hcd) spin_lock_irq(&xhci->lock); xhci_halt(xhci); xhci_reset(xhci); - xhci_cleanup_msix(xhci); spin_unlock_irq(&xhci->lock); + xhci_cleanup_msix(xhci); + #ifdef CONFIG_USB_XHCI_HCD_DEBUGGING /* Tell the event ring poll function not to reschedule */ xhci->zombie = 1; @@ -548,9 +549,10 @@ void xhci_shutdown(struct usb_hcd *hcd) spin_lock_irq(&xhci->lock); xhci_halt(xhci); - xhci_cleanup_msix(xhci); spin_unlock_irq(&xhci->lock); + xhci_cleanup_msix(xhci); + xhci_dbg(xhci, "xhci_shutdown completed - status = %x\n", xhci_readl(xhci, &xhci->op_regs->status)); } -- cgit v1.2.1 From a6d940dd759bf240d28624198660ed34582a327b Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Tue, 28 Dec 2010 13:08:42 -0800 Subject: xhci: Use GFP_NOIO during device reset. When xhci_discover_or_reset_device() is called after a host controller power loss, the virtual device may need to be reallocated. Make sure xhci_alloc_dev() uses GFP_NOIO. This avoid causing a deadlock by allowing the kernel to flush pending I/O while reallocating memory for a virtual device for a USB mass storage device that's holding the backing store for dirty memory buffers. This patch should be queued for the 2.6.37 stable tree. Signed-off-by: Sarah Sharp Cc: stable@kernel.org --- drivers/usb/host/xhci.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index b2c56d15fb42..34cf4e165877 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -2431,8 +2431,12 @@ int xhci_alloc_dev(struct usb_hcd *hcd, struct usb_device *udev) xhci_err(xhci, "Error while assigning device slot ID\n"); return 0; } - /* xhci_alloc_virt_device() does not touch rings; no need to lock */ - if (!xhci_alloc_virt_device(xhci, xhci->slot_id, udev, GFP_KERNEL)) { + /* xhci_alloc_virt_device() does not touch rings; no need to lock. + * Use GFP_NOIO, since this function can be called from + * xhci_discover_or_reset_device(), which may be called as part of + * mass storage driver error handling. + */ + if (!xhci_alloc_virt_device(xhci, xhci->slot_id, udev, GFP_NOIO)) { /* Disable slot, if we can do it without mem alloc */ xhci_warn(xhci, "Could not allocate xHCI USB device data structures\n"); spin_lock_irqsave(&xhci->lock, flags); -- cgit v1.2.1 From 47cbf6925cd0ef8af4b8165b43a60b5f37c36d8a Mon Sep 17 00:00:00 2001 From: Andiry Xu Date: Mon, 20 Dec 2010 14:49:48 +0800 Subject: xHCI: fix queue_trb in isoc transfer Fix the more_trbs_coming field of queue_trb() in isoc transfer. Signed-off-by: Andiry Xu Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci-ring.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 62c70c230e83..55dc15675068 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -2900,6 +2900,7 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags, int running_total, trb_buff_len, td_len, td_remain_len, ret; u64 start_addr, addr; int i, j; + bool more_trbs_coming; ep_ring = xhci->devs[slot_id]->eps[ep_index].ring; @@ -2965,9 +2966,11 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags, */ if (j < trbs_per_td - 1) { field |= TRB_CHAIN; + more_trbs_coming = true; } else { td->last_trb = ep_ring->enqueue; field |= TRB_IOC; + more_trbs_coming = false; } /* Calculate TRB length */ @@ -2980,7 +2983,7 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags, length_field = TRB_LEN(trb_buff_len) | remainder | TRB_INTR_TARGET(0); - queue_trb(xhci, ep_ring, false, false, + queue_trb(xhci, ep_ring, false, more_trbs_coming, lower_32_bits(addr), upper_32_bits(addr), length_field, -- cgit v1.2.1 From e1eab2e00015bfe48388920ff287efdbefb6af24 Mon Sep 17 00:00:00 2001 From: Andiry Xu Date: Tue, 4 Jan 2011 16:30:39 -0800 Subject: xHCI: remove redundant parameter in giveback_first_trb() Parameter *td is not used in giveback_first_trb(). Remove it. Signed-off-by: Andiry Xu Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci-ring.c | 14 ++++++-------- 1 file changed, 6 insertions(+), 8 deletions(-) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 55dc15675068..59f81b560483 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -2414,7 +2414,7 @@ static void check_trb_math(struct urb *urb, int num_trbs, int running_total) static void giveback_first_trb(struct xhci_hcd *xhci, int slot_id, unsigned int ep_index, unsigned int stream_id, int start_cycle, - struct xhci_generic_trb *start_trb, struct xhci_td *td) + struct xhci_generic_trb *start_trb) { /* * Pass all the TRBs to the hardware at once and make sure this write @@ -2625,7 +2625,7 @@ static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags, check_trb_math(urb, num_trbs, running_total); giveback_first_trb(xhci, slot_id, ep_index, urb->stream_id, - start_cycle, start_trb, td); + start_cycle, start_trb); return 0; } @@ -2757,7 +2757,7 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, check_trb_math(urb, num_trbs, running_total); giveback_first_trb(xhci, slot_id, ep_index, urb->stream_id, - start_cycle, start_trb, td); + start_cycle, start_trb); return 0; } @@ -2859,7 +2859,7 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags, field | TRB_IOC | TRB_TYPE(TRB_STATUS) | ep_ring->cycle_state); giveback_first_trb(xhci, slot_id, ep_index, 0, - start_cycle, start_trb, td); + start_cycle, start_trb); return 0; } @@ -3006,10 +3006,8 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags, } } - wmb(); - start_trb->field[3] |= start_cycle; - - xhci_ring_ep_doorbell(xhci, slot_id, ep_index, urb->stream_id); + giveback_first_trb(xhci, slot_id, ep_index, urb->stream_id, + start_cycle, start_trb); return 0; } -- cgit v1.2.1 From 50f7b52a83a893929edf87a89ebc081ff26a7b91 Mon Sep 17 00:00:00 2001 From: Andiry Xu Date: Mon, 20 Dec 2010 15:09:34 +0800 Subject: xHCI: fix cycle bit set in giveback_first_trb() giveback_first_trb() controls the cycle bit set of the start_trb, to ensure that the start_trb is written last and the host controller will receive a whole td at a time. However, if the ring is wrapped and cycle bit is toggled to zero, then giveback_first_trb() will be of no effect. In this case, set the cycle bit of start_trb to 1 at the beginning and clear it in giveback_first_trb(). Signed-off-by: Andiry Xu Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci-ring.c | 28 +++++++++++++++++++++------- 1 file changed, 21 insertions(+), 7 deletions(-) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 59f81b560483..1ee6de92193a 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -2421,7 +2421,10 @@ static void giveback_first_trb(struct xhci_hcd *xhci, int slot_id, * isn't reordered. */ wmb(); - start_trb->field[3] |= start_cycle; + if (start_cycle) + start_trb->field[3] |= start_cycle; + else + start_trb->field[3] &= ~0x1; xhci_ring_ep_doorbell(xhci, slot_id, ep_index, stream_id); } @@ -2551,9 +2554,11 @@ static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags, u32 remainder = 0; /* Don't change the cycle bit of the first TRB until later */ - if (first_trb) + if (first_trb) { first_trb = false; - else + if (start_cycle == 0) + field |= 0x1; + } else field |= ep_ring->cycle_state; /* Chain all the TRBs together; clear the chain bit in the last @@ -2711,9 +2716,11 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, field = 0; /* Don't change the cycle bit of the first TRB until later */ - if (first_trb) + if (first_trb) { first_trb = false; - else + if (start_cycle == 0) + field |= 0x1; + } else field |= ep_ring->cycle_state; /* Chain all the TRBs together; clear the chain bit in the last @@ -2818,13 +2825,17 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags, /* Queue setup TRB - see section 6.4.1.2.1 */ /* FIXME better way to translate setup_packet into two u32 fields? */ setup = (struct usb_ctrlrequest *) urb->setup_packet; + field = 0; + field |= TRB_IDT | TRB_TYPE(TRB_SETUP); + if (start_cycle == 0) + field |= 0x1; queue_trb(xhci, ep_ring, false, true, /* FIXME endianness is probably going to bite my ass here. */ setup->bRequestType | setup->bRequest << 8 | setup->wValue << 16, setup->wIndex | setup->wLength << 16, TRB_LEN(8) | TRB_INTR_TARGET(0), /* Immediate data in pointer */ - TRB_IDT | TRB_TYPE(TRB_SETUP)); + field); /* If there's data, queue data TRBs */ field = 0; @@ -2951,7 +2962,10 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags, field |= TRB_TYPE(TRB_ISOC); /* Assume URB_ISO_ASAP is set */ field |= TRB_SIA; - if (i > 0) + if (i == 0) { + if (start_cycle == 0) + field |= 0x1; + } else field |= ep_ring->cycle_state; first_trb = false; } else { -- cgit v1.2.1 From f2c565e223af39ed38be5c84b1a37b591b22db83 Mon Sep 17 00:00:00 2001 From: Andiry Xu Date: Mon, 20 Dec 2010 17:12:24 +0800 Subject: xHCI: replace dev_dbg() with xhci_dbg() dev_dbg() is used to print ordinary transfer messages in xhci-ring.c. System log messages will be flushed if CONFIG_USB_DEBUG is set. Replace the dev_dbg() with xhci_dbg(). Signed-off-by: Andiry Xu Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci-ring.c | 11 ++++++----- 1 file changed, 6 insertions(+), 5 deletions(-) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 1ee6de92193a..e38f7ece0a67 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -1710,8 +1710,7 @@ static