From db549d22c4b84824f90558eb8e6b116cf134794d Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Mon, 28 Jun 2010 17:16:38 +0530 Subject: davinci: da850 evm: sparse cleanup: make file local variables static Without this cleanup, sparse checker reports warnings of the type: CHECK arch/arm/mach-davinci/board-da850-evm.c arch/arm/mach-davinci/board-da850-evm.c:112:22: warning: symbol 'da850_evm_nandflash_partition' was not declared. Should it be static? The nand flash partitions and regulator supplies are used within the EVM file and so should have been static This patch has been boot tested on DA830 and DA850 EVMs. Signed-off-by: Sekhar Nori Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/board-da850-evm.c | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c index fdc2cc500fc6..711a56a4c963 100644 --- a/arch/arm/mach-davinci/board-da850-evm.c +++ b/arch/arm/mach-davinci/board-da850-evm.c @@ -110,7 +110,7 @@ static struct platform_device da850_pm_device = { * to boot, using TI's tools to install the secondary boot loader * (UBL) and U-Boot. */ -struct mtd_partition da850_evm_nandflash_partition[] = { +static struct mtd_partition da850_evm_nandflash_partition[] = { { .name = "u-boot env", .offset = 0, @@ -406,7 +406,7 @@ static int da850_lcd_hw_init(void) /* TPS65070 voltage regulator support */ /* 3.3V */ -struct regulator_consumer_supply tps65070_dcdc1_consumers[] = { +static struct regulator_consumer_supply tps65070_dcdc1_consumers[] = { { .supply = "usb0_vdda33", }, @@ -416,7 +416,7 @@ struct regulator_consumer_supply tps65070_dcdc1_consumers[] = { }; /* 3.3V or 1.8V */ -struct regulator_consumer_supply tps65070_dcdc2_consumers[] = { +static struct regulator_consumer_supply tps65070_dcdc2_consumers[] = { { .supply = "dvdd3318_a", }, @@ -429,14 +429,14 @@ struct regulator_consumer_supply tps65070_dcdc2_consumers[] = { }; /* 1.2V */ -struct regulator_consumer_supply tps65070_dcdc3_consumers[] = { +static struct regulator_consumer_supply tps65070_dcdc3_consumers[] = { { .supply = "cvdd", }, }; /* 1.8V LDO */ -struct regulator_consumer_supply tps65070_ldo1_consumers[] = { +static struct regulator_consumer_supply tps65070_ldo1_consumers[] = { { .supply = "sata_vddr", }, @@ -452,7 +452,7 @@ struct regulator_consumer_supply tps65070_ldo1_consumers[] = { }; /* 1.2V LDO */ -struct regulator_consumer_supply tps65070_ldo2_consumers[] = { +static struct regulator_consumer_supply tps65070_ldo2_consumers[] = { { .supply = "sata_vdd", }, @@ -475,7 +475,7 @@ static struct tps6507x_reg_platform_data tps6507x_platform_data = { .defdcdc_default = true, }; -struct regulator_init_data tps65070_regulator_data[] = { +static struct regulator_init_data tps65070_regulator_data[] = { /* dcdc1 */ { .constraints = { -- cgit v1.2.1 From c89f1681450822c74afb3217ed4c24a177a23f43 Mon Sep 17 00:00:00 2001 From: Kevin Hilman Date: Thu, 5 Aug 2010 10:55:16 -0700 Subject: davinci: clock: make 'disable unused clocks' printk debug only The long list of clocks being disabled on boot is noisy and not needed for standard boots. Make this a debug printk instead. Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/clock.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/clock.c b/arch/arm/mach-davinci/clock.c index 054c303caead..5b0cb62a058f 100644 --- a/arch/arm/mach-davinci/clock.c +++ b/arch/arm/mach-davinci/clock.c @@ -236,7 +236,7 @@ static int __init clk_disable_unused(void) if (!davinci_psc_is_clk_active(ck->gpsc, ck->lpsc)) continue; - pr_info("Clocks: disable unused %s\n", ck->name); + pr_debug("Clocks: disable unused %s\n", ck->name); davinci_psc_config(psc_domain(ck), ck->gpsc, ck->lpsc, (ck->flags & PSC_SWRSTDISABLE) ? -- cgit v1.2.1 From fca97b3337edb6b12707d167460b224dd8ef6052 Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Tue, 20 Jul 2010 16:46:48 +0530 Subject: davinci: cpufreq: bailout on regulator errors Current cpufreq code does not consider errors that can occur while changing voltage. Code to increase CPU frequency goes ahead even in the case the regulator has failed to increase the voltage. This leads to hard error since lower voltages cannot support increased frequency. Prevent this by not increasing frequency in case increasing voltage is not successful. Also, do not lower the voltage if changing the cpu frequency has failed for some reason. Note that we do not return error on failure to decrease voltage as that is not a hard error. Build fix for non-cpufreq kernels by Caglar Akyuz. Signed-off-by: Sekhar Nori Cc: Caglar Akyuz Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/cpufreq.c | 10 ++++++++-- arch/arm/mach-davinci/da850.c | 2 +- 2 files changed, 9 insertions(+), 3 deletions(-) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/cpufreq.c b/arch/arm/mach-davinci/cpufreq.c index d3fa6de1e20f..bc8014279114 100644 --- a/arch/arm/mach-davinci/cpufreq.c +++ b/arch/arm/mach-davinci/cpufreq.c @@ -104,15 +104,21 @@ static int davinci_target(struct cpufreq_policy *policy, cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE); /* if moving to higher frequency, up the voltage beforehand */ - if (pdata->set_voltage && freqs.new > freqs.old) - pdata->set_voltage(idx); + if (pdata->set_voltage && freqs.new > freqs.old) { + ret = pdata->set_voltage(idx); + if (ret) + goto out; + } ret = clk_set_rate(armclk, idx); + if (ret) + goto out; /* if moving to lower freq, lower the voltage after lowering freq */ if (pdata->set_voltage && freqs.new < freqs.old) pdata->set_voltage(idx); +out: cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE); return ret; diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c index 68ed58a48252..868227e66cea 100644 --- a/arch/arm/mach-davinci/da850.c +++ b/arch/arm/mach-davinci/da850.c @@ -983,7 +983,7 @@ static int da850_set_pll0rate(struct clk *clk, unsigned long index) return 0; } #else -int __init da850_register_cpufreq(void) +int __init da850_register_cpufreq(char *async_clk) { return 0; } -- cgit v1.2.1 From a7884f454b75ac57e92b8c3fb3b20148f92f7688 Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Thu, 1 Jul 2010 19:00:49 +0530 Subject: davinci: clean up inconsistent usage of spaces in Kconfig In arch/arm/mach-davinci/Kconfig, some of the configuration items are indented with multiple spaces instead of tabs. Also, in couple of places, two spaces are used in the middle of help text where one should do. This patch fixes both issues. Signed-off-by: Sekhar Nori Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/Kconfig | 32 ++++++++++++++++---------------- 1 file changed, 16 insertions(+), 16 deletions(-) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig index 71f90f864748..b291da1da069 100644 --- a/arch/arm/mach-davinci/Kconfig +++ b/arch/arm/mach-davinci/Kconfig @@ -20,17 +20,17 @@ config ARCH_DAVINCI_DM644x select ARCH_DAVINCI_DMx config ARCH_DAVINCI_DM355 - bool "DaVinci 355 based system" + bool "DaVinci 355 based system" select AINTC select ARCH_DAVINCI_DMx config ARCH_DAVINCI_DM646x - bool "DaVinci 646x based system" + bool "DaVinci 646x based system" select AINTC select ARCH_DAVINCI_DMx config ARCH_DAVINCI_DA830 - bool "DA830/OMAP-L137 based system" + bool "DA830/OMAP-L137 based system" select CP_INTC select ARCH_DAVINCI_DA8XX select CPU_DCACHE_WRITETHROUGH # needed on silicon revs 1.0, 1.1 @@ -140,7 +140,7 @@ config DA830_UI_LCD config DA830_UI_NAND bool "NAND flash" help - Say Y here to use the NAND flash. Do not forget to setup + Say Y here to use the NAND flash. Do not forget to setup the switch correctly. endchoice @@ -195,20 +195,20 @@ config DAVINCI_MUX say Y. config DAVINCI_MUX_DEBUG - bool "Multiplexing debug output" - depends on DAVINCI_MUX - help - Makes the multiplexing functions print out a lot of debug info. - This is useful if you want to find out the correct values of the - multiplexing registers. + bool "Multiplexing debug output" + depends on DAVINCI_MUX + help + Makes the multiplexing functions print out a lot of debug info. + This is useful if you want to find out the correct values of the + multiplexing registers. config DAVINCI_MUX_WARNINGS - bool "Warn about pins the bootloader didn't set up" - depends on DAVINCI_MUX - help - Choose Y here to warn whenever driver initialization logic needs - to change the pin multiplexing setup. When there are no warnings - printed, it's safe to deselect DAVINCI_MUX for your product. + bool "Warn about pins the bootloader didn't set up" + depends on DAVINCI_MUX + help + Choose Y here to warn whenever driver initialization logic needs + to change the pin multiplexing setup. When there are no warnings + printed, it's safe to deselect DAVINCI_MUX for your product. config DAVINCI_RESET_CLOCKS bool "Reset unused clocks during boot" -- cgit v1.2.1 From 48ea89eabee96019a4a84615af921f8703320abb Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Thu, 1 Jul 2010 19:00:50 +0530 Subject: davinci: introduce support for AM1x ARM9 microprocessors The Sitara AM17x SoCs from TI are an OMAP-L137 pin-to-pin compatible ARM9 microprocessor offering from TI. The Sitara AM18x SoCs from TI are an OMAP-L138 pin-to-pin compatible ARM9 microprocessor offering from TI. More information about these processors available at: www.ti.com/am1x Because of their compatibiliy with OMAP-L1x, the kernel support for OMAP-L1x is fully relevant to AM1x processors. This patch updates the Kconfig prompt and help text to include the AM1x part names to help users select configurations required for these parts easily. Also, the hardware information that shows up in /proc/cpuinfo is updated to show applicability of the respective OMAP-L1x EVMs for AM1x parts. Signed-off-by: Sekhar Nori Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/Kconfig | 30 +++++++++++++++--------------- arch/arm/mach-davinci/board-da830-evm.c | 2 +- arch/arm/mach-davinci/board-da850-evm.c | 2 +- 3 files changed, 17 insertions(+), 17 deletions(-) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig index b291da1da069..2bf03e95505f 100644 --- a/arch/arm/mach-davinci/Kconfig +++ b/arch/arm/mach-davinci/Kconfig @@ -30,13 +30,13 @@ config ARCH_DAVINCI_DM646x select ARCH_DAVINCI_DMx config ARCH_DAVINCI_DA830 - bool "DA830/OMAP-L137 based system" + bool "DA830/OMAP-L137/AM17x based system" select CP_INTC select ARCH_DAVINCI_DA8XX select CPU_DCACHE_WRITETHROUGH # needed on silicon revs 1.0, 1.1 config ARCH_DAVINCI_DA850 - bool "DA850/OMAP-L138 based system" + bool "DA850/OMAP-L138/AM18x based system" select CP_INTC select ARCH_DAVINCI_DA8XX select ARCH_HAS_CPUFREQ @@ -115,21 +115,21 @@ config MACH_DAVINCI_DM365_EVM for development is a DM365 EVM config MACH_DAVINCI_DA830_EVM - bool "TI DA830/OMAP-L137 Reference Platform" + bool "TI DA830/OMAP-L137/AM17x Reference Platform" default ARCH_DAVINCI_DA830 depends on ARCH_DAVINCI_DA830 select GPIO_PCF857X help - Say Y here to select the TI DA830/OMAP-L137 Evaluation Module. + Say Y here to select the TI DA830/OMAP-L137/AM17x Evaluation Module. choice - prompt "Select DA830/OMAP-L137 UI board peripheral" + prompt "Select DA830/OMAP-L137/AM17x UI board peripheral" depends on MACH_DAVINCI_DA830_EVM help - The presence of UI card on the DA830/OMAP-L137 EVM is detected - automatically based on successful probe of the I2C based GPIO - expander on that board. This option selected in this menu has - an effect only in case of a successful UI card detection. + The presence of UI card on the DA830/OMAP-L137/AM17x EVM is + detected automatically based on successful probe of the I2C + based GPIO expander on that board. This option selected in this + menu has an effect only in case of a successful UI card detection. config DA830_UI_LCD bool "LCD" @@ -145,18 +145,18 @@ config DA830_UI_NAND endchoice config MACH_DAVINCI_DA850_EVM - bool "TI DA850/OMAP-L138 Reference Platform" + bool "TI DA850/OMAP-L138/AM18x Reference Platform" default ARCH_DAVINCI_DA850 depends on ARCH_DAVINCI_DA850 select GPIO_PCA953X help - Say Y here to select the TI DA850/OMAP-L138 Evaluation Module. + Say Y here to select the TI DA850/OMAP-L138/AM18x Evaluation Module. choice prompt "Select peripherals connected to expander on UI board" depends on MACH_DAVINCI_DA850_EVM help - The presence of User Interface (UI) card on the DA850/OMAP-L138 + The presence of User Interface (UI) card on the DA850/OMAP-L138/AM18x EVM is detected automatically based on successful probe of the I2C based GPIO expander on that card. This option selected in this menu has an effect only in case of a successful UI card detection. @@ -165,13 +165,13 @@ config DA850_UI_NONE bool "No peripheral is enabled" help Say Y if you do not want to enable any of the peripherals connected - to TCA6416 expander on DA850/OMAP-L138 EVM UI card + to TCA6416 expander on DA850/OMAP-L138/AM18x EVM UI card config DA850_UI_RMII bool "RMII Ethernet PHY" help - Say Y if you want to use the RMII PHY on the DA850/OMAP-L138 EVM. - This PHY is found on the UI daughter card that is supplied with + Say Y if you want to use the RMII PHY on the DA850/OMAP-L138/AM18x + EVM. This PHY is found on the UI daughter card that is supplied with the EVM. NOTE: Please take care while choosing this option, MII PHY will not be functional if RMII mode is selected. diff --git a/arch/arm/mach-davinci/board-da830-evm.c b/arch/arm/mach-davinci/board-da830-evm.c index c3994f341e49..292e8b7c02ac 100644 --- a/arch/arm/mach-davinci/board-da830-evm.c +++ b/arch/arm/mach-davinci/board-da830-evm.c @@ -596,7 +596,7 @@ static void __init da830_evm_map_io(void) da830_init(); } -MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP-L137 EVM") +MACHINE_START(DAVINCI_DA830_EVM, "DaVinci DA830/OMAP-L137/AM17x EVM") .phys_io = IO_PHYS, .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc, .boot_params = (DA8XX_DDR_BASE + 0x100), diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c index 711a56a4c963..f5f947257011 100644 --- a/arch/arm/mach-davinci/board-da850-evm.c +++ b/arch/arm/mach-davinci/board-da850-evm.c @@ -816,7 +816,7 @@ static void __init da850_evm_map_io(void) da850_init(); } -MACHINE_START(DAVINCI_DA850_EVM, "DaVinci DA850/OMAP-L138 EVM") +MACHINE_START(DAVINCI_DA850_EVM, "DaVinci DA850/OMAP-L138/AM18x EVM") .phys_io = IO_PHYS, .