From 978aded4b39de7f441bb9bfb18cf830de6a968d3 Mon Sep 17 00:00:00 2001 From: Giuseppe CAVALLARO Date: Mon, 25 Aug 2014 14:56:18 +0200 Subject: stmmac: fix rx checksum programming This patch is to fix the IPC bit into the GMAC control register that must be done after the core initialization otherwise it will not have any effect. Signed-off-by: Giuseppe Cavallaro Signed-off-by: David S. Miller --- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 13 ++++++------- 1 file changed, 6 insertions(+), 7 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index 08addd653728..51a89d4bb125 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -1637,6 +1637,12 @@ static int stmmac_hw_setup(struct net_device *dev) /* Initialize the MAC Core */ priv->hw->mac->core_init(priv->hw, dev->mtu); + ret = priv->hw->mac->rx_ipc(priv->hw); + if (!ret) { + pr_warn(" RX IPC Checksum Offload disabled\n"); + priv->plat->rx_coe = STMMAC_RX_COE_NONE; + } + /* Enable the MAC Rx/Tx */ stmmac_set_mac(priv->ioaddr, true); @@ -2592,7 +2598,6 @@ static const struct net_device_ops stmmac_netdev_ops = { */ static int stmmac_hw_init(struct stmmac_priv *priv) { - int ret; struct mac_device_info *mac; /* Identify the MAC HW device */ @@ -2649,12 +2654,6 @@ static int stmmac_hw_init(struct stmmac_priv *priv) /* To use alternate (extended) or normal descriptor structures */ stmmac_selec_desc_mode(priv); - ret = priv->hw->mac->rx_ipc(priv->hw); - if (!ret) { - pr_warn(" RX IPC Checksum Offload not configured.\n"); - priv->plat->rx_coe = STMMAC_RX_COE_NONE; - } - if (priv->plat->rx_coe) pr_info(" RX Checksum Offload Engine supported (type %d)\n", priv->plat->rx_coe); -- cgit v1.2.1 From f95f4045c734f801031782c8c6f8a5f381b0f69c Mon Sep 17 00:00:00 2001 From: Giuseppe CAVALLARO Date: Mon, 25 Aug 2014 14:56:19 +0200 Subject: stmmac: set ptp_clock to NULL while unregister This is to properly put to NULL the ptp_clock while un-register the PTP support. Signed-off-by: Giuseppe Cavallaro Signed-off-by: David S. Miller --- drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c index b7ad3565566c..c5ee79d8a8c5 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.c @@ -206,6 +206,7 @@ void stmmac_ptp_unregister(struct stmmac_priv *priv) { if (priv->ptp_clock) { ptp_clock_unregister(priv->ptp_clock); + priv->ptp_clock = NULL; pr_debug("Removed PTP HW clock successfully on %s\n", priv->dev->name); } -- cgit v1.2.1 From b853f31940c84cce6a3f5cb4f529b029906ee69c Mon Sep 17 00:00:00 2001 From: Jonas Jensen Date: Mon, 25 Aug 2014 16:22:11 +0200 Subject: net: moxa: clear DESC1 on ndo_start_xmit() TX buffer length is not cleared on ndo_start_xmit(). Failing to do so can bug/hang the controller and cause TX interrupts to stop altogether. Remove the readl() and compute a new value for DESC1. Addresses https://bugzilla.kernel.org/show_bug.cgi?id=69031 Signed-off-by: Jonas Jensen Signed-off-by: David S. Miller --- drivers/net/ethernet/moxa/moxart_ether.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/moxa/moxart_ether.c b/drivers/net/ethernet/moxa/moxart_ether.c index 5020fd47825d..eed70d9f0d9d 100644 --- a/drivers/net/ethernet/moxa/moxart_ether.c +++ b/drivers/net/ethernet/moxa/moxart_ether.c @@ -346,10 +346,9 @@ static int moxart_mac_start_xmit(struct sk_buff *skb, struct net_device *ndev) len = ETH_ZLEN; } - txdes1 = readl(desc + TX_REG_OFFSET_DESC1); - txdes1 |= TX_DESC1_LTS | TX_DESC1_FTS; - txdes1 &= ~(TX_DESC1_FIFO_COMPLETE | TX_DESC1_INTR_COMPLETE); - txdes1 |= (len & TX_DESC1_BUF_SIZE_MASK); + txdes1 = TX_DESC1_LTS | TX_DESC1_FTS | (len & TX_DESC1_BUF_SIZE_MASK); + if (tx_head == TX_DESC_NUM_MASK) + txdes1 |= TX_DESC1_END; writel(txdes1, desc + TX_REG_OFFSET_DESC1); writel(TX_DESC0_DMA_OWN, desc + TX_REG_OFFSET_DESC0); -- cgit v1.2.1 From 9fe1b3bc8d9182e950a744e4a47187420efa67f3 Mon Sep 17 00:00:00 2001 From: Jonas Jensen Date: Mon, 25 Aug 2014 16:22:22 +0200 Subject: net: moxa: replace build_skb() with netdev_alloc_skb_ip_align() / memcpy() build_skb() is used to make skbs out of existing RX ring memory which is bad because the RX ring is allocated only once, on probe. Memory corruption occur because said memory is reclaimed, i.e. __kfree_skb() (and eventually put_page()). Replace build_skb() with netdev_alloc_skb_ip_align() and use memcpy(). Remove SKB_DATA_ALIGN() from RX buffer size while we're at it. Addresses https://bugzilla.kernel.org/show_bug.cgi?id=69041 Signed-off-by: Jonas Jensen Signed-off-by: David S. Miller --- drivers/net/ethernet/moxa/moxart_ether.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/moxa/moxart_ether.c b/drivers/net/ethernet/moxa/moxart_ether.c index eed70d9f0d9d..d66058d5c429 100644 --- a/drivers/net/ethernet/moxa/moxart_ether.c +++ b/drivers/net/ethernet/moxa/moxart_ether.c @@ -226,13 +226,15 @@ static int moxart_rx_poll(struct napi_struct *napi, int budget) if (len > RX_BUF_SIZE) len = RX_BUF_SIZE; - skb = build_skb(priv->rx_buf[rx_head], priv->rx_buf_size); + skb = netdev_alloc_skb_ip_align(ndev, len); + if (unlikely(!skb)) { - net_dbg_ratelimited("build_skb failed\n"); + net_dbg_ratelimited("netdev_alloc_skb_ip_align failed\n"); priv->stats.rx_dropped++; priv->stats.rx_errors++; } + memcpy(skb->data, priv->rx_buf[rx_head], len); skb_put(skb, len); skb->protocol = eth_type_trans(skb, ndev); napi_gro_receive(&priv->napi, skb); @@ -464,8 +466,7 @@ static int moxart_mac_probe(struct platform_device *pdev) spin_lock_init(&priv->txlock); priv->tx_buf_size = TX_BUF_SIZE; - priv->rx_buf_size = RX_BUF_SIZE + - SKB_DATA_ALIGN(sizeof(struct skb_shared_info)); + priv->rx_buf_size = RX_BUF_SIZE; priv->tx_desc_base = dma_alloc_coherent(NULL, TX_REG_DESC_SIZE * TX_DESC_NUM, &priv->tx_base, -- cgit v1.2.1 From 777fbc31447f111a1492c90fae2bc616f836d407 Mon Sep 17 00:00:00 2001 From: Jonas Jensen Date: Mon, 25 Aug 2014 16:22:32 +0200 Subject: net: moxa: synchronize DMA memory DMA memory should be synchronized before data is passed to/from controller. Add dma_sync_single_for_cpu(.., DMA_FROM_DEVICE) to RX path and dma_sync_single_for_device(.., DMA_TO_DEVICE) to TX path. Signed-off-by: Jonas Jensen Signed-off-by: David S. Miller --- drivers/net/ethernet/moxa/moxart_ether.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/moxa/moxart_ether.c b/drivers/net/ethernet/moxa/moxart_ether.c index d66058d5c429..983d01949795 100644 --- a/drivers/net/ethernet/moxa/moxart_ether.c +++ b/drivers/net/ethernet/moxa/moxart_ether.c @@ -226,6 +226,9 @@ static int moxart_rx_poll(struct napi_struct *napi, int budget) if (len > RX_BUF_SIZE) len = RX_BUF_SIZE; + dma_sync_single_for_cpu(&ndev->dev, + priv->rx_mapping[rx_head], + priv->rx_buf_size, DMA_FROM_DEVICE); skb = netdev_alloc_skb_ip_align(ndev, len); if (unlikely(!skb)) { @@ -348,6 +351,9 @@ static int moxart_mac_start_xmit(struct sk_buff *skb, struct net_device *ndev) len = ETH_ZLEN; } + dma_sync_single_for_device(&ndev->dev, priv->tx_mapping[tx_head], + priv->tx_buf_size, DMA_TO_DEVICE); + txdes1 = TX_DESC1_LTS | TX_DESC1_FTS | (len & TX_DESC1_BUF_SIZE_MASK); if (tx_head == TX_DESC_NUM_MASK) txdes1 |= TX_DESC1_END; -- cgit v1.2.1 From 2b7890e757bc42f963c835521c2657bd16d7b7d6 Mon Sep 17 00:00:00 2001 From: Jonas Jensen Date: Mon, 25 Aug 2014 16:22:40 +0200 Subject: net: moxa: continue loop on skb allocation failure If netdev_alloc_skb_ip_align() fails, subsequent code will try to dereference an invalid pointer. Continue to next descriptor on error. While we're at it, 1. eliminate the chance of an endless loop, replace the main loop with while(rx < budget) 2. use napi_complete() and remove the explicit napi_gro_flush() Signed-off-by: Jonas Jensen Signed-off-by: David S. Miller --- drivers/net/ethernet/moxa/moxart_ether.c | 12 +++++------- 1 file changed, 5 insertions(+), 7 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/moxa/moxart_ether.c b/drivers/net/ethernet/moxa/moxart_ether.c index 983d01949795..2f12c88c66ab 100644 --- a/drivers/net/ethernet/moxa/moxart_ether.c +++ b/drivers/net/ethernet/moxa/moxart_ether.c @@ -206,7 +206,7 @@ static int moxart_rx_poll(struct napi_struct *napi, int budget) int rx_head = priv->rx_head; int rx = 0; - while (1) { + while (rx < budget) { desc = priv->rx_desc_base + (RX_REG_DESC_SIZE * rx_head); desc0 = readl(desc + RX_REG_OFFSET_DESC0); @@ -218,7 +218,7 @@ static int moxart_rx_poll(struct napi_struct *napi, int budget) net_dbg_ratelimited("packet error\n"); priv->stats.rx_dropped++; priv->stats.rx_errors++; - continue; + goto rx_next; } len = desc0 & RX_DESC0_FRAME_LEN_MASK; @@ -235,6 +235,7 @@ static int moxart_rx_poll(struct napi_struct *napi, int budget) net_dbg_ratelimited("netdev_alloc_skb_ip_align failed\n"); priv->stats.rx_dropped++; priv->stats.rx_errors++; + goto rx_next; } memcpy(skb->data, priv->rx_buf[rx_head], len); @@ -249,18 +250,15 @@ static int moxart_rx_poll(struct napi_struct *napi, int budget) if (desc0 & RX_DESC0_MULTICAST) priv->stats.multicast++; +rx_next: writel(RX_DESC0_DMA_OWN, desc + RX_REG_OFFSET_DESC0); rx_head = RX_NEXT(rx_head); priv->rx_head = rx_head; - - if (rx >= budget) - break; } if (rx < budget) { - napi_gro_flush(napi, false); - __napi_complete(napi); + napi_complete(napi); } priv->reg_imr |= RPKT_FINISH_M; -- cgit v1.2.1 From 47ccd1edc57ddabb81f6ba07e1e30201a8f578d6 Mon Sep 17 00:00:00 2001 From: Vlad Yasevich Date: Mon, 25 Aug 2014 10:34:48 -0400 Subject: e1000e: Fix TSO with non-accelerated vlans This device claims TSO support for vlans. It also allows a user to control vlan acceleration offloading. As such, it is possible to turn off vlan acceleration and configure a vlan which will continue to support TSO. In such situation the packet passed down the the device will contain a vlan header and skb->protocol will be set to ETH_P_8021Q. The device assumes that skb->protocol contains network protocol value and uses that value to set up TSO information. This results in corrupted frames sent on the wire. Corruptions include incorrect IP total length and invalid IP checksum. This patch extract the protocol value correctly and corrects TSO for non-accelerated traffic. CC: Jeff Kirsher CC: Jesse Brandeburg CC: Bruce Allan CC: Carolyn Wyborny CC: Don Skidmore CC: Greg Rose CC: Alex Duyck CC: John Ronciak CC: Mitch Williams CC: Linux NICS CC: e1000-devel@lists.sourceforge.net Signed-off-by: Vladislav Yasevich Signed-off-by: David S. Miller --- drivers/net/ethernet/intel/e1000e/netdev.c | 21 +++++++++------------ 1 file changed, 9 insertions(+), 12 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c index 65c3aef2bd36..247335d2c7ec 100644 --- a/drivers/net/ethernet/intel/e1000e/netdev.c +++ b/drivers/net/ethernet/intel/e1000e/netdev.c @@ -5164,7 +5164,8 @@ link_up: #define E1000_TX_FLAGS_VLAN_MASK 0xffff0000 #define E1000_TX_FLAGS_VLAN_SHIFT 16 -static int e1000_tso(struct e1000_ring *tx_ring, struct sk_buff *skb) +static int e1000_tso(struct e1000_ring *tx_ring, struct sk_buff *skb, + __be16 protocol) { struct e1000_context_desc *context_desc; struct e1000_buffer *buffer_info; @@ -5183,7 +5184,7 @@ static int e1000_tso(struct e1000_ring *tx_ring, struct sk_buff *skb) hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb); mss = skb_shinfo(skb)->gso_size; - if (skb->protocol == htons(ETH_P_IP)) { + if (protocol == htons(ETH_P_IP)) { struct iphdr *iph = ip_hdr(skb); iph->tot_len = 0; iph->check = 0; @@ -5231,7 +5232,8 @@ static int e1000_tso(struct e1000_ring *tx_ring, struct sk_buff *skb) return 1; } -static bool e1000_tx_csum(struct e1000_ring *tx_ring, struct sk_buff *skb) +static bool e1000_tx_csum(struct e1000_ring *tx_ring, struct sk_buff *skb, + __be16 protocol) { struct e1000_adapter *adapter = tx_ring->adapter; struct e1000_context_desc *context_desc; @@ -5239,16 +5241,10 @@ static bool e1000_tx_csum(struct e1000_ring *tx_ring, struct sk_buff *skb) unsigned int i; u8 css; u32 cmd_len = E1000_TXD_CMD_DEXT; - __be16 protocol; if (skb->ip_summed != CHECKSUM_PARTIAL) return false; - if (skb->protocol == cpu_to_be16(ETH_P_8021Q)) - protocol = vlan_eth_hdr(skb)->h_vlan_encapsulated_proto; - else - protocol = skb->protocol; - switch (protocol) { case cpu_to_be16(ETH_P_IP): if (ip_hdr(skb)->protocol == IPPROTO_TCP) @@ -5546,6 +5542,7 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb, int count = 0; int tso; unsigned int f; + __be16 protocol = vlan_get_protocol(skb); if (test_bit(__E1000_DOWN, &adapter->state)) { dev_kfree_skb_any(skb); @@ -5620,7 +5617,7 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb, first = tx_ring->next_to_use; - tso = e1000_tso(tx_ring, skb); + tso = e1000_tso(tx_ring, skb, protocol); if (tso < 0) { dev_kfree_skb_any(skb); return NETDEV_TX_OK; @@ -5628,14 +5625,14 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb, if (tso) tx_flags |= E1000_TX_FLAGS_TSO; - else if (e1000_tx_csum(tx_ring, skb)) + else if (e1000_tx_csum(tx_ring, skb, protocol)) tx_flags |= E1000_TX_FLAGS_CSUM; /* Old method was to assume IPv4 packet by default if TSO was enabled. * 82571 hardware supports TSO capabilities for IPv6 as well... * no longer assume, we must. */ - if (skb->protocol == htons(ETH_P_IP)) + if (protocol == htons(ETH_P_IP)) tx_flags |= E1000_TX_FLAGS_IPV4; if (unlikely(skb->no_fcs)) -- cgit v1.2.1 From 06f4d0333e86e302da3ac8386f873d5e353baf2e Mon Sep 17 00:00:00 2001 From: Vlad Yasevich Date: Mon, 25 Aug 2014 10:34:49 -0400 Subject: e1000: Fix TSO for non-accelerated vlan traffic This device claims TSO and checksum support for vlans. It also allows a user to control vlan acceleration offloading. As such, it is possible to turn off vlan acceleration and configure a vlan which will continue to support TSO. In such situation the packet passed down the the device will contain a vlan header and skb->protocol will be set to ETH_P_8021Q. The device assumes that skb->protocol contains network protocol value and uses that value to set up TSO and checksum information. This will results in corrupted frames sent on the wire. This patch extract the protocol value correctly and corrects TSO for non-accelerated traffic. CC: Jeff Kirsher CC: Jesse Brandeburg CC: Bruce Allan CC: Carolyn Wyborny CC: Don Skidmore CC: Greg Rose CC: Alex Duyck CC: John Ronciak CC: Mitch Williams CC: Linux NICS CC: e1000-devel@lists.sourceforge.net Signed-off-by: Vladislav Yasevich Signed-off-by: David S. Miller --- drivers/net/ethernet/intel/e1000/e1000_main.c | 19 +++++++++++-------- 1 file changed, 11 insertions(+), 8 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/intel/e1000/e1000_main.c b/drivers/net/ethernet/intel/e1000/e1000_main.c index cbc330b301cd..ad3d5d12173f 100644 --- a/drivers/net/ethernet/intel/e1000/e1000_main.c +++ b/drivers/net/ethernet/intel/e1000/e1000_main.c @@ -2674,7 +2674,8 @@ set_itr_now: #define E1000_TX_FLAGS_VLAN_SHIFT 16 static int e1000_tso(struct e1000_adapter *adapter, - struct e1000_tx_ring *tx_ring, struct sk_buff *skb) + struct e1000_tx_ring *tx_ring, struct sk_buff *skb, + __be16 protocol) { struct e1000_context_desc *context_desc; struct e1000_buffer *buffer_info; @@ -2692,7 +2693,7 @@ static int e1000_tso(struct e1000_adapter *adapter, hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb); mss = skb_shinfo(skb)->gso_size; - if (skb->protocol == htons(ETH_P_IP)) { + if (protocol == htons(ETH_P_IP)) { struct iphdr *iph = ip_hdr(skb); iph->tot_len = 0; iph->check = 0; @@ -2702,7 +2703,7 @@ static int e1000_tso(struct e1000_adapter *adapter, 0); cmd_length = E1000_TXD_CMD_IP; ipcse = skb_transport_offset(skb) - 1; - } else if (skb->protocol == htons(ETH_P_IPV6)) { + } else if (skb_is_gso_v6(skb)) { ipv6_hdr(skb)->payload_len = 0; tcp_hdr(skb)->check = ~csum_ipv6_magic(&ipv6_hdr(skb)->saddr, @@ -2745,7 +2746,8 @@ static int e1000_tso(struct e1000_adapter *adapter, } static bool e1000_tx_csum(struct e1000_adapter *adapter, - struct e1000_tx_ring *tx_ring, struct sk_buff *skb) + struct e1000_tx_ring *tx_ring, struct sk_buff *skb, + __be16 protocol) { struct e1000_context_desc *context_desc; struct e1000_buffer *buffer_info; @@ -2756,7 +2758,7 @@ static bool e1000_tx_csum(struct e1000_adapter *adapter, if (skb->ip_summed != CHECKSUM_PARTIAL) return false; - switch (skb->protocol) { + switch (protocol) { case cpu_to_be16(ETH_P_IP): if (ip_hdr(skb)->protocol == IPPROTO_TCP) cmd_len |= E1000_TXD_CMD_TCP; @@ -3097,6 +3099,7 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb, int count = 0; int tso; unsigned int f; + __be16 protocol = vlan_get_protocol(skb); /* This goes back to the question of how to logically map a Tx queue * to a flow. Right now, performance is impacted slightly negatively @@ -3210,7 +3213,7 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb, first = tx_ring->next_to_use; - tso = e1000_tso(adapter, tx_ring, skb); + tso = e1000_tso(adapter, tx_ring, skb, protocol); if (tso < 0) { dev_kfree_skb_any(skb); return NETDEV_TX_OK; @@ -3220,10 +3223,10 @@ static netdev_tx_t e1000_xmit_frame(struct sk_buff *skb, if (likely(hw->mac_type != e1000_82544)) tx_ring->last_tx_tso = true; tx_flags |= E1000_TX_FLAGS_TSO; - } else if (likely(e1000_tx_csum(adapter, tx_ring, skb))) + } else if (likely(e1000_tx_csum(adapter, tx_ring, skb, protocol))) tx_flags |= E1000_TX_FLAGS_CSUM; - if (likely(skb->protocol == htons(ETH_P_IP))) + if (protocol == htons(ETH_P_IP)) tx_flags |= E1000_TX_FLAGS_IPV4; if (unlikely(skb->no_fcs)) -- cgit v1.2.1 From 1c53730a04fb651e35af0a12bd35f6a00481f53c Mon Sep 17 00:00:00 2001 From: Vlad Yasevich Date: Mon, 25 Aug 2014 10:34:50 -0400 Subject: bna: Support TSO and partial checksum with non-accelerated vlans. This device claims TSO and checksum support for vlans. It also allows a user to control vlan acceleration offloading. As such, it is possible to turn off vlan acceleration and configure a vlan which will continue to support TSO. In such situation the packet passed down the the device will contain a vlan header and skb->protocol will be set to ETH_P_8021Q. The device assumes that skb->protocol contains network protocol value and uses that value to set up TSO information. This results in corrupted frames sent on the wire. This patch extract the protocol value correctly and corrects TSO and checksums for non-accelerated traffic. CC: Rasesh Mody Signed-off-by: Vladislav Yasevich Signed-off-by: David S. Miller --- drivers/net/ethernet/brocade/bna/bnad.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/brocade/bna/bnad.c b/drivers/net/ethernet/brocade/bna/bnad.c index ff8cae5e2535..ffc92a41d75b 100644 --- a/drivers/net/ethernet/brocade/bna/bnad.c +++ b/drivers/net/ethernet/brocade/bna/bnad.c @@ -2506,7 +2506,7 @@ bnad_tso_prepare(struct bnad *bnad, struct sk_buff *skb) * For TSO, the TCP checksum field is seeded with pseudo-header sum * excluding the length field. */ - if (skb->protocol == htons(ETH_P_IP)) { + if (vlan_get_protocol(skb) == htons(ETH_P_IP)) { struct iphdr *iph = ip_hdr(skb); /* Do we really need these? */ @@ -2870,12 +2870,13 @@ bnad_txq_wi_prepare(struct bnad *bnad, struct bna_tcb *tcb, } if (skb->ip_summed == CHECKSUM_PARTIAL) { + __be16 net_proto = vlan_get_protocol(skb); u8 proto = 0; - if (skb->protocol == htons(ETH_P_IP)) + if (net_proto == htons(ETH_P_IP)) proto = ip_hdr(skb)->protocol; #ifdef NETIF_F_IPV6_CSUM - else if (skb->protocol == htons(ETH_P_IPV6)) { + else if (net_proto == htons(ETH_P_IPV6)) { /* nexthdr may not be TCP immediately. */ proto = ipv6_hdr(skb)->nexthdr; } -- cgit v1.2.1 From be1d1486122092f5a323539ee4cc328d06083f63 Mon Sep 17 00:00:00 2001 From: Vlad Yasevich Date: Mon, 25 Aug 2014 10:34:51 -0400 Subject: ehea: Fix TSO and hw checksums with non-accelerated vlan packets. The driver claims that it can do TSO and IP checksums on vlan devices and also allows user to control vlan acceleration offloading. This makes it possible to push traffic to this driver that has TSO or partial checksums set, but also have a non-accelearted vlan header. In this case, the driver will fail to correctly identify such traffic and will not correctly perform segmentation and checksum calculation. Fix this by using vlan_get_protocol() helper instead of assuming skb->protocol always has this information. CC: Thadeu Lima de Souza Cascardo Signed-off-by: Vladislav Yasevich Signed-off-by: David S. Miller --- drivers/net/ethernet/ibm/ehea/ehea_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/ibm/ehea/ehea_main.c b/drivers/net/ethernet/ibm/ehea/ehea_main.c index a0b418e007a0..566b17db135a 100644 --- a/drivers/net/ethernet/ibm/ehea/ehea_main.c +++ b/drivers/net/ethernet/ibm/ehea/ehea_main.c @@ -1994,7 +1994,7 @@ static void xmit_common(struct sk_buff *skb, struct ehea_swqe *swqe) { swqe->tx_control |= EHEA_SWQE_IMM_DATA_PRESENT | EHEA_SWQE_CRC; - if (skb->protocol != htons(ETH_P_IP)) + if (vlan_get_protocol(skb) != htons(ETH_P_IP)) return; if (skb->ip_summed == CHECKSUM_PARTIAL) -- cgit v1.2.1 From 3d34dd03d55c3fa6c332e43e545ec18feb79ee85 Mon Sep 17 00:00:00 2001 From: Vlad Yasevich Date: Mon, 25 Aug 2014 10:34:52 -0400 Subject: i40e: Fix TSO and hw checksums for non-accelerated vlan packets. This device claims TSO and checksum support for vlans. It also allows a user to control vlan acceleration offloading. As such, it is possible to turn off vlan acceleration and configure a vlan which will continue to support TSO and hw checksums. In such situation the packet passed down the the device will contain a vlan header and skb->protocol will be set to ETH_P_8021Q. The device assumes that skb->protocol contains network protocol value and uses that value to set up TSO and checksum information. This results in corrupted frames sent on the wire. This patch extract the protocol value correctly and corrects TSO and checksums for non-accelerated traffic. Fix this by using vlan_get_protocol() helper. CC: Jeff Kirsher CC: Jesse Brandeburg CC: Bruce Allan CC: Carolyn Wyborny CC: Don Skidmore CC: Greg Rose CC: Alex Duyck CC: John Ronciak CC: Mitch Williams CC: Linux NICS CC: e1000-devel@lists.sourceforge.net Signed-off-by: Vladislav Yasevich Signed-off-by: David S. Miller --- drivers/net/ethernet/intel/i40e/i40e_txrx.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/intel/i40e/i40e_txrx.c b/drivers/net/ethernet/intel/i40e/i40e_txrx.c index a51aa37b7b5a..369848e107f8 100644 --- a/drivers/net/ethernet/intel/i40e/i40e_txrx.c +++ b/drivers/net/ethernet/intel/i40e/i40e_txrx.c @@ -2295,7 +2295,7 @@ static netdev_tx_t i40e_xmit_frame_ring(struct sk_buff *skb, goto out_drop; /* obtain protocol of skb */ - protocol = skb->protocol; + protocol = vlan_get_protocol(skb); /* record the location of the first descriptor for this packet */ first = &tx_ring->tx_bi[tx_ring->next_to_use]; -- cgit v1.2.1 From a12c415834cc335ae015ba104e78c3fb35ec9be9 Mon Sep 17 00:00:00 2001 From: Vlad Yasevich Date: Mon, 25 Aug 2014 10:34:53 -0400 Subject: i40evf: Fix TSO and hw checksums for non-accelerated vlan packets. This device claims TSO and checksum support for vlans. It also allows a user to control vlan acceleration offloading. As such, it is possible to turn off vlan acceleration and configure a vlan which will continue to support TSO and hw checksums. In such situation the packet passed down the the device will contain a vlan header and skb->protocol will be set to ETH_P_8021Q. The device assumes that skb->protocol contains network protocol value and uses that value to set up TSO and checksum information. This results in corrupted frames sent on the wire. This patch extract the protocol value correctly and corrects TSO and checksums for non-accelerated traffic. Fix this by using vlan_get_protocol() helper. CC: Jeff Kirsher CC: Jesse Brandeburg CC: Bruce Allan CC: Carolyn Wyborny CC: Don Skidmore CC: Greg Rose CC: Alex Duyck CC: John Ronciak CC: Mitch Williams CC: Linux NICS CC: e1000-devel@lists.sourceforge.net Signed-off-by: Vladislav Yasevich Signed-off-by: David S. Miller --- drivers/net/ethernet/intel/i40evf/i40e_txrx.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c index 79bf96ca6489..95a3ec236b49 100644 --- a/drivers/net/ethernet/intel/i40evf/i40e_txrx.c +++ b/drivers/net/ethernet/intel/i40evf/i40e_txrx.c @@ -1597,7 +1597,7 @@ static netdev_tx_t i40e_xmit_frame_ring(struct sk_buff *skb, goto out_drop; /* obtain protocol of skb */ - protocol = skb->protocol; + protocol = vlan_get_protocol(skb); /* record the location of the first descriptor for this packet */ first = &tx_ring->tx_bi[tx_ring->next_to_use]; -- cgit v1.2.1 From 817dbfa5d1bc276a72c1a577310382008e8aca0a Mon Sep 17 00:00:00 2001 From: Vlad Yasevich Date: Mon, 25 Aug 2014 10:34:54 -0400 Subject: mvneta: Fix TSO and checksum for non-acceleration vlan traffic This driver doesn't appear to support vlan acceleration at all. However, it does claim to support TSO and IP checksums for vlan devices. Thus any configured vlan device would end up passing down partial checksums or TSO frames. The driver also uses the value from skb->protocol to determine TSO and checksum offload information, but assumes that skb->protocol holds the l3 protocol information. As a result, vlan traffic with partial checksums or TSO will fail those checks and TSO will not happen. Fix this by using vlan_get_protocol() helper. CC: Thomas Petazzoni Signed-off-by: Vladislav Yasevich Signed-off-by: David S. Miller --- drivers/net/ethernet/marvell/mvneta.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c index c9f1d1b7ef37..133f8c6444e0 100644 --- a/drivers/net/ethernet/marvell/mvneta.c +++ b/drivers/net/ethernet/marvell/mvneta.c @@ -1371,15 +1371,16 @@ static u32 mvneta_skb_tx_csum(struct mvneta_port *pp, struct sk_buff *skb) { if (skb->ip_summed == CHECKSUM_PARTIAL) { int ip_hdr_len = 0; + __be16 l3_proto = vlan_get_protocol(skb); u8 l4_proto; - if (skb->protocol == htons(ETH_P_IP)) { + if (l3_proto == htons(ETH_P_IP)) { struct iphdr *ip4h = ip_hdr(skb); /* Calculate IPv4 checksum and L4 checksum */ ip_hdr_len = ip4h->ihl; l4_proto = ip4h->protocol; - } else if (skb->protocol == htons(ETH_P_IPV6)) { + } else if (l3_proto == htons(ETH_P_IPV6)) { struct ipv6hdr *ip6h = ipv6_hdr(skb); /* Read l4_protocol from one of IPv6 extra headers */ @@ -1390,7 +1391,7 @@ static u32 mvneta_skb_tx_csum(struct mvneta_port *pp, struct sk_buff *skb) return MVNETA_TX_L4_CSUM_NOT; return mvneta_txq_desc_csum(skb_network_offset(skb), - skb->protocol, ip_hdr_len, l4_proto); + l3_proto, ip_hdr_len, l4_proto); } return MVNETA_TX_L4_CSUM_NOT; -- cgit v1.2.1 From 1ee1cfe7d3df00bff11dd28576eeac1875d7d51f Mon Sep 17 00:00:00 2001 From: Vlad Yasevich Date: Mon, 25 Aug 2014 10:34:55 -0400 Subject: qlge: Fix TSO for non-accelerated vlan traffic This device claims TSO support for vlans. It also allows a user to control vlan acceleration offloading. As such, it is possible to turn off vlan acceleration and configure a vlan which will continue to send TSO traffic. In such situation the packet passed down the the device will contain a vlan header and skb->protocol will be set to ETH_P_8021Q. The device assumes that skb->protocol contains network protocol value and uses that value to set up TSO information. This results in corrupted frames sent on the wire. This patch extracts the protocol value correctly by using a vlan_get_protocol() helper and corrects corrupt TSO frames. CC: Shahed Shaikh CC: Jitendra Kalsaria CC: Ron Mercer CC: linux-driver@qlogic.com Signed-off-by: Vladislav Yasevich Acked-by: Shahed Shaikh Signed-off-by: David S. Miller --- drivers/net/ethernet/qlogic/qlge/qlge_main.