From fb8ef788680d48523321e5f150b23700a1caf980 Mon Sep 17 00:00:00 2001 From: Duan Fugang-B38611 Date: Thu, 20 Feb 2014 18:14:39 +0800 Subject: net: fec: fix potential issue to avoid fec interrupt lost and crc error The current flow: Set TX BD ready, and then set "INT" and "PINS" bit to enable tx interrupt generation and crc checksum. There has potential issue like as: CPU fec uDMA Set tx ready bit uDMA start the BD transmission Set "INT" bit Set "PINS" bit ... Above situation cause fec tx interrupt lost and fec MAC don't do CRC checksum. The patch fix the potential issue. Signed-off-by: Fugang Duan Acked-by: Frank Li Signed-off-by: David S. Miller --- drivers/net/ethernet/freescale/fec_main.c | 13 +++++++------ 1 file changed, 7 insertions(+), 6 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c index 903362a7b584..479a7cba45c0 100644 --- a/drivers/net/ethernet/freescale/fec_main.c +++ b/drivers/net/ethernet/freescale/fec_main.c @@ -389,12 +389,6 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *ndev) netdev_err(ndev, "Tx DMA memory map failed\n"); return NETDEV_TX_OK; } - /* Send it on its way. Tell FEC it's ready, interrupt when done, - * it's the last BD of the frame, and to put the CRC on the end. - */ - status |= (BD_ENET_TX_READY | BD_ENET_TX_INTR - | BD_ENET_TX_LAST | BD_ENET_TX_TC); - bdp->cbd_sc = status; if (fep->bufdesc_ex) { @@ -416,6 +410,13 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *ndev) } } + /* Send it on its way. Tell FEC it's ready, interrupt when done, + * it's the last BD of the frame, and to put the CRC on the end. + */ + status |= (BD_ENET_TX_READY | BD_ENET_TX_INTR + | BD_ENET_TX_LAST | BD_ENET_TX_TC); + bdp->cbd_sc = status; + bdp_pre = fec_enet_get_prevdesc(bdp, fep); if ((id_entry->driver_data & FEC_QUIRK_ERR006358) && !(bdp_pre->cbd_sc & BD_ENET_TX_READY)) { -- cgit v1.2.1 From 7262b7b26de1495f77edbe1e71cb15b8198adb9d Mon Sep 17 00:00:00 2001 From: Tobias Klauser Date: Sat, 22 Feb 2014 13:09:03 +0100 Subject: net: stmmac: Check return value of alloc_dma_desc_resources() alloc_dma_desc_resources() returns an error value and the next line actually checks for it, so assign the return value properly. Found by the coverity scanner. Signed-off-by: Tobias Klauser Acked-by: Giuseppe Cavallaro Signed-off-by: David S. Miller --- drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index a2e7d2c96e36..078ad0ec8593 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -1705,7 +1705,7 @@ static int stmmac_open(struct net_device *dev) priv->dma_rx_size = STMMAC_ALIGN(dma_rxsize); priv->dma_buf_sz = STMMAC_ALIGN(buf_sz); - alloc_dma_desc_resources(priv); + ret = alloc_dma_desc_resources(priv); if (ret < 0) { pr_err("%s: DMA descriptors allocation failed\n", __func__); goto dma_desc_error; -- cgit v1.2.1 From 340fea3d7f6a2657ddd0b48413cd81e8513357ed Mon Sep 17 00:00:00 2001 From: Kyle McMartin Date: Mon, 24 Feb 2014 20:12:28 -0500 Subject: r8169: initialize rtl8169_stats seqlock Boris reports he's seeing: > [ 9.195943] INFO: trying to register non-static key. > [ 9.196031] the code is fine but needs lockdep annotation. > [ 9.196031] turning off the locking correctness validator. > [ 9.196031] CPU: 1 PID: 933 Comm: modprobe Not tainted 3.14.0-rc4+ #1 with the r8169 driver. These are occuring because the seqcount embedded in u64_stats_sync on 32-bit SMP is uninitialized which is making lockdep unhappy. Signed-off-by: Kyle McMartin Signed-off-by: David S. Miller --- drivers/net/ethernet/realtek/r8169.c | 2 ++ 1 file changed, 2 insertions(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index 91a67ae8f17b..e9779653cd4c 100644 --- a/drivers/net/ethernet/realtek/r8169.c +++ b/drivers/net/ethernet/realtek/r8169.c @@ -7118,6 +7118,8 @@ rtl_init_one(struct pci_dev *pdev, const struct pci_device_id *ent) } mutex_init(&tp->wk.mutex); + u64_stats_init(&tp->rx_stats.syncp); + u64_stats_init(&tp->tx_stats.syncp); /* Get MAC address */ for (i = 0; i < ETH_ALEN; i++) -- cgit v1.2.1 From 169a1d85d084edeb0736ad80fe439639ac938dcd Mon Sep 17 00:00:00 2001 From: Amir Vadai Date: Wed, 19 Feb 2014 17:47:31 +0200 Subject: net,IB/mlx: Bump all Mellanox driver versions Bump all Mellanox driver versions. Signed-off-by: Amir