From 7111ebc97ed53a32314011c85a6f235f0dab8ae8 Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Tue, 14 Dec 2010 13:24:55 -0800 Subject: xhci: Resume bus on any port status change. The original code that resumed the USB bus on a port status change would only do so when there was a device connected to the port. If a device was just disconnected, the event would be queued for khubd, but khubd wouldn't run. That would leave the connect status change (CSC) bit set. If a USB device was plugged into that same port, the xHCI host controller would set the current connect status (CCS) bit. But since the CSC bit was already set, it would not generate an interrupt for a port status change event. That would mean the user could "Safely Remove" a device, have the bus suspend, disconnect the device, re-plug it in, and then the device would never be enumerated. Plugging in a different device on another port would cause the bus to resume, and khubd would notice the re-connected device. Running lsusb would also resume the bus, leading users to report the problem "went away" when using diagnostic tools. The solution is to resume the bus when a port status change event is received, regardless of the port status. Thank you very much to Maddog for helping me track down this Heisenbug. This patch should be queued for the 2.6.37 stable tree. Signed-off-by: Sarah Sharp Reported-by: Jon 'maddog' Hall Tested-by: Andiry Xu Cc: stable@kernel.org --- drivers/usb/host/xhci-ring.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index df558f6f84e3..62c70c230e83 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -1188,7 +1188,7 @@ static void handle_port_status(struct xhci_hcd *xhci, addr = &xhci->op_regs->port_status_base + NUM_PORT_REGS * (port_id - 1); temp = xhci_readl(xhci, addr); - if ((temp & PORT_CONNECT) && (hcd->state == HC_STATE_SUSPENDED)) { + if (hcd->state == HC_STATE_SUSPENDED) { xhci_dbg(xhci, "resume root hub\n"); usb_hcd_resume_root_hub(hcd); } -- cgit v1.2.1 From 0029227f1bc30b6c809ae751f9e7af6cef900997 Mon Sep 17 00:00:00 2001 From: Andiry Xu Date: Mon, 27 Dec 2010 17:39:02 +0800 Subject: xHCI: synchronize irq in xhci_suspend() Synchronize the interrupts instead of free them in xhci_suspend(). This will prevent a double free when the host is suspended and then the card removed. Set the flag hcd->msix_enabled when using MSI-X, and check the flag in suspend_common(). MSI-X synchronization will be handled by xhci_suspend(), and MSI/INTx will be synchronized in suspend_common(). This patch should be queued for the 2.6.37 stable tree. Reported-by: Matthew Garrett Signed-off-by: Andiry Xu Signed-off-by: Sarah Sharp Cc: stable@kernel.org --- drivers/usb/core/hcd-pci.c | 7 ++++++- drivers/usb/host/xhci.c | 46 +++++++++++++++------------------------------- include/linux/usb/hcd.h | 1 + 3 files changed, 22 insertions(+), 32 deletions(-) diff --git a/drivers/usb/core/hcd-pci.c b/drivers/usb/core/hcd-pci.c index b55d46070a25..f71e8e307e0f 100644 --- a/drivers/usb/core/hcd-pci.c +++ b/drivers/usb/core/hcd-pci.c @@ -405,7 +405,12 @@ static int suspend_common(struct device *dev, bool do_wakeup) return retval; } - synchronize_irq(pci_dev->irq); + /* If MSI-X is enabled, the driver will have synchronized all vectors + * in pci_suspend(). If MSI or legacy PCI is enabled, that will be + * synchronized here. + */ + if (!hcd->msix_enabled) + synchronize_irq(pci_dev->irq); /* Downstream ports from this root hub should already be quiesced, so * there will be no DMA activity. Now we can shut down the upstream diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index 45e4a3108cc3..d48edfa5043a 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -226,7 +226,8 @@ static int xhci_setup_msi(struct xhci_hcd *xhci) static int xhci_setup_msix(struct xhci_hcd *xhci) { int i, ret = 0; - struct pci_dev *pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller); + struct usb_hcd *hcd = xhci_to_hcd(xhci); + struct pci_dev *pdev = to_pci_dev(hcd->self.controller); /* * calculate number of msi-x vectors supported. @@ -265,6 +266,7 @@ static int xhci_setup_msix(struct xhci_hcd *xhci) goto disable_msix; } + hcd->msix_enabled = 1; return ret; disable_msix: @@ -280,7 +282,8 @@ free_entries: /* Free any IRQs and disable MSI-X */ static void xhci_cleanup_msix(struct xhci_hcd *xhci) { - struct pci_dev *pdev = to_pci_dev(xhci_to_hcd(xhci)->self.controller); + struct usb_hcd *hcd = xhci_to_hcd(xhci); + struct pci_dev *pdev = to_pci_dev(hcd->self.controller); xhci_free_irq(xhci); @@ -292,6 +295,7 @@ static void xhci_cleanup_msix(struct xhci_hcd *xhci) pci_disable_msi(pdev); } + hcd->msix_enabled = 0; return; } @@ -647,6 +651,7 @@ int xhci_suspend(struct xhci_hcd *xhci) int rc = 0; struct usb_hcd *hcd = xhci_to_hcd(xhci); u32 command; + int i; spin_lock_irq(&xhci->lock); clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags); @@ -677,10 +682,15 @@ int xhci_suspend(struct xhci_hcd *xhci) spin_unlock_irq(&xhci->lock); return -ETIMEDOUT; } - /* step 5: remove core well power */ - xhci_cleanup_msix(xhci); spin_unlock_irq(&xhci->lock); + /* step 5: remove core well power */ + /* synchronize irq when using MSI-X */ + if (xhci->msix_entries) { + for (i = 0; i < xhci->msix_count; i++) + synchronize_irq(xhci->msix_entries[i].vector); + } + return rc; } @@ -694,7 +704,6 @@ int xhci_resume(struct xhci_hcd *xhci, bool hibernated) { u32 command, temp = 0; struct usb_hcd *hcd = xhci_to_hcd(xhci); - struct pci_dev *pdev = to_pci_dev(hcd->self.controller); int old_state, retval; old_state = hcd->state; @@ -729,9 +738,8 @@ int xhci_resume(struct xhci_hcd *xhci, bool hibernated) xhci_dbg(xhci, "Stop HCD\n"); xhci_halt(xhci); xhci_reset(xhci); - if (hibernated) - xhci_cleanup_msix(xhci); spin_unlock_irq(&xhci->lock); + xhci_cleanup_msix(xhci); #ifdef CONFIG_USB_XHCI_HCD_DEBUGGING /* Tell the event ring poll function not to reschedule */ @@ -765,30 +773,6 @@ int xhci_resume(struct xhci_hcd *xhci, bool hibernated) return retval; } - spin_unlock_irq(&xhci->lock); - /* Re-setup MSI-X */ - if (hcd->irq) - free_irq(hcd->irq, hcd); - hcd->irq = -1; - - retval = xhci_setup_msix(xhci); - if (retval) - /* fall back to msi*/ - retval = xhci_setup_msi(xhci); - - if (retval) { - /* fall back to legacy interrupt*/ - retval = request_irq(pdev->irq, &usb_hcd_irq, IRQF_SHARED, - hcd->irq_descr, hcd); - if (retval) { - xhci_err(xhci, "request interrupt %d failed\n", - pdev->irq); - return retval; - } - hcd->irq = pdev->irq; - } - - spin_lock_irq(&xhci->lock); /* step 4: set Run/Stop bit */ command = xhci_readl(xhci, &xhci->op_regs->command); command |= CMD_RUN; diff --git a/include/linux/usb/hcd.h b/include/linux/usb/hcd.h index dd6ee49a0844..a854fe89484e 100644 --- a/include/linux/usb/hcd.h +++ b/include/linux/usb/hcd.h @@ -112,6 +112,7 @@ struct usb_hcd { /* Flags that get set only during HCD registration or removal. */ unsigned rh_registered:1;/* is root hub registered? */ unsigned rh_pollable:1; /* may we poll the root hub? */ + unsigned msix_enabled:1; /* driver has MSI-X enabled? */ /* The next flag is a stopgap, to be removed when all the HCDs * support the new root-hub polling mechanism. */ -- cgit v1.2.1 From 40a9fb17f32dbe54de3d636142a59288544deed7 Mon Sep 17 00:00:00 2001 From: Zhang Rui Date: Fri, 17 Dec 2010 13:17:04 -0800 Subject: xhci: Do not run xhci_cleanup_msix with irq disabled when unloading xhci_hcd, I got: [ 134.856813] xhci_hcd 0000:02:00.0: remove, state 4 [ 134.858140] usb usb3: USB disconnect, address 1 [ 134.874956] xhci_hcd 0000:02:00.0: Host controller not halted, aborting reset. [ 134.876351] BUG: sleeping function called from invalid context at kernel/mutex.c:85 [ 134.877657] in_atomic(): 0, irqs_disabled(): 1, pid: 1451, name: modprobe [ 134.878975] Pid: 1451, comm: modprobe Not tainted 2.6.37-rc5+ #162 [ 134.880298] Call Trace: [ 134.881602] [] __might_sleep+0xeb/0xf0 [ 134.882921] [] mutex_lock+0x24/0x50 [ 134.884229] [] free_desc+0x2e/0x5f [ 134.885538] [] irq_free_descs+0x3b/0x71 [ 134.886853] [] free_irq_at+0x31/0x36 [ 134.888167] [] destroy_irq+0x69/0x71 [ 134.889486] [] native_teardown_msi_irq+0xe/0x10 [ 134.890820] [] default_teardown_msi_irqs+0x57/0x80 [ 134.892158] [] free_msi_irqs+0x8b/0xe9 [ 134.893504] [] pci_disable_msix+0x35/0x39 [ 134.894844] [] xhci_cleanup_msix+0x31/0x51 [xhci_hcd] [ 134.896186] [] xhci_stop+0x3a/0x80 [xhci_hcd] [ 134.897521] [] usb_remove_hcd+0xfd/0x14a [ 134.898859] [] usb_hcd_pci_remove+0x5c/0xc6 [ 134.900193] [] pci_device_remove+0x3f/0x91 [ 134.901535] [] __device_release_driver+0x83/0xd9 [ 134.902899] [] driver_detach+0x86/0xad [ 134.904222] [] bus_remove_driver+0xb2/0xd8 [ 134.905540] [] driver_unregister+0x6c/0x74 [ 134.906839] [] pci_unregister_driver+0x44/0x89 [ 134.908121] [] xhci_unregister_pci+0x15/0x17 [xhci_hcd] [ 134.909396] [] xhci_hcd_cleanup+0xe/0x10 [xhci_hcd] [ 134.910652] [] sys_delete_module+0x1ca/0x23b [ 134.911882] [] ? path_put+0x22/0x26 [ 134.913104] [] ? audit_syscall_entry+0x2c/0x148 [ 134.914333] [] system_call_fastpath+0x16/0x1b [ 134.915658] xhci_hcd 0000:02:00.0: USB bus 3 deregistered [ 134.916465] xhci_hcd 0000:02:00.0: PCI INT A disabled and the same issue when xhci_suspend is invoked. (Note from Sarah: That's fixed by Andiry's patch before this, by synchronizing the irqs rather than freeing them on suspend.) Do not run xhci_cleanup_msix with irq disabled. This patch should be queued for the 2.6.37 stable tree. Signed-off-by: Zhang Rui Signed-off-by: Sarah Sharp Cc: stable@kernel.org --- drivers/usb/host/xhci.c | 6 ++++-- 1 file changed, 4 insertions(+), 2 deletions(-) diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index d48edfa5043a..b2c56d15fb42 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -512,9 +512,10 @@ void xhci_stop(struct usb_hcd *hcd) spin_lock_irq(&xhci->lock); xhci_halt(xhci); xhci_reset(xhci); - xhci_cleanup_msix(xhci); spin_unlock_irq(&xhci->lock); + xhci_cleanup_msix(xhci); + #ifdef CONFIG_USB_XHCI_HCD_DEBUGGING /* Tell the event ring poll function not to reschedule */ xhci->zombie = 1; @@ -548,9 +549,10 @@ void xhci_shutdown(struct usb_hcd *hcd) spin_lock_irq(&xhci->lock); xhci_halt(xhci); - xhci_cleanup_msix(xhci); spin_unlock_irq(&xhci->lock); + xhci_cleanup_msix(xhci); + xhci_dbg(xhci, "xhci_shutdown completed - status = %x\n", xhci_readl(xhci, &xhci->op_regs->status)); } -- cgit v1.2.1 From 653a39d1f61bdc9f277766736d21d2e9be0391cb Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Thu, 23 Dec 2010 11:12:42 -0800 Subject: usb: Realloc xHCI structures after a hub is verified. When there's an xHCI host power loss after a suspend from memory, the USB core attempts to reset and verify the USB devices that are attached to the system. The xHCI driver has to reallocate those devices, since the hardware lost all knowledge of them during the power loss. When a hub is plugged in, and the host loses power, the xHCI hardware structures are not updated to say the device is a hub. This is usually done in hub_configure() when the USB hub is detected. That function is skipped during a reset and verify by the USB core, since the core restores the old configuration and alternate settings, and the hub driver has no idea this happened. This bug makes the xHCI host controller reject the enumeration of low speed devices under the resumed hub. Therefore, make the USB core re-setup the internal xHCI hub device information by calling update_hub_device() when hub_activate() is called for a hub reset resume. After a host power loss, all devices under the roothub get a reset-resume or a disconnect. This patch should be queued for the 2.6.37 stable tree. Signed-off-by: Sarah Sharp Cc: stable@kernel.org --- drivers/usb/core/hub.c | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+) diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c index b98efae6a1cf..4310cc4b1cb5 100644 --- a/drivers/usb/core/hub.c +++ b/drivers/usb/core/hub.c @@ -676,6 +676,8 @@ static void hub_init_func3(struct work_struct *ws); static void hub_activate(struct usb_hub *hub, enum hub_activation_type type) { struct usb_device *hdev = hub->hdev; + struct usb_hcd *hcd; + int ret; int port1; int status; bool need_debounce_delay = false; @@ -714,6 +716,25 @@ static void hub_activate(struct usb_hub *hub, enum hub_activation_type type) usb_autopm_get_interface_no_resume( to_usb_interface(hub->intfdev)); return; /* Continues at init2: below */ + } else if (type == HUB_RESET_RESUME) { + /* The internal host controller state for the hub device + * may be gone after a host power loss on system resume. + * Update the device's info so the HW knows it's a hub. + */ + hcd = bus_to_hcd(hdev->bus); + if (hcd->driver->update_hub_device) { + ret = hcd->driver->update_hub_device(hcd, hdev, + &hub->tt, GFP_NOIO); + if (ret < 0) { + dev_err(hub->intfdev, "Host not " + "accepting hub info " + "update.