From 9f642b5c349a235d2f551267ddaaab2485a5e5c3 Mon Sep 17 00:00:00 2001 From: Dmitry Lifshitz Date: Mon, 28 Apr 2014 14:41:44 +0300 Subject: ARM: dts: sbc-t54: add support for sbc-t54 with cm-t54 Add support for CM-T54 CoM and SBC-T54 board: http://compulab.co.il/products/computer-on-modules/cm-t54/ http://compulab.co.il/products/sbcs/sbc-t54/ SBC-T54 is a single board computer based on OMAP5432 CPU. It is implemented with a CM-T54 CoM providing most of the functions, and SB-T54 carrier board providing connectors and several additional functions. Added basic support for: * PMIC * LED * MMC/SD * eMMC * USB * I2C1/4 * SB-T54 and CM-T54 EEPROMs * RTC Signed-off-by: Dmitry Lifshitz [tony@atomide.com: updated for Makefile sorting] Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/omap5-cm-t54.dts | 362 +++++++++++++++++++++++++++++++++++++ 1 file changed, 362 insertions(+) create mode 100644 arch/arm/boot/dts/omap5-cm-t54.dts (limited to 'arch/arm/boot/dts/omap5-cm-t54.dts') diff --git a/arch/arm/boot/dts/omap5-cm-t54.dts b/arch/arm/boot/dts/omap5-cm-t54.dts new file mode 100644 index 000000000000..e3018656ffd2 --- /dev/null +++ b/arch/arm/boot/dts/omap5-cm-t54.dts @@ -0,0 +1,362 @@ +/* + * Support for CompuLab CM-T54 + */ +/dts-v1/; + +#include "omap5.dtsi" +#include +#include + +/ { + model = "CompuLab CM-T54"; + compatible = "compulab,omap5-cm-t54", "ti,omap5"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x7F000000>; /* 2048 MB */ + }; + + vmmcsd_fixed: fixed-regulator-mmcsd { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + /* HS USB Host PHY on PORT 2 */ + hsusb2_phy: hsusb2_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>; /* gpio3_76 HUB_RESET */ + }; + + /* HS USB Host PHY on PORT 3 */ + hsusb3_phy: hsusb3_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; /* gpio3_83 ETH_RESET */ + }; + + leds { + compatible = "gpio-leds"; + led@1 { + label = "Heartbeat"; + gpios = <&gpio3 16 GPIO_ACTIVE_HIGH>; /* gpio3_80 ACT_LED */ + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + }; +}; + +&omap5_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = < + &led_gpio_pins + &usbhost_pins + >; + + led_gpio_pins: pinmux_led_gpio_pins { + pinctrl-single,pins = < + OMAP5_CORE_IOPAD(0x28b0, PIN_OUTPUT | MUX_MODE6) /* hsi2_caflag.gpio3_80 */ + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + OMAP5_CORE_IOPAD(0x29f2, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_scl */ + OMAP5_CORE_IOPAD(0x29f4, PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_pmic_sda */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP5_CORE_IOPAD(0x29e2, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_clk */ + OMAP5_CORE_IOPAD(0x29e4, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_cmd */ + OMAP5_CORE_IOPAD(0x29e6, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data2 */ + OMAP5_CORE_IOPAD(0x29e8, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data3 */ + OMAP5_CORE_IOPAD(0x29ea, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data0 */ + OMAP5_CORE_IOPAD(0x29ec, PIN_INPUT_PULLUP | MUX_MODE0) /* sdcard_data1 */ + >; + }; + + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + OMAP5_CORE_IOPAD(0x2840, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_clk */ + OMAP5_CORE_IOPAD(0x2842, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_cmd */ + OMAP5_CORE_IOPAD(0x2844, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data0 */ + OMAP5_CORE_IOPAD(0x2846, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data1 */ + OMAP5_CORE_IOPAD(0x2848, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data2 */ + OMAP5_CORE_IOPAD(0x284a, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data3 */ + OMAP5_CORE_IOPAD(0x284c, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data4 */ + OMAP5_CORE_IOPAD(0x284e, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data5 */ + OMAP5_CORE_IOPAD(0x2850, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data6 */ + OMAP5_CORE_IOPAD(0x2852, PIN_INPUT_PULLUP | MUX_MODE0) /* emmc_data7 */ + >; + }; + + usbhost_pins: pinmux_usbhost_pins { + pinctrl-single,pins = < + OMAP5_CORE_IOPAD(0x28c4, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_strobe */ + OMAP5_CORE_IOPAD(0x28c6, PIN_INPUT | MUX_MODE0) /* usbb2_hsic_data */ + + OMAP5_CORE_IOPAD(0x29dc, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_strobe */ + OMAP5_CORE_IOPAD(0x29de, PIN_INPUT | MUX_MODE0) /* usbb3_hsic_data */ + + OMAP5_CORE_IOPAD(0x28a8, PIN_OUTPUT | MUX_MODE6) /* hsi2_caready.gpio3_76 */ + OMAP5_CORE_IOPAD(0x28b6, PIN_OUTPUT | MUX_MODE6) /* hsi2_acdata.gpio3_83 */ + >; + }; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <&ldo9_reg>; + bus-width = <4>; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <8>; + ti,non-removable; +}; + +&mmc4 { + status = "disabled"; +}; + +&mmc5 { + status = "disabled"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + + clock-frequency = <400000>; + + at24@50 { + compatible = "at24,24c02"; + pagesize = <16>; + reg = <0x50>; + }; + + palmas: palmas@48 { + compatible = "ti,palmas"; + interrupts = ; /* IRQ_SYS_1N */ + interrupt-parent = <&gic>; + reg = <0x48>; + interrupt-controller; + #interrupt-cells = <2>; + ti,system-power-controller; + + extcon_usb3: palmas_usb { + compatible = "ti,palmas-usb-vid"; + ti,enable-vbus-detection; + ti,enable-id-detection; + ti,wakeup; + }; + + rtc { + compatible = "ti,palmas-rtc"; + interrupt-parent = <&palmas>; + interrupts = <8 IRQ_TYPE_NONE>; + }; + + palmas_pmic { + compatible = "ti,palmas-pmic"; + interrupt-parent = <&palmas>; + interrupts = <14 IRQ_TYPE_NONE>; + interrupt-name = "short-irq"; + + ti,ldo6-vibrator; + + regulators { + smps123_reg: smps123 { + /* VDD_OPP_MPU */ + regulator-name = "smps123"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + smps45_reg: smps45 { + /* VDD_OPP_MM */ + regulator-name = "smps45"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1310000>; + regulator-always-on; + regulator-boot-on; + }; + + smps6_reg: smps6 { + /* VDD_DDR3 - over VDD_SMPS6 */ + regulator-name = "smps6"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + smps7_reg: smps7 { + /* VDDS_1v8_OMAP over VDDS_1v8_MAIN */ + regulator-name = "smps7"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + smps8_reg: smps8 { + /* VDD_OPP_CORE */ + regulator-name = "smps8"; + regulator-min-microvolt = < 600000>; + regulator-max-microvolt = <1310000>; + regulator-always-on; + regulator-boot-on; + }; + + smps9_reg: smps9 { + /* VDDA_2v1_AUD over VDD_2v1 */ + regulator-name = "smps9"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + ti,smps-range = <0x80>; + regulator-always-on; + regulator-boot-on; + }; + + smps10_out2_reg: smps10_out2 { + /* VBUS_5V_OTG */ + regulator-name = "smps10_out2"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + regulator-boot-on; + }; + + smps10_out1_reg: smps10_out1 { + /* VBUS_5V_OTG */ + regulator-name = "smps10_out1"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + ldo1_reg: ldo1 { + /* VDDAPHY_CAM: vdda_csiport */ + regulator-name = "ldo1"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1800000>; + }; + + ldo2_reg: ldo2 { + /* VDD_3V3_WLAN */ + regulator-name = "ldo2"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + }; + + ldo3_reg: ldo3 { + /* VCC_1V5_AUD */ + regulator-name = "ldo3"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo4_reg: ldo4 { + /* VDDAPHY_DISP: vdda_dsiport/hdmi */ + regulator-name = "ldo4"; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1800000>; + }; + + ldo5_reg: ldo5 { + /* VDDA_1V8_PHY: usb/sata/hdmi.. */ + regulator-name = "ldo5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo6_reg: ldo6 { + /* VDDS_1V2_WKUP: hsic/ldo_emu_wkup */ + regulator-name = "ldo6"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + }; + + ldo7_reg: ldo7 { + /* VDD_VPP: vpp1 */ + regulator-name = "ldo7"; + regulator-min-microvolt = <2000000>; + regulator-max-microvolt = <2000000>; + /* Only for efuse reprograming! */ + status = "disabled"; + }; + + ldo8_reg: ldo8 { + /* VDD_3v0: Does not go anywhere */ + regulator-name = "ldo8"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + /* Unused */ + status = "disabled"; + }; + + ldo9_reg: ldo9 { + /* VCC_DV_SDIO: vdds_sdcard */ + regulator-name = "ldo9"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + }; + + ldoln_reg: ldoln { + /* VDDA_1v8_REF: vdds_osc/mm_l4per.. */ + regulator-name = "ldoln"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + ldousb_reg: ldousb { + /* VDDA_3V_USB: VDDA_USBHS33 */ + regulator-name = "ldousb"; + regulator-min-microvolt = <3250000>; + regulator-max-microvolt = <3250000>; + regulator-always-on; + regulator-boot-on; + }; + + regen3_reg: regen3 { + /* REGEN3 controls LDO9 supply to card */ + regulator-name = "regen3"; + regulator-always-on; + regulator-boot-on; + }; + }; + }; + }; +}; + +&usbhshost { + port2-mode = "ehci-hsic"; + port3-mode = "ehci-hsic"; +}; + +&usbhsehci { + phys = <0 &hsusb2_phy &hsusb3_phy>; +}; + +&cpu0 { + cpu0-supply = <&smps123_reg>; +}; -- cgit v1.2.1