Vadai Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/mlx4.h | 4 ++-- drivers/net/ethernet/mellanox/mlx4/mlx4_en.h | 4 ++-- drivers/net/ethernet/mellanox/mlx5/core/main.c | 4 ++-- 3 files changed, 6 insertions(+), 6 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/mellanox/mlx4/mlx4.h b/drivers/net/ethernet/mellanox/mlx4/mlx4.h index 6b65f7795215..7aec6c833973 100644 --- a/drivers/net/ethernet/mellanox/mlx4/mlx4.h +++ b/drivers/net/ethernet/mellanox/mlx4/mlx4.h @@ -51,8 +51,8 @@ #define DRV_NAME "mlx4_core" #define PFX DRV_NAME ": " -#define DRV_VERSION "1.1" -#define DRV_RELDATE "Dec, 2011" +#define DRV_VERSION "2.2-1" +#define DRV_RELDATE "Feb, 2014" #define MLX4_FS_UDP_UC_EN (1 << 1) #define MLX4_FS_TCP_UC_EN (1 << 2) diff --git a/drivers/net/ethernet/mellanox/mlx4/mlx4_en.h b/drivers/net/ethernet/mellanox/mlx4/mlx4_en.h index 9ca223bc90fc..b57e8c87a34e 100644 --- a/drivers/net/ethernet/mellanox/mlx4/mlx4_en.h +++ b/drivers/net/ethernet/mellanox/mlx4/mlx4_en.h @@ -57,8 +57,8 @@ #include "en_port.h" #define DRV_NAME "mlx4_en" -#define DRV_VERSION "2.0" -#define DRV_RELDATE "Dec 2011" +#define DRV_VERSION "2.2-1" +#define DRV_RELDATE "Feb 2014" #define MLX4_EN_MSG_LEVEL (NETIF_MSG_LINK | NETIF_MSG_IFDOWN) diff --git a/drivers/net/ethernet/mellanox/mlx5/core/main.c b/drivers/net/ethernet/mellanox/mlx5/core/main.c index a064f06e0cb8..23b7e2d35a93 100644 --- a/drivers/net/ethernet/mellanox/mlx5/core/main.c +++ b/drivers/net/ethernet/mellanox/mlx5/core/main.c @@ -46,8 +46,8 @@ #include "mlx5_core.h" #define DRIVER_NAME "mlx5_core" -#define DRIVER_VERSION "1.0" -#define DRIVER_RELDATE "June 2013" +#define DRIVER_VERSION "2.2-1" +#define DRIVER_RELDATE "Feb 2014" MODULE_AUTHOR("Eli Cohen "); MODULE_DESCRIPTION("Mellanox ConnectX-IB HCA core library"); -- cgit v1.2.1 From fc49beaee2a410402f49fd21c81a37a863b7a9ba Mon Sep 17 00:00:00 2001 From: Shahed Shaikh Date: Mon, 24 Feb 2014 08:54:46 -0500 Subject: qlcnic: Fix function return error check Driver was treating -ve return value as success in case of qlcnic_enable_msi_legacy() failure Signed-off-by: Shahed Shaikh Signed-off-by: David S. Miller --- drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c index ba78c7481fa3..149c4b6d340b 100644 --- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c +++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c @@ -818,7 +818,7 @@ static int qlcnic_82xx_setup_intr(struct qlcnic_adapter *adapter) qlcnic_disable_multi_tx(adapter); err = qlcnic_enable_msi_legacy(adapter); - if (!err) + if (err) return err; } } -- cgit v1.2.1 From b7520d2b59b09eb284e5fc9080d13145f0a8d9fd Mon Sep 17 00:00:00 2001 From: Shahed Shaikh Date: Mon, 24 Feb 2014 08:54:47 -0500 Subject: qlcnic: Fix usage of use_msi and use_msi_x module parameters Once interrupts are enabled, instead of using module parameters, use flags (QLCNIC_MSI_ENABLED and QLCNIC_MSIX_ENABLED) set by driver to check interrupt mode. Signed-off-by: Shahed Shaikh Signed-off-by: David S. Miller --- drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c index 149c4b6d340b..e10fc8e7fe22 100644 --- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c +++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c @@ -3863,7 +3863,7 @@ int qlcnic_validate_rings(struct qlcnic_adapter *adapter, __u32 ring_cnt, strcpy(buf, "Tx"); } - if (!qlcnic_use_msi_x && !qlcnic_use_msi) { + if (!QLCNIC_IS_MSI_FAMILY(adapter)) { netdev_err(netdev, "No RSS/TSS support in INT-x mode\n"); return -EINVAL; } -- cgit v1.2.1 From 46428228b55df144f04cbad023907c177aa00d5f Mon Sep 17 00:00:00 2001 From: Sucheta Chakraborty Date: Mon, 24 Feb 2014 08:54:48 -0500 Subject: qlcnic: Allow any VLAN to be configured from VF. o This patch reverts commit 1414abea048e0835c43600d62808ed8163897227 (qlcnic: Restrict VF from configuring any VLAN mode.) This will allow same multicast address to be used with any VLAN instead of programming seperate (MAC, VLAN) tuples in adapter. This will help save some multicast filters. Signed-off-by: Sucheta Chakraborty Signed-off-by: David S. Miller --- drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c | 9 --------- 1 file changed, 9 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c index 09acf15c3a56..e5277a632671 