From e3ba22db09408baee721897fb1b50e16f071d916 Mon Sep 17 00:00:00 2001 From: Andrew Victor Date: Sat, 24 May 2008 17:06:45 +0100 Subject: [ARM] 5056/1: [AT91] Cleanup YL9200 board file Cleanup the YL9200 board-support file. Other things fixed are: - Use new-style UART initialization - Register all LEDs as gpio_leds. - NOR Flash error noted in comments fixed by increasing YL9200_FLASH_SIZE - The only I2C device is the AT24C eeprom. - Setup of NWAIT pin and programming of SMC controller for the LCD/VGA. - Configure touchscreen interrupt pin. Also adding the board to the KConfig and Makefile. Signed-off-by: Andrew Victor Signed-off-by: Russell King --- arch/arm/mach-at91/Kconfig | 6 + arch/arm/mach-at91/Makefile | 1 + arch/arm/mach-at91/board-yl-9200.c | 853 +++++++++++++++++-------------------- 3 files changed, 394 insertions(+), 466 deletions(-) (limited to 'arch/arm/mach-at91') diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index 0fc07b6db749..3d549a9afe1d 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -126,6 +126,12 @@ config MACH_ECBAT91 Select this if you are using emQbit's ECB_AT91 board. +config MACH_YL9200 + bool "ucDragon YL-9200" + depends on ARCH_AT91RM9200 + help + Select this if you are using the ucDragon YL-9200 board. + endif # ---------------------------------------------------------- diff --git a/arch/arm/mach-at91/Makefile b/arch/arm/mach-at91/Makefile index 8d9bc0153b18..995be14b2c42 100644 --- a/arch/arm/mach-at91/Makefile +++ b/arch/arm/mach-at91/Makefile @@ -30,6 +30,7 @@ obj-$(CONFIG_MACH_ATEB9200) += board-eb9200.o obj-$(CONFIG_MACH_KAFA) += board-kafa.o obj-$(CONFIG_MACH_PICOTUX2XX) += board-picotux200.o obj-$(CONFIG_MACH_ECBAT91) += board-ecbat91.o +obj-$(CONFIG_MACH_YL9200) += board-yl-9200.o # AT91SAM9260 board-specific support obj-$(CONFIG_MACH_AT91SAM9260EK) += board-sam9260ek.o diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c index b5717108991d..7079050ab88d 100755 --- a/arch/arm/mach-at91/board-yl-9200.c +++ b/arch/arm/mach-at91/board-yl-9200.c @@ -1,11 +1,10 @@ /* * linux/arch/arm/mach-at91/board-yl-9200.c * - * Adapted from: - *various board files in - * /arch/arm/mach-at91 - * modifications to convert to YL-9200 platform - * Copyright (C) 2007 S.Birtles + * Adapted from various board files in arch/arm/mach-at91 + * + * Modifications for YL-9200 platform: + * Copyright (C) 2007 S. Birtles * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -26,13 +25,14 @@ #include #include #include +#include #include #include -/*#include */ #include #include +#include +#include -/*#include */ #include #include #include @@ -45,179 +45,108 @@ #include #include #include -#include -#include #include "generic.h" -#include -#define YL_9200_FLASH_BASE AT91_CHIPSELECT_0 -#define YL_9200_FLASH_SIZE 0x800000 -/* - * Serial port configuration. - * 0 .. 