int process_bulk_intr_td(struct xhci_hcd *xhci, struct xhci_td *td, /* Others already handled above */ break; } - dev_dbg(&td->urb->dev->dev, - "ep %#x - asked for %d bytes, " + xhci_dbg(xhci, "ep %#x - asked for %d bytes, " "%d bytes untransferred\n", td->urb->ep->desc.bEndpointAddress, td->urb->transfer_buffer_length, @@ -2389,7 +2388,8 @@ static unsigned int count_sg_trbs_needed(struct xhci_hcd *xhci, struct urb *urb) } xhci_dbg(xhci, "\n"); if (!in_interrupt()) - dev_dbg(&urb->dev->dev, "ep %#x - urb len = %d, sglist used, num_trbs = %d\n", + xhci_dbg(xhci, "ep %#x - urb len = %d, sglist used, " + "num_trbs = %d\n", urb->ep->desc.bEndpointAddress, urb->transfer_buffer_length, num_trbs); @@ -2676,7 +2676,8 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, /* FIXME: this doesn't deal with URB_ZERO_PACKET - need one more */ if (!in_interrupt()) - dev_dbg(&urb->dev->dev, "ep %#x - urb len = %#x (%d), addr = %#llx, num_trbs = %d\n", + xhci_dbg(xhci, "ep %#x - urb len = %#x (%d), " + "addr = %#llx, num_trbs = %d\n", urb->ep->desc.bEndpointAddress, urb->transfer_buffer_length, urb->transfer_buffer_length, @@ -2922,7 +2923,7 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags, } if (!in_interrupt()) - dev_dbg(&urb->dev->dev, "ep %#x - urb len = %#x (%d)," + xhci_dbg(xhci, "ep %#x - urb len = %#x (%d)," " addr = %#llx, num_tds = %d\n", urb->ep->desc.bEndpointAddress, urb->transfer_buffer_length, -- cgit v1.2.1 From 7961acd7327fe48e55abef277630abdbb3f2081a Mon Sep 17 00:00:00 2001 From: Andiry Xu Date: Mon, 20 Dec 2010 17:14:20 +0800 Subject: xHCI: fix printk_ratelimit() usage printk_ratelimit() is misused in xhci-ring.c. Signed-off-by: Andiry Xu Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci-ring.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index e38f7ece0a67..2116c0f64952 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -2452,7 +2452,7 @@ int xhci_queue_intr_tx(struct xhci_hcd *xhci, gfp_t mem_flags, * to set the polling interval (once the API is added). */ if (xhci_interval != ep_interval) { - if (!printk_ratelimit()) + if (printk_ratelimit()) dev_dbg(&urb->dev->dev, "Driver uses different interval" " (%d microframe%s) than xHCI " "(%d microframe%s)\n", @@ -3080,7 +3080,7 @@ int xhci_queue_isoc_tx_prepare(struct xhci_hcd *xhci, gfp_t mem_flags, * to set the polling interval (once the API is added). */ if (xhci_interval != ep_interval) { - if (!printk_ratelimit()) + if (printk_ratelimit()) dev_dbg(&urb->dev->dev, "Driver uses different interval" " (%d microframe%s) than xHCI " "(%d microframe%s)\n", -- cgit v1.2.1 From 50d64676d132a8a72a1a1657d7b3e6efa53da1ac Mon Sep 17 00:00:00 2001 From: Matthew Wilcox Date: Wed, 15 Dec 2010 14:18:11 -0500 Subject: xhci: Remove more doorbell-related reads The unused space in the doorbell is now marked as RsvdZ, not RsvdP, so we can avoid reading the doorbell before writing it. Update the doorbell-related defines to produce the entire doorbell value from a single macro. Document the doorbell format in a comment. Signed-off-by: Matthew Wilcox Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci-ring.c | 27 +++++++++++---------------- drivers/usb/host/xhci.h | 16 ++++++---------- 2 files changed, 17 insertions(+), 26 deletions(-) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 2116c0f64952..3e8211c1ce5a 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -308,11 +308,8 @@ static int room_on_ring(struct xhci_hcd *xhci, struct xhci_ring *ring, /* Ring the host controller doorbell after placing a command on the ring */ void xhci_ring_cmd_db(struct xhci_hcd *xhci) { - u32 temp; - xhci_dbg(xhci, "// Ding dong!\n"); - temp = xhci_readl(xhci, &xhci->dba->doorbell[0]) & DB_MASK; - xhci_writel(xhci, temp | DB_TARGET_HOST, &xhci->dba->doorbell[0]); + xhci_writel(xhci, DB_VALUE_HOST, &xhci->dba->doorbell[0]); /* Flush PCI posted writes */ xhci_readl(xhci, &xhci->dba->doorbell[0]); } @@ -322,26 +319,24 @@ void xhci_ring_ep_doorbell(struct xhci_hcd *xhci, unsigned int ep_index, unsigned int stream_id) { - struct xhci_virt_ep *ep; - unsigned int ep_state; - u32 field; __u32 __iomem *db_addr = &xhci->dba->doorbell[slot_id]; + struct xhci_virt_ep *ep = &xhci->devs[slot_id]->eps[ep_index]; + unsigned int ep_state = ep->ep_state; - ep = &xhci->devs[slot_id]->eps[ep_index]; - ep_state = ep->ep_state; /* Don't ring the doorbell for this endpoint if there are pending - * cancellations because the we don't want to interrupt processing. + * cancellations because we don't want to interrupt processing. * We don't want to restart any stream rings if there's a set dequeue * pointer command pending because the device can choose to start any * stream once the endpoint is on the HW schedule. * FIXME - check all the stream rings for pending cancellations. */ - if (!