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc, .boot_params = (DA8XX_DDR_BASE + 0x100), -- cgit v1.2.1 From 6ef62f8204402e32259451857c1a4a04f155b56e Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Wed, 7 Jul 2010 14:02:49 +0530 Subject: davinci: am18x/da850/omap-l138: use 'NOM' voltage defined in datasheet as min voltage For each DA850 OPP, the normal ('NOM') voltage defined in the tecnical reference manual (TRM) is actually the minimum voltage the frequency is supported at. The minimum ('MIN') voltage defined in TRM is meant to take care of voltage fluctuations and the device should not be run at this voltage for extended periods of time. Fix the OPP definitions to define the cvdd_min as the normal voltage defined in the datasheet. Signed-off-by: Sekhar Nori Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/da850.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c index 868227e66cea..6932d804556b 100644 --- a/arch/arm/mach-davinci/da850.c +++ b/arch/arm/mach-davinci/da850.c @@ -851,7 +851,7 @@ static const struct da850_opp da850_opp_300 = { .prediv = 1, .mult = 25, .postdiv = 2, - .cvdd_min = 1140000, + .cvdd_min = 1200000, .cvdd_max = 1320000, }; @@ -860,7 +860,7 @@ static const struct da850_opp da850_opp_200 = { .prediv = 1, .mult = 25, .postdiv = 3, - .cvdd_min = 1050000, + .cvdd_min = 1100000, .cvdd_max = 1160000, }; @@ -869,7 +869,7 @@ static const struct da850_opp da850_opp_96 = { .prediv = 1, .mult = 20, .postdiv = 5, - .cvdd_min = 950000, + .cvdd_min = 1000000, .cvdd_max = 1050000, }; -- cgit v1.2.1 From 0a477f6b8c1849701981f6e00e7afcd35af75546 Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Wed, 14 Jul 2010 17:09:45 +0530 Subject: davinci: dm365: disable pulldowns for all MMC/SD1 pins. This patch disables internal pulldowns for all MMC/SD1 pins. Presently only MMCSD1_CMD pin's pull down is disabled, but with this some MMC/SD cards do not get detected on MMC/SD1 slot of the EVM. The problem was reproducible with SanDisk 4GB SDHC card. Reported-by: Stephane Bovagne Signed-off-by: Sekhar Nori Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/devices.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/devices.c b/arch/arm/mach-davinci/devices.c index 8b7201e4c79c..2a9a252327d8 100644 --- a/arch/arm/mach-davinci/devices.c +++ b/arch/arm/mach-davinci/devices.c @@ -213,7 +213,7 @@ void __init davinci_setup_mmc(int module, struct davinci_mmc_config *config) IO_ADDRESS(DAVINCI_SYSTEM_MODULE_BASE + 0x7c); /* Configure pull down control */ - __raw_writel((__raw_readl(pupdctl1) & ~0x400), + __raw_writel((__raw_readl(pupdctl1) & ~0xfc0), pupdctl1); mmcsd1_resources[0].start = DM365_MMCSD1_BASE; -- cgit v1.2.1 From b39639b820ca64e55c39b5217773919ca7973cec Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Tue, 20 Jul 2010 16:46:49 +0530 Subject: davinci: clock: add support for setting sysclk rate Setting sysclk rate will be useful in cases where the sysclk is not at a fixed ratio to the PLL output but can asynchronously be changed. This support forms the basis of attempt to keep the AEMIF clock constant on OMAP-L138 even as PLL0 output changes as ARM clock is changed to save power. This patch has been tested on OMAP-L138. Signed-off-by: Sekhar Nori Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/clock.c | 73 +++++++++++++++++++++++++++++++++++++++++++ arch/arm/mach-davinci/clock.h | 5 +++ 2 files changed, 78 insertions(+) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/clock.c b/arch/arm/mach-davinci/clock.c index 5b0cb62a058f..01ba080433db 100644 --- a/arch/arm/mach-davinci/clock.c +++ b/arch/arm/mach-davinci/clock.c @@ -287,6 +287,79 @@ static unsigned long clk_sysclk_recalc(struct clk *clk) return rate; } +int davinci_set_sysclk_rate(struct clk *clk, unsigned long rate) +{ + unsigned v; + struct pll_data *pll; + unsigned long input; + unsigned ratio = 0; + + /* If this is the PLL base clock, wrong function to call */ + if (clk->pll_data) + return -EINVAL; + + /* There must be a parent... */ + if (WARN_ON(!clk->parent)) + return -EINVAL; + + /* ... the parent must be a PLL... */ + if (WARN_ON(!clk->parent->pll_data)) + return -EINVAL; + + /* ... and this clock must have a divider. */ + if (WARN_ON(!clk->div_reg)) + return -EINVAL; + + pll = clk->parent->pll_data; + + input = clk->parent->rate; + + /* If pre-PLL, source clock is before the multiplier and divider(s) */ + if (clk->flags & PRE_PLL) + input = pll->input_rate; + + if (input > rate) { + /* + * Can afford to provide an output little higher than requested + * only if maximum rate supported by hardware on this sysclk + * is known. + */ + if (clk->maxrate) { + ratio = DIV_ROUND_CLOSEST(input, rate); + if (input / ratio > clk->maxrate) + ratio = 0; + } + + if (ratio == 0) + ratio = DIV_ROUND_UP(input, rate); + + ratio--; + } + + if (ratio > PLLDIV_RATIO_MASK) + return -EINVAL; + + do { + v = __raw_readl(pll->base + PLLSTAT); + } while (v & PLLSTAT_GOSTAT); + + v = __raw_readl(pll->base + clk->div_reg); + v &= ~PLLDIV_RATIO_MASK; + v |= ratio | PLLDIV_EN; + __raw_writel(v, pll->base + clk->div_reg); + + v = __raw_readl(pll->base + PLLCMD); + v |= PLLCMD_GOSET; + __raw_writel(v, pll->base + PLLCMD); + + do { + v = __raw_readl(pll->base + PLLSTAT); + } while (v & PLLSTAT_GOSTAT); + + return 0; +} +EXPORT_SYMBOL(davinci_set_sysclk_rate); + static unsigned long clk_leafclk_recalc(struct clk *clk) { if (WARN_ON(!clk->parent)) diff --git a/arch/arm/mach-davinci/clock.h b/arch/arm/mach-davinci/clock.h index 01e36483ac3d..11099980b58b 100644 --- a/arch/arm/mach-davinci/clock.h +++ b/arch/arm/mach-davinci/clock.h @@ -70,6 +70,9 @@ #include #include +#define PLLSTAT_GOSTAT BIT(0) +#define PLLCMD_GOSET BIT(0) + struct pll_data { u32 phys_base; void __iomem *base; @@ -86,6 +89,7 @@ struct clk { struct module *owner; const char *name; unsigned long rate; + unsigned long maxrate; /* H/W supported max rate */ u8 usecount; u8 lpsc; u8 gpsc; @@ -118,6 +122,7 @@ struct clk { int davinci_clk_init(struct clk_lookup *clocks); int davinci_set_pllrate(struct pll_data *pll, unsigned int prediv, unsigned int mult, unsigned int postdiv); +int davinci_set_sysclk_rate(struct clk *clk, unsigned long rate); extern struct platform_device davinci_wdt_device; extern void davinci_watchdog_reset(struct platform_device *); -- cgit v1.2.1 From 30a2c5d2f0134df6175af26ce554aacaee304280 Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Tue, 20 Jul 2010 16:46:50 +0530 Subject: davinci: cpufreq: add support for keeping an additional clock constant On OMAP-L138 SoC, some of the sysclks need not be at a fixed ratio to CPU clock and can be kept at a relatively constant rate by adjusting the PLLDIVn ratio even as cpufreq goes ahead and changes the CPU clock. This feature can be used to keep the EMIFA (PLL0 SYSCLK3) clock at a constant rate so that the EMIF timings need not be re-programmed whenever the CPU frequency changes. This patch adds the required suppport to cpufreq driver. Signed-off-by: Sekhar Nori Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/cpufreq.c | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/cpufreq.c b/arch/arm/mach-davinci/cpufreq.c index bc8014279114..343de73161fa 100644 --- a/arch/arm/mach-davinci/cpufreq.c +++ b/arch/arm/mach-davinci/cpufreq.c @@ -34,6 +34,8 @@ struct davinci_cpufreq { struct device *dev; struct clk *armclk; + struct clk *asyncclk; + unsigned long asyncrate; }; static struct davinci_cpufreq cpufreq; @@ -114,6 +116,12 @@ static int davinci_target(struct cpufreq_policy *policy, if (ret) goto out; + if (cpufreq.asyncclk) { + ret = clk_set_rate(cpufreq.asyncclk, cpufreq.asyncrate); + if (ret) + goto out; + } + /* if moving to lower freq, lower the voltage after lowering freq */ if (pdata->set_voltage && freqs.new < freqs.old) pdata->set_voltage(idx); @@ -191,6 +199,7 @@ static struct cpufreq_driver davinci_driver = { static int __init davinci_cpufreq_probe(struct platform_device *pdev) { struct davinci_cpufreq_config *pdata = pdev->dev.platform_data; + struct clk *asyncclk; if (!pdata) return -EINVAL; @@ -205,6 +214,12 @@ static int __init davinci_cpufreq_probe(struct platform_device *pdev) return PTR_ERR(cpufreq.armclk); } + asyncclk = clk_get(cpufreq.dev, "async"); + if (!IS_ERR(asyncclk)) { + cpufreq.asyncclk = asyncclk; + cpufreq.asyncrate = clk_get_rate(asyncclk); + } + return cpufreq_register_driver(&davinci_driver); } @@ -212,6 +227,9 @@ static int __exit davinci_cpufreq_remove(struct platform_device *pdev) { clk_put(cpufreq.armclk); + if (cpufreq.asyncclk) + clk_put(cpufreq.asyncclk); + return cpufreq_unregister_driver(&davinci_driver); } -- cgit v1.2.1 From b987c4b2c9c9db2393f4c089e63d1734301214e5 Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Tue, 20 Jul 2010 16:46:51 +0530 Subject: davinci: am18x/da850/omap-l138: keep async clock constant with cpufreq Keep PLL0 SYSCLK3 at a constant rate of 100MHz. This enables the AEMIF timing to remain valid even as the PLL0 output is changed by cpufreq driver to save power. Signed-off-by: Sekhar Nori Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/board-da850-evm.c | 2 +- arch/arm/mach-davinci/da850.c | 10 +++++++++- arch/arm/mach-davinci/include/mach/da8xx.h | 2 +- 3 files changed, 11 insertions(+), 3 deletions(-) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c index f5f947257011..c2800a98c49d 100644 --- a/arch/arm/mach-davinci/board-da850-evm.c +++ b/arch/arm/mach-davinci/board-da850-evm.c @@ -787,7 +787,7 @@ static __init void da850_evm_init(void) if (ret) pr_warning("da850_evm_init: rtc setup failed: %d\n", ret); - ret = da850_register_cpufreq(); + ret = da850_register_cpufreq("pll0_sysclk3"); if (ret) pr_warning("da850_evm_init: cpufreq registration failed: %d\n", ret); diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c index 6932d804556b..5af7cfb1447e 100644 --- a/arch/arm/mach-davinci/da850.c +++ b/arch/arm/mach-davinci/da850.c @@ -86,6 +86,8 @@ static struct clk pll0_sysclk3 = { .parent = &pll0_clk, .flags = CLK_PLL, .div_reg = PLLDIV3, + .set_rate = davinci_set_sysclk_rate, + .maxrate = 100000000, }; static struct clk pll0_sysclk4 = { @@ -929,10 +931,16 @@ static struct platform_device da850_cpufreq_device = { .dev = { .platform_data = &cpufreq_info, }, + .id = -1, }; -int __init da850_register_cpufreq(void) +int __init da850_register_cpufreq(char *async_clk) { + /* cpufreq driver can help keep an "async" clock constant */ + if (async_clk) + clk_add_alias("async", da850_cpufreq_device.name, + async_clk, NULL); + return platform_device_register(&da850_cpufreq_device); } diff --git a/arch/arm/mach-davinci/include/mach/da8xx.h b/arch/arm/mach-davinci/include/mach/da8xx.h index 3c07059f526e..2c3f41897c17 100644 --- a/arch/arm/mach-davinci/include/mach/da8xx.h +++ b/arch/arm/mach-davinci/include/mach/da8xx.h @@ -78,7 +78,7 @@ int da8xx_register_lcdc(struct da8xx_lcdc_platform_data *pdata); int da8xx_register_mmcsd0(struct davinci_mmc_config *config); void __init da8xx_register_mcasp(int id, struct snd_platform_data *pdata); int da8xx_register_rtc(void); -int da850_register_cpufreq(void); +int da850_register_cpufreq(char *async_clk); int da8xx_register_cpuidle(void); void __iomem * __init da8xx_get_mem_ctlr(void); int da850_register_pm(struct platform_device *pdev); -- cgit v1.2.1 From 7173d5493799944d47317d9490365a89ee079f2a Mon Sep 17 00:00:00 2001 From: Cyril Chemparathy Date: Tue, 3 Aug 2010 21:04:16 -0400 Subject: Davinci: tnetv107x: retain psc reg base after init This is a bugfix for the original tnetv107x submission series. The psc_regs base array was being discarded post-init, and this was causing a crash during post-init clock enable/disable. Signed-off-by: Cyril Chemparathy Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/tnetv107x.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/tnetv107x.c b/arch/arm/mach-davinci/tnetv107x.c index 864e60482c53..06d2ac9dcf3d 100644 --- a/arch/arm/mach-davinci/tnetv107x.c +++ b/arch/arm/mach-davinci/tnetv107x.c @@ -104,7 +104,7 @@ static u32 pll_ext_freq[] = { }; /* PSC control registers */ -static u32 psc_regs[] __initconst = { TNETV107X_PSC_BASE }; +static u32 psc_regs[] = { TNETV107X_PSC_BASE }; /* Host map for interrupt controller */ static u32 intc_host_map[] = { 0x01010000, 0x01010101, -1 }; -- cgit v1.2.1 From f48ecc2f73763e9d94d5847692ed25ab0f4fb73c Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Sun, 1 Aug 2010 21:15:16 +0400 Subject: DA850: move NAND/NOR pin lists to the board file The NAND/NOR flash pin lists (da850_nand_pins/da850_nor_pins) are purely board specific and as such shouldn't be in da850.c -- copy them to board-da850-evm.c, renaming to da850_evm_nand_pins/da850_evm_nor_pins respectively, and merge the two lists in da850.c into one, representing the EMIF 2.5 module as a whole, just like we have it in da830.c... While at it, remove the '__init' modifier from da850_evm_setup_nor_nand() as this function is called from non '__init' code... Signed-off-by: Sergei Shtylyov Tested-by: Ben Gardiner Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/board-da850-evm.c | 30 +++++++++++++++++++++++++--- arch/arm/mach-davinci/da850.c | 32 +++++++++++------------------- arch/arm/mach-davinci/include/mach/da8xx.h | 3 +-- 3 files changed, 40 insertions(+), 25 deletions(-) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c index c2800a98c49d..482d4584eaa0 100644 --- a/arch/arm/mach-davinci/board-da850-evm.c +++ b/arch/arm/mach-davinci/board-da850-evm.c @@ -196,6 +196,30 @@ static void __init da850_evm_init_nor(void) iounmap(aemif_addr); } +static const short da850_evm_nand_pins[] = { + DA850_EMA_D_0, DA850_EMA_D_1, DA850_EMA_D_2, DA850_EMA_D_3, + DA850_EMA_D_4, DA850_EMA_D_5, DA850_EMA_D_6, DA850_EMA_D_7, + DA850_EMA_A_1, DA850_EMA_A_2, DA850_NEMA_CS_3, DA850_NEMA_CS_4, + DA850_NEMA_WE, DA850_NEMA_OE, + -1 +}; + +static const short