From e2efc09e52680cecb0ca624e379cb4b4c56157c3 Mon Sep 17 00:00:00 2001 From: Tirumala Marri Date: Mon, 21 Dec 2009 22:49:41 +0000 Subject: powerpc/44x: Adding PCI-E support for PowerPC 460SX based SOC. Add support for PCI-e on the AMCC 460SX boards Signed-off-by: Tirumala Marri Acked-by: Josh Boyer --- arch/powerpc/boot/dts/redwood.dts | 122 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 122 insertions(+) (limited to 'arch/powerpc/boot/dts') diff --git a/arch/powerpc/boot/dts/redwood.dts b/arch/powerpc/boot/dts/redwood.dts index d2af32e2bf7a..81636c01d906 100644 --- a/arch/powerpc/boot/dts/redwood.dts +++ b/arch/powerpc/boot/dts/redwood.dts @@ -234,10 +234,132 @@ has-inverted-stacr-oc; has-new-stacr-staopc; }; + }; + PCIE0: pciex@d00000000 { + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "ibm,plb-pciex-460sx", "ibm,plb-pciex"; + primary; + port = <0x0>; /* port number */ + reg = <0x0000000d 0x00000000 0x20000000 /* Config space access */ + 0x0000000c 0x10000000 0x00001000>; /* Registers */ + dcr-reg = <0x100 0x020>; + sdr-base = <0x300>; + + /* Outbound ranges, one memory and one IO, + * later cannot be changed + */ + ranges = <0x02000000 0x00000000 0x80000000 0x0000000e 0x00000000 0x00000000 0x80000000 + 0x01000000 0x00000000 0x00000000 0x0000000f 0x80000000 0x00000000 0x00010000>; + + /* Inbound 2GB range starting at 0 */ + dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x80000000>; + /* This drives busses 10 to 0x1f */ + bus-range = <0x10 0x1f>; + + /* Legacy interrupts (note the weird polarity, the bridge seems + * to invert PCIe legacy interrupts). + * We are de-swizzling here because the numbers are actually for + * port of the root complex virtual P2P bridge. But I want + * to avoid putting a node for it in the tree, so the numbers + * below are basically de-swizzled numbers. + * The real slot is on idsel 0, so the swizzling is 1:1 + */ + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = < + 0x0 0x0 0x0 0x1 &UIC3 0x0 0x4 /* swizzled int A */ + 0x0 0x0 0x0 0x2 &UIC3 0x1 0x4 /* swizzled int B */ + 0x0 0x0 0x0 0x3 &UIC3 0x2 0x4 /* swizzled int C */ + 0x0 0x0 0x0 0x4 &UIC3 0x3 0x4 /* swizzled int D */>; + }; + + PCIE1: pciex@d20000000 { + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "ibm,plb-pciex-460sx", "ibm,plb-pciex"; + primary; + port = <0x1>; /* port number */ + reg = <0x0000000d 0x20000000 0x20000000 /* Config space access */ + 0x0000000c 0x10001000 0x00001000>; /* Registers */ + dcr-reg = <0x120 0x020>; + sdr-base = <0x340>; + + /* Outbound ranges, one memory and one IO, + * later cannot be changed + */ + ranges = <0x02000000 0x00000000 0x80000000 0x0000000e 0x80000000 0x00000000 0x80000000 + 0x01000000 0x00000000 0x00000000 0x0000000f 0x80010000 0x00000000 0x00010000>; + + /* Inbound 2GB range starting at 0 */ + dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x80000000>; + + /* This drives busses 10 to 0x1f */ + bus-range = <0x20 0x2f>; + + /* Legacy interrupts (note the weird polarity, the bridge seems + * to invert PCIe legacy interrupts). + * We are de-swizzling here because the numbers are actually for + * port of the root complex virtual P2P bridge. But I want + * to avoid putting a node for it in the tree, so the numbers + * below are basically de-swizzled numbers. + * The real slot is on idsel 0, so the swizzling is 1:1 + */ + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = < + 0x0 0x0 0x0 0x1 &UIC3 0x4 0x4 /* swizzled int A */ + 0x0 0x0 0x0 0x2 &UIC3 0x5 0x4 /* swizzled int B */ + 0x0 0x0 0x0 0x3 &UIC3 0x6 0x4 /* swizzled int C */ + 0x0 0x0 0x0 0x4 &UIC3 0x7 0x4 /* swizzled int D */>; + }; + + PCIE2: pciex@d40000000 { + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "ibm,plb-pciex-460sx", "ibm,plb-pciex"; + primary; + port = <0x2>; /* port number */ + reg = <0x0000000d 0x40000000 0x20000000 /* Config space access */ + 0x0000000c 0x10002000 0x00001000>; /* Registers */ + dcr-reg = <0x140 0x020>; + sdr-base = <0x370>; + + /* Outbound ranges, one memory and one IO, + * later cannot be changed + */ + ranges = <0x02000000 0x00000000 0x80000000 0x0000000f 0x00000000 0x00000000 0x80000000 + 0x01000000 0x00000000 0x00000000 0x0000000f 0x80020000 0x00000000 0x00010000>; + + /* Inbound 2GB range starting at 0 */ + dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x0 0x80000000>; + + /* This drives busses 10 to 0x1f */ + bus-range = <0x30 0x3f>; + + /* Legacy interrupts (note the weird polarity, the bridge seems + * to invert PCIe legacy interrupts). + * We are de-swizzling here because the numbers are actually for + * port of the root complex virtual P2P bridge. But I want + * to avoid putting a node for it in the tree, so the numbers + * below are basically de-swizzled numbers. + * The real slot is on idsel 0, so the swizzling is 1:1 + */ + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = < + 0x0 0x0 0x0 0x1 &UIC3 0x8 0x4 /* swizzled int A */ + 0x0 0x0 0x0 0x2 &UIC3 0x9 0x4 /* swizzled int B */ + 0x0 0x0 0x0 0x3 &UIC3 0xa 0x4 /* swizzled int C */ + 0x0 0x0 0x0 0x4 &UIC3 0xb 0x4 /* swizzled int D */>; }; }; + chosen { linux,stdout-path = "/plb/opb/serial@ef600200"; }; -- cgit v1.2.1 From 499f49026e25e74dc617bb0d96ed6e85a67f4980 Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Thu, 6 May 2010 21:43:43 +0000 Subject: powerpc/44x: Add reset-type to katmai.dts Katmai needs "reset-type" = "chip reset" (2) to correctly reboot the board. Signed-off-by: Stefan Roese Cc: Josh Boyer Signed-off-by: Josh Boyer --- arch/powerpc/boot/dts/katmai.dts | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/powerpc/boot/dts') diff --git a/arch/powerpc/boot/dts/katmai.dts b/arch/powerpc/boot/dts/katmai.dts index 8cf2c0c88c05..7c3be5e45748 100644 --- a/arch/powerpc/boot/dts/katmai.dts +++ b/arch/powerpc/boot/dts/katmai.dts @@ -44,6 +44,7 @@ d-cache-size = <32768>; dcr-controller; dcr-access-method = "native"; + reset-type = <2>; /* Use chip-reset */ }; }; -- cgit v1.2.1 From a89eda26753311d8ff2da64da621714b2f8d5dcc Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Tue, 11 May 2010 03:55:34 +0000 Subject: powerpc/44x: Add basic ICON PPC440SPe board support ICON is based on the AppliedMicro 440SPe. It is equipped with 64MByte NOR FLASH, SODIMM, Gigabit ethernet, SM502 on PCI(X), LSI SAS1068E on PCIe0 and custom FPGA on PCIe1. Signed-off-by: Stefan Roese Cc: Josh Boyer Signed-off-by: Josh Boyer --- arch/powerpc/boot/dts/icon.dts | 447 +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 447 insertions(+) create mode 100644 arch/powerpc/boot/dts/icon.dts (limited to 'arch/powerpc/boot/dts') diff --git a/arch/powerpc/boot/dts/icon.dts b/arch/powerpc/boot/dts/icon.dts new file mode 100644 index 000000000000..abcd0caeccae --- /dev/null +++ b/arch/powerpc/boot/dts/icon.dts @@ -0,0 +1,447 @@ +/* + * Device Tree Source for Mosaix Technologies, Inc. ICON board + * + * Copyright 2010 DENX Software Engineering, Stefan Roese + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without + * any warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +/ { + #address-cells = <2>; + #size-cells = <2>; + model = "mosaixtech,icon"; + compatible = "mosaixtech,icon"; + dcr-parent = <&{/cpus/cpu@0}>; + + aliases { + ethernet0 = &EMAC0; + serial0 = &UART0; + serial1 = &UART1; + serial2 = &UART2; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + model = "PowerPC,440SPe"; + reg = <0x00000000>; + clock-frequency = <0>; /* Filled in by U-Boot */ + timebase-frequency = <0>; /* Filled in by U-Boot */ + i-cache-line-size = <32>; + d-cache-line-size = <32>; + i-cache-size = <32768>; + d-cache-size = <32768>; + dcr-controller; + dcr-access-method = "native"; + reset-type = <2>; /* Use chip-reset */ + }; + }; + + memory { + device_type = "memory"; + reg = <0x0 0x00000000 0x0 0x00000000>; /* Filled in by U-Boot */ + }; + + UIC0: interrupt-controller0 { + compatible = "ibm,uic-440spe","ibm,uic"; + interrupt-controller; + cell-index = <0>; + dcr-reg = <0x0c0 0x009>; + #address-cells = <0>; + #size-cells = <0>; + #interrupt-cells = <2>; + }; + + UIC1: interrupt-controller1 { + compatible = "ibm,uic-440spe","ibm,uic"; + interrupt-controller; + cell-index = <1>; + dcr-reg = <0x0d0 0x009>; + #address-cells = <0>; + #size-cells = <0>; + #interrupt-cells = <2>; + interrupts = <0x1e 0x4 0x1f 0x4>; /* cascade */ + interrupt-parent = <&UIC0>; + }; + + UIC2: interrupt-controller2 { + compatible = "ibm,uic-440spe","ibm,uic"; + interrupt-controller; + cell-index = <2>; + dcr-reg = <0x0e0 0x009>; + #address-cells = <0>; + #size-cells = <0>; + #interrupt-cells = <2>; + interrupts = <0xa 0x4 0xb 0x4>; /* cascade */ + interrupt-parent = <&UIC0>; + }; + + UIC3: interrupt-controller3 { + compatible = "ibm,uic-440spe","ibm,uic"; + interrupt-controller; + cell-index = <3>; + dcr-reg = <0x0f0 0x009>; + #address-cells = <0>; + #size-cells = <0>; + #interrupt-cells = <2>; + interrupts = <0x10 0x4 0x11 0x4>; /* cascade */ + interrupt-parent = <&UIC0>; + }; + + SDR0: sdr { + compatible = "ibm,sdr-440spe"; + dcr-reg = <0x00e 0x002>; + }; + + CPR0: cpr { + compatible = "ibm,cpr-440spe"; + dcr-reg = <0x00c 0x002>; + }; + + MQ0: mq { + compatible = "ibm,mq-440spe"; + dcr-reg = <0x040 0x020>; + }; + + plb { + compatible = "ibm,plb-440spe", "ibm,plb-440gp", "ibm,plb4"; + #address-cells = <2>; + #size-cells = <1>; + /* addr-child addr-parent size */ + ranges = <0x4 0x00100000 0x4 0x00100000 0x00001000 + 0x4 0x00200000 0x4 0x00200000 0x00000400 + 0x4 0xe0000000 0x4 0xe0000000 0x20000000 + 0xc 0x00000000 0xc 0x00000000 0x20000000 + 0xd 0x00000000 0xd 0x00000000 0x80000000 + 0xd 0x80000000 0xd 0x80000000 0x80000000 + 0xe 0x00000000 0xe 0x00000000 0x80000000 + 0xe 0x80000000 0xe 0x80000000 0x80000000 + 0xf 0x00000000 0xf 0x00000000 0x80000000 + 0xf 0x80000000 0xf 0x80000000 0x80000000>; + clock-frequency = <0>; /* Filled in by U-Boot */ + + SDRAM0: sdram { + compatible = "ibm,sdram-440spe", "ibm,sdram-405gp"; + dcr-reg = <0x010 0x002>; + }; + + MAL0: mcmal { + compatible = "ibm,mcmal-440spe", "ibm,mcmal2"; + dcr-reg = <0x180 0x062>; + num-tx-chans = <2>; + num-rx-chans = <1>; + interrupt-parent = <&MAL0>; + interrupts = <0x0 0x1 0x2 0x3 0x4>; + #interrupt-cells = <1>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-map = ; + }; + + POB0: opb { + compatible = "ibm,opb-440spe", "ibm,opb-440gp", "ibm,opb"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0xe0000000 0x00000004 0xe0000000 0x20000000>; + clock-frequency = <0>; /* Filled in by U-Boot */ + + EBC0: ebc { + compatible = "ibm,ebc-440spe", "ibm,ebc-440gp", "ibm,ebc"; + dcr-reg = <0x012 0x002>; + #address-cells = <2>; + #size-cells = <1>; + clock-frequency = <0>; /* Filled in by U-Boot */ + /* ranges property is supplied by U-Boot */ + interrupts = <0x5 0x1>; + interrupt-parent = <&UIC1>; + + nor_flash@0,0 { + compatible = "cfi-flash"; + bank-width = <2>; + reg = <0x00000000 0x00000000 0x01000000>; + #address-cells = <1>; + #size-cells = <1>; + partition@0 { + label = "kernel"; + reg = <0x00000000 0x001e0000>; + }; + partition@1e0000 { + label = "dtb"; + reg = <0x001e0000 0x00020000>; + }; + partition@200000 { + label = "root"; + reg = <0x00200000 0x00200000>; + }; + partition@400000 { + label = "user"; + reg = <0x00400000 0x00b60000>; + }; + partition@f60000 { + label = "env"; + reg = <0x00f60000 0x00040000>; + }; + partition@fa0000 { + label = "u-boot"; + reg = <0x00fa0000 0x00060000>; + }; + }; + + SysACE_CompactFlash: sysace@1,0 { + compatible = "xlnx,sysace"; + interrupt-parent = <&UIC2>; + interrupts = <24 0x4>; + reg = <0x00000001 0x00000000 0x10000>; + }; + }; + + UART0: serial@f0000200 { + device_type = "serial"; + compatible = "ns16550"; + reg = <0xf0000200 0x00000008>; + virtual-reg = <0xa0000200>; + clock-frequency = <0>; /* Filled in by U-Boot */ + current-speed = <115200>; + interrupt-parent = <&UIC0>; + interrupts = <0x0 0x4>; + }; + + UART1: serial@f0000300 { + device_type = "serial"; + compatible = "ns16550"; + reg = <0xf0000300 0x00000008>; + virtual-reg = <0xa0000300>; + clock-frequency = <0>; + current-speed = <0>; + interrupt-parent = <&UIC0>; + interrupts = <0x1 0x4>; + }; + + + UART2: serial@f0000600 { + device_type = "serial"; + compatible = "ns16550"; + reg = <0xf0000600 0x00000008>; + virtual-reg = <0xa0000600>; + clock-frequency = <0>; + current-speed = <0>; + interrupt-parent = <&UIC1>; + interrupts = <0x5 0x4>; + }; + + IIC0: i2c@f0000400 { + compatible = "ibm,iic-440spe", "ibm,iic-440gp", "ibm,iic"; + reg = <0xf0000400 0x00000014>; + interrupt-parent = <&UIC0>; + interrupts = <0x2 0x4>; + }; + + IIC1: i2c@f0000500 { + compatible = "ibm,iic-440spe", "ibm,iic-440gp", "ibm,iic"; + reg = <0xf0000500 0x00000014>; + interrupt-parent = <&UIC0>; + interrupts = <0x3 0x4>; + #address-cells = <1>; + #size-cells = <0>; + + rtc@68 { + compatible = "stm,m41t00"; + reg = <0x68>; + }; + }; + + EMAC0: ethernet@f0000800 { + linux,network-index = <0x0>; + device_type = "network"; + compatible = "ibm,emac-440spe", "ibm,emac4"; + interrupt-parent = <&UIC1>; + interrupts = <0x1c 0x4 0x1d 0x4>; + reg = <0xf0000800 0x00000074>; + local-mac-address = [000000000000]; + mal-device = <&MAL0>; + mal-tx-channel = <0>; + mal-rx-channel = <0>; + cell-index = <0>; + max-frame-size = <9000>; + rx-fifo-size = <4096>; + tx-fifo-size = <2048>; + phy-mode = "gmii"; + phy-map = <0x00000000>; + has-inverted-stacr-oc; + has-new-stacr-staopc; + }; + }; + + PCIX0: pci@c0ec00000 { + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "ibm,plb-pcix-440spe", "ibm,plb-pcix"; + primary; + large-inbound-windows; + enable-msi-hole; + reg = <0x0000000c 0x0ec00000 0x00000008 /* Config space access */ + 0x00000000 0x00000000 0x00000000 /* no IACK cycles */ + 0x0000000c 0x0ed00000 0x00000004 /* Special cycles */ + 0x0000000c 0x0ec80000 0x00000100 /* Internal registers */ + 0x0000000c 0x0ec80100 0x000000fc>; /* Internal messaging registers */ + + /* Outbound ranges, one memory and one IO, + * later cannot be changed + */ + ranges = <0x02000000 0x00000000 0x80000000 0x0000000d 0x80000000 0x00000000 0x80000000 + 0x01000000 0x00000000 0x00000000 0x0000000c 0x08000000 0x00000000 0x00010000>; + + /* Inbound 4GB range starting at 0 */ + dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x1 0x00000000>; + + /* This drives busses 0 to 0xf */ + bus-range = <0x0 0xf>; + + /* PCI-X interrupt (SM502) is routed to extIRQ10 (UIC1, 19) */ + interrupt-map-mask = <0x0 0x0 0x0 0x0>; + interrupt-map = <0x0 0x0 0x0 0x0 &UIC1 19 0x8>; + }; + + PCIE0: pciex@d00000000 { + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "ibm,plb-pciex-440spe", "ibm,plb-pciex"; + primary; + port = <0x0>; /* port number */ + reg = <0x0000000d 0x00000000 0x20000000 /* Config space access */ + 0x0000000c 0x10000000 0x00001000>; /* Registers */ + dcr-reg = <0x100 0x020>; + sdr-base = <0x300>; + + /* Outbound ranges, one memory and one IO, + * later cannot be changed + */ + ranges = <0x02000000 0x00000000 0x80000000 0x0000000e 0x00000000 0x00000000 0x80000000 + 0x01000000 0x00000000 0x00000000 0x0000000f 0x80000000 0x00000000 0x00010000>; + + /* Inbound 4GB range starting at 0 */ + dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x1 0x00000000>; + + /* This drives busses 0x10 to 0x1f */ + bus-range = <0x10 0x1f>; + + /* Legacy interrupts (note the weird polarity, the bridge seems + * to invert PCIe legacy interrupts). + * We are de-swizzling here because the numbers are actually for + * port of the root complex virtual P2P bridge. But I want + * to avoid putting a node for it in the tree, so the numbers + * below are basically de-swizzled numbers. + * The real slot is on idsel 0, so the swizzling is 1:1 + */ + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = < + 0x0 0x0 0x0 0x1 &UIC3 0x0 0x4 /* swizzled int A */ + 0x0 0x0 0x0 0x2 &UIC3 0x1 0x4 /* swizzled int B */ + 0x0 0x0 0x0 0x3 &UIC3 0x2 0x4 /* swizzled int C */ + 0x0 0x0 0x0 0x4 &UIC3 0x3 0x4 /* swizzled int D */>; + }; + + PCIE1: pciex@d20000000 { + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "ibm,plb-pciex-440spe", "ibm,plb-pciex"; + primary; + port = <0x1>; /* port number */ + reg = <0x0000000d 0x20000000 0x20000000 /* Config space access */ + 0x0000000c 0x10001000 0x00001000>; /* Registers */ + dcr-reg = <0x120 0x020>; + sdr-base = <0x340>; + + /* Outbound ranges, one memory and one IO, + * later cannot be changed + */ + ranges = <0x02000000 0x00000000 0x80000000 0x0000000e 0x80000000 0x00000000 0x80000000 + 0x01000000 0x00000000 0x00000000 0x0000000f 0x80010000 0x00000000 0x00010000>; + + /* Inbound 4GB range starting at 0 */ + dma-ranges = <0x42000000 0x0 0x0 0x0 0x0 0x1 0x00000000>; + + /* This drives busses 0x20 to 0x2f */ + bus-range = <0x20 0x2f>; + + /* Legacy interrupts (note the weird polarity, the bridge seems + * to invert PCIe legacy interrupts). + * We are de-swizzling here because the numbers are actually for + * port of the root complex virtual P2P bridge. But I want + * to avoid putting a node for it in the tree, so the numbers + * below are basically de-swizzled numbers. + * The real slot is on idsel 0, so the swizzling is 1:1 + */ + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = < + 0x0 0x0 0x0 0x1 &UIC3 0x4 0x4 /* swizzled int A */ + 0x0 0x0 0x0 0x2 &UIC3 0x5 0x4 /* swizzled int B */ + 0x0 0x0 0x0 0x3 &UIC3 0x6 0x4 /* swizzled int C */ + 0x0 0x0 0x0 0x4 &UIC3 0x7 0x4 /* swizzled int D */>; + }; + + I2O: i2o@400100000 { + compatible = "ibm,i2o-440spe"; + reg = <0x00000004 0x00100000 0x100>; + dcr-reg = <0x060 0x020>; + }; + + DMA0: dma0@400100100 { + compatible = "ibm,dma-440spe"; + cell-index = <0>; + reg = <0x00000004 0x00100100 0x100>; + dcr-reg = <0x060 0x020>; + interrupt-parent = <&DMA0>; + interrupts = <0 1>; + #interrupt-cells = <1>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-map = < + 0 &UIC0 0x14 4 + 1 &UIC1 0x16 4>; + }; + + DMA1: dma1@400100200 { + compatible = "ibm,dma-440spe"; + cell-index = <1>; + reg = <0x00000004 0x00100200 0x100>; + dcr-reg = <0x060 0x020>; + interrupt-parent = <&DMA1>; + interrupts = <0 1>; + #interrupt-cells = <1>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-map = < + 0 &UIC0 0x16 4 + 1 &UIC1 0x16 4>; + }; + + xor-accel@400200000 { + compatible = "amcc,xor-accelerator"; + reg = <0x00000004 0x00200000 0x400>; + interrupt-parent = <&UIC1>; + interrupts = <0x1f 4>; + }; + }; + + chosen { + linux,stdout-path = "/plb/opb/serial@f0000200"; + }; +}; -- cgit v1.2.1 From 0472fd0755fed200c750ba57e5ea46f941914adb Mon Sep 17 00:00:00 2001 From: Andy Fleming Date: Mon, 29 Mar 2010 20:39:08 -0500 Subject: powerpc/85xx: Enable support for ports 3 and 4 on 8548 CDS I believe support was disabled due to issues with earlier versions of the board/processor. At worst, adding the ports back into the device tree should result in enabling ports that don't work on older systems, so the default should be to enable them. Signed-off-by: Andy Fleming Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mpc8548cds.dts | 4 ---- 1 file changed, 4 deletions(-) (limited to 'arch/powerpc/boot/dts') diff --git a/arch/powerpc/boot/dts/mpc8548cds.dts b/arch/powerpc/boot/dts/mpc8548cds.dts index 4173af387c63..0f5262452682 100644 --- a/arch/powerpc/boot/dts/mpc8548cds.dts +++ b/arch/powerpc/boot/dts/mpc8548cds.dts @@ -20,10 +20,8 @@ aliases { ethernet0 = &enet0; ethernet1 = &enet1; -/* ethernet2 = &enet2; ethernet3 = &enet3; -*/ serial0 = &serial0; serial1 = &serial1; pci0 = &pci0; @@ -254,7 +252,6 @@ }; }; -/* eTSEC 3/4 are currently broken enet2: ethernet@26000 { #address-cells = <1>; #size-cells = <1>; @@ -310,7 +307,6 @@ }; }; }; - */ serial0: serial@4500 { cell-index = <0>; -- cgit v1.2.1 From 710e33832653cccf7fc432023e7dbe8c49a1902f Mon Sep 17 00:00:00 2001 From: Li Yang Date: Thu, 22 Apr 2010 16:31:38 +0800 Subject: powerpc/85xx: Change MPC8572DS camp dtses for MSI sharing Enable the sharing of MSI interrupt through AMP OSes in the mpc8572ds dtses. Signed-off-by: Zhao Chenhui Signed-off-by: Li Yang Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mpc8572ds_camp_core0.dts | 15 +++++++++++++-- arch/powerpc/boot/dts/mpc8572ds_camp_core1.dts | 7 ++----- 2 files changed, 15 insertions(+), 7 deletions(-) (limited to 'arch/powerpc/boot/dts') diff --git a/arch/powerpc/boot/dts/mpc8572ds_camp_core0.dts b/arch/powerpc/boot/dts/mpc8572ds_camp_core0.dts index 5bd1011fde96..3375c2ab0c32 100644 --- a/arch/powerpc/boot/dts/mpc8572ds_camp_core0.dts +++ b/arch/powerpc/boot/dts/mpc8572ds_camp_core0.dts @@ -215,6 +215,18 @@ clock-frequency = <0>; }; + msi@41600 { + compatible = "fsl,mpc8572-msi", "fsl,mpic-msi"; + reg = <0x41600 0x80>; + msi-available-ranges = <0 0x80>; + interrupts = < + 0xe0 0 + 0xe1 0 + 0xe2 0 + 0xe3 0>; + interrupt-parent = <&mpic>; + }; + global-utilities@e0000 { //global utilities block compatible = "fsl,mpc8572-guts"; reg = <0xe0000 0x1000>; @@ -243,8 +255,7 @@ protected-sources = < 31 32 33 37 38 39 /* enet2 enet3 */ 76 77 78 79 26 42 /* dma2 pci2 serial*/ - 0xe0 0xe1 0xe2 0xe3 /* msi */ - 0xe4 0xe5 0xe6 0xe7 + 0xe4 0xe5 0xe6 0xe7 /* msi */ >; }; }; diff --git a/arch/powerpc/boot/dts/mpc8572ds_camp_core1.dts b/arch/powerpc/boot/dts/mpc8572ds_camp_core1.dts index 0efc3456e297..e7b477f6a3fe 100644 --- a/arch/powerpc/boot/dts/mpc8572ds_camp_core1.dts +++ b/arch/powerpc/boot/dts/mpc8572ds_camp_core1.dts @@ -154,12 +154,8 @@ msi@41600 { compatible = "fsl,mpc8572-msi", "fsl,mpic-msi"; reg = <0x41600 0x80>; - msi-available-ranges = <0 0x100>; + msi-available-ranges = <0x80 0x80>; interrupts = < - 0xe0 0 - 0xe1 0 - 0xe2 0 - 0xe3 0 0xe4 0 0xe5 0 0xe6 0 @@ -190,6 +186,7 @@ 0x1 0x2 0x3 0x4 /* pci slot */ 0x9 0xa 0xb 0xc /* usb */ 0x6 0x7 0xe 0x5 /* Audio elgacy SATA */ + 0xe0 0xe1 0xe2 0xe3 /* msi */ >; }; }; -- cgit v1.2.1 From 48936a08b85518c22a9467a8eaac35d43af54ab4 Mon Sep 17 00:00:00 2001 From: Haiying Wang Date: Fri, 21 May 2010 10:16:12 -0400 Subject: powerpc/85xx: Add P1021MDS board support P1021 is a dual e500v2 core based SOC with: * 3 eTSECs (eTSEC1/3 RGMII, eTSEC2 SGMII on this board) * 2 PCIe Controller * 1 USB2.0 controller * eSDHC, eSPI, I2C, DUART * eLBC (NAND, BCSR, PMC0/1) * Security Engine (SEC 3.3.2) * Quicc Engine (QE) Signed-off-by: Haiying Wang Signed-off-by: Yu Liu Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/p1021mds.dts | 698 +++++++++++++++++++++++++++++++++++++ 1 file changed, 698 insertions(+) create mode 100644 arch/powerpc/boot/dts/p1021mds.dts (limited to 'arch/powerpc/boot/dts') diff --git a/arch/powerpc/boot/dts/p1021mds.dts b/arch/powerpc/boot/dts/p1021mds.dts new file mode 100644 index 000000000000..7fad2df25981 --- /dev/null +++ b/arch/powerpc/boot/dts/p1021mds.dts @@ -0,0 +1,698 @@ +/* + * P1021 MDS Device Tree Source + * + * Copyright 2010 Freescale Semiconductor Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +/dts-v1/; +/ { + model = "fsl,P1021"; + compatible = "fsl,P1021MDS"; + #address-cells = <2>; + #size-cells = <2>; + + aliases { + serial0 = &serial0; + serial1 = &serial1; + ethernet0 = &enet0; + ethernet1 = &enet1; + ethernet2 = &enet2; + ethernet3 = &enet3; + ethernet4 = &enet4; + pci0 = &pci0; + pci1 = &pci1; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + PowerPC,P1021@0 { + device_type = "cpu"; + reg = <0x0>; + next-level-cache = <&L2>; + }; + + PowerPC,P1021@1 { + device_type = "cpu"; + reg = <0x1>; + next-level-cache = <&L2>; + }; + }; + + memory { + device_type = "memory"; + }; + + localbus@ffe05000 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "fsl,p1021-elbc", "fsl,elbc", "simple-bus"; + reg = <0 0xffe05000 0 0x1000>; + interrupts = <19 2>; + interrupt-parent = <&mpic>; + + /* NAND Flash, BCSR, PMC0/1*/ + ranges = <0x0 0x0 0x0 0xfc000000 0x02000000 + 0x1 0x0 0x0 0xf8000000 0x00008000 + 0x2 0x0 0x0 0xf8010000 0x00020000 + 0x3 0x0 0x0 0xf8020000 0x00020000>; + + nand@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,p1021-fcm-nand", + "fsl,elbc-fcm-nand"; + reg = <0x0 0x0 0x40000>; + + partition@0 { + /* This location must not be altered */ + /* 1MB for u-boot Bootloader Image */ + reg = <0x0 0x00100000>; + label = "NAND (RO) U-Boot Image"; + read-only; + }; + + partition@100000 { + /* 1MB for DTB Image */ + reg = <0x00100000 0x00100000>; + label = "NAND (RO) DTB Image"; + read-only; + }; + + partition@200000 { + /* 4MB for Linux Kernel Image */ + reg = <0x00200000 0x00400000>; + label = "NAND (RO) Linux Kernel Image"; + read-only; + }; + + partition@600000 { + /* 5MB for Compressed Root file System Image */ + reg = <0x00600000 0x00500000>; + label = "NAND (RO) Compressed RFS Image"; + read-only; + }; + + partition@b00000 { + /* 6MB for JFFS2 based Root file System */ + reg = <0x00a00000 0x00600000>; + label = "NAND (RW) JFFS2 Root File System"; + }; + + partition@1100000 { + /* 14MB for JFFS2 based Root