(ep_state & EP_HALT_PENDING) && !(ep_state & SET_DEQ_PENDING) - && !(ep_state & EP_HALTED)) { - field = xhci_readl(xhci, db_addr) & DB_MASK; - field |= EPI_TO_DB(ep_index) | STREAM_ID_TO_DB(stream_id); - xhci_writel(xhci, field, db_addr); - } + if ((ep_state & EP_HALT_PENDING) || (ep_state & SET_DEQ_PENDING) || + (ep_state & EP_HALTED)) + return; + xhci_writel(xhci, DB_VALUE(ep_index, stream_id), db_addr); + /* The CPU has better things to do at this point than wait for a + * write-posting flush. It'll get there soon enough. + */ } /* Ring the doorbell for any rings with pending URBs */ diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 170c367112d2..7f236fd22015 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -436,22 +436,18 @@ struct xhci_run_regs { /** * struct doorbell_array * + * Bits 0 - 7: Endpoint target + * Bits 8 - 15: RsvdZ + * Bits 16 - 31: Stream ID + * * Section 5.6 */ struct xhci_doorbell_array { u32 doorbell[256]; }; -#define DB_TARGET_MASK 0xFFFFFF00 -#define DB_STREAM_ID_MASK 0x0000FFFF -#define DB_TARGET_HOST 0x0 -#define DB_STREAM_ID_HOST 0x0 -#define DB_MASK (0xff << 8) - -/* Endpoint Target - bits 0:7 */ -#define EPI_TO_DB(p) (((p) + 1) & 0xff) -#define STREAM_ID_TO_DB(p) (((p) & 0xffff) << 16) - +#define DB_VALUE(ep, stream) ((((ep) + 1) & 0xff) | ((stream) << 16)) +#define DB_VALUE_HOST 0x00000000 /** * struct xhci_protocol_caps -- cgit v1.2.1 From baab93afc2844b68d57b0dcca5e1d34c5d7cf411 Mon Sep 17 00:00:00 2001 From: Alex He Date: Tue, 21 Dec 2010 17:45:46 +0800 Subject: USB: EHCI: ASPM quirk of ISOC on AMD Hudson AMD Hudson also needs the same ASPM quirk as SB800 Signed-off-by: Alex He Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-pci.c | 33 ++++++++++++++++++++------------- 1 file changed, 20 insertions(+), 13 deletions(-) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c index 76179c39c0e3..bed07d4aab06 100644 --- a/drivers/usb/host/ehci-pci.c +++ b/drivers/usb/host/ehci-pci.c @@ -44,28 +44,35 @@ static int ehci_pci_reinit(struct ehci_hcd *ehci, struct pci_dev *pdev) return 0; } -static int ehci_quirk_amd_SB800(struct ehci_hcd *ehci) +static int ehci_quirk_amd_hudson(struct ehci_hcd *ehci) { struct pci_dev *amd_smbus_dev; u8 rev = 0; amd_smbus_dev = pci_get_device(PCI_VENDOR_ID_ATI, 0x4385, NULL); - if (!amd_smbus_dev) - return 0; - - pci_read_config_byte(amd_smbus_dev, PCI_REVISION_ID, &rev); - if (rev < 0x40) { - pci_dev_put(amd_smbus_dev); - amd_smbus_dev = NULL; - return 0; + if (amd_smbus_dev) { + pci_read_config_byte(amd_smbus_dev, PCI_REVISION_ID, &rev); + if (rev < 0x40) { + pci_dev_put(amd_smbus_dev); + amd_smbus_dev = NULL; + return 0; + } + } else { + amd_smbus_dev = pci_get_device(PCI_VENDOR_ID_AMD, 0x780b, NULL); + if (!amd_smbus_dev) + return 0; + pci_read_config_byte(amd_smbus_dev, PCI_REVISION_ID, &rev); + if (rev < 0x11 || rev > 0x18) { + pci_dev_put(amd_smbus_dev); + amd_smbus_dev = NULL; + return 0; + } } if (!amd_nb_dev) amd_nb_dev = pci_get_device(PCI_VENDOR_ID_AMD, 0x1510, NULL); - if (!amd_nb_dev) - ehci_err(ehci, "QUIRK: unable to get AMD NB device\n"); - ehci_info(ehci, "QUIRK: Enable AMD SB800 L1 fix\n"); + ehci_info(ehci, "QUIRK: Enable exception for AMD Hudson ASPM\n"); pci_dev_put(amd_smbus_dev); amd_smbus_dev = NULL; @@ -131,7 +138,7 @@ static int ehci_pci_setup(struct usb_hcd *hcd) /* cache this readonly data; minimize chip reads */ ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params); - if (ehci_quirk_amd_SB800(ehci)) + if (ehci_quirk_amd_hudson(ehci)) ehci->amd_l1_fix = 1; retval = ehci_halt(ehci); -- cgit v1.2.1 From f75593ceaa08e6d27aec1a5de31cded19e850dd1 Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Thu, 6 Jan 2011 10:17:09 -0500 Subject: USB: EHCI: fix DMA deallocation bug This patch (as1440) fixes a bug in ehci-hcd. ehci->periodic_size is used to compute the size in a dma_alloc_coherent() call, but then it gets changed later on. As a result, the corresponding call to dma_free_coherent() passes a different size from the original allocation. Fix the problem by adjusting ehci->periodic_size before carrying out any of the memory allocations. Signed-off-by: Alan Stern Tested-by: Larry Finger CC: David Brownell CC: Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-hcd.c | 19 ++++++++++++------- 1 file changed, 12 