\n"); + dev_err(hub->intfdev, "LS/FS devices " + "and hubs may not work " + "under this hub\n."); + } + } + hub_power_on(hub, true); } else { hub_power_on(hub, true); } -- cgit v1.2.1 From a6d940dd759bf240d28624198660ed34582a327b Mon Sep 17 00:00:00 2001 From: Sarah Sharp Date: Tue, 28 Dec 2010 13:08:42 -0800 Subject: xhci: Use GFP_NOIO during device reset. When xhci_discover_or_reset_device() is called after a host controller power loss, the virtual device may need to be reallocated. Make sure xhci_alloc_dev() uses GFP_NOIO. This avoid causing a deadlock by allowing the kernel to flush pending I/O while reallocating memory for a virtual device for a USB mass storage device that's holding the backing store for dirty memory buffers. This patch should be queued for the 2.6.37 stable tree. Signed-off-by: Sarah Sharp Cc: stable@kernel.org --- drivers/usb/host/xhci.c | 8 ++++++-- 1 file changed, 6 insertions(+), 2 deletions(-) diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c index b2c56d15fb42..34cf4e165877 100644 --- a/drivers/usb/host/xhci.c +++ b/drivers/usb/host/xhci.c @@ -2431,8 +2431,12 @@ int xhci_alloc_dev(struct usb_hcd *hcd, struct usb_device *udev) xhci_err(xhci, "Error while assigning device slot ID\n"); return 0; } - /* xhci_alloc_virt_device() does not touch rings; no need to lock */ - if (!xhci_alloc_virt_device(xhci, xhci->slot_id, udev, GFP_KERNEL)) { + /* xhci_alloc_virt_device() does not touch rings; no need to lock. + * Use GFP_NOIO, since this function can be called from + * xhci_discover_or_reset_device(), which may be called as part of + * mass storage driver error handling. + */ + if (!xhci_alloc_virt_device(xhci, xhci->slot_id, udev, GFP_NOIO)) { /* Disable slot, if we can do it without mem alloc */ xhci_warn(xhci, "Could not allocate xHCI USB device data structures\n"); spin_lock_irqsave(&xhci->lock, flags); -- cgit v1.2.1 From 47cbf6925cd0ef8af4b8165b43a60b5f37c36d8a Mon Sep 17 00:00:00 2001 From: Andiry Xu Date: Mon, 20 Dec 2010 14:49:48 +0800 Subject: xHCI: fix queue_trb in isoc transfer Fix the more_trbs_coming field of queue_trb() in isoc transfer. Signed-off-by: Andiry Xu Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci-ring.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 62c70c230e83..55dc15675068 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -2900,6 +2900,7 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags, int running_total, trb_buff_len, td_len, td_remain_len, ret; u64 start_addr, addr; int i, j; + bool more_trbs_coming; ep_ring = xhci->devs[slot_id]->eps[ep_index].ring; @@ -2965,9 +2966,11 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags, */ if (j < trbs_per_td - 1) { field |= TRB_CHAIN; + more_trbs_coming = true; } else { td->last_trb = ep_ring->enqueue; field |= TRB_IOC; + more_trbs_coming = false; } /* Calculate TRB length */ @@ -2980,7 +2983,7 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags, length_field = TRB_LEN(trb_buff_len) | remainder | TRB_INTR_TARGET(0); - queue_trb(xhci, ep_ring, false, false, + queue_trb(xhci, ep_ring, false, more_trbs_coming, lower_32_bits(addr), upper_32_bits(addr), length_field, -- cgit v1.2.1 From e1eab2e00015bfe48388920ff287efdbefb6af24 Mon Sep 17 00:00:00 2001 From: Andiry Xu Date: Tue, 4 Jan 2011 16:30:39 -0800 Subject: xHCI: remove redundant parameter in giveback_first_trb() Parameter *td is not used in giveback_first_trb(). Remove it. Signed-off-by: Andiry Xu Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci-ring.c | 14 ++++++-------- 1 file changed, 6 insertions(+), 8 deletions(-) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 55dc15675068..59f81b560483 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -2414,7 +2414,7 @@ static void check_trb_math(struct urb *urb, int num_trbs, int running_total) static void giveback_first_trb(struct xhci_hcd *xhci, int slot_id, unsigned int ep_index, unsigned int stream_id, int start_cycle, - struct xhci_generic_trb *start_trb, struct xhci_td *td) + struct xhci_generic_trb *start_trb) { /* * Pass all the TRBs to the hardware at once and make sure this write @@ -2625,7 +2625,7 @@ static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags, check_trb_math(urb, num_trbs, running_total); giveback_first_trb(xhci, slot_id, ep_index, urb->stream_id, - start_cycle, start_trb, td); + start_cycle, start_trb); return 0; } @@ -2757,7 +2757,7 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, check_trb_math(urb, num_trbs, running_total); giveback_first_trb(xhci, slot_id, ep_index, urb->stream_id, - start_cycle, start_trb, td); + start_cycle, start_trb); return 0; } @@ -2859,7 +2859,7 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags, field | TRB_IOC | TRB_TYPE(TRB_STATUS) | ep_ring->cycle_state); giveback_first_trb(xhci, slot_id, ep_index, 0, - start_cycle, start_trb, td); + start_cycle, start_trb); return 0; } @@ -3006,10 +3006,8 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags, } } - wmb(); - start_trb->field[3] |= start_cycle; - - xhci_ring_ep_doorbell(xhci, slot_id, ep_index, urb->stream_id); + giveback_first_trb(xhci, slot_id, ep_index, urb->stream_id, + start_cycle, start_trb); return 0; } -- cgit v1.2.1 From 50f7b52a83a893929edf87a89ebc081ff26a7b91 Mon Sep 17 00:00:00 2001 From: Andiry Xu Date: Mon, 20 Dec 2010 15:09:34 +0800 Subject: xHCI: fix cycle bit set in giveback_first_trb() giveback_first_trb() controls the cycle bit set of the start_trb, to ensure that the start_trb is written last and the host controller will receive a whole td at a time. However, if the ring is wrapped and cycle bit is toggled to zero, then giveback_first_trb() will be of no effect. In this case, set the cycle bit of start_trb to 1 at the beginning and clear it in giveback_first_trb(). Signed-off-by: Andiry Xu Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci-ring.c | 28 +++++++++++++++++++++------- 1 file changed, 21 insertions(+), 7 deletions(-) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 59f81b560483..1ee6de92193a 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -2421,7 +2421,10 @@ static void giveback_first_trb(struct xhci_hcd *xhci, int slot_id, * isn't reordered. */ wmb(); - start_trb->field[3] |= start_cycle; + if (start_cycle) + start_trb->field[3] |= start_cycle; + else + start_trb->field[3] &= ~0x1; xhci_ring_ep_doorbell(xhci, slot_id, ep_index, stream_id); } @@ -2551,9 +2554,11 @@ static int queue_bulk_sg_tx(struct xhci_hcd *xhci, gfp_t mem_flags, u32 remainder = 0; /* Don't change the cycle bit of the first TRB until later */ - if (first_trb) + if (first_trb) { first_trb = false; - else + if (start_cycle == 0) + field |= 0x1; + } else field |= ep_ring->cycle_state; /* Chain all the TRBs together; clear the chain bit in the last @@ -2711,9 +2716,11 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, field = 0; /* Don't change the cycle bit of the first TRB until later */ - if (first_trb) + if (first_trb) { first_trb = false; - else + if (start_cycle == 0) + field |= 0x1; + } else field |= ep_ring->cycle_state; /* Chain all the TRBs together; clear the chain bit in the last @@ -2818,13 +2825,17 @@ int xhci_queue_ctrl_tx(struct xhci_hcd *xhci, gfp_t mem_flags, /* Queue setup TRB - see section 6.4.1.2.1 */ /* FIXME better way to translate setup_packet into two u32 fields? */ setup = (struct usb_ctrlrequest *) urb->setup_packet; + field = 0; + field |= TRB_IDT | TRB_TYPE(TRB_SETUP); + if (start_cycle == 0) + field |= 0x1; queue_trb(xhci, ep_ring, false, true, /* FIXME endianness is probably going to bite my ass here. */ setup->bRequestType | setup->bRequest << 8 | setup->wValue << 16, setup->wIndex | setup->wLength << 16, TRB_LEN(8) | TRB_INTR_TARGET(0), /* Immediate data in pointer */ - TRB_IDT | TRB_TYPE(TRB_SETUP)); + field); /* If there's data, queue data TRBs */ field = 0; @@ -2951,7 +2962,10 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags, field |= TRB_TYPE(TRB_ISOC); /* Assume URB_ISO_ASAP is set */ field |= TRB_SIA; - if (i > 0) + if (i == 0) { + if (start_cycle == 0) + field |= 0x1; + } else field |= ep_ring->cycle_state; first_trb = false; } else { -- cgit v1.2.1 From f2c565e223af39ed38be5c84b1a37b591b22db83 Mon Sep 17 00:00:00 2001 From: Andiry Xu Date: Mon, 20 Dec 2010 17:12:24 +0800 Subject: xHCI: replace dev_dbg() with xhci_dbg() dev_dbg() is used to print ordinary transfer messages in xhci-ring.c. System log messages will be flushed if CONFIG_USB_DEBUG is set. Replace the dev_dbg() with xhci_dbg(). Signed-off-by: Andiry Xu Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci-ring.c | 11 ++++++----- 1 file changed, 6 insertions(+), 5 deletions(-) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 1ee6de92193a..e38f7ece0a67 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -1710,8 +1710,7 @@ static int process_bulk_intr_td(struct xhci_hcd *xhci, struct xhci_td *td, /* Others already handled above */ break; } - dev_dbg(&td->urb->dev->dev, - "ep %#x - asked for %d bytes, " + xhci_dbg(xhci, "ep %#x - asked for %d bytes, " "%d bytes untransferred\n", td->urb->ep->desc.bEndpointAddress, td->urb->transfer_buffer_length, @@ -2389,7 +2388,8 @@ static unsigned int count_sg_trbs_needed(struct xhci_hcd *xhci, struct urb *urb) } xhci_dbg(xhci, "\n"); if (!in_interrupt()) - dev_dbg(&urb->dev->dev, "ep %#x - urb len = %d, sglist used, num_trbs = %d\n", + xhci_dbg(xhci, "ep %#x - urb len = %d, sglist used, " + "num_trbs = %d\n", urb->ep->desc.bEndpointAddress, urb->transfer_buffer_length, num_trbs); @@ -2676,7 +2676,8 @@ int xhci_queue_bulk_tx(struct xhci_hcd *xhci, gfp_t mem_flags, /* FIXME: this doesn't deal with URB_ZERO_PACKET - need one more */ if (!in_interrupt()) - dev_dbg(&urb->dev->dev, "ep %#x - urb len = %#x (%d), addr = %#llx, num_trbs = %d\n", + xhci_dbg(xhci, "ep %#x - urb len = %#x (%d), " + "addr = %#llx, num_trbs = %d\n", urb->ep->desc.bEndpointAddress, urb->transfer_buffer_length, urb->transfer_buffer_length, @@ -2922,7 +2923,7 @@ static int xhci_queue_isoc_tx(struct xhci_hcd *xhci, gfp_t mem_flags, } if (!in_interrupt()) - dev_dbg(&urb->dev->dev, "ep %#x - urb len = %#x (%d)," + xhci_dbg(xhci, "ep %#x - urb len = %#x (%d)," " addr = %#llx, num_tds = %d\n", urb->ep->desc.bEndpointAddress, urb->transfer_buffer_length, -- cgit v1.2.1 From 7961acd7327fe48e55abef277630abdbb3f2081a Mon Sep 17 00:00:00 2001 From: Andiry Xu Date: Mon, 20 Dec 2010 17:14:20 +0800 Subject: xHCI: fix printk_ratelimit() usage printk_ratelimit() is misused in xhci-ring.c. Signed-off-by: Andiry Xu Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci-ring.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index e38f7ece0a67..2116c0f64952 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -2452,7 +2452,7 @@ int xhci_queue_intr_tx(struct xhci_hcd *xhci, gfp_t mem_flags, * to set the polling interval (once the API is added). */ if (xhci_interval != ep_interval) { - if (!printk_ratelimit()) + if (printk_ratelimit()) dev_dbg(&urb->dev->dev, "Driver uses different interval" " (%d microframe%s) than xHCI " "(%d microframe%s)\n", @@ -3080,7 +3080,7 @@ int xhci_queue_isoc_tx_prepare(struct xhci_hcd *xhci, gfp_t mem_flags, * to set the polling interval (once the API is added). */ if (xhci_interval != ep_interval) { - if (!printk_ratelimit()) + if (printk_ratelimit()) dev_dbg(&urb->dev->dev, "Driver uses different interval" " (%d microframe%s) than xHCI " "(%d microframe%s)\n", -- cgit v1.2.1 From 50d64676d132a8a72a1a1657d7b3e6efa53da1ac Mon Sep 17 00:00:00 2001 From: Matthew Wilcox Date: Wed, 15 Dec 2010 14:18:11 -0500 Subject: xhci: Remove more doorbell-related reads The unused space in the doorbell is now marked as RsvdZ, not RsvdP, so we can avoid reading the doorbell before writing it. Update the doorbell-related defines to produce the entire doorbell value from a single macro. Document the doorbell format in a comment. Signed-off-by: Matthew Wilcox Signed-off-by: Sarah Sharp --- drivers/usb/host/xhci-ring.c | 27 +++++++++++---------------- drivers/usb/host/xhci.h | 16 ++++++---------- 2 files changed, 17 insertions(+), 26 deletions(-) diff --git a/drivers/usb/host/xhci-ring.c b/drivers/usb/host/xhci-ring.c index 2116c0f64952..3e8211c1ce5a 100644 --- a/drivers/usb/host/xhci-ring.c +++ b/drivers/usb/host/xhci-ring.c @@ -308,11 +308,8 @@ static int room_on_ring(struct xhci_hcd *xhci, struct xhci_ring *ring, /* Ring the host controller doorbell after placing a command on the ring */ void xhci_ring_cmd_db(struct xhci_hcd *xhci) { - u32 temp; - xhci_dbg(xhci, "// Ding dong!\n"); - temp = xhci_readl(xhci, &xhci->dba->doorbell[0]) & DB_MASK; - xhci_writel(xhci, temp | DB_TARGET_HOST, &xhci->dba->doorbell[0]); + xhci_writel(xhci, DB_VALUE_HOST, &xhci->dba->doorbell[0]); /* Flush PCI posted writes */ xhci_readl(xhci, &xhci->dba->doorbell[0]); } @@ -322,26 +319,24 @@ void xhci_ring_ep_doorbell(struct xhci_hcd *xhci, unsigned int ep_index, unsigned int stream_id) { - struct xhci_virt_ep *ep; - unsigned int ep_state; - u32 field; __u32 __iomem *db_addr = &xhci->dba->doorbell[slot_id]; + struct xhci_virt_ep *ep = &xhci->devs[slot_id]->eps[ep_index]; + unsigned int ep_state = ep->ep_state; - ep = &xhci->devs[slot_id]->eps[ep_index]; - ep_state = ep->ep_state; /* Don't ring the doorbell for this endpoint if there are pending - * cancellations because the we don't want to interrupt processing. + * cancellations because we don't want to interrupt processing. * We don't want to restart any stream rings if there's a set dequeue * pointer command pending because the device can choose to start any * stream once the endpoint is on the HW schedule. * FIXME - check all the stream rings for pending cancellations. */ - if (!(ep_state & EP_HALT_PENDING) && !(ep_state & SET_DEQ_PENDING) - && !