file System */ + reg = <0x01100000 0x00e00000>; + label = "NAND (RW) Writable User area"; + }; + + partition@1f00000 { + /* 1MB for microcode */ + reg = <0x01f00000 0x00100000>; + label = "NAND (RO) QE Ucode"; + read-only; + }; + }; + + bcsr@1,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,p1021mds-bcsr"; + reg = <1 0 0x8000>; + ranges = <0 1 0 0x8000>; + }; + + pib@2,0 { + compatible = "fsl,p1021mds-pib"; + reg = <2 0 0x10000>; + }; + + pib@3,0 { + compatible = "fsl,p1021mds-pib"; + reg = <3 0 0x10000>; + }; + }; + + soc@ffe00000 { + + #address-cells = <1>; + #size-cells = <1>; + device_type = "soc"; + compatible = "fsl,p1021-immr", "simple-bus"; + ranges = <0x0 0x0 0xffe00000 0x100000>; + bus-frequency = <0>; // Filled out by uboot. + + ecm-law@0 { + compatible = "fsl,ecm-law"; + reg = <0x0 0x1000>; + fsl,num-laws = <12>; + }; + + ecm@1000 { + compatible = "fsl,p1021-ecm", "fsl,ecm"; + reg = <0x1000 0x1000>; + interrupts = <16 2>; + interrupt-parent = <&mpic>; + }; + + memory-controller@2000 { + compatible = "fsl,p1021-memory-controller"; + reg = <0x2000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <16 2>; + }; + + i2c@3000 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + compatible = "fsl-i2c"; + reg = <0x3000 0x100>; + interrupts = <43 2>; + interrupt-parent = <&mpic>; + dfsrr; + rtc@68 { + compatible = "dallas,ds1374"; + reg = <0x68>; + }; + }; + + i2c@3100 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <1>; + compatible = "fsl-i2c"; + reg = <0x3100 0x100>; + interrupts = <43 2>; + interrupt-parent = <&mpic>; + dfsrr; + }; + + serial0: serial@4500 { + cell-index = <0>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x4500 0x100>; + clock-frequency = <0>; + interrupts = <42 2>; + interrupt-parent = <&mpic>; + }; + + serial1: serial@4600 { + cell-index = <1>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x4600 0x100>; + clock-frequency = <0>; + interrupts = <42 2>; + interrupt-parent = <&mpic>; + }; + + spi@7000 { + cell-index = <0>; + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,espi"; + reg = <0x7000 0x1000>; + interrupts = <59 0x2>; + interrupt-parent = <&mpic>; + espi,num-ss-bits = <4>; + mode = "cpu"; + + fsl_m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,espi-flash"; + reg = <0>; + linux,modalias = "fsl_m25p80"; + spi-max-frequency = <40000000>; /* input clock */ + partition@u-boot { + label = "u-boot-spi"; + reg = <0x00000000 0x00100000>; + read-only; + }; + partition@kernel { + label = "kernel-spi"; + reg = <0x00100000 0x00500000>; + read-only; + }; + partition@dtb { + label = "dtb-spi"; + reg = <0x00600000 0x00100000>; + read-only; + }; + partition@fs { + label = "file system-spi"; + reg = <0x00700000 0x00900000>; + }; + }; + }; + + gpio: gpio-controller@f000 { + #gpio-cells = <2>; + compatible = "fsl,mpc8572-gpio"; + reg = <0xf000 0x100>; + interrupts = <47 0x2>; + interrupt-parent = <&mpic>; + gpio-controller; + }; + + L2: l2-cache-controller@20000 { + compatible = "fsl,p1021-l2-cache-controller"; + reg = <0x20000 0x1000>; + cache-line-size = <32>; // 32 bytes + cache-size = <0x40000>; // L2,256K + interrupt-parent = <&mpic>; + interrupts = <16 2>; + }; + + dma@21300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,eloplus-dma"; + reg = <0x21300 0x4>; + ranges = <0x0 0x21100 0x200>; + cell-index = <0>; + dma-channel@0 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x0 0x80>; + cell-index = <0>; + interrupt-parent = <&mpic>; + interrupts = <20 2>; + }; + dma-channel@80 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + cell-index = <1>; + interrupt-parent = <&mpic>; + interrupts = <21 2>; + }; + dma-channel@100 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + cell-index = <2>; + interrupt-parent = <&mpic>; + interrupts = <22 2>; + }; + dma-channel@180 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + cell-index = <3>; + interrupt-parent = <&mpic>; + interrupts = <23 2>; + }; + }; + + usb@22000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl-usb2-dr"; + reg = <0x22000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <28 0x2>; + phy_type = "ulpi"; + }; + + mdio@24000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,etsec2-mdio"; + reg = <0x24000 0x1000 0xb0030 0x4>; + + phy0: ethernet-phy@0 { + interrupt-parent = <&mpic>; + interrupts = <1 1>; + reg = <0x0>; + }; + phy1: ethernet-phy@1 { + interrupt-parent = <&mpic>; + interrupts = <2 1>; + reg = <0x1>; + }; + phy4: ethernet-phy@4 { + interrupt-parent = <&mpic>; + reg = <0x4>; + }; + }; + + mdio@25000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,etsec2-tbi"; + reg = <0x25000 0x1000 0xb1030 0x4>; + tbi0: tbi-phy@11 { + reg = <0x11>; + device_type = "tbi-phy"; + }; + }; + + enet0: ethernet@B0000 { + #address-cells = <1>; + #size-cells = <1>; + cell-index = <0>; + device_type = "network"; + model = "eTSEC"; + compatible = "fsl,etsec2"; + fsl,num_rx_queues = <0x8>; + fsl,num_tx_queues = <0x8>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupt-parent = <&mpic>; + phy-handle = <&phy0>; + phy-connection-type = "rgmii-id"; + queue-group@0{ + #address-cells = <1>; + #size-cells = <1>; + reg = <0xB0000 0x1000>; + interrupts = <29 2 30 2 34 2>; + }; + queue-group@1{ + #address-cells = <1>; + #size-cells = <1>; + reg = <0xB4000 0x1000>; + interrupts = <17 2 18 2 24 2>; + }; + }; + + enet1: ethernet@B1000 { + #address-cells = <1>; + #size-cells = <1>; + cell-index = <0>; + device_type = "network"; + model = "eTSEC"; + compatible = "fsl,etsec2"; + fsl,num_rx_queues = <0x8>; + fsl,num_tx_queues = <0x8>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupt-parent = <&mpic>; + phy-handle = <&phy4>; + tbi-handle = <&tbi0>; + phy-connection-type = "sgmii"; + queue-group@0{ + #address-cells = <1>; + #size-cells = <1>; + reg = <0xB1000 0x1000>; + interrupts = <35 2 36 2 40 2>; + }; + queue-group@1{ + #address-cells = <1>; + #size-cells = <1>; + reg = <0xB5000 0x1000>; + interrupts = <51 2 52 2 67 2>; + }; + }; + + enet2: ethernet@B2000 { + #address-cells = <1>; + #size-cells = <1>; + cell-index = <0>; + device_type = "network"; + model = "eTSEC"; + compatible = "fsl,etsec2"; + fsl,num_rx_queues = <0x8>; + fsl,num_tx_queues = <0x8>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupt-parent = <&mpic>; + phy-handle = <&phy1>; + phy-connection-type = "rgmii-id"; + queue-group@0{ + #address-cells = <1>; + #size-cells = <1>; + reg = <0xB2000 0x1000>; + interrupts = <31 2 32 2 33 2>; + }; + queue-group@1{ + #address-cells = <1>; + #size-cells = <1>; + reg = <0xB6000 0x1000>; + interrupts = <25 2 26 2 27 2>; + }; + }; + + sdhci@2e000 { + compatible = "fsl,p1021-esdhc", "fsl,esdhc"; + reg = <0x2e000 0x1000>; + interrupts = <72 0x2>; + interrupt-parent = <&mpic>; + /* Filled in by U-Boot */ + clock-frequency = <0>; + }; + + crypto@30000 { + compatible = "fsl,sec3.3", "fsl,sec3.1", + "fsl,sec3.0", "fsl,sec2.4", + "fsl,sec2.2", "fsl,sec2.1", "fsl,sec2.0"; + reg = <0x30000 0x10000>; + interrupts = <45 2 58 2>; + interrupt-parent = <&mpic>; + fsl,num-channels = <4>; + fsl,channel-fifo-len = <24>; + fsl,exec-units-mask = <0x97c>; + fsl,descriptor-types-mask = <0x3a30abf>; + }; + + mpic: pic@40000 { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <0x40000 0x40000>; + compatible = "chrp,open-pic"; + device_type = "open-pic"; + }; + + msi@41600 { + compatible = "fsl,p1021-msi", "fsl,mpic-msi"; + reg = <0x41600 0x80>; + msi-available-ranges = <0 0x100>; + interrupts = < + 0xe0 0 + 0xe1 0 + 0xe2 0 + 0xe3 0 + 0xe4 0 + 0xe5 0 + 0xe6 0 + 0xe7 0>; + interrupt-parent = <&mpic>; + }; + + global-utilities@e0000 { //global utilities block + compatible = "fsl,p1021-guts"; + reg = <0xe0000 0x1000>; + fsl,has-rstcr; + }; + + par_io@e0100 { + #address-cells = <1>; + #size-cells = <1>; + reg = <0xe0100 0x60>; + ranges = <0x0 0xe0100 0x60>; + device_type = "par_io"; + num-ports = <3>; + pio1: ucc_pin@01 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */ + 0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */ + 0x0 0x17 0x2 0x0 0x2 0x0 /* CLK12 */ + 0x0 0x18 0x2 0x0 0x1 0x0 /* CLK9 +*/ + 0x0 0x7 0x1 0x0 0x2 0x0 /* ENET1_TXD0_SER1_TXD0 */ + 0x0 0x9 0x1 0x0 0x2 0x0 /* ENET1_TXD1_SER1_TXD1 */ + 0x0 0xb 0x1 0x0 0x2 0x0 /* ENET1_TXD2_SER1_TXD2 */ + 0x0 0xc 0x1 0x0 0x2 0x0 /* ENET1_TXD3_SER1_TXD3 */ + 0x0 0x6 0x2 0x0 0x2 0x0 /* ENET1_RXD0_SER1_RXD0 */ + 0x0 0xa 0x2 0x0 0x2 0x0 /* ENET1_RXD1_SER1_RXD1 */ + 0x0 0xe 0x2 0x0 0x2 0x0 /* ENET1_RXD2_SER1_RXD2 */ + 0x0 0xf 0x2 0x0 0x2 0x0 /* ENET1_RXD3_SER1_RXD3 */ + 0x0 0x5 0x1 0x0 0x2 0x0 /* ENET1_TX_EN_SER1_RTS_B */ + 0x0 0xd 0x1 0x0 0x2 0x0 /* ENET1_TX_ER */ + 0x0 0x4 0x2 0x0 0x2 0x0 /* ENET1_RX_DV_SER1_CTS_B */ + 0x0 0x8 0x2 0x0 0x2 0x0 /* ENET1_RX_ER_SER1_CD_B */ + 0x0 0x11 0x2 0x0 0x2 0x0 /* ENET1_CRS */ + 0x0 0x10 0x2 0x0 0x2 0x0>; /* ENET1_COL */ + }; + + pio2: ucc_pin@02 { + pio-map = < + /* port pin dir open_drain assignment has_irq */ + 0x1 0x13 0x1 0x0 0x1 0x0 /* QE_MUX_MDC */ + 0x1 0x14 0x3 0x0 0x1 0x0 /* QE_MUX_MDIO */ + 0x1 0xb 0x2 0x0 0x1 0x0 /* CLK13 */ + 0x1 0x7 0x1 0x0 0x2 0x0 /* ENET5_TXD0_SER5_TXD0 */ + 0x1 0xa 0x1 0x0 0x2 0x0 /* ENET5_TXD1_SER5_TXD1 */ + 0x1 0x6 0x2 0x0 0x2 0x0 /* ENET5_RXD0_SER5_RXD0 */ + 0x1 0x9 0x2 0x0 0x2 0x0 /* ENET5_RXD1_SER5_RXD1 */ + 0x1 0x5 0x1 0x0 0x2 0x0 /* ENET5_TX_EN_SER5_RTS_B */ + 0x1 0x4 0x2 0x0 0x2 0x0 /* ENET5_RX_DV_SER5_CTS_B */ + 0x1 0x8 0x2 0x0 0x2 0x0>; /* ENET5_RX_ER_SER5_CD_B */ + }; + }; + }; + + pci0: pcie@ffe09000 { + compatible = "fsl,mpc8548-pcie"; + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0 0xffe09000 0 0x1000>; + bus-range = <0 255>; + ranges = <0x2000000 0x0 0xa0000000 0 0xa0000000 0x0 0x20000000 + 0x1000000 0x0 0x00000000 0 0xffc10000 0x0 0x10000>; + clock-frequency = <33333333>; + interrupt-parent = <&mpic>; + interrupts = <16 2>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = < + /* IDSEL 0x0 */ + 0000 0 0 1 &mpic 4 1 + 0000 0 0 2 &mpic 5 1 + 0000 0 0 3 &mpic 6 1 + 0000 0 0 4 &mpic 7 1 + >; + pcie@0 { + reg = <0x0 0x0 0x0 0x0 0x0>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + ranges = <0x2000000 0x0 0xa0000000 + 0x2000000 0x0 0xa0000000 + 0x0 0x20000000 + + 0x1000000 0x0 0x0 + 0x1000000 0x0 0x0 + 0x0 0x100000>; + }; + }; + + pci1: pcie@ffe0a000 { + compatible = "fsl,mpc8548-pcie"; + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0 0xffe0a000 0 0x1000>; + bus-range = <0 255>; + ranges = <0x2000000 0x0 0xc0000000 0 0xc0000000 0x0 0x20000000 + 0x1000000 0x0 0x00000000 0 0xffc20000 0x0 0x10000>; + clock-frequency = <33333333>; + interrupt-parent = <&mpic>; + interrupts = <16 2>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = < + /* IDSEL 0x0 */ + 0000 0 0 1 &mpic 0 1 + 0000 0 0 2 &mpic 1 1 + 0000 0 0 3 &mpic 2 1 + 0000 0 0 4 &mpic 3 1 + >; + pcie@0 { + reg = <0x0 0x0 0x0 0x0 0x0>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + ranges = <0x2000000 0x0 0xc0000000 + 0x2000000 0x0 0xc0000000 + 0x0 0x20000000 + + 0x1000000 0x0 0x0 + 0x1000000 0x0 0x0 + 0x0 0x100000>; + }; + }; + + qe@ffe80000 { + #address-cells = <1>; + #size-cells = <1>; + device_type = "qe"; + compatible = "fsl,qe"; + ranges = <0x0 0x0 0xffe80000 0x40000>; + reg = <0 0xffe80000 0 0x480>; + brg-frequency = <0>; + bus-frequency = <0>; + fsl,qe-num-riscs = <1>; + fsl,qe-num-snums = <28>; + + qeic: interrupt-controller@80 { + interrupt-controller; + compatible = "fsl,qe-ic"; + #address-cells = <0>; + #interrupt-cells = <1>; + reg = <0x80 0x80>; + interrupts = <63 2 60 2>; //high:47 low:44 + interrupt-parent = <&mpic>; + }; + + enet3: ucc@2000 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <1>; + reg = <0x2000 0x200>; + interrupts = <32>; + interrupt-parent = <&qeic>; + local-mac-address = [ 00 00 00 00 00 00 ]; + rx-clock-name = "clk12"; + tx-clock-name = "clk9"; + pio-handle = <&pio1>; + phy-handle = <&qe_phy0>; + phy-connection-type = "mii"; + }; + + mdio@2120 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x2120 0x18>; + compatible = "fsl,ucc-mdio"; + + qe_phy0: ethernet-phy@0 { + interrupt-parent = <&mpic>; + interrupts = <4 1>; + reg = <0x0>; + device_type = "ethernet-phy"; + }; + qe_phy1: ethernet-phy@03 { + interrupt-parent = <&mpic>; + interrupts = <5 1>; + reg = <0x3>; + device_type = "ethernet-phy"; + }; + tbi-phy@11 { + reg = <0x11>; + device_type = "tbi-phy"; + }; + }; + + enet4: ucc@2400 { + device_type = "network"; + compatible = "ucc_geth"; + cell-index = <5>; + reg = <0x2400 0x200>; + interrupts = <40>; + interrupt-parent = <&qeic>; + local-mac-address = [ 00 00 00 00 00 00 ]; + rx-clock-name = "none"; + tx-clock-name = "clk13"; + pio-handle = <&pio2>; + phy-handle = <&qe_phy1>; + phy-connection-type = "rmii"; + }; + + muram@10000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,qe-muram", "fsl,cpm-muram"; + ranges = <0x0 0x10000 0x6000>; + + data-only@0 { + compatible = "fsl,qe-muram-data", + "fsl,cpm-muram-data"; + reg = <0x0 0x6000>; + }; + }; + }; +}; -- cgit v1.2.1 From a2c9a603c72be0d9a0780f196bff53ab0d517347 Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Fri, 11 Jun 2010 01:52:34 +0000 Subject: powerpc/5200: add lite5200 onboard I2C eeprom and flash Add dts descriptions for onboard 256 byte I2C eeprom (pcf8582C-2) and 16MB NOR flash (am29lv652d). Signed-off-by: Dmitry Eremin-Solenikov [grant.likely@secretlab.ca: added lite5200b eeprom and declared lite5200 gpios] Signed-off-by: Grant Likely --- arch/powerpc/boot/dts/lite5200.dts | 24 ++++++++++++++++++++++++ arch/powerpc/boot/dts/lite5200b.dts | 5 +++++ 2 files changed, 29 insertions(+) (limited to 'arch/powerpc/boot/dts') diff --git a/arch/powerpc/boot/dts/lite5200.dts b/arch/powerpc/boot/dts/lite5200.dts index 82ff2b13bc37..d1502ef85edb 100644 --- a/arch/powerpc/boot/dts/lite5200.dts +++ b/arch/powerpc/boot/dts/lite5200.dts @@ -134,12 +134,16 @@ compatible = "fsl,mpc5200-gpio"; reg = <0xb00 0x40>; interrupts = <1 7 0>; + gpio-controller; + #gpio-cells = <2>; }; gpio@c00 { compatible = "fsl,mpc5200-gpio-wkup"; reg = <0xc00 0x40>; interrupts = <1 8 0 0 3 0>; + gpio-controller; + #gpio-cells = <2>; }; spi@f00 { @@ -255,7 +259,13 @@ compatible = "fsl,mpc5200-i2c","fsl-i2c"; reg = <0x3d40 0x40>; interrupts = <2 16 0>; + + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + }; }; + sram@8000 { compatible = "fsl,mpc5200-sram"; reg = <0x8000 0x4000>; @@ -281,4 +291,18 @@ 0x02000000 0 0xa0000000 0xa0000000 0 0x10000000 0x01000000 0 0x00000000 0xb0000000 0 0x01000000>; }; + + localbus { + compatible = "fsl,mpc5200-lpb","simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + + ranges = <0 0 0xff000000 0x01000000>; + + flash@0,0 { + compatible = "amd,am29lv652d", "cfi-flash"; + reg = <0 0 0x01000000>; + bank-width = <1>; + }; + }; }; diff --git a/arch/powerpc/boot/dts/lite5200b.dts b/arch/powerpc/boot/dts/lite5200b.dts index e45a63be3a86..59702ace900f 100644 --- a/arch/powerpc/boot/dts/lite5200b.dts +++ b/arch/powerpc/boot/dts/lite5200b.dts @@ -259,6 +259,11 @@ compatible = "fsl,mpc5200b-i2c","fsl,mpc5200-i2c","fsl-i2c"; reg = <0x3d40 0x40>; interrupts = <2 16 0>; + + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + }; }; sram@8000 { -- cgit v1.2.1 From 2b07be2493681220cac4d185494a4edb0b8efd1e Mon Sep 17 00:00:00 2001 From: Dmitry Baryshkov Date: Wed, 9 Jun 2010 21:16:20 +0000 Subject: powerpc/5200: fix lite5200 ethernet phy address According to my schematics, on Lite5200 board ethernet phy uses address 0 (all ADDR lines are pulled down). With this change I can talk to onboard phy (LXT971) and correctly use autonegotiation. Signed-off-by: Dmitry Eremin-Solenikov Signed-off-by: Grant Likely --- arch/powerpc/boot/dts/lite5200.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/powerpc/boot/dts') diff --git a/arch/powerpc/boot/dts/lite5200.dts b/arch/powerpc/boot/dts/lite5200.dts index d1502ef85edb..179a1785d645 100644 --- a/arch/powerpc/boot/dts/lite5200.dts +++ b/arch/powerpc/boot/dts/lite5200.dts @@ -234,8 +234,8 @@ reg = <0x3000 0x400>; // fec range, since we need to setup fec interrupts interrupts = <2 5 0>; // these are for "mii command finished", not link changes & co. - phy0: ethernet-phy@1 { - reg = <1>; + phy0: ethernet-phy@0 { + reg = <0>; }; }; -- cgit v1.2.1 From 9a52e392bd053f1d282488517125c6c1ab77006a Mon Sep 17 00:00:00 2001 From: Stefan Roese Date: Thu, 3 Jun 2010 22:29:59 +0000 Subject: powerpc/44x: Fix UART2/3 interrupt assignment in PPC460EX/GT dts files UART2 and UART3 on 460EX/GT have incorrect interrupt mappings right now. UART2 should be 28 (0x1c) and UART3 29 (0x1d). This patch fixes this and switches to using decimal number instead of hex, since the AppliedMicro (AMCC) users manuals describe their inerrupt numbers in decimal. Thanks to Fabien Proriol for pointing this out. Signed-off-by: Stefan Roese Cc: Fabien Proriol Cc: Josh Boyer Signed-off-by: Josh Boyer --- arch/powerpc/boot/dts/canyonlands.dts | 4 ++-- arch/powerpc/boot/dts/glacier.dts | 4 ++-- 2 files changed, 4 insertions(+), 4 deletions(-) (limited to 'arch/powerpc/boot/dts') diff --git a/arch/powerpc/boot/dts/canyonlands.dts b/arch/powerpc/boot/dts/canyonlands.dts index cd56bb5b347b..5806ef0b860b 100644 --- a/arch/powerpc/boot/dts/canyonlands.dts +++ b/arch/powerpc/boot/dts/canyonlands.dts @@ -270,7 +270,7 @@ clock-frequency = <0>; /* Filled in by U-Boot */ current-speed = <0>; /* Filled in by U-Boot */ interrupt-parent = <&UIC1>; - interrupts = <0x1d 0x4>; + interrupts = <28 0x4>; }; UART3: serial@ef600600 { @@ -281,7 +281,7 @@ clock-frequency = <0>; /* Filled in by U-Boot */ current-speed = <0>; /* Filled in by U-Boot */ interrupt-parent = <&UIC1>; - interrupts = <0x1e 0x4>; + interrupts = <29 0x4>; }; IIC0: i2c@ef600700 { diff --git a/arch/powerpc/boot/dts/glacier.dts b/arch/powerpc/boot/dts/glacier.dts index d62a4fb6f93c..e618fc4cbc9e 100644 --- a/arch/powerpc/boot/dts/glacier.dts +++ b/arch/powerpc/boot/dts/glacier.dts @@ -259,7 +259,7 @@ clock-frequency = <0>; /* Filled in by U-Boot */ current-speed = <0>; /* Filled in by U-Boot */ interrupt-parent = <&UIC1>; - interrupts = <0x1d 0x4>; + interrupts = <28 0x4>; }; UART3: serial@ef600600 { @@ -270,7 +270,7 @@ clock-frequency = <0>; /* Filled in by U-Boot */ current-speed = <0>; /* Filled in by U-Boot */ interrupt-parent = <&UIC1>; - interrupts = <0x1e 0x4>; + interrupts = <29 0x4>; }; IIC0: i2c@ef600700 { -- cgit v1.2.1 From 12fb0eb4c963452f727752aae03bbef192abed40 Mon Sep 17 00:00:00 2001 From: Anatolij Gustschin Date: Tue, 27 Jul 2010 11:26:02 +0000 Subject: powerpc/5121: add initial support for PDM360NG board Adds IFM PDM360NG device tree and platform code. Currently following is supported: - Spansion S29GL512P 256 MB NOR flash - ST Micro NAND 1 GiB flash - DIU, please use "fbcon=map:5 video=fslfb:800x480-32@60" at the kernel command line to enable PrimeView PM070WL3 Display support. - FEC - I2C - RTC, EEPROM - MSCAN - PSC UART, please pass "console=tty0 console=ttyPSC5,115200" on the kernel command line. - SPI, ADS7845 Touchscreen - USB0/1 Host - USB0 OTG Host/Device - VIU, Overlay/Capture support Signed-off-by: Markus Fischer Signed-off-by: Wolfgang Grandegger Signed-off-by: Michael Weiss Signed-off-by: Detlev Zundel Signed-off-by: Anatolij Gustschin Signed-off-by: Grant Likely --- arch/powerpc/boot/dts/pdm360ng.dts | 410 +++++++++++++++++++++++++++++++++++++ 1 file changed, 410 insertions(+) create mode 100644 arch/powerpc/boot/dts/pdm360ng.dts (limited to 'arch/powerpc/boot/dts') diff --git a/arch/powerpc/boot/dts/pdm360ng.dts b/arch/powerpc/boot/dts/pdm360ng.dts new file mode 100644 index 000000000000..94dfa5c9a7f9 --- /dev/null +++ b/arch/powerpc/boot/dts/pdm360ng.dts @@ -0,0 +1,410 @@ +/* + * Device Tree Source for IFM PDM360NG. + * + * Copyright 2009 - 2010 DENX Software Engineering. + * Anatolij Gustschin + * + * Based on MPC5121E ADS dts. + * Copyright 2008 Freescale Semiconductor Inc. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +/dts-v1/; + +/ { + model = "pdm360ng"; + compatible = "ifm,pdm360ng"; + #address-cells = <1>; + #size-cells = <1>; + interrupt-parent = <&ipic>; + + aliases { + ethernet0 = ð0; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + PowerPC,5121@0 { + device_type = "cpu"; + reg = <0>; + d-cache-line-size = <0x20>; // 32 bytes + i-cache-line-size = <0x20>; // 32 bytes + d-cache-size = <0x8000>; // L1, 32K + i-cache-size = <0x8000>; // L1, 32K + timebase-frequency = <49500000>;// 49.5 MHz (csb/4) + bus-frequency = <198000000>; // 198 MHz csb bus + clock-frequency = <396000000>; // 396 MHz ppc core + }; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x20000000>; // 512MB at 0 + }; + + nfc@40000000 { + compatible = "fsl,mpc5121-nfc"; + reg = <0x40000000 0x100000>; + interrupts = <0x6 0x8>; + #address-cells = <0x1>; + #size-cells = <0x1>; + bank-width = <0x1>; + chips = <0x1>; + + partition@0 { + label = "nand0"; + reg = <0x0 0x40000000>; + }; + }; + + sram@50000000 { + compatible = "fsl,mpc5121-sram"; + reg = <0x50000000 0x20000>; // 128K at 0x50000000 + }; + + localbus@80000020 { + compatible = "fsl,mpc5121-localbus"; + #address-cells = <2>; + #size-cells = <1>; + reg = <0x80000020 0x40>; + + ranges = <0x0 0x0 0xf0000000 0x10000000 /* Flash */ + 0x2 0x0 0x50040000 0x00020000>; /* CS2: MRAM */ + + flash@0,0 { + compatible = "amd,s29gl01gp", "cfi-flash"; + reg = <0 0x00000000 0x08000000 + 0 0x08000000 0x08000000>; + #address-cells = <1>; + #size-cells = <1>; + bank-width = <4>; + device-width = <2>; + + partition@0 { + label = "u-boot"; + reg = <0x00000000 0x00080000>; + read-only; + }; + partition@80000 { + label = "environment"; + reg = <0x00080000 0x00080000>; + read-only; + }; + partition@100000 { + label = "splash-image"; + reg = <0x00100000 0x00080000>; + read-only; + }; + partition@180000 { + label = "device-tree"; + reg = <0x00180000 0x00040000>; + }; + partition@1c0000 { + label = "kernel"; + reg = <0x001c0000 0x00500000>; + }; + partition@6c0000 { + label = "filesystem"; + reg = <0x006c0000 0x07940000>; + }; + }; + + mram0@2,0 { + compatible = "mtd-ram"; + reg = <2 0x00000 0x10000>; + bank-width = <2>; + }; + + mram1@2,10000 { + compatible = "mtd-ram"; + reg = <2 0x010000 0x10000>; + bank-width = <2>; + }; + }; + + soc@80000000 { + compatible = "fsl,mpc5121-immr"; + #address-cells = <1>; + #size-cells = <1>; + #interrupt-cells = <2>; + ranges = <0x0 0x80000000 0x400000>; + reg = <0x80000000 0x400000>; + bus-frequency = <66000000>; // 66 MHz ips bus + + // IPIC + // interrupts cell = + // sense values match linux IORESOURCE_IRQ_* defines: + // sense == 8: Level, low assertion + // sense == 2: Edge, high-to-low change + // + ipic: interrupt-controller@c00 { + compatible = "fsl,mpc5121-ipic", "fsl,ipic"; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <0xc00 0x100>; + }; + + rtc@a00 { // Real time clock + compatible = "fsl,mpc5121-rtc"; + reg = <0xa00 0x100>; + interrupts = <79 0x8 80 0x8>; + }; + + reset@e00 { // Reset module + compatible = "fsl,mpc5121-reset"; + reg = <0xe00 0x100>; + }; + + clock@f00 { // Clock control + compatible = "fsl,mpc5121-clock"; + reg = <0xf00 0x100>; + }; + + pmc@1000{ //Power Management Controller + compatible = "fsl,mpc5121-pmc"; + reg = <0x1000 0x100>; + interrupts = <83 0x2>; + }; + + gpio@1100 { + compatible = "fsl,mpc5121-gpio"; + reg = <0x1100 0x100>; + interrupts = <78 0x8>; + }; + + can@1300 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <12 0x8>; + reg = <0x1300 0x80>; + }; + + can@1380 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <13 0x8>; + reg = <0x1380 0x80>; + }; + + i2c@1700 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5121-i2c"; + reg = <0x1700 0x20>; + interrupts = <0x9 0x8>; + fsl,preserve-clocking; + + eeprom@50 { + compatible = "at,24c01"; + reg = <0x50>; + }; + + rtc@68 { + compatible = "stm,m41t00"; + reg = <0x68>; + }; + }; + + i2c@1740 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5121-i2c"; + reg = <0x1740 0x20>; + interrupts = <0xb 0x8>; + fsl,preserve-clocking; + }; + + i2ccontrol@1760 { + compatible = "fsl,mpc5121-i2c-ctrl"; + reg = <0x1760 0x8>; + }; + + axe@2000 { + compatible = "fsl,mpc5121-axe"; + reg = <0x2000 0x100>; + interrupts = <42 0x8>; + }; + + display@2100 { + compatible = "fsl,mpc5121-diu"; + reg = <0x2100 0x100>; + interrupts = <64 0x8>; + }; + + can@2300 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <90 0x8>; + reg = <0x2300 0x80>; + }; + + can@2380 { + compatible = "fsl,mpc5121-mscan"; + interrupts = <91 0x8>; + reg = <0x2380 0x80>; + }; + + viu@2400 { + compatible = "fsl,mpc5121-viu"; + reg = <0x2400 0x400>; + interrupts = <67 0x8>; + }; + + mdio@2800 { + compatible = "fsl,mpc5121-fec-mdio"; + reg = <0x2800 0x200>; + #address-cells = <1>; + #size-cells = <0>; + phy: ethernet-phy@0 { + compatible = "smsc,lan8700"; + reg = <0x1f>; + }; + }; + + eth0: ethernet@2800 { + compatible = "fsl,mpc5121-fec"; + reg = <0x2800 0x200>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <4 0x8>; + phy-handle = < &phy >; + }; + + // USB1 using external ULPI PHY + usb@3000 { + compatible = "fsl,mpc5121-usb2-dr"; + reg = <0x3000 0x600>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <43 0x8>; + dr_mode = "host"; + phy_type = "ulpi"; + }; + + // USB0 using internal UTMI PHY + usb@4000 { + compatible = "fsl,mpc5121-usb2-dr"; + reg = <0x4000 0x600>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <44 0x8>; + dr_mode = "otg"; + phy_type = "utmi_wide"; + fsl,invert-pwr-fault; + }; + + // IO control + ioctl@a000 { + compatible = "fsl,mpc5121-ioctl"; + reg = <0xA000 0x1000>; + }; + + // 512x PSCs are not 52xx PSCs compatible + serial@11000 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <0>; + reg = <0x11000 0x100>; + interrupts = <40 0x8>; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; + }; + + serial@11100 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <1>; + reg = <0x11100 0x100>; + interrupts = <40 0x8>; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; + }; + + serial@11200 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <2>; + reg = <0x11200 0x100>; + interrupts = <40 0x8>; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; + }; + + serial@11300 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <3>; + reg = <0x11300 0x100>; + interrupts = <40 0x8>; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; + }; + + serial@11400 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <4>; + reg = <0x11400 0x100>; + interrupts = <40 0x8>; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; + }; + + serial@11600 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <6>; + reg = <0x11600 0x100>; + interrupts = <40 0x8>; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; + }; + + serial@11800 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <8>; + reg = <0x11800 0x100>; + interrupts = <40 0x8>; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; + }; + + serial@11B00 { + compatible = "fsl,mpc5121-psc-uart", "fsl,mpc5121-psc"; + cell-index = <11>; + reg = <0x11B00 0x100>; + interrupts = <40 0x8>; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; + }; + + pscfifo@11f00 { + compatible = "fsl,mpc5121-psc-fifo"; + reg = <0x11f00 0x100>; + interrupts = <40 0x8>; + }; + + spi@11900 { + compatible = "fsl,mpc5121-psc-spi", "fsl,mpc5121-psc"; + cell-index = <9>; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x11900 0x100>; + interrupts = <40 0x8>; + fsl,rx-fifo-size = <16>; + fsl,tx-fifo-size = <16>; + + // 7845 touch screen controller + ts@0 { + compatible = "ti,ads7846"; + reg = <0x0>; + spi-max-frequency = <3000000>; + // pen irq is GPIO25 + interrupts = <78 0x8>; + }; + }; + + dma@14000 { + compatible = "fsl,mpc5121-dma"; + reg = <0x14000 0x1800>; + interrupts = <65 0x8>; + }; + }; +}; -- cgit v1.2.1 From dee9ad718b4f0009a4170c178f7171c7b1f06f92 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Tue, 8 Jun 2010 09:55:50 +0000 Subject: powerpc/85xx: Fix booting for P1021MDS boards P1021 processors have no dedicated ROM to store the QE microcode, so the fimrware is stored externally, and it is U-Boot responsibility to load it. It might be that the board is booting without QE, e.g. currently U-Boot doesn't support QE for P1021MDS boards, which means that QE isn't initialized, and so the board hangs early at boot. This patch fixes the issue by marking QE as disabled and checking the state in the probing code. U-Boot should fixup the state if it initialized the QE. Signed-off-by: Anton Vorontsov Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/p1021mds.dts | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/powerpc/boot/dts') diff --git a/arch/powerpc/boot/dts/p1021mds.dts b/arch/powerpc/boot/dts/p1021mds.dts index 7fad2df25981..ad5b85269004 100644 --- a/arch/powerpc/boot/dts/p1021mds.dts +++ b/arch/powerpc/boot/dts/p1021mds.dts @@ -617,6 +617,7 @@ bus-frequency = <0>; fsl,qe-num-riscs = <1>; fsl,qe-num-snums = <28>; + status = "disabled"; /* no firmware loaded */ qeic: interrupt-controller@80 { interrupt-controller; -- cgit v1.2.1 From ba4d1275d1ad89a17cd529f7755e227ead52be4e Mon Sep 17 00:00:00 2001 From: Ilya Yanok Date: Thu, 8 Jul 2010 10:10:39 +0000 Subject: powerpc/mpc8308rdb: support for MPC8308RDB board from Freescale This patch adds support for MPC8308RDB development board from Freescale. Supported devices: DUART Dual Ethernet NOR and NAND flashes I2C USB in peripheral mode PCIE support is broken by the commit 3da34aa ("powerpc/fsl: Support unique MSI addresses per PCIe Root Complex"). Works after revert. Signed-off-by: Ilya Yanok Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mpc8308rdb.dts | 303 +++++++++++++++++++++++++++++++++++ 1 file changed, 303 insertions(+) create mode 100644 arch/powerpc/boot/dts/mpc8308rdb.dts (limited to 'arch/powerpc/boot/dts') diff --git a/arch/powerpc/boot/dts/mpc8308rdb.dts b/arch/powerpc/boot/dts/mpc8308rdb.dts new file mode 100644 index 000000000000..a97eb2db5a18 --- /dev/null +++ b/arch/powerpc/boot/dts/mpc8308rdb.dts @@ -0,0 +1,303 @@ +/* + * MPC8308RDB Device Tree Source + * + * Copyright 2009 Freescale Semiconductor Inc. + * Copyright 2010 Ilya Yanok, Emcraft Systems, yanok@emcraft.com + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +/dts-v1/; + +/ { + compatible = "fsl,mpc8308rdb"; + #address-cells = <1>; + #size-cells = <1>; + + aliases { + ethernet0 = &enet0; + ethernet1 = &enet1; + serial0 = &serial0; + serial1 = &serial1; + pci0 = &pci0; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + PowerPC,8308@0 { + device_type = "cpu"; + reg = <0x0>; + d-cache-line-size = <32>; + i-cache-line-size = <32>; + d-cache-size = <16384>; + i-cache-size = <16384>; + timebase-frequency = <0>; // from bootloader + bus-frequency = <0>; // from bootloader + clock-frequency = <0>; // from bootloader + }; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x08000000>; // 128MB at 0 + }; + + localbus@e0005000 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "fsl,mpc8315-elbc", "fsl,elbc", "simple-bus"; + reg = <0xe0005000 0x1000>; + interrupts = <77 0x8>; + interrupt-parent = <&ipic>; + + // CS0 and CS1 are swapped when + // booting from nand, but the + // addresses are the same. + ranges = <0x0 0x0 0xfe000000 0x00800000 + 0x1 0x0 0xe0600000 0x00002000 + 0x2 0x0 0xf0000000 0x00020000 + 0x3 0x0 0xfa000000 0x00008000>; + + flash@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x0 0x0 0x800000>; + bank-width = <2>; + device-width = <1>; + + u-boot@0 { + reg = <0x0 0x60000>; + read-only; + }; + env@60000 { + reg = <0x60000 0x10000>; + }; + env1@70000 { + reg = <0x70000 0x10000>; + }; + kernel@80000 { + reg = <0x80000 0x200000>; + }; + dtb@280000 { + reg = <0x280000 0x10000>; + }; + ramdisk@290000 { + reg = <0x290000 0x570000>; + }; + }; + + nand@1,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8315-fcm-nand", + "fsl,elbc-fcm-nand"; + reg = <0x1 0x0 0x2000>; + + jffs2@0 { + reg = <0x0 0x2000000>; + }; + }; + }; + + immr@e0000000 { + #address-cells = <1>; + #size-cells = <1>; + device_type = "soc"; + compatible = "fsl,mpc8315-immr", "simple-bus"; + ranges = <0 0xe0000000 0x00100000>; + reg = <0xe0000000 0x00000200>; + bus-frequency = <0>; + + i2c@3000 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + compatible = "fsl-i2c"; + reg = <0x3000 0x100>; + interrupts = <14 0x8>; + interrupt-parent = <&ipic>; + dfsrr; + rtc@68 { + compatible = "dallas,ds1339"; + reg = <0x68>; + }; + }; + + usb@23000 { + compatible = "fsl-usb2-dr"; + reg = <0x23000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <&ipic>; + interrupts = <38 0x8>; + dr_mode = "peripheral"; + phy_type = "ulpi"; + }; + + enet0: ethernet@24000 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x24000 0x1000>; + + cell-index = <0>; + device_type = "network"; + model = "eTSEC"; + compatible = "gianfar"; + reg = <0x24000 0x1000>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <32 0x8 33 0x8 34 0x8>; + interrupt-parent = <&ipic>; + tbi-handle = < &tbi0 >; + phy-handle = < &phy2 >; + fsl,magic-packet; + + mdio@520 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,gianfar-mdio"; + reg = <0x520 0x20>; + phy2: ethernet-phy@2 { + interrupt-parent = <&ipic>; + interrupts = <17 0x8>; + reg = <0x2>; + device_type = "ethernet-phy"; + }; + tbi0: tbi-phy@11 { + reg = <0x11>; + device_type = "tbi-phy"; + }; + }; + }; + + enet1: ethernet@25000 { + #address-cells = <1>; + #size-cells = <1>; + cell-index = <1>; + device_type = "network"; + model = "eTSEC"; + compatible = "gianfar"; + reg = <0x25000 0x1000>; + ranges = <0x0 0x25000 0x1000>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <35 0x8 36 0x8 37 0x8>; + interrupt-parent = <&ipic>; + tbi-handle = < &tbi1 >; + /* Vitesse 7385 isn't on the MDIO bus */ + fixed-link = <1 1 1000 0 0>; + fsl,magic-packet; + + mdio@520 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,gianfar-tbi"; + reg = <0x520 0x20>; + + tbi1: tbi-phy@11 { + reg = <0x11>; + device_type = "tbi-phy"; + }; + }; + }; + + serial0: serial@4500 { + cell-index = <0>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x4500 0x100>; + clock-frequency = <133333333>; + interrupts = <9 0x8>; + interrupt-parent = <&ipic>; + }; + + serial1: serial@4600 { + cell-index = <1>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x4600 0x100>; + clock-frequency = <133333333>; + interrupts = <10 0x8>; + interrupt-parent = <&ipic>; + }; + + gpio@c00 { + #gpio-cells = <2>; + device_type = "gpio"; + compatible = "fsl,mpc8308-gpio", "fsl,mpc8349-gpio"; + reg = <0xc00 0x18>; + interrupts = <74 0x8>; + interrupt-parent = <&ipic>; + gpio-controller; + }; + + /* IPIC + * interrupts cell = + * sense values match linux IORESOURCE_IRQ_* defines: + * sense == 8: Level, low assertion + * sense == 2: Edge, high-to-low change + */ + ipic: interrupt-controller@700 { + compatible = "fsl,ipic"; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <0x700 0x100>; + device_type = "ipic"; + }; + + ipic-msi@7c0 { + compatible = "fsl,ipic-msi"; + reg = <0x7c0 0x40>; + msi-available-ranges = <0x0 0x100>; + interrupts = < 0x43 0x8 + 0x4 0x8 + 0x51 0x8 + 0x52 0x8 + 0x56 0x8 + 0x57 0x8 + 0x58 0x8 + 0x59 0x8 >; + interrupt-parent = < &ipic >; + }; + + }; + + pci0: pcie@e0009000 { + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + device_type = "pci"; + compatible = "fsl,mpc8308-pcie", "fsl,mpc8314-pcie"; + reg = <0xe0009000 0x00001000 + 0xb0000000 0x01000000>; + ranges = <0x02000000 0 0xa0000000 0xa0000000 0 0x10000000 + 0x01000000 0 0x00000000 0xb1000000 0 0x00800000>; + bus-range = <0 0>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = <0 0 0 1 &ipic 1 8 + 0 0 0 2 &ipic 1 8 + 0 0 0 3 &ipic 1 8 + 0 0 0 4 &ipic 1 8>; + interrupts = <0x1 0x8>; + interrupt-parent = <&ipic>; + clock-frequency = <0>; + + pcie@0 { + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + reg = <0 0 0 0 0>; + ranges = <0x02000000 0 0xa0000000 + 0x02000000 0 0xa0000000 + 0 0x10000000 + 0x01000000 0 0x00000000 + 0x01000000 0 0x00000000 + 0 0x00800000>; + }; + }; +}; -- cgit v1.2.1 From 07c638398f490e63275ae23aa51b7c50df7d1a49 Mon Sep 17 00:00:00 2001 From: Dmitry Eremin-Solenikov Date: Wed, 21 Jul 2010 10:33:23 +0000 Subject: powerpc/tqm85xx: update PCI interrupt-map attribute Update PCI IRQ mapping on TQM85xx platforms: include INTC and INTD on PCI-X slot and add INTA/INTB mapping for PCMCIA bridge. Signed-off-by: Dmitry Eremin-Solenikov Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/tqm8540.dts | 9 ++++++++- arch/powerpc/boot/dts/tqm8541.dts | 9 ++++++++- arch/powerpc/boot/dts/tqm8548-bigflash.dts | 9 ++++++++- arch/powerpc/boot/dts/tqm8548.dts | 9 ++++++++- arch/powerpc/boot/dts/tqm8555.dts | 9 ++++++++- arch/powerpc/boot/dts/tqm8560.dts | 9 ++++++++- 6 files changed, 48 insertions(+), 6 deletions(-) (limited to 'arch/powerpc/boot/dts') diff --git a/arch/powerpc/boot/dts/tqm8540.dts b/arch/powerpc/boot/dts/tqm8540.dts index 71347537b83e..15ca731bc24e 100644 --- a/arch/powerpc/boot/dts/tqm8540.dts +++ b/arch/powerpc/boot/dts/tqm8540.dts @@ -289,7 +289,14 @@ interrupt-map = < /* IDSEL 28 */ 0xe000 0 0 1 &mpic 2 1 - 0xe000 0 0 2 &mpic 3 1>; + 0xe000 0 0 2 &mpic 3 1 + 0xe000 0 0 3 &mpic 6 1 + 0xe000 0 0 4 &mpic 5 1 + + /* IDSEL 11 */ + 0x5800 0 0 1 &mpic 6 1 + 