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/qlogic/qlge/qlge_main.c b/drivers/net/ethernet/qlogic/qlge/qlge_main.c index 188626e2a861..3e96f269150d 100644 --- a/drivers/net/ethernet/qlogic/qlge/qlge_main.c +++ b/drivers/net/ethernet/qlogic/qlge/qlge_main.c @@ -2556,6 +2556,7 @@ static int ql_tso(struct sk_buff *skb, struct ob_mac_tso_iocb_req *mac_iocb_ptr) if (skb_is_gso(skb)) { int err; + __be16 l3_proto = vlan_get_protocol(skb); err = skb_cow_head(skb, 0); if (err < 0) @@ -2572,7 +2573,7 @@ static int ql_tso(struct sk_buff *skb, struct ob_mac_tso_iocb_req *mac_iocb_ptr) << OB_MAC_TRANSPORT_HDR_SHIFT); mac_iocb_ptr->mss = cpu_to_le16(skb_shinfo(skb)->gso_size); mac_iocb_ptr->flags2 |= OB_MAC_TSO_IOCB_LSO; - if (likely(skb->protocol == htons(ETH_P_IP))) { + if (likely(l3_proto == htons(ETH_P_IP))) { struct iphdr *iph = ip_hdr(skb); iph->check = 0; mac_iocb_ptr->flags1 |= OB_MAC_TSO_IOCB_IP4; @@ -2580,7 +2581,7 @@ static int ql_tso(struct sk_buff *skb, struct ob_mac_tso_iocb_req *mac_iocb_ptr) iph->daddr, 0, IPPROTO_TCP, 0); - } else if (skb->protocol == htons(ETH_P_IPV6)) { + } else if (l3_proto == htons(ETH_P_IPV6)) { mac_iocb_ptr->flags1 |= OB_MAC_TSO_IOCB_IP6; tcp_hdr(skb)->check = ~csum_ipv6_magic(&ipv6_hdr(skb)->saddr, -- cgit v1.2.1 From 2d39d120781a5770573dc6ed672a5a562f541aea Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Mon, 25 Aug 2014 20:21:55 -0700 Subject: mvneta: Add missing if_vlan.h include. drivers/net/ethernet/marvell/mvneta.c: In function 'mvneta_skb_tx_csum': drivers/net/ethernet/marvell/mvneta.c:1374:3: error: implicit declaration of function 'vlan_get_protocol' [-Werror=implicit-function-declaration] __be16 l3_proto = vlan_get_protocol(skb); ^ Reporeted-by: Stephen Rothwell Signed-off-by: David S. Miller --- drivers/net/ethernet/marvell/mvneta.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c index 133f8c6444e0..ade067de1689 100644 --- a/drivers/net/ethernet/marvell/mvneta.c +++ b/drivers/net/ethernet/marvell/mvneta.c @@ -20,6 +20,7 @@ #include #include #include +#include #include #include #include -- cgit v1.2.1 From b1dee4793fb8fec8e6b2efb68953b465a65c6b3e Mon Sep 17 00:00:00 2001 From: Giuseppe CAVALLARO Date: Wed, 27 Aug 2014 08:20:04 +0200 Subject: stmmac: prevent false carrier sense detection This patch is to w/a a problem that happens on some boxes when run at 10Mbps Half duplex mode. During the transmission the CSR signal is asserted for some time and the frames aborted because of carrier sense error. This is reported by MMC HW counter: txcarrier signal. This actually is a false carrier so the frames are good and there is no reason to ask for dropping them. This patch so disables the Carrier Sense During Transmission and this means that the MAC transmitter ignore the CRS signal during frame transmission in Half-Duplex mode. Signed-off-by: Giuseppe Cavallaro Acked-by: Vince Bridgers Acked-by: Ley Foon Tan Acked-by: Chen-Yu Tsai Signed-off-by: David S. Miller --- drivers/net/ethernet/stmicro/stmmac/dwmac1000.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h b/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h index 71b5419256c1..64d8f56a9c17 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000.h @@ -153,7 +153,7 @@ enum inter_frame_gap { #define GMAC_CONTROL_RE 0x00000004 /* Receiver Enable */ #define GMAC_CORE_INIT (GMAC_CONTROL_JD | GMAC_CONTROL_PS | GMAC_CONTROL_ACS | \ - GMAC_CONTROL_BE) + GMAC_CONTROL_BE | GMAC_CONTROL_DCRS) /* GMAC Frame Filter defines */ #define GMAC_FRAME_FILTER_PR 0x00000001 /* Promiscuous Mode */ -- cgit v1.2.1 From 2b78d348f1bc3396ca1662c6a6177a7fb1ca62ff Mon Sep 17 00:00:00 2001 From: Giuseppe CAVALLARO Date: Wed, 27 Aug 2014 08:26:13 +0200 Subject: stmmac: fix tipo on mmc crc error This patch is to fix a typo on mmc rx crc error when reported by ethtool. Signed-off-by: Giuseppe Cavallaro Signed-off-by: David S. Miller --- drivers/net/ethernet/stmicro/stmmac/mmc.h | 2 +- drivers/net/ethernet/stmicro/stmmac/mmc_core.c | 2 +- drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c | 2 +- 3 files changed, 3 insertions(+), 3 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/stmicro/stmmac/mmc.h b/drivers/net/ethernet/stmicro/stmmac/mmc.h index 8607488cbcfc..192c2491330b 100644 --- a/drivers/net/ethernet/stmicro/stmmac/mmc.h +++ b/drivers/net/ethernet/stmicro/stmmac/mmc.h @@ -68,7 +68,7 @@ struct stmmac_counters { unsigned int mmc_rx_octetcount_g; unsigned int mmc_rx_broadcastframe_g; unsigned int mmc_rx_multicastframe_g; - unsigned int mmc_rx_crc_errror; + unsigned int mmc_rx_crc_error; unsigned int mmc_rx_align_error; unsigned int mmc_rx_run_error; unsigned int mmc_rx_jabber_error; diff --git a/drivers/net/ethernet/stmicro/stmmac/mmc_core.c b/drivers/net/ethernet/stmicro/stmmac/mmc_core.c index 50617c5a0bdb..08c483bd2ec7 100644 --- a/drivers/net/ethernet/stmicro/stmmac/mmc_core.c +++ b/drivers/net/ethernet/stmicro/stmmac/mmc_core.c @@ -196,7 +196,7 @@ void dwmac_mmc_read(void __iomem *ioaddr, struct stmmac_counters *mmc) mmc->mmc_rx_octetcount_g += readl(ioaddr + MMC_RX_OCTETCOUNT_G); mmc->mmc_rx_broadcastframe_g += readl(ioaddr + MMC_RX_BROADCASTFRAME_G); mmc->mmc_rx_multicastframe_g += readl(ioaddr + MMC_RX_MULTICASTFRAME_G); - mmc->mmc_rx_crc_errror += readl(ioaddr + MMC_RX_CRC_ERRROR); + mmc->mmc_rx_crc_error += readl(ioaddr + MMC_RX_CRC_ERRROR); mmc->mmc_rx_align_error += readl(ioaddr + MMC_RX_ALIGN_ERROR); mmc->mmc_rx_run_error += readl(ioaddr + MMC_RX_RUN_ERROR); mmc->mmc_rx_jabber_error += readl(ioaddr + MMC_RX_JABBER_ERROR); diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c index 9af50bae4dde..cf4f38db1c0a 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c @@ -175,7 +175,7 @@ static const struct stmmac_stats stmmac_mmc[] = { STMMAC_MMC_STAT(mmc_rx_octetcount_g), STMMAC_MMC_STAT(mmc_rx_broadcastframe_g), STMMAC_MMC_STAT(mmc_rx_multicastframe_g), - STMMAC_MMC_STAT(mmc_rx_crc_errror), + STMMAC_MMC_STAT(mmc_rx_crc_error), STMMAC_MMC_STAT(mmc_rx_align_error), STMMAC_MMC_STAT(mmc_rx_run_error), STMMAC_MMC_STAT(mmc_rx_jabber_error), -- cgit v1.2.1 From 5566401f2f10556776fd199c11d6a02a5e0b7b95 Mon Sep 17 00:00:00 2001 From: Giuseppe CAVALLARO Date: Wed, 27 Aug 2014 10:37:49 +0200 Subject: stmmac: ptp: fix the reference clock The PTP reference clock, used for setting the addend in the Timestamp Addend Register, was erroneously hard-coded (as reported in the databook just as example). The patch removes the macro named: STMMAC_SYSCLOCK and allows to use a reference clock (clk_ptp_ref_i) that can be passed from the platform. If not passed, the main driver clock will be used as default; note that this can be fine on some platforms. Note that, prior this patch, using the old STMMAC_SYSCLOCK on some platforms, as side effect, the ptp clock can move faster/slower than the system clock. Signed-off-by: Giuseppe Cavallaro Signed-off-by: David S. Miller --- drivers/net/ethernet/stmicro/stmmac/stmmac.h | 2 ++ drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 20 ++++++++++++++++---- drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.h | 2 -- 3 files changed, 18 insertions(+), 6 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h index ca01035634a7..128a0b723a00 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h @@ -105,6 +105,8 @@ struct stmmac_priv { struct ptp_clock *ptp_clock; struct ptp_clock_info ptp_clock_ops; unsigned int default_addend; + struct clk *clk_ptp_ref; + unsigned int clk_ptp_rate; u32 adv_ts; int use_riwt; int irq_wake; diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index 51a89d4bb125..03652891fcbf 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -603,16 +603,16 @@ static int stmmac_hwtstamp_ioctl(struct net_device *dev, struct ifreq *ifr) /* calculate default added value: * formula is : * addend = (2^32)/freq_div_ratio; - * where, freq_div_ratio = STMMAC_SYSCLOCK/50MHz - * hence, addend = ((2^32) * 50MHz)/STMMAC_SYSCLOCK; - * NOTE: STMMAC_SYSCLOCK should be >= 50MHz to + * where, freq_div_ratio = clk_ptp_ref_i/50MHz + * hence, addend = ((2^32) * 50MHz)/clk_ptp_ref_i; + * NOTE: clk_ptp_ref_i should be >= 50MHz to * achive 20ns accuracy. * * 2^x * y == (y << x), hence * 2^32 * 50000000 ==> (50000000 << 32) */ temp = (u64) (50000000ULL << 32); - priv->default_addend = div_u64(temp, STMMAC_SYSCLOCK); + priv->default_addend = div_u64(temp, priv->clk_ptp_rate); priv->hw->ptp->config_addend(priv->ioaddr, priv->default_addend); @@ -638,6 +638,16 @@ static int stmmac_init_ptp(struct stmmac_priv *priv) if (!(priv->dma_cap.time_stamp || priv->dma_cap.atime_stamp)) return -EOPNOTSUPP; + /* Fall-back to main clock in case of no PTP ref is passed */ + priv->clk_ptp_ref = devm_clk_get(priv->device, "clk_ptp_ref"); + if (IS_ERR(priv->clk_ptp_ref)) { + priv->clk_ptp_rate = clk_get_rate(priv->stmmac_clk); + priv->clk_ptp_ref = NULL; + } else { + clk_prepare_enable(priv->clk_ptp_ref); + priv->clk_ptp_rate = clk_get_rate(priv->clk_ptp_ref); + } + priv->adv_ts = 0; if (priv->dma_cap.atime_stamp && priv->extend_desc) priv->adv_ts = 1; @@ -657,6 +667,8 @@ static int stmmac_init_ptp(struct stmmac_priv *priv) static void stmmac_release_ptp(struct stmmac_priv *priv) { + if (priv->clk_ptp_ref) + clk_disable_unprepare(priv->clk_ptp_ref); stmmac_ptp_unregister(priv); } diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.h b/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.h index 3dbc047622fa..4535df37c227 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.h +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_ptp.h @@ -25,8 +25,6 @@ #ifndef __STMMAC_PTP_H__ #define __STMMAC_PTP_H__ -#define STMMAC_SYSCLOCK 62500000 - /* IEEE 1588 PTP register offsets */ #define PTP_TCR 0x0700 /* Timestamp Control Reg */ #define PTP_SSIR 0x0704 /* Sub-Second Increment Reg */ -- cgit v1.2.1 From 362b37be01edc7429e3ebaa89613517d57863f5c Mon Sep 17 00:00:00 2001 From: Giuseppe CAVALLARO Date: Wed, 27 Aug 2014 11:27:00 +0200 Subject: stmmac: fix dma api misuse Enabling DMA_API_DEBUG, warnings are reported at runtime because the device driver frees DMA memory with wrong functions and it does not call dma_mapping_error after mapping dma memory. The first problem is fixed by of introducing a flag that helps us keeping track which mapping technique was used, so that we can use the right API for unmap. This approach was inspired by the e1000 driver, which uses a similar technique. Signed-off-by: Andre Draszik Signed-off-by: Giuseppe Cavallaro Reviewed-by: Denis Kirjanov Cc: Hans de Goede Signed-off-by: David S. Miller --- drivers/net/ethernet/stmicro/stmmac/chain_mode.c | 14 +++-- drivers/net/ethernet/stmicro/stmmac/common.h | 2 +- drivers/net/ethernet/stmicro/stmmac/ring_mode.c | 15 +++-- drivers/net/ethernet/stmicro/stmmac/stmmac.h | 7 ++- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 68 +++++++++++++++++------ 5 files changed, 79 insertions(+), 27 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/stmicro/stmmac/chain_mode.c b/drivers/net/ethernet/stmicro/stmmac/chain_mode.c index c553f6b5a913..cf28daba4346 100644 --- a/drivers/net/ethernet/stmicro/stmmac/chain_mode.c +++ b/drivers/net/ethernet/stmicro/stmmac/chain_mode.c @@ -28,7 +28,7 @@ #include "stmmac.h" -static unsigned int stmmac_jumbo_frm(void *p, struct sk_buff *skb, int csum) +static int stmmac_jumbo_frm(void *p, struct sk_buff *skb, int csum) { struct stmmac_priv *priv = (struct stmmac_priv *)p; unsigned int txsize = priv->dma_tx_size; @@ -47,7 +47,9 @@ static unsigned int stmmac_jumbo_frm(void *p, struct sk_buff *skb, int csum) desc->des2 = dma_map_single(priv->device, skb->data, bmax, DMA_TO_DEVICE); - priv->tx_skbuff_dma[entry] = desc->des2; + if (dma_mapping_error(priv->device, desc->des2)) + return -1; + priv->tx_skbuff_dma[entry].buf = desc->des2; priv->hw->desc->prepare_tx_desc(desc, 1, bmax, csum, STMMAC_CHAIN_MODE); while (len != 0) { @@ -59,7 +61,9 @@ static unsigned int stmmac_jumbo_frm(void *p, struct sk_buff *skb, int csum) desc->des2 = dma_map_single(priv->device, (skb->data + bmax * i), bmax, DMA_TO_DEVICE); - priv->tx_skbuff_dma[entry] = desc->des2; + if (dma_mapping_error(priv->device, desc->des2)) + return -1; + priv->tx_skbuff_dma[entry].buf = desc->des2; priv->hw->desc->prepare_tx_desc(desc, 0, bmax, csum, STMMAC_CHAIN_MODE); priv->hw->desc->set_tx_owner(desc); @@ -69,7 +73,9 @@ static unsigned int stmmac_jumbo_frm(void *p, struct sk_buff *skb, int csum) desc->des2 = dma_map_single(priv->device, (skb->data + bmax * i), len, DMA_TO_DEVICE); - priv->tx_skbuff_dma[entry] = desc->des2; + if (dma_mapping_error(priv->device, desc->des2)) + return -1; + priv->tx_skbuff_dma[entry].buf = desc->des2; priv->hw->desc->prepare_tx_desc(desc, 0, len, csum, STMMAC_CHAIN_MODE); priv->hw->desc->set_tx_owner(desc); diff --git a/drivers/net/ethernet/stmicro/stmmac/common.h b/drivers/net/ethernet/stmicro/stmmac/common.h index de507c32036c..bd54238e2df8 100644 --- a/drivers/net/ethernet/stmicro/stmmac/common.h +++ b/drivers/net/ethernet/stmicro/stmmac/common.h @@ -425,7 +425,7 @@ struct stmmac_mode_ops { void (*init) (void *des, dma_addr_t phy_addr, unsigned int size, unsigned int extend_desc); unsigned int (*is_jumbo_frm) (int len, int ehn_desc); - unsigned int (*jumbo_frm) (void *priv, struct sk_buff *skb, int csum); + int (*jumbo_frm)(void *priv, struct sk_buff *skb, int csum); int (*set_16kib_bfsize)(int mtu); void (*init_desc3)(struct dma_desc *p); void (*refill_desc3) (void *priv, struct dma_desc *p); diff --git a/drivers/net/ethernet/stmicro/stmmac/ring_mode.c b/drivers/net/ethernet/stmicro/stmmac/ring_mode.c index 650a4be6bce5..5dd50c6cda5b 100644 --- a/drivers/net/ethernet/stmicro/stmmac/ring_mode.c +++ b/drivers/net/ethernet/stmicro/stmmac/ring_mode.c @@ -28,7 +28,7 @@ #include "stmmac.h" -static unsigned int stmmac_jumbo_frm(void *p, struct sk_buff *skb, int csum) +static int stmmac_jumbo_frm(void *p, struct sk_buff *skb, int csum) { struct stmmac_priv *priv = (struct stmmac_priv *)p; unsigned int txsize = priv->dma_tx_size; @@ -53,7 +53,10 @@ static unsigned int stmmac_jumbo_frm(void *p, struct sk_buff *skb, int csum) desc->des2 = dma_map_single(priv->device, skb->data, bmax, DMA_TO_DEVICE); - priv->tx_skbuff_dma[entry] = desc->des2; + if (dma_mapping_error(priv->device, desc->des2)) + return -1; + + priv->tx_skbuff_dma[entry].buf = desc->des2; desc->des3 = desc->des2 + BUF_SIZE_4KiB; priv->hw->desc->prepare_tx_desc(desc, 1, bmax, csum, STMMAC_RING_MODE); @@ -68,7 +71,9 @@ static unsigned int stmmac_jumbo_frm(void *p, struct sk_buff *skb, int csum) desc->des2 = dma_map_single(priv->device, skb->data + bmax, len, DMA_TO_DEVICE); - priv->tx_skbuff_dma[entry] = desc->des2; + if (dma_mapping_error(priv->device, desc->des2)) + return -1; + priv->tx_skbuff_dma[entry].buf = desc->des2; desc->des3 = desc->des2 + BUF_SIZE_4KiB; priv->hw->desc->prepare_tx_desc(desc, 0, len, csum, STMMAC_RING_MODE); @@ -77,7 +82,9 @@ static unsigned int stmmac_jumbo_frm(void *p, struct sk_buff *skb, int csum) } else { desc->des2 = dma_map_single(priv->device, skb->data, nopaged_len, DMA_TO_DEVICE); - priv->tx_skbuff_dma[entry] = desc->des2; + if (dma_mapping_error(priv->device, desc->des2)) + return -1; + priv->tx_skbuff_dma[entry].buf = desc->des2; desc->des3 = desc->des2 + BUF_SIZE_4KiB; priv->hw->desc->prepare_tx_desc(desc, 1, nopaged_len, csum, STMMAC_RING_MODE); diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h index 128a0b723a00..58097c0e2ad5 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h @@ -34,6 +34,11 @@ #include #include +struct stmmac_tx_info { + dma_addr_t buf; + bool map_as_page; +}; + struct stmmac_priv { /* Frequently used values are kept adjacent for cache effect */ struct dma_extended_desc *dma_etx ____cacheline_aligned_in_smp; @@ -45,7 +50,7 @@ struct stmmac_priv { u32 tx_count_frames; u32 tx_coal_frames; u32 tx_coal_timer; - dma_addr_t *tx_skbuff_dma; + struct stmmac_tx_info *tx_skbuff_dma; dma_addr_t dma_tx_phy; int tx_coalesce; int hwts_tx_en; diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index 03652891fcbf..df15f00b1246 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -1073,7 +1073,8 @@ static int init_dma_desc_rings(struct net_device *dev) else p = priv->dma_tx + i; p->des2 = 0; - priv->tx_skbuff_dma[i] = 0; + priv->tx_skbuff_dma[i].buf = 0; + priv->tx_skbuff_dma[i].map_as_page = false; priv->tx_skbuff[i] = NULL; } @@ -1112,17 +1113,24 @@ static void dma_free_tx_skbufs(struct stmmac_priv *priv) else p = priv->dma_tx + i; - if (priv->tx_skbuff_dma[i]) { - dma_unmap_single(priv->device, - priv->tx_skbuff_dma[i], - priv->hw->desc->get_tx_len(p), - DMA_TO_DEVICE); - priv->tx_skbuff_dma[i] = 0; + if (priv->tx_skbuff_dma[i].buf) { + if (priv->tx_skbuff_dma[i].map_as_page) + dma_unmap_page(priv->device, + priv->tx_skbuff_dma[i].buf, + priv->hw->desc->get_tx_len(p), + DMA_TO_DEVICE); + else + dma_unmap_single(priv->device, + priv->tx_skbuff_dma[i].buf, + priv->hw->desc->get_tx_len(p), + DMA_TO_DEVICE); } if (priv->tx_skbuff[i] != NULL) { dev_kfree_skb_any(priv->tx_skbuff[i]); priv->tx_skbuff[i] = NULL; + priv->tx_skbuff_dma[i].buf = 0; + priv->tx_skbuff_dma[i].map_as_page = false; } } } @@ -1143,7 +1151,8 @@ static int alloc_dma_desc_resources(struct stmmac_priv *priv) if (!priv->rx_skbuff) goto err_rx_skbuff; - priv->tx_skbuff_dma = kmalloc_array(txsize, sizeof(dma_addr_t), + priv->tx_skbuff_dma = kmalloc_array(txsize, + sizeof(*priv->tx_skbuff_dma), GFP_KERNEL); if (!priv->tx_skbuff_dma) goto err_tx_skbuff_dma; @@ -1305,12 +1314,19 @@ static void stmmac_tx_clean(struct stmmac_priv *priv) pr_debug("%s: curr %d, dirty %d\n", __func__, priv->cur_tx, priv->dirty_tx); - if (likely(priv->tx_skbuff_dma[entry])) { - dma_unmap_single(priv->device, - priv->tx_skbuff_dma[entry], - priv->hw->desc->get_tx_len(p), - DMA_TO_DEVICE); - priv->tx_skbuff_dma[entry] = 0; + if (likely(priv->tx_skbuff_dma[entry].buf)) { + if (priv->tx_skbuff_dma[entry].map_as_page) + dma_unmap_page(priv->device, + priv->tx_skbuff_dma[entry].buf, + priv->hw->desc->get_tx_len(p), + DMA_TO_DEVICE); + else + dma_unmap_single(priv->device, + priv->tx_skbuff_dma[entry].buf, + priv->hw->desc->get_tx_len(p), + DMA_TO_DEVICE); + priv->tx_skbuff_dma[entry].buf = 0; + priv->tx_skbuff_dma[entry].map_as_page = false; } priv->hw->mode->clean_desc3(priv, p); @@ -1905,12 +1921,16 @@ static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev) if (likely(!is_jumbo)) { desc->des2 = dma_map_single(priv->device, skb->data, nopaged_len, DMA_TO_DEVICE); - priv->tx_skbuff_dma[entry] = desc->des2; + if (dma_mapping_error(priv->device, desc->des2)) + goto dma_map_err; + priv->tx_skbuff_dma[entry].buf = desc->des2; priv->hw->desc->prepare_tx_desc(desc, 1, nopaged_len, csum_insertion, priv->mode); } else { desc = first; entry = priv->hw->mode->jumbo_frm(priv, skb, csum_insertion); + if (unlikely(entry < 0)) + goto dma_map_err; } for (i = 0; i < nfrags; i++) { @@ -1926,7 +1946,11 @@ static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev) desc->des2 = skb_frag_dma_map(priv->device, frag, 0, len, DMA_TO_DEVICE); - priv->tx_skbuff_dma[entry] = desc->des2; + if (dma_mapping_error(priv->device, desc->des2)) + goto dma_map_err; /* should reuse desc w/o issues */ + + priv->tx_skbuff_dma[entry].buf = desc->des2; + priv->tx_skbuff_dma[entry].map_as_page = true; priv->hw->desc->prepare_tx_desc(desc, 0, len, csum_insertion, priv->mode); wmb(); @@ -1993,7 +2017,12 @@ static netdev_tx_t stmmac_xmit(struct sk_buff *skb, struct net_device *dev) priv->hw->dma->enable_dma_transmission(priv->ioaddr); spin_unlock(&priv->tx_lock); + return NETDEV_TX_OK; +dma_map_err: + dev_err(priv->device, "Tx dma map failed\n"); + dev_kfree_skb(skb); + priv->dev->stats.tx_dropped++; return NETDEV_TX_OK; } @@ -2046,7 +2075,12 @@ static inline void stmmac_rx_refill(struct stmmac_priv *priv) priv->rx_skbuff_dma[entry] = dma_map_single(priv->device, skb->data, bfsize, DMA_FROM_DEVICE); - + if (dma_mapping_error(priv->device, + priv->rx_skbuff_dma[entry])) { + dev_err(priv->device, "Rx dma map failed\n"); + dev_kfree_skb(skb); + break; + } p->des2 = priv->rx_skbuff_dma[entry]; priv->hw->mode->refill_desc3(priv, p); -- cgit v1.2.1 From b95089d00c04712a9d4655d5c638930ac24b7bd3 Mon Sep 17 00:00:00 2001 From: Or Gerlitz Date: Wed, 27 Aug 2014 16:47:48 +0300 Subject: net/mlx4: Move the tunnel steering helper function to mlx4_core Move the function which we use to set VXLAN DMFS (flow-steering) rules from mlx4_en to mlx4_core. This refactoring will allow the mlx4_ib driver to call the helper for the use case of user-space RAW Ethernet QPs, such that they can serve VXLAN traffic too. Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/en_netdev.c | 31 ++------------------- drivers/net/ethernet/mellanox/mlx4/mcg.c | 38 ++++++++++++++++++++++++++ 2 files changed, 40 insertions(+), 29 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c index bb536aa613f4..abddcf8c40aa 100644 --- a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c +++ b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c @@ -474,39 +474,12 @@ static int mlx4_en_tunnel_steer_add(struct mlx4_en_priv *priv, unsigned char *ad int qpn, u64 *reg_id) { int err; - struct mlx4_spec_list spec_eth_outer = { {NULL} }; - struct mlx4_spec_list spec_vxlan = { {NULL} }; - struct mlx4_spec_list spec_eth_inner = { {NULL} }; - - struct mlx4_net_trans_rule rule = { - .queue_mode = MLX4_NET_TRANS_Q_FIFO, - .exclusive = 0, - .allow_loopback = 1, - .promisc_mode = MLX4_FS_REGULAR, - .priority = MLX4_DOMAIN_NIC, - }; - - __be64 mac_mask = cpu_to_be64(MLX4_MAC_MASK << 16); if (priv->mdev->dev->caps.tunnel_offload_mode != MLX4_TUNNEL_OFFLOAD_MODE_VXLAN) return 0; /* do nothing */ - rule.port = priv->port; - rule.qpn = qpn; - INIT_LIST_HEAD(&rule.list); - - spec_eth_outer.id = MLX4_NET_TRANS_RULE_ID_ETH; - memcpy(spec_eth_outer.eth.dst_mac, addr, ETH_ALEN); - memcpy(spec_eth_outer.eth.dst_mac_msk, &mac_mask, ETH_ALEN); - - spec_vxlan.id = MLX4_NET_TRANS_RULE_ID_VXLAN; /* any vxlan header */ - spec_eth_inner.id = MLX4_NET_TRANS_RULE_ID_ETH; /* any inner eth header */ - - list_add_tail(&spec_eth_outer.list, &rule.list); - list_add_tail(&spec_vxlan.list, &rule.list); - list_add_tail(&spec_eth_inner.list, &rule.list); - - err = mlx4_flow_attach(priv->mdev->dev, &rule, reg_id); + err = mlx4_tunnel_steer_add(priv->mdev->dev, addr, priv->port, qpn, + MLX4_DOMAIN_NIC, reg_id); if (err) { en_err(priv, "failed to add vxlan steering rule, err %d\n", err); return err; diff --git a/drivers/net/ethernet/mellanox/mlx4/mcg.c b/drivers/net/ethernet/mellanox/mlx4/mcg.c index d80e7a6fac74..ca0f98c95105 100644 --- a/drivers/net/ethernet/mellanox/mlx4/mcg.c +++ b/drivers/net/ethernet/mellanox/mlx4/mcg.c @@ -1020,6 +1020,44 @@ int mlx4_flow_detach(struct mlx4_dev *dev, u64 reg_id) } EXPORT_SYMBOL_GPL(mlx4_flow_detach); +int mlx4_tunnel_steer_add(struct mlx4_dev *dev, unsigned char *addr, + int port, int qpn, u16 prio, u64 *reg_id) +{ + int err; + struct mlx4_spec_list spec_eth_outer = { {NULL} }; + struct mlx4_spec_list spec_vxlan = { {NULL} }; + struct mlx4_spec_list spec_eth_inner = { {NULL} }; + + struct mlx4_net_trans_rule rule = { + .queue_mode = MLX4_NET_TRANS_Q_FIFO, + .exclusive = 0, + .allow_loopback = 1, + .promisc_mode = MLX4_FS_REGULAR, + }; + + __be64 mac_mask = cpu_to_be64(MLX4_MAC_MASK << 16); + + rule.port = port; + rule.qpn = qpn; + rule.priority = prio; + INIT_LIST_HEAD(&rule.list); + + spec_eth_outer.id = MLX4_NET_TRANS_RULE_ID_ETH; + memcpy(spec_eth_outer.eth.dst_mac, addr, ETH_ALEN); + memcpy(spec_eth_outer.eth.dst_mac_msk, &mac_mask, ETH_ALEN); + + spec_vxlan.id = MLX4_NET_TRANS_RULE_ID_VXLAN; /* any vxlan header */ + spec_eth_inner.id = MLX4_NET_TRANS_RULE_ID_ETH; /* any inner eth header */ + + list_add_tail(&spec_eth_outer.list, &rule.list); + list_add_tail(&spec_vxlan.list, &rule.list); + list_add_tail(&spec_eth_inner.list, &rule.list); + + err = mlx4_flow_attach(dev, &rule, reg_id); + return err; +} +EXPORT_SYMBOL(mlx4_tunnel_steer_add); + int mlx4_FLOW_STEERING_IB_UC_QP_RANGE(struct mlx4_dev *dev, u32 min_range_qpn, u32 max_range_qpn) { -- cgit v1.2.1 From 162fb1d6559c4dcb454f172248d6d8ffa7a30bf8 Mon Sep 17 00:00:00 2001 From: nandini sharma Date: Thu, 28 Aug 2014 08:11:41 +0200 Subject: stmmac: fix the EEE LPI Macro definitions. This patch is to fix the definition of macros for EEE otherwise the LPI TX/RX entry/exit cannot be properly managed. Signed-off-by: Nandini Sharma Signed-off-by: Giuseppe Cavallaro Signed-off-by: David S. Miller --- drivers/net/ethernet/stmicro/stmmac/common.h | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/stmicro/stmmac/common.h b/drivers/net/ethernet/stmicro/stmmac/common.h index bd54238e2df8..11702d8d2ddb 100644 --- a/drivers/net/ethernet/stmicro/stmmac/common.h +++ b/drivers/net/ethernet/stmicro/stmmac/common.h @@ -220,10 +220,10 @@ enum dma_irq_status { handle_tx = 0x8, }; -#define CORE_IRQ_TX_PATH_IN_LPI_MODE (1 << 1) -#define CORE_IRQ_TX_PATH_EXIT_LPI_MODE (1 << 2) -#define CORE_IRQ_RX_PATH_IN_LPI_MODE (1 << 3) -#define CORE_IRQ_RX_PATH_EXIT_LPI_MODE (1 << 4) +#define CORE_IRQ_TX_PATH_IN_LPI_MODE (1 << 0) +#define CORE_IRQ_TX_PATH_EXIT_LPI_MODE (1 << 1) +#define CORE_IRQ_RX_PATH_IN_LPI_MODE (1 << 2) +#define CORE_IRQ_RX_PATH_EXIT_LPI_MODE (1 << 3) #define CORE_PCS_ANE_COMPLETE (1 << 5) #define CORE_PCS_LINK_STATUS (1 << 6) -- cgit v1.2.1 From 438a62b16e0aeff5c4a5ab457343cebe4d7278da Mon Sep 17 00:00:00 2001 From: nandini sharma Date: Thu, 28 Aug 2014 08:11:42 +0200 Subject: stmmac: fix LPI TW timer value to 20.5us. The value for LPI TW timer has to be updated to 0x1E that is the hardcoded value of 20.5us and it will apply to all EEE enabled Remote PHYs. Disadvantage is for PHY's that support lesser wakeup time but we can accept it waiting to implement LLDP to negotiate the Wakeup time of Remote PHY. Signed-off-by: nandini sharma Signed-off-by: Giuseppe Cavallaro Signed-off-by: David S. Miller --- drivers/net/ethernet/stmicro/stmmac/common.