(ep_state & EP_HALTED)) { - field = xhci_readl(xhci, db_addr) & DB_MASK; - field |= EPI_TO_DB(ep_index) | STREAM_ID_TO_DB(stream_id); - xhci_writel(xhci, field, db_addr); - } + if ((ep_state & EP_HALT_PENDING) || (ep_state & SET_DEQ_PENDING) || + (ep_state & EP_HALTED)) + return; + xhci_writel(xhci, DB_VALUE(ep_index, stream_id), db_addr); + /* The CPU has better things to do at this point than wait for a + * write-posting flush. It'll get there soon enough. + */ } /* Ring the doorbell for any rings with pending URBs */ diff --git a/drivers/usb/host/xhci.h b/drivers/usb/host/xhci.h index 170c367112d2..7f236fd22015 100644 --- a/drivers/usb/host/xhci.h +++ b/drivers/usb/host/xhci.h @@ -436,22 +436,18 @@ struct xhci_run_regs { /** * struct doorbell_array * + * Bits 0 - 7: Endpoint target + * Bits 8 - 15: RsvdZ + * Bits 16 - 31: Stream ID + * * Section 5.6 */ struct xhci_doorbell_array { u32 doorbell[256]; }; -#define DB_TARGET_MASK 0xFFFFFF00 -#define DB_STREAM_ID_MASK 0x0000FFFF -#define DB_TARGET_HOST 0x0 -#define DB_STREAM_ID_HOST 0x0 -#define DB_MASK (0xff << 8) - -/* Endpoint Target - bits 0:7 */ -#define EPI_TO_DB(p) (((p) + 1) & 0xff) -#define STREAM_ID_TO_DB(p) (((p) & 0xffff) << 16) - +#define DB_VALUE(ep, stream) ((((ep) + 1) & 0xff) | ((stream) << 16)) +#define DB_VALUE_HOST 0x00000000 /** * struct xhci_protocol_caps -- cgit v1.2.1 From cae41118f50ef0c431e13159df6d7dd8bbd54004 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Richard=20Sch=C3=BCtz?= Date: Sun, 19 Dec 2010 21:18:38 +0100 Subject: USB: usb-storage: unusual_devs update for Cypress ATACB MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit New device ID added for unusual Cypress ATACB device. Signed-off-by: Richard Schütz Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/unusual_cypress.h | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/drivers/usb/storage/unusual_cypress.h b/drivers/usb/storage/unusual_cypress.h index c854fdebe0ae..2c8553026222 100644 --- a/drivers/usb/storage/unusual_cypress.h +++ b/drivers/usb/storage/unusual_cypress.h @@ -31,4 +31,9 @@ UNUSUAL_DEV( 0x04b4, 0x6831, 0x0000, 0x9999, "Cypress ISD-300LP", USB_SC_CYP_ATACB, USB_PR_DEVICE, NULL, 0), +UNUSUAL_DEV( 0x14cd, 0x6116, 0x0000, 0x9999, + "Super Top", + "USB 2.0 SATA BRIDGE", + USB_SC_CYP_ATACB, USB_PR_DEVICE, NULL, 0), + #endif /* defined(CONFIG_USB_STORAGE_CYPRESS_ATACB) || ... */ -- cgit v1.2.1 From 7e1e7bd9dbd469267b6e6de1bf8d71a7d65ce86a Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Richard=20Sch=C3=BCtz?= Date: Wed, 22 Dec 2010 14:28:56 +0100 Subject: USB: usb-storage: unusual_devs update for TrekStor DataStation maxi g.u external hard drive enclosure MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The TrekStor DataStation maxi g.u external hard drive enclosure uses a JMicron USB to SATA chip which needs the US_FL_IGNORE_RESIDUE flag to work properly. Signed-off-by: Richard Schütz Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/unusual_devs.h | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h index fcc1e32ce256..2e630e6fadad 100644 --- a/drivers/usb/storage/unusual_devs.h +++ b/drivers/usb/storage/unusual_devs.h @@ -1872,6 +1872,15 @@ UNUSUAL_DEV( 0x1908, 0x3335, 0x0200, 0x0200, USB_SC_DEVICE, USB_PR_DEVICE, NULL, US_FL_NO_READ_DISC_INFO ), +/* Patch by Richard Schütz + * This external hard drive enclosure uses a JMicron chip which + * needs the US_FL_IGNORE_RESIDUE flag to work properly. */ +UNUSUAL_DEV( 0x1e68, 0x001b, 0x0000, 0x0000, + "TrekStor GmbH & Co. KG", + "DataStation maxi g.u", + USB_SC_DEVICE, USB_PR_DEVICE, NULL, + US_FL_IGNORE_RESIDUE | US_FL_SANE_SENSE ), + UNUSUAL_DEV( 0x2116, 0x0320, 0x0001, 0x0001, "ST", "2A", -- cgit v1.2.1 From a58861fbde2a350df4d27fc62fb42905669b37ce Mon Sep 17 00:00:00 2001 From: Dan Williams Date: Fri, 31 Dec 2010 10:51:51 -0600 Subject: USB: qcaux: add Pantech UML290 device ID Another CDC-ACM + vendor specific interface layout for the QCDM port. Signed-off-by: Dan Williams Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/qcaux.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/usb/serial/qcaux.c b/drivers/usb/serial/qcaux.c index 214a3e504292..b53865b8cd9c 100644 --- a/drivers/usb/serial/qcaux.c +++ b/drivers/usb/serial/qcaux.c @@ -36,6 +36,7 @@ #define UTSTARCOM_PRODUCT_UM175_V1 0x3712 #define UTSTARCOM_PRODUCT_UM175_V2 0x3714 #define UTSTARCOM_PRODUCT_UM175_ALLTEL 0x3715 +#define PANTECH_PRODUCT_UML290_VZW 0x3718 /* CMOTECH devices */ #define CMOTECH_VENDOR_ID 0x16d8 @@ -66,6 +67,7 @@ static struct usb_device_id id_table[] = { { USB_DEVICE_AND_INTERFACE_INFO(LG_VENDOR_ID, LG_PRODUCT_VX4400_6000, 0xff, 0xff, 0x00) }, { USB_DEVICE_AND_INTERFACE_INFO(SANYO_VENDOR_ID, SANYO_PRODUCT_KATANA_LX, 0xff, 0xff, 0x00) }, { USB_DEVICE_AND_INTERFACE_INFO(SAMSUNG_VENDOR_ID, SAMSUNG_PRODUCT_U520, 0xff, 0x00, 0x00) }, + { USB_DEVICE_AND_INTERFACE_INFO(UTSTARCOM_VENDOR_ID, PANTECH_PRODUCT_UML290_VZW, 0xff, 0xff, 0xff) }, { }, }; MODULE_DEVICE_TABLE(usb, id_table); -- cgit v1.2.1 From faea63f7ccfddfb8fc19798799fcd38c58415172 Mon Sep 17 00:00:00 2001 From: Craig Shelley Date: Sun, 2 Jan 2011 21:51:46 +0000 Subject: USB: CP210x Add two device IDs Device Ids added for IRZ Automation Teleport SG-10 GSM/GPRS Modem and DekTec DTA Plus VHF/UHF Booster/Attenuator. Signed-off-by: Craig Shelley Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/cp210x.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c index 8d7731dbf478..f5fe0ed1a48d 100644 --- a/drivers/usb/serial/cp210x.c +++ b/drivers/usb/serial/cp210x.c @@ -110,7 +110,9 @@ static const struct usb_device_id id_table[] = { { USB_DEVICE(0x10C4, 0x8341) }, /* Siemens MC35PU GPRS Modem */ { USB_DEVICE(0x10C4, 0x8382) }, /* Cygnal Integrated Products, Inc. */ { USB_DEVICE(0x10C4, 0x83A8) }, /* Amber Wireless AMB2560 */ + { USB_DEVICE(0x10C4, 0x83D8) }, /* DekTec DTA Plus VHF/UHF Booster/Attenuator */ { USB_DEVICE(0x10C4, 0x8411) }, /* Kyocera GPS Module */ + { USB_DEVICE(0x10C4, 0x8418) }, /* IRZ Automation Teleport SG-10 GSM/GPRS Modem */ { USB_DEVICE(0x10C4, 0x846E) }, /* BEI USB Sensor Interface (VCP) */ { USB_DEVICE(0x10C4, 0x8477) }, /* Balluff RFID */ { USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */ -- cgit v1.2.1 From 9926c0df7b31b2128eebe92e0e2b052f380ea464 Mon Sep 17 00:00:00 2001 From: Craig Shelley Date: Sun, 2 Jan 2011 21:59:08 +0000 Subject: USB: CP210x Removed incorrect device ID Device ID removed 0x10C4/0x8149 for West Mountain Radio Computerized Battery Analyzer. This device is actually based on a SiLabs C8051Fxxx, see http://www.etheus.net/SiUSBXp_Linux_Driver for further info. Signed-off-by: Craig Shelley Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/cp210x.c | 1 - 1 file changed, 1 deletion(-) diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c index f5fe0ed1a48d..c3bea46e87fb 100644 --- a/drivers/usb/serial/cp210x.c +++ b/drivers/usb/serial/cp210x.c @@ -87,7 +87,6 @@ static const struct usb_device_id id_table[] = { { USB_DEVICE(0x10C4, 0x8115) }, /* Arygon NFC/Mifare Reader */ { USB_DEVICE(0x10C4, 0x813D) }, /* Burnside Telecom Deskmobile */ { USB_DEVICE(0x10C4, 0x813F) }, /* Tams Master Easy Control */ - { USB_DEVICE(0x10C4, 0x8149) }, /* West Mountain Radio Computerized Battery Analyzer */ { USB_DEVICE(0x10C4, 0x814A) }, /* West Mountain Radio RIGblaster P&P */ { USB_DEVICE(0x10C4, 0x814B) }, /* West Mountain Radio RIGtalk */ { USB_DEVICE(0x10C4, 0x8156) }, /* B&G H3000 link cable */ -- cgit v1.2.1 From 12f68c480c7155a66bd2a76ab2fef28dd5f93fa2 Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Mon, 3 Jan 2011 16:47:49 -0500 Subject: USB: usb-storage: unusual_devs entry for CamSport Evo This patch (as1438) adds an unusual_devs entry for the MagicPixel FW_Omega2 chip, used in the CamSport Evo camera. The firmware incorrectly reports a vendor-specific bDeviceClass. Signed-off-by: Alan Stern Reported-by: Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/storage/unusual_devs.h | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/drivers/usb/storage/unusual_devs.h b/drivers/usb/storage/unusual_devs.h index 2e630e6fadad..24bd5d7c3deb 100644 --- a/drivers/usb/storage/unusual_devs.h +++ b/drivers/usb/storage/unusual_devs.h @@ -1044,6 +1044,15 @@ UNUSUAL_DEV( 0x084d, 0x0011, 0x0110, 0x0110, USB_SC_DEVICE, USB_PR_DEVICE, NULL, US_FL_BULK32), +/* Reported by + * The device reports a vendor-specific device class, requiring an + * explicit vendor/product match. + */ +UNUSUAL_DEV( 0x0851, 0x1542, 0x0002, 0x0002, + "MagicPixel", + "FW_Omega2", + USB_SC_DEVICE, USB_PR_DEVICE, NULL, 0), + /* Andrew Lunn * PanDigital Digital Picture Frame. Does not like ALLOW_MEDIUM_REMOVAL * on LUN 4. -- cgit v1.2.1 From 1e4cba8bd2cddd10849e769ff502e255c27c81b4 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Mon, 20 Dec 2010 21:54:30 -0200 Subject: usb: otg: Make USB3319 ULPI ID generic On a system with a USB3317 ULPI transceiver the following message is shown on kernel boot: ULPI transceiver vendor/product ID 0x0424/0x0006 Found SMSC USB3319 ULPI transceiver. ULPI integrity check: passed. The reason is that USB3317 has the same vendor/product ID as USB3319. Make the ULPI ID generic for the USB331x transceivers. Signed-off-by: Fabio Estevam Acked-by: Igor Grinberg Signed-off-by: Greg Kroah-Hartman --- drivers/usb/otg/ulpi.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/otg/ulpi.c b/drivers/usb/otg/ulpi.c index 059d9ac0ab5b..770d799d5afb 100644 --- a/drivers/usb/otg/ulpi.c +++ b/drivers/usb/otg/ulpi.c @@ -45,7 +45,7 @@ struct ulpi_info { /* ULPI hardcoded IDs, used for probing */ static struct ulpi_info ulpi_ids[] = { ULPI_INFO(ULPI_ID(0x04cc, 0x1504), "NXP ISP1504"), - ULPI_INFO(ULPI_ID(0x0424, 0x0006), "SMSC USB3319"), + ULPI_INFO(ULPI_ID(0x0424, 0x0006), "SMSC USB331x"), }; static int ulpi_set_otg_flags(struct otg_transceiver *otg) -- cgit v1.2.1 From baab93afc2844b68d57b0dcca5e1d34c5d7cf411 Mon Sep 17 00:00:00 2001 From: Alex He Date: Tue, 21 Dec 2010 17:45:46 +0800 Subject: USB: EHCI: ASPM quirk of ISOC on AMD Hudson AMD Hudson also needs the same ASPM quirk as SB800 Signed-off-by: Alex He Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-pci.c | 33 ++++++++++++++++++++------------- 1 file changed, 20 insertions(+), 13 deletions(-) diff --git a/drivers/usb/host/ehci-pci.c b/drivers/usb/host/ehci-pci.c index 76179c39c0e3..bed07d4aab06 100644 --- a/drivers/usb/host/ehci-pci.c +++ b/drivers/usb/host/ehci-pci.c @@ -44,28 +44,35 @@ static int ehci_pci_reinit(struct ehci_hcd *ehci, struct pci_dev *pdev) return 0; } -static int ehci_quirk_amd_SB800(struct ehci_hcd *ehci) +static int ehci_quirk_amd_hudson(struct ehci_hcd *ehci) { struct pci_dev *amd_smbus_dev; u8 rev = 0; amd_smbus_dev = pci_get_device(PCI_VENDOR_ID_ATI, 0x4385, NULL); - if (!amd_smbus_dev) - return 0; - - pci_read_config_byte(amd_smbus_dev, PCI_REVISION_ID, &rev); - if (rev < 0x40) { - pci_dev_put(amd_smbus_dev); - amd_smbus_dev = NULL; - return 0; + if (amd_smbus_dev) { + pci_read_config_byte(amd_smbus_dev, PCI_REVISION_ID, &rev); + if (rev < 0x40) { + pci_dev_put(amd_smbus_dev); + amd_smbus_dev = NULL; + return 0; + } + } else { + amd_smbus_dev = pci_get_device(PCI_VENDOR_ID_AMD, 0x780b, NULL); + if (!amd_smbus_dev) + return 0; + pci_read_config_byte(amd_smbus_dev, PCI_REVISION_ID, &rev); + if (rev < 0x11 || rev > 0x18) { + pci_dev_put(amd_smbus_dev); + amd_smbus_dev = NULL; + return 0; + } } if (!amd_nb_dev) amd_nb_dev = pci_get_device(PCI_VENDOR_ID_AMD, 0x1510, NULL); - if (!amd_nb_dev) - ehci_err(ehci, "QUIRK: unable to get AMD NB device\n"); - ehci_info(ehci, "QUIRK: Enable AMD SB800 L1 fix\n"); + ehci_info(ehci, "QUIRK: Enable exception for AMD Hudson ASPM\n"); pci_dev_put(amd_smbus_dev); amd_smbus_dev = NULL; @@ -131,7 +138,7 @@ static int ehci_pci_setup(struct usb_hcd *hcd) /* cache this readonly data; minimize chip reads */ ehci->hcs_params = ehci_readl(ehci, &ehci->caps->hcs_params); - if (ehci_quirk_amd_SB800(ehci)) + if (ehci_quirk_amd_hudson(ehci)) ehci->amd_l1_fix = 1; retval = ehci_halt(ehci); -- cgit v1.2.1 From 952eca0a95e27660f7a56a7186b9bd09d791ced4 Mon Sep 17 00:00:00 2001 From: Melchior FRANZ Date: Wed, 22 Dec 2010 13:55:24 +0100 Subject: USB: DL100B webmail notifier: initialize return value If case of an unknown usb_device_id->driver_info (which could only occur if the info got corrupted somewhere outside the usbled driver), a debug message depended on an uninitialized value. This was harmless, but ugly, and gets fixed with this patch. Signed-off-by: Melchior FRANZ Signed-off-by: Greg Kroah-Hartman --- drivers/usb/misc/usbled.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/misc/usbled.c b/drivers/usb/misc/usbled.c index 1732d9bc097e..1616ad1793a4 100644 --- a/drivers/usb/misc/usbled.c +++ b/drivers/usb/misc/usbled.c @@ -45,7 +45,7 @@ struct usb_led { static void change_color(struct usb_led *led) { - int retval; + int retval = 0; unsigned char *buffer; buffer = kmalloc(8, GFP_KERNEL); -- cgit v1.2.1 From 0cdfb819b6a97e79c7a0aa0c471cd7000367103b Mon Sep 17 00:00:00 2001 From: David Sterba Date: Mon, 27 Dec 2010 18:49:58 +0100 Subject: USB: cdc-wdm: fix misuse of logical operation in place of bitop CC: Greg Kroah-Hartman CC: Oliver Neukum CC: Marcel Holtmann Signed-off-by: David Sterba Signed-off-by: Greg Kroah-Hartman --- drivers/usb/class/cdc-wdm.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/class/cdc-wdm.c b/drivers/usb/class/cdc-wdm.c index 6ee4451bfe2d..47085e5879ab 100644 --- a/drivers/usb/class/cdc-wdm.c +++ b/drivers/usb/class/cdc-wdm.c @@ -342,7 +342,7 @@ static ssize_t wdm_write goto outnp; } - if (!file->f_flags && O_NONBLOCK) + if (!