From 669a5db411d85a14f86cd92bc16bf7ab5b8aa235 Mon Sep 17 00:00:00 2001 From: Jeff Garzik Date: Tue, 29 Aug 2006 18:12:40 -0400 Subject: [libata] Add a bunch of PATA drivers. The vast majority of drivers and changes are from Alan Cox. Albert Lee contributed and maintains pata_pdc2027x. Adrian Bunk, Andrew Morton, and Tejun Heo contributed various minor fixes and updates. Signed-off-by: Jeff Garzik --- drivers/ata/pata_hpt37x.c | 1257 +++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 1257 insertions(+) create mode 100644 drivers/ata/pata_hpt37x.c (limited to 'drivers/ata/pata_hpt37x.c') diff --git a/drivers/ata/pata_hpt37x.c b/drivers/ata/pata_hpt37x.c new file mode 100644 index 000000000000..7c3da53f1e0c --- /dev/null +++ b/drivers/ata/pata_hpt37x.c @@ -0,0 +1,1257 @@ +/* + * Libata driver for the highpoint 37x and 30x UDMA66 ATA controllers. + * + * This driver is heavily based upon: + * + * linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003 + * + * Copyright (C) 1999-2003 Andre Hedrick + * Portions Copyright (C) 2001 Sun Microsystems, Inc. + * Portions Copyright (C) 2003 Red Hat Inc + * + * TODO + * PLL mode + * Look into engine reset on timeout errors. Should not be + * required. + */ + +#include +#include +#include +#include +#include +#include +#include +#include + +#define DRV_NAME "pata_hpt37x" +#define DRV_VERSION "0.5" + +struct hpt_clock { + u8 xfer_speed; + u32 timing; +}; + +struct hpt_chip { + const char *name; + unsigned int base; + struct hpt_clock const *clocks[4]; +}; + +/* key for bus clock timings + * bit + * 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW + * DMA. cycles = value + 1 + * 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW + * DMA. cycles = value + 1 + * 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file + * register access. + * 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file + * register access. + * 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer. + * during task file register access. + * 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA + * xfer. + * 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task + * register access. + * 28 UDMA enable + * 29 DMA enable + * 30 PIO_MST enable. if set, the chip is in bus master mode during + * PIO. + * 31 FIFO enable. + */ + +/* from highpoint documentation. these are old values */ +static const struct hpt_clock hpt370_timings_33[] = { +/* { XFER_UDMA_5, 0x1A85F442, 0x16454e31 }, */ + { XFER_UDMA_5, 0x16454e31 }, + { XFER_UDMA_4, 0x16454e31 }, + { XFER_UDMA_3, 0x166d4e31 }, + { XFER_UDMA_2, 0x16494e31 }, + { XFER_UDMA_1, 0x164d4e31 }, + { XFER_UDMA_0, 0x16514e31 }, + + { XFER_MW_DMA_2, 0x26514e21 }, + { XFER_MW_DMA_1, 0x26514e33 }, + { XFER_MW_DMA_0, 0x26514e97 }, + + { XFER_PIO_4, 0x06514e21 }, + { XFER_PIO_3, 0x06514e22 }, + { XFER_PIO_2, 0x06514e33 }, + { XFER_PIO_1, 0x06914e43 }, + { XFER_PIO_0, 0x06914e57 }, + { 0, 0x06514e57 } +}; + +static const struct hpt_clock hpt370_timings_66[] = { + { XFER_UDMA_5, 0x14846231 }, + { XFER_UDMA_4, 0x14886231 }, + { XFER_UDMA_3, 0x148c6231 }, + { XFER_UDMA_2, 0x148c6231 }, + { XFER_UDMA_1, 0x14906231 }, + { XFER_UDMA_0, 0x14986231 }, + + { XFER_MW_DMA_2, 0x26514e21 }, + { XFER_MW_DMA_1, 0x26514e33 }, + { XFER_MW_DMA_0, 0x26514e97 }, + + { XFER_PIO_4, 0x06514e21 }, + { XFER_PIO_3, 0x06514e22 }, + { XFER_PIO_2, 0x06514e33 }, + { XFER_PIO_1, 0x06914e43 }, + { XFER_PIO_0, 0x06914e57 }, + { 0, 0x06514e57 } +}; + +/* these are the current (4 sep 2001) timings from highpoint */ +static const struct hpt_clock hpt370a_timings_33[] = { + { XFER_UDMA_5, 0x12446231 }, + { XFER_UDMA_4, 0x12446231 }, + { XFER_UDMA_3, 0x126c6231 }, + { XFER_UDMA_2, 0x12486231 }, + { XFER_UDMA_1, 0x124c6233 }, + { XFER_UDMA_0, 0x12506297 }, + + { XFER_MW_DMA_2, 0x22406c31 }, + { XFER_MW_DMA_1, 0x22406c33 }, + { XFER_MW_DMA_0, 0x22406c97 }, + + { XFER_PIO_4, 0x06414e31 }, + { XFER_PIO_3, 0x06414e42 }, + { XFER_PIO_2, 0x06414e53 }, + { XFER_PIO_1, 0x06814e93 }, + { XFER_PIO_0, 0x06814ea7 }, + { 0, 0x06814ea7 } +}; + +/* 2x 33MHz timings */ +static const struct hpt_clock hpt370a_timings_66[] = { + { XFER_UDMA_5, 0x1488e673 }, + { XFER_UDMA_4, 0x1488e673 }, + { XFER_UDMA_3, 0x1498e673 }, + { XFER_UDMA_2, 0x1490e673 }, + { XFER_UDMA_1, 0x1498e677 }, + { XFER_UDMA_0, 0x14a0e73f }, + + { XFER_MW_DMA_2, 0x2480fa73 }, + { XFER_MW_DMA_1, 0x2480fa77 }, + { XFER_MW_DMA_0, 0x2480fb3f }, + + { XFER_PIO_4, 0x0c82be73 }, + { XFER_PIO_3, 0x0c82be95 }, + { XFER_PIO_2, 0x0c82beb7 }, + { XFER_PIO_1, 0x0d02bf37 }, + { XFER_PIO_0, 0x0d02bf5f }, + { 0, 0x0d02bf5f } +}; + +static const struct hpt_clock hpt370a_timings_50[] = { + { XFER_UDMA_5, 0x12848242 }, + { XFER_UDMA_4, 0x12ac8242 }, + { XFER_UDMA_3, 0x128c8242 }, + { XFER_UDMA_2, 0x120c8242 }, + { XFER_UDMA_1, 0x12148254 }, + { XFER_UDMA_0, 0x121882ea }, + + { XFER_MW_DMA_2, 0x22808242 }, + { XFER_MW_DMA_1, 0x22808254 }, + { XFER_MW_DMA_0, 0x228082ea }, + + { XFER_PIO_4, 0x0a81f442 }, + { XFER_PIO_3, 0x0a81f443 }, + { XFER_PIO_2, 0x0a81f454 }, + { XFER_PIO_1, 0x0ac1f465 }, + { XFER_PIO_0, 0x0ac1f48a }, + { 0, 0x0ac1f48a } +}; + +static const struct hpt_clock hpt372_timings_33[] = { + { XFER_UDMA_6, 0x1c81dc62 }, + { XFER_UDMA_5, 0x1c6ddc62 }, + { XFER_UDMA_4, 0x1c8ddc62 }, + { XFER_UDMA_3, 0x1c8edc62 }, /* checkme */ + { XFER_UDMA_2, 0x1c91dc62 }, + { XFER_UDMA_1, 0x1c9adc62 }, /* checkme */ + { XFER_UDMA_0, 0x1c82dc62 }, /* checkme */ + + { XFER_MW_DMA_2, 0x2c829262 }, + { XFER_MW_DMA_1, 0x2c829266 }, /* checkme */ + { XFER_MW_DMA_0, 0x2c82922e }, /* checkme */ + + { XFER_PIO_4, 0x0c829c62 }, + { XFER_PIO_3, 0x0c829c84 }, + { XFER_PIO_2, 0x0c829ca6 }, + { XFER_PIO_1, 0x0d029d26 }, + { XFER_PIO_0, 0x0d029d5e }, + { 0, 0x0d029d5e } +}; + +static const struct hpt_clock hpt372_timings_50[] = { + { XFER_UDMA_5, 0x12848242 }, + { XFER_UDMA_4, 0x12ac8242 }, + { XFER_UDMA_3, 0x128c8242 }, + { XFER_UDMA_2, 0x120c8242 }, + { XFER_UDMA_1, 0x12148254 }, + { XFER_UDMA_0, 0x121882ea }, + + { XFER_MW_DMA_2, 0x22808242 }, + { XFER_MW_DMA_1, 0x22808254 }, + { XFER_MW_DMA_0, 0x228082ea }, + + { XFER_PIO_4, 0x0a81f442 }, + { XFER_PIO_3, 0x0a81f443 }, + { XFER_PIO_2, 0x0a81f454 }, + { XFER_PIO_1, 0x0ac1f465 }, + { XFER_PIO_0, 0x0ac1f48a }, + { 0, 0x0a81f443 } +}; + +static const struct hpt_clock hpt372_timings_66[] = { + { XFER_UDMA_6, 0x1c869c62 }, + { XFER_UDMA_5, 0x1cae9c62 }, + { XFER_UDMA_4, 0x1c8a9c62 }, + { XFER_UDMA_3, 0x1c8e9c62 }, + { XFER_UDMA_2, 0x1c929c62 }, + { XFER_UDMA_1, 0x1c9a9c62 }, + { XFER_UDMA_0, 0x1c829c62 }, + + { XFER_MW_DMA_2, 0x2c829c62 }, + { XFER_MW_DMA_1, 0x2c829c66 }, + { XFER_MW_DMA_0, 0x2c829d2e }, + + { XFER_PIO_4, 0x0c829c62 }, + { XFER_PIO_3, 0x0c829c84 }, + { XFER_PIO_2, 0x0c829ca6 }, + { XFER_PIO_1, 0x0d029d26 }, + { XFER_PIO_0, 0x0d029d5e }, + { 0, 0x0d029d26 } +}; + +static const struct hpt_clock hpt374_timings_33[] = { + { XFER_UDMA_6, 0x12808242 }, + { XFER_UDMA_5, 0x12848242 }, + { XFER_UDMA_4, 0x12ac8242 }, + { XFER_UDMA_3, 0x128c8242 }, + { XFER_UDMA_2, 0x120c8242 }, + { XFER_UDMA_1, 0x12148254 }, + { XFER_UDMA_0, 0x121882ea }, + + { XFER_MW_DMA_2, 0x22808242 }, + { XFER_MW_DMA_1, 0x22808254 }, + { XFER_MW_DMA_0, 0x228082ea }, + + { XFER_PIO_4, 0x0a81f442 }, + { XFER_PIO_3, 0x0a81f443 }, + { XFER_PIO_2, 0x0a81f454 }, + { XFER_PIO_1, 0x0ac1f465 }, + { XFER_PIO_0, 0x0ac1f48a }, + { 0, 0x06814e93 } +}; + +static const struct hpt_chip hpt370 = { + "HPT370", + 48, + { + hpt370_timings_33, + NULL, + NULL, + hpt370_timings_66 + } +}; + +static const struct hpt_chip hpt370a = { + "HPT370A", + 48, + { + hpt370a_timings_33, + NULL, + hpt370a_timings_50, + hpt370a_timings_66 + } +}; + +static const struct hpt_chip hpt372 = { + "HPT372", + 55, + { + hpt372_timings_33, + NULL, + hpt372_timings_50, + hpt372_timings_66 + } +}; + +static