0x5800 0 0 2 &mpic 5 1 + >; interrupt-parent = <&mpic>; interrupts = <24 2>; diff --git a/arch/powerpc/boot/dts/tqm8541.dts b/arch/powerpc/boot/dts/tqm8541.dts index b30f63753d41..f49d09181312 100644 --- a/arch/powerpc/boot/dts/tqm8541.dts +++ b/arch/powerpc/boot/dts/tqm8541.dts @@ -311,7 +311,14 @@ interrupt-map = < /* IDSEL 28 */ 0xe000 0 0 1 &mpic 2 1 - 0xe000 0 0 2 &mpic 3 1>; + 0xe000 0 0 2 &mpic 3 1 + 0xe000 0 0 3 &mpic 6 1 + 0xe000 0 0 4 &mpic 5 1 + + /* IDSEL 11 */ + 0x5800 0 0 1 &mpic 6 1 + 0x5800 0 0 2 &mpic 5 1 + >; interrupt-parent = <&mpic>; interrupts = <24 2>; diff --git a/arch/powerpc/boot/dts/tqm8548-bigflash.dts b/arch/powerpc/boot/dts/tqm8548-bigflash.dts index 61f25e15fd66..5dbb36edb038 100644 --- a/arch/powerpc/boot/dts/tqm8548-bigflash.dts +++ b/arch/powerpc/boot/dts/tqm8548-bigflash.dts @@ -442,7 +442,14 @@ interrupt-map = < /* IDSEL 28 */ 0xe000 0 0 1 &mpic 2 1 - 0xe000 0 0 2 &mpic 3 1>; + 0xe000 0 0 2 &mpic 3 1 + 0xe000 0 0 3 &mpic 6 1 + 0xe000 0 0 4 &mpic 5 1 + + /* IDSEL 11 */ + 0x5800 0 0 1 &mpic 6 1 + 0x5800 0 0 2 &mpic 5 1 + >; interrupt-parent = <&mpic>; interrupts = <24 2>; diff --git a/arch/powerpc/boot/dts/tqm8548.dts b/arch/powerpc/boot/dts/tqm8548.dts index 025759c7c955..a050ae427108 100644 --- a/arch/powerpc/boot/dts/tqm8548.dts +++ b/arch/powerpc/boot/dts/tqm8548.dts @@ -442,7 +442,14 @@ interrupt-map = < /* IDSEL 28 */ 0xe000 0 0 1 &mpic 2 1 - 0xe000 0 0 2 &mpic 3 1>; + 0xe000 0 0 2 &mpic 3 1 + 0xe000 0 0 3 &mpic 6 1 + 0xe000 0 0 4 &mpic 5 1 + + /* IDSEL 11 */ + 0x5800 0 0 1 &mpic 6 1 + 0x5800 0 0 2 &mpic 5 1 + >; interrupt-parent = <&mpic>; interrupts = <24 2>; diff --git a/arch/powerpc/boot/dts/tqm8555.dts b/arch/powerpc/boot/dts/tqm8555.dts index 95e287381836..81bad8cd3756 100644 --- a/arch/powerpc/boot/dts/tqm8555.dts +++ b/arch/powerpc/boot/dts/tqm8555.dts @@ -311,7 +311,14 @@ interrupt-map = < /* IDSEL 28 */ 0xe000 0 0 1 &mpic 2 1 - 0xe000 0 0 2 &mpic 3 1>; + 0xe000 0 0 2 &mpic 3 1 + 0xe000 0 0 3 &mpic 6 1 + 0xe000 0 0 4 &mpic 5 1 + + /* IDSEL 11 */ + 0x5800 0 0 1 &mpic 6 1 + 0x5800 0 0 2 &mpic 5 1 + >; interrupt-parent = <&mpic>; interrupts = <24 2>; diff --git a/arch/powerpc/boot/dts/tqm8560.dts b/arch/powerpc/boot/dts/tqm8560.dts index ff70580a8f4c..22ec39b5beeb 100644 --- a/arch/powerpc/boot/dts/tqm8560.dts +++ b/arch/powerpc/boot/dts/tqm8560.dts @@ -382,7 +382,14 @@ interrupt-map = < /* IDSEL 28 */ 0xe000 0 0 1 &mpic 2 1 - 0xe000 0 0 2 &mpic 3 1>; + 0xe000 0 0 2 &mpic 3 1 + 0xe000 0 0 3 &mpic 6 1 + 0xe000 0 0 4 &mpic 5 1 + + /* IDSEL 11 */ + 0x5800 0 0 1 &mpic 6 1 + 0x5800 0 0 2 &mpic 5 1 + >; interrupt-parent = <&mpic>; interrupts = <24 2>; -- cgit v1.2.1 From 8a4ab218ef7034660982931b3e1eb6bbc2bde0ea Mon Sep 17 00:00:00 2001 From: Bradley Hughes Date: Wed, 21 Jul 2010 12:04:06 +0000 Subject: powerpc/85xx: Change deprecated binding for 85xx-based boards The "fsl,85..." style compatible binding was to be deprecated some time ago. This patch corrects existing occurrences of the incorrect binding. The memory-controller and l2-cache-controller are the only affected nodes. Signed-off-by: Bradley Hughes Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/mpc8540ads.dts | 4 ++-- arch/powerpc/boot/dts/mpc8541cds.dts | 4 ++-- arch/powerpc/boot/dts/mpc8544ds.dts | 4 ++-- arch/powerpc/boot/dts/mpc8548cds.dts | 4 ++-- arch/powerpc/boot/dts/mpc8555cds.dts | 4 ++-- arch/powerpc/boot/dts/mpc8560ads.dts | 4 ++-- arch/powerpc/boot/dts/mpc8568mds.dts | 4 ++-- 7 files changed, 14 insertions(+), 14 deletions(-) (limited to 'arch/powerpc/boot/dts') diff --git a/arch/powerpc/boot/dts/mpc8540ads.dts b/arch/powerpc/boot/dts/mpc8540ads.dts index 9dc292962a9a..8d1bf0fd9268 100644 --- a/arch/powerpc/boot/dts/mpc8540ads.dts +++ b/arch/powerpc/boot/dts/mpc8540ads.dts @@ -71,14 +71,14 @@ }; memory-controller@2000 { - compatible = "fsl,8540-memory-controller"; + compatible = "fsl,mpc8540-memory-controller"; reg = <0x2000 0x1000>; interrupt-parent = <&mpic>; interrupts = <18 2>; }; L2: l2-cache-controller@20000 { - compatible = "fsl,8540-l2-cache-controller"; + compatible = "fsl,mpc8540-l2-cache-controller"; reg = <0x20000 0x1000>; cache-line-size = <32>; // 32 bytes cache-size = <0x40000>; // L2, 256K diff --git a/arch/powerpc/boot/dts/mpc8541cds.dts b/arch/powerpc/boot/dts/mpc8541cds.dts index 9a3ad311aedf..87ff96549fac 100644 --- a/arch/powerpc/boot/dts/mpc8541cds.dts +++ b/arch/powerpc/boot/dts/mpc8541cds.dts @@ -71,14 +71,14 @@ }; memory-controller@2000 { - compatible = "fsl,8541-memory-controller"; + compatible = "fsl,mpc8541-memory-controller"; reg = <0x2000 0x1000>; interrupt-parent = <&mpic>; interrupts = <18 2>; }; L2: l2-cache-controller@20000 { - compatible = "fsl,8541-l2-cache-controller"; + compatible = "fsl,mpc8541-l2-cache-controller"; reg = <0x20000 0x1000>; cache-line-size = <32>; // 32 bytes cache-size = <0x40000>; // L2, 256K diff --git a/arch/powerpc/boot/dts/mpc8544ds.dts b/arch/powerpc/boot/dts/mpc8544ds.dts index 98e94b465662..d793968743c9 100644 --- a/arch/powerpc/boot/dts/mpc8544ds.dts +++ b/arch/powerpc/boot/dts/mpc8544ds.dts @@ -73,14 +73,14 @@ }; memory-controller@2000 { - compatible = "fsl,8544-memory-controller"; + compatible = "fsl,mpc8544-memory-controller"; reg = <0x2000 0x1000>; interrupt-parent = <&mpic>; interrupts = <18 2>; }; L2: l2-cache-controller@20000 { - compatible = "fsl,8544-l2-cache-controller"; + compatible = "fsl,mpc8544-l2-cache-controller"; reg = <0x20000 0x1000>; cache-line-size = <32>; // 32 bytes cache-size = <0x40000>; // L2, 256K diff --git a/arch/powerpc/boot/dts/mpc8548cds.dts b/arch/powerpc/boot/dts/mpc8548cds.dts index 0f5262452682..a17a5572fb73 100644 --- a/arch/powerpc/boot/dts/mpc8548cds.dts +++ b/arch/powerpc/boot/dts/mpc8548cds.dts @@ -74,14 +74,14 @@ }; memory-controller@2000 { - compatible = "fsl,8548-memory-controller"; + compatible = "fsl,mpc8548-memory-controller"; reg = <0x2000 0x1000>; interrupt-parent = <&mpic>; interrupts = <18 2>; }; L2: l2-cache-controller@20000 { - compatible = "fsl,8548-l2-cache-controller"; + compatible = "fsl,mpc8548-l2-cache-controller"; reg = <0x20000 0x1000>; cache-line-size = <32>; // 32 bytes cache-size = <0x80000>; // L2, 512K diff --git a/arch/powerpc/boot/dts/mpc8555cds.dts b/arch/powerpc/boot/dts/mpc8555cds.dts index 065b2f093de2..5c5614f9eb17 100644 --- a/arch/powerpc/boot/dts/mpc8555cds.dts +++ b/arch/powerpc/boot/dts/mpc8555cds.dts @@ -71,14 +71,14 @@ }; memory-controller@2000 { - compatible = "fsl,8555-memory-controller"; + compatible = "fsl,mpc8555-memory-controller"; reg = <0x2000 0x1000>; interrupt-parent = <&mpic>; interrupts = <18 2>; }; L2: l2-cache-controller@20000 { - compatible = "fsl,8555-l2-cache-controller"; + compatible = "fsl,mpc8555-l2-cache-controller"; reg = <0x20000 0x1000>; cache-line-size = <32>; // 32 bytes cache-size = <0x40000>; // L2, 256K diff --git a/arch/powerpc/boot/dts/mpc8560ads.dts b/arch/powerpc/boot/dts/mpc8560ads.dts index a5bb1ec70a5a..6e85e1ba0851 100644 --- a/arch/powerpc/boot/dts/mpc8560ads.dts +++ b/arch/powerpc/boot/dts/mpc8560ads.dts @@ -71,14 +71,14 @@ }; memory-controller@2000 { - compatible = "fsl,8540-memory-controller"; + compatible = "fsl,mpc8540-memory-controller"; reg = <0x2000 0x1000>; interrupt-parent = <&mpic>; interrupts = <18 2>; }; L2: l2-cache-controller@20000 { - compatible = "fsl,8540-l2-cache-controller"; + compatible = "fsl,mpc8540-l2-cache-controller"; reg = <0x20000 0x1000>; cache-line-size = <32>; // 32 bytes cache-size = <0x40000>; // L2, 256K diff --git a/arch/powerpc/boot/dts/mpc8568mds.dts b/arch/powerpc/boot/dts/mpc8568mds.dts index 92fb17876e7d..30cf0e098bb9 100644 --- a/arch/powerpc/boot/dts/mpc8568mds.dts +++ b/arch/powerpc/boot/dts/mpc8568mds.dts @@ -124,14 +124,14 @@ }; memory-controller@2000 { - compatible = "fsl,8568-memory-controller"; + compatible = "fsl,mpc8568-memory-controller"; reg = <0x2000 0x1000>; interrupt-parent = <&mpic>; interrupts = <18 2>; }; L2: l2-cache-controller@20000 { - compatible = "fsl,8568-l2-cache-controller"; + compatible = "fsl,mpc8568-l2-cache-controller"; reg = <0x20000 0x1000>; cache-line-size = <32>; // 32 bytes cache-size = <0x80000>; // L2, 512K -- cgit v1.2.1 From 51974d3162308695f888600b15c6f6009069dd0d Mon Sep 17 00:00:00 2001 From: Bradley Hughes Date: Wed, 21 Jul 2010 12:04:00 +0000 Subject: powerpc/85xx: Adding DTS for the STx GP3-SSA MPC8555 board This version uses "fsl,mpc8555..." instead of "fsl,85..." notation. There is also an 8541 version of this board so DTS for this board is specific to the 8555 processor. Another patch is coming to fix-up other DTS that use old notation. Signed-off-by: Bradley Hughes Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/stxssa8555.dts | 380 +++++++++++++++++++++++++++++++++++ 1 file changed, 380 insertions(+) create mode 100644 arch/powerpc/boot/dts/stxssa8555.dts (limited to 'arch/powerpc/boot/dts') diff --git a/arch/powerpc/boot/dts/stxssa8555.dts b/arch/powerpc/boot/dts/stxssa8555.dts new file mode 100644 index 000000000000..49efd44057d7 --- /dev/null +++ b/arch/powerpc/boot/dts/stxssa8555.dts @@ -0,0 +1,380 @@ +/* + * MPC8555-based STx GP3 Device Tree Source + * + * Copyright 2006, 2008 Freescale Semiconductor Inc. + * + * Copyright 2010 Silicon Turnkey Express LLC. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +/dts-v1/; + +/ { + model = "stx,gp3"; + compatible = "stx,gp3-8560", "stx,gp3"; + #address-cells = <1>; + #size-cells = <1>; + + aliases { + ethernet0 = &enet0; + ethernet1 = &enet1; + serial0 = &serial0; + serial1 = &serial1; + pci0 = &pci0; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + PowerPC,8555@0 { + device_type = "cpu"; + reg = <0x0>; + d-cache-line-size = <32>; // 32 bytes + i-cache-line-size = <32>; // 32 bytes + d-cache-size = <0x8000>; // L1, 32K + i-cache-size = <0x8000>; // L1, 32K + timebase-frequency = <0>; // 33 MHz, from uboot + bus-frequency = <0>; // 166 MHz + clock-frequency = <0>; // 825 MHz, from uboot + next-level-cache = <&L2>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x10000000>; + }; + + soc8555@e0000000 { + #address-cells = <1>; + #size-cells = <1>; + device_type = "soc"; + compatible = "simple-bus"; + ranges = <0x0 0xe0000000 0x100000>; + bus-frequency = <0>; + + ecm-law@0 { + compatible = "fsl,ecm-law"; + reg = <0x0 0x1000>; + fsl,num-laws = <8>; + }; + + ecm@1000 { + compatible = "fsl,mpc8555-ecm", "fsl,ecm"; + reg = <0x1000 0x1000>; + interrupts = <17 2>; + interrupt-parent = <&mpic>; + }; + + memory-controller@2000 { + compatible = "fsl,mpc8555-memory-controller"; + reg = <0x2000 0x1000>; + interrupt-parent = <&mpic>; + interrupts = <18 2>; + }; + + L2: l2-cache-controller@20000 { + compatible = "fsl,mpc8555-l2-cache-controller"; + reg = <0x20000 0x1000>; + cache-line-size = <32>; // 32 bytes + cache-size = <0x40000>; // L2, 256K + interrupt-parent = <&mpic>; + interrupts = <16 2>; + }; + + i2c@3000 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + compatible = "fsl-i2c"; + reg = <0x3000 0x100>; + interrupts = <43 2>; + interrupt-parent = <&mpic>; + dfsrr; + }; + + dma@21300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8555-dma", "fsl,eloplus-dma"; + reg = <0x21300 0x4>; + ranges = <0x0 0x21100 0x200>; + cell-index = <0>; + dma-channel@0 { + compatible = "fsl,mpc8555-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x0 0x80>; + cell-index = <0>; + interrupt-parent = <&mpic>; + interrupts = <20 2>; + }; + dma-channel@80 { + compatible = "fsl,mpc8555-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + cell-index = <1>; + interrupt-parent = <&mpic>; + interrupts = <21 2>; + }; + dma-channel@100 { + compatible = "fsl,mpc8555-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + cell-index = <2>; + interrupt-parent = <&mpic>; + interrupts = <22 2>; + }; + dma-channel@180 { + compatible = "fsl,mpc8555-dma-channel", + "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + cell-index = <3>; + interrupt-parent = <&mpic>; + interrupts = <23 2>; + }; + }; + + enet0: ethernet@24000 { + #address-cells = <1>; + #size-cells = <1>; + cell-index = <0>; + device_type = "network"; + model = "TSEC"; + compatible = "gianfar"; + reg = <0x24000 0x1000>; + ranges = <0x0 0x24000 0x1000>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <29 2 30 2 34 2>; + interrupt-parent = <&mpic>; + tbi-handle = <&tbi0>; + phy-handle = <&phy0>; + + mdio@520 