insertions(+), 7 deletions(-) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c index 6fee3cd58efe..74dcf49bd015 100644 --- a/drivers/usb/host/ehci-hcd.c +++ b/drivers/usb/host/ehci-hcd.c @@ -572,6 +572,8 @@ static int ehci_init(struct usb_hcd *hcd) ehci->iaa_watchdog.function = ehci_iaa_watchdog; ehci->iaa_watchdog.data = (unsigned long) ehci; + hcc_params = ehci_readl(ehci, &ehci->caps->hcc_params); + /* * hw default: 1K periodic list heads, one per frame. * periodic_size can shrink by USBCMD update if hcc_params allows. @@ -579,11 +581,20 @@ static int ehci_init(struct usb_hcd *hcd) ehci->periodic_size = DEFAULT_I_TDPS; INIT_LIST_HEAD(&ehci->cached_itd_list); INIT_LIST_HEAD(&ehci->cached_sitd_list); + + if (HCC_PGM_FRAMELISTLEN(hcc_params)) { + /* periodic schedule size can be smaller than default */ + switch (EHCI_TUNE_FLS) { + case 0: ehci->periodic_size = 1024; break; + case 1: ehci->periodic_size = 512; break; + case 2: ehci->periodic_size = 256; break; + default: BUG(); + } + } if ((retval = ehci_mem_init(ehci, GFP_KERNEL)) < 0) return retval; /* controllers may cache some of the periodic schedule ... */ - hcc_params = ehci_readl(ehci, &ehci->caps->hcc_params); if (HCC_ISOC_CACHE(hcc_params)) // full frame cache ehci->i_thresh = 2 + 8; else // N microframes cached @@ -637,12 +648,6 @@ static int ehci_init(struct usb_hcd *hcd) /* periodic schedule size can be smaller than default */ temp &= ~(3 << 2); temp |= (EHCI_TUNE_FLS << 2); - switch (EHCI_TUNE_FLS) { - case 0: ehci->periodic_size = 1024; break; - case 1: ehci->periodic_size = 512; break; - case 2: ehci->periodic_size = 256; break; - default: BUG(); - } } if (HCC_LPM(hcc_params)) { /* support link power management EHCI 1.1 addendum */ -- cgit v1.2.1 From cc604ddd118cf4a699c12bc41a5fa2d2f225f702 Mon Sep 17 00:00:00 2001 From: Peter Tyser Date: Mon, 10 Jan 2011 17:34:14 -0600 Subject: USB: ehci-fsl: Fix 'have_sysif_regs' detection Previously a check was done on an ID register at the base of a CPU's internal USB registers to determine if system interface regsiters were present. The check looked for an ID register that had the format ID[0:5] == ~ID[8:13] as described in the MPC5121 User's Manual to determine if a MPC5121 or MPC83xx/85xx was being used. There are two issues with this method: - The ID register is not defined on the MPC83xx/85xx CPUs, so its unclear what is being checked on them. - Newer CPUs such as the P4080 also don't document the ID register, but do share the same format as the MPC5121. Thus the previous code did not set 'have_sysif_regs' properly which results in the P4080 not properly initializing its USB ports. Using the device tree 'compatible' node is a cleaner way to determine if 'have_sysif_regs' should be set and resolves the USB initialization issue seen on the P4080. Tested on a P4080-based system and compile tested on mpc512x_defconfig with Freescale EHCI driver enabled. Cc: Anatolij Gustschin Cc: David Brownell Cc: Kumar Gala Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Peter Tyser Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-fsl.c | 13 ------------- drivers/usb/host/ehci-fsl.h | 3 --- drivers/usb/host/fsl-mph-dr-of.c | 11 ++++++++--- 3 files changed, 8 insertions(+), 19 deletions(-) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c index 86e42892016d..5c761df7fa83 100644 --- a/drivers/usb/host/ehci-fsl.c +++ b/drivers/usb/host/ehci-fsl.c @@ -52,7 +52,6 @@ static int usb_hcd_fsl_probe(const struct hc_driver *driver, struct resource *res; int irq; int retval; - unsigned int temp; pr_debug("initializing FSL-SOC USB Controller\n"); @@ -126,18 +125,6 @@ static int usb_hcd_fsl_probe(const struct hc_driver *driver, goto err3; } - /* - * Check if it is MPC5121 SoC, otherwise set pdata->have_sysif_regs - * flag for 83xx or 8536 system interface registers. - */ - if (pdata->big_endian_mmio) - temp = in_be32(hcd->regs + FSL_SOC_USB_ID); - else - temp = in_le32(hcd->regs + FSL_SOC_USB_ID); - - if ((temp & ID_MSK) != (~((temp & NID_MSK) >> 8) & ID_MSK)) - pdata->have_sysif_regs = 1; - /* Enable USB controller, 83xx or 8536 */ if (pdata->have_sysif_regs) setbits32(hcd->regs + FSL_SOC_USB_CTRL, 0x4); diff --git a/drivers/usb/host/ehci-fsl.h b/drivers/usb/host/ehci-fsl.h index 2c8353795226..3fabed33d940 100644 --- a/drivers/usb/host/ehci-fsl.h +++ b/drivers/usb/host/ehci-fsl.h @@ -19,9 +19,6 @@ #define _EHCI_FSL_H /* offsets for the non-ehci registers in the FSL SOC USB controller */ -#define FSL_SOC_USB_ID 0x0 -#define ID_MSK 0x3f -#define NID_MSK 0x3f00 #define