(file->f_flags & O_NONBLOCK)) r = wait_event_interruptible(desc->wait, !test_bit(WDM_IN_USE, &desc->flags)); else -- cgit v1.2.1 From 20831ad23978d0543b0b23128621b6d8ee7757f1 Mon Sep 17 00:00:00 2001 From: Ming Lei Date: Tue, 4 Jan 2011 20:21:32 +0800 Subject: usb: otg: nop: fix oops triggered by otg_register_notifier This patch adds BLOCKING_INIT_NOTIFIER_HEAD in nop_usb_xceiv_probe, so that we can avoid oops caused by uninitialized nop->otg.notifier.rwsem which will be touched in otg_register_notifier path. Reported-by: Gupta, Ajay Kumar Tested-by: Gupta, Ajay Kumar Cc: Balbi, Felipe Cc: David Brownell Signed-off-by: Ming Lei Signed-off-by: Greg Kroah-Hartman --- drivers/usb/otg/nop-usb-xceiv.c | 2 ++ 1 file changed, 2 insertions(+) diff --git a/drivers/usb/otg/nop-usb-xceiv.c b/drivers/usb/otg/nop-usb-xceiv.c index e70014ab0976..8acf165fe13b 100644 --- a/drivers/usb/otg/nop-usb-xceiv.c +++ b/drivers/usb/otg/nop-usb-xceiv.c @@ -132,6 +132,8 @@ static int __devinit nop_usb_xceiv_probe(struct platform_device *pdev) platform_set_drvdata(pdev, nop); + BLOCKING_INIT_NOTIFIER_HEAD(&nop->otg.notifier); + return 0; exit: kfree(nop); -- cgit v1.2.1 From 956227120f2e8eed8ca459879d7eafee78591cc1 Mon Sep 17 00:00:00 2001 From: Peter Chen Date: Wed, 5 Jan 2011 14:50:54 +0800 Subject: usb: set ep_dev async suspend should be later than device_initialize The dev->power.async_suspend can only be set at the condition of dev->power.status is DPM_ON. The dev->power.status will be initialized as DPM_ON at device_initialize. Signed-off-by: Peter Chen Acked-by: Alan Stern Signed-off-by: Greg Kroah-Hartman --- drivers/usb/core/endpoint.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/core/endpoint.c b/drivers/usb/core/endpoint.c index 9da250563027..df502a98d0df 100644 --- a/drivers/usb/core/endpoint.c +++ b/drivers/usb/core/endpoint.c @@ -192,12 +192,12 @@ int usb_create_ep_devs(struct device *parent, ep_dev->dev.parent = parent; ep_dev->dev.release = ep_device_release; dev_set_name(&ep_dev->dev, "ep_%02x", endpoint->desc.bEndpointAddress); - device_enable_async_suspend(&ep_dev->dev); retval = device_register(&ep_dev->dev); if (retval) goto error_register; + device_enable_async_suspend(&ep_dev->dev); endpoint->ep_dev = ep_dev; return retval; -- cgit v1.2.1 From abab0c67c061612cf559ab27ce1340774d7c292d Mon Sep 17 00:00:00 2001 From: Toshiharu Okada Date: Wed, 29 Dec 2010 10:07:33 +0900 Subject: usb: pch_udc: Fixed issue which does not work with g_serial This PCH_UDC driver does not work normally when "Serial gadget" is used. The receiving data of control transmission (EP0 Control OUT Transaction) has not received correctly. This patch fixed this issue. The following was modified. - The buffer size. - The change processing of a receiving buffer (The temporary buffer and the buffer prepared by gadget). - The setup processing of a DMA descriptor. Currently the PCH_UDC driver can work normally with "Serial gadget" or "File-backed Storage Gadget". Signed-off-by: Toshiharu Okada Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/pch_udc.c | 117 +++++++++++++++++++++++++------------------ 1 file changed, 67 insertions(+), 50 deletions(-) diff --git a/drivers/usb/gadget/pch_udc.c b/drivers/usb/gadget/pch_udc.c index 0c8dd81dddca..dfe927b01ffb 100644 --- a/drivers/usb/gadget/pch_udc.c +++ b/drivers/usb/gadget/pch_udc.c @@ -198,10 +198,10 @@ #define PCH_UDC_BRLEN 0x0F /* Burst length */ #define PCH_UDC_THLEN 0x1F /* Threshold length */ /* Value of EP Buffer Size */ -#define UDC_EP0IN_BUFF_SIZE 64 -#define UDC_EPIN_BUFF_SIZE 512 -#define UDC_EP0OUT_BUFF_SIZE 64 -#define UDC_EPOUT_BUFF_SIZE 512 +#define UDC_EP0IN_BUFF_SIZE 16 +#define UDC_EPIN_BUFF_SIZE 256 +#define UDC_EP0OUT_BUFF_SIZE 16 +#define UDC_EPOUT_BUFF_SIZE 256 /* Value of EP maximum packet size */ #define UDC_EP0IN_MAX_PKT_SIZE 64 #define UDC_EP0OUT_MAX_PKT_SIZE 64 @@ -351,7 +351,7 @@ struct pch_udc_dev { struct pci_pool *data_requests; struct pci_pool *stp_requests; dma_addr_t dma_addr; - unsigned long ep0out_buf[64]; + void *ep0out_buf; struct usb_ctrlrequest setup_data; unsigned long phys_addr; void __iomem *base_addr; @@ -1219,11 +1219,11 @@ static void complete_req(struct pch_udc_ep *ep, struct pch_udc_request *req, dev = ep->dev; if (req->dma_mapped) { if (ep->in) - pci_unmap_single(dev->pdev, req->req.dma, - req->req.length, PCI_DMA_TODEVICE); + dma_unmap_single(&dev->pdev->dev, req->req.dma, + req->req.length, DMA_TO_DEVICE); else - pci_unmap_single(dev->pdev, req->req.dma, - req->req.length, PCI_DMA_FROMDEVICE); + dma_unmap_single(&dev->pdev->dev, req->req.dma, + req->req.length, DMA_FROM_DEVICE); req->dma_mapped = 0; req->req.dma = DMA_ADDR_INVALID; } @@ -1414,7 +1414,6 @@ static void pch_udc_start_rxrequest(struct pch_udc_ep *ep, pch_udc_clear_dma(ep->dev, DMA_DIR_RX); td_data = req->td_data; - ep->td_data = req->td_data; /* Set the status bits for all descriptors */ while (1) { td_data->status = (td_data->status & ~PCH_UDC_BUFF_STS) | @@ -1613,15 +1612,19 @@ static int pch_udc_pcd_queue(struct usb_ep *usbep, struct usb_request *usbreq, if (usbreq->length && ((usbreq->dma == DMA_ADDR_INVALID) || !usbreq->dma)) { if (ep->in) - usbreq->dma = pci_map_single(dev->pdev, usbreq->buf, - usbreq->length, PCI_DMA_TODEVICE); + usbreq->dma = dma_map_single(&dev->pdev->dev, + usbreq->buf, + usbreq->length, + DMA_TO_DEVICE); else - usbreq->dma = pci_map_single(dev->pdev, usbreq->buf, - usbreq->length, PCI_DMA_FROMDEVICE); + usbreq->dma = dma_map_single(&dev->pdev->dev, + usbreq->buf, + usbreq->length, + DMA_FROM_DEVICE); req->dma_mapped = 1; } if (usbreq->length > 0) { - retval = prepare_dma(ep, req, gfp); + retval = prepare_dma(ep, req, GFP_ATOMIC); if (retval) goto probe_end; } @@ -1646,7 +1649,6 @@ static int pch_udc_pcd_queue(struct usb_ep *usbep, struct usb_request *usbreq, pch_udc_wait_ep_stall(ep); pch_udc_ep_clear_nak(ep); pch_udc_enable_ep_interrupts(ep->dev, (1 << ep->num)); - pch_udc_set_dma(dev, DMA_DIR_TX); } } /* Now add this request to the ep's pending requests */ @@ -1926,6 +1928,7 @@ static void pch_udc_complete_receiver(struct pch_udc_ep *ep) PCH_UDC_BS_DMA_DONE) return; pch_udc_clear_dma(ep->dev, DMA_DIR_RX); + pch_udc_ep_set_ddptr(ep, 0); if ((req->td_data_last->status & PCH_UDC_RXTX_STS) != PCH_UDC_RTS_SUCC) { dev_err(&dev->pdev->dev, "Invalid RXTX status (0x%08x) " @@ -1963,7 +1966,7 @@ static void pch_udc_svc_data_in(struct pch_udc_dev *dev, int ep_num) u32 epsts; struct pch_udc_ep *ep; - ep = &dev->ep[2*ep_num]; + ep = &dev->ep[UDC_EPIN_IDX(ep_num)]; epsts = ep->epsts; ep->epsts = 0; @@ -2008,7 +2011,7 @@ static void pch_udc_svc_data_out(struct pch_udc_dev *dev, int ep_num) struct pch_udc_ep *ep; struct pch_udc_request *req = NULL; - ep = &dev->ep[2*ep_num + 1]; + ep = &dev->ep[UDC_EPOUT_IDX(ep_num)]; epsts = ep->epsts; ep->epsts = 0; @@ -2025,10 +2028,11 @@ static void pch_udc_svc_data_out(struct pch_udc_dev *dev, int ep_num) } if (epsts & UDC_EPSTS_HE) return; - if (epsts & UDC_EPSTS_RSS) + if (epsts & UDC_EPSTS_RSS) { pch_udc_ep_set_stall(ep); pch_udc_enable_ep_interrupts(ep->dev, PCH_UDC_EPINT(ep->in, ep->num)); + } if (epsts & UDC_EPSTS_RCS) { if (!dev->prot_stall) { pch_udc_ep_clear_stall(ep); @@ -2060,8 +2064,10 @@ static void pch_udc_svc_control_in(struct pch_udc_dev *dev) { u32 epsts; struct pch_udc_ep *ep; + struct pch_udc_ep *ep_out; ep = &dev->ep[UDC_EP0IN_IDX]; + ep_out = &dev->ep[UDC_EP0OUT_IDX]; epsts = ep->epsts; ep->epsts = 0; @@ -2073,8 +2079,16 @@ static void pch_udc_svc_control_in(struct pch_udc_dev *dev) return; if (epsts & UDC_EPSTS_HE) return; - if ((epsts & UDC_EPSTS_TDC) && (!dev->stall)) + if ((epsts & UDC_EPSTS_TDC) && (!dev->stall)) { pch_udc_complete_transfer(ep); + pch_udc_clear_dma(dev, DMA_DIR_RX); + ep_out->td_data->status = (ep_out->td_data->status & + ~PCH_UDC_BUFF_STS) | + PCH_UDC_BS_HST_RDY; + pch_udc_ep_clear_nak(ep_out); + pch_udc_set_dma(dev, DMA_DIR_RX); + pch_udc_ep_set_rrdy(ep_out); + } /* On IN interrupt, provide data if we have any */ if ((epsts & UDC_EPSTS_IN) && !(epsts & UDC_EPSTS_TDC) && !(epsts & UDC_EPSTS_TXEMPTY)) @@ -2102,11 +2116,9 @@ static void pch_udc_svc_control_out(struct pch_udc_dev *dev) dev->stall = 0; dev->ep[UDC_EP0IN_IDX].halted = 0; dev->ep[UDC_EP0OUT_IDX].halted = 0; - /* In data not ready */ - pch_udc_ep_set_nak(&(dev->ep[UDC_EP0IN_IDX])); dev->setup_data = ep->td_stp->request; pch_udc_init_setup_buff(ep->td_stp); - pch_udc_clear_dma(dev, DMA_DIR_TX); + pch_udc_clear_dma(dev, DMA_DIR_RX); pch_udc_ep_fifo_flush(&(dev->ep[UDC_EP0IN_IDX]), dev->ep[UDC_EP0IN_IDX].in); if ((dev->setup_data.bRequestType & USB_DIR_IN)) @@ -2122,14 +2134,23 @@ static void pch_udc_svc_control_out(struct pch_udc_dev *dev) setup_supported = dev->driver->setup(&dev->gadget, &dev->setup_data); spin_lock(&dev->lock); + + if (dev->setup_data.bRequestType & USB_DIR_IN) { + ep->td_data->status = (ep->td_data->status & + ~PCH_UDC_BUFF_STS) | + PCH_UDC_BS_HST_RDY; + pch_udc_ep_set_ddptr(ep, ep->td_data_phys); + } /* ep0 in returns data on IN phase */ if (setup_supported >= 0 && setup_supported < UDC_EP0IN_MAX_PKT_SIZE) { pch_udc_ep_clear_nak(&(dev->ep[UDC_EP0IN_IDX])); /* Gadget would have queued a request when * we called the setup */ - pch_udc_set_dma(dev, DMA_DIR_RX); - pch_udc_ep_clear_nak(ep); + if (!(dev->setup_data.bRequestType & USB_DIR_IN)) { + pch_udc_set_dma(dev, DMA_DIR_RX); + pch_udc_ep_clear_nak(ep); + } } else if (setup_supported < 0) { /* if unsupported request, then stall */ pch_udc_ep_set_stall(&(dev->ep[UDC_EP0IN_IDX])); @@ -2142,22 +2163,13 @@ static void pch_udc_svc_control_out(struct pch_udc_dev *dev) } } else if ((((stat & UDC_EPSTS_OUT_MASK) >> UDC_EPSTS_OUT_SHIFT) == UDC_EPSTS_OUT_DATA) && !dev->stall) { - if (list_empty(&ep->queue)) { - dev_err(&dev->pdev->dev, "%s: No request\n", __func__); - ep->td_data->status = (ep->td_data->status & - ~PCH_UDC_BUFF_STS) | - PCH_UDC_BS_HST_RDY; - pch_udc_set_dma(dev, DMA_DIR_RX); - } else { - /* control write */ - /* next function will pickuo an clear the status */ + pch_udc_clear_dma(dev, DMA_DIR_RX); + pch_udc_ep_set_ddptr(ep, 0); + if (!list_empty(&ep->queue)) { ep->epsts = stat; - - pch_udc_svc_data_out(dev, 0); - /* re-program desc. pointer for possible ZLPs */ - pch_udc_ep_set_ddptr(ep, ep->td_data_phys); - pch_udc_set_dma(dev, DMA_DIR_RX); + pch_udc_svc_data_out(dev, PCH_UDC_EP0); } + pch_udc_set_dma(dev, DMA_DIR_RX); } pch_udc_ep_set_rrdy(ep); } @@ -2174,7 +2186,7 @@ static void pch_udc_postsvc_epinters(struct pch_udc_dev *dev, int ep_num) struct pch_udc_ep *ep; struct pch_udc_request *req; - ep = &dev->ep[2*ep_num]; + ep = &dev->ep[UDC_EPIN_IDX(ep_num)]; if (!list_empty(&ep->queue)) { req = list_entry(ep->queue.next, struct pch_udc_request, queue); pch_udc_enable_ep_interrupts(ep->dev, @@ -2196,13 +2208,13 @@ static void pch_udc_read_all_epstatus(struct pch_udc_dev *dev, u32 ep_intr) for (i = 0; i < PCH_UDC_USED_EP_NUM; i++) { /* IN */ if (ep_intr & (0x1 << i)) { - ep = &dev->ep[2*i]; + ep = &dev->ep[UDC_EPIN_IDX(i)]; ep->epsts = pch_udc_read_ep_status(ep); pch_udc_clear_ep_status(ep, ep->epsts); } /* OUT */ if (ep_intr & (0x10000 << i)) { - ep = &dev->ep[2*i+1]; + ep = &dev->ep[UDC_EPOUT_IDX(i)]; ep->epsts = pch_udc_read_ep_status(ep); pch_udc_clear_ep_status(ep, ep->epsts); } @@ -2563,9 +2575,6 @@ static void pch_udc_pcd_reinit(struct pch_udc_dev *dev) dev->ep[UDC_EP0IN_IDX].ep.maxpacket = UDC_EP0IN_MAX_PKT_SIZE; dev->ep[UDC_EP0OUT_IDX].ep.maxpacket = UDC_EP0OUT_MAX_PKT_SIZE; - dev->dma_addr = pci_map_single(dev->pdev, dev->ep0out_buf, 256, - PCI_DMA_FROMDEVICE); - /* remove ep0 in and out from the list. They have own pointer */ list_del_init(&dev->ep[UDC_EP0IN_IDX].ep.ep_list); list_del_init(&dev->ep[UDC_EP0OUT_IDX].ep.ep_list); @@ -2637,6 +2646,13 @@ static int init_dma_pools(struct pch_udc_dev *dev) dev->ep[UDC_EP0IN_IDX].td_stp_phys = 0; dev->ep[UDC_EP0IN_IDX].td_data = NULL; dev->ep[UDC_EP0IN_IDX].td_data_phys = 0; + + dev->ep0out_buf = kzalloc(UDC_EP0OUT_BUFF_SIZE * 4, GFP_KERNEL); + if (!dev->ep0out_buf) + return -ENOMEM; + dev->dma_addr = dma_map_single(&dev->pdev->dev, dev->ep0out_buf, + UDC_EP0OUT_BUFF_SIZE * 4, + DMA_FROM_DEVICE); return 0; } @@ -2750,6 +2766,11 @@ static void pch_udc_remove(struct pci_dev *pdev) pci_pool_destroy(dev->stp_requests); } + if (dev->dma_addr) + dma_unmap_single(&dev->pdev->dev, dev->dma_addr, + UDC_EP0OUT_BUFF_SIZE * 4, DMA_FROM_DEVICE); + kfree(dev->ep0out_buf); + pch_udc_exit(dev); if (dev->irq_registered) @@ -2792,11 +2813,7 @@ static int pch_udc_resume(struct pci_dev *pdev) int ret; pci_set_power_state(pdev, PCI_D0); - ret = pci_restore_state(pdev); - if (ret) { - dev_err(&pdev->dev, "%s: pci_restore_state failed\n", __func__); - return ret; - } + pci_restore_state(pdev); ret = pci_enable_device(pdev); if (ret) { dev_err(&pdev->dev, "%s: pci_enable_device failed\n", __func__); -- cgit v1.2.1 From 06f1b9715c324589b42be69ad33422b83bd42f02 Mon Sep 17 00:00:00 2001 From: Tomoya MORINAGA Date: Thu, 6 Jan 2011 09:16:31 +0900 Subject: USB: pch_udc: support new device ML7213 IOH Support new device OKI SEMICONDUCTOR's ML7213 IOH(Input/Output Hub) which is for IVI(In-Vehicle Infotainment) use. The ML7213 is companion chip for Intel Atom E6xx series. The ML7213 is completely compatible for Intel EG20T PCH. Signed-off-by: Tomoya MORINAGA Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/Kconfig | 7 ++++++- drivers/usb/gadget/pch_udc.c | 7 +++++++ 2 files changed, 13 insertions(+), 1 deletion(-) diff --git a/drivers/usb/gadget/Kconfig b/drivers/usb/gadget/Kconfig index 1dc9739277b4..06bb9d4587e9 100644 --- a/drivers/usb/gadget/Kconfig +++ b/drivers/usb/gadget/Kconfig @@ -509,7 +509,7 @@ config USB_LANGWELL select USB_GADGET_SELECTED config USB_GADGET_EG20T - boolean "Intel EG20T(Topcliff) USB Device controller" + boolean "Intel EG20T PCH/OKI SEMICONDUCTOR ML7213 IOH UDC" depends on PCI select USB_GADGET_DUALSPEED help @@ -525,6 +525,11 @@ config USB_GADGET_EG20T This driver dose not support interrupt transfer or isochronous transfer modes. + This driver also can be used for OKI SEMICONDUCTOR's ML7213 which is + for IVI(In-Vehicle Infotainment) use. + ML7213 is companion chip for Intel Atom E6xx series. + ML7213 is completely compatible for Intel EG20T PCH. + config USB_EG20T tristate depends on USB_GADGET_EG20T diff --git a/drivers/usb/gadget/pch_udc.c b/drivers/usb/gadget/pch_udc.c index dfe927b01ffb..cf0e6da724a9 100644 --- a/drivers/usb/gadget/pch_udc.c +++ b/drivers/usb/gadget/pch_udc.c @@ -361,6 +361,8 @@ struct pch_udc_dev { #define PCH_UDC_PCI_BAR 1 #define PCI_DEVICE_ID_INTEL_EG20T_UDC 0x8808 +#define PCI_VENDOR_ID_ROHM 0x10DB +#define PCI_DEVICE_ID_ML7213_IOH_UDC 0x801D static const char ep0_string[] = "ep0in"; static DEFINE_SPINLOCK(udc_stall_spinlock); /* stall spin lock */ @@ -2931,6 +2933,11 @@ static DEFINE_PCI_DEVICE_TABLE(pch_udc_pcidev_id) = { .class = (PCI_CLASS_SERIAL_USB << 8) | 0xfe, .class_mask = 0xffffffff, }, + { + PCI_DEVICE(PCI_VENDOR_ID_ROHM, PCI_DEVICE_ID_ML7213_IOH_UDC), + .class = (PCI_CLASS_SERIAL_USB << 8) | 0xfe, + .class_mask = 0xffffffff, + }, { 0 }, }; -- cgit v1.2.1 From f75593ceaa08e6d27aec1a5de31cded19e850dd1 Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Thu, 6 Jan 2011 10:17:09 -0500 Subject: USB: EHCI: fix DMA deallocation bug This patch (as1440) fixes a bug in ehci-hcd. ehci->periodic_size is used to compute the size in a dma_alloc_coherent() call, but then it gets changed later on. As a result, the corresponding call to dma_free_coherent() passes a different size from the original allocation. Fix the problem by adjusting ehci->periodic_size before carrying out any of the memory allocations. Signed-off-by: Alan Stern Tested-by: Larry Finger CC: David Brownell CC: Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-hcd.c | 19 ++++++++++++------- 1 file changed, 12 insertions(+), 7 deletions(-) diff --git a/drivers/usb/host/ehci-hcd.c b/drivers/usb/host/ehci-hcd.c index 6fee3cd58efe..74dcf49bd015 100644 --- a/drivers/usb/host/ehci-hcd.c +++ b/drivers/usb/host/ehci-hcd.c @@ -572,6 +572,8 @@ static int ehci_init(struct usb_hcd *hcd) ehci->iaa_watchdog.function = ehci_iaa_watchdog; ehci->iaa_watchdog.data = (unsigned long) ehci; + hcc_params = ehci_readl(ehci, &ehci->caps->hcc_params); + /* * hw default: 1K periodic list heads, one per frame. * periodic_size can shrink by USBCMD update if hcc_params allows. @@ -579,11 +581,20 @@ static int ehci_init(struct usb_hcd *hcd) ehci->periodic_size = DEFAULT_I_TDPS; INIT_LIST_HEAD(&ehci->cached_itd_list); INIT_LIST_HEAD(&ehci->cached_sitd_list); + + if (HCC_PGM_FRAMELISTLEN(hcc_params)) { + /* periodic schedule size can be smaller than default */ + switch (EHCI_TUNE_FLS) { + case 0: ehci->periodic_size = 1024; break; + case 1: ehci->periodic_size = 512; break; + case 2: ehci->periodic_size = 256; break; + default: BUG(); + } + } if ((retval = ehci_mem_init(ehci, GFP_KERNEL)) < 0) return retval; /* controllers may cache some of the periodic schedule ... */ - hcc_params = ehci_readl(ehci, &ehci->caps->hcc_params); if (HCC_ISOC_CACHE(hcc_params)) // full frame cache ehci->i_thresh = 2 + 8; else // N microframes cached @@ -637,12 +648,6 @@ static int ehci_init(struct usb_hcd *hcd) /* periodic schedule size can be smaller than default */ temp &= ~(3 << 2); temp |= (EHCI_TUNE_FLS << 2); - switch (EHCI_TUNE_FLS) { - case 0: ehci->periodic_size = 1024; break; - case 1: ehci->periodic_size = 512; break; - case 2: ehci->periodic_size = 256; break; - default: BUG(); - } } if (HCC_LPM(hcc_params)) { /* support link power management EHCI 1.1 addendum */ -- cgit v1.2.1 From 65519263df87acf09992675304a654d6874f73fd Mon Sep 17 00:00:00 2001 From: Stanislaw Gruszka Date: Sat, 8 Jan 2011 15:19:40 +0100 Subject: MAINTAINERS: add ueagle-atm entry Cc: Matthieu Castet Signed-off-by: Stanislaw Gruszka Signed-off-by: Greg Kroah-Hartman --- MAINTAINERS | 6 ++++++ 1 file changed, 6 insertions(+) diff --git a/MAINTAINERS b/MAINTAINERS index 55592f8b672c..df77a5b2c36c 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -3139,6 +3139,12 @@ S: Maintained F: net/ieee802154/ F: drivers/ieee802154/ +IKANOS/ADI EAGLE ADSL USB DRIVER +M: Matthieu Castet +M: Stanislaw Gruszka +S: Maintained +F: drivers/usb/atm/ueagle-atm.c + INTEGRITY MEASUREMENT ARCHITECTURE (IMA) M: Mimi Zohar S: Supported -- cgit v1.2.1 From bbfba05283ba482ab7c119150fd3c5611939f9fd Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Sat, 8 Jan 2011 18:30:30 +0300 Subject: USB: uss720: remove duplicate USB device Commit ecc1624a2fff45780959efbcb73ace18fdb3c58d (USB: misc: uss720.c: add another vendor/product ID) duplicated entry in the driver's USB device ID table. Remove the duplicate. Signed-off-by: Sergei Shtylyov Signed-off-by: Greg Kroah-Hartman --- drivers/usb/misc/uss720.c | 1 - 1 file changed, 1 deletion(-) diff --git a/drivers/usb/misc/uss720.c b/drivers/usb/misc/uss720.c index 4ff21587ab03..f7a205738032 100644 --- a/drivers/usb/misc/uss720.c +++ b/drivers/usb/misc/uss720.c @@ -776,7 +776,6 @@ static const struct usb_device_id uss720_table[] = { { USB_DEVICE(0x0557, 0x2001) }, { USB_DEVICE(0x0729, 0x1284) }, { USB_DEVICE(0x1293, 0x0002) }, - { USB_DEVICE(0x1293, 0x0002) }, { USB_DEVICE(0x050d, 0x0002) }, { } /* Terminating entry */ }; -- cgit v1.2.1 From d5aa475180d03d45c5dc6134aa833f1b3e89c45e Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Mon, 10 Jan 2011 11:23:05 -0500 Subject: USB: g_printer: fix bug in unregistration This patch (as1441) fixes a bug in g_printer. The gadget driver, char device number, and class device should be unregistered in reverse order of registration. As it is now, when the module is unloaded the class device gets unregistered first, causing a crash when the unbind method tries to access it. This fixes Bugzilla #25882. Signed-off-by: Alan Stern CC: Roland Kletzing CC: Craig W. Nadler CC: Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/printer.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) diff --git a/drivers/usb/gadget/printer.c b/drivers/usb/gadget/printer.c index 2fc8636316c5..dacc67724fe1 100644 --- a/drivers/usb/gadget/printer.c +++ b/drivers/usb/gadget/printer.c @@ -1596,13 +1596,12 @@ cleanup(void) int status; mutex_lock(&usb_printer_gadget.lock_printer_io); - class_destroy(usb_gadget_class); - unregister_chrdev_region(g_printer_devno, 2); - status = usb_gadget_unregister_driver(&printer_driver); if (status) ERROR(dev, "usb_gadget_unregister_driver %x\n", status); + unregister_chrdev_region(g_printer_devno, 2); + class_destroy(usb_gadget_class); mutex_unlock(&usb_printer_gadget.lock_printer_io); } module_exit(cleanup); -- cgit v1.2.1 From ad84e4a9efb7c8ed322bafb6ebdb9c3a49a3d3a8 Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Mon, 10 Jan 2011 11:24:14 -0500 Subject: USB: g_printer: fix bug in module parameter definitions This patch (as1442) fixes a bug in g_printer: Module parameters should not be marked "__initdata" if they are accessible in sysfs (i.e., if the mode value in the module_param() macro is nonzero). Otherwise attempts to access the parameters will cause addressing violations. Character-string module parameters must not be marked "__initdata" if the module can be unloaded, because the kernel needs to access the parameter variable at unload time in order to free the dynamically-allocated string. Signed-off-by: Alan Stern CC: Roland Kletzing CC: Craig W. Nadler CC: Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/printer.c | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) diff --git a/drivers/usb/gadget/printer.c b/drivers/usb/gadget/printer.c index dacc67724fe1..12ff6cffedc9 100644 --- a/drivers/usb/gadget/printer.c +++ b/drivers/usb/gadget/printer.c @@ -131,31 +131,31 @@ static struct printer_dev usb_printer_gadget; * parameters are in UTF-8 (superset of ASCII's 7 bit characters). */ -static ushort __initdata idVendor; +static ushort idVendor; module_param(idVendor, ushort, S_IRUGO); MODULE_PARM_DESC(idVendor, "USB Vendor ID"); -static ushort __initdata idProduct; +static ushort idProduct; module_param(idProduct, ushort, S_IRUGO); MODULE_PARM_DESC(idProduct, "USB Product ID"); -static ushort __initdata bcdDevice; +static ushort bcdDevice; module_param(bcdDevice, ushort, S_IRUGO); MODULE_PARM_DESC(bcdDevice, "USB Device version (BCD)"); -static char *__initdata iManufacturer; +static char *iManufacturer; module_param(iManufacturer, charp, S_IRUGO); MODULE_PARM_DESC(iManufacturer, "USB Manufacturer string"); -static char *__initdata iProduct; +static char *iProduct; module_param(iProduct, charp, S_IRUGO); MODULE_PARM_DESC(iProduct, "USB Product string"); -static char *__initdata iSerialNum; +static char *iSerialNum; module_param(iSerialNum, charp, S_IRUGO); MODULE_PARM_DESC(iSerialNum, "1"); -static char *__initdata iPNPstring; +static char *iPNPstring; module_param(iPNPstring, charp, S_IRUGO); MODULE_PARM_DESC(iPNPstring, "MFG:linux;MDL:g_printer;CLS:PRINTER;SN:1;"); -- cgit v1.2.1 From cc604ddd118cf4a699c12bc41a5fa2d2f225f702 Mon Sep 17 00:00:00 2001 From: Peter Tyser Date: Mon, 10 Jan 2011 17:34:14 -0600 Subject: USB: ehci-fsl: Fix 'have_sysif_regs' detection Previously a check was done on an ID register at the base of a CPU's internal USB registers to determine if system interface regsiters were present. The check looked for an ID register that had the format ID[0:5] == ~ID[8:13] as described in the MPC5121 User's Manual to determine if a MPC5121 or MPC83xx/85xx was being used. There are two issues with this method: - The ID register is not defined on the MPC83xx/85xx CPUs, so its unclear what is being checked on them. - Newer CPUs such as the P4080 also don't document the ID register, but do share the same format as the MPC5121. Thus the previous code did not set 'have_sysif_regs' properly which results in the P4080 not properly initializing its USB ports. Using the device tree 'compatible' node is a cleaner way to determine if 'have_sysif_regs' should be set and resolves the USB initialization issue seen on the P4080. Tested on a P4080-based system and compile tested on mpc512x_defconfig with Freescale EHCI driver enabled. Cc: Anatolij Gustschin Cc: David Brownell Cc: Kumar Gala Cc: linuxppc-dev@lists.ozlabs.org Signed-off-by: Peter Tyser Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-fsl.c | 13 ------------- drivers/usb/host/ehci-fsl.h | 3 --- drivers/usb/host/fsl-mph-dr-of.c | 11 ++++++++--- 3 files changed, 8 insertions(+), 19 deletions(-) diff --git a/drivers/usb/host/ehci-fsl.c b/drivers/usb/host/ehci-fsl.c index 86e42892016d..5c761df7fa83 100644 --- a/drivers/usb/host/ehci-fsl.c +++ b/drivers/usb/host/ehci-fsl.c @@ -52,7 +52,6 @@ static int usb_hcd_fsl_probe(const struct hc_driver *driver, struct resource *res; int irq; int retval; - unsigned int temp; pr_debug("initializing FSL-SOC USB Controller\n"); @@ -126,18 +125,6 @@ static int usb_hcd_fsl_probe(const struct hc_driver *driver, goto err3; } - /* - * Check if it is MPC5121 SoC, otherwise set pdata->have_sysif_regs - * flag for 83xx or 8536 system interface registers. - */ - if (pdata->big_endian_mmio) - temp = in_be32(hcd->regs + FSL_SOC_USB_ID); - else - temp = in_le32(hcd->regs + FSL_SOC_USB_ID); - - if ((temp & ID_MSK) != (~((temp & NID_MSK) >> 8) & ID_MSK)) - pdata->have_sysif_regs = 1; - /* Enable USB controller, 83xx or 8536 */ if (pdata->have_sysif_regs) setbits32(hcd->regs + FSL_SOC_USB_CTRL, 0x4); diff --git a/drivers/usb/host/ehci-fsl.h b/drivers/usb/host/ehci-fsl.h index 2c8353795226..3fabed33d940 100644 --- a/drivers/usb/host/ehci-fsl.h +++ b/drivers/usb/host/ehci-fsl.h @@ -19,9 +19,6 @@ #define _EHCI_FSL_H /* offsets for the non-ehci registers in the FSL SOC USB controller */ -#define FSL_SOC_USB_ID 0x0 -#define ID_MSK 0x3f -#define NID_MSK 0x3f00 #define FSL_SOC_USB_ULPIVP 0x170 #define FSL_SOC_USB_PORTSC1 0x184 #define PORT_PTS_MSK (3<<30) diff --git a/drivers/usb/host/fsl-mph-dr-of.c b/drivers/usb/host/fsl-mph-dr-of.c index 574b99ea0700..79a66d622f9c 100644 --- a/drivers/usb/host/fsl-mph-dr-of.c +++ b/drivers/usb/host/fsl-mph-dr-of.c @@ -262,19 +262,24 @@ static void fsl_usb2_mpc5121_exit(struct platform_device *pdev) } } -struct fsl_usb2_platform_data fsl_usb2_mpc5121_pd = { +static struct fsl_usb2_platform_data fsl_usb2_mpc5121_pd = { .big_endian_desc = 1, .big_endian_mmio = 1, .es = 1, + .have_sysif_regs = 0, .le_setup_buf = 1, .init = fsl_usb2_mpc5121_init, .exit = fsl_usb2_mpc5121_exit, }; #endif /* CONFIG_PPC_MPC512x */ +static struct fsl_usb2_platform_data fsl_usb2_mpc8xxx_pd = { + .have_sysif_regs = 1, +}; + static const struct of_device_id fsl_usb2_mph_dr_of_match[] = { - { .compatible = "fsl-usb2-mph", }, - { .compatible = "fsl-usb2-dr", }, + { .compatible = "fsl-usb2-mph", .data = &fsl_usb2_mpc8xxx_pd, }, + { .compatible = "fsl-usb2-dr", .data = &fsl_usb2_mpc8xxx_pd, }, #ifdef CONFIG_PPC_MPC512x { .compatible = "fsl,mpc5121-usb2-dr", .data = &fsl_usb2_mpc5121_pd, }, #endif -- cgit v1.2.1 From 5620b5f7f19e9ee3fcf6ecf493fed7821b7b495b Mon Sep 17 00:00:00 2001 From: Alan Stern Date: Tue, 11 Jan 2011 14:16:50 -0500 Subject: USB serial: add missing .usb_driver field in serial drivers This patch (as1443) fixes a bug found in many of the USB serial drivers: They don't set the .usb_driver field in their usb_serial_driver structure. This field is needed for assigning dynamic IDs for device matching. In addition, starting with the 2.6.37 kernel, the .usb_driver field is