From f4c737d6194f509733641017b50548abc01f4b0d Mon Sep 17 00:00:00 2001 From: Jianjun Wang Date: Fri, 28 Jun 2019 15:34:24 +0800 Subject: dt-bindings: PCI: Add support for MT7629 MT7629 is an ARM based platform SoC integrating the same PCIe IP as MT7622, add a binding for it. Signed-off-by: Jianjun Wang Signed-off-by: Lorenzo Pieralisi Reviewed-by: Rob Herring Acked-by: Ryder Lee --- Documentation/devicetree/bindings/pci/mediatek-pcie.txt | 1 + 1 file changed, 1 insertion(+) (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt index 92437a366e5f..7468d666763a 100644 --- a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt @@ -6,6 +6,7 @@ Required properties: "mediatek,mt2712-pcie" "mediatek,mt7622-pcie" "mediatek,mt7623-pcie" + "mediatek,mt7629-pcie" - device_type: Must be "pci" - reg: Base addresses and lengths of the PCIe subsys and root ports. - reg-names: Names of the above areas to use during resource lookup. -- cgit v1.2.1 From f4e84a5d9db7dfea96832157bc461177e87a47dd Mon Sep 17 00:00:00 2001 From: Vidya Sagar Date: Tue, 13 Aug 2019 17:06:21 +0530 Subject: dt-bindings: PCI: designware: Add binding for CDM register check Add support to enable CDM (Configuration Dependent Module) registers check for any data corruption. CDM registers include standard PCIe configuration space registers, Port Logic registers and iATU and DMA registers. Refer Section S.4 of Synopsys DesignWare Cores PCI Express Controller Databook Version 4.90a. Signed-off-by: Vidya Sagar Signed-off-by: Lorenzo Pieralisi Reviewed-by: Thierry Reding Reviewed-by: Rob Herring --- Documentation/devicetree/bindings/pci/designware-pcie.txt | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index 5561a1c060d0..3fba04da6a59 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -34,6 +34,11 @@ Optional properties: - clock-names: Must include the following entries: - "pcie" - "pcie_bus" +- snps,enable-cdm-check: This is a boolean property and if present enables + automatic checking of CDM (Configuration Dependent Module) registers + for data corruption. CDM registers include standard PCIe configuration + space registers, Port Logic registers, DMA and iATU (internal Address + Translation Unit) registers. RC mode: - num-viewport: number of view ports configured in hardware. If a platform does not specify it, the driver assumes 2. -- cgit v1.2.1 From 7b31a72e7195aebd620d504f28b97ad8398e95ec Mon Sep 17 00:00:00 2001 From: Vidya Sagar Date: Tue, 13 Aug 2019 17:06:23 +0530 Subject: dt-bindings: Add PCIe supports-clkreq property Some host controllers need to know the existence of clkreq signal routing to downstream devices to be able to advertise low power features like ASPM L1 substates. Without clkreq signal routing being present, enabling ASPM L1 substates might lead to downstream devices being disconnected from the bus. Hence a new device tree property 'supports-clkreq' is added to make such host controllers aware of clkreq signal routing to downstream devices. Signed-off-by: Vidya Sagar Signed-off-by: Lorenzo Pieralisi Reviewed-by: Rob Herring Reviewed-by: Thierry Reding --- Documentation/devicetree/bindings/pci/pci.txt | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/pci/pci.txt b/Documentation/devicetree/bindings/pci/pci.txt index 2a5d91024059..29bcbd88f457 100644 --- a/Documentation/devicetree/bindings/pci/pci.txt +++ b/Documentation/devicetree/bindings/pci/pci.txt @@ -27,6 +27,11 @@ driver implementation may support the following properties: - reset-gpios: If present this property specifies PERST# GPIO. Host drivers can parse the GPIO and apply fundamental reset to endpoints. +- supports-clkreq: + If present this property specifies that CLKREQ signal routing exists from + root port to downstream device and host bridge drivers can do programming + which depends on CLKREQ signal existence. For example, programming root port + not to advertise ASPM L1 Sub-States support if there is no CLKREQ signal. PCI-PCI Bridge properties ------------------------- -- cgit v1.2.1 From 42c253ecaa53c0a2fee431018dd18d2fa797580f Mon Sep 17 00:00:00 2001 From: Vidya Sagar Date: Tue, 13 Aug 2019 17:06:24 +0530 Subject: dt-bindings: PCI: tegra: Add device tree support for Tegra194 Add support