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/stmicro/stmmac/common.h b/drivers/net/ethernet/stmicro/stmmac/common.h index 11702d8d2ddb..e3b81cdc94b2 100644 --- a/drivers/net/ethernet/stmicro/stmmac/common.h +++ b/drivers/net/ethernet/stmicro/stmmac/common.h @@ -287,7 +287,7 @@ struct dma_features { /* Default LPI timers */ #define STMMAC_DEFAULT_LIT_LS 0x3E8 -#define STMMAC_DEFAULT_TWT_LS 0x0 +#define STMMAC_DEFAULT_TWT_LS 0x1E #define STMMAC_CHAIN_MODE 0x1 #define STMMAC_RING_MODE 0x2 -- cgit v1.2.1 From 56b88c25c543f1d4b1fff7f1c0267f59f53c261f Mon Sep 17 00:00:00 2001 From: Giuseppe CAVALLARO Date: Thu, 28 Aug 2014 08:11:43 +0200 Subject: stmmac: never check EEE in case of a switch is attached This patch is to skip the EEE initialisation when the stmmac is using a switch (with a fixed phy support). Signed-off-by: Giuseppe Cavallaro Signed-off-by: David S. Miller --- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index df15f00b1246..3b8b57e3bd20 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -275,6 +275,7 @@ static void stmmac_eee_ctrl_timer(unsigned long arg) */ bool stmmac_eee_init(struct stmmac_priv *priv) { + char *phy_bus_name = priv->plat->phy_bus_name; bool ret = false; /* Using PCS we cannot dial with the phy registers at this stage @@ -284,6 +285,10 @@ bool stmmac_eee_init(struct stmmac_priv *priv) (priv->pcs == STMMAC_PCS_RTBI)) goto out; + /* Never init EEE in case of a switch is attached */ + if (phy_bus_name && (!strcmp(phy_bus_name, "fixed"))) + goto out; + /* MAC core supports the EEE feature. */ if (priv->dma_cap.eee) { int tx_lpi_timer = priv->tx_lpi_timer; -- cgit v1.2.1 From 71965352eedd0cc524de36accc6da7d5166a2c62 Mon Sep 17 00:00:00 2001 From: Giuseppe CAVALLARO Date: Thu, 28 Aug 2014 08:11:44 +0200 Subject: stmmac: fix PLS bit setting when EEE is active In case of PLS is active the PLS (PHY Link Status) bit in the Reg12 has to be set to allow the MAC to asserts the LPI pattern when the link is ok. Signed-off-by: nandini sharma Signed-off-by: Giuseppe Cavallaro Signed-off-by: David S. Miller --- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index 3b8b57e3bd20..3d3db16c97d4 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -321,10 +321,9 @@ bool stmmac_eee_init(struct stmmac_priv *priv) priv->hw->mac->set_eee_timer(priv->hw, STMMAC_DEFAULT_LIT_LS, tx_lpi_timer); - } else - /* Set HW EEE according to the speed */ - priv->hw->mac->set_eee_pls(priv->hw, - priv->phydev->link); + } + /* Set HW EEE according to the speed */ + priv->hw->mac->set_eee_pls(priv->hw, priv->phydev->link); pr_debug("stmmac: Energy-Efficient Ethernet initialized\n"); -- cgit v1.2.1 From e148e1bf6fcdecb19015c63ba8c6c25ed5dc3a2a Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Fri, 29 Aug 2014 18:21:41 +0200 Subject: drivers: net: NET_XGENE should depend on HAS_DMA If NO_DMA=y: drivers/built-in.o: In function `xgene_enet_delete_ring': xgene_enet_main.c:(.text+0x28755a): undefined reference to `dma_free_coherent' drivers/built-in.o: In function `xgene_enet_setup_tx_desc': xgene_enet_main.c:(.text+0x287774): undefined reference to `dma_map_single' xgene_enet_main.c:(.text+0x287780): undefined reference to `dma_mapping_error' drivers/built-in.o: In function `xgene_enet_tx_completion': xgene_enet_main.c:(.text+0x2878e6): undefined reference to `dma_unmap_single' drivers/built-in.o: In function `xgene_enet_refill_bufpool': xgene_enet_main.c:(.text+0x2879d4): undefined reference to `dma_map_single' xgene_enet_main.c:(.text+0x2879e0): undefined reference to `dma_mapping_error' drivers/built-in.o: In function `xgene_enet_rx_frame': xgene_enet_main.c:(.text+0x287aaa): undefined reference to `dma_unmap_single' drivers/built-in.o: In function `xgene_enet_free_desc_ring': xgene_enet_main.c:(.text+0x287f98): undefined reference to `dma_free_coherent' drivers/built-in.o: In function `xgene_enet_create_desc_ring': xgene_enet_main.c:(.text+0x28808e): undefined reference to `dma_alloc_coherent' drivers/built-in.o: In function `xgene_enet_probe': xgene_enet_main.c:(.text+0x2883d4): undefined reference to `dma_set_mask' xgene_enet_main.c:(.text+0x2883ec): undefined reference to `dma_supported' Signed-off-by: Geert Uytterhoeven Signed-off-by: David S. Miller --- drivers/net/ethernet/apm/xgene/Kconfig | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/apm/xgene/Kconfig b/drivers/net/ethernet/apm/xgene/Kconfig index 616dff6d3f5f..f4054d242f3c 100644 --- a/drivers/net/ethernet/apm/xgene/Kconfig +++ b/drivers/net/ethernet/apm/xgene/Kconfig @@ -1,5 +1,6 @@ config NET_XGENE tristate "APM X-Gene SoC Ethernet Driver" + depends on HAS_DMA select PHYLIB help This is the Ethernet driver for the on-chip ethernet interface on the -- cgit v1.2.1 From a9a4a2d9d622e3bde41356aa4e2694cee052d002 Mon Sep 17 00:00:00 2001 From: "Lendacky, Thomas" Date: Fri, 29 Aug 2014 13:16:50 -0500 Subject: amd-xgbe: Check for Tx hardware queue flushing support The flushing of the Tx hardware queues is only supported at a certain level of the hardware. Retrieve the current version of the hardware and use that to determine if flushing is supported. Signed-off-by: Tom Lendacky Signed-off-by: David S. Miller --- drivers/net/ethernet/amd/xgbe/xgbe-dev.c | 3 +++ drivers/net/ethernet/amd/xgbe/xgbe-drv.c | 2 ++ drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c | 7 ++++--- drivers/net/ethernet/amd/xgbe/xgbe.h | 3 +++ 4 files changed, 12 insertions(+), 3 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/amd/xgbe/xgbe-dev.c b/drivers/net/ethernet/amd/xgbe/xgbe-dev.c index edaca4496264..e43747a9926f 100644 --- a/drivers/net/ethernet/amd/xgbe/xgbe-dev.c +++ b/drivers/net/ethernet/amd/xgbe/xgbe-dev.c @@ -1633,6 +1633,9 @@ static int xgbe_flush_tx_queues(struct xgbe_prv_data *pdata) { unsigned int i, count; + if (XGMAC_GET_BITS(pdata->hw_feat.version, MAC_VR, SNPSVER) < 0x21) + return 0; + for (i = 0; i < pdata->tx_q_count; i++) XGMAC_MTL_IOWRITE_BITS(pdata, i, MTL_Q_TQOMR, FTQ, 1); diff --git a/drivers/net/ethernet/amd/xgbe/xgbe-drv.c b/drivers/net/ethernet/amd/xgbe/xgbe-drv.c index dc84f7193c2d..b26d75856553 100644 --- a/drivers/net/ethernet/amd/xgbe/xgbe-drv.c +++ b/drivers/net/ethernet/amd/xgbe/xgbe-drv.c @@ -361,6 +361,8 @@ void xgbe_get_all_hw_features(struct xgbe_prv_data *pdata) memset(hw_feat, 0, sizeof(*hw_feat)); + hw_feat->version = XGMAC_IOREAD(pdata, MAC_VR); + /* Hardware feature register 0 */ hw_feat->gmii = XGMAC_GET_BITS(mac_hfr0, MAC_HWF0R, GMIISEL); hw_feat->vlhash = XGMAC_GET_BITS(mac_hfr0, MAC_HWF0R, VLHASH); diff --git a/drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c b/drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c index a076aca138a1..46f613028e9c 100644 --- a/drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c +++ b/drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c @@ -361,15 +361,16 @@ static void xgbe_get_drvinfo(struct net_device *netdev, struct ethtool_drvinfo *drvinfo) { struct xgbe_prv_data *pdata = netdev_priv(netdev); + struct xgbe_hw_features *hw_feat = &pdata->hw_feat; strlcpy(drvinfo->driver, XGBE_DRV_NAME, sizeof(drvinfo->driver)); strlcpy(drvinfo->version, XGBE_DRV_VERSION, sizeof(drvinfo->version)); strlcpy(drvinfo->bus_info, dev_name(pdata->dev), sizeof(drvinfo->bus_info)); snprintf(drvinfo->fw_version, sizeof(drvinfo->fw_version), "%d.%d.%d", - XGMAC_IOREAD_BITS(pdata, MAC_VR, USERVER), - XGMAC_IOREAD_BITS(pdata, MAC_VR, DEVID), - XGMAC_IOREAD_BITS(pdata, MAC_VR, SNPSVER)); + XGMAC_GET_BITS(hw_feat->version, MAC_VR, USERVER), + XGMAC_GET_BITS(hw_feat->version, MAC_VR, DEVID), + XGMAC_GET_BITS(hw_feat->version, MAC_VR, SNPSVER)); drvinfo->n_stats = XGBE_STATS_COUNT; } diff --git a/drivers/net/ethernet/amd/xgbe/xgbe.h b/drivers/net/ethernet/amd/xgbe/xgbe.h index 07bf70a82908..5af5c38eef4b 100644 --- a/drivers/net/ethernet/amd/xgbe/xgbe.h +++ b/drivers/net/ethernet/amd/xgbe/xgbe.h @@ -526,6 +526,9 @@ struct xgbe_desc_if { * or configurations are present in the device. */ struct xgbe_hw_features { + /* HW Version */ + unsigned int version; + /* HW Feature Register0 */ unsigned int gmii; /* 1000 Mbps support */ unsigned int vlhash; /* VLAN Hash Filter */ -- cgit v1.2.1 From f076f453729bb7dd63a798743ee11dea039c7df3 Mon Sep 17 00:00:00 2001 From: "Lendacky, Thomas" Date: Fri, 29 Aug 2014 13:16:56 -0500 Subject: amd-xgbe: Reported fifo size from hardware is not correct The fifo size reported by the hardware is not correct. Add support to limit the reported size to what is actually present. Also, fix the argument types used in the fifo size calculation function. Signed-off-by: Tom Lendacky Signed-off-by: David S. Miller --- drivers/net/ethernet/amd/xgbe/xgbe-dev.c | 8 ++++++-- drivers/net/ethernet/amd/xgbe/xgbe.h | 1 + 2 files changed, 7 insertions(+), 2 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/amd/xgbe/xgbe-dev.c b/drivers/net/ethernet/amd/xgbe/xgbe-dev.c index e43747a9926f..acde00c8fdb4 100644 --- a/drivers/net/ethernet/amd/xgbe/xgbe-dev.c +++ b/drivers/net/ethernet/amd/xgbe/xgbe-dev.c @@ -1706,8 +1706,8 @@ static void xgbe_config_mtl_mode(struct xgbe_prv_data *pdata) XGMAC_IOWRITE_BITS(pdata, MTL_OMR, RAA, MTL_RAA_SP); } -static unsigned int xgbe_calculate_per_queue_fifo(unsigned long fifo_size, - unsigned char queue_count) +static unsigned int xgbe_calculate_per_queue_fifo(unsigned int fifo_size, + unsigned int queue_count) { unsigned int q_fifo_size = 0; enum xgbe_mtl_fifo_size p_fifo = XGMAC_MTL_FIFO_SIZE_256; @@ -1751,6 +1751,10 @@ static unsigned int xgbe_calculate_per_queue_fifo(unsigned long fifo_size, q_fifo_size = XGBE_FIFO_SIZE_KB(256); break; } + + /* The configured value is not the actual amount of fifo RAM */ + q_fifo_size = min_t(unsigned int, XGBE_FIFO_MAX, q_fifo_size); + q_fifo_size = q_fifo_size / queue_count; /* Set the queue fifo size programmable value */ diff --git a/drivers/net/ethernet/amd/xgbe/xgbe.h b/drivers/net/ethernet/amd/xgbe/xgbe.h index 5af5c38eef4b..e9fe6e6ddcc3 100644 --- a/drivers/net/ethernet/amd/xgbe/xgbe.h +++ b/drivers/net/ethernet/amd/xgbe/xgbe.h @@ -183,6 +183,7 @@ #define XGMAC_DRIVER_CONTEXT 1 #define XGMAC_IOCTL_CONTEXT 2 +#define XGBE_FIFO_MAX 81920 #define XGBE_FIFO_SIZE_B(x) (x) #define XGBE_FIFO_SIZE_KB(x) (x * 1024) -- cgit v1.2.1 From 625c8e4a2f307650fd18cf4a4f897260c800db89 Mon Sep 17 00:00:00 2001 From: "Lendacky, Thomas" Date: Fri, 29 Aug 2014 13:17:02 -0500 Subject: amd-xgbe: Fix the xpcs mmd debugfs support The debugfs support for the xpcs registers did not properly use the specified mmd (xpcs_mmd entry) which resulted in the default mmd value always being used. Update the debugfs support to generate the proper mmd register value. Signed-off-by: Tom Lendacky Signed-off-by: David S. Miller --- drivers/net/ethernet/amd/xgbe/xgbe-debugfs.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/amd/xgbe/xgbe-debugfs.c b/drivers/net/ethernet/amd/xgbe/xgbe-debugfs.c index 346592dca33c..a3c11355a34d 100644 --- a/drivers/net/ethernet/amd/xgbe/xgbe-debugfs.c +++ b/drivers/net/ethernet/amd/xgbe/xgbe-debugfs.c @@ -272,8 +272,8 @@ static ssize_t xpcs_reg_value_read(struct file *filp, char __user *buffer, struct xgbe_prv_data *pdata = filp->private_data; unsigned int value; - value = pdata->hw_if.read_mmd_regs(pdata, pdata->debugfs_xpcs_mmd, - pdata->debugfs_xpcs_reg); + value = XMDIO_READ(pdata, pdata->debugfs_xpcs_mmd, + pdata->debugfs_xpcs_reg); return xgbe_common_read(buffer, count, ppos, value); } @@ -290,8 +290,8 @@ static ssize_t xpcs_reg_value_write(struct file *filp, if (len < 0) return len; - pdata->hw_if.write_mmd_regs(pdata, pdata->debugfs_xpcs_mmd, - pdata->debugfs_xpcs_reg, value); + XMDIO_WRITE(pdata, pdata->debugfs_xpcs_mmd, pdata->debugfs_xpcs_reg, + value); return len; } -- cgit v1.2.1 From 9fc69affda1b576c0b4c2aed8acb9cf3de3349ba Mon Sep 17 00:00:00 2001 From: "Lendacky, Thomas" Date: Fri, 29 Aug 2014 13:17:08 -0500 Subject: amd-xgbe: Use the Tx queue count for Tx flow control support When configuring Tx flow control the Rx queue count was used instead of the Tx queue count for looping through the Tx hardware queues. Fix the code to use the Tx queue count. Signed-off-by: Tom Lendacky Signed-off-by: David S. Miller --- drivers/net/ethernet/amd/xgbe/xgbe-dev.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/amd/xgbe/xgbe-dev.c b/drivers/net/ethernet/amd/xgbe/xgbe-dev.c index acde00c8fdb4..6d0207eac265 100644 --- a/drivers/net/ethernet/amd/xgbe/xgbe-dev.c +++ b/drivers/net/ethernet/amd/xgbe/xgbe-dev.c @@ -348,7 +348,7 @@ static int xgbe_disable_tx_flow_control(struct xgbe_prv_data *pdata) /* Clear MAC flow control */ max_q_count = XGMAC_MAX_FLOW_CONTROL_QUEUES; - q_count = min_t(unsigned int, pdata->rx_q_count, max_q_count); + q_count = min_t(unsigned int, pdata->tx_q_count, max_q_count); reg = MAC_Q0TFCR; for (i = 0; i < q_count; i++) { reg_val = XGMAC_IOREAD(pdata, reg); @@ -373,7 +373,7 @@ static int xgbe_enable_tx_flow_control(struct xgbe_prv_data *pdata) /* Set MAC flow control */ max_q_count = XGMAC_MAX_FLOW_CONTROL_QUEUES; - q_count = min_t(unsigned int, pdata->rx_q_count, max_q_count); + q_count = min_t(unsigned int, pdata->tx_q_count, max_q_count); reg = MAC_Q0TFCR; for (i = 0; i < q_count; i++) { reg_val = XGMAC_IOREAD(pdata, reg); -- cgit v1.2.1 From d2afb5bdffde3da175b9ced66f70a4b453103d71 Mon Sep 17 00:00:00 2001 From: Giuseppe CAVALLARO Date: Mon, 1 Sep 2014 09:17:52 +0200 Subject: stmmac: fix the rx csum feature For new GMACs it is possible to turn-on/off the COE. In the current driver, when disabled the Rx-checksum via ethtool, the tool reported that csum was disabled but the HW continued to set the IPC. Indeed this is because the fix_features allows this. So the patch fixes this problem by adding the set_features. Signed-off-by: Giuseppe Cavallaro Signed-off-by: David S. Miller --- drivers/net/ethernet/stmicro/stmmac/common.h | 1 + .../net/ethernet/stmicro/stmmac/dwmac1000_core.c | 6 ++++- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 27 ++++++++++++++++++++-- 3 files changed, 31 insertions(+), 3 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/stmicro/stmmac/common.h b/drivers/net/ethernet/stmicro/stmmac/common.h index e3b81cdc94b2..593e6c4144a7 100644 --- a/drivers/net/ethernet/stmicro/stmmac/common.h +++ b/drivers/net/ethernet/stmicro/stmmac/common.h @@ -445,6 +445,7 @@ struct mac_device_info { int multicast_filter_bins; int unicast_filter_entries; int mcast_bits_log2; + unsigned int rx_csum; }; struct mac_device_info *dwmac1000_setup(void __iomem *ioaddr, int mcbins, diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c index d8ef18786a1c..5efe60ea6526 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac1000_core.c @@ -58,7 +58,11 @@ static int dwmac1000_rx_ipc_enable(struct mac_device_info *hw) void __iomem *ioaddr = hw->pcsr; u32 value = readl(ioaddr + GMAC_CONTROL); - value |= GMAC_CONTROL_IPC; + if (hw->rx_csum) + value |= GMAC_CONTROL_IPC; + else + value &= ~GMAC_CONTROL_IPC; + writel(value, ioaddr + GMAC_CONTROL); value = readl(ioaddr + GMAC_CONTROL); diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index 3d3db16c97d4..0ed8ac81238b 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -1673,6 +1673,7 @@ static int stmmac_hw_setup(struct net_device *dev) if (!ret) { pr_warn(" RX IPC Checksum Offload disabled\n"); priv->plat->rx_coe = STMMAC_RX_COE_NONE; + priv->hw->rx_csum = 0; } /* Enable the MAC Rx/Tx */ @@ -2111,7 +2112,7 @@ static int stmmac_rx(struct stmmac_priv *priv, int limit) unsigned int entry = priv->cur_rx % rxsize; unsigned int next_entry; unsigned int count = 0; - int coe = priv->plat->rx_coe; + int coe = priv->hw->rx_csum; if (netif_msg_rx_status(priv)) { pr_debug("%s: descriptor ring:\n", __func__); @@ -2334,6 +2335,7 @@ static netdev_features_t stmmac_fix_features(struct net_device *dev, features &= ~NETIF_F_RXCSUM; else if (priv->plat->rx_coe == STMMAC_RX_COE_TYPE1) features &= ~NETIF_F_IPV6_CSUM; + if (!priv->plat->tx_coe) features &= ~NETIF_F_ALL_CSUM; @@ -2348,6 +2350,24 @@ static netdev_features_t stmmac_fix_features(struct net_device *dev, return features; } +static int stmmac_set_features(struct net_device *netdev, + netdev_features_t features) +{ + struct stmmac_priv *priv = netdev_priv(netdev); + + /* Keep the COE Type in case of csum is supporting */ + if (features & NETIF_F_RXCSUM) + priv->hw->rx_csum = priv->plat->rx_coe; + else + priv->hw->rx_csum = 0; + /* No check needed because rx_coe has been set before and it will be + * fixed in case of issue. + */ + priv->hw->mac->rx_ipc(priv->hw); + + return 0; +} + /** * stmmac_interrupt - main ISR * @irq: interrupt number. @@ -2628,6 +2648,7 @@ static const struct net_device_ops stmmac_netdev_ops = { .ndo_stop = stmmac_release, .ndo_change_mtu = stmmac_change_mtu, .ndo_fix_features = stmmac_fix_features, + .ndo_set_features = stmmac_set_features, .ndo_set_rx_mode = stmmac_set_rx_mode, .ndo_tx_timeout = stmmac_tx_timeout, .ndo_do_ioctl = stmmac_ioctl, @@ -2704,9 +2725,11 @@ static int stmmac_hw_init(struct stmmac_priv *priv) /* To use alternate (extended) or normal descriptor structures */ stmmac_selec_desc_mode(priv); - if (priv->plat->rx_coe) + if (priv->plat->rx_coe) { + priv->hw->rx_csum = priv->plat->rx_coe; pr_info(" RX Checksum Offload Engine supported (type %d)\n", priv->plat->rx_coe); + } if (priv->plat->tx_coe) pr_info(" TX Checksum insertion supported\n"); -- cgit v1.2.1 From cc25f0cbe4409d6a573b1f3bf7020d5b04076ee9 Mon Sep 17 00:00:00 2001 From: Giuseppe CAVALLARO Date: Mon, 1 Sep 2014 09:17:53 +0200 Subject: stmmac: only remove RXCSUM feature if no rx coe is available In case of the HW is not able to do the receive checksum offloading the only feature to remove is NETIF_F_RXCSUM. Signed-off-by: Giuseppe Cavallaro Signed-off-by: David S. Miller --- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 2 -- 1 file changed, 2 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index 0ed8ac81238b..6e6ee226de04 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -2333,8 +2333,6 @@ static netdev_features_t stmmac_fix_features(struct net_device *dev, if (priv->plat->rx_coe == STMMAC_RX_COE_NONE) features &= ~NETIF_F_RXCSUM; - else if (priv->plat->rx_coe == STMMAC_RX_COE_TYPE1) - features &= ~NETIF_F_IPV6_CSUM; if (!priv->plat->tx_coe) features &= ~NETIF_F_ALL_CSUM; -- cgit v1.2.1 From 444018a7f1f46d588328498777cab5a9f4d29105 Mon Sep 17 00:00:00 2001 From: Hariprasad Shenai Date: Mon, 1 Sep 2014 19:54:55 +0530 Subject: cxgb4: Fix for handling 1Gb/s SFP+ Transceiver Modules We previously assumed that a Port's Capabilities and Advertised Capabilities would never change from Port Initialization time. This is no longer true when we can have 10Gb/s and 1Gb/s SFP+ Transceiver Modules randomly swapped. Signed-off-by: Hariprasad Shenai Signed-off-by: David S. Miller --- drivers/net/ethernet/chelsio/cxgb4/t4_hw.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c b/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c index a853133d8db8..6b92c4c5a241 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c +++ b/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c @@ -3742,6 +3742,7 @@ int t4_handle_fw_rpl(struct adapter *adap, const __be64 *rpl) lc->link_ok = link_ok; lc->speed = speed; lc->fc = fc; + lc->supported = be16_to_cpu(p->u.info.pcap); t4_os_link_changed(adap, port, link_ok); } if (mod != pi->mod_type) { -- cgit v1.2.1 From 63a92fe6f7e40069086be21bf9fbcfbe8d001345 Mon Sep 17 00:00:00 2001 From: Hariprasad Shenai Date: Mon, 1 Sep 2014 19:54:56 +0530 Subject: cxgb4: Fixed the code to use correct length for part number Previously it was using the length value of serial number. Also added macro for VPD unique identifier (0x82). Signed-off-by: Casey Leedom Signed-off-by: Hariprasad Shenai Signed-off-by: David S. Miller --- drivers/net/ethernet/chelsio/cxgb4/t4_hw.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c b/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c index 6b92c4c5a241..adf16a54da26 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c +++ b/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c @@ -566,6 +566,7 @@ int t4_memory_rw(struct adapter *adap, int win, int mtype, u32 addr, #define VPD_BASE 0x400 #define VPD_BASE_OLD 0 #define VPD_LEN 1024 +#define CHELSIO_VPD_UNIQUE_ID 0x82 /** * t4_seeprom_wp - enable/disable EEPROM write protection @@ -603,7 +604,14 @@ int get_vpd_params(struct adapter *adapter, struct vpd_params *p) ret = pci_read_vpd(adapter->pdev, VPD_BASE, sizeof(u32), vpd); if (ret < 0) goto out; - addr = *vpd == 0x82 ? VPD_BASE : VPD_BASE_OLD; + + /* The VPD shall have a unique identifier specified by the PCI SIG. + * For chelsio adapters, the identifier is 0x82. The first byte of a VPD + * shall be CHELSIO_VPD_UNIQUE_ID (0x82). The VPD programming software + * is expected to automatically put this entry at the + * beginning of the VPD. + */ + addr = *vpd == CHELSIO_VPD_UNIQUE_ID ? VPD_BASE : VPD_BASE_OLD; ret = pci_read_vpd(adapter->pdev, addr, VPD_LEN, vpd); if (ret < 0) @@ -667,6 +675,7 @@ int get_vpd_params(struct adapter *adapter, struct vpd_params *p) i = pci_vpd_info_field_size(vpd + sn - PCI_VPD_INFO_FLD_HDR_SIZE); memcpy(p->sn, vpd + sn, min(i, SERNUM_LEN)); strim(p->sn); + i = pci_vpd_info_field_size(vpd + pn - PCI_VPD_INFO_FLD_HDR_SIZE); memcpy(p->pn, vpd + pn, min(i, PN_LEN)); strim(p->pn); -- cgit v1.2.1 From 9bb59b96ae88ee9dc035d5cc9818b02b12208904 Mon Sep 17 00:00:00 2001 From: Hariprasad Shenai Date: Mon, 1 Sep 2014 19:54:57 +0530 Subject: cxgb4: Fix T5 adapter accessing T4 adapter registers Fixes few register access for both T4 and T5. PCIE_CORE_UTL_SYSTEM_BUS_AGENT_STATUS & PCIE_CORE_UTL_PCI_EXPRESS_PORT_STATUS is T4 only register don't let T5 access them. For T5 MA_PARITY_ERROR_STATUS2 is additionally read. MPS_TRC_RSS_CONTROL is T4 only register, for T5 use MPS_T5_TRC_RSS_CONTROL. Signed-off-by: Hariprasad Shenai Signed-off-by: David S. Miller --- drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c | 4 +++- drivers/net/ethernet/chelsio/cxgb4/t4_hw.c | 29 ++++++++++++++++--------- drivers/net/ethernet/chelsio/cxgb4/t4_regs.h | 2 ++ 3 files changed, 24 insertions(+), 11 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c index 18fb9c61d7ba..cf387ae8d7f8 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c +++ b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c @@ -1253,7 +1253,9 @@ freeout: t4_free_sge_resources(adap); goto freeout; } - t4_write_reg(adap, MPS_TRC_RSS_CONTROL, + t4_write_reg(adap, is_t4(adap->params.chip) ? + MPS_TRC_RSS_CONTROL : + MPS_T5_TRC_RSS_CONTROL, RSSCONTROL(netdev2pinfo(adap->port[0])->tx_chan) | QUEUENUMBER(s->ethrxq[0].rspq.abs_id)); return 0; diff --git a/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c b/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c index adf16a54da26..0250a9deb292 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c +++ b/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c @@ -1403,15 +1403,18 @@ static void pcie_intr_handler(struct adapter *adapter) int fat; - fat = t4_handle_intr_status(adapter, - PCIE_CORE_UTL_SYSTEM_BUS_AGENT_STATUS, - sysbus_intr_info) + - t4_handle_intr_status(adapter, - PCIE_CORE_UTL_PCI_EXPRESS_PORT_STATUS, - pcie_port_intr_info) + - t4_handle_intr_status(adapter, PCIE_INT_CAUSE, - is_t4(adapter->params.chip) ? - pcie_intr_info : t5_pcie_intr_info); + if (is_t4(adapter->params.chip)) + fat = t4_handle_intr_status(adapter, + PCIE_CORE_UTL_SYSTEM_BUS_AGENT_STATUS, + sysbus_intr_info) + + t4_handle_intr_status(adapter, + PCIE_CORE_UTL_PCI_EXPRESS_PORT_STATUS, + pcie_port_intr_info) + + t4_handle_intr_status(adapter, PCIE_INT_CAUSE, + pcie_intr_info); + else + fat = t4_handle_intr_status(adapter, PCIE_INT_CAUSE, + t5_pcie_intr_info); if (fat) t4_fatal_err(adapter); @@ -1777,10 +1780,16 @@ static void ma_intr_handler(struct adapter *adap) { u32 v, status = t4_read_reg(adap, MA_INT_CAUSE); - if (status & MEM_PERR_INT_CAUSE) + if (status & MEM_PERR_INT_CAUSE) { dev_alert(adap->pdev_dev, "MA parity error, parity status %#x\n", t4_read_reg(adap, MA_PARITY_ERROR_STATUS)); + if (is_t5(adap->params.chip)) + dev_alert(adap->pdev_dev, + "MA parity error, parity status %#x\n", + t4_read_reg(adap, + MA_PARITY_ERROR_STATUS2)); + } if (status & MEM_WRAP_INT_CAUSE) { v = t4_read_reg(adap, MA_INT_WRAP_STATUS); dev_alert(adap->pdev_dev, "MA address wrap-around error by " diff --git a/drivers/net/ethernet/chelsio/cxgb4/t4_regs.h b/drivers/net/ethernet/chelsio/cxgb4/t4_regs.h index e3146e83df20..39fb325474f7 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/t4_regs.h +++ b/drivers/net/ethernet/chelsio/cxgb4/t4_regs.h @@ -511,6 +511,7 @@ #define MEM_WRAP_CLIENT_NUM_GET(x) (((x) & MEM_WRAP_CLIENT_NUM_MASK) >> MEM_WRAP_CLIENT_NUM_SHIFT) #define MA_PCIE_FW 0x30b8 #define MA_PARITY_ERROR_STATUS 0x77f4 +#define MA_PARITY_ERROR_STATUS2 0x7804 #define MA_EXT_MEMORY1_BAR 0x7808 #define EDC_0_BASE_ADDR 0x7900 @@ -959,6 +960,7 @@ #define TRCMULTIFILTER 0x00000001U #define MPS_TRC_RSS_CONTROL 0x9808 +#define MPS_T5_TRC_RSS_CONTROL 0xa00c #define RSSCONTROL_MASK 0x00ff0000U #define RSSCONTROL_SHIFT 16 #define RSSCONTROL(x) ((x) << RSSCONTROL_SHIFT) -- cgit v1.2.1 From 31d55c2d6672430f3ef0bfd4de72c5a4f6a8bab9 Mon Sep 17 00:00:00 2001 From: Hariprasad Shenai Date: Mon, 1 Sep 2014 19:54:58 +0530 Subject: cxgb4: Detect and display firmware reported errors The adapter firmware can indicate error conditions to the host. If the firmware has indicated an error, print out the reason for the firmware error. Based on original work by Casey Leedom Signed-off-by: Hariprasad Shenai Signed-off-by: David S. Miller --- drivers/net/ethernet/chelsio/cxgb4/t4_hw.c | 38 ++++++++++++++++++++++++++- drivers/net/ethernet/chelsio/cxgb4/t4fw_api.h | 4 +++ 2 files changed, 41 insertions(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c b/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c index 0250a9deb292..41d04462b72e 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c +++ b/drivers/net/ethernet/chelsio/cxgb4/t4_hw.c @@ -167,6 +167,34 @@ void t4_hw_pci_read_cfg4(struct adapter *adap, int reg, u32 *val) t4_write_reg(adap, PCIE_CFG_SPACE_REQ, 0); } +/* + * t4_report_fw_error - report firmware error + * @adap: the adapter + * + * The adapter firmware can indicate error conditions to the host. + * If the firmware has indicated an error, print out the reason for + * the firmware error. + */ +static void t4_report_fw_error(struct adapter *adap) +{ + static const char *const reason[] = { + "Crash", /* PCIE_FW_EVAL_CRASH */ + "During Device Preparation", /* PCIE_FW_EVAL_PREP */ + "During Device Configuration", /* PCIE_FW_EVAL_CONF */ + "During Device Initialization", /* PCIE_FW_EVAL_INIT */ + "Unexpected Event", /* PCIE_FW_EVAL_UNEXPECTEDEVENT */ + "Insufficient Airflow", /* PCIE_FW_EVAL_OVERHEAT */ + "Device Shutdown", /* PCIE_FW_EVAL_DEVICESHUTDOWN */ + "Reserved", /* reserved */ + }; + u32 pcie_fw; + + pcie_fw = t4_read_reg(adap, MA_PCIE_FW); + if (pcie_fw & FW_PCIE_FW_ERR) + dev_err(adap->pdev_dev, "Firmware reports adapter error: %s\n", + reason[FW_PCIE_FW_EVAL_GET(pcie_fw)]); +} + /* * Get the reply to a mailbox command and store it in @rpl in big-endian order. */ @@ -300,6 +328,7 @@ int t4_wr_mbox_meat(struct adapter *adap, int mbox, const void *cmd, int size, dump_mbox(adap, mbox, data_reg); dev_err(adap->pdev_dev, "command %#x in mailbox %d timed out\n", *(const u8 *)cmd, mbox); + t4_report_fw_error(adap); return -ETIMEDOUT; } @@ -1533,6 +1562,9 @@ static void