da850_evm_nor_pins[] = { + DA850_EMA_BA_1, DA850_EMA_CLK, DA850_EMA_WAIT_1, DA850_NEMA_CS_2, + DA850_NEMA_WE, DA850_NEMA_OE, DA850_EMA_D_0, DA850_EMA_D_1, + DA850_EMA_D_2, DA850_EMA_D_3, DA850_EMA_D_4, DA850_EMA_D_5, + DA850_EMA_D_6, DA850_EMA_D_7, DA850_EMA_D_8, DA850_EMA_D_9, + DA850_EMA_D_10, DA850_EMA_D_11, DA850_EMA_D_12, DA850_EMA_D_13, + DA850_EMA_D_14, DA850_EMA_D_15, DA850_EMA_A_0, DA850_EMA_A_1, + DA850_EMA_A_2, DA850_EMA_A_3, DA850_EMA_A_4, DA850_EMA_A_5, + DA850_EMA_A_6, DA850_EMA_A_7, DA850_EMA_A_8, DA850_EMA_A_9, + DA850_EMA_A_10, DA850_EMA_A_11, DA850_EMA_A_12, DA850_EMA_A_13, + DA850_EMA_A_14, DA850_EMA_A_15, DA850_EMA_A_16, DA850_EMA_A_17, + DA850_EMA_A_18, DA850_EMA_A_19, DA850_EMA_A_20, DA850_EMA_A_21, + DA850_EMA_A_22, DA850_EMA_A_23, + -1 +}; + static u32 ui_card_detected; #if defined(CONFIG_MMC_DAVINCI) || \ @@ -205,17 +229,17 @@ static u32 ui_card_detected; #define HAS_MMC 0 #endif -static __init void da850_evm_setup_nor_nand(void) +static inline void da850_evm_setup_nor_nand(void) { int ret = 0; if (ui_card_detected & !HAS_MMC) { - ret = davinci_cfg_reg_list(da850_nand_pins); + ret = davinci_cfg_reg_list(da850_evm_nand_pins); if (ret) pr_warning("da850_evm_init: nand mux setup failed: " "%d\n", ret); - ret = davinci_cfg_reg_list(da850_nor_pins); + ret = davinci_cfg_reg_list(da850_evm_nor_pins); if (ret) pr_warning("da850_evm_init: nor mux setup failed: %d\n", ret); diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c index 5af7cfb1447e..efb904ebce9c 100644 --- a/arch/arm/mach-davinci/da850.c +++ b/arch/arm/mach-davinci/da850.c @@ -609,27 +609,19 @@ const short da850_mmcsd0_pins[] __initdata = { -1 }; -const short da850_nand_pins[] __initdata = { - DA850_EMA_D_7, DA850_EMA_D_6, DA850_EMA_D_5, DA850_EMA_D_4, - DA850_EMA_D_3, DA850_EMA_D_2, DA850_EMA_D_1, DA850_EMA_D_0, - DA850_EMA_A_1, DA850_EMA_A_2, DA850_NEMA_CS_3, DA850_NEMA_CS_4, - DA850_NEMA_WE, DA850_NEMA_OE, - -1 -}; - -const short da850_nor_pins[] __initdata = { +const short da850_emif25_pins[] __initdata = { DA850_EMA_BA_1, DA850_EMA_CLK, DA850_EMA_WAIT_1, DA850_NEMA_CS_2, - DA850_NEMA_WE, DA850_NEMA_OE, DA850_EMA_D_0, DA850_EMA_D_1, - DA850_EMA_D_2, DA850_EMA_D_3, DA850_EMA_D_4, DA850_EMA_D_5, - DA850_EMA_D_6, DA850_EMA_D_7, DA850_EMA_D_8, DA850_EMA_D_9, - DA850_EMA_D_10, DA850_EMA_D_11, DA850_EMA_D_12, DA850_EMA_D_13, - DA850_EMA_D_14, DA850_EMA_D_15, DA850_EMA_A_0, DA850_EMA_A_1, - DA850_EMA_A_2, DA850_EMA_A_3, DA850_EMA_A_4, DA850_EMA_A_5, - DA850_EMA_A_6, DA850_EMA_A_7, DA850_EMA_A_8, DA850_EMA_A_9, - DA850_EMA_A_10, DA850_EMA_A_11, DA850_EMA_A_12, DA850_EMA_A_13, - DA850_EMA_A_14, DA850_EMA_A_15, DA850_EMA_A_16, DA850_EMA_A_17, - DA850_EMA_A_18, DA850_EMA_A_19, DA850_EMA_A_20, DA850_EMA_A_21, - DA850_EMA_A_22, DA850_EMA_A_23, + DA850_NEMA_CS_3, DA850_NEMA_CS_4, DA850_NEMA_WE, DA850_NEMA_OE, + DA850_EMA_D_0, DA850_EMA_D_1, DA850_EMA_D_2, DA850_EMA_D_3, + DA850_EMA_D_4, DA850_EMA_D_5, DA850_EMA_D_6, DA850_EMA_D_7, + DA850_EMA_D_8, DA850_EMA_D_9, DA850_EMA_D_10, DA850_EMA_D_11, + DA850_EMA_D_12, DA850_EMA_D_13, DA850_EMA_D_14, DA850_EMA_D_15, + DA850_EMA_A_0, DA850_EMA_A_1, DA850_EMA_A_2, DA850_EMA_A_3, + DA850_EMA_A_4, DA850_EMA_A_5, DA850_EMA_A_6, DA850_EMA_A_7, + DA850_EMA_A_8, DA850_EMA_A_9, DA850_EMA_A_10, DA850_EMA_A_11, + DA850_EMA_A_12, DA850_EMA_A_13, DA850_EMA_A_14, DA850_EMA_A_15, + DA850_EMA_A_16, DA850_EMA_A_17, DA850_EMA_A_18, DA850_EMA_A_19, + DA850_EMA_A_20, DA850_EMA_A_21, DA850_EMA_A_22, DA850_EMA_A_23, -1 }; diff --git a/arch/arm/mach-davinci/include/mach/da8xx.h b/arch/arm/mach-davinci/include/mach/da8xx.h index 2c3f41897c17..8de2dbbf6fea 100644 --- a/arch/arm/mach-davinci/include/mach/da8xx.h +++ b/arch/arm/mach-davinci/include/mach/da8xx.h @@ -125,7 +125,6 @@ extern const short da850_rmii_pins[]; extern const short da850_mcasp_pins[]; extern const short da850_lcdcntl_pins[]; extern const short da850_mmcsd0_pins[]; -extern const short da850_nand_pins[]; -extern const short da850_nor_pins[]; +extern const short da850_emif25_pins[]; #endif /* __ASM_ARCH_DAVINCI_DA8XX_H */ -- cgit v1.2.1 From 85b8307fd03badbff0da5a75776c62cb45ee6551 Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Sun, 1 Aug 2010 21:17:00 +0400 Subject: DA850: move MII/RMII pin lists to the board file The CPGMAC pin list in da850.c was incorrectly split into two MII/RMII mode specific pin lists, while what pin group is used is a function of how the board is wired. Copy the pin lists to board-da850-evm.c, renaming them accordingly, and merge the two lists in da850.c into one, da850_cpgmac_pins[], representing the CPGMAC module as a whole... Signed-off-by: Sergei Shtylyov Tested-by: Ben Gardiner Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/board-da850-evm.c | 21 +++++++++++++++++++-- arch/arm/mach-davinci/da850.c | 12 +++--------- arch/arm/mach-davinci/include/mach/da8xx.h | 1 - 3 files changed, 22 insertions(+), 12 deletions(-) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c index 482d4584eaa0..190ebd374656 100644 --- a/arch/arm/mach-davinci/board-da850-evm.c +++ b/arch/arm/mach-davinci/board-da850-evm.c @@ -600,6 +600,23 @@ static const short da850_evm_lcdc_pins[] = { -1 }; +static const short da850_evm_mii_pins[] = { + DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3, + DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER, + DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3, + DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK, + DA850_MDIO_D, + -1 +}; + +static const short da850_evm_rmii_pins[] = { + DA850_RMII_TXD_0, DA850_RMII_TXD_1, DA850_RMII_TXEN, + DA850_RMII_CRS_DV, DA850_RMII_RXD_0, DA850_RMII_RXD_1, + DA850_RMII_RXER, DA850_RMII_MHZ_50_CLK, DA850_MDIO_CLK, + DA850_MDIO_D, + -1 +}; + static int __init da850_evm_config_emac(void) { void __iomem *cfg_chip3_base; @@ -617,12 +634,12 @@ static int __init da850_evm_config_emac(void) if (rmii_en) { val |= BIT(8); - ret = davinci_cfg_reg_list(da850_rmii_pins); + ret = davinci_cfg_reg_list(da850_evm_rmii_pins); pr_info("EMAC: RMII PHY configured, MII PHY will not be" " functional\n"); } else { val &= ~BIT(8); - ret = davinci_cfg_reg_list(da850_cpgmac_pins); + ret = davinci_cfg_reg_list(da850_evm_mii_pins); pr_info("EMAC: MII PHY configured, RMII PHY will not be" " functional\n"); } diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c index efb904ebce9c..c2a3ce55b6c5 100644 --- a/arch/arm/mach-davinci/da850.c +++ b/arch/arm/mach-davinci/da850.c @@ -574,15 +574,9 @@ const short da850_cpgmac_pins[] __initdata = { DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER, DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3, DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK, - DA850_MDIO_D, - -1 -}; - -const short da850_rmii_pins[] __initdata = { - DA850_RMII_TXD_0, DA850_RMII_TXD_1, DA850_RMII_TXEN, - DA850_RMII_CRS_DV, DA850_RMII_RXD_0, DA850_RMII_RXD_1, - DA850_RMII_RXER, DA850_RMII_MHZ_50_CLK, DA850_MDIO_CLK, - DA850_MDIO_D, + DA850_MDIO_D, DA850_RMII_TXD_0, DA850_RMII_TXD_1, DA850_RMII_TXEN, + DA850_RMII_CRS_DV, DA850_RMII_RXD_0, DA850_RMII_RXD_1, DA850_RMII_RXER, + DA850_RMII_MHZ_50_CLK, -1 }; diff --git a/arch/arm/mach-davinci/include/mach/da8xx.h b/arch/arm/mach-davinci/include/mach/da8xx.h index 8de2dbbf6fea..504f2f62066c 100644 --- a/arch/arm/mach-davinci/include/mach/da8xx.h +++ b/arch/arm/mach-davinci/include/mach/da8xx.h @@ -121,7 +121,6 @@ extern const short da850_uart2_pins[]; extern const short da850_i2c0_pins[]; extern const short da850_i2c1_pins[]; extern const short da850_cpgmac_pins[]; -extern const short da850_rmii_pins[]; extern const short da850_mcasp_pins[]; extern const short da850_lcdcntl_pins[]; extern const short da850_mmcsd0_pins[]; -- cgit v1.2.1 From 93fe23d8a9d95d8a85dfe2cb37cd9f220bef11b8 Mon Sep 17 00:00:00 2001 From: Kulikov Vasiliy Date: Sat, 17 Jul 2010 19:19:07 +0400 Subject: arm: mach-davinci: check irq2ctlr() result If irq2ctlr() fails return IRQ_NONE. Also as it can fail make 'ctlr' signed. The semantic patch that finds this problem (many false-positive results): (http://coccinelle.lip6.fr/) // @ r1 @ identifier f; @@ int f(...) { ... } @@ identifier r1.f; type T; unsigned T x; @@ *x = f(...) ... *x > 0 Signed-off-by: Kulikov Vasiliy Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/dma.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/dma.c b/arch/arm/mach-davinci/dma.c index 2ede598b77dd..6b9669869c46 100644 --- a/arch/arm/mach-davinci/dma.c +++ b/arch/arm/mach-davinci/dma.c @@ -354,10 +354,12 @@ static int irq2ctlr(int irq) static irqreturn_t dma_irq_handler(int irq, void *data) { int i; - unsigned ctlr; + int ctlr; unsigned int cnt = 0; ctlr = irq2ctlr(irq); + if (ctlr < 0) + return IRQ_NONE; dev_dbg(data, "dma_irq_handler\n"); @@ -408,10 +410,12 @@ static irqreturn_t dma_irq_handler(int irq, void *data) static irqreturn_t dma_ccerr_handler(int irq, void *data) { int i; - unsigned ctlr; + int ctlr; unsigned int cnt = 0; ctlr = irq2ctlr(irq); + if (ctlr < 0) + return IRQ_NONE; dev_dbg(data, "dma_ccerr_handler\n"); -- cgit v1.2.1 From d2b8622c9122841db9c0a09a02d92823d924a1a5 Mon Sep 17 00:00:00 2001 From: Juha Kuikka Date: Thu, 26 Aug 2010 12:40:45 -0700 Subject: DA850: Add LPSC id for MMCSD1 peripheral Add LPSC id for DA850's MMCSD1 peripheral. Signed-off-by: Juha Kuikka Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/include/mach/psc.h | 1 + 1 file changed, 1 insertion(+) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/include/mach/psc.h b/arch/arm/mach-davinci/include/mach/psc.h index 983da6e4554c..62b0858f68ca 100644 --- a/arch/arm/mach-davinci/include/mach/psc.h +++ b/arch/arm/mach-davinci/include/mach/psc.h @@ -172,6 +172,7 @@ #define DA8XX_LPSC1_UART2 13 #define DA8XX_LPSC1_LCDC 16 #define DA8XX_LPSC1_PWM 17 +#define DA850_LPSC1_MMC_SD1 18 #define DA8XX_LPSC1_ECAP 20 #define DA830_LPSC1_EQEP 21 #define DA850_LPSC1_TPTC2 21 -- cgit v1.2.1 From 051a6687336d3310abc85991db7a8917ecc603fc Mon Sep 17 00:00:00 2001 From: Juha Kuikka Date: Thu, 26 Aug 2010 12:40:46 -0700 Subject: DA850: Split MMCSD clock into two to support both MMCSD peripherals Split mmcsd_clk into mmcsd0_clk and mmcsd1_clk and add davinci_mmc.1 in preparation for adding support for MMCSD1 peripheral in DA850. Signed-off-by: Juha Kuikka Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/da850.c | 14 +++++++++++--- 1 file changed, 11 insertions(+), 3 deletions(-) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c index c2a3ce55b6c5..63916b902760 100644 --- a/arch/arm/mach-davinci/da850.c +++ b/arch/arm/mach-davinci/da850.c @@ -325,12 +325,19 @@ static struct clk lcdc_clk = { .gpsc = 1, }; -static struct clk mmcsd_clk = { - .name = "mmcsd", +static struct clk mmcsd0_clk = { + .name = "mmcsd0", .parent = &pll0_sysclk2, .lpsc = DA8XX_LPSC0_MMC_SD, }; +static struct clk mmcsd1_clk = { + .name = "mmcsd1", + .parent = &pll0_sysclk2, + .lpsc = DA850_LPSC1_MMC_SD1, + .gpsc = 1, +}; + static struct clk aemif_clk = { .name = "aemif", .parent = &pll0_sysclk3, @@ -377,7 +384,8 @@ static struct clk_lookup da850_clks[] = { CLK("davinci_emac.1", NULL, &emac_clk), CLK("davinci-mcasp.0", NULL, &mcasp_clk), CLK("da8xx_lcdc.0", NULL, &lcdc_clk), - CLK("davinci_mmc.0", NULL, &mmcsd_clk), + CLK("davinci_mmc.0", NULL, &mmcsd0_clk), + CLK("davinci_mmc.1", NULL, &mmcsd1_clk), CLK(NULL, "aemif", &aemif_clk), CLK(NULL, NULL, NULL), }; -- cgit v1.2.1 From b8241aef7eb54c6e5126b3aa309c2cf0f343c52d Mon Sep 17 00:00:00 2001 From: Juha Kuikka Date: Thu, 26 Aug 2010 12:40:47 -0700 Subject: DA850: Add MMCSD1 resources, platform device and convenience registration function Add resources, platform device and convenience registration function for DA850's second MMC/SD controller (MMCSD1). Signed-off-by: Juha Kuikka Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/devices-da8xx.c | 39 ++++++++++++++++++++++++++++++ arch/arm/mach-davinci/include/mach/da8xx.h | 1 + 2 files changed, 40 insertions(+) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/devices-da8xx.c b/arch/arm/mach-davinci/devices-da8xx.c index 52bc7b1c6ca3..caeb7f4a3a6d 100644 --- a/arch/arm/mach-davinci/devices-da8xx.c +++ b/arch/arm/mach-davinci/devices-da8xx.c @@ -24,6 +24,7 @@ #include "clock.h" #define DA8XX_TPCC_BASE 0x01c00000 +#define DA850_MMCSD1_BASE 0x01e1b000 #define DA850_TPCC1_BASE 0x01e30000 #define DA8XX_TPTC0_BASE 0x01c08000 #define DA8XX_TPTC1_BASE 0x01c08400 @@ -566,6 +567,44 @@ int __init da8xx_register_mmcsd0(struct davinci_mmc_config *config) return platform_device_register(&da8xx_mmcsd0_device); } +#ifdef CONFIG_ARCH_DAVINCI_DA850 +static struct resource da850_mmcsd1_resources[] = { + { /* registers */ + .start = DA850_MMCSD1_BASE, + .end = DA850_MMCSD1_BASE + SZ_4K - 1, + .flags = IORESOURCE_MEM, + }, + { /* interrupt */ + .start = IRQ_DA850_MMCSDINT0_1, + .end = IRQ_DA850_MMCSDINT0_1, + .flags = IORESOURCE_IRQ, + }, + { /* DMA RX */ + .start = EDMA_CTLR_CHAN(1, 28), + .end = EDMA_CTLR_CHAN(1, 28), + .flags = IORESOURCE_DMA, + }, + { /* DMA TX */ + .start = EDMA_CTLR_CHAN(1, 29), + .end = EDMA_CTLR_CHAN(1, 29), + .flags = IORESOURCE_DMA, + }, +}; + +static struct platform_device da850_mmcsd1_device = { + .name = "davinci_mmc", + .id = 1, + .num_resources = ARRAY_SIZE(da850_mmcsd1_resources), + .resource = da850_mmcsd1_resources, +}; + +int __init da850_register_mmcsd1(struct davinci_mmc_config *config) +{ + da850_mmcsd1_device.dev.platform_data = config; + return platform_device_register(&da850_mmcsd1_device); +} +#endif + static struct resource da8xx_rtc_resources[] = { { .start = DA8XX_RTC_BASE, diff --git a/arch/arm/mach-davinci/include/mach/da8xx.h b/arch/arm/mach-davinci/include/mach/da8xx.h index 504f2f62066c..4247b3f53b33 100644 --- a/arch/arm/mach-davinci/include/mach/da8xx.h +++ b/arch/arm/mach-davinci/include/mach/da8xx.h @@ -76,6 +76,7 @@ int da8xx_register_usb11(struct da8xx_ohci_root_hub *pdata); int da8xx_register_emac(void); int da8xx_register_lcdc(struct da8xx_lcdc_platform_data *pdata); int da8xx_register_mmcsd0(struct davinci_mmc_config *config); +int da850_register_mmcsd1(struct davinci_mmc_config *config); void __init da8xx_register_mcasp(int id, struct snd_platform_data *pdata); int da8xx_register_rtc(void); int da850_register_cpufreq(char *async_clk); -- cgit v1.2.1 From 13d36a923da6a1e0584e07d91320373c790c01c3 Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Fri, 27 Aug 2010 14:14:03 +0530 Subject: davinci: dm365 evm: use EDMAQ_3 as the audio DMA queue By default the audio driver uses EDMAQ_0 as the DMA queue, but on DM365 this queue is specially designed for video transfers with a large fifo size. Having both audio and video transfers on the same queue leads to noise on the audio side. This patch changes the audio queue number for DM365 to EDMAQ_3. Signed-off-by: Sekhar Nori Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/board-dm365-evm.