From 8c3abc7d903df492a7394b0adae4349d9a381aaf Mon Sep 17 00:00:00 2001 From: Russell King Date: Sat, 8 Nov 2008 20:25:21 +0000 Subject: [ARM] pxa: convert to clkdev and match clocks by struct device where possible Signed-off-by: Russell King --- arch/arm/mach-pxa/include/mach/clkdev.h | 7 +++++++ 1 file changed, 7 insertions(+) create mode 100644 arch/arm/mach-pxa/include/mach/clkdev.h (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/clkdev.h b/arch/arm/mach-pxa/include/mach/clkdev.h new file mode 100644 index 000000000000..04b37a89801c --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/clkdev.h @@ -0,0 +1,7 @@ +#ifndef __ASM_MACH_CLKDEV_H +#define __ASM_MACH_CLKDEV_H + +#define __clk_get(clk) ({ 1; }) +#define __clk_put(clk) do { } while (0) + +#endif -- cgit v1.2.1 From b5ee9002583fc14e6d45a04c18f208987a8fbced Mon Sep 17 00:00:00 2001 From: Nicolas Pitre Date: Fri, 5 Sep 2008 21:53:30 -0400 Subject: [ARM] remove a common set of __virt_to_bus definitions Let's provide an overridable default instead of having every machine class define __virt_to_bus and __bus_to_virt to the same thing. What most platforms are using is bus_addr == phys_addr so such is the default. One exception is ebsa110 which has no DMA what so ever, so the actual definition is not important except only for proper compilation. Also added a comment about the special footbridge bus translation. Let's also remove comments alluding to set_dma_addr which is not (and should not) be commonly used. Signed-off-by: Nicolas Pitre Signed-off-by: Russell King --- arch/arm/mach-pxa/include/mach/memory.h | 10 ---------- 1 file changed, 10 deletions(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/memory.h b/arch/arm/mach-pxa/include/mach/memory.h index 59aef89808d6..eac491c2d741 100644 --- a/arch/arm/mach-pxa/include/mach/memory.h +++ b/arch/arm/mach-pxa/include/mach/memory.h @@ -17,16 +17,6 @@ */ #define PHYS_OFFSET UL(0xa0000000) -/* - * Virtual view <-> DMA view memory address translations - * virt_to_bus: Used to translate the virtual address to an - * address suitable to be passed to set_dma_addr - * bus_to_virt: Used to convert an address for DMA operations - * to an address that the kernel can use. - */ -#define __virt_to_bus(x) __virt_to_phys(x) -#define __bus_to_virt(x) __phys_to_virt(x) - /* * The nodes are matched with the physical SDRAM banks as follows: * -- cgit v1.2.1 From 05678a96de2e97fdfd4b817478840ad6a02ea1d8 Mon Sep 17 00:00:00 2001 From: Russell King Date: Fri, 28 Nov 2008 16:04:54 +0000 Subject: [ARM] pxa: avoid polluting the kernel's namespace Avoid unnecessarily pollution of the kernel's namespace by avoiding mach/hardware.h. Include this header file where necessary. Signed-off-by: Russell King --- arch/arm/mach-pxa/include/mach/io.h | 2 -- 1 file changed, 2 deletions(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/io.h b/arch/arm/mach-pxa/include/mach/io.h index 600fd4f76603..38cb2123e9b2 100644 --- a/arch/arm/mach-pxa/include/mach/io.h +++ b/arch/arm/mach-pxa/include/mach/io.h @@ -6,8 +6,6 @@ #ifndef __ASM_ARM_ARCH_IO_H #define __ASM_ARM_ARCH_IO_H -#include - #define IO_SPACE_LIMIT 0xffffffff /* -- cgit v1.2.1 From 36033422639913dad1f3146d452116522c77f753 Mon Sep 17 00:00:00 2001 From: Ian Molton Date: Sun, 24 Aug 2008 19:21:26 +0100 Subject: [ARM] IrDA support for e7xx This patchset provides a fully functional SIR IrDA driver for the Toshiba e7xx PDAs. Signed-off-by: Ian Molton --- arch/arm/mach-pxa/include/mach/eseries-gpio.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/eseries-gpio.h b/arch/arm/mach-pxa/include/mach/eseries-gpio.h index 4c90b1310270..794bc338b4df 100644 --- a/arch/arm/mach-pxa/include/mach/eseries-gpio.h +++ b/arch/arm/mach-pxa/include/mach/eseries-gpio.h @@ -43,7 +43,7 @@ #define GPIO_E800_PCMCIA_PWR1 73 /* e7xx IrDA power control */ -#define GPIO_E7XX_IR_ON 38 +#define GPIO_E7XX_IR_OFF 38 /* ASIC related GPIOs */ #define GPIO_ESERIES_TMIO_IRQ 5 -- cgit v1.2.1 From 0560cf5aa51216b06874333a2fa26ca034d97bdb Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 30 Nov 2008 11:45:54 +0000 Subject: [ARM] Add a common typesafe __io implementation As Al did for Versatile in 2ad4f86b60b649fd7428265c08d73a3bd360c81b, add a typesafe __io implementation for platforms to use. Convert platforms to use this new simple typesafe implementation. Signed-off-by: Russell King --- arch/arm/mach-pxa/include/mach/io.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/io.h b/arch/arm/mach-pxa/include/mach/io.h index 38cb2123e9b2..262691fb97d8 100644 --- a/arch/arm/mach-pxa/include/mach/io.h +++ b/arch/arm/mach-pxa/include/mach/io.h @@ -12,7 +12,7 @@ * We don't actually have real ISA nor PCI buses, but there is so many * drivers out there that might just work if we fake them... */ -#define __io(a) ((void __iomem *)(a)) -#define __mem_pci(a) (a) +#define __io(a) __typesafe_io(a) +#define __mem_pci(a) (a) #endif -- cgit v1.2.1 From 3719ec5077d9a8bf293c494ff7eae766d6a70bbe Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 30 Nov 2008 13:26:47 +0000 Subject: [ARM] Ensure that both MAX_DMA_ADDRESS and ISA_DMA_THRESHOLD are defined Both of these symbols should be defined by a platform, or neither should be defined. Ensure that all platforms conform. Signed-off-by: Russell King --- arch/arm/mach-pxa/include/mach/memory.h | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/memory.h b/arch/arm/mach-pxa/include/mach/memory.h index eac491c2d741..f626730ee42e 100644 --- a/arch/arm/mach-pxa/include/mach/memory.h +++ b/arch/arm/mach-pxa/include/mach/memory.h @@ -37,6 +37,7 @@ void cmx2xx_pci_adjust_zones(int node, unsigned long *size, cmx2xx_pci_adjust_zones(node, size, holes) #define ISA_DMA_THRESHOLD (PHYS_OFFSET + SZ_64M - 1) +#define MAX_DMA_ADDRESS (PAGE_OFFSET + SZ_64M) #endif #endif -- cgit v1.2.1 From e88db8b91f1f5de24ae6bb3241d92fecaae64abf Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Wed, 26 Nov 2008 18:25:52 +0800 Subject: Revert "[ARM] pxa: introduce cpu_is_pxa26x()" This reverts commit da1a3dc0ebb4f9209a1939eaa6b18901e0cd7bc0. The originally proposed way in the above commit is incorrect. And there is no easy way to distinguish between pxa25x and pxa26x at run-time. Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/hardware.h | 2 -- 1 file changed, 2 deletions(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/hardware.h b/arch/arm/mach-pxa/include/mach/hardware.h index a582a6d9b92b..292a93af2b25 100644 --- a/arch/arm/mach-pxa/include/mach/hardware.h +++ b/arch/arm/mach-pxa/include/mach/hardware.h @@ -204,8 +204,6 @@ __cpu_is_pxa25x(read_cpuid_id()); \ }) -extern int cpu_is_pxa26x(void); - #define cpu_is_pxa27x() \ ({ \ __cpu_is_pxa27x(read_cpuid_id()); \ -- cgit v1.2.1 From 067455aa53a55404ded85227e87436478c2acc63 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Wed, 26 Nov 2008 18:12:04 +0800 Subject: [ARM] pxa: add support for additional GPIOs on PXA26x Original patch from Marek Vasut, the problems with PXA26x are: 1. there are additional 4 GPIOs 86,87,88,89 have their direction bits inverted in GPDR2, as well as their alternate function bits being '1' for their GPIO functionality in GAFRx 2. there is no easy way to decide if the processor is a pxa26x or a pxa250/pxa255 at run-time, so the assumption here is the pxa26x will be treated as one of the pxa25x variants, and board code should have a better knowledge of the processor it is featured Introduce pxa26x_init_irq() for the second purpose, and treat the additional GPIOs > 85 on PXA25x specially. Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code a bit when PXA26x support isn't needed. Board config options have to select this to enable the support for PXA26x. __gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x isn't selected. Signed-off-by: Marek Vasut Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/mfp-pxa25x.h | 31 +++++++++++++++++++++++++++++ 1 file changed, 31 insertions(+) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h b/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h index 617cab2cc8d0..a72869b73ee3 100644 --- a/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h +++ b/arch/arm/mach-pxa/include/mach/mfp-pxa25x.h @@ -158,4 +158,35 @@ #define GPIO76_LCD_PCLK MFP_CFG_OUT(GPIO76, AF2, DRIVE_LOW) #define GPIO77_LCD_BIAS MFP_CFG_OUT(GPIO77, AF2, DRIVE_LOW) +#ifdef CONFIG_CPU_PXA26x +/* GPIO */ +#define GPIO85_GPIO MFP_CFG_IN(GPIO85, AF0) +#define GPIO86_GPIO MFP_CFG_IN(GPIO86, AF1) +#define GPIO87_GPIO MFP_CFG_IN(GPIO87, AF1) +#define GPIO88_GPIO MFP_CFG_IN(GPIO88, AF1) +#define GPIO89_GPIO MFP_CFG_IN(GPIO89, AF1) + +/* SDRAM */ +#define GPIO86_nSDCS2 MFP_CFG_OUT(GPIO86, AF0, DRIVE_HIGH) +#define GPIO87_nSDCS3 MFP_CFG_OUT(GPIO87, AF0, DRIVE_HIGH) +#define GPIO88_RDnWR MFP_CFG_OUT(GPIO88, AF0, DRIVE_HIGH) +#define GPIO89_nACRESET MFP_CFG_OUT(GPIO89, AF0, DRIVE_HIGH) + +/* USB */ +#define GPIO9_USB_RCV MFP_CFG_IN(GPIO9, AF1) +#define GPIO32_USB_VP MFP_CFG_IN(GPIO32, AF2) +#define GPIO34_USB_VM MFP_CFG_IN(GPIO34, AF2) +#define GPIO39_USB_VPO MFP_CFG_OUT(GPIO39, AF3, DRIVE_LOW) +#define GPIO56_USB_VMO MFP_CFG_OUT(GPIO56, AF1, DRIVE_LOW) +#define GPIO57_USB_nOE MFP_CFG_OUT(GPIO57, AF1, DRIVE_HIGH) + +/* ASSP */ +#define GPIO28_ASSP_BITCLK_IN MFP_CFG_IN(GPIO28, AF3) +#define GPIO28_ASSP_BITCLK_OUT MFP_CFG_OUT(GPIO28, AF3, DRIVE_LOW) +#define GPIO29_ASSP_RXD MFP_CFG_IN(GPIO29, AF3) +#define GPIO30_ASSP_TXD MFP_CFG_OUT(GPIO30, AF3, DRIVE_LOW) +#define GPIO31_ASSP_SFRM_IN MFP_CFG_IN(GPIO31, AF1) +#define GPIO31_ASSP_SFRM_OUT MFP_CFG_OUT(GPIO31, AF3, DRIVE_LOW) +#endif + #endif /* __ASM_ARCH_MFP_PXA25X_H */ -- cgit v1.2.1 From 63e6552f7cc45739cd2f92c27f5081f753b70d04 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Sun, 30 Nov 2008 20:58:42 +0800 Subject: [ARM] pxa: removed unused declarations of pxa_gpio_* in hardware.h pxa_gpio_{get,set}_value() are not used anymore, remove them from hardware.h. Declaration of pxa_gpio_mode() is still being referenced and thus moved into pxa2xx-gpio.h Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/hardware.h | 15 --------------- arch/arm/mach-pxa/include/mach/pxa2xx-gpio.h | 5 +++++ 2 files changed, 5 insertions(+), 15 deletions(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/hardware.h b/arch/arm/mach-pxa/include/mach/hardware.h index 292a93af2b25..f6b4103ecc65 100644 --- a/arch/arm/mach-pxa/include/mach/hardware.h +++ b/arch/arm/mach-pxa/include/mach/hardware.h @@ -257,21 +257,6 @@ __cpu_is_pxa3xx(read_cpuid_id()); \ }) -/* - * Handy routine to set GPIO alternate functions - */ -extern int pxa_gpio_mode( int gpio_mode ); - -/* - * Return GPIO level, nonzero means high, zero is low - */ -extern int pxa_gpio_get_value(unsigned gpio); - -/* - * Set output GPIO level - */ -extern void pxa_gpio_set_value(unsigned gpio, int value); - /* * return current memory and LCD clock frequency in units of 10kHz */ diff --git a/arch/arm/mach-pxa/include/mach/pxa2xx-gpio.h b/arch/arm/mach-pxa/include/mach/pxa2xx-gpio.h index 6ef1dd09970b..d83393e25273 100644 --- a/arch/arm/mach-pxa/include/mach/pxa2xx-gpio.h +++ b/arch/arm/mach-pxa/include/mach/pxa2xx-gpio.h @@ -365,4 +365,9 @@ #define GPIO117_I2CSCL_MD (117 | GPIO_ALT_FN_1_IN) #define GPIO118_I2CSDA_MD (118 | GPIO_ALT_FN_1_IN) +/* + * Handy routine to set GPIO alternate functions + */ +extern int pxa_gpio_mode( int gpio_mode ); + #endif /* __ASM_ARCH_PXA2XX_GPIO_H */ -- cgit v1.2.1 From 013132cae84a36df8a88773a3e0391700d0a66d4 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Fri, 28 Nov 2008 09:16:52 +0800 Subject: [ARM] pxa: move camera (QCI) registers definition out of pxa-regs.h Signed-off-by: Eric Miao Acked-by: Guennadi Liakhovetski --- arch/arm/mach-pxa/include/mach/pxa-regs.h | 95 ------------------------------- 1 file changed, 95 deletions(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/pxa-regs.h