From 3696d303d6a39f916f9ace37d79e3db7937c68a7 Mon Sep 17 00:00:00 2001 From: Bryan Buckley Date: Fri, 30 Sep 2011 11:05:55 -0700 Subject: ARM: OMAP4: MMC: fix power and audio issue, decouple USBC1 from MMC1 Remove OMAP4_USBC1_ICUSB_PWRDNZ_MASK during enable/disable PWRDNZ mode for MMC1_PBIAS and associated extended-drain MMC1 I/O cell. This is in accordance with the control module programming guide. This fixes a bug where if trying to use gpio_98 or gpio_99 and MMC1 at the same time the GPIO signal will be affected by a changing SDMMC1_VDDS. Software must keep MMC1_PBIAS cell and MMC1_IO cell PWRDNZ signals low whenever SDMMC1_VDDS ramps up/down or changes for cell protection purposes. MMC1 is based on SDMMC1_VDDS whereas USBC1 is based on SIM_VDDS therefore they can operate independently. Signed-off-by: Bryan Buckley Acked-by: Kishore Kadiyala Tested-by: Balaji T K Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/hsmmc.c | 12 ++++-------- 1 file changed, 4 insertions(+), 8 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/hsmmc.c b/arch/arm/mach-omap2/hsmmc.c index a9b45c76e1d3..097a42d81e59 100644 --- a/arch/arm/mach-omap2/hsmmc.c +++ b/arch/arm/mach-omap2/hsmmc.c @@ -137,8 +137,7 @@ static void omap4_hsmmc1_before_set_reg(struct device *dev, int slot, */ reg = omap4_ctrl_pad_readl(control_pbias_offset); reg &= ~(OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK | - OMAP4_MMC1_PWRDNZ_MASK | - OMAP4_USBC1_ICUSB_PWRDNZ_MASK); + OMAP4_MMC1_PWRDNZ_MASK); omap4_ctrl_pad_writel(reg, control_pbias_offset); } @@ -156,8 +155,7 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot, else reg |= OMAP4_MMC1_PBIASLITE_VMODE_MASK; reg |= (OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK | - OMAP4_MMC1_PWRDNZ_MASK | - OMAP4_USBC1_ICUSB_PWRDNZ_MASK); + OMAP4_MMC1_PWRDNZ_MASK); omap4_ctrl_pad_writel(reg, control_pbias_offset); timeout = jiffies + msecs_to_jiffies(5); @@ -171,16 +169,14 @@ static void omap4_hsmmc1_after_set_reg(struct device *dev, int slot, if (reg & OMAP4_MMC1_PBIASLITE_VMODE_ERROR_MASK) { pr_err("Pbias Voltage is not same as LDO\n"); /* Caution : On VMODE_ERROR Power Down MMC IO */ - reg &= ~(OMAP4_MMC1_PWRDNZ_MASK | - OMAP4_USBC1_ICUSB_PWRDNZ_MASK); + reg &= ~(OMAP4_MMC1_PWRDNZ_MASK); omap4_ctrl_pad_writel(reg, control_pbias_offset); } } else { reg = omap4_ctrl_pad_readl(control_pbias_offset); reg |= (OMAP4_MMC1_PBIASLITE_PWRDNZ_MASK | OMAP4_MMC1_PWRDNZ_MASK | - OMAP4_MMC1_PBIASLITE_VMODE_MASK | - OMAP4_USBC1_ICUSB_PWRDNZ_MASK); + OMAP4_MMC1_PBIASLITE_VMODE_MASK); omap4_ctrl_pad_writel(reg, control_pbias_offset); } } -- cgit v1.2.1 From bfd46a543f8f90bb197225900e355ce3c7daeb1f Mon Sep 17 00:00:00 2001 From: Tony Lindgren Date: Fri, 30 Sep 2011 11:05:55 -0700 Subject: ARM: OMAP: Fix i2c init for twl4030 Looks like 2600 kHz rate does not work reliably on 2430, so just use the 100 kHz rate. Otherwise the system often fails to boot properly with: omap_i2c omap_i2c.2: timeout waiting for bus ready omap_i2c omap_i2c.2: timeout waiting for bus ready twl: i2c_write failed to transfer all messages omap_i2c omap_i2c.2: timeout waiting for bus ready twl: i2c_write failed to transfer all messages omap_i2c omap_i2c.2: timeout waiting for bus ready twl: i2c_write failed to transfer all messages twl: clock init err [-110] omap_i2c omap_i2c.2: timeout waiting for bus ready twl: i2c_write failed to transfer all messages TWL4030 Unable to unlock IDCODE registers --110 Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/board-2430sdp.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/board-2430sdp.c b/arch/arm/mach-omap2/board-2430sdp.c index 2028464cf5b9..f79b7d2a8ed4 100644 --- a/arch/arm/mach-omap2/board-2430sdp.c +++ b/arch/arm/mach-omap2/board-2430sdp.c @@ -193,7 +193,8 @@ static int __init omap2430_i2c_init(void) { omap_register_i2c_bus(1, 100, sdp2430_i2c1_boardinfo, ARRAY_SIZE(sdp2430_i2c1_boardinfo)); - omap2_pmic_init("twl4030", &sdp2430_twldata); + omap_pmic_init(2, 100, "twl4030", INT_24XX_SYS_NIRQ, + &sdp2430_twldata); return 0; } -- cgit v1.2.1 From b8e111a74d281b70e88bd67fec48cfda4f9bdce2 Mon Sep 17 00:00:00 2001 From: Axel Lin Date: Fri, 30 Sep 2011 11:05:55 -0700 Subject: ARM: OMAP: musb: Remove a redundant omap4430_phy_init call in usb_musb_init Current code calls omap4430_phy_init() twice in usb_musb_init(). Calling omap4430_phy_init() once is enough. This patch removes the first omap4430_phy_init() call, which using an uninitialized pointer as parameter. This patch elimates below build warning: arch/arm/mach-omap2/usb-musb.c: In function 'usb_musb_init': arch/arm/mach-omap2/usb-musb.c:141: warning: 'dev' may be used uninitialized in this function Signed-off-by: Axel Lin Bjarne Steinsbo Acked-by: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/usb-musb.c | 3 --- 1 file changed, 3 deletions(-) (limited to 'arch/arm') diff --git a/arch/arm/mach-omap2/usb-musb.c b/arch/arm/mach-omap2/usb-musb.c index a65145b02a55..19e4dac62a8c 100644 --- a/arch/arm/mach-omap2/usb-musb.c +++ b/arch/arm/mach-omap2/usb-musb.c @@ -137,9 +137,6 @@ void __init usb_musb_init(struct omap_musb_board_data *musb_board_data) musb_plat.mode = board_data->mode; musb_plat.extvbus = board_data->extvbus; - if (cpu_is_omap44xx()) - omap4430_phy_init(dev); - if (cpu_is_omap3517() || cpu_is_omap3505()) { oh_name = "am35x_otg_hs"; name = "musb-am35x"; -- cgit v1.2.1