cim_intr_handler(struct adapter *adapter) int fat; + if (t4_read_reg(adapter, MA_PCIE_FW) & FW_PCIE_FW_ERR) + t4_report_fw_error(adapter); + fat = t4_handle_intr_status(adapter, CIM_HOST_INT_CAUSE, cim_intr_info) + t4_handle_intr_status(adapter, CIM_HOST_UPACC_INT_CAUSE, @@ -2751,12 +2783,16 @@ retry: /* * Issue the HELLO command to the firmware. If it's not successful * but indicates that we got a "busy" or "timeout" condition, retry - * the HELLO until we exhaust our retry limit. + * the HELLO until we exhaust our retry limit. If we do exceed our + * retry limit, check to see if the firmware left us any error + * information and report that if so. */ ret = t4_wr_mbox(adap, mbox, &c, sizeof(c), &c); if (ret < 0) { if ((ret == -EBUSY || ret == -ETIMEDOUT) && retries-- > 0) goto retry; + if (t4_read_reg(adap, MA_PCIE_FW) & FW_PCIE_FW_ERR) + t4_report_fw_error(adap); return ret; } diff --git a/drivers/net/ethernet/chelsio/cxgb4/t4fw_api.h b/drivers/net/ethernet/chelsio/cxgb4/t4fw_api.h index 5f2729ebadbe..3409756a85b9 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/t4fw_api.h +++ b/drivers/net/ethernet/chelsio/cxgb4/t4fw_api.h @@ -2228,6 +2228,10 @@ struct fw_debug_cmd { #define FW_PCIE_FW_MASTER(x) ((x) << FW_PCIE_FW_MASTER_SHIFT) #define FW_PCIE_FW_MASTER_GET(x) (((x) >> FW_PCIE_FW_MASTER_SHIFT) & \ FW_PCIE_FW_MASTER_MASK) +#define FW_PCIE_FW_EVAL_MASK 0x7 +#define FW_PCIE_FW_EVAL_SHIFT 24 +#define FW_PCIE_FW_EVAL_GET(x) (((x) >> FW_PCIE_FW_EVAL_SHIFT) & \ + FW_PCIE_FW_EVAL_MASK) struct fw_hdr { u8 ver; -- cgit v1.2.1 From 3d9103f80d7b1e8f0be85d87d102ba8dc1084f2d Mon Sep 17 00:00:00 2001 From: Hariprasad Shenai Date: Mon, 1 Sep 2014 19:54:59 +0530 Subject: cxgb4: Avoid dumping Write-only registers in register dump Avoid dumping MPS_RPLC_MAP_CTL for reg dumps; this is a Write-Only register. Reading this register may cause MPS TCAM corruption. Signed-off-by: Hariprasad Shenai Signed-off-by: David S. Miller --- drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c index cf387ae8d7f8..1b5020a847c7 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c +++ b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c @@ -1763,7 +1763,8 @@ static void get_regs(struct net_device *dev, struct ethtool_regs *regs, 0xd004, 0xd03c, 0xdfc0, 0xdfe0, 0xe000, 0xea7c, - 0xf000, 0x11190, + 0xf000, 0x11110, + 0x11118, 0x11190, 0x19040, 0x1906c, 0x19078, 0x19080, 0x1908c, 0x19124, @@ -1970,7 +1971,8 @@ static void get_regs(struct net_device *dev, struct ethtool_regs *regs, 0xd004, 0xd03c, 0xdfc0, 0xdfe0, 0xe000, 0x11088, - 0x1109c, 0x1117c, + 0x1109c, 0x11110, + 0x11118, 0x1117c, 0x11190, 0x11204, 0x19040, 0x1906c, 0x19078, 0x19080, -- cgit v1.2.1 From 5c937dd3f9eb999e6f4802987a674eae5718be54 Mon Sep 17 00:00:00 2001 From: Hariprasad Shenai Date: Mon, 1 Sep 2014 19:55:00 +0530 Subject: cxgb4: Issue mbox commands on correct mbox A couple of RDMA-related called to t4_query_params() were issuing mbox commands on mbox0 instead of mbox4. Signed-off-by: Hariprasad Shenai Signed-off-by: David S. Miller --- drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c index 1b5020a847c7..8c34811a1128 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c +++ b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c @@ -5959,7 +5959,8 @@ static int adap_init0(struct adapter *adap) params[3] = FW_PARAM_PFVF(CQ_END); params[4] = FW_PARAM_PFVF(OCQ_START); params[5] = FW_PARAM_PFVF(OCQ_END); - ret = t4_query_params(adap, 0, 0, 0, 6, params, val); + ret = t4_query_params(adap, adap->mbox, adap->fn, 0, 6, params, + val); if (ret < 0) goto bye; adap->vres.qp.start = val[0]; @@ -5971,7 +5972,8 @@ static int adap_init0(struct adapter *adap) params[0] = FW_PARAM_DEV(MAXORDIRD_QP); params[1] = FW_PARAM_DEV(MAXIRD_ADAPTER); - ret = t4_query_params(adap, 0, 0, 0, 2, params, val); + ret = t4_query_params(adap, adap->mbox, adap->fn, 0, 2, params, + val); if (ret < 0) { adap->params.max_ordird_qp = 8; adap->params.max_ird_adapter = 32 * adap->tids.ntids; -- cgit v1.2.1 From 0486a063b1ffce4f37ef80970689c64bf7b99e98 Mon Sep 17 00:00:00 2001 From: Ivan Vecera Date: Mon, 1 Sep 2014 14:21:57 +0200 Subject: tg3: prevent ifup/ifdown during PCI error recovery The patch fixes race conditions between PCI error recovery callbacks and potential ifup/ifdown. First, if ifup (tg3_open) is called between tg3_io_error_detected() and tg3_io_resume() then tp->timer is armed twice before expiry. Once during tg3_open() and again during tg3_io_resume(). This results in BUG at kernel/time/timer.c:945. Second, if ifdown (tg3_close) is called between tg3_io_error_detected() and tg3_io_resume() then tg3_napi_disable() is called twice without a tg3_napi_enable between. Once during tg3_io_error_detected() and again during tg3_close(). The tg3_io_resume() then hangs on rtnl_lock(). v2: Added logging messages per Prashant's request Cc: Prashant Sreedharan Cc: Michael Chan Signed-off-by: Ivan Vecera Acked-by: Prashant Sreedharan Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/tg3.c | 16 ++++++++++++++++ drivers/net/ethernet/broadcom/tg3.h | 1 + 2 files changed, 17 insertions(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c index 3ac5d23454a8..cb77ae93d89a 100644 --- a/drivers/net/ethernet/broadcom/tg3.c +++ b/drivers/net/ethernet/broadcom/tg3.c @@ -11617,6 +11617,12 @@ static int tg3_open(struct net_device *dev) struct tg3 *tp = netdev_priv(dev); int err; + if (tp->pcierr_recovery) { + netdev_err(dev, "Failed to open device. PCI error recovery " + "in progress\n"); + return -EAGAIN; + } + if (tp->fw_needed) { err = tg3_request_firmware(tp); if (tg3_asic_rev(tp) == ASIC_REV_57766) { @@ -11674,6 +11680,12 @@ static int tg3_close(struct net_device *dev) { struct tg3 *tp = netdev_priv(dev); + if (tp->pcierr_recovery) { + netdev_err(dev, "Failed to close device. PCI error recovery " + "in progress\n"); + return -EAGAIN; + } + tg3_ptp_fini(tp); tg3_stop(tp); @@ -17561,6 +17573,7 @@ static int tg3_init_one(struct pci_dev *pdev, tp->rx_mode = TG3_DEF_RX_MODE; tp->tx_mode = TG3_DEF_TX_MODE; tp->irq_sync = 1; + tp->pcierr_recovery = false; if (tg3_debug > 0) tp->msg_enable = tg3_debug; @@ -18071,6 +18084,8 @@ static pci_ers_result_t tg3_io_error_detected(struct pci_dev *pdev, rtnl_lock(); + tp->pcierr_recovery = true; + /* We probably don't have netdev yet */ if (!netdev || !netif_running(netdev)) goto done; @@ -18195,6 +18210,7 @@ static void tg3_io_resume(struct pci_dev *pdev) tg3_phy_start(tp); done: + tp->pcierr_recovery = false; rtnl_unlock(); } diff --git a/drivers/net/ethernet/broadcom/tg3.h b/drivers/net/ethernet/broadcom/tg3.h index 461accaf0aa4..31c9f8295953 100644 --- a/drivers/net/ethernet/broadcom/tg3.h +++ b/drivers/net/ethernet/broadcom/tg3.h @@ -3407,6 +3407,7 @@ struct tg3 { struct device *hwmon_dev; bool link_up; + bool pcierr_recovery; }; /* Accessor macros for chip and asic attributes -- cgit v1.2.1 From aff88a0695976596b39dcfa65da4896c802c938d Mon Sep 17 00:00:00 2001 From: Roland Stigge Date: Mon, 1 Sep 2014 13:46:46 +0200 Subject: net: lpc_eth: Fix crash on ip link up When a link is already up, the following sequence makes the kernel block completely: ip link set dev eth0 down ip link set dev eth0 up This is because on suspended phy, the following lines __lpc_eth_reset(pldat); __lpc_eth_init(pldat); make the LPC ethernet core block (see LPC32x0 manual). The PHY needs to be (re-)activated low-level first. Signed-off-by: Roland Stigge Signed-off-by: David S. Miller --- drivers/net/ethernet/nxp/lpc_eth.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/nxp/lpc_eth.c b/drivers/net/ethernet/nxp/lpc_eth.c index 8706c0dbd0c3..a44a03c45014 100644 --- a/drivers/net/ethernet/nxp/lpc_eth.c +++ b/drivers/net/ethernet/nxp/lpc_eth.c @@ -1220,6 +1220,9 @@ static int lpc_eth_open(struct net_device *ndev) __lpc_eth_clock_enable(pldat, true); + /* Suspended PHY makes LPC ethernet core block, so resume now */ + phy_resume(pldat->phy_dev); + /* Reset and initialize */ __lpc_eth_reset(pldat); __lpc_eth_init(pldat); -- cgit v1.2.1 From f6ec9c335b502d8011971d07508589d212cb3c93 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Mon, 1 Sep 2014 16:25:35 +0200 Subject: net: sh_eth: fix driver dependencies Renesas SuperH Ethernet support should be available only on Renesas ARM SoCs and SuperH architecture. Signed-off-by: Bartlomiej Zolnierkiewicz Acked-by: Kyungmin Park Cc: Simon Horman Cc: Magnus Damm Acked-by: Sergei Shtylyov Acked-by: Geert Uytterhoeven Acked-by: Simon Horman Signed-off-by: David S. Miller --- drivers/net/ethernet/renesas/Kconfig | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/renesas/Kconfig b/drivers/net/ethernet/renesas/Kconfig index 9e757c792d84..196e98a2d93b 100644 --- a/drivers/net/ethernet/renesas/Kconfig +++ b/drivers/net/ethernet/renesas/Kconfig @@ -5,6 +5,7 @@ config SH_ETH tristate "Renesas SuperH Ethernet support" depends on HAS_DMA + depends on ARCH_SHMOBILE || SUPERH || COMPILE_TEST select CRC32 select MII select MDIO_BITBANG -- cgit v1.2.1 From c24f33796830aa42c496c2b2529ce6d51533af84 Mon Sep 17 00:00:00 2001 From: Bartlomiej Zolnierkiewicz Date: Mon, 1 Sep 2014 17:39:04 +0200 Subject: net: calxedaxgmac: fix driver dependencies Calxeda 1G/10G XGMAC Ethernet support should be available only on Calxeda ECX-1000/2000 (Highbank/Midway) platforms. Signed-off-by: Bartlomiej Zolnierkiewicz Acked-by: Kyungmin Park Cc: Rob Herring Signed-off-by: David S. Miller --- drivers/net/ethernet/calxeda/Kconfig | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/calxeda/Kconfig b/drivers/net/ethernet/calxeda/Kconfig index 184a063bed5f..07d2201530d2 100644 --- a/drivers/net/ethernet/calxeda/Kconfig +++ b/drivers/net/ethernet/calxeda/Kconfig @@ -1,6 +1,7 @@ config NET_CALXEDA_XGMAC tristate "Calxeda 1G/10G XGMAC Ethernet driver" depends on HAS_IOMEM && HAS_DMA + depends on ARCH_HIGHBANK || COMPILE_TEST select CRC32 help This is the driver for the XGMAC Ethernet IP block found on Calxeda -- cgit v1.2.1 From 04860eb7d911bbd958463416cc045b69ffdf73b3 Mon Sep 17 00:00:00 2001 From: Manish Chopra Date: Tue, 2 Sep 2014 04:31:25 -0400 Subject: bnx2x: Configure device endianity on driver load and reset endianity on removal. Some hosts can be both little and big endian. In certain scenarios a big endian kernel can kexec a little endian kernel. This patch fixes this case from both ends: 1) Return endianity to original values on shutdown (in case little endian kernel boots after we shutdown). 2) Do not rely on HW reset values when loading driver in little endian kernel but configure them explicitly (in case previous kernel was big endian and did not reset the HW). Signed-off-by: Manish Chopra Signed-off-by: Ariel Elior Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c | 57 ++++++++++++++++-------- 1 file changed, 39 insertions(+), 18 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c index 900cab420810..d1c093dcb054 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c @@ -6849,6 +6849,37 @@ static void bnx2x__common_init_phy(struct bnx2x *bp) bnx2x_release_phy_lock(bp); } +static void bnx2x_config_endianity(struct bnx2x *bp, u32 val) +{ + REG_WR(bp, PXP2_REG_RQ_QM_ENDIAN_M, val); + REG_WR(bp, PXP2_REG_RQ_TM_ENDIAN_M, val); + REG_WR(bp, PXP2_REG_RQ_SRC_ENDIAN_M, val); + REG_WR(bp, PXP2_REG_RQ_CDU_ENDIAN_M, val); + REG_WR(bp, PXP2_REG_RQ_DBG_ENDIAN_M, val); + + /* make sure this value is 0 */ + REG_WR(bp, PXP2_REG_RQ_HC_ENDIAN_M, 0); + + REG_WR(bp, PXP2_REG_RD_QM_SWAP_MODE, val); + REG_WR(bp, PXP2_REG_RD_TM_SWAP_MODE, val); + REG_WR(bp, PXP2_REG_RD_SRC_SWAP_MODE, val); + REG_WR(bp, PXP2_REG_RD_CDURD_SWAP_MODE, val); +} + +static void bnx2x_set_endianity(struct bnx2x *bp) +{ +#ifdef __BIG_ENDIAN + bnx2x_config_endianity(bp, 1); +#else + bnx2x_config_endianity(bp, 0); +#endif +} + +static void bnx2x_reset_endianity(struct bnx2x *bp) +{ + bnx2x_config_endianity(bp, 0); +} + /** * bnx2x_init_hw_common - initialize the HW at the COMMON phase. * @@ -6915,23 +6946,7 @@ static int bnx2x_init_hw_common(struct bnx2x *bp) bnx2x_init_block(bp, BLOCK_PXP2, PHASE_COMMON); bnx2x_init_pxp(bp); - -#ifdef __BIG_ENDIAN - REG_WR(bp, PXP2_REG_RQ_QM_ENDIAN_M, 1); - REG_WR(bp, PXP2_REG_RQ_TM_ENDIAN_M, 1); - REG_WR(bp, PXP2_REG_RQ_SRC_ENDIAN_M, 1); - REG_WR(bp, PXP2_REG_RQ_CDU_ENDIAN_M, 1); - REG_WR(bp, PXP2_REG_RQ_DBG_ENDIAN_M, 1); - /* make sure this value is 0 */ - REG_WR(bp, PXP2_REG_RQ_HC_ENDIAN_M, 0); - -/* REG_WR(bp, PXP2_REG_RD_PBF_SWAP_MODE, 1); */ - REG_WR(bp, PXP2_REG_RD_QM_SWAP_MODE, 1); - REG_WR(bp, PXP2_REG_RD_TM_SWAP_MODE, 1); - REG_WR(bp, PXP2_REG_RD_SRC_SWAP_MODE, 1); - REG_WR(bp, PXP2_REG_RD_CDURD_SWAP_MODE, 1); -#endif - + bnx2x_set_endianity(bp); bnx2x_ilt_init_page_size(bp, INITOP_SET); if (CHIP_REV_IS_FPGA(bp) && CHIP_IS_E1H(bp)) @@ -13169,9 +13184,15 @@ static void __bnx2x_remove(struct pci_dev *pdev, bnx2x_iov_remove_one(bp); /* Power on: we can't let PCI layer write to us while we are in D3 */ - if (IS_PF(bp)) + if (IS_PF(bp)) { bnx2x_set_power_state(bp, PCI_D0); + /* Set endianity registers to reset values in case next driver + * boots in different endianty environment. + */ + bnx2x_reset_endianity(bp); + } + /* Disable MSI/MSI-X */ bnx2x_disable_msi(bp); -- cgit v1.2.1 From bec6bfb2437f4676dbaaacba6019e9dafef18962 Mon Sep 17 00:00:00 2001 From: "Lendacky, Thomas" Date: Tue, 2 Sep 2014 09:40:22 -0500 Subject: amd-xgbe: Fix initialization of the wrong spin lock During allocation and initialization of the network driver structures, the wrong pointer is used to initialize a spin lock. Fix the spin lock initialization by using the proper pointer. Signed-off-by: Tom Lendacky Signed-off-by: David S. Miller --- drivers/net/ethernet/amd/xgbe/xgbe-main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/amd/xgbe/xgbe-main.c b/drivers/net/ethernet/amd/xgbe/xgbe-main.c index 8aa6a9353f7b..bdf9cfa70e88 100644 --- a/drivers/net/ethernet/amd/xgbe/xgbe-main.c +++ b/drivers/net/ethernet/amd/xgbe/xgbe-main.c @@ -172,7 +172,7 @@ static struct xgbe_channel *xgbe_alloc_rings(struct xgbe_prv_data *pdata) } if (i < pdata->rx_ring_count) { - spin_lock_init(&tx_ring->lock); + spin_lock_init(&rx_ring->lock); channel->rx_ring = rx_ring++; } -- cgit v1.2.1 From 98ea232cf63961fad734cc8c5e07e8915ec73073 Mon Sep 17 00:00:00 2001 From: Neil Horman Date: Thu, 4 Sep 2014 06:13:38 -0400 Subject: 3c59x: avoid panic in boomerang_start_xmit when finding page address: This bug was reported on a very old kernel (RHEL6, 2.6.32-491.el6): BUG: unable to handle kernel paging request at 00800000 IP: [] nommu_map_page+0x15/0x110 *pdpt = 000000003454f001 *pde = 000000003f03d067 Oops: 0000 [#1] SMP last sysfs file: /sys/devices/system/cpu/online Modules linked in: nfsd lockd nfs_acl auth_rpcgss sunrpc exportfs p4_clockmod ipv6 ppdev parport_pc parport microcode iTCO_wdt iTCO_vendor_support 3c59x mii dcdbas serio_raw snd_intel8x0 snd_ac97_codec ac97_bus snd_seq snd_seq_device snd_pcm snd_timer snd soundcore snd_page_alloc i2c_i801 sg lpc_ich mfd_core ext4 jbd2 mbcache sr_mod cdrom sd_mod crc_t10dif pata_acpi ata_generic ata_piix radeon ttm drm_kms_helper drm i2c_algo_bit i2c_core dm_mirror dm_region_hash dm_log dm_mod [last unloaded: mperf] Pid: 4219, comm: nfsd Not tainted 2.6.32-491.el6.i686 #1 Dell Computer Corporation OptiPlex GX240 /OptiPlex GX240 EIP: 0060:[] EFLAGS: 00010246 CPU: 0 EIP is at nommu_map_page+0x15/0x110 EAX: 00000000 EBX: c0a83480 ECX: 00000000 EDX: 00800000 ESI: 00000000 EDI: f70e7860 EBP: e2d09b54 ESP: e2d09b24 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 Process nfsd (pid: 4219, ti=e2d08000 task=e2ceaaa0 task.ti=e2d08000) Stack: 00000056 00000000 0000000e c65efd38 00000020 00000296 00000206 00000206 <0> c050c850 c0a83480 e2cef154 00000001 e2d09ba8 f8fcd585 00000510 00000001 <0> 00000000 00000000 f5172200 f8fdac00 0039ef8c f5277020 f70e7860 00000510 Call Trace: [] ? page_address+0xd0/0xe0 [] ? boomerang_start_xmit+0x3b5/0x520 [3c59x] [] ? dev_hard_start_xmit+0xe5/0x400 [] ? ip6_output_finish+0x0/0xf0 [ipv6] [] ? sch_direct_xmit+0x113/0x180 [] ? nf_hook_slow+0x68/0x120 [] ? dev_queue_xmit+0x1b5/0x290 [] ? ip6_output_finish+0x6d/0xf0 [ipv6] [] ? ip6_xmit+0x3e8/0x490 [ipv6] [] ? inet6_csk_xmit+0x289/0x2f0 [ipv6] [] ? tcp_transmit_skb+0x431/0x7f0 [] ? __alloc_skb+0x4f/0x140 [] ? tcp_write_xmit+0x1c2/0xa50 [] ? __tcp_push_pending_frames+0x31/0xe0 [] ? tcp_sendpage+0x44a/0x4b0 [] ? tcp_sendpage+0x0/0x4b0 [] ? kernel_sendpage+0x4e/0x90 [] ? svc_send_common+0xc9/0x120 [sunrpc] [] ? svc_sendto+0x75/0x1f0 [sunrpc] [] ? _atomic_dec_and_lock+0x59/0x90 [] ? nfs3svc_encode_readres+0x0/0xc0 [nfsd] [] ? svc_authorise+0x2d/0x40 [sunrpc] [] ? nfs3svc_release_fhandle+0x0/0x10 [nfsd] [] ? svc_process_common+0xf1/0x5a0 [sunrpc] [] ? svc_tcp_sendto+0x36/0xa0 [sunrpc] [] ? svc_send+0x98/0xd0 [sunrpc] [] ? nfsd+0xac/0x140 [nfsd] [] ? complete+0x40/0x60 [] ? nfsd+0x0/0x140 [nfsd] [] ? kthread+0x7c/0xa0 [] ? kthread+0x0/0xa0 [] ? kernel_thread_helper+0x7/0x10 Code: 8d b6 00 00 00 00 eb f8 8d b4 26 00 00 00 00 8d bc 27 00 00 00 00 55 89 e5 83 ec 30 89 75 f8 31 f6 89 7d fc 89 c7 89 c8 89 5d f4 <8b> 1a 8b 4d 08 c1 eb 19 c1 e3 04 8b 9b c0 29 c7 c0 83 e3 fc 29 But the problem seems to still exist upstream. It seems on 32 bit kernels page_address() can reutrn a NULL value in some circumstances, and the pci_map_single api isn't prepared to handle that (on this system it results in a bogus pointer deference in nommu_map_page. The fix is pretty easy, if we convert the 3c59x driver to use the more convieient skb_frag_dma_map api we don't need to find the virtual address of the page at all, and page gets mapped to the hardware properly. Verified to fix the problem as described by the reporter. Applies to the net tree Change Notes: v2) Converted PCI_DMA_TODEVICE to DMA_TO_DEVICE. Thanks Dave! v3) Actually Run git commit after making changes to v2 :) Signed-off-by: Neil Horman CC: klassert@mathematik.tu-chemnitz.de CC: "David S. Miller" Signed-off-by: David S. Miller --- drivers/net/ethernet/3com/3c59x.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/3com/3c59x.c b/drivers/net/ethernet/3com/3c59x.c index 059c7414e303..3fe45c705933 100644 --- a/drivers/net/ethernet/3com/3c59x.c +++ b/drivers/net/ethernet/3com/3c59x.c @@ -2177,10 +2177,10 @@ boomerang_start_xmit(struct sk_buff *skb, struct net_device *dev) skb_frag_t *frag = &skb_shinfo(skb)->frags[i]; vp->tx_ring[entry].frag[i+1].addr = - cpu_to_le32(pci_map_single( - VORTEX_PCI(vp), - (void *)skb_frag_address(frag), - skb_frag_size(frag), PCI_DMA_TODEVICE)); + cpu_to_le32(skb_frag_dma_map( + &VORTEX_PCI(vp)->dev, + frag, + frag->page_offset, frag->size, DMA_TO_DEVICE)); if (i == skb_shinfo(skb)->nr_frags-1) vp->tx_ring[entry].frag[i+1].length = cpu_to_le32(skb_frag_size(frag)|LAST_FRAG); -- cgit v1.2.1 From 6e9e5644378bdeebe09db9181534a03361701f4e Mon Sep 17 00:00:00 2001 From: Yaniv Rosner Date: Thu, 4 Sep 2014 13:26:00 +0300 Subject: bnx2x: Fix link problems for 1G SFP RJ45 module When 1G SFP RJ45 module is detected, driver must reset the Tx laser in order to prevent link issues. As part of change, the link_attr_sync was relocated from vars to params. Signed-off-by: Yaniv Rosner Signed-off-by: Yuval Mintz Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h | 7 ++- drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c | 74 +++++++++++++----------- drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h | 5 +- 3 files changed, 50 insertions(+), 36 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h index 5ba8af50c84f..c4daa068f1db 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h @@ -2233,7 +2233,12 @@ struct shmem2_region { u32 reserved3; /* Offset 0x14C */ u32 reserved4; /* Offset 0x150 */ u32 link_attr_sync[PORT_MAX]; /* Offset 0x154 */ - #define LINK_ATTR_SYNC_KR2_ENABLE (1<<0) + #define LINK_ATTR_SYNC_KR2_ENABLE 0x00000001 + #define LINK_SFP_EEPROM_COMP_CODE_MASK 0x0000ff00 + #define LINK_SFP_EEPROM_COMP_CODE_SHIFT 8 + #define LINK_SFP_EEPROM_COMP_CODE_SR 0x00001000 + #define LINK_SFP_EEPROM_COMP_CODE_LR 0x00002000 + #define LINK_SFP_EEPROM_COMP_CODE_LRM 0x00004000 u32 reserved5[2]; u32 reserved6[PORT_MAX]; diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c index 53fb4fa61b40..549549eaf580 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c @@ -154,15 +154,22 @@ typedef int (*read_sfp_module_eeprom_func_p)(struct bnx2x_phy *phy, LINK_STATUS_LINK_PARTNER_ASYMMETRIC_PAUSE) #define SFP_EEPROM_CON_TYPE_ADDR 0x2 + #define SFP_EEPROM_CON_TYPE_VAL_UNKNOWN 0x0 #define SFP_EEPROM_CON_TYPE_VAL_LC 0x7 #define SFP_EEPROM_CON_TYPE_VAL_COPPER 0x21 #define SFP_EEPROM_CON_TYPE_VAL_RJ45 0x22 -#define SFP_EEPROM_COMP_CODE_ADDR 0x3 - #define SFP_EEPROM_COMP_CODE_SR_MASK (1<<4) - #define SFP_EEPROM_COMP_CODE_LR_MASK (1<<5) - #define SFP_EEPROM_COMP_CODE_LRM_MASK (1<<6) +#define SFP_EEPROM_10G_COMP_CODE_ADDR 0x3 + #define SFP_EEPROM_10G_COMP_CODE_SR_MASK (1<<4) + #define SFP_EEPROM_10G_COMP_CODE_LR_MASK (1<<5) + #define SFP_EEPROM_10G_COMP_CODE_LRM_MASK (1<<6) + +#define SFP_EEPROM_1G_COMP_CODE_ADDR 0x6 + #define SFP_EEPROM_1G_COMP_CODE_SX (1<<0) + #define SFP_EEPROM_1G_COMP_CODE_LX (1<<1) + #define SFP_EEPROM_1G_COMP_CODE_CX (1<<2) + #define SFP_EEPROM_1G_COMP_CODE_BASE_T (1<<3) #define SFP_EEPROM_FC_TX_TECH_ADDR 0x8 #define SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_PASSIVE 0x4 @@ -3633,8 +3640,8 @@ static void bnx2x_warpcore_enable_AN_KR2(struct bnx2x_phy *phy, reg_set[i].val); /* Start KR2 work-around timer which handles BCM8073 link-parner */ - vars->link_attr_sync |= LINK_ATTR_SYNC_KR2_ENABLE; - bnx2x_update_link_attr(params, vars->link_attr_sync); + params->link_attr_sync |= LINK_ATTR_SYNC_KR2_ENABLE; + bnx2x_update_link_attr(params, params->link_attr_sync); } static void bnx2x_disable_kr2(struct link_params *params, @@ -3666,8 +3673,8 @@ static void bnx2x_disable_kr2(struct link_params *params, for (i = 0; i < ARRAY_SIZE(reg_set); i++) bnx2x_cl45_write(bp, phy, reg_set[i].devad, reg_set[i].reg, reg_set[i].val); - vars->link_attr_sync &= ~LINK_ATTR_SYNC_KR2_ENABLE; - bnx2x_update_link_attr(params, vars->link_attr_sync); + params->link_attr_sync &= ~LINK_ATTR_SYNC_KR2_ENABLE; + bnx2x_update_link_attr(params, params->link_attr_sync); vars->check_kr2_recovery_cnt = CHECK_KR2_RECOVERY_CNT; } @@ -4810,7 +4817,7 @@ void bnx2x_link_status_update(struct link_params *params, ~FEATURE_CONFIG_PFC_ENABLED; if (SHMEM2_HAS(bp, link_attr_sync)) - vars->link_attr_sync = SHMEM2_RD(bp, + params->link_attr_sync = SHMEM2_RD(bp, link_attr_sync[params->port]); DP(NETIF_MSG_LINK, "link_status 0x%x phy_link_up %x int_mask 0x%x\n", @@ -8057,21 +8064,24 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy, { struct bnx2x *bp = params->bp; u32 sync_offset = 0, phy_idx, media_types; - u8 gport, val[2], check_limiting_mode = 0; + u8 val[SFP_EEPROM_FC_TX_TECH_ADDR + 1], check_limiting_mode = 0; *edc_mode = EDC_MODE_LIMITING; phy->media_type = ETH_PHY_UNSPECIFIED; /* First check for copper cable */ if (bnx2x_read_sfp_module_eeprom(phy, params, I2C_DEV_ADDR_A0, - SFP_EEPROM_CON_TYPE_ADDR, - 2, + 0, + SFP_EEPROM_FC_TX_TECH_ADDR + 1, (u8 *)val) != 0) { DP(NETIF_MSG_LINK, "Failed to read from SFP+ module EEPROM\n"); return -EINVAL; } - - switch (val[0]) { + params->link_attr_sync &= ~LINK_SFP_EEPROM_COMP_CODE_MASK; + params->link_attr_sync |= val[SFP_EEPROM_10G_COMP_CODE_ADDR] << + LINK_SFP_EEPROM_COMP_CODE_SHIFT; + bnx2x_update_link_attr(params, params->link_attr_sync); + switch (val[SFP_EEPROM_CON_TYPE_ADDR]) { case SFP_EEPROM_CON_TYPE_VAL_COPPER: { u8 copper_module_type; @@ -8079,17 +8089,7 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy, /* Check if its active cable (includes SFP+ module) * of passive cable */ - if (bnx2x_read_sfp_module_eeprom(phy, - params, - I2C_DEV_ADDR_A0, - SFP_EEPROM_FC_TX_TECH_ADDR, - 1, - &copper_module_type) != 0) { - DP(NETIF_MSG_LINK, - "Failed to read copper-cable-type" - " from SFP+ EEPROM\n"); - return -EINVAL; - } + copper_module_type = val[SFP_EEPROM_FC_TX_TECH_ADDR]; if (copper_module_type & SFP_EEPROM_FC_TX_TECH_BITMASK_COPPER_ACTIVE) { @@ -8115,16 +8115,18 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy, } break; } + case SFP_EEPROM_CON_TYPE_VAL_UNKNOWN: case SFP_EEPROM_CON_TYPE_VAL_LC: case SFP_EEPROM_CON_TYPE_VAL_RJ45: check_limiting_mode = 1; - if ((val[1] & (SFP_EEPROM_COMP_CODE_SR_MASK | - SFP_EEPROM_COMP_CODE_LR_MASK | - SFP_EEPROM_COMP_CODE_LRM_MASK)) == 0) { + if ((val[SFP_EEPROM_10G_COMP_CODE_ADDR] & + (SFP_EEPROM_10G_COMP_CODE_SR_MASK | + SFP_EEPROM_10G_COMP_CODE_LR_MASK | + SFP_EEPROM_10G_COMP_CODE_LRM_MASK)) == 0) { DP(NETIF_MSG_LINK, "1G SFP module detected\n"); - gport = params->port; phy->media_type = ETH_PHY_SFP_1G_FIBER; if (phy->req_line_speed != SPEED_1000) { + u8 gport = params->port; phy->req_line_speed = SPEED_1000; if (!CHIP_IS_E1x(bp)) { gport = BP_PATH(bp) + @@ -8134,6 +8136,12 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy, "Warning: Link speed was forced to 1000Mbps. Current SFP module in port %d is not compliant with 10G Ethernet\n", gport); } + if (val[SFP_EEPROM_1G_COMP_CODE_ADDR] & + SFP_EEPROM_1G_COMP_CODE_BASE_T) { + bnx2x_sfp_set_transmitter(params, phy, 0); + msleep(40); + bnx2x_sfp_set_transmitter(params, phy, 1); + } } else { int idx, cfg_idx = 0; DP(NETIF_MSG_LINK, "10G Optic module detected\n"); @@ -8149,7 +8157,7 @@ static int bnx2x_get_edc_mode(struct bnx2x_phy *phy, break; default: DP(NETIF_MSG_LINK, "Unable to determine module type 0x%x !!!\n", - val[0]); + val[SFP_EEPROM_CON_TYPE_ADDR]); return -EINVAL; } sync_offset = params->shmem_base + @@ -13507,7 +13515,7 @@ static void bnx2x_check_kr2_wa(struct link_params *params, sigdet = bnx2x_warpcore_get_sigdet(phy, params); if (!sigdet) { - if (!(vars->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) { + if (!(params->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) { bnx2x_kr2_recovery(params, vars, phy); DP(NETIF_MSG_LINK, "No sigdet\n"); } @@ -13525,7 +13533,7 @@ static void bnx2x_check_kr2_wa(struct link_params *params, /* CL73 has not begun yet */ if (base_page == 0) { - if (!(vars->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) { + if (!(params->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) { bnx2x_kr2_recovery(params, vars, phy); DP(NETIF_MSG_LINK, "No BP\n"); } @@ -13541,7 +13549,7 @@ static void bnx2x_check_kr2_wa(struct link_params *params, ((next_page & 0xe0) == 0x20)))); /* In case KR2 is already disabled, check if we need to re-enable it */ - if (!(vars->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) { + if (!