b/arch/arm/mach-pxa/include/mach/pxa-regs.h index 15295d960000..0154e5a07cce 100644 --- a/arch/arm/mach-pxa/include/mach/pxa-regs.h +++ b/arch/arm/mach-pxa/include/mach/pxa-regs.h @@ -611,101 +611,6 @@ #ifdef CONFIG_PXA27x -/* Camera Interface */ -#define CICR0 __REG(0x50000000) -#define CICR1 __REG(0x50000004) -#define CICR2 __REG(0x50000008) -#define CICR3 __REG(0x5000000C) -#define CICR4 __REG(0x50000010) -#define CISR __REG(0x50000014) -#define CIFR __REG(0x50000018) -#define CITOR __REG(0x5000001C) -#define CIBR0 __REG(0x50000028) -#define CIBR1 __REG(0x50000030) -#define CIBR2 __REG(0x50000038) - -#define CICR0_DMAEN (1 << 31) /* DMA request enable */ -#define CICR0_PAR_EN (1 << 30) /* Parity enable */ -#define CICR0_SL_CAP_EN (1 << 29) /* Capture enable for slave mode */ -#define CICR0_ENB (1 << 28) /* Camera interface enable */ -#define CICR0_DIS (1 << 27) /* Camera interface disable */ -#define CICR0_SIM (0x7 << 24) /* Sensor interface mode mask */ -#define CICR0_TOM (1 << 9) /* Time-out mask */ -#define CICR0_RDAVM (1 << 8) /* Receive-data-available mask */ -#define CICR0_FEM (1 << 7) /* FIFO-empty mask */ -#define CICR0_EOLM (1 << 6) /* End-of-line mask */ -#define CICR0_PERRM (1 << 5) /* Parity-error mask */ -#define CICR0_QDM (1 << 4) /* Quick-disable mask */ -#define CICR0_CDM (1 << 3) /* Disable-done mask */ -#define CICR0_SOFM (1 << 2) /* Start-of-frame mask */ -#define CICR0_EOFM (1 << 1) /* End-of-frame mask */ -#define CICR0_FOM (1 << 0) /* FIFO-overrun mask */ - -#define CICR1_TBIT (1 << 31) /* Transparency bit */ -#define CICR1_RGBT_CONV (0x3 << 29) /* RGBT conversion mask */ -#define CICR1_PPL (0x7ff << 15) /* Pixels per line mask */ -#define CICR1_RGB_CONV (0x7 << 12) /* RGB conversion mask */ -#define CICR1_RGB_F (1 << 11) /* RGB format */ -#define CICR1_YCBCR_F (1 << 10) /* YCbCr format */ -#define CICR1_RGB_BPP (0x7 << 7) /* RGB bis per pixel mask */ -#define CICR1_RAW_BPP (0x3 << 5) /* Raw bis per pixel mask */ -#define CICR1_COLOR_SP (0x3 << 3) /* Color space mask */ -#define CICR1_DW (0x7 << 0) /* Data width mask */ - -#define CICR2_BLW (0xff << 24) /* Beginning-of-line pixel clock - wait count mask */ -#define CICR2_ELW (0xff << 16) /* End-of-line pixel clock - wait count mask */ -#define CICR2_HSW (0x3f << 10) /* Horizontal sync pulse width mask */ -#define CICR2_BFPW (0x3f << 3) /* Beginning-of-frame pixel clock - wait count mask */ -#define CICR2_FSW (0x7 << 0) /* Frame stabilization - wait count mask */ - -#define CICR3_BFW (0xff << 24) /* Beginning-of-frame line clock - wait count mask */ -#define CICR3_EFW (0xff << 16) /* End-of-frame line clock - wait count mask */ -#define CICR3_VSW (0x3f << 10) /* Vertical sync pulse width mask */ -#define CICR3_BFPW (0x3f << 3) /* Beginning-of-frame pixel clock - wait count mask */ -#define CICR3_LPF (0x7ff << 0) /* Lines per frame mask */ - -#define CICR4_MCLK_DLY (0x3 << 24) /* MCLK Data Capture Delay mask */ -#define CICR4_PCLK_EN (1 << 23) /* Pixel clock enable */ -#define CICR4_PCP (1 << 22) /* Pixel clock polarity */ -#define CICR4_HSP (1 << 21) /* Horizontal sync polarity */ -#define CICR4_VSP (1 << 20) /* Vertical sync polarity */ -#define CICR4_MCLK_EN (1 << 19) /* MCLK enable */ -#define CICR4_FR_RATE (0x7 << 8) /* Frame rate mask */ -#define CICR4_DIV (0xff << 0) /* Clock divisor mask */ - -#define CISR_FTO (1 << 15) /* FIFO time-out */ -#define CISR_RDAV_2 (1 << 14) /* Channel 2 receive data available */ -#define CISR_RDAV_1 (1 << 13) /* Channel 1 receive data available */ -#define CISR_RDAV_0 (1 << 12) /* Channel 0 receive data available */ -#define CISR_FEMPTY_2 (1 << 11) /* Channel 2 FIFO empty */ -#define CISR_FEMPTY_1 (1 << 10) /* Channel 1 FIFO empty */ -#define CISR_FEMPTY_0 (1 << 9) /* Channel 0 FIFO empty */ -#define CISR_EOL (1 << 8) /* End of line */ -#define CISR_PAR_ERR (1 << 7) /* Parity error */ -#define CISR_CQD (1 << 6) /* Camera interface quick disable */ -#define CISR_CDD (1 << 5) /* Camera interface disable done */ -#define CISR_SOF (1 << 4) /* Start of frame */ -#define CISR_EOF (1 << 3) /* End of frame */ -#define CISR_IFO_2 (1 << 2) /* FIFO overrun for Channel 2 */ -#define CISR_IFO_1 (1 << 1) /* FIFO overrun for Channel 1 */ -#define CISR_IFO_0 (1 << 0) /* FIFO overrun for Channel 0 */ - -#define CIFR_FLVL2 (0x7f << 23) /* FIFO 2 level mask */ -#define CIFR_FLVL1 (0x7f << 16) /* FIFO 1 level mask */ -#define CIFR_FLVL0 (0xff << 8) /* FIFO 0 level mask */ -#define CIFR_THL_0 (0x3 << 4) /* Threshold Level for Channel 0 FIFO */ -#define CIFR_RESET_F (1 << 3) /* Reset input FIFOs */ -#define CIFR_FEN2 (1 << 2) /* FIFO enable for channel 2 */ -#define CIFR_FEN1 (1 << 1) /* FIFO enable for channel 1 */ -#define CIFR_FEN0 (1 << 0) /* FIFO enable for channel 0 */ - #define SRAM_SIZE 0x40000 /* 4x64K */ #define SRAM_MEM_PHYS 0x5C000000 -- cgit v1.2.1 From b40ddf575883ceca303906556bcd0cff5c284fef Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Fri, 28 Nov 2008 11:13:47 +0800 Subject: [ARM] pxa: move FICP register definitions into pxaficp_ir.c Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/pxa-regs.h | 45 +------------------------------ 1 file changed, 1 insertion(+), 44 deletions(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/pxa-regs.h b/arch/arm/mach-pxa/include/mach/pxa-regs.h index 0154e5a07cce..9b44eb93abc8 100644 --- a/arch/arm/mach-pxa/include/mach/pxa-regs.h +++ b/arch/arm/mach-pxa/include/mach/pxa-regs.h @@ -369,52 +369,9 @@ /* - * Fast Infrared Communication Port + * Fast Infrared Communication Port - moved into drivers/net/irda/pxaficp_ir.c */ -#define FICP __REG(0x40800000) /* Start of FICP area */ -#define ICCR0 __REG(0x40800000) /* ICP Control Register 0 */ -#define ICCR1 __REG(0x40800004) /* ICP Control Register 1 */ -#define ICCR2 __REG(0x40800008) /* ICP Control Register 2 */ -#define ICDR __REG(0x4080000c) /* ICP Data Register */ -#define ICSR0 __REG(0x40800014) /* ICP Status Register 0 */ -#define ICSR1 __REG(0x40800018) /* ICP Status Register 1 */ - -#define ICCR0_AME (1 << 7) /* Address match enable */ -#define ICCR0_TIE (1 << 6) /* Transmit FIFO interrupt enable */ -#define ICCR0_RIE (1 << 5) /* Recieve FIFO interrupt enable */ -#define ICCR0_RXE (1 << 4) /* Receive enable */ -#define ICCR0_TXE (1 << 3) /* Transmit enable */ -#define ICCR0_TUS (1 << 2) /* Transmit FIFO underrun select */ -#define ICCR0_LBM (1 << 1) /* Loopback mode */ -#define ICCR0_ITR (1 << 0) /* IrDA transmission */ - -#define ICCR2_RXP (1 << 3) /* Receive Pin Polarity select */ -#define ICCR2_TXP (1 << 2) /* Transmit Pin Polarity select */ -#define ICCR2_TRIG (3 << 0) /* Receive FIFO Trigger threshold */ -#define ICCR2_TRIG_8 (0 << 0) /* >= 8 bytes */ -#define ICCR2_TRIG_16 (1 << 0) /* >= 16 bytes */ -#define ICCR2_TRIG_32 (2 << 0) /* >= 32 bytes */ - -#ifdef CONFIG_PXA27x -#define ICSR0_EOC (1 << 6) /* DMA End of Descriptor Chain */ -#endif -#define ICSR0_FRE (1 << 5) /* Framing error */ -#define ICSR0_RFS (1 << 4) /* Receive FIFO service request */ -#define ICSR0_TFS (1 << 3) /* Transnit FIFO service request */ -#define ICSR0_RAB (1 << 2) /* Receiver abort */ -#define ICSR0_TUR (1 << 1) /* Trunsmit FIFO underun */ -#define ICSR0_EIF (1 << 0) /* End/Error in FIFO */ - -#define ICSR1_ROR (1 << 6) /* Receiver FIFO underrun */ -#define ICSR1_CRE (1 << 5) /* CRC error */ -#define ICSR1_EOF (1 << 4) /* End of frame */ -#define ICSR1_TNF (1 << 3) /* Transmit FIFO not full */ -#define ICSR1_RNE (1 << 2) /* Receive FIFO not empty */ -#define ICSR1_TBY (1 << 1) /* Tramsmiter busy flag */ -#define ICSR1_RSY (1 << 0) /* Recevier synchronized flag */ - - /* * Real Time Clock */ -- cgit v1.2.1 From d15313e685759a676222ad85247ad8e1c138b9c7 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Thu, 27 Nov 2008 17:08:42 +0800 Subject: [ARM] pxa: remove unused PWM register definitions, use generic PWM API We now have generic PWM API for PXA, the PWM registers definitions are now used nowhere, and it is not encouraged to manipulate them directly by driver code. Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/pxa-regs.h | 13 ------------- 1 file changed, 13 deletions(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/pxa-regs.h b/arch/arm/mach-pxa/include/mach/pxa-regs.h index 9b44eb93abc8..6661ba481498 100644 --- a/arch/arm/mach-pxa/include/mach/pxa-regs.h +++ b/arch/arm/mach-pxa/include/mach/pxa-regs.h @@ -419,19 +419,6 @@ #define OIER_E0 (1 << 0) /* Interrupt enable channel 0 */ -/* - * Pulse Width Modulator - */ - -#define PWM_CTRL0 __REG(0x40B00000) /* PWM 0 Control Register */ -#define PWM_PWDUTY0 __REG(0x40B00004) /* PWM 0 Duty Cycle Register */ -#define PWM_PERVAL0 __REG(0x40B00008) /* PWM 0 Period Control Register */ - -#define PWM_CTRL1 __REG(0x40C00000) /* PWM 1Control Register */ -#define PWM_PWDUTY1 __REG(0x40C00004) /* PWM 1 Duty Cycle Register */ -#define PWM_PERVAL1 __REG(0x40C00008) /* PWM 1 Period Control Register */ - - /* * Interrupt Controller */ -- cgit v1.2.1 From a07efb5dac2a1c9125b9bd84d2f9ea4803d93e60 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Fri, 28 Nov 2008 13:38:03 +0800 Subject: [ARM] pxa: remove the now unused IMPMCR/IMPMSR register definitions There two are internal registers that are used to control the power management of the Internal Memory (i.e. Internal SRAM). They are referenced nowhere and removed here to simplify pxa-regs.h a bit. Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/pxa-regs.h | 54 ------------------------------- 1 file changed, 54 deletions(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/pxa-regs.h b/arch/arm/mach-pxa/include/mach/pxa-regs.h index 6661ba481498..859b35e1a7ee 100644 --- a/arch/arm/mach-pxa/include/mach/pxa-regs.h +++ b/arch/arm/mach-pxa/include/mach/pxa-regs.h @@ -553,60 +553,6 @@ * Core Clock - see arch/arm/mach-pxa/include/mach/pxa2xx-regs.h */ -#ifdef CONFIG_PXA27x - -#define SRAM_SIZE 0x40000 /* 4x64K */ - -#define SRAM_MEM_PHYS 0x5C000000 - -#define IMPMCR __REG(0x58000000) /* IM Power Management Control Reg */ -#define IMPMSR __REG(0x58000008) /* IM Power Management Status Reg */ - -#define IMPMCR_PC3 (0x3 << 22) /* Bank 3 Power Control */ -#define IMPMCR_PC3_RUN_MODE (0x0 << 22) /* Run mode */ -#define IMPMCR_PC3_STANDBY_MODE (0x1 << 22) /* Standby mode */ -#define IMPMCR_PC3_AUTO_MODE (0x3 << 22) /* Automatically controlled */ - -#define IMPMCR_PC2 (0x3 << 20) /* Bank 2 Power Control */ -#define IMPMCR_PC2_RUN_MODE (0x0 << 20) /* Run mode */ -#define IMPMCR_PC2_STANDBY_MODE (0x1 << 20) /* Standby mode */ -#define IMPMCR_PC2_AUTO_MODE (0x3 << 20) /* Automatically controlled */ - -#define IMPMCR_PC1 (0x3 << 18) /* Bank 1 Power Control */ -#define IMPMCR_PC1_RUN_MODE (0x0 << 18) /* Run mode */ -#define IMPMCR_PC1_STANDBY_MODE (0x1 << 18) /* Standby mode */ -#define IMPMCR_PC1_AUTO_MODE (0x3 << 18) /* Automatically controlled */ - -#define IMPMCR_PC0 (0x3 << 16) /* Bank 0 Power Control */ -#define IMPMCR_PC0_RUN_MODE (0x0 << 16) /* Run mode */ -#define IMPMCR_PC0_STANDBY_MODE (0x1 << 16) /* Standby mode */ -#define IMPMCR_PC0_AUTO_MODE (0x3 << 16) /* Automatically controlled */ - -#define IMPMCR_AW3 (1 << 11) /* Bank 3 Automatic Wake-up enable */ -#define IMPMCR_AW2 (1 << 10) /* Bank 2 Automatic Wake-up enable */ -#define IMPMCR_AW1 (1 << 9) /* Bank 1 Automatic Wake-up enable */ -#define IMPMCR_AW0 (1 << 8) /* Bank 0 Automatic Wake-up enable */ - -#define IMPMCR_DST (0xFF << 0) /* Delay Standby Time, ms */ - -#define IMPMSR_PS3 (0x3 << 6) /* Bank 3 Power Status: */ -#define IMPMSR_PS3_RUN_MODE (0x0 << 6) /* Run mode */ -#define IMPMSR_PS3_STANDBY_MODE (0x1 << 6) /* Standby mode */ - -#define IMPMSR_PS2 (0x3 << 4) /* Bank 2 Power Status: */ -#define IMPMSR_PS2_RUN_MODE (0x0 << 4) /* Run mode */ -#define IMPMSR_PS2_STANDBY_MODE (0x1 << 4) /* Standby mode */ - -#define IMPMSR_PS1 (0x3 << 2) /* Bank 1 Power Status: */ -#define IMPMSR_PS1_RUN_MODE (0x0 << 2) /* Run