3 = USART0 .. USART3 - * 4 = DBGU - *atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL - *atmel_usart.1: ttyS1 at MMIO 0xfffc0000 (irq = 6) is a ATMEL_SERIAL - *atmel_usart.2: ttyS2 at MMIO 0xfffc4000 (irq = 7) is a ATMEL_SERIAL - *atmel_usart.3: ttyS3 at MMIO 0xfffc8000 (irq = 8) is a ATMEL_SERIAL - *atmel_usart.4: ttyS4 at MMIO 0xfffcc000 (irq = 9) is a ATMEL_SERIAL - * on the YL-9200 we are sitting at the following - *ttyS0 at MMIO 0xfefff200 (irq = 1) is a AT91_SERIAL - *ttyS1 at MMIO 0xfefc4000 (irq = 7) is a AT91_SERIAL - */ +static void __init yl9200_map_io(void) +{ + /* Initialize processor: 18.432 MHz crystal */ + at91rm9200_initialize(18432000, AT91RM9200_PQFP); -/* extern void __init yl_9200_add_device_sounder(struct gpio_sounder *sounders, int nr);*/ + /* Setup the LEDs D2=PB17 (timer), D3=PB16 (cpu) */ + at91_init_leds(AT91_PIN_PB16, AT91_PIN_PB17); -static struct at91_uart_config __initdata yl_9200_uart_config = { - .console_tty = 0, /* ttyS0 */ - .nr_tty = 3, - .tty_map = { 4, 1, 0, -1, -1 } /* ttyS0, ..., ttyS4 */ -}; + /* DBGU on ttyS0. (Rx & Tx only) */ + at91_register_uart(0, 0, 0); -static void __init yl_9200_map_io(void) -{ - /* Initialize processor: 18.432 MHz crystal */ - /*Also initialises register clocks & gpio*/ - at91rm9200_initialize(18432000, AT91RM9200_PQFP); /*we have a 3 bank system*/ + /* USART1 on ttyS1. (Rx, Tx, CTS, RTS, DTR, DSR, DCD, RI) */ + at91_register_uart(AT91RM9200_ID_US1, 1, ATMEL_UART_CTS | ATMEL_UART_RTS + | ATMEL_UART_DTR | ATMEL_UART_DSR | ATMEL_UART_DCD + | ATMEL_UART_RI); - /* Setup the serial ports and console */ - at91_init_serial(&yl_9200_uart_config); + /* USART0 on ttyS2. (Rx & Tx only to JP3) */ + at91_register_uart(AT91RM9200_ID_US0, 2, 0); - /* Setup the LEDs D2=PB17,D3=PB16 */ - at91_init_leds(AT91_PIN_PB16,AT91_PIN_PB17); /*cpu-led,timer-led*/ + /* USART3 on ttyS3. (Rx, Tx, RTS - RS485 interface) */ + at91_register_uart(AT91RM9200_ID_US3, 3, ATMEL_UART_RTS); + + /* set serial console to ttyS0 (ie, DBGU) */ + at91_set_serial_console(0); } -static void __init yl_9200_init_irq(void) +static void __init yl9200_init_irq(void) { at91rm9200_init_interrupts(NULL); } -static struct at91_eth_data __initdata yl_9200_eth_data = { - .phy_irq_pin = AT91_PIN_PB28, - .is_rmii = 1, -}; -static struct at91_usbh_data __initdata yl_9200_usbh_data = { - .ports = 1, /* this should be 1 not 2 for the Yl9200*/ +/* + * LEDs + */ +static struct gpio_led yl9200_leds[] = { + { /* D2 */ + .name = "led2", + .gpio = AT91_PIN_PB17, + .active_low = 1, + .default_trigger = "timer", + }, + { /* D3 */ + .name = "led3", + .gpio = AT91_PIN_PB16, + .active_low = 1, + .default_trigger = "heartbeat", + }, + { /* D4 */ + .name = "led4", + .gpio = AT91_PIN_PB15, + .active_low = 1, + }, + { /* D5 */ + .name = "led5", + .gpio = AT91_PIN_PB8, + .active_low = 1, + } }; -static struct at91_udc_data __initdata yl_9200_udc_data = { -/*on sheet 7 Schemitic rev 1.0*/ - .pullup_pin = AT91_PIN_PC4, - .vbus_pin= AT91_PIN_PC5, - .pullup_active_low = 1, /*ACTIVE LOW!! due to PNP transistor on page 7*/ - -}; /* -static struct at91_cf_data __initdata yl_9200_cf_data = { -TODO S.BIRTLES - .det_pin = AT91_PIN_xxx, - .rst_pin = AT91_PIN_xxx, - .irq_pin = ... not connected - .vcc_pin = ... always powered - + * Ethernet + */ +static struct at91_eth_data __initdata yl9200_eth_data = { + .phy_irq_pin = AT91_PIN_PB28, + .is_rmii = 1, }; -*/ -static struct at91_mmc_data __initdata yl_9200_mmc_data = { - .det_pin = AT91_PIN_PB9, /*THIS LOOKS CORRECT SHEET7*/ -/* .wp_pin = ... not connected SHEET7*/ - .slot_b = 0, - .wire4 = 1, +/* + * USB Host + */ +static struct at91_usbh_data __initdata yl9200_usbh_data = { + .ports = 1, /* PQFP version of AT91RM9200 */ }; -/* -------------------------------------------------------------------- - * Touch screen - * -------------------------------------------------------------------- */ -#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) -static int ads7843_pendown_state(void) -{ - return !at91_get_gpio_value(AT91_PIN_PB11); /* Touchscreen PENIRQ */ -} - -static void __init at91_init_device_ts(void) -{ -/*IMPORTANT NOTE THE SPI INTERFACE IS ALREADY CONFIGURED BY XXX_DEVICES.C -THAT IS TO SAY THAT MISO,MOSI,SPCK AND CS are already configured -we only need to enable the other datapins which are: -PB10/RK1 BUSY -*/ -/* Touchscreen BUSY signal , pin,use pullup ( TODO not currently used in the ADS7843/6.c driver)*/ -at91_set_gpio_input(AT91_PIN_PB10, 1); -} - -#else -static void __init at91_init_device_ts(void) {} -#endif - -static struct ads7846_platform_data ads_info = { - .model = 7843, - .x_min = 150, - .x_max = 3830, - .y_min = 190, - .y_max = 3830, - .vref_delay_usecs = 100, -/* for a 8" touch screen*/ - //.x_plate_ohms = 603, //= 450, S.Birtles TODO - //.y_plate_ohms = 332, //= 250, S.Birtles TODO -/*for a 10.4" touch screen*/ - //.x_plate_ohms =611, - //.y_plate_ohms =325, - - .x_plate_ohms = 576, - .y_plate_ohms = 366, - // - .pressure_max = 15000, /*generally nonsense on the 7843*/ - /*number of times to send query to chip in a given run 0 equals one time (do not set to 0!! ,there is a bug in ADS 7846 code)*/ - .debounce_max = 1, - .debounce_rep = 0, - .debounce_tol = (~0), - .get_pendown_state = ads7843_pendown_state, -}; +/* + * USB Device + */ +static struct at91_udc_data __initdata yl9200_udc_data = { + .pullup_pin = AT91_PIN_PC4, + .vbus_pin = AT91_PIN_PC5, + .pullup_active_low = 1, /* Active Low due to PNP transistor (pg 7) */ -/*static struct canbus_platform_data can_info = { - .model = 2510, }; -*/ - -static struct spi_board_info yl_9200_spi_devices[] = { -/*this sticks it at: - /sys/devices/platform/atmel_spi.0/spi0.0 - /sys/bus/platform/devices/ -Documentation/spi IIRC*/ -#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) - /*(this IS correct 04-NOV-2007)*/ - { - .modalias = "ads7846", /* because the driver is called ads7846*/ - .chip_select = 0, /*THIS MUST BE AN INDEX INTO AN ARRAY OF pins */ -/*this is ONLY TO BE USED if chipselect above is not used, it passes a pin directly for the chip select*/ - /*.controller_data =AT91_PIN_PA3 ,*/ - .max_speed_hz = 5000*26, /*(4700 * 26)-125000 * 26, (max sample rate @ 3V) * (cmd + data + overhead) */ - .bus_num = 0, - .platform_data = &ads_info, - .irq = AT91_PIN_PB11, - }, -#endif -/*we need to put our CAN driver data here!!