for Tegra194 PCIe controllers. These controllers are based on Synopsys DesignWare core IP. Signed-off-by: Vidya Sagar Signed-off-by: Lorenzo Pieralisi Reviewed-by: Rob Herring Acked-by: Thierry Reding --- .../bindings/pci/nvidia,tegra194-pcie.txt | 155 +++++++++++++++++++++ 1 file changed, 155 insertions(+) create mode 100644 Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt new file mode 100644 index 000000000000..674e5adb2895 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt @@ -0,0 +1,155 @@ +NVIDIA Tegra PCIe controller (Synopsys DesignWare Core based) + +This PCIe host controller is based on the Synopsis Designware PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: For Tegra19x, must contain "nvidia,tegra194-pcie". +- device_type: Must be "pci" +- power-domains: A phandle to the node that controls power to the respective + PCIe controller and a specifier name for the PCIe controller. Following are + the specifiers for the different PCIe controllers + TEGRA194_POWER_DOMAIN_PCIEX8B: C0 + TEGRA194_POWER_DOMAIN_PCIEX1A: C1 + TEGRA194_POWER_DOMAIN_PCIEX1A: C2 + TEGRA194_POWER_DOMAIN_PCIEX1A: C3 + TEGRA194_POWER_DOMAIN_PCIEX4A: C4 + TEGRA194_POWER_DOMAIN_PCIEX8A: C5 + these specifiers are defined in + "include/dt-bindings/power/tegra194-powergate.h" file. +- reg: A list of physical base address and length pairs for each set of + controller registers. Must contain an entry for each entry in the reg-names + property. +- reg-names: Must include the following entries: + "appl": Controller's application logic registers + "config": As per the definition in designware-pcie.txt + "atu_dma": iATU and DMA registers. This is where the iATU (internal Address + Translation Unit) registers of the PCIe core are made available + for SW access. + "dbi": The aperture where root port's own configuration registers are + available +- interrupts: A list of interrupt outputs of the controller. Must contain an + entry for each entry in the interrupt-names property. +- interrupt-names: Must include the following entries: + "intr": The Tegra interrupt that is asserted for controller interrupts + "msi": The Tegra interrupt that is asserted when an MSI is received +- bus-range: Range of bus numbers associated with this controller +- #address-cells: Address representation for root ports (must be 3) + - cell 0 specifies the bus and device numbers of the root port: + [23:16]: bus number + [15:11]: device number + - cell 1 denotes the upper 32 address bits and should be 0 + - cell 2 contains the lower 32 address bits and is used to translate to the + CPU address space +- #size-cells: Size representation for root ports (must be 2) +- ranges: Describes the translation of addresses for root ports and standard + PCI regions. The entries must be 7 cells each, where the first three cells + correspond to the address as described for the #address-cells property + above, the fourth and fifth cells are for the physical CPU address to + translate to and the sixth and seventh cells are as described for the + #size-cells property above. + - Entries setup the mapping for the standard I/O, memory and + prefetchable PCI regions. The first cell determines the type of region + that is setup: + - 0x81000000: I/O memory region + - 0x82000000: non-prefetchable memory region + - 0xc2000000: prefetchable memory region + Please refer to the standard PCI bus binding document for a more detailed + explanation. +- #interrupt-cells: Size representation for interrupts (must be 1) +- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties + Please refer to the standard PCI bus binding document for a more detailed + explanation. +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - core +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - apb + - core +- phys: Must contain a phandle to P2U PHY for each entry in phy-names. +- phy-names: Must include an entry for each active lane. + "p2u-N": where N ranges from 0 to one less than the total number of lanes +- nvidia,bpmp: Must contain a pair of phandle to BPMP controller node followed + by controller-id. Following are the controller ids for each controller. + 0: C0 + 1: C1 + 2: C2 + 3: C3 + 4: C4 + 5: C5 +- vddio-pex-ctl-supply: Regulator