const struct hpt_chip hpt302 = { + "HPT302", + 66, + { + hpt372_timings_33, + NULL, + hpt372_timings_50, + hpt372_timings_66 + } +}; + +static const struct hpt_chip hpt371 = { + "HPT371", + 66, + { + hpt372_timings_33, + NULL, + hpt372_timings_50, + hpt372_timings_66 + } +}; + +static const struct hpt_chip hpt372a = { + "HPT372A", + 66, + { + hpt372_timings_33, + NULL, + hpt372_timings_50, + hpt372_timings_66 + } +}; + +static const struct hpt_chip hpt374 = { + "HPT374", + 48, + { + hpt374_timings_33, + NULL, + NULL, + NULL + } +}; + +/** + * hpt37x_find_mode - reset the hpt37x bus + * @ap: ATA port + * @speed: transfer mode + * + * Return the 32bit register programming information for this channel + * that matches the speed provided. + */ + +static u32 hpt37x_find_mode(struct ata_port *ap, int speed) +{ + struct hpt_clock *clocks = ap->host->private_data; + + while(clocks->xfer_speed) { + if (clocks->xfer_speed == speed) + return clocks->timing; + clocks++; + } + BUG(); + return 0xffffffffU; /* silence compiler warning */ +} + +static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr, const char *list[]) +{ + unsigned char model_num[40]; + char *s; + unsigned int len; + int i = 0; + + ata_id_string(dev->id, model_num, ATA_ID_PROD_OFS, + sizeof(model_num)); + s = &model_num[0]; + len = strnlen(s, sizeof(model_num)); + + /* ATAPI specifies that empty space is blank-filled; remove blanks */ + while ((len > 0) && (s[len - 1] == ' ')) { + len--; + s[len] = 0; + } + + while(list[i] != NULL) { + if (!strncmp(list[i], s, len)) { + printk(KERN_WARNING DRV_NAME ": %s is not supported for %s.\n", + modestr, list[i]); + return 1; + } + i++; + } + return 0; +} + +static const char *bad_ata33[] = { + "Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", "Maxtor 90845U3", "Maxtor 90650U2", + "Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2", + "Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4", + "Maxtor 90510D4", + "Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2", + "Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4", + "Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2", + NULL +}; + +static const char *bad_ata100_5[] = { + "IBM-DTLA-307075", + "IBM-DTLA-307060", + "IBM-DTLA-307045", + "IBM-DTLA-307030", + "IBM-DTLA-307020", + "IBM-DTLA-307015", + "IBM-DTLA-305040", + "IBM-DTLA-305030", + "IBM-DTLA-305020", + "IC35L010AVER07-0", + "IC35L020AVER07-0", + "IC35L030AVER07-0", + "IC35L040AVER07-0", + "IC35L060AVER07-0", + "WDC AC310200R", + NULL +}; + +/** + * hpt370_filter - mode selection filter + * @ap: ATA interface + * @adev: ATA device + * + * Block UDMA on devices that cause trouble with this controller. + */ + +static unsigned long hpt370_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask) +{ + if (adev->class != ATA_DEV_ATA) { + if (hpt_dma_blacklisted(adev, "UDMA", bad_ata33)) + mask &= ~ATA_MASK_UDMA; + if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5)) + mask &= ~(0x1F << ATA_SHIFT_UDMA); + } + return ata_pci_default_filter(ap, adev, mask); +} + +/** + * hpt370a_filter - mode selection filter + * @ap: ATA interface + * @adev: ATA device + * + * Block UDMA on devices that cause trouble with this controller. + */ + +static unsigned long hpt370a_filter(const struct ata_port *ap, struct ata_device *adev, unsigned long mask) +{ + if (adev->class != ATA_DEV_ATA) { + if (hpt_dma_blacklisted(adev, "UDMA100", bad_ata100_5)) + mask &= ~ (0x1F << ATA_SHIFT_UDMA); + } + return ata_pci_default_filter(ap, adev, mask); +} + +/** + * hpt37x_pre_reset - reset the hpt37x bus + * @ap: ATA port to reset + * + * Perform the initial reset handling for the 370/372 and 374 func 0 + */ + +static int hpt37x_pre_reset(struct ata_port *ap) +{ + u8 scr2, ata66; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + pci_read_config_byte(pdev, 0x5B, &scr2); + pci_write_config_byte(pdev, 