needed for proper autosuspend operation. Without it, attempts to open the device file will fail. Signed-off-by: Alan Stern Reported-by: Dan Williams CC: Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/io_tables.h | 1 + drivers/usb/serial/iuu_phoenix.c | 1 + drivers/usb/serial/keyspan.h | 4 ++++ drivers/usb/serial/moto_modem.c | 1 + drivers/usb/serial/oti6858.c | 1 + drivers/usb/serial/qcaux.c | 1 + drivers/usb/serial/siemens_mpi.c | 1 + drivers/usb/serial/spcp8x5.c | 1 + drivers/usb/serial/usb-serial.c | 8 ++++++-- drivers/usb/serial/usb_debug.c | 1 + 10 files changed, 18 insertions(+), 2 deletions(-) diff --git a/drivers/usb/serial/io_tables.h b/drivers/usb/serial/io_tables.h index 6ab2a3f97fe8..178b22eb32b1 100644 --- a/drivers/usb/serial/io_tables.h +++ b/drivers/usb/serial/io_tables.h @@ -199,6 +199,7 @@ static struct usb_serial_driver epic_device = { .name = "epic", }, .description = "EPiC device", + .usb_driver = &io_driver, .id_table = Epic_port_id_table, .num_ports = 1, .open = edge_open, diff --git a/drivers/usb/serial/iuu_phoenix.c b/drivers/usb/serial/iuu_phoenix.c index 12ed594f5f80..99b97c04896f 100644 --- a/drivers/usb/serial/iuu_phoenix.c +++ b/drivers/usb/serial/iuu_phoenix.c @@ -1275,6 +1275,7 @@ static struct usb_serial_driver iuu_device = { .name = "iuu_phoenix", }, .id_table = id_table, + .usb_driver = &iuu_driver, .num_ports = 1, .bulk_in_size = 512, .bulk_out_size = 512, diff --git a/drivers/usb/serial/keyspan.h b/drivers/usb/serial/keyspan.h index 2d8baf6ac472..ce134dc28ddf 100644 --- a/drivers/usb/serial/keyspan.h +++ b/drivers/usb/serial/keyspan.h @@ -546,6 +546,7 @@ static struct usb_serial_driver keyspan_pre_device = { .name = "keyspan_no_firm", }, .description = "Keyspan - (without firmware)", + .usb_driver = &keyspan_driver, .id_table = keyspan_pre_ids, .num_ports = 1, .attach = keyspan_fake_startup, @@ -557,6 +558,7 @@ static struct usb_serial_driver keyspan_1port_device = { .name = "keyspan_1", }, .description = "Keyspan 1 port adapter", + .usb_driver = &keyspan_driver, .id_table = keyspan_1port_ids, .num_ports = 1, .open = keyspan_open, @@ -579,6 +581,7 @@ static struct usb_serial_driver keyspan_2port_device = { .name = "keyspan_2", }, .description = "Keyspan 2 port adapter", + .usb_driver = &keyspan_driver, .id_table = keyspan_2port_ids, .num_ports = 2, .open = keyspan_open, @@ -601,6 +604,7 @@ static struct usb_serial_driver keyspan_4port_device = { .name = "keyspan_4", }, .description = "Keyspan 4 port adapter", + .usb_driver = &keyspan_driver, .id_table = keyspan_4port_ids, .num_ports = 4, .open = keyspan_open, diff --git a/drivers/usb/serial/moto_modem.c b/drivers/usb/serial/moto_modem.c index cf1718394e18..653465f61d4a 100644 --- a/drivers/usb/serial/moto_modem.c +++ b/drivers/usb/serial/moto_modem.c @@ -44,6 +44,7 @@ static struct usb_serial_driver moto_device = { .name = "moto-modem", }, .id_table = id_table, + .usb_driver = &moto_driver, .num_ports = 1, }; diff --git a/drivers/usb/serial/oti6858.c b/drivers/usb/serial/oti6858.c index 5be866bb7a41..73613205be7a 100644 --- a/drivers/usb/serial/oti6858.c +++ b/drivers/usb/serial/oti6858.c @@ -157,6 +157,7 @@ static struct usb_serial_driver oti6858_device = { .name = "oti6858", }, .id_table = id_table, + .usb_driver = &oti6858_driver, .num_ports = 1, .open = oti6858_open, .close = oti6858_close, diff --git a/drivers/usb/serial/qcaux.c b/drivers/usb/serial/qcaux.c index b53865b8cd9c..30b73e68a904 100644 --- a/drivers/usb/serial/qcaux.c +++ b/drivers/usb/serial/qcaux.c @@ -86,6 +86,7 @@ static struct usb_serial_driver qcaux_device = { .name = "qcaux", }, .id_table = id_table, + .usb_driver = &qcaux_driver, .num_ports = 1, }; diff --git a/drivers/usb/serial/siemens_mpi.c b/drivers/usb/serial/siemens_mpi.c index cb8195cabfde..74cd4ccdb3fc 100644 --- a/drivers/usb/serial/siemens_mpi.c +++ b/drivers/usb/serial/siemens_mpi.c @@ -42,6 +42,7 @@ static struct usb_serial_driver siemens_usb_mpi_device = { .name = "siemens_mpi", }, .id_table = id_table, + .usb_driver = &siemens_usb_mpi_driver, .num_ports = 1, }; diff --git a/drivers/usb/serial/spcp8x5.c b/drivers/usb/serial/spcp8x5.c index 765aa983bf58..c7665d39d192 100644 --- a/drivers/usb/serial/spcp8x5.c +++ b/drivers/usb/serial/spcp8x5.c @@ -645,6 +645,7 @@ static struct usb_serial_driver spcp8x5_device = { .name = "SPCP8x5", }, .id_table = id_table, + .usb_driver = &spcp8x5_driver, .num_ports = 1, .open = spcp8x5_open, .dtr_rts = spcp8x5_dtr_rts, diff --git a/drivers/usb/serial/usb-serial.c b/drivers/usb/serial/usb-serial.c index 6954de50c0ff..546a52179bec 100644 --- a/drivers/usb/serial/usb-serial.c +++ b/drivers/usb/serial/usb-serial.c @@ -1344,11 +1344,15 @@ int usb_serial_register(struct usb_serial_driver *driver) return -ENODEV; fixup_generic(driver); - if (driver->usb_driver) - driver->usb_driver->supports_autosuspend = 1; if (!driver->description) driver->description = driver->driver.name; + if (!driver->usb_driver) { + WARN(1, "Serial driver %s has no usb_driver\n", + driver->description); + return -EINVAL; + } + driver->usb_driver->supports_autosuspend = 1; /* Add this device to our list of devices */ mutex_lock(&table_lock); diff --git a/drivers/usb/serial/usb_debug.c b/drivers/usb/serial/usb_debug.c index f2ed6a31be77..95a82148ee81 100644 --- a/drivers/usb/serial/usb_debug.c +++ b/drivers/usb/serial/usb_debug.c @@ -75,6 +75,7 @@ static struct usb_serial_driver debug_device = { .name = "debug", }, .id_table = id_table, + .usb_driver = &debug_driver, .num_ports = 1, .bulk_out_size = USB_DEBUG_MAX_PACKET_SIZE, .break_ctl = usb_debug_break_ctl, -- cgit v1.2.1 From aa52b3a92918039b273fc9d1994bd34227c40269 Mon Sep 17 00:00:00 2001 From: Nicolaus Colberg Date: Wed, 12 Jan 2011 16:30:03 +0100 Subject: USB: adding USB support for Cinterion's HC2x, EU3 and PH8 products /drivers/usb/serial/option.c: Adding support for Cinterion's HC25, HC28, HC28J, EU3-E, EU3-P and PH8 by correcting/adding Cinterion's and Siemens' Vendor IDs as well as Product IDs and USB_DEVICE tuples Signed-off-by: Nicolaus Colberg Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/option.c | 23 +++++++++++++++++++++-- 1 file changed, 21 insertions(+), 2 deletions(-) diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c index 748778288d94..5f46838dfee5 100644 --- a/drivers/usb/serial/option.c +++ b/drivers/usb/serial/option.c @@ -382,7 +382,16 @@ static void option_instat_callback(struct urb *urb); #define HAIER_VENDOR_ID 0x201e #define HAIER_PRODUCT_CE100 0x2009 -#define CINTERION_VENDOR_ID 0x0681 +/* Cinterion (formerly Siemens) products */ +#define SIEMENS_VENDOR_ID 0x0681 +#define CINTERION_VENDOR_ID 0x1e2d +#define CINTERION_PRODUCT_HC25_MDM 0x0047 +#define CINTERION_PRODUCT_HC25_MDMNET 0x0040 +#define CINTERION_PRODUCT_HC28_MDM 0x004C +#define CINTERION_PRODUCT_HC28_MDMNET 0x004A /* same for HC28J */ +#define CINTERION_PRODUCT_EU3_E 0x0051 +#define CINTERION_PRODUCT_EU3_P 0x0052 +#define CINTERION_PRODUCT_PH8 0x0053 /* Olivetti products */ #define OLIVETTI_VENDOR_ID 0x0b3c @@ -944,7 +953,17 @@ static const struct usb_device_id option_ids[] = { { USB_DEVICE(PIRELLI_VENDOR_ID, PIRELLI_PRODUCT_100F) }, { USB_DEVICE(PIRELLI_VENDOR_ID, PIRELLI_PRODUCT_1011)}, { USB_DEVICE(PIRELLI_VENDOR_ID, PIRELLI_PRODUCT_1012)}, - { USB_DEVICE(CINTERION_VENDOR_ID, 0x0047) }, + /* Cinterion */ + { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_EU3_E) }, + { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_EU3_P) }, + { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_PH8) }, + { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_HC28_MDM) }, + { USB_DEVICE(CINTERION_VENDOR_ID, CINTERION_PRODUCT_HC28_MDMNET) }, + { USB_DEVICE(SIEMENS_VENDOR_ID, CINTERION_PRODUCT_HC25_MDM) }, + { USB_DEVICE(SIEMENS_VENDOR_ID, CINTERION_PRODUCT_HC25_MDMNET) }, + { USB_DEVICE(SIEMENS_VENDOR_ID, CINTERION_PRODUCT_HC28_MDM) }, /* HC28 enumerates with Siemens or Cinterion VID depending on FW revision */ + { USB_DEVICE(SIEMENS_VENDOR_ID, CINTERION_PRODUCT_HC28_MDMNET) }, + { USB_DEVICE(OLIVETTI_VENDOR_ID, OLIVETTI_PRODUCT_OLICARD100) }, { USB_DEVICE(CELOT_VENDOR_ID, CELOT_PRODUCT_CT680M) }, /* CT-650 CDMA 450 1xEVDO modem */ { USB_DEVICE(ONDA_VENDOR_ID, ONDA_MT825UP) }, /* ONDA MT825UP modem */ -- cgit v1.2.1 From 96a3e79edff6f41b0f115a82f1a39d66218077a7 Mon Sep 17 00:00:00 2001 From: Dario Lombardo Date: Fri, 21 Jan 2011 15:35:19 +0100 Subject: drivers: update to pl2303 usb-serial to support Motorola cables Added 0x0307 device id to support Motorola cables to the pl2303 usb serial driver. This cable has a modified chip that is a pl2303, but declares itself as 0307. Fixed by adding the right device id to the supported devices list, assigning it the code labeled PL2303_PRODUCT_ID_MOTOROLA. Signed-off-by: Dario Lombardo Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/pl2303.c | 1 + drivers/usb/serial/pl2303.h | 1 + 2 files changed, 2 insertions(+) diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c index 8ae4c6cbc38a..45c40e6e9737 100644 --- a/drivers/usb/serial/pl2303.c +++ b/drivers/usb/serial/pl2303.c @@ -50,6 +50,7 @@ static const struct usb_device_id id_table[] = { { USB_DEVICE(PL2303_VENDOR_ID, PL2303_PRODUCT_ID_MMX) }, { USB_DEVICE(PL2303_VENDOR_ID, PL2303_PRODUCT_ID_GPRS) }, { USB_DEVICE(PL2303_VENDOR_ID, PL2303_PRODUCT_ID_HCR331) }, + { USB_DEVICE(PL2303_VENDOR_ID, PL2303_PRODUCT_ID_MOTOROLA) }, { USB_DEVICE(IODATA_VENDOR_ID, IODATA_PRODUCT_ID) }, { USB_DEVICE(IODATA_VENDOR_ID, IODATA_PRODUCT_ID_RSAQ5) }, { USB_DEVICE(ATEN_VENDOR_ID, ATEN_PRODUCT_ID) }, diff --git a/drivers/usb/serial/pl2303.h b/drivers/usb/serial/pl2303.h index 43eb9bdad422..1b025f75dafd 100644 --- a/drivers/usb/serial/pl2303.h +++ b/drivers/usb/serial/pl2303.h @@ -21,6 +21,7 @@ #define PL2303_PRODUCT_ID_MMX 0x0612 #define PL2303_PRODUCT_ID_GPRS 0x0609 #define PL2303_PRODUCT_ID_HCR331 0x331a +#define PL2303_PRODUCT_ID_MOTOROLA 0x0307 #define ATEN_VENDOR_ID 0x0557 #define ATEN_VENDOR_ID2 0x0547 -- cgit v1.2.1 From 3bb8029a2445e289efade6133b01545143336f70 Mon Sep 17 00:00:00 2001 From: =?UTF-8?q?Eric=20B=C3=A9nard?= Date: Thu, 13 Jan 2011 14:53:17 +0100 Subject: USB: unbreak ehci-mxc on otg port of i.MX27 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit commit 711669e5b80b6f2d88f61ed8a9681f83d8cbd201 fixed port 0 support for i.MX51 but broke it for (at least) i.MX27 which doesn't have a usb_phy1 clock but has a pdev->id 0. Signed-off-by: Eric Bénard Cc: Arnaud Patard Cc: Sascha Hauer Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-mxc.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/usb/host/ehci-mxc.c b/drivers/usb/host/ehci-mxc.c index fa59b26fc5bc..d443fbd8535b 100644 --- a/drivers/usb/host/ehci-mxc.c +++ b/drivers/usb/host/ehci-mxc.c @@ -177,8 +177,8 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev) clk_enable(priv->ahbclk); } - /* "dr" device has its own clock */ - if (pdev->id == 0) { + /* "dr" device has its own clock on i.MX51 */ + if (cpu_is_mx51() && (pdev->id == 0)) { priv->phy1clk = clk_get(dev, "usb_phy1"); if (IS_ERR(priv->phy1clk)) { ret = PTR_ERR(priv->phy1clk); -- cgit v1.2.1 From a464dc4d4044c936d4558725fa2229fb4a1aa932 Mon Sep 17 00:00:00 2001 From: "Arnaud Patard (Rtp)" Date: Tue, 18 Jan 2011 00:04:12 +0100 Subject: USB: ehci-mxc: add work-around for efika mx/sb bug Add support for setting CHRGVBUS to workaround a hardware bug on efika mx/sb boards. See http://lists.infradead.org/pipermail/linux-arm-kernel/2011-January/037341.html Signed-off-by: Arnaud Patard Signed-off-by: Greg Kroah-Hartman --- drivers/usb/host/ehci-mxc.c | 21 +++++++++++++++++++++ 1 file changed, 21 insertions(+) diff --git a/drivers/usb/host/ehci-mxc.c b/drivers/usb/host/ehci-mxc.c index d443fbd8535b..c8e360d7d975 100644 --- a/drivers/usb/host/ehci-mxc.c +++ b/drivers/usb/host/ehci-mxc.c @@ -21,10 +21,13 @@ #include #include #include +#include #include #include +#include + #define ULPI_VIEWPORT_OFFSET 0x170 struct ehci_mxc_priv { @@ -114,6 +117,7 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev) struct usb_hcd *hcd; struct resource *res; int irq, ret; + unsigned int flags; struct ehci_mxc_priv *priv; struct device *dev = &pdev->dev; struct ehci_hcd *ehci; @@ -240,6 +244,23 @@ static int ehci_mxc_drv_probe(struct platform_device *pdev) if (ret) goto err_add; + if (pdata->otg) { + /* + * efikamx and efikasb have some hardware bug which is + * preventing usb to work unless CHRGVBUS is set. + * It's in violation of USB specs + */ + if (machine_is_mx51_efikamx() || machine_is_mx51_efikasb()) { + flags = otg_io_read(pdata->otg, ULPI_OTG_CTRL); + flags |= ULPI_OTG_CTRL_CHRGVBUS; + ret = otg_io_write(pdata->otg, flags, ULPI_OTG_CTRL); + if (ret) { + dev_err(dev, "unable to set CHRVBUS\n"); + goto err_add; + } + } + } + return 0; err_add: -- cgit v1.2.1 From a9d61bc49188e32d2ae9cf0f683cde3e1744feef Mon Sep 17 00:00:00 2001 From: Pieter Maes Date: Tue, 18 Jan 2011 00:26:16 +0100 Subject: USB: serial: Updated support for ICOM devices I found the original patch on the db0fhn repeater wiki (couldn't find the email of the origial author) I guess it was never commited. I updated and added some Icom HAM-radio devices to the ftdi driver. Added extra comments to make clear what devices it are. Signed-off-by: Pieter Maes Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ftdi_sio.c | 12 +++++++++++- drivers/usb/serial/ftdi_sio_ids.h | 22 +++++++++++++++++----- 2 files changed, 28 insertions(+), 6 deletions(-) diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c index