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c index 84acef1d0b3d..bdea2da0b203 100644 --- a/arch/arm/mach-davinci/board-dm365-evm.c +++ b/arch/arm/mach-davinci/board-dm365-evm.c @@ -175,7 +175,9 @@ static struct at24_platform_data eeprom_info = { .context = (void *)0x7f00, }; -static struct snd_platform_data dm365_evm_snd_data; +static struct snd_platform_data dm365_evm_snd_data = { + .asp_chan_q = EVENTQ_3, +}; static struct i2c_board_info i2c_info[] = { { -- cgit v1.2.1 From 8060ef4da9e73f461adf2ba1922ea5400a61cf98 Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Mon, 9 Aug 2010 15:46:35 +0530 Subject: davinci: add support for aemif timing configuration This patch adds support to configure the AEMIF interface with supplied timing values. Since this capability is useful both from NOR and NAND flashes, it is provided as a new interface and in a file of its own. AEMIF timing configuration is required in cases: 1) Where the AEMIF clock rate can change at runtime (a side affect of cpu frequency change). 2) Where U-Boot does not support NAND/NOR but supports other media like SPI Flash or MMC/SD and thus does not care about setting up the AEMIF timing for kernel to use. 3) Where U-Boot just hasn't configured the timing values and cannot be upgraded because the box is already in the field. Since there is now a header file for AEMIF interface, the common (non-NAND specific) defines for AEMIF registers have been moved from nand.h into the newly created aemif.h Signed-off-by: Sekhar Nori Acked-by: Kevin Hilman Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/Makefile | 2 +- arch/arm/mach-davinci/aemif.c | 133 +++++++++++++++++++++++++++++ arch/arm/mach-davinci/include/mach/aemif.h | 36 ++++++++ arch/arm/mach-davinci/include/mach/nand.h | 3 - 4 files changed, 170 insertions(+), 4 deletions(-) create mode 100644 arch/arm/mach-davinci/aemif.c create mode 100644 arch/arm/mach-davinci/include/mach/aemif.h (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/Makefile b/arch/arm/mach-davinci/Makefile index eab4c0fd667a..77a0f71b2aa2 100644 --- a/arch/arm/mach-davinci/Makefile +++ b/arch/arm/mach-davinci/Makefile @@ -5,7 +5,7 @@ # Common objects obj-y := time.o clock.o serial.o io.o psc.o \ - gpio.o dma.o usb.o common.o sram.o + gpio.o dma.o usb.o common.o sram.o aemif.o obj-$(CONFIG_DAVINCI_MUX) += mux.o diff --git a/arch/arm/mach-davinci/aemif.c b/arch/arm/mach-davinci/aemif.c new file mode 100644 index 000000000000..9c3f500fc12f --- /dev/null +++ b/arch/arm/mach-davinci/aemif.c @@ -0,0 +1,133 @@ +/* + * AEMIF support for DaVinci SoCs + * + * Copyright (C) 2010 Texas Instruments Incorporated. http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include +#include + +#include + +/* Timing value configuration */ + +#define TA(x) ((x) << 2) +#define RHOLD(x) ((x) << 4) +#define RSTROBE(x) ((x) << 7) +#define RSETUP(x) ((x) << 13) +#define WHOLD(x) ((x) << 17) +#define WSTROBE(x) ((x) << 20) +#define WSETUP(x) ((x) << 26) + +#define TA_MAX 0x3 +#define RHOLD_MAX 0x7 +#define RSTROBE_MAX 0x3f +#define RSETUP_MAX 0xf +#define WHOLD_MAX 0x7 +#define WSTROBE_MAX 0x3f +#define WSETUP_MAX 0xf + +#define TIMING_MASK (TA(TA_MAX) | \ + RHOLD(RHOLD_MAX) | \ + RSTROBE(RSTROBE_MAX) | \ + RSETUP(RSETUP_MAX) | \ + WHOLD(WHOLD_MAX) | \ + WSTROBE(WSTROBE_MAX) | \ + WSETUP(WSETUP_MAX)) + +/* + * aemif_calc_rate - calculate timing data. + * @wanted: The cycle time needed in nanoseconds. + * @clk: The input clock rate in kHz. + * @max: The maximum divider value that can be programmed. + * + * On success, returns the calculated timing value minus 1 for easy + * programming into AEMIF timing registers, else negative errno. + */ +static int aemif_calc_rate(int wanted, unsigned long clk, int max) +{ + int result; + + result = DIV_ROUND_UP((wanted * clk), NSEC_PER_MSEC) - 1; + + pr_debug("%s: result %d from %ld, %d\n", __func__, result, clk, wanted); + + /* It is generally OK to have a more relaxed timing than requested... */ + if (result < 0) + result = 0; + + /* ... But configuring tighter timings is not an option. */ + else if (result > max) + result = -EINVAL; + + return result; +} + +/** + * davinci_aemif_setup_timing - setup timing values for a given AEMIF interface + * @t: timing values to be progammed + * @base: The virtual base address of the AEMIF interface + * @cs: chip-select to program the timing values for + * + * This function programs the given timing values (in real clock) into the + * AEMIF registers taking the AEMIF clock into account. + * + * This function does not use any locking while programming the AEMIF + * because it is expected that there is only one user of a given + * chip-select. + * + * Returns 0 on success, else negative errno. + */ +int davinci_aemif_setup_timing(struct davinci_aemif_timing *t, + void __iomem *base, unsigned cs) +{ + unsigned set, val; + unsigned ta, rhold, rstrobe, rsetup, whold, wstrobe, wsetup; + unsigned offset = A1CR_OFFSET + cs * 4; + struct clk *aemif_clk; + unsigned long clkrate; + + if (!t) + return 0; /* Nothing to do */ + + aemif_clk = clk_get(NULL, "aemif"); + if (IS_ERR(aemif_clk)) + return PTR_ERR(aemif_clk); + + clkrate = clk_get_rate(aemif_clk); + + clkrate /= 1000; /* turn clock into kHz for ease of use */ + + ta = aemif_calc_rate(t->ta, clkrate, TA_MAX); + rhold = aemif_calc_rate(t->rhold, clkrate, RHOLD_MAX); + rstrobe = aemif_calc_rate(t->rstrobe, clkrate, RSTROBE_MAX); + rsetup = aemif_calc_rate(t->rsetup, clkrate, RSETUP_MAX); + whold = aemif_calc_rate(t->whold, clkrate, WHOLD_MAX); + wstrobe = aemif_calc_rate(t->wstrobe, clkrate, WSTROBE_MAX); + wsetup = aemif_calc_rate(t->wsetup, clkrate, WSETUP_MAX); + + if (ta < 0 || rhold < 0 || rstrobe < 0 || rsetup < 0 || + whold < 0 || wstrobe < 0 || wsetup < 0) { + pr_err("%s: cannot get suitable timings\n", __func__); + return -EINVAL; + } + + set = TA(ta) | RHOLD(rhold) | RSTROBE(rstrobe) | RSETUP(rsetup) | + WHOLD(whold) | WSTROBE(wstrobe) | WSETUP(wsetup); + + val = __raw_readl(base + offset); + val &= ~TIMING_MASK; + val |= set; + __raw_writel(val, base + offset); + + return 0; +} +EXPORT_SYMBOL(davinci_aemif_setup_timing); diff --git a/arch/arm/mach-davinci/include/mach/aemif.h b/arch/arm/mach-davinci/include/mach/aemif.h new file mode 100644 index 000000000000..05b293443097 --- /dev/null +++ b/arch/arm/mach-davinci/include/mach/aemif.h @@ -0,0 +1,36 @@ +/* + * TI DaVinci AEMIF support + * + * Copyright 2010 (C) Texas Instruments, Inc. http://www.ti.com/ + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ +#ifndef _MACH_DAVINCI_AEMIF_H +#define _MACH_DAVINCI_AEMIF_H + +#define NRCSR_OFFSET 0x00 +#define AWCCR_OFFSET 0x04 +#define A1CR_OFFSET 0x10 + +#define ACR_ASIZE_MASK 0x3 +#define ACR_EW_MASK BIT(30) +#define ACR_SS_MASK BIT(31) + +/* All timings in nanoseconds */ +struct davinci_aemif_timing { + u8 wsetup; + u8 wstrobe; + u8 whold; + + u8 rsetup; + u8 rstrobe; + u8 rhold; + + u8 ta; +}; + +int davinci_aemif_setup_timing(struct davinci_aemif_timing *t, + void __iomem *base, unsigned cs); +#endif diff --git a/arch/arm/mach-davinci/include/mach/nand.h b/arch/arm/mach-davinci/include/mach/nand.h index b2ad8090bd10..b5893f035fea 100644 --- a/arch/arm/mach-davinci/include/mach/nand.h +++ b/arch/arm/mach-davinci/include/mach/nand.h @@ -30,9 +30,6 @@ #include -#define NRCSR_OFFSET 0x00 -#define AWCCR_OFFSET 0x04 -#define A1CR_OFFSET 0x10 #define NANDFCR_OFFSET 0x60 #define NANDFSR_OFFSET 0x64 #define NANDF1ECC_OFFSET 0x70 -- cgit v1.2.1 From a88dbc5bfdd26132bbf0ad19dd672e036971d74d Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Mon, 9 Aug 2010 15:46:36 +0530 Subject: nand: davinci: add support for timing configuration This patch modifies the DaVinci NAND driver to use the new AEMIF timing setup API to configure the NAND access timings. Earlier, AEMIF configuration was being done as a special case for DM644x board, but now more boards emerge which have capability to boot for other media (SPI flash, NOR flash) and have the kernel access NAND flash. This means that kernel cannot always depend on the bootloader to setup the NAND. Also, on platforms such as da850/omap-l138, the aemif input frequency changes as cpu frequency changes; necessiating re-calculation of timimg values as part of cpufreq transtitions. This patch forms the basis for adding that support. Signed-off-by: Sekhar Nori Acked-by: Kevin Hilman Signed-off-by: Artem Bityutskiy --- arch/arm/mach-davinci/include/mach/nand.h | 3 +++ 1 file changed, 3 insertions(+) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/include/mach/nand.h b/arch/arm/mach-davinci/include/mach/nand.h index b5893f035fea..025151049f05 100644 --- a/arch/arm/mach-davinci/include/mach/nand.h +++ b/arch/arm/mach-davinci/include/mach/nand.h @@ -80,6 +80,9 @@ struct davinci_nand_pdata { /* platform_data */ /* Main and mirror bbt descriptor overrides */ struct nand_bbt_descr *bbt_td; struct nand_bbt_descr *bbt_md; + + /* Access timings */ + struct davinci_aemif_timing *timing; }; #endif /* __ARCH_ARM_DAVINCI_NAND_H */ -- cgit v1.2.1 From fe69c82d0862f54b1a5aa5ece046468b4e76b40c Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Mon, 9 Aug 2010 15:46:37 +0530 Subject: davinci: dm644x evm: setup NAND flash timing The DM644x EVM nand flash timing was earlier being done as a special case in the NAND driver itself. With the NAND driver now capable of progamming the AEMIF interface using timing data passed from the platform, the timing values are being moved into their rightful place in the EVM specific board file. The values being programmed match what was being done earlier and thus do not represent any change in performance/functionality. Signed-off-by: Sekhar Nori Acked-by: Kevin Hilman Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/board-dm644x-evm.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/board-dm644x-evm.c b/arch/arm/mach-davinci/board-dm644x-evm.c index 34c8b418cd72..65bb94064feb 100644 --- a/arch/arm/mach-davinci/board-dm644x-evm.c +++ b/arch/arm/mach-davinci/board-dm644x-evm.c @@ -37,6 +37,7 @@ #include #include #include +#include #define DM644X_EVM_PHY_MASK (0x2) #define DM644X_EVM_MDIO_FREQUENCY (2200000) /* PHY bus frequency */ @@ -137,11 +138,22 @@ static struct mtd_partition davinci_evm_nandflash_partition[] = { */ }; +static struct davinci_aemif_timing davinci_evm_nandflash_timing = { + .wsetup = 20, + .wstrobe = 40, + .whold = 20, + .rsetup = 10, + .rstrobe = 40, + .rhold = 10, + .ta = 40, +}; + static struct davinci_nand_pdata davinci_evm_nandflash_data = { .parts = davinci_evm_nandflash_partition, .nr_parts = ARRAY_SIZE(davinci_evm_nandflash_partition), .ecc_mode = NAND_ECC_HW, .options = NAND_USE_FLASH_BBT, + .timing = &davinci_evm_nandflash_timing, }; static struct resource davinci_evm_nandflash_resource[] = { -- cgit v1.2.1 From 217f13662f291d8eaac5a3dfd7ba35be0a91c9fc Mon Sep 17 00:00:00 2001 From: Sudhakar Rajashekhara Date: Mon, 9 Aug 2010 15:46:38 +0530 Subject: davinci: am17x/da830/omap-l137 evm: setup NAND flash timing Setup the NAND flash timings for DA830 EVM. Before configuring the timing values, throughput calculation using dd command yielded 477 kB/s write and 970 kB/s read speed. After the timing configuration, the throughput was measured to be 2.5 MB/s write and 5.1 MB/s read. [Mukul Bhatnagar: actual calculation of timing values from the NAND datasheet] Signed-off-by: Sudhakar Rajashekhara Cc: Mukul Bhatnagar Signed-off-by: Sekhar Nori Acked-by: Kevin Hilman Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/board-da830-evm.