0x5B, scr2 & ~0x01); + /* Cable register now active */ + pci_read_config_byte(pdev, 0x5A, &ata66); + /* Restore state */ + pci_write_config_byte(pdev, 0x5B, scr2); + + if (ata66 & (1 << ap->port_no)) + ap->cbl = ATA_CBL_PATA40; + else + ap->cbl = ATA_CBL_PATA80; + + /* Reset the state machine */ + pci_write_config_byte(pdev, 0x50, 0x37); + pci_write_config_byte(pdev, 0x54, 0x37); + udelay(100); + + return ata_std_prereset(ap); +} + +/** + * hpt37x_error_handler - reset the hpt374 + * @ap: ATA port to reset + * + * Perform probe for HPT37x, except for HPT374 channel 2 + */ + +static void hpt37x_error_handler(struct ata_port *ap) +{ + ata_bmdma_drive_eh(ap, hpt37x_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +static int hpt374_pre_reset(struct ata_port *ap) +{ + u16 mcr3, mcr6; + u8 ata66; + + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + /* Do the extra channel work */ + pci_read_config_word(pdev, 0x52, &mcr3); + pci_read_config_word(pdev, 0x56, &mcr6); + /* Set bit 15 of 0x52 to enable TCBLID as input + Set bit 15 of 0x56 to enable FCBLID as input + */ + pci_write_config_word(pdev, 0x52, mcr3 | 0x8000); + pci_write_config_word(pdev, 0x56, mcr6 | 0x8000); + pci_read_config_byte(pdev, 0x5A, &ata66); + /* Reset TCBLID/FCBLID to output */ + pci_write_config_word(pdev, 0x52, mcr3); + pci_write_config_word(pdev, 0x56, mcr6); + + if (ata66 & (1 << ap->port_no)) + ap->cbl = ATA_CBL_PATA40; + else + ap->cbl = ATA_CBL_PATA80; + + /* Reset the state machine */ + pci_write_config_byte(pdev, 0x50, 0x37); + pci_write_config_byte(pdev, 0x54, 0x37); + udelay(100); + + return ata_std_prereset(ap); +} + +/** + * hpt374_error_handler - reset the hpt374 + * @classes: + * + * The 374 cable detect is a little different due to the extra + * channels. The function 0 channels work like usual but function 1 + * is special + */ + +static void hpt374_error_handler(struct ata_port *ap) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + + if (!(PCI_FUNC(pdev->devfn) & 1)) + hpt37x_error_handler(ap); + else + ata_bmdma_drive_eh(ap, hpt374_pre_reset, ata_std_softreset, NULL, ata_std_postreset); +} + +/** + * hpt370_set_piomode - PIO setup + * @ap: ATA interface + * @adev: device on the interface + * + * Perform PIO mode setup. + */ + +static void hpt370_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 addr1, addr2; + u32 reg; + u32 mode; + u8 fast; + + addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); + addr2 = 0x51 + 4 * ap->port_no; + + /* Fast interrupt prediction disable, hold off interrupt disable */ + pci_read_config_byte(pdev, addr2, &fast); + fast &= ~0x02; + fast |= 0x01; + pci_write_config_byte(pdev, addr2, fast); + + pci_read_config_dword(pdev, addr1, ®); + mode = hpt37x_find_mode(ap, adev->pio_mode); + mode &= ~0x8000000; /* No FIFO in PIO */ + mode &= ~0x30070000; /* Leave config bits alone */ + reg &= 0x30070000; /* Strip timing bits */ + pci_write_config_dword(pdev, addr1, reg | mode); +} + +/** + * hpt370_set_dmamode - DMA timing setup + * @ap: ATA interface + * @adev: Device being configured + * + * Set up the channel for MWDMA or UDMA modes. Much the same as with + * PIO, load the mode number and then set MWDMA or UDMA flag. + */ + +static void hpt370_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 addr1, addr2; + u32 reg; + u32 mode; + u8 fast; + + addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); + addr2 = 0x51 + 4 * ap->port_no; + + /* Fast interrupt prediction disable, hold off interrupt disable */ + pci_read_config_byte(pdev, addr2, &fast); + fast &= ~0x02; + fast |= 0x01; + pci_write_config_byte(pdev, addr2, fast); + + pci_read_config_dword(pdev, addr1, ®); + mode = hpt37x_find_mode(ap, adev->dma_mode); + mode |= 0x8000000; /* FIFO in MWDMA or UDMA */ + mode &= ~0xC0000000; /* Leave config bits alone */ + reg &= 0xC0000000; /* Strip timing bits */ + pci_write_config_dword(pdev, addr1, reg | mode); +} + +/** + * hpt370_bmdma_start - DMA engine begin + * @qc: ATA command + * + * The 370 and 370A want us to reset the DMA engine each time we + * use it. The 372 and later are fine. + */ + +static void hpt370_bmdma_start(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37); + udelay(10); + ata_bmdma_start(qc); +} + +/** + * hpt370_bmdma_end - DMA engine stop + * @qc: ATA command + * + * Work around the HPT370 DMA engine. + */ + +static void hpt370_bmdma_stop(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u8 dma_stat = inb(ap->ioaddr.bmdma_addr + 2); + u8 dma_cmd; + unsigned long bmdma = ap->ioaddr.bmdma_addr; + + if (dma_stat & 0x01) { + udelay(20); + dma_stat = inb(bmdma + 2); + } + if (dma_stat & 0x01) { + /* Clear the engine */ + pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37); + udelay(10); + /* Stop DMA */ + dma_cmd = inb(bmdma ); + outb(dma_cmd & 0xFE, bmdma); + /* Clear Error */ + dma_stat = inb(bmdma + 2); + outb(dma_stat | 0x06 , bmdma + 2); + /* Clear the engine */ + pci_write_config_byte(pdev, 0x50 + 4 * ap->port_no, 0x37); + udelay(10); + } + ata_bmdma_stop(qc); +} + +/** + * hpt372_set_piomode - PIO setup + * @ap: ATA interface + * @adev: device on the interface + * + * Perform PIO mode setup. + */ + +static void hpt372_set_piomode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 addr1, addr2; + u32 reg; + u32 mode; + u8 fast; + + addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); + addr2 = 0x51 + 4 * ap->port_no; + + /* Fast interrupt prediction disable, hold off interrupt disable */ + pci_read_config_byte(pdev, addr2, &fast); + fast &= ~0x07; + pci_write_config_byte(pdev, addr2, fast); + + pci_read_config_dword(pdev, addr1, ®); + mode = hpt37x_find_mode(ap, adev->pio_mode); + + printk("Find mode for %d reports %X\n", adev->pio_mode, mode); + mode &= ~0x80000000; /* No FIFO in PIO */ + mode &= ~0x30070000; /* Leave config bits alone */ + reg &= 0x30070000; /* Strip timing bits */ + pci_write_config_dword(pdev, addr1, reg | mode); +} + +/** + * hpt372_set_dmamode - DMA timing setup + * @ap: ATA interface + * @adev: Device being configured + * + * Set up the channel for MWDMA or UDMA modes. Much the same as with + * PIO, load the mode number and then set MWDMA or UDMA flag. + */ + +static void hpt372_set_dmamode(struct ata_port *ap, struct ata_device *adev) +{ + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + u32 addr1, addr2; + u32 reg; + u32 mode; + u8 fast; + + addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no); + addr2 = 0x51 + 4 * ap->port_no; + + /* Fast interrupt prediction disable, hold off interrupt disable */ + pci_read_config_byte(pdev, addr2, &fast); + fast &= ~0x07; + pci_write_config_byte(pdev, addr2, fast); + + pci_read_config_dword(pdev, addr1, ®); + mode = hpt37x_find_mode(ap, adev->dma_mode); + printk("Find mode for DMA %d reports %X\n", adev->dma_mode, mode); + mode &= ~0xC0000000; /* Leave config bits alone */ + mode |= 0x80000000; /* FIFO in MWDMA or UDMA */ + reg &= 0xC0000000; /* Strip timing bits */ + pci_write_config_dword(pdev, addr1, reg | mode); +} + +/** + * hpt37x_bmdma_end - DMA engine stop + * @qc: ATA command + * + * Clean up after the HPT372 and later DMA engine + */ + +static void hpt37x_bmdma_stop(struct ata_queued_cmd *qc) +{ + struct ata_port *ap = qc->ap; + struct pci_dev *pdev = to_pci_dev(ap->host->dev); + int mscreg = 0x50 + 2 * ap->port_no; + u8 bwsr_stat, msc_stat; + + pci_read_config_byte(pdev, 0x6A, &bwsr_stat); + pci_read_config_byte(pdev, mscreg, &msc_stat); + if (bwsr_stat & (1 << ap->port_no)) + pci_write_config_byte(pdev, mscreg, msc_stat | 0x30); + ata_bmdma_stop(qc); +} + + +static struct scsi_host_template hpt37x_sht = { + .module = THIS_MODULE, + .name = DRV_NAME, + .ioctl = ata_scsi_ioctl, + .queuecommand = ata_scsi_queuecmd, + .can_queue = ATA_DEF_QUEUE, + .this_id = ATA_SHT_THIS_ID, + .sg_tablesize = LIBATA_MAX_PRD, + .max_sectors = ATA_MAX_SECTORS, + .cmd_per_lun = ATA_SHT_CMD_PER_LUN, + .emulated = ATA_SHT_EMULATED, + .use_clustering = ATA_SHT_USE_CLUSTERING, + .proc_name = DRV_NAME, + .dma_boundary = ATA_DMA_BOUNDARY, + .slave_configure = ata_scsi_slave_config, + .bios_param = ata_std_bios_param, +}; + +/* + * Configuration for HPT370 + */ + +static struct ata_port_operations hpt370_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = hpt370_set_piomode, + .set_dmamode = hpt370_set_dmamode, + .mode_filter = hpt370_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = hpt37x_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = hpt370_bmdma_start, + .bmdma_stop = hpt370_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .eng_timeout = ata_eng_timeout, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/* + * Configuration for HPT370A. Close to 370 but less filters + */ + +static struct ata_port_operations hpt370a_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = hpt370_set_piomode, + .set_dmamode = hpt370_set_dmamode, + .mode_filter = hpt370a_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = hpt37x_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = hpt370_bmdma_start, + .bmdma_stop = hpt370_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .eng_timeout = ata_eng_timeout, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/* + * Configuration for HPT372, HPT371, HPT302. Slightly different PIO + * and DMA mode setting functionality. + */ + +static struct ata_port_operations hpt372_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = hpt372_set_piomode, + .set_dmamode = hpt372_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = hpt37x_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = hpt37x_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .eng_timeout = ata_eng_timeout, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/* + * Configuration for HPT374. Mode setting works like 372 and friends + * but we have a different cable detection procedure. + */ + +static struct ata_port_operations hpt374_port_ops = { + .port_disable = ata_port_disable, + .set_piomode = hpt372_set_piomode, + .set_dmamode = hpt372_set_dmamode, + .mode_filter = ata_pci_default_filter, + + .tf_load = ata_tf_load, + .tf_read = ata_tf_read, + .check_status = ata_check_status, + .exec_command = ata_exec_command, + .dev_select = ata_std_dev_select, + + .freeze = ata_bmdma_freeze, + .thaw = ata_bmdma_thaw, + .error_handler = hpt374_error_handler, + .post_internal_cmd = ata_bmdma_post_internal_cmd, + + .bmdma_setup = ata_bmdma_setup, + .bmdma_start = ata_bmdma_start, + .bmdma_stop = hpt37x_bmdma_stop, + .bmdma_status = ata_bmdma_status, + + .qc_prep = ata_qc_prep, + .qc_issue = ata_qc_issue_prot, + .eng_timeout = ata_eng_timeout, + .data_xfer = ata_pio_data_xfer, + + .irq_handler = ata_interrupt, + .irq_clear = ata_bmdma_irq_clear, + + .port_start = ata_port_start, + .port_stop = ata_port_stop, + .host_stop = ata_host_stop +}; + +/** + * htp37x_clock_slot - Turn timing to PC clock entry + * @freq: Reported frequency timing + * @base: Base timing + * + * Turn the timing data intoa clock slot (0 for 33, 1 for 40, 2 for 50 + * and 3 for 66Mhz) + */ + +static int hpt37x_clock_slot(unsigned int freq, unsigned int base) +{ + unsigned int f = (base * freq) / 192; /* Mhz */ + if (f < 40) + return 0; /* 33Mhz slot */ + if (f < 45) + return 1; /* 40Mhz slot */ + if (f < 55) + return 2; /* 50Mhz slot */ + return 3; /* 60Mhz slot */ +} + +/** + * hpt37x_calibrate_dpll - Calibrate the DPLL loop + * @dev: PCI device + * + * Perform a calibration cycle on the HPT37x DPLL. Returns 1 if this + * succeeds + */ + +static int hpt37x_calibrate_dpll(struct pci_dev *dev) +{ + u8 reg5b; + u32 reg5c; + int tries; + + for(tries = 0; tries < 0x5000; tries++) { + udelay(50); + pci_read_config_byte(dev, 