mode */ -#define IMPMSR_PS1_STANDBY_MODE (0x1 << 2) /* Standby mode */ - -#define IMPMSR_PS0 (0x3 << 0) /* Bank 0 Power Status: */ -#define IMPMSR_PS0_RUN_MODE (0x0 << 0) /* Run mode */ -#define IMPMSR_PS0_STANDBY_MODE (0x1 << 0) /* Standby mode */ - -#endif - /* PWRMODE register M field values */ #define PWRMODE_IDLE 0x1 -- cgit v1.2.1 From b31eca4f006c3efdd2dc501270172aa7ff8614b9 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Fri, 28 Nov 2008 13:49:22 +0800 Subject: [ARM] pxa: move pxa2xx specific PWRMODE definitions into pxa2xx-regs.h Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/pxa-regs.h | 7 ------- arch/arm/mach-pxa/include/mach/pxa2xx-regs.h | 7 +++++++ 2 files changed, 7 insertions(+), 7 deletions(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/pxa-regs.h b/arch/arm/mach-pxa/include/mach/pxa-regs.h index 859b35e1a7ee..ab62f6c11e0e 100644 --- a/arch/arm/mach-pxa/include/mach/pxa-regs.h +++ b/arch/arm/mach-pxa/include/mach/pxa-regs.h @@ -553,11 +553,4 @@ * Core Clock - see arch/arm/mach-pxa/include/mach/pxa2xx-regs.h */ -/* PWRMODE register M field values */ - -#define PWRMODE_IDLE 0x1 -#define PWRMODE_STANDBY 0x2 -#define PWRMODE_SLEEP 0x3 -#define PWRMODE_DEEPSLEEP 0x7 - #endif diff --git a/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h b/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h index 806ecfea44bf..2b71d87c898f 100644 --- a/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h +++ b/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h @@ -243,4 +243,11 @@ #define OSCC_OON (1 << 1) /* 32.768kHz OON (write-once only bit) */ #define OSCC_OOK (1 << 0) /* 32.768kHz OOK (read-only bit) */ +/* PWRMODE register M field values */ + +#define PWRMODE_IDLE 0x1 +#define PWRMODE_STANDBY 0x2 +#define PWRMODE_SLEEP 0x3 +#define PWRMODE_DEEPSLEEP 0x7 + #endif -- cgit v1.2.1 From 02f652626a8f23e513877cb751c8ea533739c28f Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Fri, 28 Nov 2008 14:08:53 +0800 Subject: [ARM] pxa: move UART register definitions into dedicated regs-uart.h Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/pxa-regs.h | 141 --------------------------- arch/arm/mach-pxa/include/mach/regs-uart.h | 143 ++++++++++++++++++++++++++++ arch/arm/mach-pxa/include/mach/uncompress.h | 2 +- 3 files changed, 144 insertions(+), 142 deletions(-) create mode 100644 arch/arm/mach-pxa/include/mach/regs-uart.h (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/pxa-regs.h b/arch/arm/mach-pxa/include/mach/pxa-regs.h index ab62f6c11e0e..cb9b46de97cc 100644 --- a/arch/arm/mach-pxa/include/mach/pxa-regs.h +++ b/arch/arm/mach-pxa/include/mach/pxa-regs.h @@ -123,147 +123,6 @@ #define DCMD_WIDTH4 (3 << 14) /* 4 byte width (Word) */ #define DCMD_LENGTH 0x01fff /* length mask (max = 8K - 1) */ - -/* - * UARTs - */ - -/* Full Function UART (FFUART) */ -#define FFUART FFRBR -#define FFRBR __REG(0x40100000) /* Receive Buffer Register (read only) */ -#define FFTHR __REG(0x40100000) /* Transmit Holding Register (write only) */ -#define FFIER __REG(0x40100004) /* Interrupt Enable Register (read/write) */ -#define FFIIR __REG(0x40100008) /* Interrupt ID Register (read only) */ -#define FFFCR __REG(0x40100008) /* FIFO Control Register (write only) */ -#define FFLCR __REG(0x4010000C) /* Line Control Register (read/write) */ -#define FFMCR __REG(0x40100010) /* Modem Control Register (read/write) */ -#define FFLSR __REG(0x40100014) /* Line Status Register (read only) */ -#define FFMSR __REG(0x40100018) /* Modem Status Register (read only) */ -#define FFSPR __REG(0x4010001C) /* Scratch Pad Register (read/write) */ -#define FFISR __REG(0x40100020) /* Infrared Selection Register (read/write) */ -#define FFDLL __REG(0x40100000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ -#define FFDLH __REG(0x40100004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ - -/* Bluetooth UART (BTUART) */ -#define BTUART BTRBR -#define BTRBR __REG(0x40200000) /* Receive Buffer Register (read only) */ -#define BTTHR __REG(0x40200000) /* Transmit Holding Register (write only) */ -#define BTIER __REG(0x40200004) /* Interrupt Enable Register (read/write) */ -#define BTIIR __REG(0x40200008) /* Interrupt ID Register (read only) */ -#define BTFCR __REG(0x40200008) /* FIFO Control Register (write only) */ -#define BTLCR __REG(0x4020000C) /* Line Control Register (read/write) */ -#define BTMCR __REG(0x40200010) /* Modem Control Register (read/write) */ -#define BTLSR __REG(0x40200014) /* Line Status Register (read only) */ -#define BTMSR __REG(0x40200018) /* Modem Status Register (read only) */ -#define BTSPR __REG(0x4020001C) /* Scratch Pad Register (read/write) */ -#define BTISR __REG(0x40200020) /* Infrared Selection Register (read/write) */ -#define BTDLL __REG(0x40200000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ -#define BTDLH __REG(0x40200004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ - -/* Standard UART (STUART) */ -#define STUART STRBR -#define STRBR __REG(0x40700000) /* Receive Buffer Register (read only) */ -#define STTHR __REG(0x40700000) /* Transmit Holding Register (write only) */ -#define STIER __REG(0x40700004) /* Interrupt Enable Register (read/write) */ -#define STIIR __REG(0x40700008) /* Interrupt ID Register (read only) */ -#define STFCR __REG(0x40700008) /* FIFO Control Register (write only) */ -#define STLCR __REG(0x4070000C) /* Line Control Register (read/write) */ -#define STMCR __REG(0x40700010) /* Modem Control Register (read/write) */ -#define STLSR __REG(0x40700014) /* Line Status Register (read only) */ -#define STMSR __REG(0x40700018) /* Reserved */ -#define STSPR __REG(0x4070001C) /* Scratch Pad Register (read/write) */ -#define STISR __REG(0x40700020) /* Infrared Selection Register (read/write) */ -#define STDLL __REG(0x40700000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ -#define STDLH __REG(0x40700004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ - -/* Hardware UART (HWUART) */ -#define HWUART HWRBR -#define HWRBR __REG(0x41600000) /* Receive Buffer Register (read only) */ -#define HWTHR __REG(0x41600000) /* Transmit Holding Register (write only) */ -#define HWIER __REG(0x41600004) /* Interrupt Enable Register (read/write) */ -#define HWIIR __REG(0x41600008) /* Interrupt ID Register (read only) */ -#define HWFCR __REG(0x41600008) /* FIFO Control Register (write only) */ -#define HWLCR __REG(0x4160000C) /* Line Control Register (read/write) */ -#define HWMCR __REG(0x41600010) /* Modem Control Register (read/write) */ -#define HWLSR __REG(0x41600014) /* Line Status Register (read only) */ -#define HWMSR __REG(0x41600018) /* Modem Status Register (read only) */ -#define HWSPR __REG(0x4160001C) /* Scratch Pad Register (read/write) */ -#define HWISR __REG(0x41600020) /* Infrared Selection Register (read/write) */ -#define HWFOR __REG(0x41600024) /* Receive FIFO Occupancy Register (read only) */ -#define HWABR __REG(0x41600028) /* Auto-Baud Control Register (read/write) */ -#define HWACR __REG(0x4160002C) /* Auto-Baud Count Register (read only) */ -#define HWDLL __REG(0x41600000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ -#define HWDLH __REG(0x41600004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ - -#define IER_DMAE (1 << 7) /* DMA Requests Enable */ -#define IER_UUE (1 << 6) /* UART Unit Enable */ -#define IER_NRZE (1 << 5) /* NRZ coding Enable */ -#define IER_RTIOE (1 << 4) /* Receiver Time Out Interrupt Enable */ -#define IER_MIE (1 << 3) /* Modem Interrupt Enable */ -#define IER_RLSE (1 << 2) /* Receiver Line Status Interrupt Enable */ -#define IER_TIE (1 << 1) /* Transmit Data request Interrupt Enable */ -#define IER_RAVIE (1 << 0) /* Receiver Data Available Interrupt Enable */ - -#define IIR_FIFOES1 (1 << 7) /* FIFO Mode Enable Status */ -#define IIR_FIFOES0 (1 << 6) /* FIFO Mode Enable Status */ -#define IIR_TOD (1 << 3) /* Time Out Detected */ -#define IIR_IID2 (1 << 2) /* Interrupt Source Encoded */ -#define IIR_IID1 (1 << 1) /* Interrupt Source Encoded */ -#define IIR_IP (1 << 0) /* Interrupt Pending (active low) */ - -#define FCR_ITL2 (1 << 7) /* Interrupt Trigger Level */ -#define FCR_ITL1 (1 << 6) /* Interrupt Trigger Level */ -#define FCR_RESETTF (1 << 2) /* Reset Transmitter FIFO */ -#define FCR_RESETRF (1 << 1) /* Reset Receiver FIFO */ -#define FCR_TRFIFOE (1 << 0) /* Transmit and Receive FIFO Enable */ -#define FCR_ITL_1 (0) -#define FCR_ITL_8 (FCR_ITL1) -#define FCR_ITL_16 (FCR_ITL2) -#define FCR_ITL_32 (FCR_ITL2|FCR_ITL1) - -#define LCR_DLAB (1 << 7) /* Divisor Latch Access Bit */ -#define LCR_SB (1 << 6) /* Set Break */ -#define LCR_STKYP (1 << 5) /* Sticky Parity */ -#define LCR_EPS (1 << 4) /* Even Parity Select */ -#define LCR_PEN (1 << 3) /* Parity Enable */ -#define LCR_STB (1 << 2) /* Stop Bit */ -#define LCR_WLS1 (1 << 1) /* Word Length Select */ -#define LCR_WLS0 (1 << 0) /* Word Length Select */ - -#define LSR_FIFOE (1 << 7) /* FIFO Error Status */ -#define LSR_TEMT (1 << 6) /* Transmitter Empty */ -#define LSR_TDRQ (1 << 5) /* Transmit Data Request */ -#define LSR_BI (1 << 4) /* Break Interrupt */ -#define LSR_FE (1 << 3) /* Framing Error */ -#define LSR_PE (1 << 2) /* Parity Error */ -#define LSR_OE (1 << 1) /* Overrun Error */ -#define LSR_DR (1 << 0) /* Data Ready */ - -#define MCR_LOOP (1 << 4) -#define MCR_OUT2 (1 << 3) /* force MSR_DCD in loopback mode */ -#define MCR_OUT1 (1 << 2) /* force MSR_RI in loopback mode */ -#define MCR_RTS (1 << 1) /* Request to Send */ -#define MCR_DTR (1 << 0) /* Data Terminal Ready */ - -#define MSR_DCD (1 << 7) /* Data Carrier Detect */ -#define MSR_RI (1 << 6) /* Ring Indicator */ -#define MSR_DSR (1 << 5) /* Data Set Ready */ -#define MSR_CTS (1 << 4) /* Clear To Send */ -#define MSR_DDCD (1 << 3) /* Delta Data Carrier Detect */ -#define MSR_TERI (1 << 2) /* Trailing Edge Ring Indicator */ -#define MSR_DDSR (1 << 1) /* Delta Data Set Ready */ -#define MSR_DCTS (1 << 0) /* Delta Clear To Send */ - -/* - * IrSR (Infrared Selection Register) - */ -#define STISR_RXPL (1 << 4) /* Receive Data Polarity */ -#define STISR_TXPL (1 << 3) /* Transmit Data Polarity */ -#define STISR_XMODE (1 << 2) /* Transmit Pulse Width Select */ -#define STISR_RCVEIR (1 << 1) /* Receiver SIR Enable */ -#define STISR_XMITIR (1 << 0) /* Transmitter SIR Enable */ - - /* * I2C registers - moved into drivers/i2c/busses/i2c-pxa.c */ diff --git a/arch/arm/mach-pxa/include/mach/regs-uart.h b/arch/arm/mach-pxa/include/mach/regs-uart.h new file mode 100644 index 000000000000..55aeb7fb72f6 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/regs-uart.h @@ -0,0 +1,143 @@ +#ifndef __ASM_ARCH_REGS_UART_H +#define __ASM_ARCH_REGS_UART_H + +/* + * UARTs + */ + +/* Full Function UART (FFUART) */ +#define FFUART FFRBR +#define FFRBR __REG(0x40100000) /* Receive Buffer Register (read only) */ +#define FFTHR __REG(0x40100000) /* Transmit Holding Register (write only) */ +#define FFIER __REG(0x40100004) /* Interrupt Enable Register (read/write) */ +#define FFIIR __REG(0x40100008) /* Interrupt ID Register (read only) */ +#define FFFCR __REG(0x40100008) /* FIFO Control Register (write only) */ +#define FFLCR __REG(0x4010000C) /* Line Control Register (read/write) */ +#define FFMCR __REG(0x40100010) /* Modem Control Register (read/write) */ +#define FFLSR __REG(0x40100014) /* Line Status Register (read only) */ +#define FFMSR __REG(0x40100018) /* Modem Status Register (read only) */ +#define FFSPR __REG(0x4010001C) /* Scratch Pad Register (read/write) */ +#define FFISR __REG(0x40100020) /* Infrared Selection Register (read/write) */ +#define FFDLL __REG(0x40100000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ +#define FFDLH __REG(0x40100004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ + +/* Bluetooth UART (BTUART) */ +#define BTUART BTRBR +#define BTRBR __REG(0x40200000) /* Receive Buffer Register (read