(params->link_attr_sync & LINK_ATTR_SYNC_KR2_ENABLE)) { if (!not_kr2_device) { DP(NETIF_MSG_LINK, "BP=0x%x, NP=0x%x\n", base_page, next_page); diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h index 389f5f8cb0a3..d9cce4c3899b 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h @@ -323,6 +323,9 @@ struct link_params { #define LINK_FLAGS_INT_DISABLED (1<<0) #define PHY_INITIALIZED (1<<1) u32 lfa_base; + + /* The same definitions as the shmem2 parameter */ + u32 link_attr_sync; }; /* Output parameters */ @@ -364,8 +367,6 @@ struct link_vars { u8 rx_tx_asic_rst; u8 turn_to_run_wc_rt; u16 rsrv2; - /* The same definitions as the shmem2 parameter */ - u32 link_attr_sync; }; /***********************************************************/ -- cgit v1.2.1 From c99d667e852766afc755fa4430be64bb94e5ea1c Mon Sep 17 00:00:00 2001 From: Anish Bhatt Date: Thu, 4 Sep 2014 17:12:57 -0700 Subject: cnic : Cleanup CONFIG_IPV6 & VLAN check The cnic module needs to ensure that if ipv6 support is compiled as a module, then the cnic module cannot be compiled as built-in as it depends on ipv6. Made this check cleaner via Kconfig Use simpler IS_ENABLED for CONFIG_VLAN_8021Q check Signed-off-by: Anish Bhatt Acked-by: Michael Chan Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/Kconfig | 2 +- drivers/net/ethernet/broadcom/cnic.c | 4 ++-- 2 files changed, 3 insertions(+), 3 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/broadcom/Kconfig b/drivers/net/ethernet/broadcom/Kconfig index 7dcfb19a31c8..d8d07a818b89 100644 --- a/drivers/net/ethernet/broadcom/Kconfig +++ b/drivers/net/ethernet/broadcom/Kconfig @@ -84,7 +84,7 @@ config BNX2 config CNIC tristate "QLogic CNIC support" - depends on PCI + depends on PCI && (IPV6 || IPV6=n) select BNX2 select UIO ---help--- diff --git a/drivers/net/ethernet/broadcom/cnic.c b/drivers/net/ethernet/broadcom/cnic.c index 27861a6c7ca5..a6a9f284c8dd 100644 --- a/drivers/net/ethernet/broadcom/cnic.c +++ b/drivers/net/ethernet/broadcom/cnic.c @@ -31,7 +31,7 @@ #include #include #include -#if defined(CONFIG_VLAN_8021Q) || defined(CONFIG_VLAN_8021Q_MODULE) +#if IS_ENABLED(CONFIG_VLAN_8021Q) #define BCM_VLAN 1 #endif #include @@ -3685,7 +3685,7 @@ static int cnic_get_v4_route(struct sockaddr_in *dst_addr, static int cnic_get_v6_route(struct sockaddr_in6 *dst_addr, struct dst_entry **dst) { -#if defined(CONFIG_IPV6) || (defined(CONFIG_IPV6_MODULE) && defined(MODULE)) +#if IS_ENABLED(CONFIG_IPV6) struct flowi6 fl6; memset(&fl6, 0, sizeof(fl6)); -- cgit v1.2.1 From e1743a16a043f3d6b707730e46ba33ca931fb553 Mon Sep 17 00:00:00 2001 From: Daniel Hellstrom Date: Fri, 5 Sep 2014 13:13:48 +0200 Subject: greth: moved TX ring cleaning to NAPI rx poll func This patch does not affect the 10/100 GRETH MAC. Before all GBit GRETH TX descriptor ring cleaning was done in start_xmit(), when descriptor list became full it activated TX interrupt to start the NAPI rx poll function to do TX ring cleaning. With this patch the TX descriptor ring is always cleaned from the NAPI rx poll function, triggered via TX or RX interrupt. Otherwise we could end up in TX frames being sent but not reported to the stack being sent. On the 10/100 GRETH this is not an issue since the SKB is copied&aligned into private buffers so that the SKB can be freed directly on start_xmit() Signed-off-by: Daniel Hellstrom Signed-off-by: David S. Miller --- drivers/net/ethernet/aeroflex/greth.c | 86 +++++++++++++++++++---------------- drivers/net/ethernet/aeroflex/greth.h | 2 +- 2 files changed, 49 insertions(+), 39 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/aeroflex/greth.c b/drivers/net/ethernet/aeroflex/greth.c index 23578dfee249..3005155e412b 100644 --- a/drivers/net/ethernet/aeroflex/greth.c +++ b/drivers/net/ethernet/aeroflex/greth.c @@ -123,6 +123,12 @@ static inline void greth_enable_tx(struct greth_private *greth) GRETH_REGORIN(greth->regs->control, GRETH_TXEN); } +static inline void greth_enable_tx_and_irq(struct greth_private *greth) +{ + wmb(); /* BDs must been written to memory before enabling TX */ + GRETH_REGORIN(greth->regs->control, GRETH_TXEN | GRETH_TXI); +} + static inline void greth_disable_tx(struct greth_private *greth) { GRETH_REGANDIN(greth->regs->control, ~GRETH_TXEN); @@ -447,29 +453,30 @@ out: return err; } +static inline u16 greth_num_free_bds(u16 tx_last, u16 tx_next) +{ + if (tx_next < tx_last) + return (tx_last - tx_next) - 1; + else + return GRETH_TXBD_NUM - (tx_next - tx_last) - 1; +} static netdev_tx_t greth_start_xmit_gbit(struct sk_buff *skb, struct net_device *dev) { struct greth_private *greth = netdev_priv(dev); struct greth_bd *bdp; - u32 status = 0, dma_addr, ctrl; + u32 status, dma_addr; int curr_tx, nr_frags, i, err = NETDEV_TX_OK; unsigned long flags; + u16 tx_last; nr_frags = skb_shinfo(skb)->nr_frags; + tx_last = greth->tx_last; + rmb(); /* tx_last is updated by the poll task */ - /* Clean TX Ring */ - greth_clean_tx_gbit(dev); - - if (greth->tx_free < nr_frags + 1) { - spin_lock_irqsave(&greth->devlock, flags);/*save from poll/irq*/ - ctrl = GRETH_REGLOAD(greth->regs->control); - /* Enable TX IRQ only if not already in poll() routine */ - if (ctrl & GRETH_RXI) - GRETH_REGSAVE(greth->regs->control, ctrl | GRETH_TXI); + if (greth_num_free_bds(tx_last, greth->tx_next) < nr_frags + 1) { netif_stop_queue(dev); - spin_unlock_irqrestore(&greth->devlock, flags); err = NETDEV_TX_BUSY; goto out; } @@ -488,6 +495,8 @@ greth_start_xmit_gbit(struct sk_buff *skb, struct net_device *dev) /* Linear buf */ if (nr_frags != 0) status = GRETH_TXBD_MORE; + else + status = GRETH_BD_IE; if (skb->ip_summed == CHECKSUM_PARTIAL) status |= GRETH_TXBD_CSALL; @@ -545,14 +554,12 @@ greth_start_xmit_gbit(struct sk_buff *skb, struct net_device *dev) /* Enable the descriptor chain by enabling the first descriptor */ bdp = greth->tx_bd_base + greth->tx_next; - greth_write_bd(&bdp->stat, greth_read_bd(&bdp->stat) | GRETH_BD_EN); - greth->tx_next = curr_tx; - greth->tx_free -= nr_frags + 1; - - wmb(); + greth_write_bd(&bdp->stat, + greth_read_bd(&bdp->stat) | GRETH_BD_EN); spin_lock_irqsave(&greth->devlock, flags); /*save from poll/irq*/ - greth_enable_tx(greth); + greth->tx_next = curr_tx; + greth_enable_tx_and_irq(greth); spin_unlock_irqrestore(&greth->devlock, flags); return NETDEV_TX_OK; @@ -648,7 +655,6 @@ static void greth_clean_tx(struct net_device *dev) if (greth->tx_free > 0) { netif_wake_queue(dev); } - } static inline void greth_update_tx_stats(struct net_device *dev, u32 stat) @@ -670,20 +676,22 @@ static void greth_clean_tx_gbit(struct net_device *dev) { struct greth_private *greth; struct greth_bd *bdp, *bdp_last_frag; - struct sk_buff *skb; + struct sk_buff *skb = NULL; u32 stat; int nr_frags, i; + u16 tx_last; greth = netdev_priv(dev); + tx_last = greth->tx_last; - while (greth->tx_free < GRETH_TXBD_NUM) { + while (tx_last != greth->tx_next) { - skb = greth->tx_skbuff[greth->tx_last]; + skb = greth->tx_skbuff[tx_last]; nr_frags = skb_shinfo(skb)->nr_frags; /* We only clean fully completed SKBs */ - bdp_last_frag = greth->tx_bd_base + SKIP_TX(greth->tx_last, nr_frags); + bdp_last_frag = greth->tx_bd_base + SKIP_TX(tx_last, nr_frags); GRETH_REGSAVE(greth->regs->status, GRETH_INT_TE | GRETH_INT_TX); mb(); @@ -692,14 +700,14 @@ static void greth_clean_tx_gbit(struct net_device *dev) if (stat & GRETH_BD_EN) break; - greth->tx_skbuff[greth->tx_last] = NULL; + greth->tx_skbuff[tx_last] = NULL; greth_update_tx_stats(dev, stat); dev->stats.tx_bytes += skb->len; - bdp = greth->tx_bd_base + greth->tx_last; + bdp = greth->tx_bd_base + tx_last; - greth->tx_last = NEXT_TX(greth->tx_last); + tx_last = NEXT_TX(tx_last); dma_unmap_single(greth->dev, greth_read_bd(&bdp->addr), @@ -708,21 +716,26 @@ static void greth_clean_tx_gbit(struct net_device *dev) for (i = 0; i < nr_frags; i++) { skb_frag_t *frag = &skb_shinfo(skb)->frags[i]; - bdp = greth->tx_bd_base + greth->tx_last; + bdp = greth->tx_bd_base + tx_last; dma_unmap_page(greth->dev, greth_read_bd(&bdp->addr), skb_frag_size(frag), DMA_TO_DEVICE); - greth->tx_last = NEXT_TX(greth->tx_last); + tx_last = NEXT_TX(tx_last); } - greth->tx_free += nr_frags+1; dev_kfree_skb(skb); } + if (skb) { /* skb is set only if the above while loop was entered */ + wmb(); + greth->tx_last = tx_last; - if (netif_queue_stopped(dev) && (greth->tx_free > (MAX_SKB_FRAGS+1))) - netif_wake_queue(dev); + if (netif_queue_stopped(dev) && + (greth_num_free_bds(tx_last, greth->tx_next) > + (MAX_SKB_FRAGS+1))) + netif_wake_queue(dev); + } } static int greth_rx(struct net_device *dev, int limit) @@ -965,16 +978,12 @@ static int greth_poll(struct napi_struct *napi, int budget) greth = container_of(napi, struct greth_private, napi); restart_txrx_poll: - if (netif_queue_stopped(greth->netdev)) { - if (greth->gbit_mac) - greth_clean_tx_gbit(greth->netdev); - else - greth_clean_tx(greth->netdev); - } - if (greth->gbit_mac) { + greth_clean_tx_gbit(greth->netdev); work_done += greth_rx_gbit(greth->netdev, budget - work_done); } else { + if (netif_queue_stopped(greth->netdev)) + greth_clean_tx(greth->netdev); work_done += greth_rx(greth->netdev, budget - work_done); } @@ -983,7 +992,8 @@ restart_txrx_poll: spin_lock_irqsave(&greth->devlock, flags); ctrl = GRETH_REGLOAD(greth->regs->control); - if (netif_queue_stopped(greth->netdev)) { + if ((greth->gbit_mac && (greth->tx_last != greth->tx_next)) || + (!greth->gbit_mac && netif_queue_stopped(greth->netdev))) { GRETH_REGSAVE(greth->regs->control, ctrl | GRETH_TXI | GRETH_RXI); mask = GRETH_INT_RX | GRETH_INT_RE | diff --git a/drivers/net/ethernet/aeroflex/greth.h b/drivers/net/ethernet/aeroflex/greth.h index 232a622a85b7..ae16ac94daf8 100644 --- a/drivers/net/ethernet/aeroflex/greth.h +++ b/drivers/net/ethernet/aeroflex/greth.h @@ -107,7 +107,7 @@ struct greth_private { u16 tx_next; u16 tx_last; - u16 tx_free; + u16 tx_free; /* only used on 10/100Mbit */ u16 rx_cur; struct greth_regs *regs; /* Address of controller registers. */ -- cgit v1.2.1 From 6026510896adfa0db5ed76a6d6d1cd1602b29208 Mon Sep 17 00:00:00 2001 From: "Lendacky, Thomas" Date: Fri, 5 Sep 2014 18:02:30 -0500 Subject: amd-xgbe: Treat certain counter registers as 64 bit Even if the management counters are configured to be 32 bit register values, the [rt]xoctetcount_gb and [rt]xoctetcount_g counters are always 64 bit counter registers. Since they are not being treated as 64 bit values, these statistics are being reported incorrectly (ifconfig, ethtool, etc.). Update the routines used to read the registers to access the "hi" register (an offset of 4 from the "lo" register) to create a 64 bit value for these 64 bit counters. Signed-off-by: Tom Lendacky Signed-off-by: David S. Miller --- drivers/net/ethernet/amd/xgbe/xgbe-dev.c | 190 ++++++++++++++++++------------- 1 file changed, 108 insertions(+), 82 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/amd/xgbe/xgbe-dev.c b/drivers/net/ethernet/amd/xgbe/xgbe-dev.c index 6d0207eac265..f3d04f19ebd4 100644 --- a/drivers/net/ethernet/amd/xgbe/xgbe-dev.c +++ b/drivers/net/ethernet/amd/xgbe/xgbe-dev.c @@ -1954,6 +1954,32 @@ static void xgbe_config_vlan_support(struct xgbe_prv_data *pdata) xgbe_disable_rx_vlan_stripping(pdata); } +static u64 xgbe_mmc_read(struct xgbe_prv_data *pdata, unsigned int reg_lo) +{ + bool read_hi; + u64 val; + + switch (reg_lo) { + /* These registers are always 64 bit */ + case MMC_TXOCTETCOUNT_GB_LO: + case MMC_TXOCTETCOUNT_G_LO: + case MMC_RXOCTETCOUNT_GB_LO: + case MMC_RXOCTETCOUNT_G_LO: + read_hi = true; + break; + + default: + read_hi = false; + }; + + val = XGMAC_IOREAD(pdata, reg_lo); + + if (read_hi) + val |= ((u64)XGMAC_IOREAD(pdata, reg_lo + 4) << 32); + + return val; +} + static void xgbe_tx_mmc_int(struct xgbe_prv_data *pdata) { struct xgbe_mmc_stats *stats = &pdata->mmc_stats; @@ -1961,75 +1987,75 @@ static void xgbe_tx_mmc_int(struct xgbe_prv_data *pdata) if (XGMAC_GET_BITS(mmc_isr, MMC_TISR, TXOCTETCOUNT_GB)) stats->txoctetcount_gb += - XGMAC_IOREAD(pdata, MMC_TXOCTETCOUNT_GB_LO); + xgbe_mmc_read(pdata, MMC_TXOCTETCOUNT_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_TISR, TXFRAMECOUNT_GB)) stats->txframecount_gb += - XGMAC_IOREAD(pdata, MMC_TXFRAMECOUNT_GB_LO); + xgbe_mmc_read(pdata, MMC_TXFRAMECOUNT_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_TISR, TXBROADCASTFRAMES_G)) stats->txbroadcastframes_g += - XGMAC_IOREAD(pdata, MMC_TXBROADCASTFRAMES_G_LO); + xgbe_mmc_read(pdata, MMC_TXBROADCASTFRAMES_G_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_TISR, TXMULTICASTFRAMES_G)) stats->txmulticastframes_g += - XGMAC_IOREAD(pdata, MMC_TXMULTICASTFRAMES_G_LO); + xgbe_mmc_read(pdata, MMC_TXMULTICASTFRAMES_G_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_TISR, TX64OCTETS_GB)) stats->tx64octets_gb += - XGMAC_IOREAD(pdata, MMC_TX64OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_TX64OCTETS_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_TISR, TX65TO127OCTETS_GB)) stats->tx65to127octets_gb += - XGMAC_IOREAD(pdata, MMC_TX65TO127OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_TX65TO127OCTETS_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_TISR, TX128TO255OCTETS_GB)) stats->tx128to255octets_gb += - XGMAC_IOREAD(pdata, MMC_TX128TO255OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_TX128TO255OCTETS_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_TISR, TX256TO511OCTETS_GB)) stats->tx256to511octets_gb += - XGMAC_IOREAD(pdata, MMC_TX256TO511OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_TX256TO511OCTETS_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_TISR, TX512TO1023OCTETS_GB)) stats->tx512to1023octets_gb += - XGMAC_IOREAD(pdata, MMC_TX512TO1023OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_TX512TO1023OCTETS_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_TISR, TX1024TOMAXOCTETS_GB)) stats->tx1024tomaxoctets_gb += - XGMAC_IOREAD(pdata, MMC_TX1024TOMAXOCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_TX1024TOMAXOCTETS_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_TISR, TXUNICASTFRAMES_GB)) stats->txunicastframes_gb += - XGMAC_IOREAD(pdata, MMC_TXUNICASTFRAMES_GB_LO); + xgbe_mmc_read(pdata, MMC_TXUNICASTFRAMES_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_TISR, TXMULTICASTFRAMES_GB)) stats->txmulticastframes_gb += - XGMAC_IOREAD(pdata, MMC_TXMULTICASTFRAMES_GB_LO); + xgbe_mmc_read(pdata, MMC_TXMULTICASTFRAMES_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_TISR, TXBROADCASTFRAMES_GB)) stats->txbroadcastframes_g += - XGMAC_IOREAD(pdata, MMC_TXBROADCASTFRAMES_GB_LO); + xgbe_mmc_read(pdata, MMC_TXBROADCASTFRAMES_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_TISR, TXUNDERFLOWERROR)) stats->txunderflowerror += - XGMAC_IOREAD(pdata, MMC_TXUNDERFLOWERROR_LO); + xgbe_mmc_read(pdata, MMC_TXUNDERFLOWERROR_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_TISR, TXOCTETCOUNT_G)) stats->txoctetcount_g += - XGMAC_IOREAD(pdata, MMC_TXOCTETCOUNT_G_LO); + xgbe_mmc_read(pdata, MMC_TXOCTETCOUNT_G_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_TISR, TXFRAMECOUNT_G)) stats->txframecount_g += - XGMAC_IOREAD(pdata, MMC_TXFRAMECOUNT_G_LO); + xgbe_mmc_read(pdata, MMC_TXFRAMECOUNT_G_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_TISR, TXPAUSEFRAMES)) stats->txpauseframes += - XGMAC_IOREAD(pdata, MMC_TXPAUSEFRAMES_LO); + xgbe_mmc_read(pdata, MMC_TXPAUSEFRAMES_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_TISR, TXVLANFRAMES_G)) stats->txvlanframes_g += - XGMAC_IOREAD(pdata, MMC_TXVLANFRAMES_G_LO); + xgbe_mmc_read(pdata, MMC_TXVLANFRAMES_G_LO); } static void xgbe_rx_mmc_int(struct xgbe_prv_data *pdata) @@ -2039,95 +2065,95 @@ static void xgbe_rx_mmc_int(struct xgbe_prv_data *pdata) if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RXFRAMECOUNT_GB)) stats->rxframecount_gb += - XGMAC_IOREAD(pdata, MMC_RXFRAMECOUNT_GB_LO); + xgbe_mmc_read(pdata, MMC_RXFRAMECOUNT_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RXOCTETCOUNT_GB)) stats->rxoctetcount_gb += - XGMAC_IOREAD(pdata, MMC_RXOCTETCOUNT_GB_LO); + xgbe_mmc_read(pdata, MMC_RXOCTETCOUNT_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RXOCTETCOUNT_G)) stats->rxoctetcount_g += - XGMAC_IOREAD(pdata, MMC_RXOCTETCOUNT_G_LO); + xgbe_mmc_read(pdata, MMC_RXOCTETCOUNT_G_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RXBROADCASTFRAMES_G)) stats->rxbroadcastframes_g += - XGMAC_IOREAD(pdata, MMC_RXBROADCASTFRAMES_G_LO); + xgbe_mmc_read(pdata, MMC_RXBROADCASTFRAMES_G_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RXMULTICASTFRAMES_G)) stats->rxmulticastframes_g += - XGMAC_IOREAD(pdata, MMC_RXMULTICASTFRAMES_G_LO); + xgbe_mmc_read(pdata, MMC_RXMULTICASTFRAMES_G_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RXCRCERROR)) stats->rxcrcerror += - XGMAC_IOREAD(pdata, MMC_RXCRCERROR_LO); + xgbe_mmc_read(pdata, MMC_RXCRCERROR_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RXRUNTERROR)) stats->rxrunterror += - XGMAC_IOREAD(pdata, MMC_RXRUNTERROR); + xgbe_mmc_read(pdata, MMC_RXRUNTERROR); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RXJABBERERROR)) stats->rxjabbererror += - XGMAC_IOREAD(pdata, MMC_RXJABBERERROR); + xgbe_mmc_read(pdata, MMC_RXJABBERERROR); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RXUNDERSIZE_G)) stats->rxundersize_g += - XGMAC_IOREAD(pdata, MMC_RXUNDERSIZE_G); + xgbe_mmc_read(pdata, MMC_RXUNDERSIZE_G); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RXOVERSIZE_G)) stats->rxoversize_g += - XGMAC_IOREAD(pdata, MMC_RXOVERSIZE_G); + xgbe_mmc_read(pdata, MMC_RXOVERSIZE_G); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RX64OCTETS_GB)) stats->rx64octets_gb += - XGMAC_IOREAD(pdata, MMC_RX64OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_RX64OCTETS_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RX65TO127OCTETS_GB)) stats->rx65to127octets_gb += - XGMAC_IOREAD(pdata, MMC_RX65TO127OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_RX65TO127OCTETS_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RX128TO255OCTETS_GB)) stats->rx128to255octets_gb += - XGMAC_IOREAD(pdata, MMC_RX128TO255OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_RX128TO255OCTETS_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RX256TO511OCTETS_GB)) stats->rx256to511octets_gb += - XGMAC_IOREAD(pdata, MMC_RX256TO511OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_RX256TO511OCTETS_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RX512TO1023OCTETS_GB)) stats->rx512to1023octets_gb += - XGMAC_IOREAD(pdata, MMC_RX512TO1023OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_RX512TO1023OCTETS_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RX1024TOMAXOCTETS_GB)) stats->rx1024tomaxoctets_gb += - XGMAC_IOREAD(pdata, MMC_RX1024TOMAXOCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_RX1024TOMAXOCTETS_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RXUNICASTFRAMES_G)) stats->rxunicastframes_g += - XGMAC_IOREAD(pdata, MMC_RXUNICASTFRAMES_G_LO); + xgbe_mmc_read(pdata, MMC_RXUNICASTFRAMES_G_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RXLENGTHERROR)) stats->rxlengtherror += - XGMAC_IOREAD(pdata, MMC_RXLENGTHERROR_LO); + xgbe_mmc_read(pdata, MMC_RXLENGTHERROR_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RXOUTOFRANGETYPE)) stats->rxoutofrangetype += - XGMAC_IOREAD(pdata, MMC_RXOUTOFRANGETYPE_LO); + xgbe_mmc_read(pdata, MMC_RXOUTOFRANGETYPE_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RXPAUSEFRAMES)) stats->rxpauseframes += - XGMAC_IOREAD(pdata, MMC_RXPAUSEFRAMES_LO); + xgbe_mmc_read(pdata, MMC_RXPAUSEFRAMES_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RXFIFOOVERFLOW)) stats->rxfifooverflow += - XGMAC_IOREAD(pdata, MMC_RXFIFOOVERFLOW_LO); + xgbe_mmc_read(pdata, MMC_RXFIFOOVERFLOW_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RXVLANFRAMES_GB)) stats->rxvlanframes_gb += - XGMAC_IOREAD(pdata, MMC_RXVLANFRAMES_GB_LO); + xgbe_mmc_read(pdata, MMC_RXVLANFRAMES_GB_LO); if (XGMAC_GET_BITS(mmc_isr, MMC_RISR, RXWATCHDOGERROR)) stats->rxwatchdogerror += - XGMAC_IOREAD(pdata, MMC_RXWATCHDOGERROR); + xgbe_mmc_read(pdata, MMC_RXWATCHDOGERROR); } static void xgbe_read_mmc_stats(struct xgbe_prv_data *pdata) @@ -2138,127 +2164,127 @@ static void xgbe_read_mmc_stats(struct xgbe_prv_data *pdata) XGMAC_IOWRITE_BITS(pdata, MMC_CR, MCF, 1); stats->txoctetcount_gb += - XGMAC_IOREAD(pdata, MMC_TXOCTETCOUNT_GB_LO); + xgbe_mmc_read(pdata, MMC_TXOCTETCOUNT_GB_LO); stats->txframecount_gb += - XGMAC_IOREAD(pdata, MMC_TXFRAMECOUNT_GB_LO); + xgbe_mmc_read(pdata, MMC_TXFRAMECOUNT_GB_LO); stats->txbroadcastframes_g += - XGMAC_IOREAD(pdata, MMC_TXBROADCASTFRAMES_G_LO); + xgbe_mmc_read(pdata, MMC_TXBROADCASTFRAMES_G_LO); stats->txmulticastframes_g += - XGMAC_IOREAD(pdata, MMC_TXMULTICASTFRAMES_G_LO); + xgbe_mmc_read(pdata, MMC_TXMULTICASTFRAMES_G_LO); stats->tx64octets_gb += - XGMAC_IOREAD(pdata, MMC_TX64OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_TX64OCTETS_GB_LO); stats->tx65to127octets_gb += - XGMAC_IOREAD(pdata, MMC_TX65TO127OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_TX65TO127OCTETS_GB_LO); stats->tx128to255octets_gb += - XGMAC_IOREAD(pdata, MMC_TX128TO255OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_TX128TO255OCTETS_GB_LO); stats->tx256to511octets_gb += - XGMAC_IOREAD(pdata, MMC_TX256TO511OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_TX256TO511OCTETS_GB_LO); stats->tx512to1023octets_gb += - XGMAC_IOREAD(pdata, MMC_TX512TO1023OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_TX512TO1023OCTETS_GB_LO); stats->tx1024tomaxoctets_gb += - XGMAC_IOREAD(pdata, MMC_TX1024TOMAXOCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_TX1024TOMAXOCTETS_GB_LO); stats->txunicastframes_gb += - XGMAC_IOREAD(pdata, MMC_TXUNICASTFRAMES_GB_LO); + xgbe_mmc_read(pdata, MMC_TXUNICASTFRAMES_GB_LO); stats->txmulticastframes_gb += - XGMAC_IOREAD(pdata, MMC_TXMULTICASTFRAMES_GB_LO); + xgbe_mmc_read(pdata, MMC_TXMULTICASTFRAMES_GB_LO); stats->txbroadcastframes_g += - XGMAC_IOREAD(pdata, MMC_TXBROADCASTFRAMES_GB_LO); + xgbe_mmc_read(pdata, MMC_TXBROADCASTFRAMES_GB_LO); stats->txunderflowerror += - XGMAC_IOREAD(pdata, MMC_TXUNDERFLOWERROR_LO); + xgbe_mmc_read(pdata, MMC_TXUNDERFLOWERROR_LO); stats->txoctetcount_g += - XGMAC_IOREAD(pdata, MMC_TXOCTETCOUNT_G_LO); + xgbe_mmc_read(pdata, MMC_TXOCTETCOUNT_G_LO); stats->txframecount_g += - XGMAC_IOREAD(pdata, MMC_TXFRAMECOUNT_G_LO); + xgbe_mmc_read(pdata, MMC_TXFRAMECOUNT_G_LO); stats->txpauseframes += - XGMAC_IOREAD(pdata, MMC_TXPAUSEFRAMES_LO); + xgbe_mmc_read(pdata, MMC_TXPAUSEFRAMES_LO); stats->txvlanframes_g += - XGMAC_IOREAD(pdata, MMC_TXVLANFRAMES_G_LO); + xgbe_mmc_read(pdata, MMC_TXVLANFRAMES_G_LO); stats->rxframecount_gb += - XGMAC_IOREAD(pdata, MMC_RXFRAMECOUNT_GB_LO); + xgbe_mmc_read(pdata, MMC_RXFRAMECOUNT_GB_LO); stats->rxoctetcount_gb += - XGMAC_IOREAD(pdata, MMC_RXOCTETCOUNT_GB_LO); + xgbe_mmc_read(pdata, MMC_RXOCTETCOUNT_GB_LO); stats->rxoctetcount_g += - XGMAC_IOREAD(pdata, MMC_RXOCTETCOUNT_G_LO); + xgbe_mmc_read(pdata, MMC_RXOCTETCOUNT_G_LO); stats->rxbroadcastframes_g += - XGMAC_IOREAD(pdata, MMC_RXBROADCASTFRAMES_G_LO); + xgbe_mmc_read(pdata, MMC_RXBROADCASTFRAMES_G_LO); stats->rxmulticastframes_g += - XGMAC_IOREAD(pdata, MMC_RXMULTICASTFRAMES_G_LO); + xgbe_mmc_read(pdata, MMC_RXMULTICASTFRAMES_G_LO); stats->rxcrcerror += - XGMAC_IOREAD(pdata, MMC_RXCRCERROR_LO); + xgbe_mmc_read(pdata, MMC_RXCRCERROR_LO); stats->rxrunterror += - XGMAC_IOREAD(pdata, MMC_RXRUNTERROR); + xgbe_mmc_read(pdata, MMC_RXRUNTERROR); stats->rxjabbererror += - XGMAC_IOREAD(pdata, MMC_RXJABBERERROR); + xgbe_mmc_read(pdata, MMC_RXJABBERERROR); stats->rxundersize_g += - XGMAC_IOREAD(pdata, MMC_RXUNDERSIZE_G); + xgbe_mmc_read(pdata, MMC_RXUNDERSIZE_G); stats->rxoversize_g += - XGMAC_IOREAD(pdata, MMC_RXOVERSIZE_G); + xgbe_mmc_read(pdata, MMC_RXOVERSIZE_G); stats->rx64octets_gb += - XGMAC_IOREAD(pdata, MMC_RX64OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_RX64OCTETS_GB_LO); stats->rx65to127octets_gb += - XGMAC_IOREAD(pdata, MMC_RX65TO127OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_RX65TO127OCTETS_GB_LO); stats->rx128to255octets_gb += - XGMAC_IOREAD(pdata, MMC_RX128TO255OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_RX128TO255OCTETS_GB_LO); stats->rx256to511octets_gb += - XGMAC_IOREAD(pdata, MMC_RX256TO511OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_RX256TO511OCTETS_GB_LO); stats->rx512to1023octets_gb += - XGMAC_IOREAD(pdata, MMC_RX512TO1023OCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_RX512TO1023OCTETS_GB_LO); stats->rx1024tomaxoctets_gb += - XGMAC_IOREAD(pdata, MMC_RX1024TOMAXOCTETS_GB_LO); + xgbe_mmc_read(pdata, MMC_RX1024TOMAXOCTETS_GB_LO); stats->rxunicastframes_g += - XGMAC_IOREAD(pdata, MMC_RXUNICASTFRAMES_G_LO); + xgbe_mmc_read(pdata, MMC_RXUNICASTFRAMES_G_LO); stats->rxlengtherror += - XGMAC_IOREAD(pdata, MMC_RXLENGTHERROR_LO); + xgbe_mmc_read(pdata, MMC_RXLENGTHERROR_LO); stats->rxoutofrangetype += - XGMAC_IOREAD(pdata, MMC_RXOUTOFRANGETYPE_LO); + xgbe_mmc_read(pdata, MMC_RXOUTOFRANGETYPE_LO); stats->rxpauseframes += - XGMAC_IOREAD(pdata, MMC_RXPAUSEFRAMES_LO); + xgbe_mmc_read(pdata, MMC_RXPAUSEFRAMES_LO); stats->rxfifooverflow += - XGMAC_IOREAD(pdata, MMC_RXFIFOOVERFLOW_LO); + xgbe_mmc_read(pdata, MMC_RXFIFOOVERFLOW_LO); stats->rxvlanframes_gb += - XGMAC_IOREAD(pdata, MMC_RXVLANFRAMES_GB_LO); + xgbe_mmc_read(pdata, MMC_RXVLANFRAMES_GB_LO); stats->rxwatchdogerror += - XGMAC_IOREAD(pdata, MMC_RXWATCHDOGERROR); + xgbe_mmc_read(pdata, MMC_RXWATCHDOGERROR); /* Un-freeze counters */ XGMAC_IOWRITE_BITS(pdata, MMC_CR, MCF, 0); -- cgit v1.2.1 From a3ba7c989d7c80b34401c58269c5903a1da8412a Mon Sep 17 00:00:00 2001 From: "Lendacky, Thomas" Date: Fri, 5 Sep 2014 18:02:36 -0500 Subject: amd-xgbe: Enable interrupts for all management counters As the management counters reach a threshold they will generate an interrupt so the value can be saved and the counter reset. The current code does not enable this interrupt on all counters. This can result in inaccurate statistics. Update the code to enable all the counters to generate an interrupt when its threshold is exceeded. Signed-off-by: Tom Lendacky Signed-off-by: David S. Miller --- drivers/net/ethernet/amd/xgbe/xgbe-dev.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/amd/xgbe/xgbe-dev.c b/drivers/net/ethernet/amd/xgbe/xgbe-dev.c index f3d04f19ebd4..ea273836d999 100644 --- a/drivers/net/ethernet/amd/xgbe/xgbe-dev.c +++ b/drivers/net/ethernet/amd/xgbe/xgbe-dev.c @@ -509,8 +509,8 @@ static void xgbe_enable_mac_interrupts(struct xgbe_prv_data *pdata) XGMAC_IOWRITE(pdata, MAC_IER, mac_ier); /* Enable all counter interrupts */ - XGMAC_IOWRITE_BITS(pdata, MMC_RIER, ALL_INTERRUPTS, 0xff); - XGMAC_IOWRITE_BITS(pdata, MMC_TIER, ALL_INTERRUPTS, 0xff); + XGMAC_IOWRITE_BITS(pdata, MMC_RIER, ALL_INTERRUPTS, 0xffffffff); + XGMAC_IOWRITE_BITS(pdata, MMC_TIER, ALL_INTERRUPTS, 0xffffffff); } static int xgbe_set_gmii_speed(struct xgbe_prv_data *pdata) -- cgit v1.2.1 From 78dcff7b73ad1c9052f0b5999f9aaab7648ba2ef Mon Sep 17 00:00:00 2001 From: David L Stevens Date: Mon, 8 Sep 2014 16:23:01 -0400 Subject: sunvnet - add missing rmb() for sunvnet driver The sunvnet driver does not have an rmb() in the ring consumer corresponding to the wmb() in the producer. According to Documentation/memory-barriers.txt: "When dealing with CPU-CPU interactions, certain types of memory barrier should always be paired. A lack of appropriate pairing is almost certainly an error." In cases where an rmb() is not a no-op and a consumer is removing data from the ring while a producer is adding new entries, a load reorder would allow CPU1 CPU2 ---- ---- LOAD desc.size [e.g] STORE desc.size set desc.hdr.state = VIO_DESC_READY LOAD desc.hdr.state [because VIO_DESC_READY, use old desc.size, already loaded out of order] [CPU2 has reordered apparently unrelated LOADs] To ensure other desc fields are not loaded before checking VIO_DESC_READY, we need an rmb() between the check and desc data accesses. I've also moved the viodbg() call to after the rmb() so that it, too, has current descriptor data even with reordering, which has the side effect that it won't print anything for descriptors that are not VIO_DESC_READY as before. That's a) probably a good thing, since the fields are not necessarily set and, b) better than adding another rmb() just for viodbg(). This would not be possible if strict-ordering is enforced, but then the memory barriers should be no-ops in that case. Signed-off-by: David L Stevens Signed-off-by: David S. Miller --- drivers/net/ethernet/sun/sunvnet.