0x5b, ®5b); + if (reg5b & 0x80) { + /* See if it stays set */ + for(tries = 0; tries < 0x1000; tries ++) { + pci_read_config_byte(dev, 0x5b, ®5b); + /* Failed ? */ + if ((reg5b & 0x80) == 0) + return 0; + } + /* Turn off tuning, we have the DPLL set */ + pci_read_config_dword(dev, 0x5c, ®5c); + pci_write_config_dword(dev, 0x5c, reg5c & ~ 0x100); + return 1; + } + } + /* Never went stable */ + return 0; +} +/** + * hpt37x_init_one - Initialise an HPT37X/302 + * @dev: PCI device + * @id: Entry in match table + * + * Initialise an HPT37x device. There are some interesting complications + * here. Firstly the chip may report 366 and be one of several variants. + * Secondly all the timings depend on the clock for the chip which we must + * detect and look up + * + * This is the known chip mappings. It may be missing a couple of later + * releases. + * + * Chip version PCI Rev Notes + * HPT366 4 (HPT366) 0 Other driver + * HPT366 4 (HPT366) 1 Other driver + * HPT368 4 (HPT366) 2 Other driver + * HPT370 4 (HPT366) 3 UDMA100 + * HPT370A 4 (HPT366) 4 UDMA100 + * HPT372 4 (HPT366) 5 UDMA133 (1) + * HPT372N 4 (HPT366) 6 Other driver + * HPT372A 5 (HPT372) 1 UDMA133 (1) + * HPT372N 5 (HPT372) 2 Other driver + * HPT302 6 (HPT302) 1 UDMA133 + * HPT302N 6 (HPT302) 2 Other driver + * HPT371 7 (HPT371) * UDMA133 + * HPT374 8 (HPT374) * UDMA133 4 channel + * HPT372N 9 (HPT372N) * Other driver + * + * (1) UDMA133 support depends on the bus clock + */ + +static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id) +{ + /* HPT370 - UDMA100 */ + static struct ata_port_info info_hpt370 = { + .sht = &hpt37x_sht, + .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x3f, + .port_ops = &hpt370_port_ops + }; + /* HPT370A - UDMA100 */ + static struct ata_port_info info_hpt370a = { + .sht = &hpt37x_sht, + .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x3f, + .port_ops = &hpt370a_port_ops + }; + /* HPT371, 372 and friends - UDMA133 */ + static struct ata_port_info info_hpt372 = { + .sht = &hpt37x_sht, + .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x7f, + .port_ops = &hpt372_port_ops + }; + /* HPT371, 372 and friends - UDMA100 at 50MHz clock */ + static struct ata_port_info info_hpt372_50 = { + .sht = &hpt37x_sht, + .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x3f, + .port_ops = &hpt372_port_ops + }; + /* HPT374 - UDMA133 */ + static struct ata_port_info info_hpt374 = { + .sht = &hpt37x_sht, + .flags = ATA_FLAG_SLAVE_POSS|ATA_FLAG_SRST, + .pio_mask = 0x1f, + .mwdma_mask = 0x07, + .udma_mask = 0x7f, + .port_ops = &hpt374_port_ops + }; + + static const int MHz[4] = { 33, 40, 50, 66 }; + + struct ata_port_info *port_info[2]; + struct ata_port_info *port; + + u8 irqmask; + u32 class_rev; + u32 freq; + + const struct hpt_chip *chip_table; + int clock_slot; + + pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev); + class_rev &= 0xFF; + + if (dev->device == PCI_DEVICE_ID_TTI_HPT366) { + /* May be a later chip in disguise. Check */ + /* Older chips are in the HPT366 driver. Ignore them */ + if (class_rev < 3) + return -ENODEV; + /* N series chips have their own driver. Ignore */ + if (class_rev == 6) + return -ENODEV; + + switch(class_rev) { + case 3: + port = &info_hpt370; + chip_table = &hpt370; + break; + case 4: + port = &info_hpt370a; + chip_table = &hpt370a; + break; + case 5: + port = &info_hpt372; + chip_table = &hpt372; + break; + default: + printk(KERN_ERR "pata_hpt37x: Unknown HPT366 subtype please report (%d).\n", class_rev); + return -ENODEV; + } + } else { + switch(dev->device) { + case PCI_DEVICE_ID_TTI_HPT372: + /* 372N if rev >= 2*/ + if (class_rev >= 2) + return -ENODEV; + port = &info_hpt372; + chip_table = &hpt372a; + break; + case PCI_DEVICE_ID_TTI_HPT302: + /* 302N if rev > 1 */ + if (class_rev > 1) + return -ENODEV; + port = &info_hpt372; + /* Check this */ + chip_table = &hpt302; + break; + case PCI_DEVICE_ID_TTI_HPT371: + port = &info_hpt372; + chip_table = &hpt371; + break; + case PCI_DEVICE_ID_TTI_HPT374: + chip_table = &hpt374; + port = &info_hpt374; + break; + default: + printk(KERN_ERR "pata_hpt37x: PCI table is bogus please report (%d).