only) */ +#define BTTHR __REG(0x40200000) /* Transmit Holding Register (write only) */ +#define BTIER __REG(0x40200004) /* Interrupt Enable Register (read/write) */ +#define BTIIR __REG(0x40200008) /* Interrupt ID Register (read only) */ +#define BTFCR __REG(0x40200008) /* FIFO Control Register (write only) */ +#define BTLCR __REG(0x4020000C) /* Line Control Register (read/write) */ +#define BTMCR __REG(0x40200010) /* Modem Control Register (read/write) */ +#define BTLSR __REG(0x40200014) /* Line Status Register (read only) */ +#define BTMSR __REG(0x40200018) /* Modem Status Register (read only) */ +#define BTSPR __REG(0x4020001C) /* Scratch Pad Register (read/write) */ +#define BTISR __REG(0x40200020) /* Infrared Selection Register (read/write) */ +#define BTDLL __REG(0x40200000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ +#define BTDLH __REG(0x40200004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ + +/* Standard UART (STUART) */ +#define STUART STRBR +#define STRBR __REG(0x40700000) /* Receive Buffer Register (read only) */ +#define STTHR __REG(0x40700000) /* Transmit Holding Register (write only) */ +#define STIER __REG(0x40700004) /* Interrupt Enable Register (read/write) */ +#define STIIR __REG(0x40700008) /* Interrupt ID Register (read only) */ +#define STFCR __REG(0x40700008) /* FIFO Control Register (write only) */ +#define STLCR __REG(0x4070000C) /* Line Control Register (read/write) */ +#define STMCR __REG(0x40700010) /* Modem Control Register (read/write) */ +#define STLSR __REG(0x40700014) /* Line Status Register (read only) */ +#define STMSR __REG(0x40700018) /* Reserved */ +#define STSPR __REG(0x4070001C) /* Scratch Pad Register (read/write) */ +#define STISR __REG(0x40700020) /* Infrared Selection Register (read/write) */ +#define STDLL __REG(0x40700000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ +#define STDLH __REG(0x40700004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ + +/* Hardware UART (HWUART) */ +#define HWUART HWRBR +#define HWRBR __REG(0x41600000) /* Receive Buffer Register (read only) */ +#define HWTHR __REG(0x41600000) /* Transmit Holding Register (write only) */ +#define HWIER __REG(0x41600004) /* Interrupt Enable Register (read/write) */ +#define HWIIR __REG(0x41600008) /* Interrupt ID Register (read only) */ +#define HWFCR __REG(0x41600008) /* FIFO Control Register (write only) */ +#define HWLCR __REG(0x4160000C) /* Line Control Register (read/write) */ +#define HWMCR __REG(0x41600010) /* Modem Control Register (read/write) */ +#define HWLSR __REG(0x41600014) /* Line Status Register (read only) */ +#define HWMSR __REG(0x41600018) /* Modem Status Register (read only) */ +#define HWSPR __REG(0x4160001C) /* Scratch Pad Register (read/write) */ +#define HWISR __REG(0x41600020) /* Infrared Selection Register (read/write) */ +#define HWFOR __REG(0x41600024) /* Receive FIFO Occupancy Register (read only) */ +#define HWABR __REG(0x41600028) /* Auto-Baud Control Register (read/write) */ +#define HWACR __REG(0x4160002C) /* Auto-Baud Count Register (read only) */ +#define HWDLL __REG(0x41600000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ +#define HWDLH __REG(0x41600004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ + +#define IER_DMAE (1 << 7) /* DMA Requests Enable */ +#define IER_UUE (1 << 6) /* UART Unit Enable */ +#define IER_NRZE (1 << 5) /* NRZ coding Enable */ +#define IER_RTIOE (1 << 4) /* Receiver Time Out Interrupt Enable */ +#define IER_MIE (1 << 3) /* Modem Interrupt Enable */ +#define IER_RLSE (1 << 2) /* Receiver Line Status Interrupt Enable */ +#define IER_TIE (1 << 1) /* Transmit Data request Interrupt Enable */ +#define IER_RAVIE (1 << 0) /* Receiver Data Available Interrupt Enable */ + +#define IIR_FIFOES1 (1 << 7) /* FIFO Mode Enable Status */ +#define IIR_FIFOES0 (1 << 6) /* FIFO Mode Enable Status */ +#define IIR_TOD (1 << 3) /* Time Out Detected */ +#define IIR_IID2 (1 << 2) /* Interrupt Source Encoded */ +#define IIR_IID1 (1 << 1) /* Interrupt Source Encoded */ +#define IIR_IP (1 << 0) /* Interrupt Pending (active low) */ + +#define FCR_ITL2 (1 << 7) /* Interrupt Trigger Level */ +#define FCR_ITL1 (1 << 6) /* Interrupt Trigger Level */ +#define FCR_RESETTF (1 << 2) /* Reset Transmitter FIFO */ +#define FCR_RESETRF (1 << 1) /* Reset Receiver FIFO */ +#define FCR_TRFIFOE (1 << 0) /* Transmit and Receive FIFO Enable */ +#define FCR_ITL_1 (0) +#define FCR_ITL_8 (FCR_ITL1) +#define FCR_ITL_16 (FCR_ITL2) +#define FCR_ITL_32 (FCR_ITL2|FCR_ITL1) + +#define LCR_DLAB (1 << 7) /* Divisor Latch Access Bit */ +#define LCR_SB (1 << 6) /* Set Break */ +#define LCR_STKYP (1 << 5) /* Sticky Parity */ +#define LCR_EPS (1 << 4) /* Even Parity Select */ +#define LCR_PEN (1 << 3) /* Parity Enable */ +#define LCR_STB (1 << 2) /* Stop Bit */ +#define LCR_WLS1 (1 << 1) /* Word Length Select */ +#define LCR_WLS0 (1 << 0) /* Word Length Select */ + +#define LSR_FIFOE (1 << 7) /* FIFO Error Status */ +#define LSR_TEMT (1 << 6) /* Transmitter Empty */ +#define LSR_TDRQ (1 << 5) /* Transmit Data Request */ +#define LSR_BI (1 << 4) /* Break Interrupt */ +#define LSR_FE (1 << 3) /* Framing Error */ +#define LSR_PE (1 << 2) /* Parity Error */ +#define LSR_OE (1 << 1) /* Overrun Error */ +#define LSR_DR (1 << 0) /* Data Ready */ + +#define MCR_LOOP (1 << 4) +#define MCR_OUT2 (1 << 3) /* force MSR_DCD in loopback mode */ +#define MCR_OUT1 (1 << 2) /* force MSR_RI in loopback mode */ +#define MCR_RTS (1 << 1) /* Request to Send */ +#define MCR_DTR (1 << 0) /* Data Terminal Ready */ + +#define MSR_DCD (1 << 7) /* Data Carrier Detect */ +#define MSR_RI (1 << 6) /* Ring Indicator */ +#define MSR_DSR (1 << 5) /* Data Set Ready */ +#define MSR_CTS (1 << 4) /* Clear To Send */ +#define MSR_DDCD (1 << 3) /* Delta Data Carrier Detect */ +#define MSR_TERI (1 << 2) /* Trailing Edge Ring Indicator */ +#define MSR_DDSR (1 << 1) /* Delta Data Set Ready */ +#define MSR_DCTS (1 << 0) /* Delta Clear To Send */ + +/* + * IrSR (Infrared Selection Register) + */ +#define STISR_RXPL (1 << 4) /* Receive Data Polarity */ +#define STISR_TXPL (1 << 3) /* Transmit Data Polarity */ +#define STISR_XMODE (1 << 2) /* Transmit Pulse Width Select */ +#define STISR_RCVEIR (1 << 1) /* Receiver SIR Enable */ +#define STISR_XMITIR (1 << 0) /* Transmitter SIR Enable */ + +#endif /* __ASM_ARCH_REGS_UART_H */ diff --git a/arch/arm/mach-pxa/include/mach/uncompress.h b/arch/arm/mach-pxa/include/mach/uncompress.h index 21e3e890af98..a9a4f302b6ef 100644 --- a/arch/arm/mach-pxa/include/mach/uncompress.h +++ b/arch/arm/mach-pxa/include/mach/uncompress.h @@ -10,7 +10,7 @@ */ #include -#include +#include #include #define __REG(x) ((volatile unsigned long *)x) -- cgit v1.2.1 From 1f017a9964c5b3b9581d3a5732110cb1e0444281 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Fri, 28 Nov 2008 14:19:33 +0800 Subject: [ARM] pxa: move AC97 register definitions into dedicated regs-ac97.h The optimal change would be to move the AC97 register definitions into the AC97 driver, unfortunately, the registers are shared between several files. Move them into a dedicated regs-ac97.h first. Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/pxa-regs.h | 96 ----------------------------- arch/arm/mach-pxa/include/mach/regs-ac97.h | 99 ++++++++++++++++++++++++++++++ 2 files changed, 99 insertions(+), 96 deletions(-) create mode 100644 arch/arm/mach-pxa/include/mach/regs-ac97.h (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/pxa-regs.h b/arch/arm/mach-pxa/include/mach/pxa-regs.h index cb9b46de97cc..a56502898030 100644 --- a/arch/arm/mach-pxa/include/mach/pxa-regs.h +++ b/arch/arm/mach-pxa/include/mach/pxa-regs.h @@ -131,102 +131,6 @@ * Serial Audio Controller - moved into sound/soc/pxa/pxa2xx-i2s.c */ -/* - * AC97 Controller registers - */ - -#define POCR __REG(0x40500000) /* PCM Out Control Register */ -#define POCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */ -#define POCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ - -#define PICR __REG(0x40500004) /* PCM In Control Register */ -#define PICR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */ -#define PICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ - -#define MCCR __REG(0x40500008) /* Mic In Control Register */ -#define MCCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */ -#define MCCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ - -#define GCR __REG(0x4050000C) /* Global Control Register */ -#ifdef CONFIG_PXA3xx -#define GCR_CLKBPB (1 << 31) /* Internal clock enable */ -#endif -#define GCR_nDMAEN (1 << 24) /* non DMA Enable */ -#define GCR_CDONE_IE (1 << 19) /* Command Done Interrupt Enable */ -#define GCR_SDONE_IE (1 << 18) /* Status Done Interrupt Enable */ -#define GCR_SECRDY_IEN (1 << 9) /* Secondary Ready Interrupt Enable */ -#define GCR_PRIRDY_IEN (1 << 8) /* Primary Ready Interrupt Enable */ -#define GCR_SECRES_IEN (1 << 5) /* Secondary Resume Interrupt Enable */ -#define GCR_PRIRES_IEN (1 << 4) /* Primary Resume Interrupt Enable */ -#define GCR_ACLINK_OFF (1 << 3) /* AC-link Shut Off */ -#define GCR_WARM_RST (1 << 2) /* AC97 Warm Reset */ -#define GCR_COLD_RST (1 << 1) /* AC'97 Cold Reset (0 = active) */ -#define GCR_GIE (1 << 0) /* Codec GPI Interrupt Enable */ - -#define POSR __REG(0x40500010) /* PCM Out Status Register */ -#define POSR_FIFOE (1 << 4) /* FIFO error */ -#define POSR_FSR (1 << 2) /* FIFO Service Request */ - -#define PISR __REG(0x40500014) /* PCM In Status Register */ -#define PISR_FIFOE (1 << 4) /* FIFO error */ -#define PISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */ -#define PISR_FSR (1 << 2) /* FIFO Service Request */ - -#define MCSR __REG(0x40500018) /* Mic In Status Register */ -#define MCSR_FIFOE (1 << 4) /* FIFO error */ -#define MCSR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */ -#define MCSR_FSR (1 << 2) /* FIFO Service Request */ - -#define GSR __REG(0x4050001C) /* Global Status Register */ -#define GSR_CDONE (1 << 19) /* Command Done */ -#define GSR_SDONE (1 << 18) /* Status Done */ -#define GSR_RDCS (1 << 15) /* Read Completion Status */ -#define GSR_BIT3SLT12 (1 << 14) /* Bit 3 of slot 12 */ -#define GSR_BIT2SLT12 (1 << 13) /* Bit 2 of slot 12 */ -#define GSR_BIT1SLT12 (1 << 12) /* Bit 1 of slot 12 */ -#define GSR_SECRES (1 << 11) /* Secondary Resume Interrupt */ -#define GSR_PRIRES (1 << 10) /* Primary Resume Interrupt */ -#define GSR_SCR (1 << 9) /* Secondary Codec Ready */ -#define GSR_PCR (1 << 8) /* Primary Codec Ready */ -#define GSR_MCINT (1 << 7) /* Mic In Interrupt */ -#define GSR_POINT (1 << 6) /* PCM Out Interrupt */ -#define GSR_PIINT (1 << 5) /* PCM In Interrupt */ -#define GSR_ACOFFD (1 << 3) /* AC-link Shut Off Done */ -#define GSR_MOINT (1 << 2) /* Modem Out Interrupt */ -#define GSR_MIINT (1 << 1) /* Modem In Interrupt */ -#define GSR_GSCI (1 << 0) /* Codec GPI Status Change Interrupt */ - -#define CAR __REG(0x40500020) /* CODEC Access Register */ -#define CAR_CAIP (1 << 0) /* Codec Access In Progress */ - -#define PCDR __REG(0x40500040) /* PCM FIFO Data Register */ -#define MCDR __REG(0x40500060) /* Mic-in FIFO Data Register */ - -#define MOCR __REG(0x40500100) /* Modem Out Control Register */ -#define MOCR_FEIE (1 << 3) /* FIFO Error */ -#define MOCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ - -#define MICR __REG(0x40500108) /* Modem In Control Register */ -#define MICR_FEIE (1 << 3) /* FIFO Error */ -#define MICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ - -#define MOSR __REG(0x40500110) /* Modem Out Status Register */ -#define MOSR_FIFOE (1 << 4) /* FIFO error */ -#define MOSR_FSR (1 << 2) /* FIFO Service Request */ - -#define MISR __REG(0x40500118) /* Modem In Status Register */ -#define MISR_FIFOE (1 << 4) /* FIFO error */ -#define MISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */ -#define MISR_FSR (1 << 2) /* FIFO Service Request */ - -#define MODR __REG(0x40500140) /* Modem FIFO Data Register */ - -#define PAC_REG_BASE __REG(0x40500200) /* Primary Audio Codec */ -#define SAC_REG_BASE __REG(0x40500300) /* Secondary Audio Codec */ -#define PMC_REG_BASE __REG(0x40500400) /* Primary Modem Codec */ -#define SMC_REG_BASE __REG(0x40500500) /* Secondary Modem Codec */ - - /* * Fast Infrared Communication Port - moved into drivers/net/irda/pxaficp_ir.c */ diff --git a/arch/arm/mach-pxa/include/mach/regs-ac97.h b/arch/arm/mach-pxa/include/mach/regs-ac97.h new file mode 100644 index 000000000000..e41b9d202b8c --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/regs-ac97.h @@ -0,0 +1,99 @@ +#ifndef __ASM_ARCH_REGS_AC97_H +#define __ASM_ARCH_REGS_AC97_H + +/* + * AC97 Controller registers + */ + +#define POCR __REG(0x40500000) /* PCM Out Control Register */ +#define POCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */ +#define POCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ + +#define PICR __REG(0x40500004) /* PCM In Control Register */ +#define PICR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */ +#define PICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ + +#define MCCR __REG(0x40500008) /* Mic In Control Register */ +#define MCCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */ +#define MCCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ + +#define GCR __REG(0x4050000C) /* Global Control Register */ +#ifdef CONFIG_PXA3xx +#define GCR_CLKBPB (1 << 31) /* Internal clock enable */ +#endif +#define GCR_nDMAEN (1 << 24) /* non DMA Enable */ +#define GCR_CDONE_IE (1 << 19) /* Command Done Interrupt Enable */ +#define GCR_SDONE_IE (1 << 18) /* Status Done Interrupt Enable */ +#define GCR_SECRDY_IEN (1 << 9) /* Secondary Ready Interrupt Enable */ +#define GCR_PRIRDY_IEN (1 << 8) /* Primary Ready Interrupt Enable */ +#define GCR_SECRES_IEN (1 << 5) /* Secondary Resume Interrupt Enable */ +#define GCR_PRIRES_IEN (1 << 4) /* Primary Resume Interrupt Enable */ +#define GCR_ACLINK_OFF (1 << 3) /* AC-link Shut Off */ +#define GCR_WARM_RST (1 << 2) /* AC97 Warm Reset */ +#define GCR_COLD_RST (1 << 1) /* AC'97 Cold Reset (0 = active) */ +#define GCR_GIE (1 << 0) /* Codec GPI Interrupt Enable */ + +#define POSR __REG(0x40500010) /* PCM Out Status Register */ +#define POSR_FIFOE (1 << 4) /* FIFO error */ +#define POSR_FSR (1 << 2) /* FIFO Service Request */ + +#define PISR __REG(0x40500014) /* PCM In Status Register */ +#define PISR_FIFOE (1 << 4) /* FIFO error */ +#define PISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */ +#define PISR_FSR (1 << 2) /* FIFO Service Request */ + +#define MCSR __REG(0x40500018) /* Mic In Status Register */ +#define MCSR_FIFOE (1 << 4) /* FIFO error */ +#define MCSR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */ +#define MCSR_FSR (1 << 2) /* FIFO Service Request */ + +#define GSR __REG(0x4050001C) /* Global Status Register */ +#define GSR_CDONE (1 << 19) /* Command Done */ +#define GSR_SDONE (1 << 18) /* Status Done */ +#define GSR_RDCS (1 << 15) /* Read Completion Status */ +#define GSR_BIT3SLT12 (1 << 14) /* Bit 3 of slot 12 */ +#define GSR_BIT2SLT12 (1 << 13) /* Bit 2 of slot 12 */ +#define GSR_BIT1SLT12 (1 << 12) /* Bit 1 of slot 12 */ +#define GSR_SECRES (1 << 11) /* Secondary Resume Interrupt */ +#define GSR_PRIRES (1 << 10) /* Primary Resume Interrupt */ +#define GSR_SCR (1 << 9) /* Secondary Codec Ready */ +#define GSR_PCR (1 << 8) /* Primary Codec Ready */ +#define GSR_MCINT (1 << 7) /* Mic In Interrupt */ +#define GSR_POINT (1 << 6) /* PCM Out Interrupt */ +#define GSR_PIINT (1 << 5) /* PCM In Interrupt */ +#define GSR_ACOFFD (1 << 3) /* AC-link Shut Off Done */ +#define GSR_MOINT (1 << 2) /* Modem Out Interrupt */ +#define GSR_MIINT (1 << 1) /* Modem In Interrupt */ +#define GSR_GSCI (1 << 0) /* Codec GPI Status Change Interrupt */ + +#define CAR __REG(0x40500020) /* CODEC Access Register */ +#define CAR_CAIP (1 << 0) /* Codec Access In Progress */ + +#define PCDR __REG(0x40500040) /* PCM FIFO Data Register */ +#define MCDR __REG(0x40500060) /* Mic-in FIFO Data Register */ + +#define MOCR __REG(0x40500100) /* Modem Out Control Register */ +#define MOCR_FEIE (1 << 3) /* FIFO Error */ +#define MOCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ + +#define MICR __REG(0x40500108) /* Modem In Control Register */ +#define MICR_FEIE (1 << 3) /* FIFO Error */ +#define MICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ + +#define MOSR __REG(0x40500110) /* Modem Out Status Register */ +#define MOSR_FIFOE (1 << 4) /* FIFO error */ +#define MOSR_FSR (1 << 2) /* FIFO Service Request */ + +#define MISR __REG(0x40500118) /* Modem In Status Register */ +#define MISR_FIFOE (1 << 4) /* FIFO error */ +#define MISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */ +#define MISR_FSR (1 << 2) /* FIFO Service Request */ + +#define MODR __REG(0x40500140) /* Modem FIFO Data Register */ + +#define PAC_REG_BASE __REG(0x40500200) /* Primary Audio Codec */ +#define SAC_REG_BASE __REG(0x40500300) /* Secondary Audio Codec */ +#define PMC_REG_BASE __REG(0x40500400) /* Primary Modem Codec */ +#define SMC_REG_BASE __REG(0x40500500) /* Secondary Modem Codec */ + +#endif /* __ASM_ARCH_REGS_AC97_H */ -- cgit v1.2.1 From f1647e4c068139b5f6c988b0862eb1d233dfffe2 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Fri, 28 Nov 2008 14:54:39 +0800 Subject: [ARM] pxa: move GPIOx_BASE and GPIO register offsets to gpio.c Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/pxa-regs.h | 28 ---------------------------- 1 file changed, 28 deletions(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/pxa-regs.h b/arch/arm/mach-pxa/include/mach/pxa-regs.h index a56502898030..782ad4ab8055 100644 --- a/arch/arm/mach-pxa/include/mach/pxa-regs.h +++ b/arch/arm/mach-pxa/include/mach/pxa-regs.h @@ -203,19 +203,6 @@ * General Purpose I/O */ -#define GPIO0_BASE ((void __iomem *)io_p2v(0x40E00000)) -#define GPIO1_BASE ((void __iomem *)io_p2v(0x40E00004)) -#define GPIO2_BASE ((void __iomem *)io_p2v(0x40E00008)) -#define GPIO3_BASE ((void __iomem *)io_p2v(0x40E00100)) - -#define GPLR_OFFSET 0x00 -#define GPDR_OFFSET 0x0C -#define GPSR_OFFSET 0x18 -#define GPCR_OFFSET 0x24 -#define GRER_OFFSET 0x30 -#define GFER_OFFSET 0x3C -#define GEDR_OFFSET 0x48 - #define GPLR0 __REG(0x40E00000) /* GPIO Pin-Level Register GPIO<31:0> */ #define GPLR1 __REG(0x40E00004) /* GPIO Pin-Level Register GPIO<63:32> */ #define GPLR2 __REG(0x40E00008) /* GPIO Pin-Level Register GPIO<80:64> */ @@ -265,10 +252,6 @@ #define GPIO_bit(x) (1 << ((x) & 0x1f)) -#if defined(CONFIG_PXA27x) || defined(CONFIG_PXA3xx) - -/* Interrupt Controller */ - #define _GPLR(x) __REG2(0x40E00000, ((x) & 0x60) >> 3) #define _GPDR(x) __REG2(0x40E0000C, ((x) & 0x60) >> 3) #define _GPSR(x) __REG2(0x40E00018, ((x) & 0x60) >> 3) @@ -287,18 +270,7 @@ #define GEDR(x) (*((((x) & 0x7f) < 96) ? &_GEDR(x) : &GEDR3)) #define GAFR(x) (*((((x) & 0x7f) < 96) ? &_GAFR(x) : \ ((((x) & 0x7f) < 112) ? &GAFR3_L : &GAFR3_U))) -#else - -#define GPLR(x) __REG2(0x40E00000, ((x) & 0x60) >> 3) -#define GPDR(x) __REG2(0x40E0000C, ((x) & 0x60) >> 3) -#define GPSR(x) __REG2(0x40E00018, ((x) & 0x60) >> 3) -#define GPCR(x) __REG2(0x40E00024, ((x) & 0x60) >> 3) -#define GRER(x) __REG2(0x40E00030, ((x) & 0x60) >> 3) -#define GFER(x) __REG2(0x40E0003C, ((x) & 0x60) >> 3) -#define GEDR(x) __REG2(0x40E00048, ((x) & 0x60) >> 3) -#define GAFR(x) __REG2(0x40E00054, ((x) & 0x70) >> 2) -#endif /* * Power Manager - see pxa2xx-regs.h -- cgit v1.2.1 From bf8b38654be05aa2e5e537a1d4353cefa1fa4b42 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Fri, 28 Nov 2008 14:57:33 +0800 Subject: [ARM] pxa: further cleanup of pxa-regs.h Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/pxa-regs.h | 29 ----------------------------- 1 file changed, 29 deletions(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/pxa-regs.h b/arch/arm/mach-pxa/include/mach/pxa-regs.h index 782ad4ab8055..ad65826dcafa 100644 --- a/arch/arm/mach-pxa/include/mach/pxa-regs.h +++ b/arch/arm/mach-pxa/include/mach/pxa-regs.h @@ -123,18 +123,6 @@ #define DCMD_WIDTH4 (3 << 14) /* 4 byte width (Word) */ #define DCMD_LENGTH 0x01fff /* length mask (max = 8K - 1) */ -/* - * I2C registers - moved into drivers/i2c/busses/i2c-pxa.c - */ - -/* - * Serial Audio Controller - moved into sound/soc/pxa/pxa2xx-i2s.c - */ - -/* - * Fast Infrared Communication Port - moved into drivers/net/irda/pxaficp_ir.c - */ - /* * Real Time Clock */ @@ -271,21 +259,4 @@ #define GAFR(x) (*((((x) & 0x7f) < 96) ? &_GAFR(x) : \ ((((x) & 0x7f) < 112) ? &GAFR3_L : &GAFR3_U))) - -/* - * Power Manager - see pxa2xx-regs.h - */ - -/* - * SSP Serial Port Registers - see arch/arm/mach-pxa/include/mach/regs-ssp.h - */ - -/* - * MultiMediaCard (MMC) controller - see drivers/mmc/host/pxamci.h - */ - -/* - * Core Clock - see arch/arm/mach-pxa/include/mach/pxa2xx-regs.h - */ - #endif -- cgit v1.2.1 From 7e5abc465b20001576d360ed2ece424da816e3a4 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Sun, 30 Nov 2008 23:13:52 +0800 Subject: [ARM] pxa: include in pxa-regs.h for the reference of __REG() within Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/pxa-regs.h | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/pxa-regs.h b/arch/arm/mach-pxa/include/mach/pxa-regs.h index ad65826dcafa..31d615aa7723 100644 --- a/arch/arm/mach-pxa/include/mach/pxa-regs.h +++ b/arch/arm/mach-pxa/include/mach/pxa-regs.h @@ -13,6 +13,7 @@ #ifndef __PXA_REGS_H #define __PXA_REGS_H +#include /* * PXA Chip selects -- cgit v1.2.1 From f1c6cd62cc4f7e55a803c4b9b92a67488d765a8f Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Wed, 26 Nov 2008 15:39:39 +0800 Subject: [ARM] pxa: introduced cpu_is_pxa935() and cpu_is_pxa9xx() Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/hardware.h | 31 ++++++++++++++++++++++++++++++- 1 file changed, 30 insertions(+), 1 deletion(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/hardware.h b/arch/arm/mach-pxa/include/mach/hardware.h index f6b4103ecc65..e2d6784aa7ef 100644 --- a/arch/arm/mach-pxa/include/mach/hardware.h +++ b/arch/arm/mach-pxa/include/mach/hardware.h @@ -102,6 +102,9 @@ * PXA930 B0 0x69056835 0x5E643013 * PXA930 B1 0x69056837 0x7E643013 * PXA930 B2 0x69056838 0x8E643013 + * + * PXA935 A0 0x56056931 0x1E653013 + * PXA935 B0 0x56056936 0x6E653013 */ #ifdef CONFIG_PXA25x #define __cpu_is_pxa210(id) \ @@ -178,12 +181,22 @@ #define __cpu_is_pxa930(id) \ ({ \ unsigned int _id = (id) >> 4 & 0xfff; \ - _id == 0x683; \ + _id == 0x683; \ }) #else #define __cpu_is_pxa930(id) (0) #endif +#ifdef CONFIG_CPU_PXA935 +#define __cpu_is_pxa935(id) \ + ({ \ + unsigned int _id = (id) >> 4 & 0xfff; \ + _id == 0x693; \ + }) +#else +#define __cpu_is_pxa935(id) (0) +#endif + #define cpu_is_pxa210() \ ({ \ __cpu_is_pxa210(read_cpuid_id()); \ @@ -230,6 +243,12 @@ __cpu_is_pxa930(id); \ }) +#define cpu_is_pxa935() \ + ({ \ + unsigned int id = read_cpuid(CPUID_ID); \ + __cpu_is_pxa935(id); \ + }) + /* * CPUID Core Generation Bit * <= 0x2 for pxa21x/pxa25x/pxa26x/pxa27x @@ -247,6 +266,12 @@ _id == 0x3; \ }) +#define __cpu_is_pxa9xx(id) \ + ({ \ + unsigned int _id = (id) >> 4 & 0xfff; \ + _id == 0x683 || _id == 0x693; \ + }) + #define cpu_is_pxa2xx() \ ({ \ __cpu_is_pxa2xx(read_cpuid_id()); \ @@ -257,6 +282,10 @@ __cpu_is_pxa3xx(read_cpuid_id()); \ }) +#define cpu_is_pxa9xx() \ + ({ \ + __cpu_is_pxa9xx(read_cpuid_id()); \ + }) /* * return current memory and LCD clock frequency in units of 10kHz */ -- cgit v1.2.1 From 8cc78909816ed5529806ee94f19f3e02beae4e7e Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Sat, 22 Nov 2008 21:40:50 +0800 Subject: [ARM] pxa: add missing GPIOs definitions GPIO3/GPIO4 are a bit special on pxa27x, since it depends on PCFR/PI2C_EN bit, add their definitions here with comments. Signed-off-by: Eric Miao Acked-by: Stefan Schmidt --- arch/arm/mach-pxa/include/mach/mfp-pxa27x.h | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h b/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h index 122bdbd53182..da4f85a4f990 100644 --- a/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h +++ b/arch/arm/mach-pxa/include/mach/mfp-pxa27x.h @@ -11,6 +11,12 @@ #include #include +/* Note: GPIO3/GPIO4 will be driven by Power I2C when PCFR/PI2C_EN + * bit is set, regardless of the GPIO configuration + */ +#define GPIO3_GPIO MFP_CFG_IN(GPIO3, AF0) +#define GPIO4_GPIO MFP_CFG_IN(GPIO4, AF0) + /* GPIO */ #define GPIO85_GPIO MFP_CFG_IN(GPIO85, AF0) #define GPIO86_GPIO MFP_CFG_IN(GPIO86, AF0) -- cgit v1.2.1 From a10c287d393bdd32127d59f3ec8fd7bb80e2fa05 Mon Sep 17 00:00:00 2001 From: Philipp Zabel Date: Sun, 29 Jun 2008 16:53:34 +0200 Subject: [ARM] pxa: cpufreq-pxa2xx: sdram_rows detection support This patch implements Eric Miao's idea to detect the correct value of sdram_rows by inspecting the MDCNFG register settings. It is only tested on two pxa27x devices with 64MB RAM (magician and hx4700) so far. Signed-off-by: Philipp Zabel Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/pxa2xx-regs.h | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h b/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h index 2b71d87c898f..77102d695cc7 100644 --- a/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h +++ b/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h @@ -49,6 +49,11 @@ #define MECR_NOS (1 << 0) /* Number Of Sockets: 0 -> 1 sock, 1 -> 2 sock */ #define MECR_CIT (1 << 1) /* Card Is There: 0 -> no card, 1 -> card inserted */ +#define MDCNFG_DE0 (1 << 0) /* SDRAM Bank 0 Enable */ +#define MDCNFG_DE1 (1 << 1) /* SDRAM Bank 1 Enable */ +#define MDCNFG_DE2 (1 << 16) /* SDRAM Bank 2 Enable */ +#define MDCNFG_DE3 (1 << 17) /* SDRAM Bank 3 Enable */ + #define MDREFR_K0DB4 (1 << 29) /* SDCLK0 Divide by 4 Control/Status */ #define MDREFR_K2FREE (1 << 25) /* SDRAM Free-Running Control */ #define MDREFR_K1FREE (1 << 24) /* SDRAM Free-Running Control */ -- cgit v1.2.1 From c96763d4dc2f4032369f068a5d185238e01da478 Mon Sep 17 00:00:00 2001 From: Robert Jarzmik Date: Tue, 18 Nov 2008 20:23:32 +0100 Subject: [ARM] pxa/MioA701: discovered new gpio definitions. The charger enable gpio is straight (1 means draw from USB Vbus, 0 mean do not draw). The USB Vbus sensing is inverted (1 means no Vbus voltage sensed, 0 means Vbus voltage present). Signed-off-by: Robert Jarzmik Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/mioa701.h | 9 +++++++-- 1 file changed, 7 insertions(+), 2 deletions(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/mioa701.h b/arch/arm/mach-pxa/include/mach/mioa701.h index 8483cb511831..02868447b0b1 100644 --- a/arch/arm/mach-pxa/include/mach/mioa701.h +++ b/arch/arm/mach-pxa/include/mach/mioa701.h @@ -10,12 +10,14 @@ (MFP_PIN(pin) | MFP_##af | MFP_DIR_OUT | MFP_LPM_##state)) /* Global GPIOs */ -#define GPIO9_CHARGE_nEN 9 +#define GPIO9_CHARGE_EN 9 #define GPIO18_POWEROFF 18 #define GPIO87_LCD_POWER 87 +#define GPIO96_AC_DETECT 96 +#define GPIO80_MAYBE_CHARGE_VDROP 80 /* Drop of 88mV */ /* USB */ -#define GPIO13_USB_DETECT 13 +#define GPIO13_nUSB_DETECT 13 #define GPIO22_USB_ENABLE 22 /* SDIO bits */ @@ -24,7 +26,10 @@ #define GPIO91_SDIO_EN 91 /* Bluetooth */ +#define GPIO14_BT_nACTIVITY 14 #define GPIO83_BT_ON 83 +#define GPIO77_BT_UNKNOWN1 77 +#define GPIO86_BT_MAYBE_nRESET 86 /* GPS */ #define GPIO23_GPS_UNKNOWN1 23 -- cgit v1.2.1 From bc2fd1c09c226ea47ab8301cde6dbcf9e5c78b73 Mon Sep 17 00:00:00 2001 From: Anton Vorontsov Date: Thu, 23 Oct 2008 21:06:56 +0200 Subject: [ARM] pxa: add basic support for HP iPAQ h5000 This patch adds HP iPAQ h5000's (h5400, h5500) basic definitions. Kernel will able to boot, work via serial console, mount filesystems placed on flashes and run USB gadgets (g_ether by default). Other device drivers (frame buffer, LCD, touchscreen, backlight, bluetooth, w1/battery, ...) are depend on SAMCOP and MediaQ SoCs/MFDs, drivers to which will be submitted too, after massive cleanups. This machine will be used as "real user" for these new drivers. This is an updated version of the patch, which contains fixes proposed on linux-arm-kernel mailing list. Signed-off-by: Anton Vorontsov Signed-off-by: Milan Plzik Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/h5000.h | 113 +++++++++++++++++++++++++++++++++ 1 file changed, 113 insertions(+) create mode 100644 arch/arm/mach-pxa/include/mach/h5000.h (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/h5000.h b/arch/arm/mach-pxa/include/mach/h5000.h new file mode 100644 index 000000000000..2a5ae3802787 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/h5000.h @@ -0,0 +1,113 @@ +/* + * Hardware definitions for HP iPAQ h5xxx Handheld Computers + * + * Copyright(20)02 Hewlett-Packard Company. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * COMPAQ COMPUTER CORPORATION MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, + * AS TO THE USEFULNESS OR CORRECTNESS OF THIS CODE OR ITS + * FITNESS FOR ANY PARTICULAR PURPOSE. + * + * Author: Jamey Hicks + */ + +#ifndef __ASM_ARCH_H5000_H +#define __ASM_ARCH_H5000_H + +#include + +/* + * CPU GPIOs + */ + +#define H5000_GPIO_POWER_BUTTON (0) +#define H5000_GPIO_RESET_BUTTON_N (1) +#define H5000_GPIO_OPT_INT (2) +#define H5000_GPIO_BACKUP_POWER (3) +#define H5000_GPIO_ACTION_BUTTON (4) +#define H5000_GPIO_COM_DCD_SOMETHING (5) /* what is this really ? */ +/* 6 not connected */ +#define H5000_GPIO_RESET_BUTTON_AGAIN_N (7) /* connected to gpio 1 as well */ +/* 8 not connected */ +#define H5000_GPIO_RSO_N (9) /* reset output from max1702 which regulates 3.3 and 2.5 */ +#define H5000_GPIO_ASIC_INT_N (10) /* from companion asic */ +#define H5000_GPIO_BT_ENV_0 (11) /* to LMX9814, set to 1 according to regdump */ +/*(12) not connected */ +#define H5000_GPIO_BT_ENV_1 (13) /* to LMX9814, set to 1 according to regdump */ +#define H5000_GPIO_BT_WU (14) /* from LMX9814, Defined as HOST_WAKEUP in the LMX9820 data sheet */ +/*(15) is CS1# */ +/*(16) not connected */ +/*(17) not connected */ +/*(18) is pcmcia ready */ +/*(19) is dreq1 */ +/*(20) is dreq0 */ +#define H5000_GPIO_OE_RD_NWR (21) /* output enable on rd/nwr signal to companion asic */ +/*(22) is not connected */ +#define H5000_GPIO_OPT_SPI_CLK (23) /* to extension pack */ +#define H5000_GPIO_OPT_SPI_CS_N (24) /* to extension pack */ +#define H5000_GPIO_OPT_SPI_DOUT (25) /* to extension pack */ +#define H5000_GPIO_OPT_SPI_DIN (26) /* to extension pack */ +/*(27) not connected */ +#define H5000_GPIO_I2S_BITCLK (28) /* connected to AC97 codec */ +#define H5000_GPIO_I2S_DATAOUT (29) /* connected to AC97 codec */ +#define H5000_GPIO_I2S_DATAIN (30) /* connected to AC97 codec */ +#define H5000_GPIO_I2S_LRCLK (31) /* connected to AC97 codec */ +#define H5000_GPIO_I2S_SYSCLK (32) /* connected to AC97 codec */ +/*(33) is CS5# */ +#define H5000_GPIO_COM_RXD (34) /* connected to cradle/cable connector */ +#define H5000_GPIO_COM_CTS (35) /* connected to cradle/cable connector */ +#define H5000_GPIO_COM_DCD (36) /* connected to cradle/cable connector */ +#define H5000_GPIO_COM_DSR (37) /* connected to cradle/cable connector */ +#define H5000_GPIO_COM_RI (38) /* connected to cradle/cable connector */ +#define H5000_GPIO_COM_TXD (39) /* connected to cradle/cable connector */ +#define H5000_GPIO_COM_DTR (40) /* connected to cradle/cable connector */ +#define H5000_GPIO_COM_RTS (41) /* connected to cradle/cable connector */ + +#define H5000_GPIO_BT_RXD (42) /* connected to BT (LMX9814) */ +#define H5000_GPIO_BT_TXD (43) /* connected to BT (LMX9814) */ +#define H5000_GPIO_BT_CTS (44) /* connected to BT (LMX9814) */ +#define H5000_GPIO_BT_RTS (45) /* connected to BT (LMX9814) */ + +#define H5000_GPIO_IRDA_RXD (46) +#define H5000_GPIO_IRDA_TXD (47) + +#define H5000_GPIO_POE_N (48) /* used for pcmcia */ +#define H5000_GPIO_PWE_N (49) /* used for pcmcia */ +#define H5000_GPIO_PIOR_N (50) /* used for pcmcia */ +#define H5000_GPIO_PIOW_N (51) /* used for pcmcia */ +#define H5000_GPIO_PCE1_N (52) /* used for pcmcia */ +#define H5000_GPIO_PCE2_N (53) /* used for pcmcia */ +#define H5000_GPIO_PSKTSEL (54) /* used for pcmcia */ +#define H5000_GPIO_PREG_N (55) /* used for pcmcia */ +#define H5000_GPIO_PWAIT_N (56) /* used for pcmcia */ +#define H5000_GPIO_IOIS16_N (57) /* used for pcmcia */ + +#define H5000_GPIO_IRDA_SD (58) /* to hsdl3002 sd */ +/*(59) not connected */ +#define H5000_GPIO_POWER_SD_N (60) /* controls power to SD */ +#define H5000_GPIO_POWER_RS232_N (61) /* inverted FORCEON to rs232 transceiver */ +#define H5000_GPIO_POWER_ACCEL_N (62) /* controls power to accel */ +/*(63) is not connected */ +#define H5000_GPIO_OPT_NVRAM (64) /* controls power to expansion pack */ +#define H5000_GPIO_CHG_EN (65) /* to sc801 en */ +#define H5000_GPIO_USB_PULLUP (66) /* USB d+ pullup via 1.5K resistor */ +#define H5000_GPIO_BT_2V8_N (67) /* 2.8V used by bluetooth */ +#define H5000_GPIO_EXT_CHG_RATE (68) /* enables external charging rate */ +/*(69) is not connected */ +#define H5000_GPIO_CIR_RESET (70) /* consumer IR reset */ +#define H5000_GPIO_POWER_LIGHT_SENSOR_N (71) +#define H5000_GPIO_BT_M_RESET (72) +#define H5000_GPIO_STD_CHG_RATE (73) +#define H5000_GPIO_SD_WP_N (74) +#define H5000_GPIO_MOTOR_ON_N (75) /* external pullup on this */ +#define H5000_GPIO_HEADPHONE_DETECT (76) +#define H5000_GPIO_USB_CHG_RATE (77) /* select rate for charging via usb */ +/*(78) is CS2# */ +/*(79) is CS3# */ +/*(80) is CS4# */ + +#endif /* __ASM_ARCH_H5000_H */ -- cgit v1.2.1 From 67fbc2312312095acc2f19a0b601bac10f84cf9d Mon Sep 17 00:00:00 2001 From: Russell King Date: Thu, 11 Dec 2008 17:20:44 +0000 Subject: [ARM] fix xm_x2xx_defconfig build errors drivers/built-in.o: In function `pci_set_consistent_dma_mask': hid-quirks.c:(.text+0x2664): multiple definition of `pci_set_consistent_dma_mask' drivers/built-in.o: In function `pci_set_dma_mask': hid-quirks.c:(.text+0x42c4): multiple definition of `pci_set_dma_mask' because drivers/pci/pci.c was not seeing the definition disabling these functions. Signed-off-by: Russell King --- arch/arm/mach-pxa/include/mach/dma.h | 4 ---- arch/arm/mach-pxa/include/mach/hardware.h | 2 ++ 2 files changed, 2 insertions(+), 4 deletions(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/dma.h b/arch/arm/mach-pxa/include/mach/dma.h index 955bfe606067..7804637a6df3 100644 --- a/arch/arm/mach-pxa/include/mach/dma.h +++ b/arch/arm/mach-pxa/include/mach/dma.h @@ -30,10 +30,6 @@ typedef enum { DMA_PRIO_LOW = 2 } pxa_dma_prio; -#if defined(CONFIG_MACH_ARMCORE) && defined(CONFIG_PCI) -#define HAVE_ARCH_PCI_SET_DMA_MASK 1 -#endif - /* * DMA registration */ diff --git a/arch/arm/mach-pxa/include/mach/hardware.h b/arch/arm/mach-pxa/include/mach/hardware.h index e2d6784aa7ef..4e782ec38668 100644 --- a/arch/arm/mach-pxa/include/mach/hardware.h +++ b/arch/arm/mach-pxa/include/mach/hardware.h @@ -297,6 +297,8 @@ extern unsigned int get_memclk_frequency_10khz(void); #define PCIBIOS_MIN_IO 0 #define PCIBIOS_MIN_MEM 0 #define pcibios_assign_all_busses() 1 +#define HAVE_ARCH_PCI_SET_DMA_MASK 1 #endif + #endif /* _ASM_ARCH_HARDWARE_H */ -- cgit v1.2.1 From a02f45cfca97dcf97c03b32603ec2399bf006605 Mon Sep 17 00:00:00 2001 From: Russell King Date: Sun, 14 Dec 2008 13:22:51 +0000 Subject: [ARM] move asm/xip.h's mach/hardware.h include to mach/xip.h Signed-off-by: Russell King --- arch/arm/mach-pxa/include/mach/mtd-xip.h | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/mtd-xip.h b/arch/arm/mach-pxa/include/mach/mtd-xip.h index 4d452fcb1508..cfca8155be72 100644 --- a/arch/arm/mach-pxa/include/mach/mtd-xip.h +++ b/arch/arm/mach-pxa/include/mach/mtd-xip.h @@ -15,6 +15,7 @@ #ifndef __ARCH_PXA_MTD_XIP_H__ #define __ARCH_PXA_MTD_XIP_H__ +#include #include #define xip_irqpending() (ICIP & ICMR) -- cgit v1.2.1 From b1ae1b7b274f67c149bee4731e38a7516c723de4 