100644 --- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c +++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c @@ -13,8 +13,6 @@ #define QLC_VF_MIN_TX_RATE 100 #define QLC_VF_MAX_TX_RATE 9999 #define QLC_MAC_OPCODE_MASK 0x7 -#define QLC_MAC_STAR_ADD 6 -#define QLC_MAC_STAR_DEL 7 #define QLC_VF_FLOOD_BIT BIT_16 #define QLC_FLOOD_MODE 0x5 @@ -1206,13 +1204,6 @@ static int qlcnic_sriov_validate_cfg_macvlan(struct qlcnic_adapter *adapter, struct qlcnic_vport *vp = vf->vp; u8 op, new_op; - if (((cmd->req.arg[1] & QLC_MAC_OPCODE_MASK) == QLC_MAC_STAR_ADD) || - ((cmd->req.arg[1] & QLC_MAC_OPCODE_MASK) == QLC_MAC_STAR_DEL)) { - netdev_err(adapter->netdev, "MAC + any VLAN filter not allowed from VF %d\n", - vf->pci_func); - return -EINVAL; - } - if (!(cmd->req.arg[1] & BIT_8)) return -EINVAL; -- cgit v1.2.1 From 42beb3f2836a6063ceb8134dbac0e32df1deea26 Mon Sep 17 00:00:00 2001 From: Rajesh Borundia Date: Mon, 24 Feb 2014 08:54:49 -0500 Subject: qlcnic: Fix number of rings when we fall back from msix to legacy. o Driver was not re-setting sds ring count to 1 after failing to allocate msi-x interrupts. Signed-off-by: Rajesh Borundia Signed-off-by: David S. Miller --- drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c | 1 + drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c | 1 + 2 files changed, 2 insertions(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c index 4146664d4d6a..27c4f131863b 100644 --- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c +++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_83xx_hw.c @@ -340,6 +340,7 @@ int qlcnic_83xx_setup_intr(struct qlcnic_adapter *adapter) if (qlcnic_sriov_vf_check(adapter)) return -EINVAL; num_msix = 1; + adapter->drv_sds_rings = QLCNIC_SINGLE_RING; adapter->drv_tx_rings = QLCNIC_SINGLE_RING; } } diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c index e10fc8e7fe22..1222865cfb73 100644 --- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c +++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c @@ -816,6 +816,7 @@ static int qlcnic_82xx_setup_intr(struct qlcnic_adapter *adapter) if (!(adapter->flags & QLCNIC_MSIX_ENABLED)) { qlcnic_disable_multi_tx(adapter); + adapter->drv_sds_rings = QLCNIC_SINGLE_RING; err = qlcnic_enable_msi_legacy(adapter); if (err) -- cgit v1.2.1 From 687d705c031916b83953b714917b04d899e23cf5 Mon Sep 17 00:00:00 2001 From: Thadeu Lima de Souza Cascardo Date: Mon, 24 Feb 2014 17:04:52 -0300 Subject: net/cxgb4: use remove handler as shutdown handler Without a shutdown handler, T4 cards behave very badly after a kexec. Some firmware calls return errors indicating allocation failures, for example. This is probably because thouse resources were not released by a BYE message to the firmware, for example. Using the remove handler guarantees we will use a well tested path. With this patch I applied, I managed to use kexec multiple times and probe and iSCSI login worked every time. Signed-off-by: Thadeu Lima de Souza Cascardo Signed-off-by: David S. Miller --- drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c index 43ab35fea48d..34e2488767d9 100644 --- a/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c +++ b/drivers/net/ethernet/chelsio/cxgb4/cxgb4_main.c @@ -6179,6 +6179,7 @@ static struct pci_driver cxgb4_driver = { .id_table = cxgb4_pci_tbl, .probe = init_one, .remove = remove_one, + .shutdown = remove_one, .err_handler = &cxgb4_eeh, }; -- cgit v1.2.1 From 8f355e5cee63c2c0c145d8206c4245d0189f47ff Mon Sep 17 00:00:00 2001 From: Edward Cree Date: Tue, 25 Feb 2014 13:17:59 +0000 Subject: sfc: check for NULL efx->ptp_data in efx_ptp_event If we receive a PTP event from the NIC when we haven't set up PTP state in the driver, we attempt to read through a NULL pointer efx->ptp_data, triggering a panic. Signed-off-by: Edward Cree Acked-by: Shradha Shah Signed-off-by: David S. Miller --- drivers/net/ethernet/sfc/ptp.c | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/sfc/ptp.c b/drivers/net/ethernet/sfc/ptp.c index eb75fbd11a01..d7a36829649a 100644 --- a/drivers/net/ethernet/sfc/ptp.c +++ b/drivers/net/ethernet/sfc/ptp.c @@ -1668,6 +1668,13 @@ void efx_ptp_event(struct efx_nic *efx, efx_qword_t *ev) struct efx_ptp_data *ptp = efx->ptp_data; int code = EFX_QWORD_FIELD(*ev, MCDI_EVENT_CODE); + if (!ptp) { + if (net_ratelimit()) + netif_warn(efx, drv, efx->net_dev, + "Received PTP event but PTP not set up\n"); + return; + } + if (!ptp->enabled) return; -- cgit v1.2.1 From babe723d6d733a1045bb44ab82fbe27bdfa2bff8 Mon Sep 17 00:00:00 2001 From: Yuval Mintz Date: Thu, 27 Feb 2014 15:42:26 +0200 Subject: bnx2x: Add missing bit in default Tx switching Commit c14db2025 "bnx2x: Correct default Tx switching behaviour" supposedly changed the default Tx switching behaviour, but was missing the fastpath change required for FW to pass packets from PFs to VFs. Signed-off-by: Yuval Mintz Signed-off-by: Ariel Elior Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c index 66c0df78c3ff..dbcff509dc3f 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c @@ -3875,7 +3875,9 @@ netdev_tx_t bnx2x_start_xmit(struct sk_buff *skb, struct net_device *dev) xmit_type); } - /* Add the macs to the parsing BD this is a vf */ + /* Add the macs to the parsing BD if this is a vf or if + * Tx Switching is enabled. + */ if (IS_VF(bp)) { /* override GRE parameters in BD */ bnx2x_set_fw_mac_addr(&pbd_e2->data.mac_addr.src_hi, @@ -3883,6 +3885,11 @@ netdev_tx_t bnx2x_start_xmit(struct sk_buff *skb, struct net_device *dev) &pbd_e2->data.mac_addr.src_lo, eth->h_source); + bnx2x_set_fw_mac_addr(&pbd_e2->data.mac_addr.dst_hi, + &pbd_e2->data.mac_addr.dst_mid, + &pbd_e2->data.mac_addr.dst_lo, + eth->h_dest); + } else if (bp->flags & TX_SWITCHING) { bnx2x_set_fw_mac_addr(&pbd_e2->data.mac_addr.dst_hi, &pbd_e2->data.mac_addr.dst_mid, &pbd_e2->data.mac_addr.dst_lo, -- cgit v1.2.1 From d7b95315cc7f441418845a165ee56df723941487 Mon Sep 17 00:00:00 2001 From: Michael Chan Date: Fri, 28 Feb 2014 15:05:10 -0800 Subject: tg3: Don't check undefined error bits in RXBD Redefine the RXD_ERR_MASK to include only relevant error bits. This fixes a customer reported issue of randomly dropping packets on the 5719. Signed-off-by: Michael Chan Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/tg3.c | 3 +-- drivers/net/ethernet/broadcom/tg3.h | 6 +++++- 2 files changed, 6 insertions(+), 3 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c index 3167ed6593b0..3b6d0ba86c71 100644 --- a/drivers/net/ethernet/broadcom/tg3.c +++ b/drivers/net/ethernet/broadcom/tg3.c @@ -6843,8 +6843,7 @@ static int tg3_rx(struct tg3_napi *tnapi, int budget) work_mask |= opaque_key; - if ((desc->err_vlan & RXD_ERR_MASK) != 0 && - (desc->err_vlan != RXD_ERR_ODD_NIBBLE_RCVD_MII)) { + if (desc->err_vlan & RXD_ERR_MASK) { drop_it: tg3_recycle_rx(tnapi, tpr, opaque_key, desc_idx, *post_ptr); diff --git a/drivers/net/ethernet/broadcom/tg3.h b/drivers/net/ethernet/broadcom/tg3.h index ef472385bce4..04321e5a356e 100644 --- a/drivers/net/ethernet/broadcom/tg3.h +++ b/drivers/net/ethernet/broadcom/tg3.h @@ -2608,7 +2608,11 @@ struct tg3_rx_buffer_desc { #define RXD_ERR_TOO_SMALL 0x00400000 #define RXD_ERR_NO_RESOURCES 0x00800000 #define RXD_ERR_HUGE_FRAME 0x01000000 -#define RXD_ERR_MASK 0xffff0000 + +#define RXD_ERR_MASK (RXD_ERR_BAD_CRC | RXD_ERR_COLLISION | \ + RXD_ERR_LINK_LOST | RXD_ERR_PHY_DECODE | \ + RXD_ERR_MAC_ABRT | RXD_ERR_TOO_SMALL | \ + RXD_ERR_NO_RESOURCES | RXD_ERR_HUGE_FRAME) u32 reserved; u32 opaque; -- cgit v1.2.1 From 877767dccf5c35d4ed245701956effb72af77d52 Mon Sep 17 00:00:00 2001 From: Ivan Vecera Date: Fri, 28 Feb 2014 14:14:03 +0100 Subject: bna: fix vlan tag stripping and implement its toggling The recent commit "fe1624c bna: RX Filter Enhancements" disables VLAN tag stripping if the NIC is in promiscuous mode. This causes __vlan_hwaccel_put_tag() is called when the stripping is disabled. Because of this VLAN over bna does not work and causes BUGs in conjunction with openvswitch like this: Reviewed-by: Jiri Pirko Signed-off-by: David S. Miller --- drivers/net/ethernet/brocade/bna/bnad.c | 40 ++++++++++++++++++++++++--------- 1 file changed, 30 insertions(+), 10 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/brocade/bna/bnad.c b/drivers/net/ethernet/brocade/bna/bnad.c index cf64f3d0b60d..4ad1187e82fb 100644 --- a/drivers/net/ethernet/brocade/bna/bnad.c +++ b/drivers/net/ethernet/brocade/bna/bnad.c @@ -707,7 +707,8 @@ bnad_cq_process(struct bnad *bnad, struct bna_ccb *ccb, int budget) else skb_checksum_none_assert(skb); - if (flags & BNA_CQ_EF_VLAN) + if ((flags & BNA_CQ_EF_VLAN) && + (bnad->netdev->features & NETIF_F_HW_VLAN_CTAG_RX)) __vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q), ntohs(cmpl->vlan_tag)); if (BNAD_RXBUF_IS_SK_BUFF(unmap_q->type)) @@ -2094,7 +2095,9 @@ bnad_init_rx_config(struct bnad *bnad, struct bna_rx_config *rx_config) rx_config->q1_buf_size = BFI_SMALL_RXBUF_SIZE; } - rx_config->vlan_strip_status = BNA_STATUS_T_ENABLED; + rx_config->vlan_strip_status = + (bnad->netdev->features & NETIF_F_HW_VLAN_CTAG_RX) ? + BNA_STATUS_T_ENABLED : BNA_STATUS_T_DISABLED; } static void @@ -3245,11 +3248,6 @@ bnad_set_rx_mode(struct net_device *netdev) BNA_RXMODE_ALLMULTI; bna_rx_mode_set(bnad->rx_info[0].rx, new_mode, mode_mask, NULL); - if (bnad->cfg_flags & BNAD_CF_PROMISC) - bna_rx_vlan_strip_disable(bnad->rx_info[0].rx); - else - bna_rx_vlan_strip_enable(bnad->rx_info[0].rx); - spin_unlock_irqrestore(&bnad->bna_lock, flags); } @@ -3374,6 +3372,27 @@ bnad_vlan_rx_kill_vid(struct net_device *netdev, __be16 proto, u16 vid) return 0; } +static int bnad_set_features(struct net_device *dev, netdev_features_t features) +{ + struct bnad *bnad = netdev_priv(dev); + netdev_features_t changed = features ^ dev->features; + + if ((changed & NETIF_F_HW_VLAN_CTAG_RX) && netif_running(dev)) { + unsigned long flags; + + spin_lock_irqsave(&bnad->bna_lock, flags); + + if (features & NETIF_F_HW_VLAN_CTAG_RX) + bna_rx_vlan_strip_enable(bnad->rx_info[0].rx); + else + bna_rx_vlan_strip_disable(bnad->rx_info[0].rx); + + spin_unlock_irqrestore(&bnad->bna_lock, flags); + } + + return 0; +} + #ifdef CONFIG_NET_POLL_CONTROLLER static void bnad_netpoll(struct net_device *netdev) @@ -3421,6 +3440,7 @@ static const struct net_device_ops bnad_netdev_ops = { .ndo_change_mtu = bnad_change_mtu, .ndo_vlan_rx_add_vid = bnad_vlan_rx_add_vid, .ndo_vlan_rx_kill_vid = bnad_vlan_rx_kill_vid, + .ndo_set_features = bnad_set_features, #ifdef CONFIG_NET_POLL_CONTROLLER .ndo_poll_controller = bnad_netpoll #endif @@ -3433,14 +3453,14 @@ bnad_netdev_init(struct bnad *bnad, bool using_dac) netdev->hw_features = NETIF_F_SG | NETIF_F_RXCSUM | NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM | - NETIF_F_TSO | NETIF_F_TSO6 | NETIF_F_HW_VLAN_CTAG_TX; + NETIF_F_TSO | NETIF_F_TSO6 | NETIF_F_HW_VLAN_CTAG_TX | + NETIF_F_HW_VLAN_CTAG_RX; netdev->vlan_features = NETIF_F_SG | NETIF_F_HIGHDMA | NETIF_F_IP_CSUM | NETIF_F_IPV6_CSUM | NETIF_F_TSO | NETIF_F_TSO6; - netdev->features |= netdev->hw_features | - NETIF_F_HW_VLAN_CTAG_RX | NETIF_F_HW_VLAN_CTAG_FILTER; + netdev->features |= netdev->hw_features | NETIF_F_HW_VLAN_CTAG_FILTER; if (using_dac) netdev->features |= NETIF_F_HIGHDMA; -- cgit v1.2.1 From 25d54fe5657f74766f2c79ad1267320793403f9e Mon Sep 17 00:00:00 2001 From: Hauke Mehrtens Date: Sun, 2 Mar 2014 17:29:33 +0100 Subject: b44: add calls to phy_{start,stop} When support for external phys was added to b44, the calls to start and stop the phy were missing in the mac driver. This adds the calls to phy_start() and phy_stop(). Signed-off-by: Hauke Mehrtens Acked-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/b44.c | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/broadcom/b44.c b/drivers/net/ethernet/broadcom/b44.c index 1f7b5aa114fa..e8046e1ebd1c 100644 --- a/drivers/net/ethernet/broadcom/b44.c +++ b/drivers/net/ethernet/broadcom/b44.c @@ -1484,6 +1484,10 @@ static int b44_open(struct net_device *dev) add_timer(&bp->timer); b44_enable_ints(bp); + + if (bp->flags & B44_FLAG_EXTERNAL_PHY) + phy_start(bp->phydev); + netif_start_queue(dev); out: return err; @@ -1646,6 +1650,9 @@ static int b44_close(struct net_device *dev) netif_stop_queue(dev); + if (bp->flags & B44_FLAG_EXTERNAL_PHY) + phy_stop(bp->phydev); + napi_disable(&bp->napi); del_timer_sync(&bp->timer); -- cgit v1.2.1 From 1d3f41ea0e95bed0502a7ac3f42fdc23ca6b7b82 Mon Sep 17 00:00:00 2001 From: Hauke Mehrtens Date: Sun, 2 Mar 2014 17:29:34 +0100 Subject: b44: always set duplex mode why phy changes Without this patch b44_check_phy() was called when the phy called the adjust callback. This method only change the mac duplex mode when the carrier was off. When the phy changed the duplex mode after the carrier was on the mac was not changed. This happened when an external phy was used. Signed-off-by: Hauke Mehrtens Acked-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/b44.