\n", dev->device); + return -ENODEV; + } + } + /* Ok so this is a chip we support */ + + pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4)); + pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78); + pci_write_config_byte(dev, PCI_MIN_GNT, 0x08); + pci_write_config_byte(dev, PCI_MAX_LAT, 0x08); + + pci_read_config_byte(dev, 0x5A, &irqmask); + irqmask &= ~0x10; + pci_write_config_byte(dev, 0x5a, irqmask); + + /* + * default to pci clock. make sure MA15/16 are set to output + * to prevent drives having problems with 40-pin cables. Needed + * for some drives such as IBM-DTLA which will not enter ready + * state on reset when PDIAG is a input. + */ + + pci_write_config_byte(dev, 0x5b, 0x23); + + pci_read_config_dword(dev, 0x70, &freq); + if ((freq >> 12) != 0xABCDE) { + int i; + u8 sr; + u32 total = 0; + + printk(KERN_WARNING "pata_hpt37x: BIOS has not set timing clocks.\n"); + + /* This is the process the HPT371 BIOS is reported to use */ + for(i = 0; i < 128; i++) { + pci_read_config_byte(dev, 0x78, &sr); + total += sr; + udelay(15); + } + freq = total / 128; + } + freq &= 0x1FF; + + /* + * Turn the frequency check into a band and then find a timing + * table to match it. + */ + + clock_slot = hpt37x_clock_slot(freq, chip_table->base); + if (chip_table->clocks[clock_slot] == NULL) { + /* + * We need to try PLL mode instead + */ + unsigned int f_low = (MHz[clock_slot] * chip_table->base) / 192; + unsigned int f_high = f_low + 2; + int adjust; + + for(adjust = 0; adjust < 8; adjust++) { + if (hpt37x_calibrate_dpll(dev)) + break; + /* See if it'll settle at a fractionally different clock */ + if ((adjust & 3) == 3) { + f_low --; + f_high ++; + } + pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low); + } + if (adjust == 8) { + printk(KERN_WARNING "hpt37x: DPLL did not stabilize.\n"); + return -ENODEV; + } + /* Check if this works for all cases */ + port->private_data = (void *)hpt370_timings_66; + + printk(KERN_INFO "hpt37x: Bus clock %dMHz, using DPLL.\n", MHz[clock_slot]); + } else { + port->private_data = (void *)chip_table->clocks[clock_slot]; + /* + * Perform a final fixup. The 371 and 372 clock determines + * if UDMA133 is available. + */ + + if (clock_slot == 2 && chip_table == &hpt372) { /* 50Mhz */ + printk(KERN_WARNING "pata_hpt37x: No UDMA133 support available with 50MHz bus clock.\n"); + if (port == &info_hpt372) + port = &info_hpt372_50; + else BUG(); + } + printk(KERN_INFO "hpt37x: %s: Bus clock %dMHz.\n", chip_table->name, MHz[clock_slot]); + } + port_info[0] = port_info[1] = port; + /* Now kick off ATA set up */ + return ata_pci_init_one(dev, port_info, 2); +} + +static struct pci_device_id hpt37x[] = { + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT366), }, + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT371), }, + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT372), }, + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT374), }, + { PCI_DEVICE(PCI_VENDOR_ID_TTI, PCI_DEVICE_ID_TTI_HPT302), }, + { 0, }, +}; + +static struct pci_driver hpt37x_pci_driver = { + .name = DRV_NAME, + .id_table = hpt37x, + .probe = hpt37x_init_one, + .remove = ata_pci_remove_one +}; + +static int __init hpt37x_init(void) +{ + return pci_register_driver(&hpt37x_pci_driver); +} + + +static void __exit hpt37x_exit(void) +{ + pci_unregister_driver(&hpt37x_pci_driver); +} + + +MODULE_AUTHOR("Alan Cox"); +MODULE_DESCRIPTION("low-level driver for the Highpoint HPT37x/30x"); +MODULE_LICENSE("GPL"); +MODULE_DEVICE_TABLE(pci, hpt37x); +MODULE_VERSION(DRV_VERSION); + +module_init(hpt37x_init); +module_exit(hpt37x_exit); -- cgit v1.2.1