Mon Sep 17 00:00:00 2001 From: Ian Molton Date: Fri, 26 Sep 2008 13:38:59 +0100 Subject: [ARM] pxa: Add multi-io support for e-series This patchset provides support for the TMIO based IO controller used in the Toshiba e-series PDAs. Signed-off-by: Ian Molton Acked-by: Samuel Ortiz Acked-by: Eric Miao --- arch/arm/mach-pxa/include/mach/eseries-gpio.h | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/eseries-gpio.h b/arch/arm/mach-pxa/include/mach/eseries-gpio.h index 794bc338b4df..efbd2aa9ecec 100644 --- a/arch/arm/mach-pxa/include/mach/eseries-gpio.h +++ b/arch/arm/mach-pxa/include/mach/eseries-gpio.h @@ -47,4 +47,6 @@ /* ASIC related GPIOs */ #define GPIO_ESERIES_TMIO_IRQ 5 +#define GPIO_ESERIES_TMIO_PCLR 19 +#define GPIO_ESERIES_TMIO_SUSPEND 45 #define GPIO_E800_ANGELX_IRQ 8 -- cgit v1.2.1 From 51633048890ca755bce2411e13a2f84ec661a068 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Sun, 7 Dec 2008 17:48:00 +0800 Subject: [ARM] pxafb: add color TFT 8BPP LCD panel type Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/pxafb.h | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/pxafb.h b/arch/arm/mach-pxa/include/mach/pxafb.h index cbda4d35c421..cb44410cd456 100644 --- a/arch/arm/mach-pxa/include/mach/pxafb.h +++ b/arch/arm/mach-pxa/include/mach/pxafb.h @@ -48,6 +48,7 @@ #define LCD_MONO_DSTN_8BPP ((8 << 4) | LCD_TYPE_MONO_DSTN) #define LCD_COLOR_STN_8BPP ((8 << 4) | LCD_TYPE_COLOR_STN) #define LCD_COLOR_DSTN_16BPP ((16 << 4) | LCD_TYPE_COLOR_DSTN) +#define LCD_COLOR_TFT_8BPP ((8 << 4) | LCD_TYPE_COLOR_TFT) #define LCD_COLOR_TFT_16BPP ((16 << 4) | LCD_TYPE_COLOR_TFT) #define LCD_COLOR_TFT_18BPP ((18 << 4) | LCD_TYPE_COLOR_TFT) #define LCD_SMART_PANEL_8BPP ((8 << 4) | LCD_TYPE_SMART_PANEL) -- cgit v1.2.1 From c1f99c215c58111629984a49ba87b2b145dd1f5b Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Mon, 8 Dec 2008 18:35:03 +0800 Subject: [ARM] pxafb: allow better platform configurable smart panel timing For smart panels (LCD panel with internal framebuffer), the following LCCR3 register bits have different meanings than the parallel one: LCCR3_PCP - controls the L_PCLK_WR polarity LCCR3_HSP - controls the L_LCLK_A0 polarity LCCR3_VSP - controls the L_FCLK_RD polarity To keep minimum change to the original parallel timing, the .lcd_conn flags and 'pxafb_mode_info.sync' are re-used to reflect this: LCD_PCLK_EDGE_{RISE,FALL} - configures LCCR3_PCP sync & FB_SYNC_{HOR,VERT}_HIGH_ACT - configures LCCR3_{HSP,VSP} Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/pxafb.h | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/pxafb.h b/arch/arm/mach-pxa/include/mach/pxafb.h index cb44410cd456..4201a889ff4e 100644 --- a/arch/arm/mach-pxa/include/mach/pxafb.h +++ b/arch/arm/mach-pxa/include/mach/pxafb.h @@ -95,6 +95,10 @@ struct pxafb_mode_info { * in pxa27x and pxa3xx, initialize them to the same value or * the larger one will be used * 3. same to {rd,wr}_pulse_width + * + * 4. LCD_PCLK_EDGE_{RISE,FALL} controls the L_PCLK_WR polarity + * 5. sync & FB_SYNC_HOR_HIGH_ACT controls the L_LCLK_A0 + * 6. sync & FB_SYNC_VERT_HIGH_ACT controls the L_LCLK_RD */ unsigned a0csrd_set_hld; /* A0 and CS Setup/Hold Time before/after L_FCLK_RD */ unsigned a0cswr_set_hld; /* A0 and CS Setup/Hold Time before/after L_PCLK_WR */ -- cgit v1.2.1 From 69bdea7047fbac88beb8b7ba9e428c4f0e53f563 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Mon, 8 Dec 2008 18:46:00 +0800 Subject: [ARM] pxafb: allow insertion of delay to the smart panel command sequence Some smart panel requires a delay between command sequences, while PXA LCD controller didn't provide such one, let's emulate this by software. A software delay marker can be inserted into the command sequence, once pxafb_smart_queue() detects this, it flushes the previous commands and delay for a specified number of milliseconds. Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/regs-lcd.h | 7 +++++++ 1 file changed, 7 insertions(+) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/regs-lcd.h b/arch/arm/mach-pxa/include/mach/regs-lcd.h index c689c4ea769c..f817878d256b 100644 --- a/arch/arm/mach-pxa/include/mach/regs-lcd.h +++ b/arch/arm/mach-pxa/include/mach/regs-lcd.h @@ -177,4 +177,11 @@ #define SMART_CMD(x) (SMART_CMD_WRITE_COMMAND | ((x) & 0xff)) #define SMART_DAT(x) (SMART_CMD_WRITE_DATA | ((x) & 0xff)) + +/* SMART_DELAY() is introduced for software controlled delay primitive which + * can be inserted between command sequences, unused command 0x6 is used here + * and delay ranges from 0ms ~ 255ms + */ +#define SMART_CMD_DELAY (0x6 << 9) +#define SMART_DELAY(ms) (SMART_CMD_DELAY | ((ms) & 0xff)) #endif /* __ASM_ARCH_REGS_LCD_H */ -- cgit v1.2.1 From 3332b0c17969d91d8868d2d003e685c420d84262 Mon Sep 17 00:00:00 2001 From: Jaya Kumar Date: Tue, 9 Dec 2008 22:14:29 +0800 Subject: [ARM] pxa/gumstix: fix incorrect init done by am200 Signed-off-by: Jaya Kumar Cc: Andre Puschmann Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/gumstix.h | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/gumstix.h b/arch/arm/mach-pxa/include/mach/gumstix.h index 42ee1956750e..099f54a41de4 100644 --- a/arch/arm/mach-pxa/include/mach/gumstix.h +++ b/arch/arm/mach-pxa/include/mach/gumstix.h @@ -94,3 +94,7 @@ has detected a cable insertion; driven low otherwise. */ #define GPIO26_PRDY_nBSY_MD (GPIO26_PRDY_nBSY | GPIO_IN) #define GPIO27_PRDY_nBSY_MD (GPIO27_PRDY_nBSY | GPIO_IN) #define GPIO36_nCD_MD (GPIO36_nCD | GPIO_IN) + +/* for expansion boards that can't be programatically detected */ +extern int am200_init(void); + -- cgit v1.2.1 From b6795fa9fd70bc4cd94724c32fe1945e5c75c29f Mon Sep 17 00:00:00 2001 From: Jonathan Cameron Date: Fri, 12 Dec 2008 20:43:09 +0000 Subject: [ARM] pxa: initial support for the Imote2 platform Changes made as suggested by Eric Miao (including fix to map_io silly mistake!). Originally designed by Intel, now sold by Crossbow (www.xbow.com). Very little actually on board. The patch includes sensors and similar as found on commonly occurring daughter boards. Some of the drivers are not in mainline as yet as they are either part of the IIO subsystem or need a lot of work before submission. What is the position wrt to putting them in i2c board configs etc? Support for these boards has been maintained outside the kernel for a long time, but now that there is a good da9030 pmic driver available the last major hurdle no longer exists. All comments welcomed. The Imote2's big brother (stargate2) will follow once any problems with this one have been cleaned up and a few bits and bobs have been added to the da903x driver. Hopefully the cc2420 driver will get cleaned up and submitted in the not too distant future as well. Signed-off-by: Jonathan Cameron Acked-by: Mark Brown Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/uncompress.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/uncompress.h b/arch/arm/mach-pxa/include/mach/uncompress.h index a9a4f302b6ef..f4b029c03957 100644 --- a/arch/arm/mach-pxa/include/mach/uncompress.h +++ b/arch/arm/mach-pxa/include/mach/uncompress.h @@ -35,7 +35,7 @@ static inline void flush(void) static inline void arch_decomp_setup(void) { - if (machine_is_littleton()) + if (machine_is_littleton() || machine_is_intelmote2()) UART = STUART; } -- cgit v1.2.1 From 3b24f30c4f678cfab5c6d090af9559fefa37cc41 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Wed, 10 Dec 2008 17:04:38 +0800 Subject: [ARM] pxa/littleton: add preliminary I2C board info (da9034 + max7320) Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/littleton.h | 11 ++++++++--- 1 file changed, 8 insertions(+), 3 deletions(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/littleton.h b/arch/arm/mach-pxa/include/mach/littleton.h index 5c4e320c1437..6c9b21c51322 100644 --- a/arch/arm/mach-pxa/include/mach/littleton.h +++ b/arch/arm/mach-pxa/include/mach/littleton.h @@ -1,8 +1,13 @@ -#ifndef __ASM_ARCH_ZYLONITE_H -#define __ASM_ARCH_ZYLONITE_H +#ifndef __ASM_ARCH_LITTLETON_H +#define __ASM_ARCH_LITTLETON_H + +#include #define LITTLETON_ETH_PHYS 0x30000000 #define LITTLETON_GPIO_LCD_CS (17) -#endif /* __ASM_ARCH_ZYLONITE_H */ +#define EXT0_GPIO_BASE (NR_BUILTIN_GPIO) +#define EXT0_GPIO(x) (EXT0_GPIO_BASE + (x)) + +#endif /* __ASM_ARCH_LITTLETON_H */ -- cgit v1.2.1 From 9f1442bbf9fd68d8e190c91ab294131dd5c289ee Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Sun, 28 Dec 2008 00:40:29 +0800 Subject: [ARM] pxa/tavorevb: update board support (smartpanel LCD + keypad) Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/mfp-pxa930.h | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/mfp-pxa930.h b/arch/arm/mach-pxa/include/mach/mfp-pxa930.h index fabd9b4df827..fa73f56a1372 100644 --- a/arch/arm/mach-pxa/include/mach/mfp-pxa930.h +++ b/arch/arm/mach-pxa/include/mach/mfp-pxa930.h @@ -421,6 +421,7 @@ #define GPIO20_PWM0 MFP_CFG_LPM(GPIO20, AF2, PULL_LOW) #define GPIO21_PWM2 MFP_CFG_LPM(GPIO21, AF3, PULL_LOW) #define GPIO22_PWM3 MFP_CFG_LPM(GPIO22, AF3, PULL_LOW) +#define GPIO32_PWM0 MFP_CFG_LPM(GPIO32, AF4, PULL_LOW) /* CIR */ #define GPIO46_CIR_OUT MFP_CFG(GPIO46, AF1) -- cgit v1.2.1 From 6769717d5d51596618f6b143008d8ace11ec8a69 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Thu, 18 Dec 2008 11:10:32 +0800 Subject: [ARM] rtc-sa1100: don't assume CLOCK_TICK_RATE to be a constant As Nicolas and Russell pointed out, CLOCK_TICK_RATE is no more a constant on PXA when multiple processors and platforms are selected, change TIMER_FREQ in rtc-sa1100.c into a variable. Since the code to decide the clock tick rate is re-used from timer.c, introduce a common get_clock_tick_rate() for this. Signed-off-by: Eric Miao Acked-by: Nicolas Pitre --- arch/arm/mach-pxa/include/mach/hardware.h | 2 ++ arch/arm/mach-pxa/include/mach/timex.h | 8 ++++++++ 2 files changed, 10 insertions(+) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/hardware.h b/arch/arm/mach-pxa/include/mach/hardware.h index e2d6784aa7ef..c666796911cb 100644 --- a/arch/arm/mach-pxa/include/mach/hardware.h +++ b/arch/arm/mach-pxa/include/mach/hardware.h @@ -291,6 +291,8 @@ */ extern unsigned int get_memclk_frequency_10khz(void); +/* return the clock tick rate of the OS timer */ +extern unsigned long get_clock_tick_rate(void); #endif #if defined(CONFIG_MACH_ARMCORE) && defined(CONFIG_PCI) diff --git a/arch/arm/mach-pxa/include/mach/timex.h b/arch/arm/mach-pxa/include/mach/timex.h index b05fc6683c47..af6760a50e1a 100644 --- a/arch/arm/mach-pxa/include/mach/timex.h +++ b/arch/arm/mach-pxa/include/mach/timex.h @@ -10,6 +10,14 @@ * published by the Free Software Foundation. */ +/* Various drivers are still using the constant of CLOCK_TICK_RATE, for + * those drivers to at least work, the definition is provided here. + * + * NOTE: this is no longer accurate when multiple processors and boards + * are selected, newer drivers should not depend on this any more. Use + * either the clocksource/clockevent or get this at run-time by calling + * get_clock_tick_rate() (as defined in generic.c). + */ #if defined(CONFIG_PXA25x) /* PXA250/210 timer base */ -- cgit v1.2.1 From 77e196752bdd76a0c58ab082658d28c6a90fa40e Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Tue, 16 Dec 2008 11:54:34 +0800 Subject: [ARM] pxafb: allow video memory size to be configurable The amount of video memory size is decided according to the following order: 1. x x by default, which is the backward compatible way 2. size specified in platform data 3. size specified in module parameter 'options' string or specified in kernel boot command line (see updated Documentation/fb/pxafb.txt) And now since the memory is allocated from system memory, the pxafb_mmap can be removed and the default fb_mmap() should be working all right. Also, since we now have introduced the 'struct pxafb_dma_buff' for DMA descriptors and palettes, the allocation can be separated