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/sun/sunvnet.c b/drivers/net/ethernet/sun/sunvnet.c index 23c89ab5a6ad..f67539650c38 100644 --- a/drivers/net/ethernet/sun/sunvnet.c +++ b/drivers/net/ethernet/sun/sunvnet.c @@ -350,14 +350,17 @@ static int vnet_walk_rx_one(struct vnet_port *port, if (IS_ERR(desc)) return PTR_ERR(desc); + if (desc->hdr.state != VIO_DESC_READY) + return 1; + + rmb(); + viodbg(DATA, "vio_walk_rx_one desc[%02x:%02x:%08x:%08x:%llx:%llx]\n", desc->hdr.state, desc->hdr.ack, desc->size, desc->ncookies, desc->cookies[0].cookie_addr, desc->cookies[0].cookie_size); - if (desc->hdr.state != VIO_DESC_READY) - return 1; err = vnet_rx_one(port, desc->size, desc->cookies, desc->ncookies); if (err == -ECONNRESET) return err; -- cgit v1.2.1 From 208f7ca4d4a6886256763c9c073775c5fdaf47eb Mon Sep 17 00:00:00 2001 From: Aaro Koskinen Date: Mon, 8 Sep 2014 18:01:53 +0300 Subject: drivers: net: ethernet: octeon_mgmt: fix a compiler warning Fix the following compiler warning: drivers/net/ethernet/octeon/octeon_mgmt.c: In function 'octeon_mgmt_clean_tx_buffers': drivers/net/ethernet/octeon/octeon_mgmt.c:295:4: warning: ISO C90 forbids mixed declarations and code [-Wdeclaration-after-statement] u64 ns = cvmx_read_csr(CVMX_MIXX_TSTAMP(p->port)); ^ Signed-off-by: Aaro Koskinen Acked-by: David Daney Signed-off-by: David S. Miller --- drivers/net/ethernet/octeon/octeon_mgmt.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/octeon/octeon_mgmt.c b/drivers/net/ethernet/octeon/octeon_mgmt.c index 979c6980639f..a42293092ea4 100644 --- a/drivers/net/ethernet/octeon/octeon_mgmt.c +++ b/drivers/net/ethernet/octeon/octeon_mgmt.c @@ -290,9 +290,11 @@ static void octeon_mgmt_clean_tx_buffers(struct octeon_mgmt *p) /* Read the hardware TX timestamp if one was recorded */ if (unlikely(re.s.tstamp)) { struct skb_shared_hwtstamps ts; + u64 ns; + memset(&ts, 0, sizeof(ts)); /* Read the timestamp */ - u64 ns = cvmx_read_csr(CVMX_MIXX_TSTAMP(p->port)); + ns = cvmx_read_csr(CVMX_MIXX_TSTAMP(p->port)); /* Remove the timestamp from the FIFO */ cvmx_write_csr(CVMX_MIXX_TSCTL(p->port), 0); /* Tell the kernel about the timestamp */ -- cgit v1.2.1 From 278d436a476f69fc95d5c82bf61b6c2d02f4d44e Mon Sep 17 00:00:00 2001 From: Ivan Vecera Date: Mon, 8 Sep 2014 18:46:53 +0200 Subject: net/mlx4_en: do not ignore autoneg in mlx4_en_set_pauseparam() The driver does not support pause autonegotiation so it should return -EINVAL when the function is called with non-zero autoneg. Cc: Amir Vadai Signed-off-by: Ivan Vecera Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/en_ethtool.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c b/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c index e22f24f784fc..35ff2925110a 100644 --- a/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c +++ b/drivers/net/ethernet/mellanox/mlx4/en_ethtool.c @@ -487,6 +487,9 @@ static int mlx4_en_set_pauseparam(struct net_device *dev, struct mlx4_en_dev *mdev = priv->mdev; int err; + if (pause->autoneg) + return -EINVAL; + priv->prof->tx_pause = pause->tx_pause != 0; priv->prof->rx_pause = pause->rx_pause != 0; err = mlx4_SET_PORT_general(mdev->dev, priv->port, -- cgit v1.2.1 From fe24ba082b8483c81f546d24e40a55624295b85d Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Mon, 8 Sep 2014 11:37:51 -0700 Subject: net: systemport: check harder for out of memory conditions There is a potential case where we might be failing to refill a control block, leaving it with both a NULL skb pointer *and* a NULL dma_unmap_addr. The way we process incoming packets, by first calling dma_unmap_single(), and then only checking for a potential NULL skb can lead to situations where do pass a NULL dma_unmap_addr() to dma_unmap_single(), resulting in an oops. Fix this my moving the NULL skb check earlier, since no backing skb also means no corresponding DMA mapping for this packet. Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/bcmsysport.c | 31 ++++++++++++++++++------------ 1 file changed, 19 insertions(+), 12 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/broadcom/bcmsysport.c b/drivers/net/ethernet/broadcom/bcmsysport.c index 6f4e18644bd4..d9b9170ed2fc 100644 --- a/drivers/net/ethernet/broadcom/bcmsysport.c +++ b/drivers/net/ethernet/broadcom/bcmsysport.c @@ -534,6 +534,25 @@ static unsigned int bcm_sysport_desc_rx(struct bcm_sysport_priv *priv, while ((processed < to_process) && (processed < budget)) { cb = &priv->rx_cbs[priv->rx_read_ptr]; skb = cb->skb; + + processed++; + priv->rx_read_ptr++; + + if (priv->rx_read_ptr == priv->num_rx_bds) + priv->rx_read_ptr = 0; + + /* We do not have a backing SKB, so we do not a corresponding + * DMA mapping for this incoming packet since + * bcm_sysport_rx_refill always either has both skb and mapping + * or none. + */ + if (unlikely(!skb)) { + netif_err(priv, rx_err, ndev, "out of memory!\n"); + ndev->stats.rx_dropped++; + ndev->stats.rx_errors++; + goto refill; + } + dma_unmap_single(kdev, dma_unmap_addr(cb, dma_addr), RX_BUF_LENGTH, DMA_FROM_DEVICE); @@ -543,23 +562,11 @@ static unsigned int bcm_sysport_desc_rx(struct bcm_sysport_priv *priv, status = (rsb->rx_status_len >> DESC_STATUS_SHIFT) & DESC_STATUS_MASK; - processed++; - priv->rx_read_ptr++; - if (priv->rx_read_ptr == priv->num_rx_bds) - priv->rx_read_ptr = 0; - netif_dbg(priv, rx_status, ndev, "p=%d, c=%d, rd_ptr=%d, len=%d, flag=0x%04x\n", p_index, priv->rx_c_index, priv->rx_read_ptr, len, status); - if (unlikely(!skb)) { - netif_err(priv, rx_err, ndev, "out of memory!\n"); - ndev->stats.rx_dropped++; - ndev->stats.rx_errors++; - goto refill; - } - if (unlikely(!(status & DESC_EOP) || !(status & DESC_SOP))) { netif_err(priv, rx_status, ndev, "fragmented packet!\n"); ndev->stats.rx_dropped++; -- cgit v1.2.1 From b629be5c8399d7c423b92135eb43a86c924d1cbc Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Mon, 8 Sep 2014 11:37:52 -0700 Subject: net: bcmgenet: check harder for out of memory conditions There is a potential case where we might be failing to refill a control block, leaving it with both a NULL skb pointer *and* a NULL dma_unmap_addr. The way we process incoming packets, by first calling dma_unmap_single(), and then only checking for a potential NULL skb can lead to situations where do pass a NULL dma_unmap_addr() to dma_unmap_single(), resulting in an oops. Fix this my moving the NULL skb check earlier, since no backing skb also means no corresponding DMA mapping for this packet. Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/genet/bcmgenet.c | 33 +++++++++++++++----------- 1 file changed, 19 insertions(+), 14 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c index 3f9d4de8173c..cdef86a03862 100644 --- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c +++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c @@ -1274,12 +1274,29 @@ static unsigned int bcmgenet_desc_rx(struct bcmgenet_priv *priv, while ((rxpktprocessed < rxpkttoprocess) && (rxpktprocessed < budget)) { + cb = &priv->rx_cbs[priv->rx_read_ptr]; + skb = cb->skb; + + rxpktprocessed++; + + priv->rx_read_ptr++; + priv->rx_read_ptr &= (priv->num_rx_bds - 1); + + /* We do not have a backing SKB, so we do not have a + * corresponding DMA mapping for this incoming packet since + * bcmgenet_rx_refill always either has both skb and mapping or + * none. + */ + if (unlikely(!skb)) { + dev->stats.rx_dropped++; + dev->stats.rx_errors++; + goto refill; + } + /* Unmap the packet contents such that we can use the * RSV from the 64 bytes descriptor when enabled and save * a 32-bits register read */ - cb = &priv->rx_cbs[priv->rx_read_ptr]; - skb = cb->skb; dma_unmap_single(&dev->dev, dma_unmap_addr(cb, dma_addr), priv->rx_buf_len, DMA_FROM_DEVICE); @@ -1307,18 +1324,6 @@ static unsigned int bcmgenet_desc_rx(struct bcmgenet_priv *priv, __func__, p_index, priv->rx_c_index, priv->rx_read_ptr, dma_length_status); - rxpktprocessed++; - - priv->rx_read_ptr++; - priv->rx_read_ptr &= (priv->num_rx_bds - 1); - - /* out of memory, just drop packets at the hardware level */ - if (unlikely(!skb)) { - dev->stats.rx_dropped++; - dev->stats.rx_errors++; - goto refill; - } - if (unlikely(!(dma_flag & DMA_EOP) || !(dma_flag & DMA_SOP))) { netif_err(priv, rx_status, dev, "dropping fragmented packet!\n"); -- cgit v1.2.1 From a0e2c822bf0a1095dc250b5875e39ac0662a5df6 Mon Sep 17 00:00:00 2001 From: Mugunthan V N Date: Wed, 10 Sep 2014 16:38:09 +0530 Subject: drivers: net: cpsw: dual_emac: fix reducing of rx descriptor during ifdown In Dual EMAC, when both interface are up and while doing ifdown with heavy traffic then skbs already processed by DMA from that slave emac has to be requeued as still the other interface is up and running. Signed-off-by: Mugunthan V N Signed-off-by: David S. Miller --- drivers/net/ethernet/ti/cpsw.c | 23 +++++++++++++++++++++++ 1 file changed, 23 insertions(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c index 999fb72688d2..411232f07c3f 100644 --- a/drivers/net/ethernet/ti/cpsw.c +++ b/drivers/net/ethernet/ti/cpsw.c @@ -699,6 +699,28 @@ static void cpsw_rx_handler(void *token, int len, int status) cpsw_dual_emac_src_port_detect(status, priv, ndev, skb); if (unlikely(status < 0) || unlikely(!netif_running(ndev))) { + bool ndev_status = false; + struct cpsw_slave *slave = priv->slaves; + int n; + + if (priv->data.dual_emac) { + /* In dual emac mode check for all interfaces */ + for (n = priv->data.slaves; n; n--, slave++) + if (netif_running(slave->ndev)) + ndev_status = true; + } + + if (ndev_status && (status >= 0)) { + /* The packet received is for the interface which + * is already down and the other interface is up + * and running, intead of freeing which results + * in reducing of the number of rx descriptor in + * DMA engine, requeue skb back to cpdma. + */ + new_skb = skb; + goto requeue; + } + /* the interface is going down, skbs are purged */ dev_kfree_skb_any(skb); return; @@ -717,6 +739,7 @@ static void cpsw_rx_handler(void *token, int len, int status) new_skb = skb; } +requeue: ret = cpdma_chan_submit(priv->rxch, new_skb, new_skb->data, skb_tailroom(new_skb), 0); if (WARN_ON(ret < 0)) -- cgit v1.2.1 From a91c772fa0275163508e1078ff6d474d423244fb Mon Sep 17 00:00:00 2001 From: Matan Barak Date: Wed, 10 Sep 2014 16:41:53 +0300 Subject: net/mlx4: Correctly configure single ported VFs from the host Single port VFs are seen PCI wise on both ports of the PF (we don't have single port PFs with ConnectX). With this in mind, it's possible for virtualization tools to try and configure a single ported VF through the "wrong" PF port. To handle that, we use the PF driver mapping of single port VFs to NIC ports and adjust the port value before calling into the low level code that does the actual VF configuration Fixes: 449fc48 ('net/mlx4: Adapt code for N-Port VF') Signed-off-by: Matan Barak Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/cmd.c | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/mellanox/mlx4/cmd.c b/drivers/net/ethernet/mellanox/mlx4/cmd.c index 65a4a0f88ea0..02a2e90d581a 100644 --- a/drivers/net/ethernet/mellanox/mlx4/cmd.c +++ b/drivers/net/ethernet/mellanox/mlx4/cmd.c @@ -2389,6 +2389,22 @@ struct mlx4_slaves_pport mlx4_phys_to_slaves_pport_actv( } EXPORT_SYMBOL_GPL(mlx4_phys_to_slaves_pport_actv); +static int mlx4_slaves_closest_port(struct mlx4_dev *dev, int slave, int port) +{ + struct mlx4_active_ports actv_ports = mlx4_get_active_ports(dev, slave); + int min_port = find_first_bit(actv_ports.ports, dev->caps.num_ports) + + 1; + int max_port = min_port + + bitmap_weight(actv_ports.ports, dev->caps.num_ports); + + if (port < min_port) + port = min_port; + else if (port >= max_port) + port = max_port - 1; + + return port; +} + int mlx4_set_vf_mac(struct mlx4_dev *dev, int port, int vf, u64 mac) { struct mlx4_priv *priv = mlx4_priv(dev); @@ -2402,6 +2418,7 @@ int mlx4_set_vf_mac(struct mlx4_dev *dev, int port, int vf, u64 mac) if (slave < 0) return -EINVAL; + port = mlx4_slaves_closest_port(dev, slave, port); s_info = &priv->mfunc.master.vf_admin[slave].vport[port]; s_info->mac = mac; mlx4_info(dev, "default mac on vf %d port %d to %llX will take afect only after vf restart\n", @@ -2428,6 +2445,7 @@ int mlx4_set_vf_vlan(struct mlx4_dev *dev, int port, int vf, u16 vlan, u8 qos) if (slave < 0) return -EINVAL; + port = mlx4_slaves_closest_port(dev, slave, port); vf_admin = &priv->mfunc.master.vf_admin[slave].vport[port]; if ((0 == vlan) && (0 == qos)) @@ -2455,6 +2473,7 @@ bool mlx4_get_slave_default_vlan(struct mlx4_dev *dev, int port, int slave, struct mlx4_priv *priv; priv = mlx4_priv(dev); + port = mlx4_slaves_closest_port(dev, slave, port); vp_oper = &priv->mfunc.master.vf_oper[slave].vport[port]; if (MLX4_VGT != vp_oper->state.default_vlan) { @@ -2482,6 +2501,7 @@ int mlx4_set_vf_spoofchk(struct mlx4_dev *dev, int port, int vf, bool setting) if (slave < 0) return -EINVAL; + port = mlx4_slaves_closest_port(dev, slave, port); s_info = &priv->mfunc.master.vf_admin[slave].vport[port]; s_info->spoofchk = setting; @@ -2535,6 +2555,7 @@ int mlx4_set_vf_link_state(struct mlx4_dev *dev, int port, int vf, int link_stat if (slave < 0) return -EINVAL; + port = mlx4_slaves_closest_port(dev, slave, port); switch (link_state) { case IFLA_VF_LINK_STATE_AUTO: /* get current link state */ -- cgit v1.2.1 From 311be98a3cca6469adf369714d689f9bbf286190 Mon Sep 17 00:00:00 2001 From: Matan Barak Date: Wed, 10 Sep 2014 16:41:54 +0300 Subject: net/mlx4: Use the correct VSD mask in UPDATE_QP When doing VGT->VST->VGT state changes, we used an incorrect mask for the vlan-stripping-disable (VSD) flag, hence the vlan related policy for user-space Raw Ethernet QPs open by VFs wasn't really applied. Fix that, by using the correct mask. Fixes: f0f829b ('net/mlx4_core: Add immediate activate for VGT->VST->VGT') Signed-off-by: Matan Barak Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/resource_tracker.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c b/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c index 1089367fed22..f87a4a38575f 100644 --- a/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c +++ b/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c @@ -4818,7 +4818,7 @@ void mlx4_vf_immed_vlan_work_handler(struct work_struct *_work) MLX4_VLAN_CTRL_ETH_RX_BLOCK_UNTAGGED; upd_context = mailbox->buf; - upd_context->qp_mask = cpu_to_be64(MLX4_UPD_QP_MASK_VSD); + upd_context->qp_mask = cpu_to_be64(1ULL << MLX4_UPD_QP_MASK_VSD); spin_lock_irq(mlx4_tlock(dev)); list_for_each_entry_safe(qp, tmp, qp_list, com.list) { -- cgit v1.2.1 From b7834758e6f33da401f584035f1b6b62d0672aab Mon Sep 17 00:00:00 2001 From: Matan Barak Date: Wed, 10 Sep 2014 16:41:55 +0300 Subject: net/mlx4: Avoid dealing with MAC index in UPDATE_QP wrapper if not needed The current wrapper implementation of the UPDATE_QP command tries to get the MAC index, even if MAC wasn't set by the VF. Fix it up to only handle the MAC field if it's valid. Fixes: ce8d9e0 ('net/mlx4_core: Add UPDATE_QP SRIOV wrapper support') Signed-off-by: Matan Barak Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/resource_tracker.c | 18 +++++++++++------- 1 file changed, 11 insertions(+), 7 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c b/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c index f87a4a38575f..2fe61b6a8e37 100644 --- a/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c +++ b/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c @@ -3998,13 +3998,17 @@ int mlx4_UPDATE_QP_wrapper(struct mlx4_dev *dev, int slave, } port = (rqp->sched_queue >> 6 & 1) + 1; - smac_index = cmd->qp_context.pri_path.grh_mylmc; - err = mac_find_smac_ix_in_slave(dev, slave, port, - smac_index, &mac); - if (err) { - mlx4_err(dev, "Failed to update qpn 0x%x, MAC is invalid. smac_ix: %d\n", - qpn, smac_index); - goto err_mac; + + if (pri_addr_path_mask & (1ULL << MLX4_UPD_QP_PATH_MASK_MAC_INDEX)) { + smac_index = cmd->qp_context.pri_path.grh_mylmc; + err = mac_find_smac_ix_in_slave(dev, slave, port, + smac_index, &mac); + + if (err) { + mlx4_err(dev, "Failed to update qpn 0x%x, MAC is invalid. smac_ix: %d\n", + qpn, smac_index); + goto err_mac; + } } err = mlx4_cmd(dev, inbox->dma, -- cgit v1.2.1 From 09e05c3f78e9e82bda5958eb95bbf719f7a0ed6b Mon Sep 17 00:00:00 2001 From: Matan Barak Date: Wed, 10 Sep 2014 16:41:56 +0300 Subject: net/mlx4: Set vlan stripping policy by the right command Changing the vlan stripping policy of the QP isn't supported by older firmware versions for the INIT2RTR command. Nevertheless, we've used it. Fix that by doing this policy change using INIT2RTR only if the firmware supports it, otherwise, we call UPDATE_QP command to do the task. Fixes: 7677fc9 ('net/mlx4: Strengthen VLAN tags/priorities enforcement in VST mode') Signed-off-by: Matan Barak Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/qp.c | 12 ++++++++++-- drivers/net/ethernet/mellanox/mlx4/resource_tracker.c | 18 ++++++++++++++++-- 2 files changed, 26 insertions(+), 4 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/mellanox/mlx4/qp.c b/drivers/net/ethernet/mellanox/mlx4/qp.c index 0dc31d85fc3b..2301365c79c7 100644 --- a/drivers/net/ethernet/mellanox/mlx4/qp.c +++ b/drivers/net/ethernet/mellanox/mlx4/qp.c @@ -390,13 +390,14 @@ err_icm: EXPORT_SYMBOL_GPL(mlx4_qp_alloc); #define MLX4_UPDATE_QP_SUPPORTED_ATTRS MLX4_UPDATE_QP_SMAC -int mlx4_update_qp(struct mlx4_dev *dev, struct mlx4_qp *qp, +int mlx4_update_qp(struct mlx4_dev *dev, u32 qpn, enum mlx4_update_qp_attr attr, struct mlx4_update_qp_params *params) { struct mlx4_cmd_mailbox *mailbox; struct mlx4_update_qp_context *cmd; u64 pri_addr_path_mask = 0; + u64 qp_mask = 0; int err = 0; mailbox = mlx4_alloc_cmd_mailbox(dev); @@ -413,9 +414,16 @@ int mlx4_update_qp(struct mlx4_dev *dev, struct mlx4_qp *qp, cmd->qp_context.pri_path.grh_mylmc = params->smac_index; } + if (attr & MLX4_UPDATE_QP_VSD) { + qp_mask |= 1ULL << MLX4_UPD_QP_MASK_VSD; + if (params->flags & MLX4_UPDATE_QP_PARAMS_FLAGS_VSD_ENABLE) + cmd->qp_context.param3 |= cpu_to_be32(MLX4_STRIP_VLAN); + } + cmd->primary_addr_path_mask = cpu_to_be64(pri_addr_path_mask); + cmd->qp_mask = cpu_to_be64(qp_mask); - err = mlx4_cmd(dev, mailbox->dma, qp->qpn & 0xffffff, 0, + err = mlx4_cmd(dev, mailbox->dma, qpn & 0xffffff, 0, MLX4_CMD_UPDATE_QP, MLX4_CMD_TIME_CLASS_A, MLX4_CMD_NATIVE); diff --git a/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c b/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c index 2fe61b6a8e37..5d2498dcf536 100644 --- a/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c +++ b/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c @@ -702,11 +702,13 @@ static int update_vport_qp_param(struct mlx4_dev *dev, struct mlx4_qp_context *qpc = inbox->buf + 8; struct mlx4_vport_oper_state *vp_oper; struct mlx4_priv *priv; + u32 qp_type; int port; port = (qpc->pri_path.sched_queue & 0x40) ? 2 : 1; priv = mlx4_priv(dev); vp_oper = &priv->mfunc.master.vf_oper[slave].vport[port]; + qp_type = (be32_to_cpu(qpc->flags) >> 16) & 0xff; if (MLX4_VGT != vp_oper->state.default_vlan) { /* the reserved QPs (special, proxy, tunnel) @@ -715,8 +717,20 @@ static int update_vport_qp_param(struct mlx4_dev *dev, if (mlx4_is_qp_reserved(dev, qpn)) return 0; - /* force strip vlan by clear vsd */ - qpc->param3 &= ~cpu_to_be32(MLX4_STRIP_VLAN); + /* force strip vlan by clear vsd, MLX QP refers to Raw Ethernet */ + if (qp_type == MLX4_QP_ST_UD || + (qp_type == MLX4_QP_ST_MLX && mlx4_is_eth(dev, port))) { + if (dev->caps.bmme_flags & MLX4_BMME_FLAG_VSD_INIT2RTR) { + *(__be32 *)inbox->buf = + cpu_to_be32(be32_to_cpu(*(__be32 *)inbox->buf) | + MLX4_QP_OPTPAR_VLAN_STRIPPING); + qpc->param3 &= ~cpu_to_be32(MLX4_STRIP_VLAN); + } else { + struct mlx4_update_qp_params params = {.flags = 0}; + + mlx4_update_qp(dev, qpn, MLX4_UPDATE_QP_VSD, ¶ms); + } + } if (vp_oper->state.link_state == IFLA_VF_LINK_STATE_DISABLE && dev->caps.flags2 & MLX4_DEV_CAP_FLAG2_UPDATE_QP) { -- cgit v1.2.1 From 7ce7679d6bbd1715799a9cf17b9b558bc2d962b7 Mon Sep 17 00:00:00 2001 From: Beniamino Galvani Date: Wed, 10 Sep 2014 22:50:02 +0200 Subject: net: arc_emac: enable tx interrupts In the current implementation the cleaning of tx ring is done by the NAPI poll handler, which is scheduled after rx interrupts. Thus, in absence of received packets the reclaim of used tx buffers is never executed, blocking further transmission. This can be easily reproduced starting the transmission of a UDP flow with iperf, which blocks almost immediately because skbs are not returned to the stack and the socket send buffer becomes full. The patch enables tx interrupts so that the tx reclaim is scheduled after completed transmissions. Signed-off-by: Beniamino Galvani Reviewed-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/ethernet/arc/emac_main.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/arc/emac_main.c b/drivers/net/ethernet/arc/emac_main.c index fe5cfeace6e3..f7ab90d9cd7e 100644 --- a/drivers/net/ethernet/arc/emac_main.c +++ b/drivers/net/ethernet/arc/emac_main.c @@ -298,7 +298,7 @@ static int arc_emac_poll(struct napi_struct *napi, int budget) work_done = arc_emac_rx(ndev, budget); if (work_done < budget) { napi_complete(napi); - arc_reg_or(priv, R_ENABLE, RXINT_MASK); + arc_reg_or(priv, R_ENABLE, RXINT_MASK | TXINT_MASK); } return work_done; @@ -327,9 +327,9 @@ static irqreturn_t arc_emac_intr(int irq, void *dev_instance) /* Reset all flags except "MDIO complete" */ arc_reg_set(priv, R_STATUS, status); - if (status & RXINT_MASK) { + if (status & (RXINT_MASK | TXINT_MASK)) { if (likely(napi_schedule_prep(&priv->napi))) { - arc_reg_clr(priv, R_ENABLE, RXINT_MASK); + arc_reg_clr(priv, R_ENABLE, RXINT_MASK | TXINT_MASK); __napi_schedule(&priv->napi); } } @@ -440,7 +440,7 @@ static int arc_emac_open(struct net_device *ndev) arc_reg_set(priv, R_TX_RING, (unsigned int)priv->txbd_dma); /* Enable interrupts */ - arc_reg_set(priv, R_ENABLE, RXINT_MASK | ERR_MASK); + arc_reg_set(priv, R_ENABLE, RXINT_MASK | TXINT_MASK | ERR_MASK); /* Set CONTROL */ arc_reg_set(priv, R_CTRL, @@ -511,7 +511,7 @@ static int arc_emac_stop(struct net_device *ndev) netif_stop_queue(ndev); /* Disable interrupts */ - arc_reg_clr(priv, R_ENABLE, RXINT_MASK | ERR_MASK); + arc_reg_clr(priv, R_ENABLE, RXINT_MASK | TXINT_MASK | ERR_MASK); /* Disable EMAC */ arc_reg_clr(priv, R_CTRL, EN_MASK); -- cgit v1.2.1 From 74dd40bca95f9968e368751ea81f3b98471109ce Mon Sep 17 00:00:00 2001 From: Beniamino Galvani Date: Wed, 10 Sep 2014 22:50:03 +0200 Subject: net: arc_emac: prevent reuse of unreclaimed tx descriptors This patch changes the logic in tx path to ensure that tx descriptors are reused for transmission only after they have been reclaimed by arc_emac_tx_clean(). Signed-off-by: Beniamino Galvani Signed-off-by: David S. Miller --- drivers/net/ethernet/arc/emac_main.c | 43 +++++++++++++++++++++++++++--------- 1 file changed, 32 insertions(+), 11 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/arc/emac_main.c b/drivers/net/ethernet/arc/emac_main.c index f7ab90d9cd7e..5919394d9f58 100644 --- a/drivers/net/ethernet/arc/emac_main.c +++ b/drivers/net/ethernet/arc/emac_main.c @@ -29,6 +29,17 @@ #define DRV_NAME "arc_emac" #define DRV_VERSION "1.0" +/** + * arc_emac_tx_avail - Return the number of available slots in the tx ring. + * @priv: Pointer to ARC EMAC private data structure. + * + * returns: the number of slots available for transmission in tx the ring. + */ +static inline int arc_emac_tx_avail(struct arc_emac_priv *priv) +{ + return (priv->txbd_dirty + TX_BD_NUM - priv->txbd_curr - 1) % TX_BD_NUM; +} + /** * arc_emac_adjust_link - Adjust the PHY link duplex. * @ndev: Pointer to the net_device structure. @@ -180,10 +191,15 @@ static void arc_emac_tx_clean(struct net_device *ndev) txbd->info = 0; *txbd_dirty = (*txbd_dirty + 1) % TX_BD_NUM; - - if (netif_queue_stopped(ndev)) - netif_wake_queue(ndev); } + + /* Ensure that txbd_dirty is visible to tx() before checking + * for queue stopped. + */ + smp_mb(); + + if (netif_queue_stopped(ndev) && arc_emac_tx_avail(priv)) + netif_wake_queue(ndev); } /** @@ -574,11 +590,9 @@ static int arc_emac_tx(struct sk_buff *skb, struct net_device *ndev) len = max_t(unsigned int, ETH_ZLEN, skb->len); - /* EMAC still holds this buffer in its possession. - * CPU must not modify this buffer descriptor - */ - if (unlikely((le32_to_cpu(*info) & OWN_MASK) == FOR_EMAC)) { + if (unlikely(!arc_emac_tx_avail(priv))) { netif_stop_queue(ndev); + netdev_err(ndev, "BUG! Tx Ring full when queue awake!\n"); return NETDEV_TX_BUSY; } @@ -607,12 +621,19 @@ static int arc_emac_tx(struct sk_buff *skb, struct net_device *ndev) /* Increment index to point to the next BD */ *txbd_curr = (*txbd_curr + 1) % TX_BD_NUM; - /* Get "info" of the next BD */ - info = &priv->txbd[*txbd_curr].info; + /* Ensure that tx_clean() sees the new txbd_curr before + * checking the queue status. This prevents an unneeded wake + * of the queue in tx_clean(). + */ + smp_mb(); - /* Check if if Tx BD ring is full - next BD is still owned by EMAC */ - if (unlikely((le32_to_cpu(*info) & OWN_MASK) == FOR_EMAC)) + if (!arc_emac_tx_avail(priv)) { netif_stop_queue(ndev); + /* Refresh tx_dirty */ + smp_mb(); + if (arc_emac_tx_avail(priv)) + netif_start_queue(ndev); + } arc_reg_set(priv, R_STATUS, TXPL_MASK); -- cgit v1.2.1 From 0bc9b73be43b21838973e80ddeb5250f0310ebf7 Mon Sep 17 00:00:00 2001 From: Mark Einon Date: Thu, 11 Sep 2014 23:19:49 +0100 Subject: drivers: net: b44: Fix typo in returning multicast stats nstat->multicast refers to received packets, not transmitted as is returned here. Change it so that received packet stats are given. Signed-off-by: Mark Einon Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/b44.