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/board-da830-evm.c b/arch/arm/mach-davinci/board-da830-evm.c index 292e8b7c02ac..de82739c00ec 100644 --- a/arch/arm/mach-davinci/board-da830-evm.c +++ b/arch/arm/mach-davinci/board-da830-evm.c @@ -29,6 +29,7 @@ #include #include #include +#include #define DA830_EVM_PHY_MASK 0x0 #define DA830_EVM_MDIO_FREQUENCY 2200000 /* PHY bus frequency */ @@ -360,6 +361,16 @@ static struct nand_bbt_descr da830_evm_nand_bbt_mirror_descr = { .pattern = da830_evm_nand_mirror_pattern }; +static struct davinci_aemif_timing da830_evm_nandflash_timing = { + .wsetup = 24, + .wstrobe = 21, + .whold = 14, + .rsetup = 19, + .rstrobe = 50, + .rhold = 0, + .ta = 20, +}; + static struct davinci_nand_pdata da830_evm_nand_pdata = { .parts = da830_evm_nand_partitions, .nr_parts = ARRAY_SIZE(da830_evm_nand_partitions), @@ -368,6 +379,7 @@ static struct davinci_nand_pdata da830_evm_nand_pdata = { .options = NAND_USE_FLASH_BBT, .bbt_td = &da830_evm_nand_bbt_main_descr, .bbt_md = &da830_evm_nand_bbt_mirror_descr, + .timing = &da830_evm_nandflash_timing, }; static struct resource da830_evm_nand_resources[] = { -- cgit v1.2.1 From 18a8505cc130448c8c0a29a46573b46697bf0e42 Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Mon, 9 Aug 2010 15:46:39 +0530 Subject: davinci: am18x/da850/omap-l138 evm: setup NAND flash timing Setup the NAND flash timings for DA850 EVM Before configuring the timing values, throughput calculation using dd command yielded 469 kB/s write and 966 kB/s read speed. After the timing configuration, the throughput was measured to be 2.4 MB/s write and 5 MB/s read. [Mukul Bhatnagar: actual calculation of timing values from the NAND datasheet] Signed-off-by: Sekhar Nori Cc: Mukul Bhatnagar Acked-by: Kevin Hilman Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/board-da850-evm.c | 12 ++++++++++++ 1 file changed, 12 insertions(+) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c index 190ebd374656..c1d45d7ac45b 100644 --- a/arch/arm/mach-davinci/board-da850-evm.c +++ b/arch/arm/mach-davinci/board-da850-evm.c @@ -36,6 +36,7 @@ #include #include #include +#include #define DA850_EVM_PHY_MASK 0x1 #define DA850_EVM_MDIO_FREQUENCY 2200000 /* PHY bus frequency */ @@ -143,12 +144,23 @@ static struct mtd_partition da850_evm_nandflash_partition[] = { }, }; +static struct davinci_aemif_timing da850_evm_nandflash_timing = { + .wsetup = 24, + .wstrobe = 21, + .whold = 14, + .rsetup = 19, + .rstrobe = 50, + .rhold = 0, + .ta = 20, +}; + static struct davinci_nand_pdata da850_evm_nandflash_data = { .parts = da850_evm_nandflash_partition, .nr_parts = ARRAY_SIZE(da850_evm_nandflash_partition), .ecc_mode = NAND_ECC_HW, .ecc_bits = 4, .options = NAND_USE_FLASH_BBT, + .timing = &da850_evm_nandflash_timing, }; static struct resource da850_evm_nandflash_resource[] = { -- cgit v1.2.1 From 0b3fc7bb88243371a2bd4a4990fb62a0b722efe7 Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Mon, 9 Aug 2010 15:46:40 +0530 Subject: davinci: dm6467t evm: setup NAND flash timing Setup NAND flash timing on DM6467T EVM. Without the timing setup, the NAND flash on DM6467T RevC EVM reports a number of random bad blocks because of read errors. Also, with this, copying a 100M file on RevB EVM takes ~35 sec against 1 minute 30 seconds earlier. Signed-off-by: Sekhar Nori Acked-by: Kevin Hilman Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/board-dm646x-evm.c | 14 ++++++++++++++ 1 file changed, 14 insertions(+) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/board-dm646x-evm.c b/arch/arm/mach-davinci/board-dm646x-evm.c index 4502f346b2b0..5a29955b2f5c 100644 --- a/arch/arm/mach-davinci/board-dm646x-evm.c +++ b/arch/arm/mach-davinci/board-dm646x-evm.c @@ -42,6 +42,7 @@ #include #include #include +#include #include "clock.h" @@ -71,6 +72,16 @@ static struct mtd_partition davinci_nand_partitions[] = { } }; +static struct davinci_aemif_timing dm6467tevm_nandflash_timing = { + .wsetup = 29, + .wstrobe = 24, + .whold = 14, + .rsetup = 19, + .rstrobe = 33, + .rhold = 0, + .ta = 29, +}; + static struct davinci_nand_pdata davinci_nand_data = { .mask_cle = 0x80000, .mask_ale = 0x40000, @@ -763,6 +774,9 @@ static __init void evm_init(void) dm646x_init_mcasp0(&dm646x_evm_snd_data[0]); dm646x_init_mcasp1(&dm646x_evm_snd_data[1]); + if (machine_is_davinci_dm6467tevm()) + davinci_nand_data.timing = &dm6467tevm_nandflash_timing; + platform_device_register(&davinci_nand_device); dm646x_init_edma(dm646x_edma_rsv); -- cgit v1.2.1 From 1aa5f2a9c1575279baf06e94a4bd3b3b86b7f176 Mon Sep 17 00:00:00 2001 From: Michael Williamson Date: Tue, 31 Aug 2010 14:30:15 -0400 Subject: davinci: Add machine checks to DA8XX serial console init routines This patch adds machine checks in the serial console init routines for the DA8XX EVM boards. This is needed because there are other DA8XX based machines that use a different UART/tty as the console and may be included in a common kernel build. Signed-off-by: Michael Williamson Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/board-da830-evm.c | 3 +++ arch/arm/mach-davinci/board-da850-evm.c | 3 +++ 2 files changed, 6 insertions(+) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/board-da830-evm.c b/arch/arm/mach-davinci/board-da830-evm.c index de82739c00ec..ef1ab0b6576e 100644 --- a/arch/arm/mach-davinci/board-da830-evm.c +++ b/arch/arm/mach-davinci/board-da830-evm.c @@ -598,6 +598,9 @@ static __init void da830_evm_init(void) #ifdef CONFIG_SERIAL_8250_CONSOLE static int __init da830_evm_console_init(void) { + if (!machine_is_davinci_da830_evm()) + return 0; + return add_preferred_console("ttyS", 2, "115200"); } console_initcall(da830_evm_console_init); diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c index c1d45d7ac45b..ac2297c69a92 100644 --- a/arch/arm/mach-davinci/board-da850-evm.c +++ b/arch/arm/mach-davinci/board-da850-evm.c @@ -859,6 +859,9 @@ static __init void da850_evm_init(void) #ifdef CONFIG_SERIAL_8250_CONSOLE static int __init da850_evm_console_init(void) { + if (!machine_is_davinci_da850_evm()) + return 0; + return add_preferred_console("ttyS", 2, "115200"); } console_initcall(da850_evm_console_init); -- cgit v1.2.1 From f2dbb6d91b53d3ffbc85152aa7265599f0a4d850 Mon Sep 17 00:00:00 2001 From: Michael Williamson Date: Thu, 2 Sep 2010 13:58:07 -0400 Subject: davinci: Initial support for MityDSP-L138/MityARM-1808 This patch adds initial support for the MityDSP-L138 and MityDSP-1808 system on Module (SOM) under the machine name "mityomapl138". These SOMs are based on the da850 davinci CPU architecture. Information on these SOMs may be found at http://www.mitydsp.com. Basic support for the console UART, NAND, and EMAC (MII interface) is included in this patch. Signed-off-by: Michael Williamson Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/Kconfig | 8 + arch/arm/mach-davinci/Makefile | 1 + arch/arm/mach-davinci/board-mityomapl138.c | 221 ++++++++++++++++++++++++ arch/arm/mach-davinci/include/mach/uncompress.h | 1 + 4 files changed, 231 insertions(+) create mode 100644 arch/arm/mach-davinci/board-mityomapl138.c (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig index 2bf03e95505f..9aca60cb4241 100644 --- a/arch/arm/mach-davinci/Kconfig +++ b/arch/arm/mach-davinci/Kconfig @@ -185,6 +185,14 @@ config MACH_TNETV107X help Say Y here to select the TI TNETV107X Evaluation Module. +config MACH_MITYOMAPL138 + bool "Critical Link MityDSP-L138/MityARM-1808 SoM" + depends on ARCH_DAVINCI_DA850 + help + Say Y here to select the Critical Link MityDSP-L138/MityARM-1808 + System on Module. Information on this SoM may be found at + http://www.mitydsp.com + config DAVINCI_MUX bool "DAVINCI multiplexing support" depends on ARCH_DAVINCI diff --git a/arch/arm/mach-davinci/Makefile b/arch/arm/mach-davinci/Makefile index 77a0f71b2aa2..a7a70d1ba363 100644 --- a/arch/arm/mach-davinci/Makefile +++ b/arch/arm/mach-davinci/Makefile @@ -33,6 +33,7 @@ obj-$(CONFIG_MACH_DAVINCI_DM365_EVM) += board-dm365-evm.o obj-$(CONFIG_MACH_DAVINCI_DA830_EVM) += board-da830-evm.o obj-$(CONFIG_MACH_DAVINCI_DA850_EVM) += board-da850-evm.o obj-$(CONFIG_MACH_TNETV107X) += board-tnetv107x-evm.o +obj-$(CONFIG_MACH_MITYOMAPL138) += board-mityomapl138.o # Power Management obj-$(CONFIG_CPU_FREQ) += cpufreq.o diff --git a/arch/arm/mach-davinci/board-mityomapl138.c b/arch/arm/mach-davinci/board-mityomapl138.c new file mode 100644 index 000000000000..7146916fa498 --- /dev/null +++ b/arch/arm/mach-davinci/board-mityomapl138.c @@ -0,0 +1,221 @@ +/* + * Critical Link MityOMAP-L138 SoM + * + * Copyright (C) 2010 Critical Link LLC - http://www.criticallink.com + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of + * any kind, whether express or implied. + */ + +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include +#include +#include + +#define MITYOMAPL138_PHY_MASK 0x08 /* hardcoded for now */ +#define MITYOMAPL138_MDIO_FREQUENCY (2200000) /* PHY bus frequency */ + +/* + * MityDSP-L138 includes a 256 MByte large-page NAND flash + * (128K blocks). + */ +struct mtd_partition mityomapl138_nandflash_partition[] = { + { + .name = "rootfs", + .offset = 0, + .size = SZ_128M, + .mask_flags = 0, /* MTD_WRITEABLE, */ + }, + { + .name = "homefs", + .offset = MTDPART_OFS_APPEND, + .size = MTDPART_SIZ_FULL, + .mask_flags = 0, + }, +}; + +static struct davinci_nand_pdata mityomapl138_nandflash_data = { + .parts = mityomapl138_nandflash_partition, + .nr_parts = ARRAY_SIZE(mityomapl138_nandflash_partition), + .ecc_mode = NAND_ECC_HW, + .options = NAND_USE_FLASH_BBT | NAND_BUSWIDTH_16, + .ecc_bits = 1, /* 4 bit mode is not supported with 16 bit NAND */ +}; + +static struct resource mityomapl138_nandflash_resource[] = { + { + .start = DA8XX_AEMIF_CS3_BASE, + .end = DA8XX_AEMIF_CS3_BASE + SZ_512K + 2 * SZ_1K - 1, + .flags = IORESOURCE_MEM, + }, + { + .start = DA8XX_AEMIF_CTL_BASE, + .end = DA8XX_AEMIF_CTL_BASE + SZ_32K - 1, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device mityomapl138_nandflash_device = { + .name = "davinci_nand", + .id = 0, + .dev = { + .platform_data = &mityomapl138_nandflash_data, + }, + .num_resources = ARRAY_SIZE(mityomapl138_nandflash_resource), + .resource = mityomapl138_nandflash_resource, +}; + +static struct platform_device *mityomapl138_devices[] __initdata = { + &mityomapl138_nandflash_device, +}; + +static void __init mityomapl138_setup_nand(void) +{ + platform_add_devices(mityomapl138_devices, + ARRAY_SIZE(mityomapl138_devices)); +} + +static struct davinci_uart_config mityomapl138_uart_config __initdata = { + .enabled_uarts = 0x7, +}; + +static const short mityomap_mii_pins[] = { + DA850_MII_TXEN, DA850_MII_TXCLK, DA850_MII_COL, DA850_MII_TXD_3, + DA850_MII_TXD_2, DA850_MII_TXD_1, DA850_MII_TXD_0, DA850_MII_RXER, + DA850_MII_CRS, DA850_MII_RXCLK, DA850_MII_RXDV, DA850_MII_RXD_3, + DA850_MII_RXD_2, DA850_MII_RXD_1, DA850_MII_RXD_0, DA850_MDIO_CLK, + DA850_MDIO_D, + -1 +}; + +static const short mityomap_rmii_pins[] = { + DA850_RMII_TXD_0, DA850_RMII_TXD_1, DA850_RMII_TXEN, + DA850_RMII_CRS_DV, DA850_RMII_RXD_0, DA850_RMII_RXD_1, + DA850_RMII_RXER, DA850_RMII_MHZ_50_CLK, DA850_MDIO_CLK, + DA850_MDIO_D, + -1 +}; + +static void __init mityomapl138_config_emac(void) +{ + void __iomem *cfg_chip3_base; + int ret; + u32 val; + struct davinci_soc_info *soc_info = &davinci_soc_info; + + soc_info->emac_pdata->rmii_en = 0; /* hardcoded for now */ + + cfg_chip3_base = DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP3_REG); + val = __raw_readl(cfg_chip3_base); + + if (soc_info->emac_pdata->rmii_en) { + val |= BIT(8); + ret = davinci_cfg_reg_list(mityomap_rmii_pins); + pr_info("RMII PHY configured\n"); + } else { + val &= ~BIT(8); + ret = davinci_cfg_reg_list(mityomap_mii_pins); + pr_info("MII PHY configured\n"); + } + + if (ret) { + pr_warning("mii/rmii mux setup failed: %d\n", ret); + return; + } + + /* configure the CFGCHIP3 register for RMII or MII */ + __raw_writel(val, cfg_chip3_base); + + soc_info->emac_pdata->phy_mask = MITYOMAPL138_PHY_MASK; + pr_debug("setting phy_mask to %x\n", soc_info->emac_pdata->phy_mask); + soc_info->emac_pdata->mdio_max_freq = MITYOMAPL138_MDIO_FREQUENCY; + + ret = da8xx_register_emac(); + if (ret) + pr_warning("emac registration failed: %d\n", ret); +} + +static struct davinci_pm_config da850_pm_pdata = { + .sleepcount = 128, +}; + +static struct platform_device da850_pm_device = { + .name = "pm-davinci", + .dev = { + .platform_data = &da850_pm_pdata, + }, + .id = -1, +}; + +static void __init mityomapl138_init(void) +{ + int ret; + + /* for now, no special EDMA channels are reserved */ + ret = da850_register_edma(NULL); + if (ret) + pr_warning("edma registration failed: %d\n", ret); + + ret = da8xx_register_watchdog(); + if (ret) + pr_warning("watchdog registration failed: %d\n", ret); + + davinci_serial_init(&mityomapl138_uart_config); + + mityomapl138_setup_nand(); + + mityomapl138_config_emac(); + + ret = da8xx_register_rtc(); + if (ret) + pr_warning("rtc setup failed: %d\n", ret); + + ret = da850_register_cpufreq("pll0_sysclk3"); + if (ret) + pr_warning("cpufreq registration failed: %d\n", ret); + + ret = da8xx_register_cpuidle(); + if (ret) + pr_warning("cpuidle registration failed: %d\n", ret); + + ret = da850_register_pm(&da850_pm_device); + if (ret) + pr_warning("da850_evm_init: suspend registration failed: %d\n", + ret); +} + +#ifdef CONFIG_SERIAL_8250_CONSOLE +static int __init mityomapl138_console_init(void) +{ + if (!machine_is_mityomapl138()) + return 0; + + return add_preferred_console("ttyS", 1, "115200"); +} +console_initcall(mityomapl138_console_init); +#endif + +static void __init mityomapl138_map_io(void) +{ + da850_init(); +} + +MACHINE_START(MITYOMAPL138, "MityDSP-L138/MityARM-1808") + .phys_io = IO_PHYS, + .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc, + .boot_params = (DA8XX_DDR_BASE + 0x100), + .map_io = mityomapl138_map_io, + .init_irq = cp_intc_init, + .timer = &davinci_timer, + .init_machine = mityomapl138_init, +MACHINE_END diff --git a/arch/arm/mach-davinci/include/mach/uncompress.h b/arch/arm/mach-davinci/include/mach/uncompress.h index 15a6192ad6eb..d370391d6f31 100644 --- a/arch/arm/mach-davinci/include/mach/uncompress.h +++ b/arch/arm/mach-davinci/include/mach/uncompress.h @@ -88,6 +88,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id) /* DA8xx boards */ DEBUG_LL_DA8XX(davinci_da830_evm, 2); DEBUG_LL_DA8XX(davinci_da850_evm, 2); + DEBUG_LL_DA8XX(mityomapl138, 1); /* TNETV107x boards */ DEBUG_LL_TNETV107X(tnetv107x, 1); -- cgit v1.2.1 From b41547c153436712daef544c0f18547fcb70f4ac Mon Sep 17 00:00:00 2001 From: Cyril Chemparathy Date: Fri, 3 Sep 2010 16:01:59 -0400 Subject: davinci: add idcode for tnetv107x rev 1.1/1.2 This patch adds an entry into the idcode table for tnetv107x silicon revision 1.1 and 1.2 devices. Signed-off-by: Cyril Chemparathy Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/tnetv107x.