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/broadcom/b44.c b/drivers/net/ethernet/broadcom/b44.c index e8046e1ebd1c..8a7bf7dad898 100644 --- a/drivers/net/ethernet/broadcom/b44.c +++ b/drivers/net/ethernet/broadcom/b44.c @@ -2229,7 +2229,12 @@ static void b44_adjust_link(struct net_device *dev) } if (status_changed) { - b44_check_phy(bp); + u32 val = br32(bp, B44_TX_CTRL); + if (bp->flags & B44_FLAG_FULL_DUPLEX) + val |= TX_CTRL_DUPLEX; + else + val &= ~TX_CTRL_DUPLEX; + bw32(bp, B44_TX_CTRL, val); phy_print_status(phydev); } } -- cgit v1.2.1 From e842b068bf9a9eb7b38e0e1875357440a1fd2169 Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Sat, 1 Mar 2014 16:54:36 +0300 Subject: qlcnic: dcb: a couple off by one bugs The ->tc_cfg[] array has QLC_DCB_MAX_TC (8) elements so the check is off by one. These functions are always called with valid values though so it doesn't affect how the code works. Signed-off-by: Dan Carpenter Acked-by: Sucheta Chakraborty Signed-off-by: David S. Miller --- drivers/net/ethernet/qlogic/qlcnic/qlcnic_dcb.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_dcb.c b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_dcb.c index 77f1bce432d2..7d4f54912bad 100644 --- a/drivers/net/ethernet/qlogic/qlcnic/qlcnic_dcb.c +++ b/drivers/net/ethernet/qlogic/qlcnic/qlcnic_dcb.c @@ -807,7 +807,7 @@ qlcnic_dcb_get_pg_tc_cfg_tx(struct net_device *netdev, int tc, u8 *prio, !type->tc_param_valid) return; - if (tc < 0 || (tc > QLC_DCB_MAX_TC)) + if (tc < 0 || (tc >= QLC_DCB_MAX_TC)) return; tc_cfg = &type->tc_cfg[tc]; @@ -843,7 +843,7 @@ static void qlcnic_dcb_get_pg_bwg_cfg_tx(struct net_device *netdev, int pgid, !type->tc_param_valid) return; - if (pgid < 0 || pgid > QLC_DCB_MAX_PG) + if (pgid < 0 || pgid >= QLC_DCB_MAX_PG) return; pgcfg = &type->pg_cfg[pgid]; -- cgit v1.2.1 From c502224efb2eaec47f16da39235079598a0f3ed2 Mon Sep 17 00:00:00 2001 From: Somnath Kotur Date: Mon, 3 Mar 2014 14:24:20 +0530 Subject: be2net: Fix to reset transparent vlan tagging For disabling transparent tagging issue SET_HSW_CONFIG with pvid_valid=1 and pvid=0xFFFF and not with the default pvid as this case would fail in Lancer. Hence removing the get_hsw_config call from be_vf_setup() as it's only use of getting default pvid is no longer needed. Also do proper housekeeping only if the FW command succeeds. Signed-off-by: Kalesh AP Signed-off-by: Somnath Kotur Signed-off-by: David S. Miller --- drivers/net/ethernet/emulex/benet/be.h | 4 +++- drivers/net/ethernet/emulex/benet/be_main.c | 28 +++++++++------------------- 2 files changed, 12 insertions(+), 20 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/emulex/benet/be.h b/drivers/net/ethernet/emulex/benet/be.h index 8d09615da585..05529e273050 100644 --- a/drivers/net/ethernet/emulex/benet/be.h +++ b/drivers/net/ethernet/emulex/benet/be.h @@ -350,11 +350,13 @@ struct be_drv_stats { u32 roce_drops_crc; }; +/* A vlan-id of 0xFFFF must be used to clear transparent vlan-tagging */ +#define BE_RESET_VLAN_TAG_ID 0xFFFF + struct be_vf_cfg { unsigned char mac_addr[ETH_ALEN]; int if_handle; int pmac_id; - u16 def_vid; u16 vlan_tag; u32 tx_rate; }; diff --git a/drivers/net/ethernet/emulex/benet/be_main.c b/drivers/net/ethernet/emulex/benet/be_main.c index 04ac9c6a0d39..45662af28928 100644 --- a/drivers/net/ethernet/emulex/benet/be_main.c +++ b/drivers/net/ethernet/emulex/benet/be_main.c @@ -1287,24 +1287,20 @@ static int be_set_vf_vlan(struct net_device *netdev, if (vlan || qos) { vlan |= qos << VLAN_PRIO_SHIFT; - if (vf_cfg->vlan_tag != vlan) { - /* If this is new value, program it. Else skip. */ - vf_cfg->vlan_tag = vlan; + if (vf_cfg->vlan_tag != vlan) status = be_cmd_set_hsw_config(adapter, vlan, vf + 1, vf_cfg->if_handle, 0); - } } else { /* Reset Transparent Vlan Tagging. */ - vf_cfg->vlan_tag = 0; - vlan = vf_cfg->def_vid; - status = be_cmd_set_hsw_config(adapter, vlan, vf + 1, - vf_cfg->if_handle, 0); + status = be_cmd_set_hsw_config(adapter, BE_RESET_VLAN_TAG_ID, + vf + 1, vf_cfg->if_handle, 0); } - - if (status) + if (!status) + vf_cfg->vlan_tag = vlan; + else dev_info(&adapter->pdev->dev, - "VLAN %d config on VF %d failed\n", vlan, vf); + "VLAN %d config on VF %d failed\n", vlan, vf); return status; } @@ -3013,11 +3009,11 @@ static int be_vf_setup_init(struct be_adapter *adapter) static int be_vf_setup(struct be_adapter *adapter) { + struct device *dev = &adapter->pdev->dev; struct be_vf_cfg *vf_cfg; - u16 def_vlan, lnk_speed; int status, old_vfs, vf; - struct device *dev = &adapter->pdev->dev; u32 privileges; + u16 lnk_speed; old_vfs = pci_num_vf(adapter->pdev); if (old_vfs) { @@ -3084,12 +3080,6 @@ static int be_vf_setup(struct be_adapter *adapter) if (!status) vf_cfg->tx_rate = lnk_speed; - status = be_cmd_get_hsw_config(adapter, &def_vlan, - vf + 1, vf_cfg->if_handle, NULL); - if (status) - goto err; - vf_cfg->def_vid = def_vlan; - if (!old_vfs) be_cmd_enable_vf(adapter, vf + 1); } -- cgit v1.2.1 From 7ad09458a5be9a0990457c1a198e702559ac25ca Mon Sep 17 00:00:00 2001 From: Somnath kotur Date: Mon, 3 Mar 2014 14:24:43 +0530 Subject: be2net: clear promiscuous bits in adapter->flags while disabling promiscuous mode We should clear promiscuous bits in adapter->flags while disabling promiscuous mode. Else we will not put interface back into VLAN promisc mode if the vlans already added exceeds the maximum limit. Signed-off-by: Kalesh AP Signed-off-by: Somnath Kotur Signed-off-by: David S. Miller --- drivers/net/ethernet/emulex/benet/be_main.c | 12 +++++++++--- 1 file changed, 9 insertions(+), 3 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/emulex/benet/be_main.c b/drivers/net/ethernet/emulex/benet/be_main.c index 45662af28928..9e6d678bca43 100644 --- a/drivers/net/ethernet/emulex/benet/be_main.c +++ b/drivers/net/ethernet/emulex/benet/be_main.c @@ -1157,6 +1157,14 @@ ret: return status; } +static void be_clear_promisc(struct be_adapter *adapter) +{ + adapter->promiscuous = false; + adapter->flags &= ~BE_FLAGS_VLAN_PROMISC; + + be_cmd_rx_filter(adapter, IFF_PROMISC, OFF); +} + static void be_set_rx_mode(struct net_device *netdev) { struct be_adapter *adapter = netdev_priv(netdev); @@ -1170,9 +1178,7 @@ static void be_set_rx_mode(struct net_device *netdev) /* BE was previously in promiscuous mode; disable it */ if (adapter->promiscuous) { - adapter->promiscuous = false; - be_cmd_rx_filter(adapter, IFF_PROMISC, OFF); - + be_clear_promisc(adapter); if (adapter->vlans_added) be_vid_config(adapter); } -- cgit v1.2.1 From c91289510602baf9a05b3501d97dc70efa269e01 Mon Sep 17 00:00:00 2001 From: Vasundhara Volam Date: Mon, 3 Mar 2014 14:25:07 +0530 Subject: be2net: Fix skb double free in be_xmit_wrokarounds() failure path skb_padto(), skb_share_check() and __vlan_put_tag() routines free skb when they return an error. This patch fixes be_xmit_workarounds() to not free skb again in such cases. Signed-off-by: Vasundhara Volam Signed-off-by: Sathya Perla Signed-off-by: Somnath Kotur Signed-off-by: David S. Miller --- drivers/net/ethernet/emulex/benet/be_main.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/emulex/benet/be_main.c b/drivers/net/ethernet/emulex/benet/be_main.c index 9e6d678bca43..a9da6f94e2fd 100644 --- a/drivers/net/ethernet/emulex/benet/be_main.c +++ b/drivers/net/ethernet/emulex/benet/be_main.c @@ -927,7 +927,7 @@ static struct sk_buff *be_xmit_workarounds(struct be_adapter *adapter, */ if (unlikely(!BEx_chip(adapter) && skb->len <= 32)) { if (skb_padto(skb, 36)) - goto tx_drop; + goto err; skb->len = 36; } @@ -959,7 +959,7 @@ static struct sk_buff *be_xmit_workarounds(struct be_adapter *adapter, vlan_tx_tag_present(skb)) { skb = be_insert_vlan_in_pkt(adapter, skb, skip_hw_vlan); if (unlikely(!skb)) - goto tx_drop; + goto err; } /* HW may lockup when VLAN HW tagging is requested on @@ -981,12 +981,13 @@ static struct sk_buff *be_xmit_workarounds(struct be_adapter *adapter, be_vlan_tag_tx_chk(adapter, skb)) { skb = be_insert_vlan_in_pkt(adapter, skb, skip_hw_vlan); if (unlikely(!skb)) - goto tx_drop; + goto err; } return skb; tx_drop: dev_kfree_skb_any(skb); +err: return NULL; } -- cgit v1.2.1 From ec495fac119f2eaea8b8c6e6db17ba163c7af1f4 Mon Sep 17 00:00:00 2001 