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/broadcom/b44.c b/drivers/net/ethernet/broadcom/b44.c index 4a7028d65912..d588136b23b9 100644 --- a/drivers/net/ethernet/broadcom/b44.c +++ b/drivers/net/ethernet/broadcom/b44.c @@ -1697,7 +1697,7 @@ static struct rtnl_link_stats64 *b44_get_stats64(struct net_device *dev, hwstat->tx_underruns + hwstat->tx_excessive_cols + hwstat->tx_late_cols); - nstat->multicast = hwstat->tx_multicast_pkts; + nstat->multicast = hwstat->rx_multicast_pkts; nstat->collisions = hwstat->tx_total_cols; nstat->rx_length_errors = (hwstat->rx_oversize_pkts + -- cgit v1.2.1 From 618073e30c225ddaef086c030a5f0a3c7ef2d323 Mon Sep 17 00:00:00 2001 From: Mugunthan V N Date: Thu, 11 Sep 2014 22:52:38 +0530 Subject: drivers: net: cpsw: dual_emac: in suspend/resume bring down/up all the netdev During suspend and resume in Dual EMAC, second port is not working as in suspend/resume only the first slave netdev is closed and opened. So bring down and up all the interfaces that are up during suspend/resume. Signed-off-by: Mugunthan V N Tested-by: Nishanth Menon Signed-off-by: David S. Miller --- drivers/net/ethernet/ti/cpsw.c | 29 ++++++++++++++++++++++++----- 1 file changed, 24 insertions(+), 5 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c index 411232f07c3f..e2a00287f8eb 100644 --- a/drivers/net/ethernet/ti/cpsw.c +++ b/drivers/net/ethernet/ti/cpsw.c @@ -2334,10 +2334,19 @@ static int cpsw_suspend(struct device *dev) struct net_device *ndev = platform_get_drvdata(pdev); struct cpsw_priv *priv = netdev_priv(ndev); - if (netif_running(ndev)) - cpsw_ndo_stop(ndev); + if (priv->data.dual_emac) { + int i; - for_each_slave(priv, soft_reset_slave); + for (i = 0; i < priv->data.slaves; i++) { + if (netif_running(priv->slaves[i].ndev)) + cpsw_ndo_stop(priv->slaves[i].ndev); + soft_reset_slave(priv->slaves + i); + } + } else { + if (netif_running(ndev)) + cpsw_ndo_stop(ndev); + for_each_slave(priv, soft_reset_slave); + } pm_runtime_put_sync(&pdev->dev); @@ -2351,14 +2360,24 @@ static int cpsw_resume(struct device *dev) { struct platform_device *pdev = to_platform_device(dev); struct net_device *ndev = platform_get_drvdata(pdev); + struct cpsw_priv *priv = netdev_priv(ndev); pm_runtime_get_sync(&pdev->dev); /* Select default pin state */ pinctrl_pm_select_default_state(&pdev->dev); - if (netif_running(ndev)) - cpsw_ndo_open(ndev); + if (priv->data.dual_emac) { + int i; + + for (i = 0; i < priv->data.slaves; i++) { + if (netif_running(priv->slaves[i].ndev)) + cpsw_ndo_open(priv->slaves[i].ndev); + } + } else { + if (netif_running(ndev)) + cpsw_ndo_open(ndev); + } return 0; } -- cgit v1.2.1 From 48c20407f49039d8da155ca00877ec5f057799e6 Mon Sep 17 00:00:00 2001 From: hayeswang Date: Fri, 12 Sep 2014 11:35:11 +0800 Subject: r8169: fix the default setting of rx vlan If the parameter "features" of __rtl8169_set_features() is equal to dev->features, the variable "changed" is alwayes 0, and nothing would be changed. Signed-off-by: Hayes Wang Signed-off-by: David S. Miller --- drivers/net/ethernet/realtek/r8169.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index 91652e7235e4..f3ce284e54f0 100644 --- a/drivers/net/ethernet/realtek/r8169.c +++ b/drivers/net/ethernet/realtek/r8169.c @@ -6707,7 +6707,12 @@ static int rtl_open(struct net_device *dev) rtl8169_init_phy(dev, tp); - __rtl8169_set_features(dev, dev->features); + if (dev->features & NETIF_F_HW_VLAN_CTAG_RX) + tp->cp_cmd |= RxVlan; + else + tp->cp_cmd &= ~RxVlan; + + RTL_W16(CPlusCmd, tp->cp_cmd); rtl_pll_power_up(tp); -- cgit v1.2.1 From 36d8e82541c4be8f529dce9efbcefd504e085ccf Mon Sep 17 00:00:00 2001 From: hayeswang Date: Fri, 12 Sep 2014 11:35:12 +0800 Subject: r8169: fix setting rx vlan The setting should depend on the new features not the current one. Signed-off-by: Hayes Wang Signed-off-by: David S. Miller --- drivers/net/ethernet/realtek/r8169.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index f3ce284e54f0..7a7860a17f69 100644 --- a/drivers/net/ethernet/realtek/r8169.c +++ b/drivers/net/ethernet/realtek/r8169.c @@ -1796,7 +1796,7 @@ static void __rtl8169_set_features(struct net_device *dev, else tp->cp_cmd &= ~RxChkSum; - if (dev->features & NETIF_F_HW_VLAN_CTAG_RX) + if (features & NETIF_F_HW_VLAN_CTAG_RX) tp->cp_cmd |= RxVlan; else tp->cp_cmd &= ~RxVlan; -- cgit v1.2.1 From d6ce2628f32271c037a8c12e1994c9fba3a4af49 Mon Sep 17 00:00:00 2001 From: Hariprasad Shenai Date: Tue, 16 Sep 2014 02:58:46 +0530 Subject: cxgb4: Don't allocate adapter structure for all PF's commit 35b1de557970 ("rdma/cxgb4: Fixes cxgb4 probe failure in VM when PF is exposed through PCI Passthrough") moved the code to check for SR-IOV PF[0..3] much further down in init_one() past the point where we allocate a (struct adapter) for PF[0..3]. As a result, we left four of these on ever module remove. Fix: Allocate adapter structure only for PF4 Signed-off-by: Hariprasad Shenai Signed-off-by: David S. Miller --- drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c | 49 ++++++++++++++----------- 1 file changed, 27 insertions(+), 22 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c index 8c34811a1128..e5be511a3c38 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c +++ b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c @@ -6478,6 +6478,7 @@ static int init_one(struct pci_dev *pdev, const struct pci_device_id *ent) struct port_info *pi; bool highdma = false; struct adapter *adapter = NULL; + void __iomem *regs; printk_once(KERN_INFO "%s - version %s\n", DRV_DESC, DRV_VERSION); @@ -6494,19 +6495,35 @@ static int init_one(struct pci_dev *pdev, const struct pci_device_id *ent) goto out_release_regions; } + regs = pci_ioremap_bar(pdev, 0); + if (!regs) { + dev_err(&pdev->dev, "cannot map device registers\n"); + err = -ENOMEM; + goto out_disable_device; + } + + /* We control everything through one PF */ + func = SOURCEPF_GET(readl(regs + PL_WHOAMI)); + if (func != ent->driver_data) { + iounmap(regs); + pci_disable_device(pdev); + pci_save_state(pdev); /* to restore SR-IOV later */ + goto sriov; + } + if (!pci_set_dma_mask(pdev, DMA_BIT_MASK(64))) { highdma = true; err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(64)); if (err) { dev_err(&pdev->dev, "unable to obtain 64-bit DMA for " "coherent allocations\n"); - goto out_disable_device; + goto out_unmap_bar0; } } else { err = pci_set_dma_mask(pdev, DMA_BIT_MASK(32)); if (err) { dev_err(&pdev->dev, "no usable DMA configuration\n"); - goto out_disable_device; + goto out_unmap_bar0; } } @@ -6518,7 +6535,7 @@ static int init_one(struct pci_dev *pdev, const struct pci_device_id *ent) adapter = kzalloc(sizeof(*adapter), GFP_KERNEL); if (!adapter) { err = -ENOMEM; - goto out_disable_device; + goto out_unmap_bar0; } adapter->workq = create_singlethread_workqueue("cxgb4"); @@ -6530,20 +6547,7 @@ static int init_one(struct pci_dev *pdev, const struct pci_device_id *ent) /* PCI device has been enabled */ adapter->flags |= DEV_ENABLED; - adapter->regs = pci_ioremap_bar(pdev, 0); - if (!adapter->regs) { - dev_err(&pdev->dev, "cannot map device registers\n"); - err = -ENOMEM; - goto out_free_adapter; - } - - /* We control everything through one PF */ - func = SOURCEPF_GET(readl(adapter->regs + PL_WHOAMI)); - if (func != ent->driver_data) { - pci_save_state(pdev); /* to restore SR-IOV later */ - goto sriov; - } - + adapter->regs = regs; adapter->pdev = pdev; adapter->pdev_dev = &pdev->dev; adapter->mbox = func; @@ -6560,7 +6564,8 @@ static int init_one(struct pci_dev *pdev, const struct pci_device_id *ent) err = t4_prep_adapter(adapter); if (err) - goto out_unmap_bar0; + goto out_free_adapter; + if (!is_t4(adapter->params.chip)) { s_qpp = QUEUESPERPAGEPF1 * adapter->fn; @@ -6577,14 +6582,14 @@ static int init_one(struct pci_dev *pdev, const struct pci_device_id *ent) dev_err(&pdev->dev, "Incorrect number of egress queues per page\n"); err = -EINVAL; - goto out_unmap_bar0; + goto out_free_adapter; } adapter->bar2 = ioremap_wc(pci_resource_start(pdev, 2), pci_resource_len(pdev, 2)); if (!adapter->bar2) { dev_err(&pdev->dev, "cannot map device bar2 region\n"); err = -ENOMEM; - goto out_unmap_bar0; + goto out_free_adapter; } } @@ -6722,13 +6727,13 @@ sriov: out_unmap_bar: if (!is_t4(adapter->params.chip)) iounmap(adapter->bar2); - out_unmap_bar0: - iounmap(adapter->regs); out_free_adapter: if (adapter->workq) destroy_workqueue(adapter->workq); kfree(adapter); + out_unmap_bar0: + iounmap(regs); out_disable_device: pci_disable_pcie_error_reporting(pdev); pci_disable_device(pdev); -- cgit v1.2.1 From 929a031dfd62aae34bf8e728f712e6751e416d1f Mon Sep 17 00:00:00 2001 From: hayeswang Date: Tue, 16 Sep 2014 11:40:47 +0800 Subject: r8169: adjust __rtl8169_set_features Remove the "changed" test in __rtl8169_set_features(). Instead, do simple test in rtl8169_set_features(). Set the RxChkSum and RxVlan through __rtl8169_set_features() in rtl_open(). Signed-off-by: Francois Romieu Signed-off-by: Hayes Wang Signed-off-by: David S. Miller --- drivers/net/ethernet/realtek/r8169.c | 74 +++++++++++++++++------------------- 1 file changed, 34 insertions(+), 40 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index 7a7860a17f69..ef2cee5de62b 100644 --- a/drivers/net/ethernet/realtek/r8169.c +++ b/drivers/net/ethernet/realtek/r8169.c @@ -1783,33 +1783,31 @@ static void __rtl8169_set_features(struct net_device *dev, netdev_features_t features) { struct rtl8169_private *tp = netdev_priv(dev); - netdev_features_t changed = features ^ dev->features; void __iomem *ioaddr = tp->mmio_addr; + u32 rx_config; - if (!(changed & (NETIF_F_RXALL | NETIF_F_RXCSUM | - NETIF_F_HW_VLAN_CTAG_RX))) - return; + rx_config = RTL_R32(RxConfig); + if (features & NETIF_F_RXALL) + rx_config |= (AcceptErr | AcceptRunt); + else + rx_config &= ~(AcceptErr | AcceptRunt); - if (changed & (NETIF_F_RXCSUM | NETIF_F_HW_VLAN_CTAG_RX)) { - if (features & NETIF_F_RXCSUM) - tp->cp_cmd |= RxChkSum; - else - tp->cp_cmd &= ~RxChkSum; + RTL_W32(RxConfig, rx_config); - if (features & NETIF_F_HW_VLAN_CTAG_RX) - tp->cp_cmd |= RxVlan; - else - tp->cp_cmd &= ~RxVlan; + if (features & NETIF_F_RXCSUM) + tp->cp_cmd |= RxChkSum; + else + tp->cp_cmd &= ~RxChkSum; - RTL_W16(CPlusCmd, tp->cp_cmd); - RTL_R16(CPlusCmd); - } - if (changed & NETIF_F_RXALL) { - int tmp = (RTL_R32(RxConfig) & ~(AcceptErr | AcceptRunt)); - if (features & NETIF_F_RXALL) - tmp |= (AcceptErr | AcceptRunt); - RTL_W32(RxConfig, tmp); - } + if (features & NETIF_F_HW_VLAN_CTAG_RX) + tp->cp_cmd |= RxVlan; + else + tp->cp_cmd &= ~RxVlan; + + tp->cp_cmd |= RTL_R16(CPlusCmd) & ~(RxVlan | RxChkSum); + + RTL_W16(CPlusCmd, tp->cp_cmd); + RTL_R16(CPlusCmd); } static int rtl8169_set_features(struct net_device *dev, @@ -1817,8 +1815,11 @@ static int rtl8169_set_features(struct net_device *dev, { struct rtl8169_private *tp = netdev_priv(dev); + features &= NETIF_F_RXALL | NETIF_F_RXCSUM | NETIF_F_HW_VLAN_CTAG_RX; + rtl_lock_work(tp); - __rtl8169_set_features(dev, features); + if (features ^ dev->features); + __rtl8169_set_features(dev, features); rtl_unlock_work(tp); return 0; @@ -6707,12 +6708,7 @@ static int rtl_open(struct net_device *dev) rtl8169_init_phy(dev, tp); - if (dev->features & NETIF_F_HW_VLAN_CTAG_RX) - tp->cp_cmd |= RxVlan; - else - tp->cp_cmd &= ~RxVlan; - - RTL_W16(CPlusCmd, tp->cp_cmd); + __rtl8169_set_features(dev, dev->features); rtl_pll_power_up(tp); @@ -7123,8 +7119,7 @@ static void rtl_hw_initialize(struct rtl8169_private *tp) } } -static int -rtl_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) +static int rtl_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) { const struct rtl_cfg_info *cfg = rtl_cfg_infos + ent->driver_data; const unsigned int region = cfg->region; @@ -7199,7 +7194,7 @@ rtl_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) goto err_out_mwi_2; } - tp->cp_cmd = RxChkSum; + tp->cp_cmd = 0; if ((sizeof(dma_addr_t) > 4) && !pci_set_dma_mask(pdev, DMA_BIT_MASK(64)) && use_dac) { @@ -7240,13 +7235,6 @@ rtl_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) pci_set_master(pdev); - /* - * Pretend we are using VLANs; This bypasses a nasty bug where - * Interrupts stop flowing on high load on 8110SCd controllers. - */ - if (tp->mac_version == RTL_GIGA_MAC_VER_05) - tp->cp_cmd |= RxVlan; - rtl_init_mdio_ops(tp); rtl_init_pll_power_ops(tp); rtl_init_jumbo_ops(tp); @@ -7307,8 +7295,14 @@ rtl_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) dev->vlan_features = NETIF_F_SG | NETIF_F_IP_CSUM | NETIF_F_TSO | NETIF_F_HIGHDMA; + tp->cp_cmd |= RxChkSum | RxVlan; + + /* + * Pretend we are using VLANs; This bypasses a nasty bug where + * Interrupts stop flowing on high load on 8110SCd controllers. + */ if (tp->mac_version == RTL_GIGA_MAC_VER_05) - /* 8110SCd requires hardware Rx VLAN - disallow toggling */ + /* Disallow toggling */ dev->hw_features &= ~NETIF_F_HW_VLAN_CTAG_RX; if (tp->txd_version == RTL_TD_0) -- cgit v1.2.1 From f650fb456f2079b762c131a11397c0a966e2bfe4 Mon Sep 17 00:00:00 2001 From: Edward Cree Date: Tue, 16 Sep 2014 17:05:21 +0100 Subject: sfc: fix addr_list_lock spinlock use before init Reported by Nikolay Aleksandrov. In efx_init_port() we call efx_mac_reconfigure() to work around a Falcon/A1 limitation, and this calls efx_{arch}_filter_sync_rx_mode(), which takes the addr_list_lock; but this lock is uninitialised, because we haven't called register_netdevice() yet. So, in efx_farch_filter_sync_rx_mode(), check efx_dev_registered() before doing anything else. The EF10 equivalent, efx_ef10_filter_sync_rx_mode(), already has the corresponding check. Signed-off-by: Edward Cree Tested-by: Nikolay Aleksandrov Signed-off-by: David S. Miller --- drivers/net/ethernet/sfc/farch.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/sfc/farch.c b/drivers/net/ethernet/sfc/farch.c index 0537381cd2f6..6859437b59fb 100644 --- a/drivers/net/ethernet/sfc/farch.c +++ b/drivers/net/ethernet/sfc/farch.c @@ -2933,6 +2933,9 @@ void efx_farch_filter_sync_rx_mode(struct efx_nic *efx) u32 crc; int bit; + if (!efx_dev_registered(efx)) + return; + netif_addr_lock_bh(net_dev); efx->unicast_filter = !(net_dev->flags & IFF_PROMISC); -- cgit v1.2.1 From 6f2b6a3005b2c34c39f207a87667564f64f2f91a Mon Sep 17 00:00:00 2001 From: Neil Horman Date: Wed, 17 Sep 2014 09:04:44 -0400 Subject: 3c59x: Add dma error checking and recovery Noted that 3c59x has no checks on transmit for failed DMA mappings, and no ability to unmap fragments when a single map fails in the middle of a transmit. This patch provides error checking to ensure that dma mappings work properly, and unrolls an skb mapping if a fragmented skb transmission has a mapping failure to prevent leaks. Signed-off-by: Neil Horman CC: Linux Kernel list CC: "David S. Miller" CC: Meelis Roos Tested-by: Meelis Roos --- drivers/net/ethernet/3com/3c59x.c | 50 ++++++++++++++++++++++++++++++++------- 1 file changed, 41 insertions(+), 9 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/3com/3c59x.c b/drivers/net/ethernet/3com/3c59x.c index 3fe45c705933..8ab87ff6a9e6 100644 --- a/drivers/net/ethernet/3com/3c59x.c +++ b/drivers/net/ethernet/3com/3c59x.c @@ -2129,6 +2129,7 @@ boomerang_start_xmit(struct sk_buff *skb, struct net_device *dev) int entry = vp->cur_tx % TX_RING_SIZE; struct boom_tx_desc *prev_entry = &vp->tx_ring[(vp->cur_tx-1) % TX_RING_SIZE]; unsigned long flags; + dma_addr_t dma_addr; if (vortex_debug > 6) { pr_debug("boomerang_start_xmit()\n"); @@ -2163,24 +2164,48 @@ boomerang_start_xmit(struct sk_buff *skb, struct net_device *dev) vp->tx_ring[entry].status = cpu_to_le32(skb->len | TxIntrUploaded | AddTCPChksum | AddUDPChksum); if (!skb_shinfo(skb)->nr_frags) { - vp->tx_ring[entry].frag[0].addr = cpu_to_le32(pci_map_single(VORTEX_PCI(vp), skb->data, - skb->len, PCI_DMA_TODEVICE)); + dma_addr = pci_map_single(VORTEX_PCI(vp), skb->data, skb->len, + PCI_DMA_TODEVICE); + if (dma_mapping_error(&VORTEX_PCI(vp)->dev, dma_addr)) + goto out_dma_err; + + vp->tx_ring[entry].frag[0].addr = cpu_to_le32(dma_addr); vp->tx_ring[entry].frag[0].length = cpu_to_le32(skb->len | LAST_FRAG); } else { int i; - vp->tx_ring[entry].frag[0].addr = cpu_to_le32(pci_map_single(VORTEX_PCI(vp), skb->data, - skb_headlen(skb), PCI_DMA_TODEVICE)); + dma_addr = pci_map_single(VORTEX_PCI(vp), skb->data, + skb_headlen(skb), PCI_DMA_TODEVICE); + if (dma_mapping_error(&VORTEX_PCI(vp)->dev, dma_addr)) + goto out_dma_err; + + vp->tx_ring[entry].frag[0].addr = cpu_to_le32(dma_addr); vp->tx_ring[entry].frag[0].length = cpu_to_le32(skb_headlen(skb)); for (i = 0; i < skb_shinfo(skb)->nr_frags; i++) { skb_frag_t *frag = &skb_shinfo(skb)->frags[i]; + dma_addr = skb_frag_dma_map(&VORTEX_PCI(vp)->dev, frag, + frag->page_offset, + frag->size, + DMA_TO_DEVICE); + if (dma_mapping_error(&VORTEX_PCI(vp)->dev, dma_addr)) { + for(i = i-1; i >= 0; i--) + dma_unmap_page(&VORTEX_PCI(vp)->dev, + le32_to_cpu(vp->tx_ring[entry].frag[i+1].addr), + le32_to_cpu(vp->tx_ring[entry].frag[i+1].length), + DMA_TO_DEVICE); + + pci_unmap_single(VORTEX_PCI(vp), + le32_to_cpu(vp->tx_ring[entry].frag[0].addr), + le32_to_cpu(vp->tx_ring[entry].frag[0].length), + PCI_DMA_TODEVICE); + + goto out_dma_err; + } + vp->tx_ring[entry].frag[i+1].addr = - cpu_to_le32(skb_frag_dma_map( - &VORTEX_PCI(vp)->dev, - frag, - frag->page_offset, frag->size, DMA_TO_DEVICE)); + cpu_to_le32(dma_addr); if (i == skb_shinfo(skb)->nr_frags-1) vp->tx_ring[entry].frag[i+1].length = cpu_to_le32(skb_frag_size(frag)|LAST_FRAG); @@ -2189,7 +2214,10 @@ boomerang_start_xmit(struct sk_buff *skb, struct net_device *dev) } } #else - vp->tx_ring[entry].addr = cpu_to_le32(pci_map_single(VORTEX_PCI(vp), skb->data, skb->len, PCI_DMA_TODEVICE)); + dma_addr = cpu_to_le32(pci_map_single(VORTEX_PCI(vp), skb->data, skb->len, PCI_DMA_TODEVICE)); + if (dma_mapping_error(&VORTEX_PCI(vp)->dev, dma_addr)) + goto out_dma_err; + vp->tx_ring[entry].addr = cpu_to_le32(dma_addr); vp->tx_ring[entry].length = cpu_to_le32(skb->len | LAST_FRAG); vp->tx_ring[entry].status = cpu_to_le32(skb->len | TxIntrUploaded); #endif @@ -2217,7 +2245,11 @@ boomerang_start_xmit(struct sk_buff *skb, struct net_device *dev) skb_tx_timestamp(skb); iowrite16(DownUnstall, ioaddr + EL3_CMD); spin_unlock_irqrestore(&vp->lock, flags); +out: return NETDEV_TX_OK; +out_dma_err: + dev_err(&VORTEX_PCI(vp)->dev, "Error mapping dma buffer\n"); + goto out; } /* The interrupt handler does all of the Rx thread work and cleans up -- cgit v1.2.1 From 8400dd029e764e30361a51a7ae35900ae0032b43 Mon Sep 17 00:00:00 2001 From: Neil Horman Date: Wed, 17 Sep 2014 09:04:45 -0400 Subject: 3c59x: Fix bad offset spec in skb_frag_dma_map Recently aded the use of skb_frag_dma_map to 3c59x, but didn't realize it automatically included the frag_offset internally, as well as provided an option to specify an extra offset in the parameter list. We need to specify an offset of 0 in the parameter list to avoid skb corruption that results in lost connections. Signed-off-by: Neil Horman CC: Linux Kernel list CC: "David S. Miller" CC: Meelis Roos Tested-by: Meelis Roos --- drivers/net/ethernet/3com/3c59x.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/3com/3c59x.c b/drivers/net/ethernet/3com/3c59x.c index 8ab87ff6a9e6..8ca49f04acec 100644 --- a/drivers/net/ethernet/3com/3c59x.c +++ b/drivers/net/ethernet/3com/3c59x.c @@ -2186,7 +2186,7 @@ boomerang_start_xmit(struct sk_buff *skb, struct net_device *dev) skb_frag_t *frag = &skb_shinfo(skb)->frags[i]; dma_addr = skb_frag_dma_map(&VORTEX_PCI(vp)->dev, frag, - frag->page_offset, + 0, frag->size, DMA_TO_DEVICE); if (dma_mapping_error(&VORTEX_PCI(vp)->dev, dma_addr)) { -- cgit v1.2.1 From 4ff0acca7344c93fd9ed778b4c3ce16d95c594e4 Mon Sep 17 00:00:00 2001 From: Matan Barak Date: Thu, 11 Sep 2014 13:18:37 +0300 Subject: mlx4: Correct error flows in rereg_mr This patch addresses feedback from Sagi Grimberg on the rereg_mr implementation of mlx4. The following are fixed: 1. Set the correct pd_flags 2. Make sure we change the iova and size MR fields only after successful write and allocation of the MTTs. 3. Make the error checking more robust Fixes: e630664c8383 ("mlx4_core: Add helper functions to support MR re-registration") Signed-off-by: Matan Barak Signed-off-by: Or Gerlitz Signed-off-by: Roland Dreier --- drivers/net/ethernet/mellanox/mlx4/mr.c | 33 ++++++++++++++++++++++----------- 1 file changed, 22 insertions(+), 11 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/mellanox/mlx4/mr.c b/drivers/net/ethernet/mellanox/mlx4/mr.c index 7d717eccb7b0..193a6adb5d04 100644 --- a/drivers/net/ethernet/mellanox/mlx4/mr.c +++ b/drivers/net/ethernet/mellanox/mlx4/mr.c @@ -298,6 +298,7 @@ static int mlx4_HW2SW_MPT(struct mlx4_dev *dev, struct mlx4_cmd_mailbox *mailbox MLX4_CMD_TIME_CLASS_B, MLX4_CMD_WRAPPED); } +/* Must protect against concurrent access */ int mlx4_mr_hw_get_mpt(struct mlx4_dev *dev, struct mlx4_mr *mmr, struct mlx4_mpt_entry ***mpt_entry) { @@ -305,13 +306,10 @@ int mlx4_mr_hw_get_mpt(struct mlx4_dev *dev, struct mlx4_mr *mmr, int key = key_to_hw_index(mmr->key) & (dev->caps.num_mpts - 1); struct mlx4_cmd_mailbox *mailbox = NULL; - /* Make sure that at this point we have single-threaded access only */ - if (mmr->enabled != MLX4_MPT_EN_HW) return -EINVAL; err = mlx4_HW2SW_MPT(dev, NULL, key); - if (err) { mlx4_warn(dev, "HW2SW_MPT failed (%d).", err); mlx4_warn(dev, "Most likely the MR has MWs bound to it.\n"); @@ -333,7 +331,6 @@ int mlx4_mr_hw_get_mpt(struct mlx4_dev *dev, struct mlx4_mr *mmr, 0, MLX4_CMD_QUERY_MPT, MLX4_CMD_TIME_CLASS_B, MLX4_CMD_WRAPPED); - if (err) goto free_mailbox; @@ -378,9 +375,10 @@ int mlx4_mr_hw_write_mpt(struct mlx4_dev *dev, struct mlx4_mr *mmr, err = mlx4_SW2HW_MPT(dev, mailbox, key); } - mmr->pd = be32_to_cpu((*mpt_entry)->pd_flags) & MLX4_MPT_PD_MASK; - if (!err) + if (!err) { + mmr->pd = be32_to_cpu((*mpt_entry)->pd_flags) & MLX4_MPT_PD_MASK; mmr->enabled = MLX4_MPT_EN_HW; + } return err; } EXPORT_SYMBOL_GPL(mlx4_mr_hw_write_mpt); @@ -400,11 +398,12 @@ EXPORT_SYMBOL_GPL(mlx4_mr_hw_put_mpt); int mlx4_mr_hw_change_pd(struct mlx4_dev *dev, struct mlx4_mpt_entry *mpt_entry, u32 pdn) { - u32 pd_flags = be32_to_cpu(mpt_entry->pd_flags); + u32 pd_flags = be32_to_cpu(mpt_entry->pd_flags) & ~MLX4_MPT_PD_MASK; /* The wrapper function will put the slave's id here */ if (mlx4_is_mfunc(dev)) pd_flags &= ~MLX4_MPT_PD_VF_MASK; - mpt_entry->pd_flags = cpu_to_be32((pd_flags & ~MLX4_MPT_PD_MASK) | + + mpt_entry->pd_flags = cpu_to_be32(pd_flags | (pdn & MLX4_MPT_PD_MASK) | MLX4_MPT_PD_FLAG_EN_INV); return 0; @@ -600,14 +599,18 @@ int mlx4_mr_rereg_mem_write(struct mlx4_dev *dev, struct mlx4_mr *mr, { int err; - mpt_entry->start = cpu_to_be64(mr->iova); - mpt_entry->length = cpu_to_be64(mr->size); - mpt_entry->entity_size = cpu_to_be32(mr->mtt.page_shift); + mpt_entry->start = cpu_to_be64(iova); + mpt_entry->length = cpu_to_be64(size); + mpt_entry->entity_size = cpu_to_be32(page_shift); err = mlx4_mtt_init(dev, npages, page_shift, &mr->mtt); if (err) return err; + mpt_entry->pd_flags &= cpu_to_be32(MLX4_MPT_PD_MASK | + MLX4_MPT_PD_FLAG_EN_INV); + mpt_entry->flags &= cpu_to_be32(MLX4_MPT_FLAG_FREE | + MLX4_MPT_FLAG_SW_OWNS); if (mr->mtt.order < 0) { mpt_entry->flags |= cpu_to_be32(MLX4_MPT_FLAG_PHYSICAL); mpt_entry->mtt_addr = 0; @@ -617,6 +620,14 @@ int mlx4_mr_rereg_mem_write(struct mlx4_dev *dev, struct mlx4_mr *mr, if (mr->mtt.page_shift == 0) mpt_entry->mtt_sz = cpu_to_be32(1 << mr->mtt.order); } + if (mr->mtt.order >= 0 && mr->mtt.page_shift == 0) { + /* fast register MR in free state */ + mpt_entry->flags |= cpu_to_be32(MLX4_MPT_FLAG_FREE); + mpt_entry->pd_flags |= cpu_to_be32(MLX4_MPT_PD_FLAG_FAST_REG | + MLX4_MPT_PD_FLAG_RAE); + } else { + mpt_entry->flags |= cpu_to_be32(MLX4_MPT_FLAG_SW_OWNS); + } mr->enabled = MLX4_MPT_EN_SW; return 0; -- cgit v1.2.1 From f4fd40b26bd597e203639281859a758402550d62 Mon Sep 17 00:00:00 2001 From: Jack Morgenstein Date: Thu, 11 Sep 2014 14:11:16 +0300 Subject: mlx4: Fix mlx4 reg/unreg mac to work properly with 0-mac addresses There is a chance that the VF mlx4 RoCE driver (mlx4_ib) may see a 0-mac as the current default MAC address when a RoCE interface first comes up. In this case, the RoCE driver registers the 0-mac to get its MAC index -- used in the INIT2RTR transition when it creates its proxy Q1 qp's. If we do not allow QP1 to be created, the RoCE driver will not come up. If we do not register the 0-mac, but simply use a random mac-index, QP1 will attempt to send packets with an someone's else source MAC which will get the system into more troubled. Since a 0-mac was previously used to indicate a free slot, this leads to errors, both when the 0-mac is registered and when it is unregistered. The required fix is to check in addition that the slot containing the 0-mac has a reference count of zero. Additionally, when comparing MAC addresses, need to mask out the 2 MSBs of the u64 mac on both sides of the comparison. Note that when the EN driver (mlx4_en) comes up, it set itself a proper mac --> the RoCE driver gets to be notified on that and further handing is done with the update qp command, as was added by commit 9433c188915c ("IB/mlx4: Invoke UPDATE_QP for proxy QP1 on MAC changes"). Signed-off-by: Jack Morgenstein Signed-off-by: Or Gerlitz Signed-off-by: Roland Dreier --- drivers/net/ethernet/mellanox/mlx4/port.c | 11 +++++++---- 1 file changed, 7 insertions(+), 4 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/mellanox/mlx4/port.c b/drivers/net/ethernet/mellanox/mlx4/port.c index 9ba0c1ca10d5..94eeb2c7d7e4 100644 --- a/drivers/net/ethernet/mellanox/mlx4/port.c +++ b/drivers/net/ethernet/mellanox/mlx4/port.c @@ -103,7 +103,8 @@ static int find_index(struct mlx4_dev *dev, int i; for (i = 0; i < MLX4_MAX_MAC_NUM; i++) { - if ((mac & MLX4_MAC_MASK) == + if (table->refs[i] && + (MLX4_MAC_MASK & mac) == (MLX4_MAC_MASK & be64_to_cpu(table->entries[i]))) return i; } @@ -165,12 +166,14 @@ int __mlx4_register_mac(struct mlx4_dev *dev, u8 port, u64 mac) mutex_lock(&table->mutex); for (i = 0; i < MLX4_MAX_MAC_NUM; i++) { - if (free < 0 && !table->entries[i]) { - free = i; + if (!table->refs[i]) { + if (free < 0) + free = i; continue; } - if (mac == (MLX4_MAC_MASK & be64_to_cpu(table->entries[i]))) { + if ((MLX4_MAC_MASK & mac) == + (MLX4_MAC_MASK & be64_to_cpu(table->entries[i]))) { /* MAC already registered, increment ref count */ err = i; ++table->refs[i]; -- cgit v1.2.1 From 4e5f9ef380b00871995d638c03e7ae7c67244e31 Mon Sep 17 00:00:00 2001 From: "David S. Miller" Date: Mon, 22 Sep 2014 13:25:51 -0400 Subject: pch_gbe: 'select' NET_PTP_CLASSIFY. MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Fixes the following randconfig build failure: > drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c: In function > ‘pch_ptp_match’: > drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c:130:2: error: > implicit declaration of function ‘ptp_classify_raw’ > [-Werror=implicit-function-declaration] > if (ptp_classify_raw(skb) == PTP_CLASS_NONE) > ^ > cc1: some warnings being treated as errors > make[5]: *** [drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.o] Error 1 Reported-by: Jim Davis Signed-off-by: David S. Miller --- drivers/net/ethernet/oki-semi/pch_gbe/Kconfig | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/oki-semi/pch_gbe/Kconfig b/drivers/net/ethernet/oki-semi/pch_gbe/Kconfig index 44c8be1c6805..5f7a35212796 100644 --- a/drivers/net/ethernet/oki-semi/pch_gbe/Kconfig +++ b/drivers/net/ethernet/oki-semi/pch_gbe/Kconfig @@ -7,6 +7,7 @@ config PCH_GBE depends on PCI && (X86_32 || COMPILE_TEST) select MII select PTP_1588_CLOCK_PCH + select NET_PTP_CLASSIFY ---help--- This is a gigabit ethernet driver for EG20T PCH. EG20T PCH is the platform controller hub that is used in Intel's -- cgit v1.2.1 From 476c18850c6cbaa3f2bb661ae9710645081563b9 Mon Sep 17 00:00:00 2001 From: Vlad Yasevich Date: Thu, 18 Sep 2014 10:31:17 -0400 Subject: tg3: Work around HW/FW limitations with vlan encapsulated frames TG3 appears to have an issue performing TSO and checksum offloading correclty when the frame has been vlan encapsulated (non-accelrated). In these cases, tcp checksum is not correctly updated. This patch attempts to work around this issue. After the patch, 802.1ad vlans start working correctly over tg3 devices. CC: Prashant Sreedharan CC: Michael Chan Signed-off-by: Vladislav Yasevich Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/tg3.c | 20 ++++++++++++++++++-- 1 file changed, 18 insertions(+), 2 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c index cb77ae93d89a..e7d3a620d96a 100644 --- a/drivers/net/ethernet/broadcom/tg3.c +++ b/drivers/net/ethernet/broadcom/tg3.c @@ -7914,8 +7914,6 @@ static netdev_tx_t tg3_start_xmit(struct sk_buff *skb, struct net_device *dev) entry = tnapi->tx_prod; base_flags = 0; - if (skb->ip_summed == CHECKSUM_PARTIAL) - base_flags |= TXD_FLAG_TCPUDP_CSUM; mss = skb_shinfo(skb)->gso_size; if (mss) { @@ -7929,6 +7927,13 @@ static netdev_tx_t tg3_start_xmit(struct sk_buff *skb, struct net_device *dev) hdr_len = skb_transport_offset(skb) + tcp_hdrlen(skb) - ETH_HLEN; + /* HW/FW can not correctly segment packets that have been + * vlan encapsulated. + */ + if (skb->protocol == htons(ETH_P_8021Q) || + skb->protocol == htons(ETH_P_8021AD)) + return tg3_tso_bug(tp, tnapi, txq, skb); + if (!skb_is_gso_v6(skb)) { if (unlikely((ETH_HLEN + hdr_len) > 80) && tg3_flag(tp, TSO_BUG)) @@ -7979,6 +7984,17 @@ static netdev_tx_t tg3_start_xmit(struct sk_buff *skb, struct net_device *dev) base_flags |= tsflags << 12; } } + } else if (skb->ip_summed == CHECKSUM_PARTIAL) { + /* HW/FW can not correctly checksum packets that have been + * vlan encapsulated. + */ + if (skb->protocol == htons(ETH_P_8021Q) || + skb->protocol == htons(ETH_P_8021AD)) { + if (skb_checksum_help(skb)) + goto drop; + } else { + base_flags |= TXD_FLAG_TCPUDP_CSUM; + } } if (tg3_flag(tp, USE_JUMBO_BDFLAG) && -- cgit v1.2.1 From 85911d71109d3dda8bb35515b78bcc1de6837785 Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Fri, 19 Sep 2014 13:40:25 +0300 Subject: r8169: fix an if condition There is an extra semi-colon so __rtl8169_set_features() is called every time. Fixes: 929a031dfd62 ('r8169: adjust __rtl8169_set_features') Signed-off-by: Dan Carpenter Acked-by: Hayes Wang -- Signed-off-by: David S. Miller --- drivers/net/ethernet/realtek/r8169.