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/tnetv107x.c b/arch/arm/mach-davinci/tnetv107x.c index 06d2ac9dcf3d..daeae06430b9 100644 --- a/arch/arm/mach-davinci/tnetv107x.c +++ b/arch/arm/mach-davinci/tnetv107x.c @@ -581,7 +581,14 @@ static struct davinci_id ids[] = { .part_no = 0xb8a1, .manufacturer = 0x017, .cpu_id = DAVINCI_CPU_ID_TNETV107X, - .name = "tnetv107x rev1.0", + .name = "tnetv107x rev 1.0", + }, + { + .variant = 0x1, + .part_no = 0xb8a1, + .manufacturer = 0x017, + .cpu_id = DAVINCI_CPU_ID_TNETV107X, + .name = "tnetv107x rev 1.1/1.2", }, }; -- cgit v1.2.1 From 8774882394190fe52d1df449b1e1c6cff9c3088c Mon Sep 17 00:00:00 2001 From: Michael Williamson Date: Sun, 5 Sep 2010 13:29:39 -0400 Subject: davinci: Add I2C0 devices to MityDSP-L138/MityARM-1808 platform This patch adds the i2c0 bus and attached devices to the MityDSP-L138 and MityARM-1808 davinci SoM. Included is a TPS65023 voltage regulator needed for power management and a small 24c02 EPROM that contains factory configuration data. Signed-off-by: Michael Williamson Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/board-mityomapl138.c | 145 +++++++++++++++++++++++++++++ 1 file changed, 145 insertions(+) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/board-mityomapl138.c b/arch/arm/mach-davinci/board-mityomapl138.c index 7146916fa498..84d5aff50de4 100644 --- a/arch/arm/mach-davinci/board-mityomapl138.c +++ b/arch/arm/mach-davinci/board-mityomapl138.c @@ -13,6 +13,8 @@ #include #include #include +#include +#include #include #include @@ -25,6 +27,141 @@ #define MITYOMAPL138_PHY_MASK 0x08 /* hardcoded for now */ #define MITYOMAPL138_MDIO_FREQUENCY (2200000) /* PHY bus frequency */ +static struct davinci_i2c_platform_data mityomap_i2c_0_pdata = { + .bus_freq = 100, /* kHz */ + .bus_delay = 0, /* usec */ +}; + +/* TPS65023 voltage regulator support */ +/* 1.2V Core */ +struct regulator_consumer_supply tps65023_dcdc1_consumers[] = { + { + .supply = "cvdd", + }, +}; + +/* 1.8V */ +struct regulator_consumer_supply tps65023_dcdc2_consumers[] = { + { + .supply = "usb0_vdda18", + }, + { + .supply = "usb1_vdda18", + }, + { + .supply = "ddr_dvdd18", + }, + { + .supply = "sata_vddr", + }, +}; + +/* 1.2V */ +struct regulator_consumer_supply tps65023_dcdc3_consumers[] = { + { + .supply = "sata_vdd", + }, + { + .supply = "usb_cvdd", + }, + { + .supply = "pll0_vdda", + }, + { + .supply = "pll1_vdda", + }, +}; + +/* 1.8V Aux LDO, not used */ +struct regulator_consumer_supply tps65023_ldo1_consumers[] = { + { + .supply = "1.8v_aux", + }, +}; + +/* FPGA VCC Aux (2.5 or 3.3) LDO */ +struct regulator_consumer_supply tps65023_ldo2_consumers[] = { + { + .supply = "vccaux", + }, +}; + +struct regulator_init_data tps65023_regulator_data[] = { + /* dcdc1 */ + { + .constraints = { + .min_uV = 1150000, + .max_uV = 1350000, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS, + .boot_on = 1, + }, + .num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc1_consumers), + .consumer_supplies = tps65023_dcdc1_consumers, + }, + /* dcdc2 */ + { + .constraints = { + .min_uV = 1800000, + .max_uV = 1800000, + .valid_ops_mask = REGULATOR_CHANGE_STATUS, + .boot_on = 1, + }, + .num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc2_consumers), + .consumer_supplies = tps65023_dcdc2_consumers, + }, + /* dcdc3 */ + { + .constraints = { + .min_uV = 1200000, + .max_uV = 1200000, + .valid_ops_mask = REGULATOR_CHANGE_STATUS, + .boot_on = 1, + }, + .num_consumer_supplies = ARRAY_SIZE(tps65023_dcdc3_consumers), + .consumer_supplies = tps65023_dcdc3_consumers, + }, + /* ldo1 */ + { + .constraints = { + .min_uV = 1800000, + .max_uV = 1800000, + .valid_ops_mask = REGULATOR_CHANGE_STATUS, + .boot_on = 1, + }, + .num_consumer_supplies = ARRAY_SIZE(tps65023_ldo1_consumers), + .consumer_supplies = tps65023_ldo1_consumers, + }, + /* ldo2 */ + { + .constraints = { + .min_uV = 2500000, + .max_uV = 3300000, + .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE | + REGULATOR_CHANGE_STATUS, + .boot_on = 1, + }, + .num_consumer_supplies = ARRAY_SIZE(tps65023_ldo2_consumers), + .consumer_supplies = tps65023_ldo2_consumers, + }, +}; + +static struct i2c_board_info __initdata mityomap_tps65023_info[] = { + { + I2C_BOARD_INFO("tps65023", 0x48), + .platform_data = &tps65023_regulator_data[0], + }, + { + I2C_BOARD_INFO("24c02", 0x50), + }, +}; + +static int __init pmic_tps65023_init(void) +{ + return i2c_register_board_info(1, mityomap_tps65023_info, + ARRAY_SIZE(mityomap_tps65023_info)); +} + /* * MityDSP-L138 includes a 256 MByte large-page NAND flash * (128K blocks). @@ -172,6 +309,14 @@ static void __init mityomapl138_init(void) davinci_serial_init(&mityomapl138_uart_config); + ret = da8xx_register_i2c(0, &mityomap_i2c_0_pdata); + if (ret) + pr_warning("i2c0 registration failed: %d\n", ret); + + ret = pmic_tps65023_init(); + if (ret) + pr_warning("TPS65023 PMIC init failed: %d\n", ret); + mityomapl138_setup_nand(); mityomapl138_config_emac(); -- cgit v1.2.1 From d22960c8bbb8f685c2d8c4051e1f335ab13dca24 Mon Sep 17 00:00:00 2001 From: Cyril Chemparathy Date: Wed, 15 Sep 2010 10:11:22 -0400 Subject: davinci: add mdio platform devices This patch adds mdio platform devices on SoCs that have the necessary hardware. Clock lookup entries (aliases) have also been added, so that the MDIO and EMAC drivers can independently enable/disable a shared underlying clock. Further, the EMAC MMR region has been split down into separate MDIO and EMAC regions. Signed-off-by: Cyril Chemparathy Acked-by: David S. Miller Tested-by: Michael Williamson Tested-by: Caglar Akyuz Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/devices-da8xx.c | 29 +++++++++++++++++++++++++++-- arch/arm/mach-davinci/dm365.c | 22 +++++++++++++++++++++- arch/arm/mach-davinci/dm644x.c | 22 +++++++++++++++++++++- arch/arm/mach-davinci/dm646x.c | 21 ++++++++++++++++++++- arch/arm/mach-davinci/include/mach/dm365.h | 1 + arch/arm/mach-davinci/include/mach/dm644x.h | 1 + arch/arm/mach-davinci/include/mach/dm646x.h | 1 + 7 files changed, 92 insertions(+), 5 deletions(-) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/devices-da8xx.c b/arch/arm/mach-davinci/devices-da8xx.c index caeb7f4a3a6d..9039221649d4 100644 --- a/arch/arm/mach-davinci/devices-da8xx.c +++ b/arch/arm/mach-davinci/devices-da8xx.c @@ -352,7 +352,7 @@ int __init da8xx_register_watchdog(void) static struct resource da8xx_emac_resources[] = { { .start = DA8XX_EMAC_CPPI_PORT_BASE, - .end = DA8XX_EMAC_CPPI_PORT_BASE + 0x5000 - 1, + .end = DA8XX_EMAC_CPPI_PORT_BASE + SZ_16K - 1, .flags = IORESOURCE_MEM, }, { @@ -396,9 +396,34 @@ static struct platform_device da8xx_emac_device = { .resource = da8xx_emac_resources, }; +static struct resource da8xx_mdio_resources[] = { + { + .start = DA8XX_EMAC_MDIO_BASE, + .end = DA8XX_EMAC_MDIO_BASE + SZ_4K - 1, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device da8xx_mdio_device = { + .name = "davinci_mdio", + .id = 0, + .num_resources = ARRAY_SIZE(da8xx_mdio_resources), + .resource = da8xx_mdio_resources, +}; + int __init da8xx_register_emac(void) { - return platform_device_register(&da8xx_emac_device); + int ret; + + ret = platform_device_register(&da8xx_mdio_device); + if (ret < 0) + return ret; + ret = platform_device_register(&da8xx_emac_device); + if (ret < 0) + return ret; + ret = clk_add_alias(NULL, dev_name(&da8xx_mdio_device.dev), + NULL, &da8xx_emac_device.dev); + return ret; } static struct resource da830_mcasp1_resources[] = { diff --git a/arch/arm/mach-davinci/dm365.c b/arch/arm/mach-davinci/dm365.c index 6b6f4c643709..71f0f9d5c56a 100644 --- a/arch/arm/mach-davinci/dm365.c +++ b/arch/arm/mach-davinci/dm365.c @@ -699,7 +699,7 @@ static struct emac_platform_data dm365_emac_pdata = { static struct resource dm365_emac_resources[] = { { .start = DM365_EMAC_BASE, - .end = DM365_EMAC_BASE + 0x47ff, + .end = DM365_EMAC_BASE + SZ_16K - 1, .flags = IORESOURCE_MEM, }, { @@ -734,6 +734,21 @@ static struct platform_device dm365_emac_device = { .resource = dm365_emac_resources, }; +static struct resource dm365_mdio_resources[] = { + { + .start = DM365_EMAC_MDIO_BASE, + .end = DM365_EMAC_MDIO_BASE + SZ_4K - 1, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device dm365_mdio_device = { + .name = "davinci_mdio", + .id = 0, + .num_resources = ARRAY_SIZE(dm365_mdio_resources), + .resource = dm365_mdio_resources, +}; + static u8 dm365_default_priorities[DAVINCI_N_AINTC_IRQ] = { [IRQ_VDINT0] = 2, [IRQ_VDINT1] = 6, @@ -1220,7 +1235,12 @@ static int __init dm365_init_devices(void) davinci_cfg_reg(DM365_INT_EDMA_CC); platform_device_register(&dm365_edma_device); + + platform_device_register(&dm365_mdio_device); platform_device_register(&dm365_emac_device); + clk_add_alias(NULL, dev_name(&dm365_mdio_device.dev), + NULL, &dm365_emac_device.dev); + /* Add isif clock alias */ clk_add_alias("master", dm365_isif_dev.name, "vpss_master", NULL); platform_device_register(&dm365_vpss_device); diff --git a/arch/arm/mach-davinci/dm644x.c b/arch/arm/mach-davinci/dm644x.c index 40fec315c99a..c103b2c8caff 100644 --- a/arch/arm/mach-davinci/dm644x.c +++ b/arch/arm/mach-davinci/dm644x.c @@ -330,7 +330,7 @@ static struct emac_platform_data dm644x_emac_pdata = { static struct resource dm644x_emac_resources[] = { { .start = DM644X_EMAC_BASE, - .end = DM644X_EMAC_BASE + 0x47ff, + .end = DM644X_EMAC_BASE + SZ_16K - 1, .flags = IORESOURCE_MEM, }, { @@ -350,6 +350,21 @@ static struct platform_device dm644x_emac_device = { .resource = dm644x_emac_resources, }; +static struct resource dm644x_mdio_resources[] = { + { + .start = DM644X_EMAC_MDIO_BASE, + .end = DM644X_EMAC_MDIO_BASE + SZ_4K - 1, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device dm644x_mdio_device = { + .name = "davinci_mdio", + .id = 0, + .num_resources = ARRAY_SIZE(dm644x_mdio_resources), + .resource = dm644x_mdio_resources, +}; + /* * Device specific mux setup * @@ -777,7 +792,12 @@ static int __init dm644x_init_devices(void) clk_add_alias("master", dm644x_ccdc_dev.name, "vpss_master", NULL); clk_add_alias("slave", dm644x_ccdc_dev.name, "vpss_slave", NULL); platform_device_register(&dm644x_edma_device); + + platform_device_register(&dm644x_mdio_device); platform_device_register(&dm644x_emac_device); + clk_add_alias(NULL, dev_name(&dm644x_mdio_device.dev), + NULL, &dm644x_emac_device.dev); + platform_device_register(&dm644x_vpss_device); platform_device_register(&dm644x_ccdc_dev); platform_device_register(&vpfe_capture_dev); diff --git a/arch/arm/mach-davinci/dm646x.c b/arch/arm/mach-davinci/dm646x.c index e4a3df1872ac..8da886bc6df5 100644 --- a/arch/arm/mach-davinci/dm646x.c +++ b/arch/arm/mach-davinci/dm646x.c @@ -366,7 +366,7 @@ static struct emac_platform_data dm646x_emac_pdata = { static struct resource dm646x_emac_resources[] = { { .start = DM646X_EMAC_BASE, - .end = DM646X_EMAC_BASE + 0x47ff, + .end = DM646X_EMAC_BASE + SZ_16K - 1, .flags = IORESOURCE_MEM, }, { @@ -401,6 +401,21 @@ static struct platform_device dm646x_emac_device = { .resource = dm646x_emac_resources, }; +static struct resource dm646x_mdio_resources[] = { + { + .start = DM646X_EMAC_MDIO_BASE, + .end = DM646X_EMAC_MDIO_BASE + SZ_4K - 1, + .flags = IORESOURCE_MEM, + }, +}; + +static struct platform_device dm646x_mdio_device = { + .name = "davinci_mdio", + .id = 0, + .num_resources = ARRAY_SIZE(dm646x_mdio_resources), + .resource = dm646x_mdio_resources, +}; + /* * Device specific mux setup * @@ -897,7 +912,11 @@ static int __init dm646x_init_devices(void) if (!cpu_is_davinci_dm646x()) return 0; + platform_device_register(&dm646x_mdio_device); platform_device_register(&dm646x_emac_device); + clk_add_alias(NULL, dev_name(&dm646x_mdio_device.dev), + NULL, &dm646x_emac_device.dev); + return 0; } postcore_initcall(dm646x_init_devices); diff --git a/arch/arm/mach-davinci/include/mach/dm365.h b/arch/arm/mach-davinci/include/mach/dm365.h index ea5df3b49ec4..dbb5052b6c85 100644 --- a/arch/arm/mach-davinci/include/mach/dm365.h +++ b/arch/arm/mach-davinci/include/mach/dm365.h @@ -21,6 +21,7 @@ #include #define DM365_EMAC_BASE (0x01D07000) +#define DM365_EMAC_MDIO_BASE (DM365_EMAC_BASE + 0x4000) #define DM365_EMAC_CNTRL_OFFSET (0x0000) #define DM365_EMAC_CNTRL_MOD_OFFSET (0x3000) #define DM365_EMAC_CNTRL_RAM_OFFSET (0x1000) diff --git a/arch/arm/mach-davinci/include/mach/dm644x.h b/arch/arm/mach-davinci/include/mach/dm644x.h index 6fca568a0fd2..515911711a29 100644 --- a/arch/arm/mach-davinci/include/mach/dm644x.h +++ b/arch/arm/mach-davinci/include/mach/dm644x.h @@ -28,6 +28,7 @@ #include #define DM644X_EMAC_BASE (0x01C80000) +#define DM644X_EMAC_MDIO_BASE (DM644X_EMAC_BASE + 0x4000) #define DM644X_EMAC_CNTRL_OFFSET (0x0000) #define DM644X_EMAC_CNTRL_MOD_OFFSET (0x1000) #define DM644X_EMAC_CNTRL_RAM_OFFSET (0x2000) diff --git a/arch/arm/mach-davinci/include/mach/dm646x.h b/arch/arm/mach-davinci/include/mach/dm646x.h index 0a27ee9a70e1..1c4dca924ac0 100644 --- a/arch/arm/mach-davinci/include/mach/dm646x.h +++ b/arch/arm/mach-davinci/include/mach/dm646x.h @@ -19,6 +19,7 @@ #include #define DM646X_EMAC_BASE (0x01C80000) +#define DM646X_EMAC_MDIO_BASE (DM646X_EMAC_BASE + 0x4000) #define DM646X_EMAC_CNTRL_OFFSET (0x0000) #define DM646X_EMAC_CNTRL_MOD_OFFSET (0x1000) #define DM646X_EMAC_CNTRL_RAM_OFFSET (0x2000) -- cgit v1.2.1 From 782f2d782771484bb951be1c394ca2128ed7774e Mon Sep 17 00:00:00 2001 From: Cyril Chemparathy Date: Wed, 15 Sep 2010 10:11:25 -0400 Subject: davinci: cleanup mdio arch code and switch to phy_id This patch removes davinci architecture code that has now been rendered useless by the previous patches in the MDIO separation series. In addition, the earlier phy_mask definitions have been replaced with corresponding phy_id definitions. Signed-off-by: Cyril Chemparathy Tested-by: Michael Williamson Tested-by: Caglar Akyuz Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/board-da830-evm.c | 7 ++----- arch/arm/mach-davinci/board-da850-evm.c | 7 ++----- arch/arm/mach-davinci/board-dm365-evm.c | 7 ++----- arch/arm/mach-davinci/board-dm644x-evm.c | 8 ++------ arch/arm/mach-davinci/board-dm646x-evm.c | 7 ++----- arch/arm/mach-davinci/board-mityomapl138.c | 8 ++------ arch/arm/mach-davinci/board-neuros-osd2.c | 7 ++----- arch/arm/mach-davinci/board-sffsdr.c | 7 ++----- arch/arm/mach-davinci/devices-da8xx.c | 2 -- arch/arm/mach-davinci/dm365.c | 1 - arch/arm/mach-davinci/dm644x.c | 1 - arch/arm/mach-davinci/dm646x.c | 1 - arch/arm/mach-davinci/include/mach/dm365.h | 1 - arch/arm/mach-davinci/include/mach/dm644x.h | 1 - arch/arm/mach-davinci/include/mach/dm646x.h | 1 - 15 files changed, 16 insertions(+), 50 deletions(-) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/board-da830-evm.c b/arch/arm/mach-davinci/board-da830-evm.c index ef1ab0b6576e..1bb89d3f9b1f 100644 --- a/arch/arm/mach-davinci/board-da830-evm.c +++ b/arch/arm/mach-davinci/board-da830-evm.c @@ -31,9 +31,7 @@ #include #include -#define DA830_EVM_PHY_MASK 0x0 -#define DA830_EVM_MDIO_FREQUENCY 2200000 /* PHY bus frequency */ - +#define DA830_EVM_PHY_ID "" /* * USB1 VBUS is controlled by GPIO1[15], over-current is reported on GPIO2[4]. */ @@ -558,9 +556,8 @@ static __init void da830_evm_init(void) da830_evm_usb_init(); - soc_info->emac_pdata->phy_mask = DA830_EVM_PHY_MASK; - soc_info->emac_pdata->mdio_max_freq = DA830_EVM_MDIO_FREQUENCY; soc_info->emac_pdata->rmii_en = 1; + soc_info->emac_pdata->phy_id = DA830_EVM_PHY_ID; ret = davinci_cfg_reg_list(da830_cpgmac_pins); if (ret) diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c index ac2297c69a92..5e435b068661 100644 --- a/arch/arm/mach-davinci/board-da850-evm.c +++ b/arch/arm/mach-davinci/board-da850-evm.c @@ -38,9 +38,7 @@ #include #include -#define DA850_EVM_PHY_MASK 0x1 -#define DA850_EVM_MDIO_FREQUENCY 2200000 /* PHY bus frequency */ - +#define DA850_EVM_PHY_ID "0:00" #define DA850_LCD_PWR_PIN GPIO_TO_PIN(2, 8) #define DA850_LCD_BL_PIN GPIO_TO_PIN(2, 15) @@ -678,8 +676,7 @@ static int __init da850_evm_config_emac(void) /* Enable/Disable MII MDIO clock */ gpio_direction_output(DA850_MII_MDIO_CLKEN_PIN, rmii_en); - soc_info->emac_pdata->phy_mask = DA850_EVM_PHY_MASK; - soc_info->emac_pdata->mdio_max_freq = DA850_EVM_MDIO_FREQUENCY; + soc_info->emac_pdata->phy_id = DA850_EVM_PHY_ID; ret = da8xx_register_emac(); if (ret) diff --git a/arch/arm/mach-davinci/board-dm365-evm.c b/arch/arm/mach-davinci/board-dm365-evm.c index bdea2da0b203..a06b84c1b7d8 100644 --- a/arch/arm/mach-davinci/board-dm365-evm.c +++ b/arch/arm/mach-davinci/board-dm365-evm.c @@ -54,9 +54,7 @@ static inline int have_tvp7002(void) return 0; } -#define DM365_EVM_PHY_MASK (0x2) -#define DM365_EVM_MDIO_FREQUENCY (2200000) /* PHY bus frequency */ - +#define DM365_EVM_PHY_ID "0:01" /* * A MAX-II CPLD is used for various board control functions. */ @@ -535,8 +533,7 @@ fail: /* ... and ENET ... */ dm365evm_emac_configure(); - soc_info->emac_pdata->phy_mask = DM365_EVM_PHY_MASK; - soc_info->emac_pdata->mdio_max_freq = DM365_EVM_MDIO_FREQUENCY; + soc_info->emac_pdata->phy_id = DM365_EVM_PHY_ID; resets &= ~BIT(3); /* ... and AIC33 */ diff --git a/arch/arm/mach-davinci/board-dm644x-evm.c b/arch/arm/mach-davinci/board-dm644x-evm.c index 65bb94064feb..44a2f0a59285 100644 --- a/arch/arm/mach-davinci/board-dm644x-evm.c +++ b/arch/arm/mach-davinci/board-dm644x-evm.c @@ -39,9 +39,7 @@ #include #include -#define DM644X_EVM_PHY_MASK (0x2) -#define DM644X_EVM_MDIO_FREQUENCY (2200000) /* PHY bus frequency */ - +#define DM644X_EVM_PHY_ID "0:01" #define LXT971_PHY_ID (0x001378e2) #define LXT971_PHY_MASK (0xfffffff0) @@ -707,9 +705,7 @@ static __init void davinci_evm_init(void) davinci_serial_init(&uart_config); dm644x_init_asp(&dm644x_evm_snd_data); - soc_info->emac_pdata->phy_mask = DM644X_EVM_PHY_MASK; - soc_info->emac_pdata->mdio_max_freq = DM644X_EVM_MDIO_FREQUENCY; - + soc_info->emac_pdata->phy_id = DM644X_EVM_PHY_ID; /* Register the fixup for PHY on DaVinci */ phy_register_fixup_for_uid(LXT971_PHY_ID, LXT971_PHY_MASK, davinci_phy_fixup); diff --git a/arch/arm/mach-davinci/board-dm646x-evm.c b/arch/arm/mach-davinci/board-dm646x-evm.c index 5a29955b2f5c..67669bba922c 100644 --- a/arch/arm/mach-davinci/board-dm646x-evm.c +++ b/arch/arm/mach-davinci/board-dm646x-evm.c @@ -729,9 +729,7 @@ static struct davinci_uart_config uart_config __initdata = { .enabled_uarts = (1 << 0), }; -#define DM646X_EVM_PHY_MASK (0x2) -#define DM646X_EVM_MDIO_FREQUENCY (2200000) /* PHY bus frequency */ - +#define DM646X_EVM_PHY_ID "0:01" /* * The following EDMA channels/slots are not being used by drivers (for * example: Timer, GPIO, UART events etc) on dm646x, hence they are being @@ -784,8 +782,7 @@ static __init void evm_init(void) if (HAS_ATA) davinci_init_ide(); - soc_info->emac_pdata->phy_mask = DM646X_EVM_PHY_MASK; - soc_info->emac_pdata->mdio_max_freq = DM646X_EVM_MDIO_FREQUENCY; + soc_info->emac_pdata->phy_id = DM646X_EVM_PHY_ID; } #define DM646X_EVM_REF_FREQ 27000000 diff --git a/arch/arm/mach-davinci/board-mityomapl138.c b/arch/arm/mach-davinci/board-mityomapl138.c index 84d5aff50de4..6f12a182333b 100644 --- a/arch/arm/mach-davinci/board-mityomapl138.c +++ b/arch/arm/mach-davinci/board-mityomapl138.c @@ -24,9 +24,7 @@ #include #include -#define MITYOMAPL138_PHY_MASK 0x08 /* hardcoded for now */ -#define MITYOMAPL138_MDIO_FREQUENCY (2200000) /* PHY bus frequency */ - +#define MITYOMAPL138_PHY_ID "0:03" static struct davinci_i2c_platform_data mityomap_i2c_0_pdata = { .bus_freq = 100, /* kHz */ .bus_delay = 0, /* usec */ @@ -273,9 +271,7 @@ static void __init mityomapl138_config_emac(void) /* configure the CFGCHIP3 register for RMII or MII */ __raw_writel(val, cfg_chip3_base); - soc_info->emac_pdata->phy_mask = MITYOMAPL138_PHY_MASK; - pr_debug("setting phy_mask to %x\n", soc_info->emac_pdata->phy_mask); - soc_info->emac_pdata->mdio_max_freq = MITYOMAPL138_MDIO_FREQUENCY; + soc_info->emac_pdata->phy_id = MITYOMAPL138_PHY_ID; ret = da8xx_register_emac(); if (ret) diff --git a/arch/arm/mach-davinci/board-neuros-osd2.c b/arch/arm/mach-davinci/board-neuros-osd2.c index 4c30e929bbf9..04a8d16f2224 100644 --- a/arch/arm/mach-davinci/board-neuros-osd2.c +++ b/arch/arm/mach-davinci/board-neuros-osd2.c @@ -39,9 +39,7 @@ #include #include -#define NEUROS_OSD2_PHY_MASK 0x2 -#define NEUROS_OSD2_MDIO_FREQUENCY 2200000 /* PHY bus frequency */ - +#define NEUROS_OSD2_PHY_ID "0:01" #define LXT971_PHY_ID 0x001378e2 #define LXT971_PHY_MASK 0xfffffff0 @@ -252,8 +250,7 @@ static __init void davinci_ntosd2_init(void) davinci_serial_init(&uart_config); dm644x_init_asp(&dm644x_ntosd2_snd_data); - soc_info->emac_pdata->phy_mask = NEUROS_OSD2_PHY_MASK; - soc_info->emac_pdata->mdio_max_freq = NEUROS_OSD2_MDIO_FREQUENCY; + soc_info->emac_pdata->phy_id = NEUROS_OSD2_PHY_ID; davinci_setup_usb(1000, 8); /* diff --git a/arch/arm/mach-davinci/board-sffsdr.c b/arch/arm/mach-davinci/board-sffsdr.c index 23e664a1a802..ab4292d4f80b 100644 --- a/arch/arm/mach-davinci/board-sffsdr.c +++ b/arch/arm/mach-davinci/board-sffsdr.c @@ -42,9 +42,7 @@ #include #include -#define SFFSDR_PHY_MASK (0x2) -#define SFFSDR_MDIO_FREQUENCY (2200000) /* PHY bus frequency */ - +#define SFFSDR_PHY_ID "0:01" static struct mtd_partition davinci_sffsdr_nandflash_partition[] = { /* U-Boot Environment: Block 0 * UBL: Block 1 @@ -143,8 +141,7 @@ static __init void davinci_sffsdr_init(void) ARRAY_SIZE(davinci_sffsdr_devices)); sffsdr_init_i2c(); davinci_serial_init(&uart_config); - soc_info->emac_pdata->phy_mask = SFFSDR_PHY_MASK; - soc_info->emac_pdata->mdio_max_freq = SFFSDR_MDIO_FREQUENCY; + soc_info->emac_pdata->phy_id = SFFSDR_PHY_ID; davinci_setup_usb(0, 0); /* We support only peripheral mode. */ /* mux VLYNQ pins */ diff --git a/arch/arm/mach-davinci/devices-da8xx.c b/arch/arm/mach-davinci/devices-da8xx.c index 9039221649d4..9eec63070e0c 100644 --- a/arch/arm/mach-davinci/devices-da8xx.c +++ b/arch/arm/mach-davinci/devices-da8xx.c @@ -42,7 +42,6 @@ #define DA8XX_EMAC_CTRL_REG_OFFSET 0x3000 #define DA8XX_EMAC_MOD_REG_OFFSET 0x2000 #define DA8XX_EMAC_RAM_OFFSET 0x0000 -#define DA8XX_MDIO_REG_OFFSET 0x4000 #define DA8XX_EMAC_CTRL_RAM_SIZE SZ_8K void __iomem *da8xx_syscfg0_base; @@ -381,7 +380,6 @@ struct emac_platform_data da8xx_emac_pdata = { .ctrl_reg_offset = DA8XX_EMAC_CTRL_REG_OFFSET, .ctrl_mod_reg_offset = DA8XX_EMAC_MOD_REG_OFFSET, .ctrl_ram_offset = DA8XX_EMAC_RAM_OFFSET, - .mdio_reg_offset = DA8XX_MDIO_REG_OFFSET, .ctrl_ram_size = DA8XX_EMAC_CTRL_RAM_SIZE, .version = EMAC_VERSION_2, }; diff --git a/arch/arm/mach-davinci/dm365.c b/arch/arm/mach-davinci/dm365.c index 71f0f9d5c56a..240f392e18a8 100644 --- a/arch/arm/mach-davinci/dm365.c +++ b/arch/arm/mach-davinci/dm365.c @@ -691,7 +691,6 @@ static struct emac_platform_data dm365_emac_pdata = { .ctrl_reg_offset = DM365_EMAC_CNTRL_OFFSET, .ctrl_mod_reg_offset = DM365_EMAC_CNTRL_MOD_OFFSET, .ctrl_ram_offset = DM365_EMAC_CNTRL_RAM_OFFSET, - .mdio_reg_offset = DM365_EMAC_MDIO_OFFSET, .ctrl_ram_size = DM365_EMAC_CNTRL_RAM_SIZE, .version = EMAC_VERSION_2, }; diff --git a/arch/arm/mach-davinci/dm644x.c b/arch/arm/mach-davinci/dm644x.c index c103b2c8caff..41b7a95f22d3 100644 --- a/arch/arm/mach-davinci/dm644x.c +++ b/arch/arm/mach-davinci/dm644x.c @@ -322,7 +322,6 @@ static struct emac_platform_data dm644x_emac_pdata = { .ctrl_reg_offset = DM644X_EMAC_CNTRL_OFFSET, .ctrl_mod_reg_offset = DM644X_EMAC_CNTRL_MOD_OFFSET, .ctrl_ram_offset = DM644X_EMAC_CNTRL_RAM_OFFSET, - .mdio_reg_offset = DM644X_EMAC_MDIO_OFFSET, .ctrl_ram_size = DM644X_EMAC_CNTRL_RAM_SIZE, .version = EMAC_VERSION_1, }; diff --git a/arch/arm/mach-davinci/dm646x.c b/arch/arm/mach-davinci/dm646x.c index 8da886bc6df5..08db90f14287 100644 --- a/arch/arm/mach-davinci/dm646x.c +++ b/arch/arm/mach-davinci/dm646x.c @@ -358,7 +358,6 @@ static struct emac_platform_data dm646x_emac_pdata = { .ctrl_reg_offset = DM646X_EMAC_CNTRL_OFFSET, .ctrl_mod_reg_offset = DM646X_EMAC_CNTRL_MOD_OFFSET, .ctrl_ram_offset = DM646X_EMAC_CNTRL_RAM_OFFSET, - .mdio_reg_offset = DM646X_EMAC_MDIO_OFFSET, .ctrl_ram_size = DM646X_EMAC_CNTRL_RAM_SIZE, .version = EMAC_VERSION_2, }; diff --git a/arch/arm/mach-davinci/include/mach/dm365.h b/arch/arm/mach-davinci/include/mach/dm365.h index dbb5052b6c85..2563bf4e93a1 100644 --- a/arch/arm/mach-davinci/include/mach/dm365.h +++ b/arch/arm/mach-davinci/include/mach/dm365.h @@ -25,7 +25,6 @@ #define DM365_EMAC_CNTRL_OFFSET (0x0000) #define DM365_EMAC_CNTRL_MOD_OFFSET (0x3000) #define DM365_EMAC_CNTRL_RAM_OFFSET (0x1000) -#define DM365_EMAC_MDIO_OFFSET (0x4000) #define DM365_EMAC_CNTRL_RAM_SIZE (0x2000) /* Base of key scan register bank */ diff --git a/arch/arm/mach-davinci/include/mach/dm644x.h b/arch/arm/mach-davinci/include/mach/dm644x.h index 515911711a29..5a1b26d4e68b 100644 --- a/arch/arm/mach-davinci/include/mach/dm644x.h +++ b/arch/arm/mach-davinci/include/mach/dm644x.h @@ -32,7 +32,6 @@ #define DM644X_EMAC_CNTRL_OFFSET (0x0000) #define DM644X_EMAC_CNTRL_MOD_OFFSET (0x1000) #define DM644X_EMAC_CNTRL_RAM_OFFSET (0x2000) -#define DM644X_EMAC_MDIO_OFFSET (0x4000) #define DM644X_EMAC_CNTRL_RAM_SIZE (0x2000) #define DM644X_ASYNC_EMIF_CONTROL_BASE 0x01E00000 diff --git a/arch/arm/mach-davinci/include/mach/dm646x.h b/arch/arm/mach-davinci/include/mach/dm646x.h index 1c4dca924ac0..7a27f3f13913 100644 --- a/arch/arm/mach-davinci/include/mach/dm646x.h +++ b/arch/arm/mach-davinci/include/mach/dm646x.h @@ -23,7 +23,6 @@ #define DM646X_EMAC_CNTRL_OFFSET (0x0000) #define DM646X_EMAC_CNTRL_MOD_OFFSET (0x1000) #define DM646X_EMAC_CNTRL_RAM_OFFSET (0x2000) -#define DM646X_EMAC_MDIO_OFFSET (0x4000) #define DM646X_EMAC_CNTRL_RAM_SIZE (0x2000) #define DM646X_ASYNC_EMIF_CONTROL_BASE 0x20008000 -- cgit v1.2.1 From d45b1ed4e47d2f585d2acdf5b957bfc5ff465aab Mon Sep 17 00:00:00 2001 From: Cyril Chemparathy Date: Mon, 20 Sep 2010 12:26:41 -0400 Subject: davinci: add tnetv107x keypad platform device This patch adds a platform device definition for tnetv107x's keypad controller. Signed-off-by: Cyril Chemparathy Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/devices-tnetv107x.c | 30 ++++++++++++++++++++++++++ arch/arm/mach-davinci/include/mach/tnetv107x.h | 3 +++ 2 files changed, 33 insertions(+) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/devices-tnetv107x.c b/arch/arm/mach-davinci/devices-tnetv107x.c index 2718a3a90dff..086269fc2ee5 100644 --- a/arch/arm/mach-davinci/devices-tnetv107x.c +++ b/arch/arm/mach-davinci/devices-tnetv107x.c @@ -33,6 +33,7 @@ #define TNETV107X_WDOG_BASE 0x08086700 #define TNETV107X_SDIO0_BASE 0x08088700 #define TNETV107X_SDIO1_BASE 0x08088800 +#define TNETV107X_KEYPAD_BASE 0x08088a00 #define TNETV107X_ASYNC_EMIF_CNTRL_BASE 0x08200000 #define TNETV107X_ASYNC_EMIF_DATA_CE0_BASE 0x30000000 #define TNETV107X_ASYNC_EMIF_DATA_CE1_BASE 0x40000000 @@ -298,6 +299,30 @@ static int __init nand_init(int chipsel, struct davinci_nand_pdata *data) return platform_device_register(pdev); } +static struct resource keypad_resources[] = { + { + .start = TNETV107X_KEYPAD_BASE, + .end = TNETV107X_KEYPAD_BASE + 0xff, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_TNETV107X_KEYPAD, + .flags = IORESOURCE_IRQ, + .name = "press", + }, + { + .start = IRQ_TNETV107X_KEYPAD_FREE, + .flags = IORESOURCE_IRQ, + .name = "release", + }, +}; + +static struct platform_device keypad_device = { + .name = "tnetv107x-keypad", + .num_resources = ARRAY_SIZE(keypad_resources), + .resource = keypad_resources, +}; + void __init tnetv107x_devices_init(struct tnetv107x_device_info *info) { int i; @@ -317,4 +342,9 @@ void __init tnetv107x_devices_init(struct tnetv107x_device_info *info) for (i = 0; i < 4; i++) if (info->nand_config[i]) nand_init(i, info->nand_config[i]); + + if (info->keypad_config) { + keypad_device.dev.platform_data = info->keypad_config; + platform_device_register(&keypad_device); + } } diff --git a/arch/arm/mach-davinci/include/mach/tnetv107x.h b/arch/arm/mach-davinci/include/mach/tnetv107x.h index c72064733123..5a681d880dcb 100644 --- a/arch/arm/mach-davinci/include/mach/tnetv107x.h +++ b/arch/arm/mach-davinci/include/mach/tnetv107x.h @@ -33,6 +33,8 @@ #ifndef __ASSEMBLY__ #include +#include + #include #include #include @@ -41,6 +43,7 @@ struct tnetv107x_device_info { struct davinci_uart_config *serial_config; struct davinci_mmc_config *mmc_config[2]; /* 2 controllers */ struct davinci_nand_pdata *nand_config[4]; /* 4 chipsels */ + struct matrix_keypad_platform_data *keypad_config; }; extern struct platform_device tnetv107x_wdt_device; -- cgit v1.2.1 From a1b4440314edca8e2016f2819d4655453e6aff44 Mon Sep 17 00:00:00 2001 From: Cyril Chemparathy Date: Mon, 20 Sep 2010 12:26:42 -0400 Subject: davinci: add keypad config for tnetv107x evm board This patch adds evm board specific keymap definitions and controller configuration data for on-chip keypad controller on tnetv107x silicon. Signed-off-by: Cyril Chemparathy Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/board-tnetv107x-evm.c | 56 +++++++++++++++++++++++++++++ 1 file