From: Vasundhara Volam Date: Mon, 3 Mar 2014 14:25:38 +0530 Subject: be2net: isolate TX workarounds not applicable to Skyhawk-R Some of TX workarounds in be_xmit_workarounds() routine are not applicable (and result in HW errors) to Skyhawk-R chip. Isolate BE3-R/Lancer specific workarounds to a separate routine. Signed-off-by: Vasundhara Volam Signed-off-by: Sathya Perla Signed-off-by: Somnath Kotur Signed-off-by: David S. Miller --- drivers/net/ethernet/emulex/benet/be_main.c | 39 +++++++++++++++++++---------- 1 file changed, 26 insertions(+), 13 deletions(-) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/emulex/benet/be_main.c b/drivers/net/ethernet/emulex/benet/be_main.c index a9da6f94e2fd..36c80612e21a 100644 --- a/drivers/net/ethernet/emulex/benet/be_main.c +++ b/drivers/net/ethernet/emulex/benet/be_main.c @@ -913,24 +913,14 @@ static int be_ipv6_tx_stall_chk(struct be_adapter *adapter, return BE3_chip(adapter) && be_ipv6_exthdr_check(skb); } -static struct sk_buff *be_xmit_workarounds(struct be_adapter *adapter, - struct sk_buff *skb, - bool *skip_hw_vlan) +static struct sk_buff *be_lancer_xmit_workarounds(struct be_adapter *adapter, + struct sk_buff *skb, + bool *skip_hw_vlan) { struct vlan_ethhdr *veh = (struct vlan_ethhdr *)skb->data; unsigned int eth_hdr_len; struct iphdr *ip; - /* Lancer, SH-R ASICs have a bug wherein Packets that are 32 bytes or less - * may cause a transmit stall on that port. So the work-around is to - * pad short packets (<= 32 bytes) to a 36-byte length. - */ - if (unlikely(!BEx_chip(adapter) && skb->len <= 32)) { - if (skb_padto(skb, 36)) - goto err; - skb->len = 36; - } - /* For padded packets, BE HW modifies tot_len field in IP header * incorrecly when VLAN tag is inserted by HW. * For padded packets, Lancer computes incorrect checksum. @@ -991,6 +981,29 @@ err: return NULL; } +static struct sk_buff *be_xmit_workarounds(struct be_adapter *adapter, + struct sk_buff *skb, + bool *skip_hw_vlan) +{ + /* Lancer, SH-R ASICs have a bug wherein Packets that are 32 bytes or + * less may cause a transmit stall on that port. So the work-around is + * to pad short packets (<= 32 bytes) to a 36-byte length. + */ + if (unlikely(!BEx_chip(adapter) && skb->len <= 32)) { + if (skb_padto(skb, 36)) + return NULL; + skb->len = 36; + } + + if (BEx_chip(adapter) || lancer_chip(adapter)) { + skb = be_lancer_xmit_workarounds(adapter, skb, skip_hw_vlan); + if (!skb) + return NULL; + } + + return skb; +} + static netdev_tx_t be_xmit(struct sk_buff *skb, struct net_device *netdev) { struct be_adapter *adapter = netdev_priv(netdev); -- cgit v1.2.1 From 3995d265b3640fb7dc843a3c5f62ced4f121fb89 Mon Sep 17 00:00:00 2001 From: Schuyler Patton Date: Mon, 3 Mar 2014 16:19:06 +0530 Subject: net: cpsw: fix cpdma rx descriptor leak on down interface This patch fixes a CPDMA RX Descriptor leak that occurs after taking the interface down when the CPSW is in Dual MAC mode. Previously the CPSW_ALE port was left open up which causes packets to be received and processed by the RX interrupt handler and were passed to the non active network interface where they were ignored. The fix is for the slave_stop function of the selected interface to disable the respective CPSW_ALE Port from forwarding packets. This blocks traffic from being received on the inactive interface. Signed-off-by: Schuyler Patton Reviewed-by: Felipe Balbi Signed-off-by: Mugunthan V N Signed-off-by: David S. Miller --- drivers/net/ethernet/ti/cpsw.c | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'drivers/net/ethernet') diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c index 651087b5c8da..ffd4d12acf6d 100644 --- a/drivers/net/ethernet/ti/cpsw.c +++ b/drivers/net/ethernet/ti/cpsw.c @@ -1164,11 +1164,17 @@ static void cpsw_init_host_port(struct cpsw_priv *priv) static void cpsw_slave_stop(struct cpsw_slave *slave, struct cpsw_priv *priv) { + u32 slave_port; + + slave_port = cpsw_get_slave_port(priv, slave->slave_num); + if (!slave->phy) return; phy_stop(slave->phy); phy_disconnect(slave->phy); slave->phy = NULL; + cpsw_ale_control_set(priv->ale, slave_port, + ALE_PORT_STATE, ALE_PORT_STATE_DISABLE); } static int cpsw_ndo_open(struct net_device *ndev) -- cgit v1.2.1