supply for PCIe side band signals + +Optional properties: +- supports-clkreq: Refer to Documentation/devicetree/bindings/pci/pci.txt +- nvidia,update-fc-fixup: This is a boolean property and needs to be present to + improve performance when a platform is designed in such a way that it + satisfies at least one of the following conditions thereby enabling root + port to exchange optimum number of FC (Flow Control) credits with + downstream devices + 1. If C0/C4/C5 run at x1/x2 link widths (irrespective of speed and MPS) + 2. If C0/C1/C2/C3/C4/C5 operate at their respective max link widths and + a) speed is Gen-2 and MPS is 256B + b) speed is >= Gen-3 with any MPS +- nvidia,aspm-cmrt-us: Common Mode Restore Time for proper operation of ASPM + to be specified in microseconds +- nvidia,aspm-pwr-on-t-us: Power On time for proper operation of ASPM to be + specified in microseconds +- nvidia,aspm-l0s-entrance-latency-us: ASPM L0s entrance latency to be + specified in microseconds + +Examples: +========= + +Tegra194: +-------- + + pcie@14180000 { + compatible = "nvidia,tegra194-pcie", "snps,dw-pcie"; + power-domains = <&bpmp TEGRA194_POWER_DOMAIN_PCIEX8B>; + reg = <0x00 0x14180000 0x0 0x00020000 /* appl registers (128K) */ + 0x00 0x38000000 0x0 0x00040000 /* configuration space (256K) */ + 0x00 0x38040000 0x0 0x00040000>; /* iATU_DMA reg space (256K) */ + reg-names = "appl", "config", "atu_dma"; + + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + num-lanes = <8>; + linux,pci-domain = <0>; + + clocks = <&bpmp TEGRA194_CLK_PEX0_CORE_0>; + clock-names = "core"; + + resets = <&bpmp TEGRA194_RESET_PEX0_CORE_0_APB>, + <&bpmp TEGRA194_RESET_PEX0_CORE_0>; + reset-names = "apb", "core"; + + interrupts = , /* controller interrupt */ + ; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; + + nvidia,bpmp = <&bpmp 0>; + + supports-clkreq; + nvidia,aspm-cmrt-us = <60>; + nvidia,aspm-pwr-on-t-us = <20>; + nvidia,aspm-l0s-entrance-latency-us = <3>; + + bus-range = <0x0 0xff>; + ranges = <0x81000000 0x0 0x38100000 0x0 0x38100000 0x0 0x00100000 /* downstream I/O (1MB) */ + 0x82000000 0x0 0x38200000 0x0 0x38200000 0x0 0x01E00000 /* non-prefetchable memory (30MB) */ + 0xc2000000 0x18 0x00000000 0x18 0x00000000 0x4 0x00000000>; /* prefetchable memory (16GB) */ + + vddio-pex-ctl-supply = <&vdd_1v8ao>; + + phys = <&p2u_hsio_2>, <&p2u_hsio_3>, <&p2u_hsio_4>, + <&p2u_hsio_5>; + phy-names = "p2u-0", "p2u-1", "p2u-2", "p2u-3"; + }; -- cgit v1.2.1 From 813c6fbcb7756e96f96c5931d8830970ff50e3b0 Mon Sep 17 00:00:00 2001 From: Vidya Sagar Date: Tue, 13 Aug 2019 17:06:25 +0530 Subject: dt-bindings: PHY: P2U: Add Tegra194 P2U block Add support for Tegra194 P2U (PIPE to UPHY) module block which is a glue module instantiated once for each PCIe lane between Synopsys DesignWare core based PCIe IP and Universal PHY block. Signed-off-by: Vidya Sagar Signed-off-by: Lorenzo Pieralisi Reviewed-by: Rob Herring Acked-by: Thierry Reding Acked-by: Kishon Vijay Abraham I --- .../devicetree/bindings/phy/phy-tegra194-p2u.txt | 28 ++++++++++++++++++++++ 1 file changed, 28 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/phy-tegra194-p2u.txt (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/phy/phy-tegra194-p2u.txt b/Documentation/devicetree/bindings/phy/phy-tegra194-p2u.txt new file mode 100644 index 000000000000..d23ff90baad5 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-tegra194-p2u.txt @@ -0,0 +1,28 @@ +NVIDIA Tegra194 P2U binding + +Tegra194 has two PHY bricks namely HSIO (High Speed IO) and NVHS (NVIDIA High +Speed) each interfacing with 12 and 8 P2U instances respectively. +A P2U instance is a glue logic between Synopsys DesignWare Core PCIe IP's PIPE +interface and PHY of HSIO/NVHS bricks. Each P2U instance represents one PCIe +lane. + +Required properties: +- compatible: For Tegra19x, must contain "nvidia,tegra194-p2u". +- reg: Should be the physical address space and length of respective each P2U + instance. +- reg-names: Must include the entry "ctl". + +Required properties for PHY port node: +- #phy-cells: Defined by generic PHY bindings. Must be 0. + +Refer to phy/phy-bindings.txt for the generic PHY binding properties. + +Example: + +p2u_hsio_0: phy@3e10000 { + compatible = "nvidia,tegra194-p2u"; + reg = <0x03e10000 0x10000>; + reg-names = "ctl"; + + #phy-cells = <0>; +}; -- cgit v1.2.1 From ee4ea764ea03253016034603cab352c0798ce173 Mon Sep 17 00:00:00 2001 From: Hou Zhiqiang Date: Tue, 20 Aug 2019 07:28:43 +0000 Subject: dt-bindings: PCI: designware: Remove the num-lanes from Required properties The num-lanes is not a mandatory property, e.g. on FSL Layerscape SoCs, the PCIe link training is completed automatically based on the selected SerDes protocol, it does not need the num-lanes to set-up the link width. Currently it is both a Required and Optional property, let's remove it from the Required properties. Signed-off-by: Hou Zhiqiang Signed-off-by: Lorenzo Pieralisi Reviewed-by: Andrew Murray --- Documentation/devicetree/bindings/pci/designware-pcie.txt | 1 - 1 file changed, 1 deletion(-) (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt index 5561a1c060d0..bd880df39a79 100644 --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -11,7 +11,6 @@ Required properties: the ATU address space. (The old way of getting the configuration address space from "ranges" is deprecated and should be avoided.) -- num-lanes: number of lanes to use RC mode: - #address-cells: set to <3> - #size-cells: set to <2> -- cgit v1.2.1 From d1bbf38aaf882240cccca414e5a48db42e105da7 Mon Sep 17 00:00:00 2001 From: Bjorn Helgaas Date: Tue, 30 Jul 2019 08:04:00 -0500 Subject: PCI: Fix typos and whitespace errors Fix typos in drivers/pci. Comment and whitespace changes only. Link: https://lore.kernel.org/r/20190819115306.27338-1-kw@linux.com Signed-off-by: Krzysztof Wilczynski Signed-off-by: Bjorn Helgaas Reviewed-by: Rob Herring Acked-by: Thomas Petazzoni # armada8k --- Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt | 2 +- Documentation/devicetree/bindings/pci/pci-armada8k.txt | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt index a7f5f5afa0e6..de4b2baf91e8 100644 --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -50,7 +50,7 @@ Additional required properties for imx7d-pcie and imx8mq-pcie: - power-domains: Must be set to a phandle pointing to PCIE_PHY power domain - resets: Must contain phandles to PCIe-related reset lines exposed by SRC IP block -- reset-names: Must contain the following entires: +- reset-names: Must contain the following entries: - "pciephy" - "apps" - "turnoff" diff --git a/Documentation/devicetree/bindings/pci/pci-armada8k.txt b/Documentation/devicetree/bindings/pci/pci-armada8k.txt index 9e3fc15e1af8..1aaa09254001 100644 --- a/Documentation/devicetree/bindings/pci/pci-armada8k.txt +++ b/Documentation/devicetree/bindings/pci/pci-armada8k.txt @@ -11,7 +11,7 @@ Required properties: - reg-names: - "ctrl" for the control register region - "config" for the config space region -- interrupts: Interrupt specifier for the PCIe controler +- interrupts: Interrupt specifier for the PCIe controller - clocks: reference to the PCIe controller clocks - clock-names: mandatory if there is a second clock, in this case the name must be "core" for the first clock and "reg" for the second -- cgit v1.2.1 From 151481ef5e360af4ca68835943a036339d3c7826 Mon Sep 17 00:00:00 2001 From: Vidya Sagar Date: Thu, 5 Sep 2019 16:15:48 +0530 Subject: dt-bindings: PCI: tegra: Add sideband pins configuration entries Add optional bindings "pinctrl-names" and "pinctrl-0" to describe pin configuration information of a particular PCIe controller. Signed-off-by: Vidya Sagar Signed-off-by: Lorenzo Pieralisi Reviewed-by: Andrew Murray Reviewed-by: Rob Herring Acked-by: Thierry Reding --- Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt index 674e5adb2895..0ac1b867ac24 100644 --- a/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt @@ -83,6 +83,11 @@ Required properties: - vddio-pex-ctl-supply: Regulator supply for PCIe side band signals Optional properties: +- pinctrl-names: A list of pinctrl state names. + It is mandatory for C5 controller and optional for other controllers. + - "default": Configures PCIe I/O for proper operation. +- pinctrl-0: phandle for the 'default' state of pin configuration. + It is mandatory for C5 controller and optional for other controllers. - supports-clkreq: Refer to