*/ -/*THIS IS ALL DUMMY DATA*/ -/* { - .modalias = "mcp2510", //DUMMY for MCP2510 chip - .chip_select = 1,*/ /*THIS MUST BE AN INDEX INTO AN ARRAY OF pins */ - /*this is ONLY TO BE USED if chipselect above is not used, it passes a pin directly for the chip select */ - /* .controller_data =AT91_PIN_PA4 , - .max_speed_hz = 25000 * 26, - .bus_num = 0, - .platform_data = &can_info, - .irq = AT91_PIN_PC0, - }, - */ - //max SPI chip needs to go here +/* + * MMC + */ +static struct at91_mmc_data __initdata yl9200_mmc_data = { + .det_pin = AT91_PIN_PB9, + // .wp_pin = ... not connected + .wire4 = 1, }; -static struct mtd_partition __initdata yl_9200_nand_partition[] = { +/* + * NAND Flash + */ +static struct mtd_partition __initdata yl9200_nand_partition[] = { { .name = "AT91 NAND partition 1, boot", .offset = 0, @@ -242,442 +171,434 @@ static struct mtd_partition __initdata yl_9200_nand_partition[] = { .name = "AT91 NAND partition 5, ext-fs", .offset = 32 * SZ_1M, .size = 32 * SZ_1M - }, + } }; static struct mtd_partition * __init nand_partitions(int size, int *num_partitions) { - *num_partitions = ARRAY_SIZE(yl_9200_nand_partition); - return yl_9200_nand_partition; + *num_partitions = ARRAY_SIZE(yl9200_nand_partition); + return yl9200_nand_partition; } -static struct at91_nand_data __initdata yl_9200_nand_data = { - .ale= 6, - .cle= 7, - /*.det_pin = AT91_PIN_PCxx,*/ /*we don't have a det pin because NandFlash is fixed to board*/ - .rdy_pin = AT91_PIN_PC14, /*R/!B Sheet10*/ - .enable_pin = AT91_PIN_PC15, /*!CE Sheet10 */ +static struct at91_nand_data __initdata yl9200_nand_data = { + .ale = 6, + .cle = 7, + // .det_pin = ... not connected + .rdy_pin = AT91_PIN_PC14, /* R/!B (Sheet10) */ + .enable_pin = AT91_PIN_PC15, /* !CE (Sheet10) */ .partition_info = nand_partitions, }; - - /* -TODO S.Birtles -potentially a problem with the size above -physmap platform flash device: 00800000 at 10000000 -physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank -NOR chip too large to fit in mapping. Attempting to cope... - Intel/Sharp Extended Query Table at 0x0031 -Using buffer write method -cfi_cmdset_0001: Erase suspend on write enabled -Reducing visibility of 16384KiB chip to 8192KiB -*/ + * NOR Flash + */ +#define YL9200_FLASH_BASE AT91_CHIPSELECT_0 +#define YL9200_FLASH_SIZE 0x1000000 -static struct mtd_partition yl_9200_flash_partitions[] = { +static struct mtd_partition yl9200_flash_partitions[] = { + { + .name = "Bootloader", + .size = 0x00040000, + .offset = 0, + .mask_flags = MTD_WRITEABLE, /* force read-only */ + }, { - .name = "Bootloader", - .size = 0x00040000, - .offset = 0, - .mask_flags = MTD_WRITEABLE /* force read-only */ - },{ - .name = "Kernel", - .size = 0x001C0000, - .offset = 0x00040000, - },{ - .name = "Filesystem", - .size = MTDPART_SIZ_FULL, - .offset = 0x00200000 + .name = "Kernel", + .size = 0x001C0000, + .offset = 0x00040000, + }, + { + .name = "Filesystem", + .size = MTDPART_SIZ_FULL, + .offset = 0x00200000 } - }; -static struct physmap_flash_data yl_9200_flash_data = { - .width = 2, - .parts = yl_9200_flash_partitions, - .nr_parts = ARRAY_SIZE(yl_9200_flash_partitions), +static struct physmap_flash_data yl9200_flash_data = { + .width = 2, + .parts = yl9200_flash_partitions, + .nr_parts = ARRAY_SIZE(yl9200_flash_partitions), }; -static struct resource yl_9200_flash_resources[] = { -{ - .start = YL_9200_FLASH_BASE, - .end = YL_9200_FLASH_BASE + YL_9200_FLASH_SIZE - 1, - .flags = IORESOURCE_MEM, +static struct resource yl9200_flash_resources[] = { + { + .start = YL9200_FLASH_BASE, + .end = YL9200_FLASH_BASE + YL9200_FLASH_SIZE - 1, + .flags = IORESOURCE_MEM, } }; -static struct platform_device yl_9200_flash = { +static struct platform_device yl9200_flash = { .name = "physmap-flash", .id = 0, .dev = { - .platform_data = &yl_9200_flash_data, + .platform_data = &yl9200_flash_data, }, - .resource = yl_9200_flash_resources, - .num_resources = ARRAY_SIZE(yl_9200_flash_resources), + .resource = yl9200_flash_resources, + .num_resources = ARRAY_SIZE(yl9200_flash_resources), }; - -static struct gpio_led yl_9200_leds[] = { -/*D2 &D3 are passed directly in via at91_init_leds*/ - { - .name = "led4", /*D4*/ - .gpio = AT91_PIN_PB15, - .active_low = 1, - .default_trigger = "heartbeat", - /*.default_trigger = "timer",*/ - }, - { - .name = "led5", /*D5*/ - .gpio = AT91_PIN_PB8, - .active_low = 1, - .default_trigger = "heartbeat", - } -}; - -//static struct gpio_sounder yl_9200_sounder[] = {*/ -/*This is a simple speaker attached to a gpo line*/ - -// { -// .name = "Speaker", /*LS1*/ -// .gpio = AT91_PIN_PA22, -// .active_low = 0, -// .default_trigger = "heartbeat", - /*.default_trigger = "timer",*/ -// }, -//}; - - - -static struct i2c_board_info __initdata yl_9200_i2c_devices[] = { - { - /*TODO*/ - I2C_BOARD_INFO("CS4334", 0x00), +/* + * I2C (TWI) + */ +static struct i2c_board_info __initdata yl9200_i2c_devices[] = { + { /* EEPROM */ + I2C_BOARD_INFO("24c128", 0x50), } }; - - /* +/* * GPIO Buttons - */ +*/ #if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE) -static struct gpio_keys_button yl_9200_buttons[] = { +static struct gpio_keys_button yl9200_buttons[] = { { .gpio = AT91_PIN_PA24, - .code = BTN_2, + .code = BTN_2, .desc = "SW2", .active_low = 1, .wakeup = 1, }, { .gpio = AT91_PIN_PB1, - .code = BTN_3, + .code = BTN_3, .desc = "SW3", .active_low = 1, .wakeup = 1, }, { .gpio = AT91_PIN_PB2, - .code = BTN_4, + .code = BTN_4, .desc = "SW4", .active_low = 1, .wakeup = 1, }, { .gpio = AT91_PIN_PB6, - .code = BTN_5, + .code = BTN_5, .desc = "SW5", .active_low = 1, .wakeup = 1, - }, - + } }; -static struct gpio_keys_platform_data yl_9200_button_data = { - .buttons = yl_9200_buttons, - .nbuttons = ARRAY_SIZE(yl_9200_buttons), +static struct gpio_keys_platform_data yl9200_button_data = { + .buttons = yl9200_buttons, + .nbuttons = ARRAY_SIZE(yl9200_buttons), }; -static struct platform_device yl_9200_button_device = { +static struct platform_device yl9200_button_device = { .name = "gpio-keys", .id = -1, .num_resources = 0, .dev = { - .platform_data = &yl_9200_button_data, + .platform_data = &yl9200_button_data, } }; -static void __init yl_9200_add_device_buttons(void) +static void __init yl9200_add_device_buttons(void) { - //SW2 - at91_set_gpio_input(AT91_PIN_PA24, 0); + at91_set_gpio_input(AT91_PIN_PA24, 1); /* SW2 */ at91_set_deglitch(AT91_PIN_PA24, 1); - - //SW3 - at91_set_gpio_input(AT91_PIN_PB1, 0); + at91_set_gpio_input(AT91_PIN_PB1, 1); /* SW3 */ at91_set_deglitch(AT91_PIN_PB1, 1); - //SW4 - at91_set_gpio_input(AT91_PIN_PB2, 0); + at91_set_gpio_input(AT91_PIN_PB2, 1); /* SW4 */ at91_set_deglitch(AT91_PIN_PB2, 1); - - //SW5 - at91_set_gpio_input(AT91_PIN_PB6, 0); + at91_set_gpio_input(AT91_PIN_PB6, 1); /* SW5 */ at91_set_deglitch(AT91_PIN_PB6, 1); + /* Enable buttons (Sheet 5) */ + at91_set_gpio_output(AT91_PIN_PB7, 1); + + platform_device_register(&yl9200_button_device); +} +#else +static void __init yl9200_add_device_buttons(void) {} +#endif + +/* + * Touchscreen + */ +#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) +static int ads7843_pendown_state(void) +{ + return !at91_get_gpio_value(AT91_PIN_PB11); /* Touchscreen PENIRQ */ +} + +static struct ads7846_platform_data ads_info = { + .model = 7843, + .x_min = 150, + .x_max = 3830, + .y_min = 190, + .y_max = 3830, + .vref_delay_usecs = 100, + + /* For a 8" touch-screen */ + // .x_plate_ohms = 603, + // .y_plate_ohms = 332, + + /* For a 10.4" touch-screen */ + // .x_plate_ohms = 611, + // .y_plate_ohms = 325, + + .x_plate_ohms = 576, + .y_plate_ohms = 366, + + .pressure_max = 15000, /* generally nonsense on the 7843 */ + .debounce_max = 1, + .debounce_rep = 0, + .debounce_tol = (~0), + .get_pendown_state = ads7843_pendown_state, +}; - at91_set_gpio_output(AT91_PIN_PB7, 1); /* #TURN BUTTONS ON, SHEET 5 of schematics */ - platform_device_register(&yl_9200_button_device); +static void __init yl9200_add_device_ts(void) +{ + at91_set_gpio_input(AT91_PIN_PB11, 1); /* Touchscreen interrupt pin */ + at91_set_gpio_input(AT91_PIN_PB10, 1); /* Touchscreen BUSY signal - not used! */ } #else -static void __init yl_9200_add_device_buttons(void) {} +static void __init yl9200_add_device_ts(void) {} +#endif + +/* + * SPI devices + */ +static struct spi_board_info yl9200_spi_devices[] = { +#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE) + { /* Touchscreen */ + .modalias = "ads7846", + .chip_select = 0, + .max_speed_hz = 5000 * 26, + .platform_data = &ads_info, + .irq = AT91_PIN_PB11, + }, #endif + { /* CAN */ + .modalias = "mcp2510", + .chip_select = 1, + .max_speed_hz = 25000 * 26, + .irq = AT91_PIN_PC0, + } +}; +/* + * LCD / VGA + * + * EPSON S1D13806 FB (discontinued chip) + * EPSON S1D13506 FB + */ #if defined(CONFIG_FB_S1D135XX) || defined(CONFIG_FB_S1D13XXX_MODULE) #include