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,gianfar-mdio"; + reg = <0x520 0x20>; + + phy0: ethernet-phy@2 { + interrupt-parent = <&mpic>; + interrupts = <5 1>; + reg = <0x2>; + device_type = "ethernet-phy"; + }; + phy1: ethernet-phy@4 { + interrupt-parent = <&mpic>; + interrupts = <5 1>; + reg = <0x4>; + device_type = "ethernet-phy"; + }; + tbi0: tbi-phy@11 { + reg = <0x11>; + device_type = "tbi-phy"; + }; + }; + }; + + enet1: ethernet@25000 { + #address-cells = <1>; + #size-cells = <1>; + cell-index = <1>; + device_type = "network"; + model = "TSEC"; + compatible = "gianfar"; + reg = <0x25000 0x1000>; + ranges = <0x0 0x25000 0x1000>; + local-mac-address = [ 00 00 00 00 00 00 ]; + interrupts = <35 2 36 2 40 2>; + interrupt-parent = <&mpic>; + tbi-handle = <&tbi1>; + phy-handle = <&phy1>; + + mdio@520 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,gianfar-tbi"; + reg = <0x520 0x20>; + + tbi1: tbi-phy@11 { + reg = <0x11>; + device_type = "tbi-phy"; + }; + }; + }; + + serial0: serial@4500 { + cell-index = <0>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x4500 0x100>; // reg base, size + clock-frequency = <0>; // should we fill in in uboot? + interrupts = <42 2>; + interrupt-parent = <&mpic>; + }; + + serial1: serial@4600 { + cell-index = <1>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x4600 0x100>; // reg base, size + clock-frequency = <0>; // should we fill in in uboot? + interrupts = <42 2>; + interrupt-parent = <&mpic>; + }; + + crypto@30000 { + compatible = "fsl,sec2.0"; + reg = <0x30000 0x10000>; + interrupts = <45 2>; + interrupt-parent = <&mpic>; + fsl,num-channels = <4>; + fsl,channel-fifo-len = <24>; + fsl,exec-units-mask = <0x7e>; + fsl,descriptor-types-mask = <0x01010ebf>; + }; + + mpic: pic@40000 { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <0x40000 0x40000>; + compatible = "chrp,open-pic"; + device_type = "open-pic"; + }; + + cpm@919c0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc8555-cpm", "fsl,cpm2"; + reg = <0x919c0 0x30>; + ranges; + + muram@80000 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x80000 0x10000>; + + data@0 { + compatible = "fsl,cpm-muram-data"; + reg = <0x0 0x2000 0x9000 0x1000>; + }; + }; + + brg@919f0 { + compatible = "fsl,mpc8555-brg", + "fsl,cpm2-brg", + "fsl,cpm-brg"; + reg = <0x919f0 0x10 0x915f0 0x10>; + }; + + cpmpic: pic@90c00 { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + interrupts = <46 2>; + interrupt-parent = <&mpic>; + reg = <0x90c00 0x80>; + compatible = "fsl,mpc8555-cpm-pic", "fsl,cpm2-pic"; + }; + }; + }; + + pci0: pci@e0008000 { + interrupt-map-mask = <0x1f800 0x0 0x0 0x7>; + interrupt-map = < + + /* IDSEL 0x10 */ + 0x8000 0x0 0x0 0x1 &mpic 0x0 0x1 + 0x8000 0x0 0x0 0x2 &mpic 0x1 0x1 + 0x8000 0x0 0x0 0x3 &mpic 0x2 0x1 + 0x8000 0x0 0x0 0x4 &mpic 0x3 0x1 + + /* IDSEL 0x11 */ + 0x8800 0x0 0x0 0x1 &mpic 0x0 0x1 + 0x8800 0x0 0x0 0x2 &mpic 0x1 0x1 + 0x8800 0x0 0x0 0x3 &mpic 0x2 0x1 + 0x8800 0x0 0x0 0x4 &mpic 0x3 0x1 + + /* IDSEL 0x12 (Slot 1) */ + 0x9000 0x0 0x0 0x1 &mpic 0x0 0x1 + 0x9000 0x0 0x0 0x2 &mpic 0x1 0x1 + 0x9000 0x0 0x0 0x3 &mpic 0x2 0x1 + 0x9000 0x0 0x0 0x4 &mpic 0x3 0x1 + + /* IDSEL 0x13 (Slot 2) */ + 0x9800 0x0 0x0 0x1 &mpic 0x1 0x1 + 0x9800 0x0 0x0 0x2 &mpic 0x2 0x1 + 0x9800 0x0 0x0 0x3 &mpic 0x3 0x1 + 0x9800 0x0 0x0 0x4 &mpic 0x0 0x1 + + /* IDSEL 0x14 (Slot 3) */ + 0xa000 0x0 0x0 0x1 &mpic 0x2 0x1 + 0xa000 0x0 0x0 0x2 &mpic 0x3 0x1 + 0xa000 0x0 0x0 0x3 &mpic 0x0 0x1 + 0xa000 0x0 0x0 0x4 &mpic 0x1 0x1 + + /* IDSEL 0x15 (Slot 4) */ + 0xa800 0x0 0x0 0x1 &mpic 0x3 0x1 + 0xa800 0x0 0x0 0x2 &mpic 0x0 0x1 + 0xa800 0x0 0x0 0x3 &mpic 0x1 0x1 + 0xa800 0x0 0x0 0x4 &mpic 0x2 0x1 + + /* Bus 1 (Tundra Bridge) */ + /* IDSEL 0x12 (ISA bridge) */ + 0x19000 0x0 0x0 0x1 &mpic 0x0 0x1 + 0x19000 0x0 0x0 0x2 &mpic 0x1 0x1 + 0x19000 0x0 0x0 0x3 &mpic 0x2 0x1 + 0x19000 0x0 0x0 0x4 &mpic 0x3 0x1>; + interrupt-parent = <&mpic>; + interrupts = <24 2>; + bus-range = <0 0>; + ranges = <0x2000000 0x0 0x80000000 0x80000000 0x0 0x20000000 + 0x1000000 0x0 0x0 0xe2000000 0x0 0x100000>; + clock-frequency = <66666666>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0xe0008000 0x1000>; + compatible = "fsl,mpc8540-pci"; + device_type = "pci"; + + i8259@19000 { + interrupt-controller; + device_type = "interrupt-controller"; + reg = <0x19000 0x0 0x0 0x0 0x1>; + #address-cells = <0>; + #interrupt-cells = <2>; + compatible = "chrp,iic"; + interrupts = <1>; + interrupt-parent = <&pci0>; + }; + }; + + pci1: pci@e0009000 { + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; + interrupt-map = < + + /* IDSEL 0x15 */ + 0xa800 0x0 0x0 0x1 &mpic 0xb 0x1 + 0xa800 0x0 0x0 0x2 &mpic 0xb 0x1 + 0xa800 0x0 0x0 0x3 &mpic 0xb 0x1 + 0xa800 0x0 0x0 0x4 &mpic 0xb 0x1>; + interrupt-parent = <&mpic>; + interrupts = <25 2>; + bus-range = <0 0>; + ranges = <0x2000000 0x0 0xa0000000 0xa0000000 0x0 0x20000000 + 0x1000000 0x0 0x0 0xe3000000 0x0 0x100000>; + clock-frequency = <66666666>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0xe0009000 0x1000>; + compatible = "fsl,mpc8540-pci"; + device_type = "pci"; + }; +}; -- cgit v1.2.1 From 30be4c965c37418606006940f45919694693e3f9 Mon Sep 17 00:00:00 2001 From: Timur Tabi Date: Fri, 2 Jul 2010 17:25:03 -0500 Subject: powerpc/85xx: Introduce support for the Freescale P1022DS reference board Introduce basic support for the Freescale P1022DS reference board, based on the Freescale BSP for this board. This patch excludes the DIU, SSI, and MMC/SD drivers. Only a 36-bit DTS is provided. Update mpc86xx_smp_defconfig and mpc85xx_defconfig to support the P1022DS. This means enabling 64-bit physical address support, increasing the maximum zone order to 12 (to allow the DIU driver to allocate large chunks), and clean up the audio options to disable the deprecated OSS support. Signed-off-by: Timur Tabi Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/p1022ds.dts | 633 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 633 insertions(+) create mode 100644 arch/powerpc/boot/dts/p1022ds.dts (limited to 'arch/powerpc/boot/dts') diff --git a/arch/powerpc/boot/dts/p1022ds.dts b/arch/powerpc/boot/dts/p1022ds.dts new file mode 100644 index 000000000000..8bcb10b92677 --- /dev/null +++ b/arch/powerpc/boot/dts/p1022ds.dts @@ -0,0 +1,633 @@ +/* + * P1022 DS 36Bit Physical Address Map Device Tree Source + * + * Copyright 2010 Freescale Semiconductor, Inc. + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +/dts-v1/; +/ { + model = "fsl,P1022"; + compatible = "fsl,P1022DS"; + #address-cells = <2>; + #size-cells = <2>; + interrupt-parent = <&mpic>; + + aliases { + ethernet0 = &enet0; + ethernet1 = &enet1; + serial0 = &serial0; + serial1 = &serial1; + pci0 = &pci0; + pci1 = &pci1; + pci2 = &pci2; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + PowerPC,P1022@0 { + device_type = "cpu"; + reg = <0x0>; + next-level-cache = <&L2>; + }; + + PowerPC,P1022@1 { + device_type = "cpu"; + reg = <0x1>; + next-level-cache = <&L2>; + }; + }; + + memory { + device_type = "memory"; + }; + + localbus@fffe05000 { + #address-cells = <2>; + #size-cells = <1>; + compatible = "fsl,p1022-elbc", "fsl,elbc", "simple-bus"; + reg = <0 0xffe05000 0 0x1000>; + interrupts = <19 2>; + + ranges = <0x0 0x0 0xf 0xe8000000 0x08000000 + 0x1 0x0 0xf 0xe0000000 0x08000000 + 0x2 0x0 0x0 0xffa00000 0x00040000 + 0x3 0x0 0xf 0xffdf0000 0x00008000>; + + nor@0,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x0 0x0 0x8000000>; + bank-width = <2>; + device-width = <1>; + + partition@0 { + reg = <0x0 0x03000000>; + label = "ramdisk-nor"; + read-only; + }; + + partition@3000000 { + reg = <0x03000000 0x00e00000>; + label = "diagnostic-nor"; + read-only; + }; + + partition@3e00000 { + reg = <0x03e00000 0x00200000>; + label = "dink-nor"; + read-only; + }; + + partition@4000000 { + reg = <0x04000000 0x00400000>; + label = "kernel-nor"; + read-only; + }; + + partition@4400000 { + reg = <0x04400000 0x03b00000>; + label = "jffs2-nor"; + }; + + partition@7f00000 { + reg = <0x07f00000 0x00080000>; + label = "dtb-nor"; + read-only; + }; + + partition@7f80000 { + reg = <0x07f80000 0x00080000>; + label = "u-boot-nor"; + read-only; + }; + }; + + nand@2,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,elbc-fcm-nand"; + reg = <0x2 0x0 0x40000>; + + partition@0 { + reg = <0x0 0x02000000>; + label = "u-boot-nand"; + read-only; + }; + + partition@2000000 { + reg = <0x02000000 0x10000000>; + label = "jffs2-nand"; + }; + + partition@12000000 { + reg = <0x12000000 0x10000000>; + label = "ramdisk-nand"; + read-only; + }; + + partition@22000000 { + reg = <0x22000000 0x04000000>; + label = "kernel-nand"; + }; + + partition@26000000 { + reg = <0x26000000 0x01000000>; + label = "dtb-nand"; + read-only; + }; + + partition@27000000 { + reg = <0x27000000 0x19000000>; + label = "reserved-nand"; + }; + }; + }; + + soc@fffe00000 { + #address-cells = <1>; + #size-cells = <1>; + device_type = "soc"; + compatible = "fsl,p1022-immr", "simple-bus"; + ranges = <0x0 0xf 0xffe00000 0x100000>; + bus-frequency = <0>; // Filled out by uboot. + + ecm-law@0 { + compatible = "fsl,ecm-law"; + reg = <0x0 0x1000>; + fsl,num-laws = <12>; + }; + + ecm@1000 { + compatible = "fsl,p1022-ecm", "fsl,ecm"; + reg = <0x1000 0x1000>; + interrupts = <16 2>; + }; + + memory-controller@2000 { + compatible = "fsl,p1022-memory-controller"; + reg = <0x2000 0x1000>; + interrupts = <16 2>; + }; + + i2c@3000 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + compatible = "fsl-i2c"; + reg = <0x3000 0x100>; + interrupts = <43 2>; + dfsrr; + }; + + i2c@3100 { + #address-cells = <1>; + #size-cells = <0>; + cell-index = <1>; + compatible = "fsl-i2c"; + reg = <0x3100 0x100>; + interrupts = <43 2>; + dfsrr; + + wm8776:codec@1a { + compatible = "wlf,wm8776"; + reg = <0x1a>; + /* MCLK source is a stand-alone oscillator */ + clock-frequency = <12288000>; + }; + }; + + serial0: serial@4500 { + cell-index = <0>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x4500 0x100>; + clock-frequency = <0>; + interrupts = <42 2>; + }; + + serial1: serial@4600 { + cell-index = <1>; + device_type = "serial"; + compatible = "ns16550"; + reg = <0x4600 0x100>; + clock-frequency = <0>; + interrupts = <42 2>; + }; + + spi@7000 { + cell-index = <0>; + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,espi"; + reg = <0x7000 0x1000>; + interrupts = <59 0x2>; + espi,num-ss-bits = <4>; + mode = "cpu"; + + fsl_m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,espi-flash"; + reg = <0>; + linux,modalias = "fsl_m25p80"; + spi-max-frequency = <40000000>; /* input clock */ + partition@0 { + label = "u-boot-spi"; + reg = <0x00000000 0x00100000>; + read-only; + }; + partition@100000 { + label = "kernel-spi"; + reg = <0x00100000 0x00500000>; + read-only; + }; + partition@600000 { + label = "dtb-spi"; + reg = <0x00600000 0x00100000>; + read-only; + }; + partition@700000 { + label = "file system-spi"; + reg = <0x00700000 0x00900000>; + }; + }; + }; + + ssi@15000 { + compatible = "fsl,mpc8610-ssi"; + cell-index = <0>; + reg = <0x15000 0x100>; + interrupts = <75 2>; + fsl,mode = "i2s-slave"; + codec-handle = <&wm8776>; + fsl,playback-dma = <&dma00>; + fsl,capture-dma = <&dma01>; + fsl,fifo-depth = <16>; + }; + + dma@c300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,eloplus-dma"; + reg = <0xc300 0x4>; + ranges = <0x0 0xc100 0x200>; + cell-index = <1>; + dma00: dma-channel@0 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x0 0x80>; + cell-index = <0>; + interrupts = <76 2>; + }; + dma01: dma-channel@80 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + cell-index = <1>; + interrupts = <77 2>; + }; + dma-channel@100 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + cell-index = <2>; + interrupts = <78 2>; + }; + dma-channel@180 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + cell-index = <3>; + interrupts = <79 2>; + }; + }; + + gpio: gpio-controller@f000 { + #gpio-cells = <2>; + compatible = "fsl,mpc8572-gpio"; + reg = <0xf000 0x100>; + interrupts = <47 0x2>; + gpio-controller; + }; + + L2: l2-cache-controller@20000 { + compatible = "fsl,p1022-l2-cache-controller"; + reg = <0x20000 0x1000>; + cache-line-size = <32>; // 32 bytes + cache-size = <0x40000>; // L2, 256K + interrupts = <16 2>; + }; + + dma@21300 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,eloplus-dma"; + reg = <0x21300 0x4>; + ranges = <0x0 0x21100 