FSL_SOC_USB_ULPIVP 0x170 #define FSL_SOC_USB_PORTSC1 0x184 #define PORT_PTS_MSK (3<<30) diff --git a/drivers/usb/host/fsl-mph-dr-of.c b/drivers/usb/host/fsl-mph-dr-of.c index 574b99ea0700..79a66d622f9c 100644 --- a/drivers/usb/host/fsl-mph-dr-of.c +++ b/drivers/usb/host/fsl-mph-dr-of.c @@ -262,19 +262,24 @@ static void fsl_usb2_mpc5121_exit(struct platform_device *pdev) } } -struct fsl_usb2_platform_data fsl_usb2_mpc5121_pd = { +static struct fsl_usb2_platform_data fsl_usb2_mpc5121_pd = { .big_endian_desc = 1, .big_endian_mmio = 1, .es = 1, + .have_sysif_regs = 0, .le_setup_buf = 1, .init = fsl_usb2_mpc5121_init, .exit = fsl_usb2_mpc5121_exit, }; #endif /* CONFIG_PPC_MPC512x */ +static struct fsl_usb2_platform_data fsl_usb2_mpc8xxx_pd = { + .have_sysif_regs = 1, +}; + static const struct of_device_id fsl_usb2_mph_dr_of_match[] = { - { .compatible = "fsl-usb2-mph", }, - { .compatible = "fsl-usb2-dr", }, + { .compatible = "fsl-usb2-mph", .data = &fsl_usb2_mpc8xxx_pd, }, + { .compatible = "fsl-usb2-dr", .data = &fsl_usb2_mpc8xxx_pd, }, #ifdef CONFIG_PPC_MPC512x { .compatible = "fsl,mpc5121-usb2-dr", .data = &fsl_usb2_mpc5121_pd, }, #endif -- cgit v1.2.1 From 3bb8029a2445e289efade6133b01545143336f70 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Eric=20B=C3=A9nard?= Date: Thu, 13 Jan 2011 14:53:17 +0100 Subject: USB: unbreak ehci-mxc on otg port of i.MX27 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit 711669e5b80b6f2d88f61ed8a9681f83d8cbd201 fixed port 0 support for i.MX51 but broke it for (at least) i.MX27 which doesn't have a usb_phy1 clock but has a pdev->id 0. Signed-off-by: Eric Bénard Cc: Arnaud Patard Cc: Sascha Hauer Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-mxc.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/ehci-mxc.c b/drivers/usb/host/ehci-mxc.c index fa59b26fc5bc..d443fbd8535b 100644 --- a/drivers/usb/host/ehci-mxc.c +++ b/drivers/usb/host/ehci-mxc.c @@ -177,8 +177,8 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev) clk_enable(priv->ahbclk); } - /* "dr" device has its own clock */ - if (pdev->id == 0) { + /* "dr" device has its own clock on i.MX51 */ + if (cpu_is_mx51() && (pdev->id == 0)) { priv->phy1clk = clk_get(dev, "usb_phy1"); if (IS_ERR(priv->phy1clk)) { ret = PTR_ERR(priv->phy1clk); -- cgit v1.2.1 From a464dc4d4044c936d4558725fa2229fb4a1aa932 Mon Sep 17 00:00:00 2001 From: "Arnaud Patard (Rtp)" Date: Tue, 18 Jan 2011 00:04:12 +0100 Subject: USB: ehci-mxc: add work-around for efika mx/sb bug Add support for setting CHRGVBUS to workaround a hardware bug on efika mx/sb boards. See http://lists.infradead.org/pipermail/linux-arm-kernel/2011-January/037341.html Signed-off-by: Arnaud Patard Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-mxc.c | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/ehci-mxc.c b/drivers/usb/host/ehci-mxc.c index d443fbd8535b..c8e360d7d975 100644 --- a/drivers/usb/host/ehci-mxc.c +++ b/drivers/usb/host/ehci-mxc.c @@ -21,10 +21,13 @@ #include #include #include +#include #include #include +#include + #define ULPI_VIEWPORT_OFFSET 0x170 struct ehci_mxc_priv { @@ -114,6 +117,7 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev) struct usb_hcd *hcd; struct resource *res; int irq, ret; + unsigned int flags; struct ehci_mxc_priv *priv; struct device *dev = &pdev->dev; struct ehci_hcd *ehci; @@ -240,6 +244,23 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev) if (ret) goto err_add; + if (pdata->otg) { + /* + * efikamx and efikasb have some hardware bug which is + * preventing usb to work unless CHRGVBUS is set. + * It's in violation of USB specs + */ + if (machine_is_mx51_efikamx() || machine_is_mx51_efikasb()) { + flags = otg_io_read(pdata->otg, ULPI_OTG_CTRL); + flags |= ULPI_OTG_CTRL_CHRGVBUS; + ret = otg_io_write(pdata->otg, flags, ULPI_OTG_CTRL); + if (ret) { + dev_err(dev, "unable to set CHRVBUS\n"); + goto err_add; + } + } + } + return 0; err_add: -- cgit v1.2.1 From 3e434a86cb21fba95d86b8d756997c235eade037 Mon Sep 17 00:00:00 2001 From: Jarkko Nikula Date: Fri, 7 Jan 2011 11:19:52 +0200 Subject: usb: ehci-omap: Show fatal probing time errors to end user There are a few error paths in ehci_hcd_omap_probe that can be triggered because of memory allocation or hw failure. Change those dev_dbg error prints to dev_err with an error code printed so that the end users are able to notice the issue. Signed-off-by: Jarkko Nikula Signed-off-by: Felipe Balbi --- drivers/usb/host/ehci-omap.