Documentation/devicetree/bindings/pci/pci.txt - nvidia,update-fc-fixup: This is a boolean property and needs to be present to improve performance when a platform is designed in such a way that it @@ -120,6 +125,9 @@ Tegra194: num-lanes = <8>; linux,pci-domain = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pex_rst_c5_out_state>, <&clkreq_c5_bi_dir_state>; + clocks = <&bpmp TEGRA194_CLK_PEX0_CORE_0>; clock-names = "core"; -- cgit v1.2.1 From 7ed106d8fdfa4e6cbf9226f49ce921a681c9f240 Mon Sep 17 00:00:00 2001 From: Vidya Sagar Date: Thu, 5 Sep 2019 16:15:49 +0530 Subject: dt-bindings: PCI: tegra: Add PCIe slot supplies regulator entries Add optional bindings "vpcie3v3-supply" and "vpcie12v-supply" to describe regulators of a PCIe slot's supplies 3.3V and 12V provided the platform is designed to have regulator controlled slot supplies. Signed-off-by: Vidya Sagar Signed-off-by: Lorenzo Pieralisi Reviewed-by: Andrew Murray Reviewed-by: Rob Herring Acked-by: Thierry Reding --- Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt index 0ac1b867ac24..b739f92da58e 100644 --- a/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt @@ -104,6 +104,12 @@ Optional properties: specified in microseconds - nvidia,aspm-l0s-entrance-latency-us: ASPM L0s entrance latency to be specified in microseconds +- vpcie3v3-supply: A phandle to the regulator node that supplies 3.3V to the slot + if the platform has one such slot. (Ex:- x16 slot owned by C5 controller + in p2972-0000 platform). +- vpcie12v-supply: A phandle to the regulator node that supplies 12V to the slot + if the platform has one such slot. (Ex:- x16 slot owned by C5 controller + in p2972-0000 platform). Examples: ========= @@ -156,6 +162,8 @@ Tegra194: 0xc2000000 0x18 0x00000000 0x18 0x00000000 0x4 0x00000000>; /* prefetchable memory (16GB) */ vddio-pex-ctl-supply = <&vdd_1v8ao>; + vpcie3v3-supply = <&vdd_3v3_pcie>; + vpcie12v-supply = <&vdd_12v_pcie>; phys = <&p2u_hsio_2>, <&p2u_hsio_3>, <&p2u_hsio_4>, <&p2u_hsio_5>; -- cgit v1.2.1 From ed4381da34d4765626aefc9b9ef084cd8e6bb749 Mon Sep 17 00:00:00 2001 From: Jonathan Chocron Date: Thu, 12 Sep 2019 16:02:36 +0300 Subject: dt-bindings: PCI: Add Amazon's Annapurna Labs PCIe host bridge binding Document Amazon's Annapurna Labs PCIe host bridge. Signed-off-by: Jonathan Chocron Signed-off-by: Lorenzo Pieralisi Reviewed-by: Andrew Murray Reviewed-by: Rob Herring --- Documentation/devicetree/bindings/pci/pcie-al.txt | 46 +++++++++++++++++++++++ 1 file changed, 46 insertions(+) create mode 100644 Documentation/devicetree/bindings/pci/pcie-al.txt (limited to 'Documentation/devicetree') diff --git a/Documentation/devicetree/bindings/pci/pcie-al.txt b/Documentation/devicetree/bindings/pci/pcie-al.txt new file mode 100644 index 000000000000..557a5089229d --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pcie-al.txt @@ -0,0 +1,46 @@ +* Amazon Annapurna Labs PCIe host bridge + +Amazon's Annapurna Labs PCIe Host Controller is based on the Synopsys DesignWare +PCI core. It inherits common properties defined in +Documentation/devicetree/bindings/pci/designware-pcie.txt. + +Properties of the host controller node that differ from it are: + +- compatible: + Usage: required + Value type: + Definition: Value should contain + - "amazon,al-alpine-v2-pcie" for alpine_v2 + - "amazon,al-alpine-v3-pcie" for alpine_v3 + +- reg: + Usage: required + Value type: + Definition: Register ranges as listed in the reg-names property + +- reg-names: + Usage: required + Value type: + Definition: Must include the following entries + - "config" PCIe ECAM space + - "controller" AL proprietary registers + - "dbi" Designware PCIe registers + +Example: + + pcie-external0: pcie@fb600000 { + compatible = "amazon,al-alpine-v3-pcie"; + reg = <0x0 0xfb600000 0x0 0x00100000 + 0x0 0xfd800000 0x0 0x00010000 + 0x0 0xfd810000 0x0 0x00001000>; + reg-names = "config", "controller", "dbi"; + bus-range = <0 255>; + device_type = "pci"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupts = ; + interrupt-map-mask = <0x00 0 0 7>; + interrupt-map = <0x0000 0 0 1 &gic GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; /* INTa */ + ranges = <0x02000000 0x0 0xc0010000 0x0 0xc0010000 0x0 0x07ff0000>; + }; -- cgit v1.2.1