0x200>; + cell-index = <0>; + dma-channel@0 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x0 0x80>; + cell-index = <0>; + interrupts = <20 2>; + }; + dma-channel@80 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x80 0x80>; + cell-index = <1>; + interrupts = <21 2>; + }; + dma-channel@100 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x100 0x80>; + cell-index = <2>; + interrupts = <22 2>; + }; + dma-channel@180 { + compatible = "fsl,eloplus-dma-channel"; + reg = <0x180 0x80>; + cell-index = <3>; + interrupts = <23 2>; + }; + }; + + usb@22000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl-usb2-dr"; + reg = <0x22000 0x1000>; + interrupts = <28 0x2>; + phy_type = "ulpi"; + }; + + mdio@24000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,etsec2-mdio"; + reg = <0x24000 0x1000 0xb0030 0x4>; + + phy0: ethernet-phy@0 { + interrupts = <3 1>; + reg = <0x1>; + }; + phy1: ethernet-phy@1 { + interrupts = <9 1>; + reg = <0x2>; + }; + }; + + mdio@25000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,etsec2-mdio"; + reg = <0x25000 0x1000 0xb1030 0x4>; + }; + + enet0: ethernet@B0000 { + #address-cells = <1>; + #size-cells = <1>; + cell-index = <0>; + device_type = "network"; + model = "eTSEC"; + compatible = "fsl,etsec2"; + fsl,num_rx_queues = <0x8>; + fsl,num_tx_queues = <0x8>; + fsl,magic-packet; + fsl,wake-on-filer; + local-mac-address = [ 00 00 00 00 00 00 ]; + fixed-link = <1 1 1000 0 0>; + phy-handle = <&phy0>; + phy-connection-type = "rgmii-id"; + queue-group@0{ + #address-cells = <1>; + #size-cells = <1>; + reg = <0xB0000 0x1000>; + interrupts = <29 2 30 2 34 2>; + }; + queue-group@1{ + #address-cells = <1>; + #size-cells = <1>; + reg = <0xB4000 0x1000>; + interrupts = <17 2 18 2 24 2>; + }; + }; + + enet1: ethernet@B1000 { + #address-cells = <1>; + #size-cells = <1>; + cell-index = <0>; + device_type = "network"; + model = "eTSEC"; + compatible = "fsl,etsec2"; + fsl,num_rx_queues = <0x8>; + fsl,num_tx_queues = <0x8>; + local-mac-address = [ 00 00 00 00 00 00 ]; + fixed-link = <1 1 1000 0 0>; + phy-handle = <&phy1>; + phy-connection-type = "rgmii-id"; + queue-group@0{ + #address-cells = <1>; + #size-cells = <1>; + reg = <0xB1000 0x1000>; + interrupts = <35 2 36 2 40 2>; + }; + queue-group@1{ + #address-cells = <1>; + #size-cells = <1>; + reg = <0xB5000 0x1000>; + interrupts = <51 2 52 2 67 2>; + }; + }; + + sdhci@2e000 { + compatible = "fsl,p1022-esdhc", "fsl,esdhc"; + reg = <0x2e000 0x1000>; + interrupts = <72 0x2>; + fsl,sdhci-auto-cmd12; + /* Filled in by U-Boot */ + clock-frequency = <0>; + }; + + crypto@30000 { + compatible = "fsl,sec3.3", "fsl,sec3.1", "fsl,sec3.0", + "fsl,sec2.4", "fsl,sec2.2", "fsl,sec2.1", + "fsl,sec2.0"; + reg = <0x30000 0x10000>; + interrupts = <45 2 58 2>; + fsl,num-channels = <4>; + fsl,channel-fifo-len = <24>; + fsl,exec-units-mask = <0x97c>; + fsl,descriptor-types-mask = <0x3a30abf>; + }; + + sata@18000 { + compatible = "fsl,mpc8536-sata", "fsl,pq-sata"; + reg = <0x18000 0x1000>; + cell-index = <1>; + interrupts = <74 0x2>; + }; + + sata@19000 { + compatible = "fsl,mpc8536-sata", "fsl,pq-sata"; + reg = <0x19000 0x1000>; + cell-index = <2>; + interrupts = <41 0x2>; + }; + + power@e0070{ + compatible = "fsl,mpc8536-pmc", "fsl,mpc8548-pmc"; + reg = <0xe0070 0x20>; + }; + + display@10000 { + compatible = "fsl,diu", "fsl,p1022-diu"; + reg = <0x10000 1000>; + interrupts = <64 2>; + }; + + timer@41100 { + compatible = "fsl,mpic-global-timer"; + reg = <0x41100 0x204>; + interrupts = <0xf7 0x2>; + }; + + mpic: pic@40000 { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <2>; + reg = <0x40000 0x40000>; + compatible = "chrp,open-pic"; + device_type = "open-pic"; + }; + + msi@41600 { + compatible = "fsl,p1022-msi", "fsl,mpic-msi"; + reg = <0x41600 0x80>; + msi-available-ranges = <0 0x100>; + interrupts = < + 0xe0 0 + 0xe1 0 + 0xe2 0 + 0xe3 0 + 0xe4 0 + 0xe5 0 + 0xe6 0 + 0xe7 0>; + }; + + global-utilities@e0000 { //global utilities block + compatible = "fsl,p1022-guts"; + reg = <0xe0000 0x1000>; + fsl,has-rstcr; + }; + }; + + pci0: pcie@fffe09000 { + compatible = "fsl,p1022-pcie"; + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0xf 0xffe09000 0 0x1000>; + bus-range = <0 255>; + ranges = <0x2000000 0x0 0xa0000000 0xc 0x20000000 0x0 0x20000000 + 0x1000000 0x0 0x00000000 0xf 0xffc10000 0x0 0x10000>; + clock-frequency = <33333333>; + interrupts = <16 2>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = < + /* IDSEL 0x0 */ + 0000 0 0 1 &mpic 4 1 + 0000 0 0 2 &mpic 5 1 + 0000 0 0 3 &mpic 6 1 + 0000 0 0 4 &mpic 7 1 + >; + pcie@0 { + reg = <0x0 0x0 0x0 0x0 0x0>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + ranges = <0x2000000 0x0 0xe0000000 + 0x2000000 0x0 0xe0000000 + 0x0 0x20000000 + + 0x1000000 0x0 0x0 + 0x1000000 0x0 0x0 + 0x0 0x100000>; + }; + }; + + pci1: pcie@fffe0a000 { + compatible = "fsl,p1022-pcie"; + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0xf 0xffe0a000 0 0x1000>; + bus-range = <0 255>; + ranges = <0x2000000 0x0 0xc0000000 0xc 0x40000000 0x0 0x20000000 + 0x1000000 0x0 0x00000000 0xf 0xffc20000 0x0 0x10000>; + clock-frequency = <33333333>; + interrupts = <16 2>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = < + /* IDSEL 0x0 */ + 0000 0 0 1 &mpic 0 1 + 0000 0 0 2 &mpic 1 1 + 0000 0 0 3 &mpic 2 1 + 0000 0 0 4 &mpic 3 1 + >; + pcie@0 { + reg = <0x0 0x0 0x0 0x0 0x0>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + ranges = <0x2000000 0x0 0xe0000000 + 0x2000000 0x0 0xe0000000 + 0x0 0x20000000 + + 0x1000000 0x0 0x0 + 0x1000000 0x0 0x0 + 0x0 0x100000>; + }; + }; + + + pci2: pcie@fffe0b000 { + compatible = "fsl,p1022-pcie"; + device_type = "pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0xf 0xffe0b000 0 0x1000>; + bus-range = <0 255>; + ranges = <0x2000000 0x0 0x80000000 0xc 0x00000000 0x0 0x20000000 + 0x1000000 0x0 0x00000000 0xf 0xffc00000 0x0 0x10000>; + clock-frequency = <33333333>; + interrupts = <16 2>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = < + /* IDSEL 0x0 */ + 0000 0 0 1 &mpic 8 1 + 0000 0 0 2 &mpic 9 1 + 0000 0 0 3 &mpic 10 1 + 0000 0 0 4 &mpic 11 1 + >; + pcie@0 { + reg = <0x0 0x0 0x0 0x0 0x0>; + #size-cells = <2>; + #address-cells = <3>; + device_type = "pci"; + ranges = <0x2000000 0x0 0xe0000000 + 0x2000000 0x0 0xe0000000 + 0x0 0x20000000 + + 0x1000000 0x0 0x0 + 0x1000000 0x0 0x0 + 0x0 0x100000>; + }; + }; +}; -- cgit v1.2.1 From c4b6a77663f5879de20561144716cfb675815e82 Mon Sep 17 00:00:00 2001 From: Heiko Schocher Date: Tue, 23 Mar 2010 08:57:01 +0100 Subject: powerpc/8xx: Add support for the MPC8xx based boards from TQC Supported SMC1 (serial console), SCC1 Ethernet (10Mbps HD). FEC Ethernet, 8MB NOR CFI Flash. Tested on STK8xx with TQM860L (with FEC) and with TQM855M (without FEC). Signed-off-by: Heiko Schocher Signed-off-by: Kumar Gala --- arch/powerpc/boot/dts/tqm8xx.dts | 172 +++++++++++++++++++++++++++++++++++++++ 1 file changed, 172 insertions(+) create mode 100644 arch/powerpc/boot/dts/tqm8xx.dts (limited to 'arch/powerpc/boot/dts') diff --git a/arch/powerpc/boot/dts/tqm8xx.dts b/arch/powerpc/boot/dts/tqm8xx.dts new file mode 100644 index 000000000000..f6da7ec49a8e --- /dev/null +++ b/arch/powerpc/boot/dts/tqm8xx.dts @@ -0,0 +1,172 @@ +/* + * TQM8XX Device Tree Source + * + * Heiko Schocher + * 2010 DENX Software Engineering GmbH + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +/dts-v1/; + +/ { + model = "TQM8xx"; + compatible = "tqc,tqm8xx"; + #address-cells = <1>; + #size-cells = <1>; + + aliases { + ethernet0 = ð0; + ethernet1 = ð1; + mdio1 = &phy1; + serial0 = &smc1; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + PowerPC,860@0 { + device_type = "cpu"; + reg = <0x0>; + d-cache-line-size = <16>; // 16 bytes + i-cache-line-size = <16>; // 16 bytes + d-cache-size = <0x1000>; // L1, 4K + i-cache-size = <0x1000>; // L1, 4K + timebase-frequency = <0>; + bus-frequency = <0>; + clock-frequency = <0>; + interrupts = <15 2>; // decrementer interrupt + interrupt-parent = <&PIC>; + }; + }; + + memory { + device_type = "memory"; + reg = <0x0 0x2000000>; + }; + + localbus@fff00100 { + compatible = "fsl,mpc860-localbus", "fsl,pq1-localbus"; + #address-cells = <2>; + #size-cells = <1>; + reg = <0xfff00100 0x40>; + + ranges = < + 0x0 0x0 0x40000000 0x800000 + >; + + flash@0,0 { + compatible = "cfi-flash"; + reg = <0 0 0x800000>; + #address-cells = <1>; + #size-cells = <1>; + bank-width = <4>; + device-width = <2>; + }; + }; + + soc@fff00000 { + #address-cells = <1>; + #size-cells = <1>; + device_type = "soc"; + ranges = <0x0 0xfff00000 0x00004000>; + + phy1: mdio@e00 { + compatible = "fsl,mpc866-fec-mdio", "fsl,pq1-fec-mdio"; + reg = <0xe00 0x188>; + #address-cells = <1>; + #size-cells = <0>; + PHY: ethernet-phy@f { + reg = <0xf>; + device_type = "ethernet-phy"; + }; + }; + + eth1: ethernet@e00 { + device_type = "network"; + compatible = "fsl,mpc866-fec-enet", + "fsl,pq1-fec-enet"; + reg = <0xe00 0x188>; + interrupts = <3 1>; + interrupt-parent = <&PIC>; + phy-handle = <&PHY>; + linux,network-index = <1>; + }; + + PIC: pic@0 { + interrupt-controller; + #interrupt-cells = <2>; + reg = <0x0 0x24>; + compatible = "fsl,mpc860-pic", "fsl,pq1-pic"; + }; + + cpm@9c0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,mpc860-cpm", "fsl,cpm1"; + ranges; + reg = <0x9c0 0x40>; + brg-frequency = <0>; + interrupts = <0 2>; // cpm error interrupt + interrupt-parent = <&CPM_PIC>; + + muram@2000 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x2000 0x2000>; + + data@0 { + compatible = "fsl,cpm-muram-data"; + reg = <0x0 0x2000>; + }; + }; + + brg@9f0 { + compatible = "fsl,mpc860-brg", + "fsl,cpm1-brg", + "fsl,cpm-brg"; + reg = <0x9f0 0x10>; + clock-frequency = <0>; + }; + + CPM_PIC: pic@930 { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + interrupts = <5 2 0 2>; + interrupt-parent = <&PIC>; + reg = <0x930 0x20>; + compatible = "fsl,mpc860-cpm-pic", + "fsl,cpm1-pic"; + }; + + + smc1: serial@a80 { + device_type = "serial"; + compatible = "fsl,mpc860-smc-uart", + "fsl,cpm1-smc-uart"; + reg = <0xa80 0x10 0x3e80 0x40>; + interrupts = <4>; + interrupt-parent = <&CPM_PIC>; + fsl,cpm-brg = <1>; + fsl,cpm-command = <0x90>; + }; + + eth0: ethernet@a00 { + device_type = "network"; + compatible = "fsl,mpc860-scc-enet", + "fsl,cpm1-scc-enet"; + reg = <0xa00 0x18 0x3c00 0x100>; + interrupts = <30>; + interrupt-parent = <&CPM_PIC>; + fsl,cpm-command = <0000>; + linux,network-index = <0>; + fixed-link = <0 0 10 0 0>; + }; + }; + }; +}; -- cgit v1.2.1 From 05e57eec23eadf6641911ff07560f9ec7c6457c1 Mon Sep 17 00:00:00 2001 From: Roy Zang Date: Tue, 10 Aug 2010 18:02:00 -0700 Subject: dts: add sdhci,auto-cmd12 field for p4080 device tree Signed-off-by: Roy Zang Cc: Jerry Huang Cc: Benjamin Herrenschmidt Cc: Kumar Gala Cc: Grant Likely Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- arch/powerpc/boot/dts/p4080ds.dts | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/powerpc/boot/dts') diff --git a/arch/powerpc/boot/dts/p4080ds.dts b/arch/powerpc/boot/dts/p4080ds.dts index 6b29eab05362..efa00911f12b 100644 --- a/arch/powerpc/boot/dts/p4080ds.dts +++ b/arch/powerpc/boot/dts/p4080ds.dts @@ -280,6 +280,7 @@ reg = <0x114000 0x1000>; interrupts = <48 2>; interrupt-parent = <&mpic>; + sdhci,auto-cmd12; }; i2c@118000 { -- cgit v1.2.1 From 447bd479105c34416dad01c374873c34d8e25cfd Mon Sep 17 00:00:00 2001 From: Roy Zang Date: Tue, 10 Aug 2010 18:02:01 -0700 Subject: dts: add ESDHC weird voltage bits workaround P4080 ESDHC controller does not support 1.8V and 3.0V voltage. but the host controller capabilities register wrongly set the bits. This patch adds the workaround to correct the weird voltage setting bits. Only 3.3V voltage is supported for P4080 ESDHC controller. Signed-off-by: Roy Zang Cc: Jerry Huang Cc: Benjamin Herrenschmidt Cc: Kumar Gala Cc: Grant Likely Cc: Signed-off-by: Andrew Morton Signed-off-by: Linus Torvalds --- arch/powerpc/boot/dts/p4080ds.dts | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/powerpc/boot/dts') diff --git a/arch/powerpc/boot/dts/p4080ds.dts b/arch/powerpc/boot/dts/p4080ds.dts index efa00911f12b..2f0de24e3822 100644 --- a/arch/powerpc/boot/dts/p4080ds.dts +++ b/arch/powerpc/boot/dts/p4080ds.dts @@ -280,6 +280,7 @@ reg = <0x114000 0x1000>; interrupts = <48 2>; interrupt-parent = <&mpic>; + voltage-ranges = <3300 3300>; sdhci,auto-cmd12; }; -- cgit v1.2.1