changed, 56 insertions(+) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/board-tnetv107x-evm.c b/arch/arm/mach-davinci/board-tnetv107x-evm.c index fe2a9d9c8bb7..5afa8fc48e7b 100644 --- a/arch/arm/mach-davinci/board-tnetv107x-evm.c +++ b/arch/arm/mach-davinci/board-tnetv107x-evm.c @@ -23,6 +23,9 @@ #include #include #include +#include +#include + #include #include @@ -141,10 +144,63 @@ static struct davinci_uart_config serial_config __initconst = { .enabled_uarts = BIT(1), }; +static const uint32_t keymap[] = { + KEY(0, 0, KEY_NUMERIC_1), + KEY(0, 1, KEY_NUMERIC_2), + KEY(0, 2, KEY_NUMERIC_3), + KEY(0, 3, KEY_FN_F1), + KEY(0, 4, KEY_MENU), + + KEY(1, 0, KEY_NUMERIC_4), + KEY(1, 1, KEY_NUMERIC_5), + KEY(1, 2, KEY_NUMERIC_6), + KEY(1, 3, KEY_UP), + KEY(1, 4, KEY_FN_F2), + + KEY(2, 0, KEY_NUMERIC_7), + KEY(2, 1, KEY_NUMERIC_8), + KEY(2, 2, KEY_NUMERIC_9), + KEY(2, 3, KEY_LEFT), + KEY(2, 4, KEY_ENTER), + + KEY(3, 0, KEY_NUMERIC_STAR), + KEY(3, 1, KEY_NUMERIC_0), + KEY(3, 2, KEY_NUMERIC_POUND), + KEY(3, 3, KEY_DOWN), + KEY(3, 4, KEY_RIGHT), + + KEY(4, 0, KEY_FN_F3), + KEY(4, 1, KEY_FN_F4), + KEY(4, 2, KEY_MUTE), + KEY(4, 3, KEY_HOME), + KEY(4, 4, KEY_BACK), + + KEY(5, 0, KEY_VOLUMEDOWN), + KEY(5, 1, KEY_VOLUMEUP), + KEY(5, 2, KEY_F1), + KEY(5, 3, KEY_F2), + KEY(5, 4, KEY_F3), +}; + +static const struct matrix_keymap_data keymap_data = { + .keymap = keymap, + .keymap_size = ARRAY_SIZE(keymap), +}; + +static struct matrix_keypad_platform_data keypad_config = { + .keymap_data = &keymap_data, + .num_row_gpios = 6, + .num_col_gpios = 5, + .debounce_ms = 0, /* minimum */ + .active_low = 0, /* pull up realization */ + .no_autorepeat = 0, +}; + static struct tnetv107x_device_info evm_device_info __initconst = { .serial_config = &serial_config, .mmc_config[1] = &mmc_config, /* controller 1 */ .nand_config[0] = &nand_config, /* chip select 0 */ + .keypad_config = &keypad_config, }; static __init void tnetv107x_evm_board_init(void) -- cgit v1.2.1 From 1f4640ae7c299ce87968cb3923c5f85254d68c37 Mon Sep 17 00:00:00 2001 From: Cyril Chemparathy Date: Mon, 20 Sep 2010 12:26:44 -0400 Subject: davinci: add tnetv107x touchscreen platform device This patch adds a platform device definition for tnetv107x's touchscreen controller. Signed-off-by: Cyril Chemparathy Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/devices-tnetv107x.c | 20 ++++++++++++++++++++ 1 file changed, 20 insertions(+) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/devices-tnetv107x.c b/arch/arm/mach-davinci/devices-tnetv107x.c index 086269fc2ee5..c9a86d8130d1 100644 --- a/arch/arm/mach-davinci/devices-tnetv107x.c +++ b/arch/arm/mach-davinci/devices-tnetv107x.c @@ -31,6 +31,7 @@ #define TNETV107X_TPTC0_BASE 0x01c10000 #define TNETV107X_TPTC1_BASE 0x01c10400 #define TNETV107X_WDOG_BASE 0x08086700 +#define TNETV107X_TSC_BASE 0x08088500 #define TNETV107X_SDIO0_BASE 0x08088700 #define TNETV107X_SDIO1_BASE 0x08088800 #define TNETV107X_KEYPAD_BASE 0x08088a00 @@ -323,12 +324,31 @@ static struct platform_device keypad_device = { .resource = keypad_resources, }; +static struct resource tsc_resources[] = { + { + .start = TNETV107X_TSC_BASE, + .end = TNETV107X_TSC_BASE + 0xff, + .flags = IORESOURCE_MEM, + }, + { + .start = IRQ_TNETV107X_TSC, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device tsc_device = { + .name = "tnetv107x-ts", + .num_resources = ARRAY_SIZE(tsc_resources), + .resource = tsc_resources, +}; + void __init tnetv107x_devices_init(struct tnetv107x_device_info *info) { int i; platform_device_register(&edma_device); platform_device_register(&tnetv107x_wdt_device); + platform_device_register(&tsc_device); if (info->serial_config) davinci_serial_init(info->serial_config); -- cgit v1.2.1 From 2a7dae04f3a5966ade5086ebd2e09f170fd0e085 Mon Sep 17 00:00:00 2001 From: Michael Williamson Date: Fri, 17 Sep 2010 09:56:06 -0400 Subject: davinci: MityDSP-L138/MityARM-1808 read MAC address from I2C Prom For the MityDSP-L138/MityARM-1808 SOMS, read the factory assigned MAC address from the onboard I2C EPROM and assign it to the emac device during platform initialization. Signed-off-by: Michael Williamson Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/board-mityomapl138.c | 62 ++++++++++++++++++++++++++++++ 1 file changed, 62 insertions(+) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/board-mityomapl138.c b/arch/arm/mach-davinci/board-mityomapl138.c index 6f12a182333b..65f7501984db 100644 --- a/arch/arm/mach-davinci/board-mityomapl138.c +++ b/arch/arm/mach-davinci/board-mityomapl138.c @@ -15,6 +15,8 @@ #include #include #include +#include +#include #include #include @@ -25,6 +27,65 @@ #include #define MITYOMAPL138_PHY_ID "0:03" + +#define FACTORY_CONFIG_MAGIC 0x012C0138 +#define FACTORY_CONFIG_VERSION 0x00010001 + +/* Data Held in On-Board I2C device */ +struct factory_config { + u32 magic; + u32 version; + u8 mac[6]; + u32 fpga_type; + u32 spare; + u32 serialnumber; + char partnum[32]; +}; + +static struct factory_config factory_config; + +static void read_factory_config(struct memory_accessor *a, void *context) +{ + int ret; + struct davinci_soc_info *soc_info = &davinci_soc_info; + + ret = a->read(a, (char *)&factory_config, 0, sizeof(factory_config)); + if (ret != sizeof(struct factory_config)) { + pr_warning("MityOMAPL138: Read Factory Config Failed: %d\n", + ret); + return; + } + + if (factory_config.magic != FACTORY_CONFIG_MAGIC) { + pr_warning("MityOMAPL138: Factory Config Magic Wrong (%X)\n", + factory_config.magic); + return; + } + + if (factory_config.version != FACTORY_CONFIG_VERSION) { + pr_warning("MityOMAPL138: Factory Config Version Wrong (%X)\n", + factory_config.version); + return; + } + + pr_info("MityOMAPL138: Found MAC = %pM\n", factory_config.mac); + pr_info("MityOMAPL138: Part Number = %s\n", factory_config.partnum); + if (is_valid_ether_addr(factory_config.mac)) + memcpy(soc_info->emac_pdata->mac_addr, + factory_config.mac, ETH_ALEN); + else + pr_warning("MityOMAPL138: Invalid MAC found " + "in factory config block\n"); +} + +static struct at24_platform_data mityomapl138_fd_chip = { + .byte_len = 256, + .page_size = 8, + .flags = AT24_FLAG_READONLY | AT24_FLAG_IRUGO, + .setup = read_factory_config, + .context = NULL, +}; + static struct davinci_i2c_platform_data mityomap_i2c_0_pdata = { .bus_freq = 100, /* kHz */ .bus_delay = 0, /* usec */ @@ -151,6 +212,7 @@ static struct i2c_board_info __initdata mityomap_tps65023_info[] = { }, { I2C_BOARD_INFO("24c02", 0x50), + .platform_data = &mityomapl138_fd_chip, }, }; -- cgit v1.2.1 From 6c18c91b3a6db6169998b54df12c9d53e74999f3 Mon Sep 17 00:00:00 2001 From: Victor Rodriguez Date: Thu, 23 Sep 2010 11:28:40 -0500 Subject: davinci: Initial support for Omapl138-Hawkboard This patch adds initial support for the Hawkboard-L138 system It is under the machine name "omapl138_hawkboard". This system is based on the da850 davinci CPU architecture. Information on these system may be found at http://www.hawkboard.org. Basic support for the UART console is included in this patch. It's tested with latest Angstrom File Systems like ramdisk from http://alturl.com/imb45. Signed-off-by: Victor Rodriguez Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/Kconfig | 8 ++++ arch/arm/mach-davinci/Makefile | 1 + arch/arm/mach-davinci/board-omapl138-hawk.c | 64 +++++++++++++++++++++++++ arch/arm/mach-davinci/include/mach/uncompress.h | 1 + 4 files changed, 74 insertions(+) create mode 100644 arch/arm/mach-davinci/board-omapl138-hawk.c (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/Kconfig b/arch/arm/mach-davinci/Kconfig index 9aca60cb4241..b77b860b36d7 100644 --- a/arch/arm/mach-davinci/Kconfig +++ b/arch/arm/mach-davinci/Kconfig @@ -193,6 +193,14 @@ config MACH_MITYOMAPL138 System on Module. Information on this SoM may be found at http://www.mitydsp.com +config MACH_OMAPL138_HAWKBOARD + bool "TI AM1808 / OMAPL-138 Hawkboard platform" + depends on ARCH_DAVINCI_DA850 + help + Say Y here to select the TI AM1808 / OMAPL-138 Hawkboard platform . + Information of this board may be found at + http://www.hawkboard.org/ + config DAVINCI_MUX bool "DAVINCI multiplexing support" depends on ARCH_DAVINCI diff --git a/arch/arm/mach-davinci/Makefile b/arch/arm/mach-davinci/Makefile index a7a70d1ba363..0b87a1ca2bb3 100644 --- a/arch/arm/mach-davinci/Makefile +++ b/arch/arm/mach-davinci/Makefile @@ -34,6 +34,7 @@ obj-$(CONFIG_MACH_DAVINCI_DA830_EVM) += board-da830-evm.o obj-$(CONFIG_MACH_DAVINCI_DA850_EVM) += board-da850-evm.o obj-$(CONFIG_MACH_TNETV107X) += board-tnetv107x-evm.o obj-$(CONFIG_MACH_MITYOMAPL138) += board-mityomapl138.o +obj-$(CONFIG_MACH_OMAPL138_HAWKBOARD) += board-omapl138-hawk.o # Power Management obj-$(CONFIG_CPU_FREQ) += cpufreq.o diff --git a/arch/arm/mach-davinci/board-omapl138-hawk.c b/arch/arm/mach-davinci/board-omapl138-hawk.c new file mode 100644 index 000000000000..c472dd88ad91 --- /dev/null +++ b/arch/arm/mach-davinci/board-omapl138-hawk.c @@ -0,0 +1,64 @@ +/* + * Hawkboard.org based on TI's OMAP-L138 Platform + * + * Initial code: Syed Mohammed Khasim + * + * Copyright (C) 2009 Texas Instruments Incorporated - http://www.ti.com + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of + * any kind, whether express or implied. + */ +#include +#include +#include +#include + +#include +#include + +#include +#include + +static struct davinci_uart_config omapl138_hawk_uart_config __initdata = { + .enabled_uarts = 0x7, +}; + +static __init void omapl138_hawk_init(void) +{ + int ret; + + davinci_serial_init(&omapl138_hawk_uart_config); + + ret = da8xx_register_watchdog(); + if (ret) + pr_warning("omapl138_hawk_init: " + "watchdog registration failed: %d\n", + ret); +} + +#ifdef CONFIG_SERIAL_8250_CONSOLE +static int __init omapl138_hawk_console_init(void) +{ + if (!machine_is_omapl138_hawkboard()) + return 0; + + return add_preferred_console("ttyS", 2, "115200"); +} +console_initcall(omapl138_hawk_console_init); +#endif + +static void __init omapl138_hawk_map_io(void) +{ + da850_init(); +} + +MACHINE_START(OMAPL138_HAWKBOARD, "AM18x/OMAP-L138 Hawkboard") + .phys_io = IO_PHYS, + .io_pg_offst = (__IO_ADDRESS(IO_PHYS) >> 18) & 0xfffc, + .boot_params = (DA8XX_DDR_BASE + 0x100), + .map_io = omapl138_hawk_map_io, + .init_irq = cp_intc_init, + .timer = &davinci_timer, + .init_machine = omapl138_hawk_init, +MACHINE_END diff --git a/arch/arm/mach-davinci/include/mach/uncompress.h b/arch/arm/mach-davinci/include/mach/uncompress.h index d370391d6f31..47723e8d75a4 100644 --- a/arch/arm/mach-davinci/include/mach/uncompress.h +++ b/arch/arm/mach-davinci/include/mach/uncompress.h @@ -89,6 +89,7 @@ static inline void __arch_decomp_setup(unsigned long arch_id) DEBUG_LL_DA8XX(davinci_da830_evm, 2); DEBUG_LL_DA8XX(davinci_da850_evm, 2); DEBUG_LL_DA8XX(mityomapl138, 1); + DEBUG_LL_DA8XX(omapl138_hawkboard, 2); /* TNETV107x boards */ DEBUG_LL_TNETV107X(tnetv107x, 1); -- cgit v1.2.1 From 156a0f8ecb05bae53f1652ddb151c74315a615fb Mon Sep 17 00:00:00 2001 From: Nicolas Kaiser Date: Mon, 4 Oct 2010 12:39:47 +0200 Subject: arm/davinci: remove duplicated include Remove duplicated include. Signed-off-by: Nicolas Kaiser Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/board-da850-evm.c | 1 - 1 file changed, 1 deletion(-) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c index 5e435b068661..ef97c7f76de5 100644 --- a/arch/arm/mach-davinci/board-da850-evm.c +++ b/arch/arm/mach-davinci/board-da850-evm.c @@ -26,7 +26,6 @@ #include #include #include -#include #include #include -- cgit v1.2.1 From 8939b3504dc35224cb9c88e5af925b22ea9eee71 Mon Sep 17 00:00:00 2001 From: Sekhar Nori Date: Tue, 12 Oct 2010 10:25:22 +0530 Subject: davinci: mityomapl138: make file local data static Most of the regulator data structures are local to the board file, but not made static. Fix this. Also make the nand partition table static. This gets rid of all the sparse warnings for this file. Signed-off-by: Sekhar Nori Signed-off-by: Kevin Hilman --- arch/arm/mach-davinci/board-mityomapl138.c | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) (limited to 'arch/arm/mach-davinci') diff --git a/arch/arm/mach-davinci/board-mityomapl138.c b/arch/arm/mach-davinci/board-mityomapl138.c index 65f7501984db..194a15ff2b4a 100644 --- a/arch/arm/mach-davinci/board-mityomapl138.c +++ b/arch/arm/mach-davinci/board-mityomapl138.c @@ -93,14 +93,14 @@ static struct davinci_i2c_platform_data mityomap_i2c_0_pdata = { /* TPS65023 voltage regulator support */ /* 1.2V Core */ -struct regulator_consumer_supply tps65023_dcdc1_consumers[] = { +static struct regulator_consumer_supply tps65023_dcdc1_consumers[] = { { .supply = "cvdd", }, }; /* 1.8V */ -struct regulator_consumer_supply tps65023_dcdc2_consumers[] = { +static struct regulator_consumer_supply tps65023_dcdc2_consumers[] = { { .supply = "usb0_vdda18", }, @@ -116,7 +116,7 @@ struct regulator_consumer_supply tps65023_dcdc2_consumers[] = { }; /* 1.2V */ -struct regulator_consumer_supply tps65023_dcdc3_consumers[] = { +static struct regulator_consumer_supply tps65023_dcdc3_consumers[] = { { .supply = "sata_vdd", }, @@ -132,20 +132,20 @@ struct regulator_consumer_supply tps65023_dcdc3_consumers[] = { }; /* 1.8V Aux LDO, not used */ -struct regulator_consumer_supply tps65023_ldo1_consumers[] = { +static struct regulator_consumer_supply tps65023_ldo1_consumers[] = { { .supply = "1.8v_aux", }, }; /* FPGA VCC Aux (2.5 or 3.3) LDO */ -struct regulator_consumer_supply tps65023_ldo2_consumers[] = { +static struct regulator_consumer_supply tps65023_ldo2_consumers[] = { { .supply = "vccaux", }, }; -struct regulator_init_data tps65023_regulator_data[] = { +static struct regulator_init_data tps65023_regulator_data[] = { /* dcdc1 */ { .constraints = { @@ -226,7 +226,7 @@ static int __init pmic_tps65023_init(void) * MityDSP-L138 includes a 256 MByte large-page NAND flash * (128K blocks). */ -struct mtd_partition mityomapl138_nandflash_partition[] = { +static struct mtd_partition mityomapl138_nandflash_partition[] = { { .name = "rootfs", .offset = 0, -- cgit v1.2.1