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c index 680f2ef4e59f..f784ceb862a3 100644 --- a/drivers/usb/host/ehci-omap.c +++ b/drivers/usb/host/ehci-omap.c @@ -796,7 +796,7 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev) hcd = usb_create_hcd(&ehci_omap_hc_driver, &pdev->dev, dev_name(&pdev->dev)); if (!hcd) { - dev_dbg(&pdev->dev, "failed to create hcd with err %d\n", ret); + dev_err(&pdev->dev, "failed to create hcd with err %d\n", ret); ret = -ENOMEM; goto err_create_hcd; } @@ -864,7 +864,7 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev) ret = omap_start_ehc(omap, hcd); if (ret) { - dev_dbg(&pdev->dev, "failed to start ehci\n"); + dev_err(&pdev->dev, "failed to start ehci with err %d\n", ret); goto err_start; } @@ -879,7 +879,7 @@ static int ehci_hcd_omap_probe(struct platform_device *pdev) ret = usb_add_hcd(hcd, irq, IRQF_DISABLED | IRQF_SHARED); if (ret) { - dev_dbg(&pdev->dev, "failed to add hcd with err %d\n", ret); + dev_err(&pdev->dev, "failed to add hcd with err %d\n", ret); goto err_add_hcd; } -- cgit v1.2.1 From 2bd15f1f49629f110bbbbc5a2a226bec892de87c Mon Sep 17 00:00:00 2001 From: Jesper Juhl Date: Sun, 23 Jan 2011 23:08:31 +0100 Subject: USB SL811HS HCD: Fix memory leak in sl811h_urb_enqueue() In drivers/usb/host/sl811-hcd.c::sl811h_urb_enqueue(), memory is allocated with kzalloc() and assigned to 'ep'. If we leave via the 'fail' label due to 'if (ep->maxpacket > H_MAXPACKET)', then 'ep' will go out of scope without having been assigned to anything, so we'll leak the memory we allocated. This patch fixes the leak by simply calling kfree(ep); before jumping to the 'fail' label. Signed-off-by: Jesper Juhl Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/sl811-hcd.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/sl811-hcd.c b/drivers/usb/host/sl811-hcd.c index 990f06b89eaa..2e9602a10e9b 100644 --- a/drivers/usb/host/sl811-hcd.c +++ b/drivers/usb/host/sl811-hcd.c @@ -861,6 +861,7 @@ static int sl811h_urb_enqueue( DBG("dev %d ep%d maxpacket %d\n", udev->devnum, epnum, ep->maxpacket); retval = -EINVAL; + kfree(ep); goto fail; } -- cgit v1.2.1 From 148fc55fd0449683a1d15bf219ad8d8b6fa17545 Mon Sep 17 00:00:00 2001 From: Yin Kangkai Date: Fri, 28 Jan 2011 12:04:35 +0800 Subject: USB: EHCI: fix scheduling while atomic during suspend There is a msleep with spin lock held during ehci pci suspend, which will cause kernel BUG: scheduling while atomic. Fix that. [ 184.139620] BUG: scheduling while atomic: kworker/u:11/416/0x00000002 [ 184.139632] 4 locks held by kworker/u:11/416: [ 184.139640] #0: (events_unbound){+.+.+.}, at: [] process_one_work+0x1b3/0x4cb [ 184.139669] #1: ((&entry->work)){+.+.+.}, at: [] process_one_work+0x1b3/0x4cb [ 184.139686] #2: (&__lockdep_no_validate__){+.+.+.}, at: [] __device_suspend+0x2c/0x154 [ 184.139706] #3: (&(&ehci->lock)->rlock){-.-...}, at: [] ehci_pci_suspend+0x35/0x7b [ 184.139725] Modules linked in: serio_raw pegasus joydev mrst_gfx(C) battery [ 184.139748] irq event stamp: 52 [ 184.139753] hardirqs last enabled at (51): [] mutex_lock_nested+0x258/0x293 [ 184.139766] hardirqs last disabled at (52): [] _raw_spin_lock_irqsave+0xf/0x3e [ 184.139777] softirqs last enabled at (0): [] copy_process+0x3d2/0x109d [ 184.139789] softirqs last disabled at (0): [< (null)>] (null) [ 184.139802] Pid: 416, comm: kworker/u:11 Tainted: G C 2.6.37-6.3-adaptation-oaktrail #37 [ 184.139809] Call Trace: [ 184.139820] [] __schedule_bug+0x5e/0x65 [ 184.139829] [] schedule+0xac/0xc4c [ 184.139840] [] ? string+0x37/0x8b [ 184.139853] [] ? lock_timer_base+0x1f/0x3e [ 184.139863] [] ? _raw_spin_lock_irqsave+0x35/0x3e [ 184.139876] [] ? trace_hardirqs_off+0xb/0xd [ 184.139885] [] schedule_timeout+0x283/0x2d9 [ 184.139896] [] ? process_timeout+0x0/0xa [ 184.139906] [] schedule_timeout_uninterruptible+0x15/0x17 [ 184.139916] [] msleep+0x10/0x16 [ 184.139926] [] ehci_adjust_port_wakeup_flags+0x69/0xf6 [ 184.139937] [] ehci_pci_suspend+0x48/0x7b [ 184.139946] [] suspend_common+0x52/0xbb [ 184.139956] [] hcd_pci_suspend+0x26/0x28 [ 184.139967] [] pci_pm_suspend+0x5f/0xd0 [ 184.139976] [] pm_op+0x5d/0xf0 [ 184.139986] [] __device_suspend+0xf5/0x154 [ 184.139996] [] async_suspend+0x16/0x3a [ 184.140006] [] async_run_entry_fn+0x89/0x111 [ 184.140016] [] process_one_work+0x295/0x4cb [ 184.140026] [] ? async_run_entry_fn+0x0/0x111 [ 184.140036] [] worker_thread+0x17f/0x298 [ 184.140045] [] ? worker_thread+0x0/0x298 [ 184.140055] [] kthread+0x64/0x69 [ 184.140064] [] ? kthread+0x0/0x69 [ 184.140075] [] kernel_thread_helper+0x6/0x1a Signed-off-by: Yin Kangkai Acked-by: Alan Stern CC: David Brownell CC: stable@kernel.org Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-au1xxx.c | 2 +- drivers/usb/host/ehci-hub.c | 7 +++++++ drivers/usb/host/ehci-pci.c | 2 +- 3 files changed, 9 insertions(+), 2 deletions(-) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/ehci-au1xxx.c b/drivers/usb/host/ehci-au1xxx.c index 2baf8a849086..a869e3c103d3 100644 --- a/drivers/usb/host/ehci-au1xxx.c +++ b/drivers/usb/host/ehci-au1xxx.c @@ -227,8 +227,8 @@ static int ehci_hcd_au1xxx_drv_suspend(struct device *dev) * mark HW unaccessible. The PM and USB cores make sure that * the root hub is either suspended or stopped. */ - spin_lock_irqsave(&ehci->lock, flags); ehci_prepare_ports_for_controller_suspend(ehci, device_may_wakeup(dev)); + spin_lock_irqsave(&ehci->lock, flags); ehci_writel(ehci, 0, &ehci->regs->intr_enable); (void)ehci_readl(ehci, &ehci->regs->intr_enable); diff --git a/drivers/usb/host/ehci-hub.c b/drivers/usb/host/ehci-hub.c index 796ea0c8900f..8a515f0d5988 100644 --- a/drivers/usb/host/ehci-hub.c +++ b/drivers/usb/host/ehci-hub.c @@ -111,6 +111,7 @@ static void ehci_adjust_port_wakeup_flags(struct ehci_hcd *ehci, { int port; u32 temp; + unsigned long flags; /* If remote wakeup is enabled for the root hub but disabled * for the controller, we must adjust all the port wakeup flags @@ -120,6 +121,8 @@ static void ehci_adjust_port_wakeup_flags(struct ehci_hcd *ehci, if (!ehci_to_hcd(ehci)->self.root_hub->do_remote_wakeup || do_wakeup) return; + spin_lock_irqsave(&ehci->lock, flags); + /* clear phy low-power mode before changing wakeup flags */ if (ehci->has_hostpc) { port = HCS_N_PORTS(ehci->hcs_params); @@ -131,7 +134,9 @@ static void ehci_adjust_port_wakeup_flags(struct ehci_hcd *ehci, temp = ehci_readl(ehci, hostpc_reg); ehci_writel(ehci, temp & ~HOSTPC_PHCD, hostpc_reg); } + spin_unlock_irqrestore(&ehci->lock, flags); msleep(5); + spin_lock_irqsave(&ehci->lock, flags); } port = HCS_N_PORTS(ehci->hcs_params); @@ -170,6 +175,8 @@ static void ehci_adjust_port_wakeup_flags(struct ehci_hcd *ehci, /* Does the root hub have a port wakeup pending? */ if (!suspending && (ehci_readl(ehci, &ehci->regs->status) & STS_PCD)) usb_hcd_resume_root_hub(ehci_to_hcd(ehci)); + + spin_unlock_irqrestore(&ehci->lock, flags); } static int ehci_bus_suspend (struct usb_hcd *hcd) diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c index bed07d4aab06..07bb982e59f6 100644 --- a/drivers/usb/host/ehci-pci.c +++ b/drivers/usb/host/ehci-pci.c @@ -367,8 +367,8 @@ static int ehci_pci_suspend(struct usb_hcd *hcd, bool do_wakeup) * mark HW unaccessible. The PM and USB cores make sure that * the root hub is either suspended or stopped. */ - spin_lock_irqsave (&ehci->lock, flags); ehci_prepare_ports_for_controller_suspend(ehci, do_wakeup); + spin_lock_irqsave (&ehci->lock, flags); ehci_writel(ehci, 0, &ehci->regs->intr_enable); (void)ehci_readl(ehci, &ehci->regs->intr_enable); -- cgit v1.2.1 From 8cf28f1f4de58c70e6af657bb46ca8f304c073d4 Mon Sep 17 00:00:00 2001 From: Pavankumar Kondeti Date: Fri, 4 Feb 2011 10:08:18 +0530 Subject: USB: Fix trout build failure with ci13xxx_msm gadget This patch fixes the below compilation errors. CC drivers/usb/gadget/ci13xxx_msm.o CC net/mac80211/led.o drivers/usb/gadget/ci13xxx_msm.c: In function 'ci13xxx_msm_notify_event': drivers/usb/gadget/ci13xxx_msm.c:42: error: 'USB_AHBBURST' undeclared (first use in this function) drivers/usb/gadget/ci13xxx_msm.c:42: error: (Each undeclared identifier is reported only once drivers/usb/gadget/ci13xxx_msm.c:42: error: for each function it appears in.) drivers/usb/gadget/ci13xxx_msm.c:43: error: 'USB_AHBMODE' undeclared (first use in this function) make[4]: *** [drivers/usb/gadget/ci13xxx_msm.o] Error 1 make[3]: *** [drivers/usb/gadget] Error 2 MSM USB driver is not supported on boards like trout (MSM7201) which has an external PHY. Signed-off-by: Pavankumar Kondeti Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/Kconfig | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers/usb/host') diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig index 24046c0f5878..0e6afa260ed8 100644 --- a/drivers/usb/host/Kconfig +++ b/drivers/usb/host/Kconfig @@ -151,6 +151,8 @@ config USB_EHCI_MSM Qualcomm chipsets. Root Hub has inbuilt TT. This driver depends on OTG driver for PHY initialization, clock management, powering up VBUS, and power management. + This driver is not supported on boards like trout which + has an external PHY. config USB_EHCI_HCD_PPC_OF bool "EHCI support for PPC USB controller on OF platform bus" -- cgit v1.2.1