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index ef2cee5de62b..0921302553c6 100644 --- a/drivers/net/ethernet/realtek/r8169.c +++ b/drivers/net/ethernet/realtek/r8169.c @@ -1818,7 +1818,7 @@ static int rtl8169_set_features(struct net_device *dev, features &= NETIF_F_RXALL | NETIF_F_RXCSUM | NETIF_F_HW_VLAN_CTAG_RX; rtl_lock_work(tp); - if (features ^ dev->features); + if (features ^ dev->features) __rtl8169_set_features(dev, features); rtl_unlock_work(tp); -- cgit v1.2.1 From 09f3756bb9a82835b0c2a9b50f36b47aa42f2c61 Mon Sep 17 00:00:00 2001 From: Tobias Klauser Date: Fri, 19 Sep 2014 16:16:25 +0200 Subject: dm9000: Return an ERR_PTR() in all error conditions of dm9000_parse_dt() In one error condition dm9000_parse_dt() returns NULL, however the return value is checked using IS_ERR() in dm9000_probe(), leading to the error not being properly propagated if CONFIG_OF is not enabled or the device tree data is not available. Fix this by also returning an ERR_PTR() in this case. Fixes: 0b8bf1baabe5 (net: dm9000: Allow instantiation using device tree) Signed-off-by: Tobias Klauser Signed-off-by: David S. Miller --- drivers/net/ethernet/davicom/dm9000.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/davicom/dm9000.c b/drivers/net/ethernet/davicom/dm9000.c index 9b33057a9477..70089c29d307 100644 --- a/drivers/net/ethernet/davicom/dm9000.c +++ b/drivers/net/ethernet/davicom/dm9000.c @@ -1399,7 +1399,7 @@ static struct dm9000_plat_data *dm9000_parse_dt(struct device *dev) const void *mac_addr; if (!IS_ENABLED(CONFIG_OF) || !np) - return NULL; + return ERR_PTR(-ENXIO); pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL); if (!pdata) -- cgit v1.2.1 From 478a010c9235ca92e66cc5058b42e30e33275ad4 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Mon, 22 Sep 2014 11:54:42 -0700 Subject: net: bcmgenet: fix TX reclaim accounting for fragments The GENET driver supports SKB fragments, and succeeds in transmitting them properly, but when reclaiming these transmitted fragments, we will only update the count of free buffer descriptors by 1, even for SKBs with fragments. This leads to the networking stack thinking it has more room than the hardware has when pushing new SKBs, and backing off consequently because we return NETDEV_TX_BUSY. Fix this by accounting for the SKB nr_frags plus one (itself) and update ring->free_bds accordingly with that value for each iteration loop in __bcmgenet_tx_reclaim(). Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/genet/bcmgenet.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c index cdef86a03862..11a96437862d 100644 --- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c +++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c @@ -875,6 +875,7 @@ static void __bcmgenet_tx_reclaim(struct net_device *dev, int last_tx_cn, last_c_index, num_tx_bds; struct enet_cb *tx_cb_ptr; struct netdev_queue *txq; + unsigned int bds_compl; unsigned int c_index; /* Compute how many buffers are transmitted since last xmit call */ @@ -899,7 +900,9 @@ static void __bcmgenet_tx_reclaim(struct net_device *dev, /* Reclaim transmitted buffers */ while (last_tx_cn-- > 0) { tx_cb_ptr = ring->cbs + last_c_index; + bds_compl = 0; if (tx_cb_ptr->skb) { + bds_compl = skb_shinfo(tx_cb_ptr->skb)->nr_frags + 1; dev->stats.tx_bytes += tx_cb_ptr->skb->len; dma_unmap_single(&dev->dev, dma_unmap_addr(tx_cb_ptr, dma_addr), @@ -916,7 +919,7 @@ static void __bcmgenet_tx_reclaim(struct net_device *dev, dma_unmap_addr_set(tx_cb_ptr, dma_addr, 0); } dev->stats.tx_packets++; - ring->free_bds += 1; + ring->free_bds += bds_compl; last_c_index++; last_c_index &= (num_tx_bds - 1); -- cgit v1.2.1 From 4a0c081eff43a11c65dee3ad6c457f7f58bcebe0 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Mon, 22 Sep 2014 11:54:43 -0700 Subject: net: bcmgenet: call bcmgenet_dma_teardown in bcmgenet_fini_dma We should not be manipulaging the DMA_CTRL registers directly by writing 0 to them to disable DMA. This is an operation that needs to be timed to make sure the DMA engines have been properly stopped since their state machine stops on a packet boundary, not immediately. Make sure that tha bcmgenet_fini_dma() calls bcmgenet_dma_teardown() to ensure a proper DMA engine state. As a result, we need to reorder the function bodies to resolve the use dependency. Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/genet/bcmgenet.c | 105 ++++++++++++------------- 1 file changed, 52 insertions(+), 53 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/broadcom/genet/bcmgenet.c b/drivers/net/ethernet/broadcom/genet/bcmgenet.c index 11a96437862d..5cc9cae21ed5 100644 --- a/drivers/net/ethernet/broadcom/genet/bcmgenet.c +++ b/drivers/net/ethernet/broadcom/genet/bcmgenet.c @@ -1744,13 +1744,63 @@ static void bcmgenet_init_multiq(struct net_device *dev) bcmgenet_tdma_writel(priv, reg, DMA_CTRL); } +static int bcmgenet_dma_teardown(struct bcmgenet_priv *priv) +{ + int ret = 0; + int timeout = 0; + u32 reg; + + /* Disable TDMA to stop add more frames in TX DMA */ + reg = bcmgenet_tdma_readl(priv, DMA_CTRL); + reg &= ~DMA_EN; + bcmgenet_tdma_writel(priv, reg, DMA_CTRL); + + /* Check TDMA status register to confirm TDMA is disabled */ + while (timeout++ < DMA_TIMEOUT_VAL) { + reg = bcmgenet_tdma_readl(priv, DMA_STATUS); + if (reg & DMA_DISABLED) + break; + + udelay(1); + } + + if (timeout == DMA_TIMEOUT_VAL) { + netdev_warn(priv->dev, "Timed out while disabling TX DMA\n"); + ret = -ETIMEDOUT; + } + + /* Wait 10ms for packet drain in both tx and rx dma */ + usleep_range(10000, 20000); + + /* Disable RDMA */ + reg = bcmgenet_rdma_readl(priv, DMA_CTRL); + reg &= ~DMA_EN; + bcmgenet_rdma_writel(priv, reg, DMA_CTRL); + + timeout = 0; + /* Check RDMA status register to confirm RDMA is disabled */ + while (timeout++ < DMA_TIMEOUT_VAL) { + reg = bcmgenet_rdma_readl(priv, DMA_STATUS); + if (reg & DMA_DISABLED) + break; + + udelay(1); + } + + if (timeout == DMA_TIMEOUT_VAL) { + netdev_warn(priv->dev, "Timed out while disabling RX DMA\n"); + ret = -ETIMEDOUT; + } + + return ret; +} + static void bcmgenet_fini_dma(struct bcmgenet_priv *priv) { int i; /* disable DMA */ - bcmgenet_rdma_writel(priv, 0, DMA_CTRL); - bcmgenet_tdma_writel(priv, 0, DMA_CTRL); + bcmgenet_dma_teardown(priv); for (i = 0; i < priv->num_tx_bds; i++) { if (priv->tx_cbs[i].skb != NULL) { @@ -2109,57 +2159,6 @@ err_clk_disable: return ret; } -static int bcmgenet_dma_teardown(struct bcmgenet_priv *priv) -{ - int ret = 0; - int timeout = 0; - u32 reg; - - /* Disable TDMA to stop add more frames in TX DMA */ - reg = bcmgenet_tdma_readl(priv, DMA_CTRL); - reg &= ~DMA_EN; - bcmgenet_tdma_writel(priv, reg, DMA_CTRL); - - /* Check TDMA status register to confirm TDMA is disabled */ - while (timeout++ < DMA_TIMEOUT_VAL) { - reg = bcmgenet_tdma_readl(priv, DMA_STATUS); - if (reg & DMA_DISABLED) - break; - - udelay(1); - } - - if (timeout == DMA_TIMEOUT_VAL) { - netdev_warn(priv->dev, "Timed out while disabling TX DMA\n"); - ret = -ETIMEDOUT; - } - - /* Wait 10ms for packet drain in both tx and rx dma */ - usleep_range(10000, 20000); - - /* Disable RDMA */ - reg = bcmgenet_rdma_readl(priv, DMA_CTRL); - reg &= ~DMA_EN; - bcmgenet_rdma_writel(priv, reg, DMA_CTRL); - - timeout = 0; - /* Check RDMA status register to confirm RDMA is disabled */ - while (timeout++ < DMA_TIMEOUT_VAL) { - reg = bcmgenet_rdma_readl(priv, DMA_STATUS); - if (reg & DMA_DISABLED) - break; - - udelay(1); - } - - if (timeout == DMA_TIMEOUT_VAL) { - netdev_warn(priv->dev, "Timed out while disabling RX DMA\n"); - ret = -ETIMEDOUT; - } - - return ret; -} - static void bcmgenet_netif_stop(struct net_device *dev) { struct bcmgenet_priv *priv = netdev_priv(dev); -- cgit v1.2.1 From 4324414f8ccae4997dd1e91646683679a4436959 Mon Sep 17 00:00:00 2001 From: Sony Chacko Date: Mon, 22 Sep 2014 05:51:50 -0400 Subject: qlcnic: Use qlcnic_83xx_flash_read32() API instead of lockless version of the API. In qlcnic_83xx_setup_idc_parameters() routine use qlcnic_83xx_flash_read32() API which takes flash lock internally instead of the lockless version qlcnic_83xx_lockless_flash_read32(). Signed-off-by: Sony Chacko Signed-off-by: Manish Chopra Signed-off-by: David S. Miller --- drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_init.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_init.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_init.c index 86783e1afcf7..3172cdf591fe 100644 --- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_init.c +++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_init.c @@ -1177,9 +1177,8 @@ static void qlcnic_83xx_setup_idc_parameters(struct qlcnic_adapter *adapter) { u32 idc_params, val; - if (qlcnic_83xx_lockless_flash_read32(adapter, - QLC_83XX_IDC_FLASH_PARAM_ADDR, - (u8 *)&idc_params, 1)) { + if (qlcnic_83xx_flash_read32(adapter, QLC_83XX_IDC_FLASH_PARAM_ADDR, + (u8 *)&idc_params, 1)) { dev_info(&adapter->pdev->dev, "%s:failed to get IDC params from flash\n", __func__); adapter->dev_init_timeo = QLC_83XX_IDC_INIT_TIMEOUT_SECS; -- cgit v1.2.1 From c023030198b2b0fb87f5d9bcb388c41bfaf3c3c0 Mon Sep 17 00:00:00 2001 From: Manish Chopra Date: Mon, 22 Sep 2014 05:51:51 -0400 Subject: qlcnic: Fix memory corruption while reading stats using ethtool. o Driver is doing memset with zero for total number of stats bytes when it has already filled some data in the stats buffer, which can overwrite memory area beyond the length of stats buffer. o Fix this by initializing stats buffer with zero before filling any data in it. Signed-off-by: Manish Chopra Signed-off-by: David S. Miller --- drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c | 6 ++---- 1 file changed, 2 insertions(+), 4 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c index 141f116eb868..2d77b7694d16 100644 --- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c +++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c @@ -1333,12 +1333,11 @@ static void qlcnic_get_ethtool_stats(struct net_device *dev, struct qlcnic_host_tx_ring *tx_ring; struct qlcnic_esw_statistics port_stats; struct qlcnic_mac_statistics mac_stats; - int index, ret, length, size, tx_size, ring; + int index, ret, length, size, ring; char *p; - tx_size = adapter->drv_tx_rings * QLCNIC_TX_STATS_LEN; + memset(data, 0, stats->n_stats * sizeof(u64)); - memset(data, 0, tx_size * sizeof(u64)); for (ring = 0, index = 0; ring < adapter->drv_tx_rings; ring++) { if (test_bit(__QLCNIC_DEV_UP, &adapter->state)) { tx_ring = &adapter->tx_ring[ring]; @@ -1347,7 +1346,6 @@ static void qlcnic_get_ethtool_stats(struct net_device *dev, } } - memset(data, 0, stats->n_stats * sizeof(u64)); length = QLCNIC_STATS_LEN; for (index = 0; index < length; index++) { p = (char *)adapter + qlcnic_gstrings_stats[index].stat_offset; -- cgit v1.2.1 From 6c0fd0df0c44d1129ab65fc28d17f23a1c006a0c Mon Sep 17 00:00:00 2001 From: Manish Chopra Date: Mon, 22 Sep 2014 05:51:52 -0400 Subject: qlcnic: Remove __QLCNIC_DEV_UP bit check to read TX queues statistics. o TX queues stats must be read when queues are allocated regardless of interface is up or not. Signed-off-by: Manish Chopra Signed-off-by: David S. Miller --- drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c index 2d77b7694d16..863c4456d2d1 100644 --- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c +++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c @@ -1339,7 +1339,7 @@ static void qlcnic_get_ethtool_stats(struct net_device *dev, memset(data, 0, stats->n_stats * sizeof(u64)); for (ring = 0, index = 0; ring < adapter->drv_tx_rings; ring++) { - if (test_bit(__QLCNIC_DEV_UP, &adapter->state)) { + if (adapter->is_up == QLCNIC_ADAPTER_UP_MAGIC) { tx_ring = &adapter->tx_ring[ring]; data = qlcnic_fill_tx_queue_stats(data, tx_ring); qlcnic_update_stats(adapter); -- cgit v1.2.1 From 3456399b031c4bd71b90521301c646b62dfd0caa Mon Sep 17 00:00:00 2001 From: Manish Chopra Date: Mon, 22 Sep 2014 05:51:53 -0400 Subject: qlcnic: Fix ordering of stats in stats buffer. o When TX queues are not allocated, driver does not fill TX queues stats in the buffer. However, it is also not advancing data pointer by TX queue stats length, which would misplace all successive stats data in the buffer and will result in mismatch between stats strings and it's values. o Fix this by advancing data pointer by TX queue stats length when queues are not allocated. Signed-off-by: Manish Chopra Signed-off-by: David S. Miller --- drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c index 863c4456d2d1..494e8105adee 100644 --- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c +++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_ethtool.c @@ -1343,6 +1343,8 @@ static void qlcnic_get_ethtool_stats(struct net_device *dev, tx_ring = &adapter->tx_ring[ring]; data = qlcnic_fill_tx_queue_stats(data, tx_ring); qlcnic_update_stats(adapter); + } else { + data += QLCNIC_TX_STATS_LEN; } } -- cgit v1.2.1 From 9026968abe7ad102f4ac5c6d96d733643f75399c Mon Sep 17 00:00:00 2001 From: Soren Brinkmann Date: Mon, 22 Sep 2014 16:49:08 -0700 Subject: Revert "net/macb: add pinctrl consumer support" This reverts commit 8ef29f8aae524bd51298fb10ac6a5ce6c4c5a3d8. The driver core already calls pinctrl_get() and claims the default state. There is no need to replicate this in the driver. Acked-by: Nicolas Ferre Acked-by: Nicolas Ferre Signed-off-by: David S. Miller --- drivers/net/ethernet/cadence/macb.c | 11 ----------- 1 file changed, 11 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/cadence/macb.c b/drivers/net/ethernet/cadence/macb.c index ca5d7798b265..e1e02fba4fcc 100644 --- a/drivers/net/ethernet/cadence/macb.c +++ b/drivers/net/ethernet/cadence/macb.c @@ -30,7 +30,6 @@ #include #include #include -#include #include "macb.h" @@ -2071,7 +2070,6 @@ static int __init macb_probe(struct platform_device *pdev) struct phy_device *phydev; u32 config; int err = -ENXIO; - struct pinctrl *pinctrl; const char *mac; regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); @@ -2080,15 +2078,6 @@ static int __init macb_probe(struct platform_device *pdev) goto err_out; } - pinctrl = devm_pinctrl_get_select_default(&pdev->dev); - if (IS_ERR(pinctrl)) { - err = PTR_ERR(pinctrl); - if (err == -EPROBE_DEFER) - goto err_out; - - dev_warn(&pdev->dev, "No pinctrl provided\n"); - } - err = -ENOMEM; dev = alloc_etherdev(sizeof(*bp)); if (!dev) -- cgit v1.2.1 From effa4bc4e75a265105f4ccb55857057e5ad231ed Mon Sep 17 00:00:00 2001 From: Matan Barak Date: Tue, 23 Sep 2014 16:05:59 +0300 Subject: net/mlx4_core: Allow not to specify probe_vf in SRIOV IB mode When the HCA is configured in SRIOV IB mode (that is, at least one of the ports is IB) and the probe_vf module param isn't specified, mlx4_init_one() failed because of the following condition: if (ib_ports && (num_vfs_argc > 1 || probe_vfs_argc > 1)) { ..... } The root cause for that is a mistake in the initialization of num_vfs_argc and probe_vfs_argc. When num_vfs / probe_vf aren't given, their argument count counterpart should be 0, fix that. Fixes: dd41cc3bb90e ('net/mlx4: Adapt num_vfs/probed_vf params for single port VF') Signed-off-by: Matan Barak Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/main.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/mellanox/mlx4/main.c b/drivers/net/ethernet/mellanox/mlx4/main.c index 7e2d5d57c598..871e3a5bda38 100644 --- a/drivers/net/ethernet/mellanox/mlx4/main.c +++ b/drivers/net/ethernet/mellanox/mlx4/main.c @@ -78,13 +78,13 @@ MODULE_PARM_DESC(msi_x, "attempt to use MSI-X if nonzero"); #endif /* CONFIG_PCI_MSI */ static uint8_t num_vfs[3] = {0, 0, 0}; -static int num_vfs_argc = 3; +static int num_vfs_argc; module_param_array(num_vfs, byte , &num_vfs_argc, 0444); MODULE_PARM_DESC(num_vfs, "enable #num_vfs functions if num_vfs > 0\n" "num_vfs=port1,port2,port1+2"); static uint8_t probe_vf[3] = {0, 0, 0}; -static int probe_vfs_argc = 3; +static int probe_vfs_argc; module_param_array(probe_vf, byte, &probe_vfs_argc, 0444); MODULE_PARM_DESC(probe_vf, "number of vfs to probe by pf driver (num_vfs > 0)\n" "probe_vf=port1,port2,port1+2"); -- cgit v1.2.1 From c5bb86c3848174aad59ea6cf5748e210fbb8f744 Mon Sep 17 00:00:00 2001 From: "Kweh, Hock Leong" Date: Fri, 26 Sep 2014 21:42:55 +0800 Subject: net: stmmac: fix stmmac_pci_probe failed when CONFIG_HAVE_CLK is selected When the CONFIG_HAVE_CLK is selected for the system, the stmmac_pci_probe will fail with dmesg: [ 2.167225] stmmaceth 0000:00:14.6: enabling device (0000 -> 0002) [ 2.178267] stmmaceth 0000:00:14.6: enabling bus mastering [ 2.178436] stmmaceth 0000:00:14.6: irq 24 for MSI/MSI-X [ 2.178703] stmmaceth 0000:00:14.6: stmmac_dvr_probe: warning: cannot get CSR clock [ 2.186503] stmmac_pci_probe: main driver probe failed [ 2.194003] stmmaceth 0000:00:14.6: disabling bus mastering [ 2.196473] stmmaceth: probe of 0000:00:14.6 failed with error -2 This patch fix the issue by breaking the dependency to devm_clk_get() as the CSR clock can be obtained at priv->plat->clk_csr from pci driver. Reported-by: Tobias Klausmann Signed-off-by: Kweh, Hock Leong Signed-off-by: David S. Miller --- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index 6e6ee226de04..b0c1521e08a3 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -2786,8 +2786,15 @@ struct stmmac_priv *stmmac_dvr_probe(struct device *device, if (IS_ERR(priv->stmmac_clk)) { dev_warn(priv->device, "%s: warning: cannot get CSR clock\n", __func__); - ret = PTR_ERR(priv->stmmac_clk); - goto error_clk_get; + /* If failed to obtain stmmac_clk and specific clk_csr value + * is NOT passed from the platform, probe fail. + */ + if (!priv->plat->clk_csr) { + ret = PTR_ERR(priv->stmmac_clk); + goto error_clk_get; + } else { + priv->stmmac_clk = NULL; + } } clk_prepare_enable(priv->stmmac_clk); -- cgit v1.2.1 From 0d36882013e61dc47aa835c4ec98b1fe776c9db8 Mon Sep 17 00:00:00 2001 From: Manish Chopra Date: Tue, 30 Sep 2014 03:56:35 -0400 Subject: netxen: Fix BUG "sleeping function called from invalid context" o __netxen_nic_down() function might sleep while holding spinlock_t(tx_clean_lock). Acquire this lock for only releasing TX buffers instead of taking it for whole down path. Reported-by: Mike Galbraith Signed-off-by: Manish Chopra Signed-off-by: David S. Miller --- drivers/net/ethernet/qlogic/netxen/netxen_nic_init.c | 2 ++ drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c | 2 -- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/qlogic/netxen/netxen_nic_init.c b/drivers/net/ethernet/qlogic/netxen/netxen_nic_init.c index 32058614151a..ae4ec7b3bfd3 100644 --- a/drivers/net/ethernet/qlogic/netxen/netxen_nic_init.c +++ b/drivers/net/ethernet/qlogic/netxen/netxen_nic_init.c @@ -135,6 +135,7 @@ void netxen_release_tx_buffers(struct netxen_adapter *adapter) int i, j; struct nx_host_tx_ring *tx_ring = adapter->tx_ring; + spin_lock(&adapter->tx_clean_lock); cmd_buf = tx_ring->cmd_buf_arr; for (i = 0; i < tx_ring->num_desc; i++) { buffrag = cmd_buf->frag_array; @@ -158,6 +159,7 @@ void netxen_release_tx_buffers(struct netxen_adapter *adapter) } cmd_buf++; } + spin_unlock(&adapter->tx_clean_lock); } void netxen_free_sw_resources(struct netxen_adapter *adapter) diff --git a/drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c b/drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c index 1159031f885b..5ec5a2b0e989 100644 --- a/drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c +++ b/drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c @@ -1186,7 +1186,6 @@ __netxen_nic_down(struct netxen_adapter *adapter, struct net_device *netdev) return; smp_mb(); - spin_lock(&adapter->tx_clean_lock); netif_carrier_off(netdev); netif_tx_disable(netdev); @@ -1204,7 +1203,6 @@ __netxen_nic_down(struct netxen_adapter *adapter, struct net_device *netdev) netxen_napi_disable(adapter); netxen_release_tx_buffers(adapter); - spin_unlock(&adapter->tx_clean_lock); } /* Usage: During suspend and firmware recovery module */ -- cgit v1.2.1 From 9295f940fb677b343980cd67f3c91a4eb48d2fae Mon Sep 17 00:00:00 2001 From: Manish Chopra Date: Tue, 30 Sep 2014 03:56:36 -0400 Subject: netxen: Fix bug in Tx completion path. o Driver is not updating sw_consumer while processing Tx completion when interface is going down. Due to this interface down path gets stuck forever waiting for NAPI to complete. Signed-off-by: Manish Chopra Signed-off-by: David S. Miller --- drivers/net/ethernet/qlogic/netxen/netxen_nic_init.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/qlogic/netxen/netxen_nic_init.c b/drivers/net/ethernet/qlogic/netxen/netxen_nic_init.c index ae4ec7b3bfd3..5c4068353f66 100644 --- a/drivers/net/ethernet/qlogic/netxen/netxen_nic_init.c +++ b/drivers/net/ethernet/qlogic/netxen/netxen_nic_init.c @@ -1794,9 +1794,9 @@ int netxen_process_cmd_ring(struct netxen_adapter *adapter) break; } - if (count && netif_running(netdev)) { - tx_ring->sw_consumer = sw_consumer; + tx_ring->sw_consumer = sw_consumer; + if (count && netif_running(netdev)) { smp_mb(); if (netif_queue_stopped(netdev) && netif_carrier_ok(netdev)) -- cgit v1.2.1 From 7d3083ee36b51e425b6abd76778a2046906b0fd3 Mon Sep 17 00:00:00 2001 From: Vlad Yasevich Date: Tue, 30 Sep 2014 19:39:36 -0400 Subject: tg3: Allow for recieve of full-size 8021AD frames When receiving a vlan-tagged frame that still contains a vlan header, the length of the packet will be greater then MTU+ETH_HLEN since it will account of the extra vlan header. TG3 checks this for the case for 802.1Q, but not for 802.1ad. As a result, full sized 802.1ad frames get dropped by the card. Add a check for 802.1ad protocol when receving full sized frames. Suggested-by: Prashant Sreedharan CC: Prashant Sreedharan CC: Michael Chan Signed-off-by: Vladislav Yasevich Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/tg3.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c index e7d3a620d96a..ba499489969a 100644 --- a/drivers/net/ethernet/broadcom/tg3.c +++ b/drivers/net/ethernet/broadcom/tg3.c @@ -6918,7 +6918,8 @@ static int tg3_rx(struct tg3_napi *tnapi, int budget) skb->protocol = eth_type_trans(skb, tp->dev); if (len > (tp->dev->mtu + ETH_HLEN) && - skb->protocol != htons(ETH_P_8021Q)) { + skb->protocol != htons(ETH_P_8021Q) && + skb->protocol != htons(ETH_P_8021AD)) { dev_kfree_skb_any(skb); goto drop_it_no_recycle; } -- cgit v1.2.1 From 1b0ecb28b0cc216535ce6477d39aa610c3ff68a1 Mon Sep 17 00:00:00 2001 From: Vlad Yasevich Date: Tue, 30 Sep 2014 19:39:37 -0400 Subject: bnx2: Correctly receive full sized 802.1ad fragmes This driver, similar to tg3, has a check that will cause full sized 802.1ad frames to be dropped. The frame will be larger then the standard mtu due to the presense of vlan header that has not been stripped. The driver should not drop this frame and should process it just like it does for 802.1q. CC: Sony Chacko CC: Dept-HSGLinuxNICDev@qlogic.com Signed-off-by: Vladislav Yasevich Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/bnx2.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/broadcom/bnx2.c b/drivers/net/ethernet/broadcom/bnx2.c index 2fee73b878c2..823d01c5684c 100644 --- a/drivers/net/ethernet/broadcom/bnx2.c +++ b/drivers/net/ethernet/broadcom/bnx2.c @@ -3236,8 +3236,9 @@ bnx2_rx_int(struct bnx2 *bp, struct bnx2_napi *bnapi, int budget) skb->protocol = eth_type_trans(skb, bp->dev); - if ((len > (bp->dev->mtu + ETH_HLEN)) && - (ntohs(skb->protocol) != 0x8100)) { + if (len > (bp->dev->mtu + ETH_HLEN) && + skb->protocol != htons(0x8100) && + skb->protocol != htons(ETH_P_8021AD)) { dev_kfree_skb(skb); goto next_rx; -- cgit v1.2.1