cleanly. NOTE: the LCD DMA actually supports chained transfer (i.e. page-based transfers), to simplify the logic and keep the performance (with less TLB misses when accessing from memory mapped user space), the memory is allocated by alloc_pages_*() to ensures it's physical contiguous. Signed-off-by: Eric Miao Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/pxafb.h | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/pxafb.h b/arch/arm/mach-pxa/include/mach/pxafb.h index 4201a889ff4e..6932720ba04e 100644 --- a/arch/arm/mach-pxa/include/mach/pxafb.h +++ b/arch/arm/mach-pxa/include/mach/pxafb.h @@ -113,6 +113,7 @@ struct pxafb_mach_info { unsigned int num_modes; unsigned int lcd_conn; + unsigned long video_mem_size; u_int fixed_modes:1, cmap_inverse:1, -- cgit v1.2.1 From 6e354846e807e037751fdc8faaee8ad492177113 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Wed, 17 Dec 2008 16:50:43 +0800 Subject: [ARM] pxafb: add support for FBIOPAN_DISPLAY by dma braching dma branching is enabled by extending the current setup_frame_dma() function to allow a 2nd set of frame/palette dma descriptors to be used. As a result, pxafb_dma_buff.dma_desc[], pxafb_dma_buff.pal_desc[] and pxafb_info.fdadr[] are doubled. This allows maximum re-use of the current dma setup code, although the pxafb_info.fdadr[xx] for FBRx register values looks a bit odd. Signed-off-by: Eric Miao Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/regs-lcd.h | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/regs-lcd.h b/arch/arm/mach-pxa/include/mach/regs-lcd.h index f817878d256b..c15df557fa8a 100644 --- a/arch/arm/mach-pxa/include/mach/regs-lcd.h +++ b/arch/arm/mach-pxa/include/mach/regs-lcd.h @@ -12,13 +12,19 @@ #define LCCR3 (0x00C) /* LCD Controller Control Register 3 */ #define LCCR4 (0x010) /* LCD Controller Control Register 4 */ #define LCCR5 (0x014) /* LCD Controller Control Register 5 */ -#define DFBR0 (0x020) /* DMA Channel 0 Frame Branch Register */ -#define DFBR1 (0x024) /* DMA Channel 1 Frame Branch Register */ #define LCSR (0x038) /* LCD Controller Status Register */ #define LIIDR (0x03C) /* LCD Controller Interrupt ID Register */ #define TMEDRGBR (0x040) /* TMED RGB Seed Register */ #define TMEDCR (0x044) /* TMED Control Register */ +#define FBR0 (0x020) /* DMA Channel 0 Frame Branch Register */ +#define FBR1 (0x024) /* DMA Channel 1 Frame Branch Register */ +#define FBR2 (0x028) /* DMA Channel 2 Frame Branch Register */ +#define FBR3 (0x02C) /* DMA Channel 2 Frame Branch Register */ +#define FBR4 (0x030) /* DMA Channel 2 Frame Branch Register */ +#define FBR5 (0x110) /* DMA Channel 2 Frame Branch Register */ +#define FBR6 (0x114) /* DMA Channel 2 Frame Branch Register */ + #define CMDCR (0x100) /* Command Control Register */ #define PRSR (0x104) /* Panel Read Status Register */ -- cgit v1.2.1 From a0427509a76c61984fbba4e206b617c689f419ef Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Thu, 18 Dec 2008 22:10:00 +0800 Subject: [ARM] pxafb: add palette format support for LCCR4_PAL_FOR_3 Add the palette format support for LCCR4_PAL_FOR_3, and fix the issue of LCCR4 being never assigned. Also remove the useless pxafb_set_truecolor(). Signed-off-by: Eric Miao Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/regs-lcd.h | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/regs-lcd.h b/arch/arm/mach-pxa/include/mach/regs-lcd.h index c15df557fa8a..5c522263e401 100644 --- a/arch/arm/mach-pxa/include/mach/regs-lcd.h +++ b/arch/arm/mach-pxa/include/mach/regs-lcd.h @@ -48,6 +48,7 @@ #define LCCR4_PAL_FOR_0 (0 << 15) #define LCCR4_PAL_FOR_1 (1 << 15) #define LCCR4_PAL_FOR_2 (2 << 15) +#define LCCR4_PAL_FOR_3 (3 << 15) #define LCCR4_PAL_FOR_MASK (3 << 15) #define FDADR0 (0x200) /* DMA Channel 0 Frame Descriptor Address Register */ -- cgit v1.2.1 From 878f5783199a95cfa91db45a6e34d2f72756fa18 Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Thu, 18 Dec 2008 22:36:26 +0800 Subject: [ARM] pxafb: cleanup of the color format manipulation code 1. introduce var_to_depth() to calculate the color depth including the transparency bit 2. the conversion from 'fb_var_screeninfo' to LCCR3 BPP bits can be re- used by overlays (in OVLxC1), thus an individual pxafb_var_to_bpp() has been separated out. 3. pxafb_setmode() should really set the color bitfields correctly at begining, introduce a pxafb_set_pixfmt() for this 4. allow user apps to specify color formats within fb_var_screeninfo, and checking of this in pxafb_check_var() has been simplified as below: a) pxafb_var_to_bpp() should pass - which means a basically correct bits_per_pixel and color depth setting b) the RGBT bitfields are then forced into supported values by pxafb_set_pixfmt() Signed-off-by: Eric Miao Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/regs-lcd.h | 15 +-------------- 1 file changed, 1 insertion(+), 14 deletions(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/regs-lcd.h b/arch/arm/mach-pxa/include/mach/regs-lcd.h index 5c522263e401..aff3b876a7bf 100644 --- a/arch/arm/mach-pxa/include/mach/regs-lcd.h +++ b/arch/arm/mach-pxa/include/mach/regs-lcd.h @@ -28,17 +28,7 @@ #define CMDCR (0x100) /* Command Control Register */ #define PRSR (0x104) /* Panel Read Status Register */ -#define LCCR3_1BPP (0 << 24) -#define LCCR3_2BPP (1 << 24) -#define LCCR3_4BPP (2 << 24) -#define LCCR3_8BPP (3 << 24) -#define LCCR3_16BPP (4 << 24) -#define LCCR3_18BPP (5 << 24) -#define LCCR3_18BPP_P (6 << 24) -#define LCCR3_19BPP (7 << 24) -#define LCCR3_19BPP_P (1 << 29) -#define LCCR3_24BPP ((1 << 29) | (1 << 24)) -#define LCCR3_25BPP ((1 << 29) | (2 << 24)) +#define LCCR3_BPP(x) ((((x) & 0x7) << 24) | (((x) & 0x8) ? (1 << 29) : 0)) #define LCCR3_PDFOR_0 (0 << 30) #define LCCR3_PDFOR_1 (1 << 30) @@ -133,9 +123,6 @@ #define LCCR3_PCD Fld (8, 0) /* Pixel Clock Divisor */ #define LCCR3_PixClkDiv(Div) (((Div) << FShft (LCCR3_PCD))) -#define LCCR3_BPP Fld (3, 24) /* Bit Per Pixel */ -#define LCCR3_Bpp(Bpp) (((Bpp) << FShft (LCCR3_BPP))) - #define LCCR3_ACB Fld (8, 8) /* AC Bias */ #define LCCR3_Acb(Acb) (((Acb) << FShft (LCCR3_ACB))) -- cgit v1.2.1 From 198fc108ee4c2cd3f08954eae6a819c81c03214b Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Tue, 23 Dec 2008 17:49:43 +0800 Subject: [ARM] pxafb: add support for overlay1 and overlay2 as framebuffer devices PXA27x and later processors support overlay1 and overlay2 on-top of the base framebuffer (although under-neath the base is also possible). They support palette and no-palette RGB formats, as well as YUV formats (only available on overlay2). These overlays have dedicated DMA channels and behave in a similar way as a framebuffer. This heavily simplified and re-structured work is based on the original pxafb_overlay.c (which is pending for mainline merge for a long time). The major problems with this pxafb_overlay.c are (if you are interested in the history): 1. heavily redundant (the control logics for overlay1 and overlay2 are actually identical except for some small operations, which are now abstracted into a 'pxafb_layer_ops' structure) 2. a lot of useless and un-tested code (two workarounds which are now fixed on mature silicons) 3. cursorfb is actually useless, hardware cursor should not be used this way, and the code was actually un-tested for a long time. The code in this patch should be self-explanatory, I tried to add minimum comments. As said, this is basically simplified, there are several things still on the pending list: 1. palette mode is un-supported and un-tested (although re-using the palette code of the base framebuffer is actually very easy now with previous clean-up patches) 2. fb_pan_display for overlay(s) is un-supported 3. the base framebuffer can actually be abstracted by 'pxafb_layer' as well, which will help further re-use of the code and keep a better and consistent structure. (This is the reason I named it 'pxafb_layer' instead of 'pxafb_overlay' or something alike) See Documentation/fb/pxafb.txt for additional usage information. Signed-off-by: Eric Miao Cc: Rodolfo Giometti Signed-off-by: Eric Miao --- arch/arm/mach-pxa/include/mach/regs-lcd.h | 34 +++++++++++++++++++++++-------- 1 file changed, 25 insertions(+), 9 deletions(-) (limited to 'arch/arm/mach-pxa/include') diff --git a/arch/arm/mach-pxa/include/mach/regs-lcd.h b/arch/arm/mach-pxa/include/mach/regs-lcd.h index aff3b876a7bf..f82dcea792d9 100644 --- a/arch/arm/mach-pxa/include/mach/regs-lcd.h +++ b/arch/arm/mach-pxa/include/mach/regs-lcd.h @@ -12,7 +12,8 @@ #define LCCR3 (0x00C) /* LCD Controller Control Register 3 */ #define LCCR4 (0x010) /* LCD Controller Control Register 4 */ #define LCCR5 (0x014) /* LCD Controller Control Register 5 */ -#define LCSR (0x038) /* LCD Controller Status Register */ +#define LCSR (0x038) /* LCD Controller Status Register 0 */ +#define LCSR1 (0x034) /* LCD Controller Status Register 1 */ #define LIIDR (0x03C) /* LCD Controller Interrupt ID Register */ #define TMEDRGBR (0x040) /* TMED RGB Seed Register */ #define TMEDCR (0x044) /* TMED Control Register */ @@ -25,6 +26,11 @@ #define FBR5 (0x110) /* DMA Channel 2 Frame Branch Register */ #define FBR6 (0x114) /* DMA Channel 2 Frame Branch Register */ +#define OVL1C1 (0x050) /* Overlay 1 Control Register 1 */ +#define OVL1C2 (0x060) /* Overlay 1 Control Register 2 */ +#define OVL2C1 (0x070) /* Overlay 2 Control Register 1 */ +#define OVL2C2 (0x080) /* Overlay 2 Control Register 2 */ + #define CMDCR (0x100) /* Command Control Register */ #define PRSR (0x104) /* Panel Read Status Register */ @@ -42,16 +48,12 @@ #define LCCR4_PAL_FOR_MASK (3 << 15) #define FDADR0 (0x200) /* DMA Channel 0 Frame Descriptor Address Register */ -#define FSADR0 (0x204) /* DMA Channel 0 Frame Source Address Register */ -#define FIDR0 (0x208) /* DMA Channel 0 Frame ID Register */ -#define LDCMD0 (0x20C) /* DMA Channel 0 Command Register */ #define FDADR1 (0x210) /* DMA Channel 1 Frame Descriptor Address Register */ -#define FSADR1 (0x214) /* DMA Channel 1 Frame Source Address Register */ -#define FIDR1 (0x218) /* DMA Channel 1 Frame ID Register */ -#define LDCMD1 (0x21C) /* DMA Channel 1 Command Register */ +#define FDADR2 (0x220) /* DMA Channel 2 Frame Descriptor Address Register */ +#define FDADR3 (0x230) /* DMA Channel 3 Frame Descriptor Address Register */ +#define FDADR4 (0x240) /* DMA Channel 4 Frame Descriptor Address Register */ +#define FDADR5 (0x250) /* DMA Channel 5 Frame Descriptor Address Register */ #define FDADR6 (0x260) /* DMA Channel 6 Frame Descriptor Address Register */ -#define FSADR6 (0x264) /* DMA Channel 6 Frame Source Address Register */ -#define FIDR6 (0x268) /* DMA Channel 6 Frame ID Register */ #define LCCR0_ENB (1 << 0) /* LCD Controller enable */ #define LCCR0_CMS (1 << 1) /* Color/Monochrome Display Select */ @@ -151,8 +153,22 @@ #define LCSR_RD_ST (1 << 11) /* read status */ #define LCSR_CMD_INT (1 << 12) /* command interrupt */ +#define LCSR1_IU(x) (1 << ((x) + 23)) /* Input FIFO underrun */ +#define LCSR1_BS(x) (1 << ((x) + 15)) /* Branch Status */ +#define LCSR1_EOF(x) (1 << ((x) + 7)) /* End of Frame Status */ +#define LCSR1_SOF(x) (1 << ((x) - 1)) /* Start of Frame Status */ + #define LDCMD_PAL (1 << 26) /* instructs DMA to load palette buffer */ +/* overlay control registers */ +#define OVLxC1_PPL(x) ((((x) - 1) & 0x3ff) << 0) /* Pixels Per Line */ +#define OVLxC1_LPO(x) ((((x) - 1) & 0x3ff) << 10) /* Number of Lines */ +#define OVLxC1_BPP(x) (((x) & 0xf) << 20) /* Bits Per Pixel */ +#define OVLxC1_OEN (1 << 31) /* Enable bit for Overlay */ +#define OVLxC2_XPOS(x) (((x) & 0x3ff) << 0) /* Horizontal Position */ +#define OVLxC2_YPOS(x) (((x) & 0x3ff) << 10) /* Vertical Position */ +#define OVL2C2_PFOR(x) (((x) & 0x7) << 20) /* Pixel Format */ + /* smartpanel related */ #define PRSR_DATA(x) ((x) & 0xff) /* Panel Data */ #define PRSR_A0 (1 << 8) /* Read Data Source */ -- cgit v1.2.1