a2668d089260..4787c0cd063f 100644 --- a/drivers/usb/serial/ftdi_sio.c +++ b/drivers/usb/serial/ftdi_sio.c @@ -676,7 +676,17 @@ static struct usb_device_id id_table_combined [] = { { USB_DEVICE(FTDI_VID, FTDI_PCDJ_DAC2_PID) }, { USB_DEVICE(FTDI_VID, FTDI_RRCIRKITS_LOCOBUFFER_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ASK_RDR400_PID) }, - { USB_DEVICE(ICOM_ID1_VID, ICOM_ID1_PID) }, + { USB_DEVICE(ICOM_VID, ICOM_ID_1_PID) }, + { USB_DEVICE(ICOM_VID, ICOM_OPC_U_UC_PID) }, + { USB_DEVICE(ICOM_VID, ICOM_ID_RP2C1_PID) }, + { USB_DEVICE(ICOM_VID, ICOM_ID_RP2C2_PID) }, + { USB_DEVICE(ICOM_VID, ICOM_ID_RP2D_PID) }, + { USB_DEVICE(ICOM_VID, ICOM_ID_RP2VT_PID) }, + { USB_DEVICE(ICOM_VID, ICOM_ID_RP2VR_PID) }, + { USB_DEVICE(ICOM_VID, ICOM_ID_RP4KVT_PID) }, + { USB_DEVICE(ICOM_VID, ICOM_ID_RP4KVR_PID) }, + { USB_DEVICE(ICOM_VID, ICOM_ID_RP2KVT_PID) }, + { USB_DEVICE(ICOM_VID, ICOM_ID_RP2KVR_PID) }, { USB_DEVICE(FTDI_VID, FTDI_ACG_HFDUAL_PID) }, { USB_DEVICE(FTDI_VID, FTDI_YEI_SERVOCENTER31_PID) }, { USB_DEVICE(FTDI_VID, FTDI_THORLABS_PID) }, diff --git a/drivers/usb/serial/ftdi_sio_ids.h b/drivers/usb/serial/ftdi_sio_ids.h index bf0867285481..ed160def8584 100644 --- a/drivers/usb/serial/ftdi_sio_ids.h +++ b/drivers/usb/serial/ftdi_sio_ids.h @@ -569,11 +569,23 @@ #define OCT_US101_PID 0x0421 /* OCT US101 USB to RS-232 */ /* - * Icom ID-1 digital transceiver - */ - -#define ICOM_ID1_VID 0x0C26 -#define ICOM_ID1_PID 0x0004 + * Definitions for Icom Inc. devices + */ +#define ICOM_VID 0x0C26 /* Icom vendor ID */ +/* Note: ID-1 is a communications tranceiver for HAM-radio operators */ +#define ICOM_ID_1_PID 0x0004 /* ID-1 USB to RS-232 */ +/* Note: OPC is an Optional cable to connect an Icom Tranceiver */ +#define ICOM_OPC_U_UC_PID 0x0018 /* OPC-478UC, OPC-1122U cloning cable */ +/* Note: ID-RP* devices are Icom Repeater Devices for HAM-radio */ +#define ICOM_ID_RP2C1_PID 0x0009 /* ID-RP2C Asset 1 to RS-232 */ +#define ICOM_ID_RP2C2_PID 0x000A /* ID-RP2C Asset 2 to RS-232 */ +#define ICOM_ID_RP2D_PID 0x000B /* ID-RP2D configuration port*/ +#define ICOM_ID_RP2VT_PID 0x000C /* ID-RP2V Transmit config port */ +#define ICOM_ID_RP2VR_PID 0x000D /* ID-RP2V Receive config port */ +#define ICOM_ID_RP4KVT_PID 0x0010 /* ID-RP4000V Transmit config port */ +#define ICOM_ID_RP4KVR_PID 0x0011 /* ID-RP4000V Receive config port */ +#define ICOM_ID_RP2KVT_PID 0x0012 /* ID-RP2000V Transmit config port */ +#define ICOM_ID_RP2KVR_PID 0x0013 /* ID-RP2000V Receive config port */ /* * GN Otometrics (http://www.otometrics.com) -- cgit v1.2.1 From 15680cdfc69a7277ba87a8a3a3242d67c4ba5916 Mon Sep 17 00:00:00 2001 From: Toshiharu Okada Date: Tue, 18 Jan 2011 20:26:27 +0900 Subject: usb: pch_udc: Fix the worning log issue at gadget driver remove When removing a serial gadget driver, the kernel warning message is outputted. This patch fixed this issue. The pch_udc driver did not have disconnection processing of gadget. Signed-off-by: Toshiharu Okada Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/pch_udc.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/usb/gadget/pch_udc.c b/drivers/usb/gadget/pch_udc.c index cf0e6da724a9..b120dbb64d0f 100644 --- a/drivers/usb/gadget/pch_udc.c +++ b/drivers/usb/gadget/pch_udc.c @@ -2718,7 +2718,8 @@ int usb_gadget_unregister_driver(struct usb_gadget_driver *driver) pch_udc_disable_interrupts(dev, UDC_DEVINT_MSK); - /* Assues that there are no pending requets with this driver */ + /* Assures that there are no pending requests with this driver */ + driver->disconnect(&dev->gadget); driver->unbind(&dev->gadget); dev->gadget.dev.driver = NULL; dev->driver = NULL; -- cgit v1.2.1 From 49d3df53a80deed2251b91f50ae9e1c5caf7ded7 Mon Sep 17 00:00:00 2001 From: Pavankumar Kondeti Date: Tue, 11 Jan 2011 09:19:21 +0530 Subject: USB: gadget: Fix error path in ci13xxx_udc gadget probe function Don't call gadget driver's unbind when bind is failed. Initialize udc->driver only after gadget driver bind is successful. Otherwise pull-up can be enabled upon VBUS session even when no gadget is bounded. Signed-off-by: Pavankumar Kondeti Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/ci13xxx_udc.c | 4 +--- 1 file changed, 1 insertion(+), 3 deletions(-) diff --git a/drivers/usb/gadget/ci13xxx_udc.c b/drivers/usb/gadget/ci13xxx_udc.c index 31656a2b4ab4..b0b90621dc1b 100644 --- a/drivers/usb/gadget/ci13xxx_udc.c +++ b/drivers/usb/gadget/ci13xxx_udc.c @@ -2427,7 +2427,6 @@ int usb_gadget_probe_driver(struct usb_gadget_driver *driver, info("hw_ep_max = %d", hw_ep_max); - udc->driver = driver; udc->gadget.dev.driver = NULL; retval = 0; @@ -2479,6 +2478,7 @@ int usb_gadget_probe_driver(struct usb_gadget_driver *driver, goto done; } + udc->driver = driver; pm_runtime_get_sync(&udc->gadget.dev); if (udc->udc_driver->flags & CI13XXX_PULLUP_ON_VBUS) { if (udc->vbus_active) { @@ -2496,8 +2496,6 @@ int usb_gadget_probe_driver(struct usb_gadget_driver *driver, done: spin_unlock_irqrestore(udc->lock, flags); - if (retval) - usb_gadget_unregister_driver(driver); return retval; } EXPORT_SYMBOL(usb_gadget_probe_driver); -- cgit v1.2.1 From ca9cfea09fc5802074f79d086547c6363ddc894b Mon Sep 17 00:00:00 2001 From: Pavankumar Kondeti Date: Tue, 11 Jan 2011 09:19:22 +0530 Subject: USB: gadget: Fix endpoint representation in ci13xxx_udc Fix a bug where only half the number of endpoints supported by the hardware are exposed to gadget. If DEN filed in the DCCPARAMS register has 'N' then 'N' IN endpoints and 'N" OUT endpoints can be supported. But only 'N' bidirectional endpoints are added to the gadget ep_list. This patch also ensures that the data and handshake transactions of previous setup packet are flushed upon a new setup packet arrival on ep0. Signed-off-by: Pavankumar Kondeti Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/ci13xxx_udc.c | 264 ++++++++++++++++++++------------------- drivers/usb/gadget/ci13xxx_udc.h | 9 +- 2 files changed, 142 insertions(+), 131 deletions(-) diff --git a/drivers/usb/gadget/ci13xxx_udc.c b/drivers/usb/gadget/ci13xxx_udc.c index b0b90621dc1b..a1c67ae1572a 100644 --- a/drivers/usb/gadget/ci13xxx_udc.c +++ b/drivers/usb/gadget/ci13xxx_udc.c @@ -76,10 +76,21 @@ static DEFINE_SPINLOCK(udc_lock); /* control endpoint description */ static const struct usb_endpoint_descriptor -ctrl_endpt_desc = { +ctrl_endpt_out_desc = { .bLength = USB_DT_ENDPOINT_SIZE, .bDescriptorType = USB_DT_ENDPOINT, + .bEndpointAddress = USB_DIR_OUT, + .bmAttributes = USB_ENDPOINT_XFER_CONTROL, + .wMaxPacketSize = cpu_to_le16(CTRL_PAYLOAD_MAX), +}; + +static const struct usb_endpoint_descriptor +ctrl_endpt_in_desc = { + .bLength = USB_DT_ENDPOINT_SIZE, + .bDescriptorType = USB_DT_ENDPOINT, + + .bEndpointAddress = USB_DIR_IN, .bmAttributes = USB_ENDPOINT_XFER_CONTROL, .wMaxPacketSize = cpu_to_le16(CTRL_PAYLOAD_MAX), }; @@ -265,10 +276,10 @@ static int hw_device_init(void __iomem *base) hw_bank.size /= sizeof(u32); reg = hw_aread(ABS_DCCPARAMS, DCCPARAMS_DEN) >> ffs_nr(DCCPARAMS_DEN); - if (reg == 0 || reg > ENDPT_MAX) - return -ENODEV; + hw_ep_max = reg * 2; /* cache hw ENDPT_MAX */ - hw_ep_max = reg; /* cache hw ENDPT_MAX */ + if (hw_ep_max == 0 || hw_ep_max > ENDPT_MAX) + return -ENODEV; /* setup lock mode ? */ @@ -1197,16 +1208,17 @@ static ssize_t show_qheads(struct device *dev, struct device_attribute *attr, } spin_lock_irqsave(udc->lock, flags); - for (i = 0; i < hw_ep_max; i++) { - struct ci13xxx_ep *mEp = &udc->ci13xxx_ep[i]; + for (i = 0; i < hw_ep_max/2; i++) { + struct ci13xxx_ep *mEpRx = &udc->ci13xxx_ep[i]; + struct ci13xxx_ep *mEpTx = &udc->ci13xxx_ep[i + hw_ep_max/2]; n += scnprintf(buf + n, PAGE_SIZE - n, "EP=%02i: RX=%08X TX=%08X\n", - i, (u32)mEp->qh[RX].dma, (u32)mEp->qh[TX].dma); + i, (u32)mEpRx->qh.dma, (u32)mEpTx->qh.dma); for (j = 0; j < (sizeof(struct ci13xxx_qh)/sizeof(u32)); j++) { n += scnprintf(buf + n, PAGE_SIZE - n, " %04X: %08X %08X\n", j, - *((u32 *)mEp->qh[RX].ptr + j), - *((u32 *)mEp->qh[TX].ptr + j)); + *((u32 *)mEpRx->qh.ptr + j), + *((u32 *)mEpTx->qh.ptr + j)); } } spin_unlock_irqrestore(udc->lock, flags); @@ -1293,7 +1305,7 @@ static ssize_t show_requests(struct device *dev, struct device_attribute *attr, unsigned long flags; struct list_head *ptr = NULL; struct ci13xxx_req *req = NULL; - unsigned i, j, k, n = 0, qSize = sizeof(struct ci13xxx_td)/sizeof(u32); + unsigned i, j, n = 0, qSize = sizeof(struct ci13xxx_td)/sizeof(u32); dbg_trace("[%s] %p\n", __func__, buf); if (attr == NULL || buf == NULL) { @@ -1303,22 +1315,20 @@ static ssize_t show_requests(struct device *dev, struct device_attribute *attr, spin_lock_irqsave(udc->lock, flags); for (i = 0; i < hw_ep_max; i++) - for (k = RX; k <= TX; k++) - list_for_each(ptr, &udc->ci13xxx_ep[i].qh[k].queue) - { - req = list_entry(ptr, - struct ci13xxx_req, queue); + list_for_each(ptr, &udc->ci13xxx_ep[i].qh.queue) + { + req = list_entry(ptr, struct ci13xxx_req, queue); + n += scnprintf(buf + n, PAGE_SIZE - n, + "EP=%02i: TD=%08X %s\n", + i % hw_ep_max/2, (u32)req->dma, + ((i < hw_ep_max/2) ? "RX" : "TX")); + + for (j = 0; j < qSize; j++) n += scnprintf(buf + n, PAGE_SIZE - n, - "EP=%02i: TD=%08X %s\n", - i, (u32)req->dma, - ((k == RX) ? "RX" : "TX")); - - for (j = 0; j < qSize; j++) - n += scnprintf(buf + n, PAGE_SIZE - n, - " %04X: %08X\n", j, - *((u32 *)req->ptr + j)); - } + " %04X: %08X\n", j, + *((u32 *)req->ptr + j)); + } spin_unlock_irqrestore(udc->lock, flags); return n; @@ -1467,12 +1477,12 @@ static int _hardware_enqueue(struct ci13xxx_ep *mEp, struct ci13xxx_req *mReq) * At this point it's guaranteed exclusive access to qhead * (endpt is not primed) so it's no need to use tripwire */ - mEp->qh[mEp->dir].ptr->td.next = mReq->dma; /* TERMINATE = 0 */ - mEp->qh[mEp->dir].ptr->td.token &= ~TD_STATUS; /* clear status */ + mEp->qh.ptr->td.next = mReq->dma; /* TERMINATE = 0 */ + mEp->qh.ptr->td.token &= ~TD_STATUS; /* clear status */ if (mReq->req.zero == 0) - mEp->qh[mEp->dir].ptr->cap |= QH_ZLT; + mEp->qh.ptr->cap |= QH_ZLT; else - mEp->qh[mEp->dir].ptr->cap &= ~QH_ZLT; + mEp->qh.ptr->cap &= ~QH_ZLT; wmb(); /* synchronize before ep prime */ @@ -1542,11 +1552,11 @@ __acquires(mEp->lock) hw_ep_flush(mEp->num, mEp->dir); - while (!list_empty(&mEp->qh[mEp->dir].queue)) { + while (!list_empty(&mEp->qh.queue)) { /* pop oldest request */ struct ci13xxx_req *mReq = \ - list_entry(mEp->qh[mEp->dir].queue.next, + list_entry(mEp->qh.queue.next, struct ci13xxx_req, queue); list_del_init(&mReq->queue); mReq->req.status = -ESHUTDOWN; @@ -1571,8 +1581,6 @@ static int _gadget_stop_activity(struct usb_gadget *gadget) { struct usb_ep *ep; struct ci13xxx *udc = container_of(gadget, struct ci13xxx, gadget); - struct ci13xxx_ep *mEp = container_of(gadget->ep0, - struct ci13xxx_ep, ep); trace("%p", gadget); @@ -1583,7 +1591,8 @@ static int _gadget_stop_activity(struct usb_gadget *gadget) gadget_for_each_ep(ep, gadget) { usb_ep_fifo_flush(ep); } - usb_ep_fifo_flush(gadget->ep0); + usb_ep_fifo_flush(&udc->ep0out.ep); + usb_ep_fifo_flush(&udc->ep0in.ep); udc->driver->disconnect(gadget); @@ -1591,11 +1600,12 @@ static int _gadget_stop_activity(struct usb_gadget *gadget) gadget_for_each_ep(ep, gadget) { usb_ep_disable(ep); } - usb_ep_disable(gadget->ep0); + usb_ep_disable(&udc->ep0out.ep); + usb_ep_disable(&udc->ep0in.ep); - if (mEp->status != NULL) { - usb_ep_free_request(gadget->ep0, mEp->status); - mEp->status = NULL; + if (udc->status != NULL) { + usb_ep_free_request(&udc->ep0in.ep, udc->status); + udc->status = NULL; } return 0; @@ -1614,7 +1624,6 @@ static void isr_reset_handler(struct ci13xxx *udc) __releases(udc->lock) __acquires(udc->lock) { - struct ci13xxx_ep *mEp = &udc->ci13xxx_ep[0]; int retval; trace("%p", udc); @@ -1635,11 +1644,15 @@ __acquires(udc->lock) if (retval) goto done; - retval = usb_ep_enable(&mEp->ep, &ctrl_endpt_desc); + retval = usb_ep_enable(&udc->ep0out.ep, &ctrl_endpt_out_desc); + if (retval) + goto done; + + retval = usb_ep_enable(&udc->ep0in.ep, &ctrl_endpt_in_desc); if (!retval) { - mEp->status = usb_ep_alloc_request(&mEp->ep, GFP_ATOMIC); - if (mEp->status == NULL) { - usb_ep_disable(&mEp->ep); + udc->status = usb_ep_alloc_request(&udc->ep0in.ep, GFP_ATOMIC); + if (udc->status == NULL) { + usb_ep_disable(&udc->ep0out.ep); retval = -ENOMEM; } } @@ -1672,16 +1685,17 @@ static void isr_get_status_complete(struct usb_ep *ep, struct usb_request *req) /** * isr_get_status_response: get_status request response - * @ep: endpoint + * @udc: udc struct * @setup: setup request packet * * This function returns an error code */ -static int isr_get_status_response(struct ci13xxx_ep *mEp, +static int isr_get_status_response(struct ci13xxx *udc, struct usb_ctrlrequest *setup) __releases(mEp->lock) __acquires(mEp->lock) { + struct ci13xxx_ep *mEp = &udc->ep0in; struct usb_request *req = NULL; gfp_t gfp_flags = GFP_ATOMIC; int dir, num, retval; @@ -1736,27 +1750,23 @@ __acquires(mEp->lock) /** * isr_setup_status_phase: queues the status phase of a setup transation - * @mEp: endpoint + * @udc: udc struct * * This function returns an error code */ -static int isr_setup_status_phase(struct ci13xxx_ep *mEp) +static int isr_setup_status_phase(struct ci13xxx *udc) __releases(mEp->lock) __acquires(mEp->lock) { int retval; + struct ci13xxx_ep *mEp; - trace("%p", mEp); - - /* mEp is always valid & configured */ - - if (mEp->type == USB_ENDPOINT_XFER_CONTROL) - mEp->dir = (mEp->dir == TX) ? RX : TX; + trace("%p", udc); - mEp->status->no_interrupt = 1; + mEp = (udc->ep0_dir == TX) ? &udc->ep0out : &udc->ep0in; spin_unlock(mEp->lock); - retval = usb_ep_queue(&mEp->ep, mEp->status, GFP_ATOMIC); + retval = usb_ep_queue(&mEp->ep, udc->status, GFP_ATOMIC); spin_lock(mEp->lock); return retval; @@ -1778,11 +1788,11 @@ __acquires(mEp->lock) trace("%p", mEp); - if (list_empty(&mEp->qh[mEp->dir].queue)) + if (list_empty(&mEp->qh.queue)) return -EINVAL; /* pop oldest request */ - mReq = list_entry(mEp->qh[mEp->dir].queue.next, + mReq = list_entry(mEp->qh.queue.next, struct ci13xxx_req, queue); list_del_init(&mReq->queue); @@ -1794,10 +1804,10 @@ __acquires(mEp->lock) dbg_done(_usb_addr(mEp), mReq->ptr->token, retval); - if (!list_empty(&mEp->qh[mEp->dir].queue)) { + if (!list_empty(&mEp->qh.queue)) { struct ci13xxx_req* mReqEnq; - mReqEnq = list_entry(mEp->qh[mEp->dir].queue.next, + mReqEnq = list_entry(mEp->qh.queue.next, struct ci13xxx_req, queue); _hardware_enqueue(mEp, mReqEnq); } @@ -1836,16 +1846,14 @@ __acquires(udc->lock) int type, num, err = -EINVAL; struct usb_ctrlrequest req; - if (mEp->desc == NULL) continue; /* not configured */ - if ((mEp->dir == RX && hw_test_and_clear_complete(i)) || - (mEp->dir == TX && hw_test_and_clear_complete(i + 16))) { + if (hw_test_and_clear_complete(i)) { err = isr_tr_complete_low(mEp); if (mEp->type == USB_ENDPOINT_XFER_CONTROL) { if (err > 0) /* needs status phase */ - err = isr_setup_status_phase(mEp); + err = isr_setup_status_phase(udc); if (err < 0) { dbg_event(_usb_addr(mEp), "ERROR", err); @@ -1866,15 +1874,22 @@ __acquires(udc->lock) continue; } + /* + * Flush data and handshake transactions of previous + * setup packet. + */ + _ep_nuke(&udc->ep0out); + _ep_nuke(&udc->ep0in); + /* read_setup_packet */ do { hw_test_and_set_setup_guard(); - memcpy(&req, &mEp->qh[RX].ptr->setup, sizeof(req)); + memcpy(&req, &mEp->qh.ptr->setup, sizeof(req)); } while (!hw_test_and_clear_setup_guard()); type = req.bRequestType; - mEp->dir = (type & USB_DIR_IN) ? TX : RX; + udc->ep0_dir = (type & USB_DIR_IN) ? TX : RX; dbg_setup(_usb_addr(mEp), &req); @@ -1895,7 +1910,7 @@ __acquires(udc->lock) if (err) break; } - err = isr_setup_status_phase(mEp); + err = isr_setup_status_phase(udc); break; case USB_REQ_GET_STATUS: if (type != (USB_DIR_IN|USB_RECIP_DEVICE) && @@ -1905,7 +1920,7 @@ __acquires(udc->lock) if (le16_to_cpu(req.wLength) != 2 || le16_to_cpu(req.wValue) != 0) break; - err = isr_get_status_response(mEp, &req); + err = isr_get_status_response(udc, &req); break; case USB_REQ_SET_ADDRESS: if (type != (USB_DIR_OUT|USB_RECIP_DEVICE)) @@ -1916,7 +1931,7 @@ __acquires(udc->lock) err = hw_usb_set_address((u8)le16_to_cpu(req.wValue)); if (err) break; - err = isr_setup_status_phase(mEp); + err = isr_setup_status_phase(udc); break; case USB_REQ_SET_FEATURE: if (type != (USB_DIR_OUT|USB_RECIP_ENDPOINT) && @@ -1932,12 +1947,12 @@ __acquires(udc->lock) spin_lock(udc->lock); if (err) break; - err = isr_setup_status_phase(mEp); + err = isr_setup_status_phase(udc); break; default: delegate: if (req.wLength == 0) /* no data phase */ - mEp->dir = TX; + udc->ep0_dir = TX; spin_unlock(udc->lock); err = udc->driver->setup(&udc->gadget, &req); @@ -1968,7 +1983,7 @@ static int ep_enable(struct usb_ep *ep, const struct usb_endpoint_descriptor *desc) { struct ci13xxx_ep *mEp = container_of(ep, struct ci13xxx_ep, ep); - int direction, retval = 0; + int retval = 0; unsigned long flags; trace("%p, %p", ep, desc); @@ -1982,7 +1997,7 @@ static int ep_enable(struct usb_ep *ep, mEp->desc = desc; - if (!list_empty(&mEp->qh[mEp->dir].queue)) + if (!list_empty(&mEp->qh.queue)) warn("enabling a non-empty endpoint!"); mEp->dir = usb_endpoint_dir_in(desc) ? TX : RX; @@ -1991,29 +2006,22 @@ static int ep_enable(struct usb_ep *ep, mEp->ep.maxpacket = __constant_le16_to_cpu(desc->wMaxPacketSize); - direction = mEp->dir; - do { - dbg_event(_usb_addr(mEp), "ENABLE", 0); - - mEp->qh[mEp->dir].ptr->cap = 0; - - if (mEp->type == USB_ENDPOINT_XFER_CONTROL) - mEp->qh[mEp->dir].ptr->cap |= QH_IOS; - else if (mEp->type == USB_ENDPOINT_XFER_ISOC) - mEp->qh[mEp->dir].ptr->cap &= ~QH_MULT; - else - mEp->qh[mEp->dir].ptr->cap &= ~QH_ZLT; + dbg_event(_usb_addr(mEp), "ENABLE", 0); - mEp->qh[mEp->dir].ptr->cap |= - (mEp->ep.maxpacket << ffs_nr(QH_MAX_PKT)) & QH_MAX_PKT; - mEp->qh[mEp->dir].ptr->td.next |= TD_TERMINATE; /* needed? */ + mEp->qh.ptr->cap = 0; - retval |= hw_ep_enable(mEp->num, mEp->dir, mEp->type); + if (mEp->type == USB_ENDPOINT_XFER_CONTROL) + mEp->qh.ptr->cap |= QH_IOS; + else if (mEp->type == USB_ENDPOINT_XFER_ISOC) + mEp->qh.ptr->cap &= ~QH_MULT; + else + mEp->qh.ptr->cap &= ~QH_ZLT; - if (mEp->type == USB_ENDPOINT_XFER_CONTROL) - mEp->dir = (mEp->dir == TX) ? RX : TX; + mEp->qh.ptr->cap |= + (mEp->ep.maxpacket << ffs_nr(QH_MAX_PKT)) & QH_MAX_PKT; + mEp->qh.ptr->td.next |= TD_TERMINATE; /* needed? */ - } while (mEp->dir != direction); + retval |= hw_ep_enable(mEp->num, mEp->dir, mEp->type); spin_unlock_irqrestore(mEp->lock, flags); return retval; @@ -2146,7 +2154,7 @@ static int ep_queue(struct usb_ep *ep, struct usb_request *req, spin_lock_irqsave(mEp->lock, flags); if (mEp->type == USB_ENDPOINT_XFER_CONTROL && - !list_empty(&mEp->qh[mEp->dir].queue)) { + !list_empty(&mEp->qh.queue)) { _ep_nuke(mEp); retval = -EOVERFLOW; warn("endpoint ctrl %X nuked", _usb_addr(mEp)); @@ -2170,9 +2178,9 @@ static int ep_queue(struct usb_ep *ep, struct usb_request *req, /* push request */ mReq->req.status = -EINPROGRESS; mReq->req.actual = 0; - list_add_tail(&mReq->queue, &mEp->qh[mEp->dir].queue); + list_add_tail(&mReq->queue, &mEp->qh.queue); - if (list_is_singular(&mEp->qh[mEp->dir].queue)) + if (list_is_singular(&mEp->qh.queue)) retval = _hardware_enqueue(mEp, mReq); if (retval == -EALREADY) { @@ -2199,7 +2207,7 @@ static int ep_dequeue(struct usb_ep *ep, struct usb_request *req) trace("%p, %p", ep, req); if (ep == NULL || req == NULL || mEp->desc == NULL || - list_empty(&mReq->queue) || list_empty(&mEp->qh[mEp->dir].queue)) + list_empty(&mReq->queue) || list_empty(&mEp->qh.queue)) return -EINVAL; spin_lock_irqsave(mEp->lock, flags); @@ -2244,7 +2252,7 @@ static int ep_set_halt(struct usb_ep *ep, int value) #ifndef STALL_IN /* g_file_storage MS compliant but g_zero fails chapter 9 compliance */ if (value && mEp->type == USB_ENDPOINT_XFER_BULK && mEp->dir == TX && - !list_empty(&mEp->qh[mEp->dir].queue)) { + !list_empty(&mEp->qh.queue)) { spin_unlock_irqrestore(mEp->lock, flags); return -EAGAIN; } @@ -2355,7 +2363,7 @@ static int ci13xxx_vbus_session(struct usb_gadget *_gadget, int is_active) if (is_active) { pm_runtime_get_sync(&_gadget->dev); hw_device_reset(udc); - hw_device_state(udc->ci13xxx_ep[0].qh[RX].dma); + hw_device_state(udc->ep0out.qh.dma); } else { hw_device_state(0); if (udc->udc_driver->notify_event) @@ -2390,7 +2398,8 @@ int usb_gadget_probe_driver(struct usb_gadget_driver *driver, int (*bind)(struct usb_gadget *)) { struct ci13xxx *udc = _udc; - unsigned long i, k, flags; + unsigned long flags; + int i, j; int retval = -ENOMEM; trace("%p", driver); @@ -2430,41 +2439,43 @@ int usb_gadget_probe_driver(struct usb_gadget_driver *driver, udc->gadget.dev.driver = NULL; retval = 0; - for (i = 0; i < hw_ep_max; i++) { - struct ci13xxx_ep *mEp = &udc->ci13xxx_ep[i]; + for (i = 0; i < hw_ep_max/2; i++) { + for (j = RX; j <= TX; j++) { + int k = i + j * hw_ep_max/2; + struct ci13xxx_ep *mEp = &udc->ci13xxx_ep[k]; - scnprintf(mEp->name, sizeof(mEp->name), "ep%i", (int)i); + scnprintf(mEp->name, sizeof(mEp->name), "ep%i%s", i, + (j == TX) ? "in" : "out"); - mEp->lock = udc->lock; - mEp->device = &udc->gadget.dev; - mEp->td_pool = udc->td_pool; + mEp->lock = udc->lock; + mEp->device = &udc->gadget.dev; + mEp->td_pool = udc->td_pool; - mEp->ep.name = mEp->name; - mEp->ep.ops = &usb_ep_ops; - mEp->ep.maxpacket = CTRL_PAYLOAD_MAX; + mEp->ep.name = mEp->name; + mEp->ep.ops = &usb_ep_ops; + mEp->ep.maxpacket = CTRL_PAYLOAD_MAX; - /* this allocation cannot be random */ - for (k = RX; k <= TX; k++) { - INIT_LIST_HEAD(&mEp->qh[k].queue); + INIT_LIST_HEAD(&mEp->qh.queue); spin_unlock_irqrestore(udc->lock, flags); - mEp->qh[k].ptr = dma_pool_alloc(udc->qh_pool, - GFP_KERNEL, - &mEp->qh[k].dma); + mEp->qh.ptr = dma_pool_alloc(udc->qh_pool, GFP_KERNEL, + &mEp->qh.dma); spin_lock_irqsave(udc->lock, flags); - if (mEp->qh[k].ptr == NULL) + if (mEp->qh.ptr == NULL) retval = -ENOMEM; else - memset(mEp->qh[k].ptr, 0, - sizeof(*mEp->qh[k].ptr)); - } - if (i == 0) - udc->gadget.ep0 = &mEp->ep; - else + memset(mEp->qh.ptr, 0, sizeof(*mEp->qh.ptr)); + + /* skip ep0 out and in endpoints */ + if (i == 0) + continue; + list_add_tail(&mEp->ep.ep_list, &udc->gadget.ep_list); + } } if (retval) goto done; + udc->gadget.ep0 = &udc->ep0in.ep; /* bind gadget */ driver->driver.bus = NULL; udc->gadget.dev.driver = &driver->driver; @@ -2490,7 +2501,7 @@ int usb_gadget_probe_driver(struct usb_gadget_driver *driver, } } - retval = hw_device_state(udc->ci13xxx_ep[0].qh[RX].dma); + retval = hw_device_state(udc->ep0out.qh.dma); if (retval) pm_runtime_put_sync(&udc->gadget.dev); @@ -2508,7 +2519,7 @@ EXPORT_SYMBOL(usb_gadget_probe_driver); int usb_gadget_unregister_driver(struct usb_gadget_driver *driver) { struct ci13xxx *udc = _udc; - unsigned long i, k, flags; + unsigned long i, flags; trace("%p", driver); @@ -2544,17 +2555,14 @@ int usb_gadget_unregister_driver(struct usb_gadget_driver *driver) for (i = 0; i < hw_ep_max; i++) { struct ci13xxx_ep *mEp = &udc->ci13xxx_ep[i]; - if (i == 0) - udc->gadget.ep0 = NULL; - else if (!list_empty(&mEp->ep.ep_list)) + if (!list_empty(&mEp->ep.ep_list)) list_del_init(&mEp->ep.ep_list); - for (k = RX; k <= TX; k++) - if (mEp->qh[k].ptr != NULL) - dma_pool_free(udc->qh_pool, - mEp->qh[k].ptr, mEp->qh[k].dma); + if (mEp->qh.ptr != NULL) + dma_pool_free(udc->qh_pool, mEp->qh.ptr, mEp->qh.dma); } + udc->gadget.ep0 = NULL; udc->driver = NULL; spin_unlock_irqrestore(udc->lock, flags); diff --git a/drivers/usb/gadget/ci13xxx_udc.h b/drivers/usb/gadget/ci13xxx_udc.h index f61fed07f76b..a2492b65f98c 100644 --- a/drivers/usb/gadget/ci13xxx_udc.h +++ b/drivers/usb/gadget/ci13xxx_udc.h @@ -20,7 +20,7 @@ * DEFINE *****************************************************************************/ #define CI13XXX_PAGE_SIZE 4096ul /* page size for TD's */ -#define ENDPT_MAX (16) +#define ENDPT_MAX (32) #define CTRL_PAYLOAD_MAX (64) #define RX (0) /* similar to USB_DIR_OUT but can be used as an index */ #define TX (1) /* similar to USB_DIR_IN but can be used as an index */ @@ -88,8 +88,7 @@ struct ci13xxx_ep { struct list_head queue; struct ci13xxx_qh *ptr; dma_addr_t dma; - } qh[2]; - struct usb_request *status; + } qh; int wedge; /* global resources */ @@ -119,9 +118,13 @@ struct ci13xxx { struct dma_pool *qh_pool; /* DMA pool for queue heads */ struct dma_pool *td_pool; /* DMA pool for transfer descs */ + struct usb_request *status; /* ep0 status request */ struct usb_gadget gadget; /* USB slave device */ struct ci13xxx_ep ci13xxx_ep[ENDPT_MAX]; /* extended endpts */ + u32 ep0_dir; /* ep0 direction */ +#define ep0out ci13xxx_ep[0] +#define ep0in ci13xxx_ep[16] struct usb_gadget_driver *driver; /* 3rd party gadget driver */ struct ci13xxx_udc_driver *udc_driver; /* device controller driver */ -- cgit v1.2.1 From d14fc1a74e846d7851f24fc9519fe87dc12a1231 Mon Sep 17 00:00:00 2001 From: Libor Pechacek Date: Fri, 14 Jan 2011 14:30:21 +0100 Subject: USB: serial: handle Data Carrier Detect changes Alan's commit 335f8514f200e63d689113d29cb7253a5c282967 introduced .carrier_raised function in several drivers. That also means tty_port_block_til_ready can now suspend the process trying to open the serial port when Carrier Detect is low and put it into tty_port.open_wait queue. We need to wake up the process when Carrier Detect goes high and trigger TTY hangup when CD goes low. Some of the devices do not report modem status line changes, or at least we don't understand the status message, so for those we remove .carrier_raised again. Signed-off-by: Libor Pechacek Cc: stable Signed-off-by: Greg Kroah-Hartman --- drivers/usb/serial/ch341.c | 10 ++++++++++ drivers/usb/serial/cp210x.c | 13 +------------ drivers/usb/serial/digi_acceleport.c | 10 ---------- drivers/usb/serial/generic.c | 20 ++++++++++++++++++++ drivers/usb/serial/keyspan_pda.c | 17 ----------------- drivers/usb/serial/pl2303.c | 11 +++++++++++ drivers/usb/serial/spcp8x5.c | 6 +++++- include/linux/usb/serial.h | 3 +++ 8 files changed, 50 insertions(+), 40 deletions(-) diff --git a/drivers/usb/serial/ch341.c b/drivers/usb/serial/ch341.c index 63f7cc45bcac..7b8815ddf368 100644 --- a/drivers/usb/serial/ch341.c +++ b/drivers/usb/serial/ch341.c @@ -486,12 +486,22 @@ static void ch341_read_int_callback(struct urb *urb) if (actual_length >= 4) { struct ch341_private *priv = usb_get_serial_port_data(port); unsigned long flags; + u8 prev_line_status = priv->line_status; spin_lock_irqsave(&priv->lock, flags); priv->line_status = (~(data[2])) & CH341_BITS_MODEM_STAT; if ((data[1] & CH341_MULT_STAT)) priv->multi_status_change = 1; spin_unlock_irqrestore(&priv->lock, flags); + + if ((priv->line_status ^ prev_line_status) & CH341_BIT_DCD) { + struct tty_struct *tty = tty_port_tty_get(&port->port); + if (tty) + usb_serial_handle_dcd_change(port, tty, + priv->line_status & CH341_BIT_DCD); + tty_kref_put(tty); + } + wake_up_interruptible(&priv->delta_msr_wait); } diff --git a/drivers/usb/serial/cp210x.c b/drivers/usb/serial/cp210x.c index c3bea46e87fb..735ea03157ab 100644 --- a/drivers/usb/serial/cp210x.c +++ b/drivers/usb/serial/cp210x.c @@ -49,7 +49,6 @@ static int cp210x_tiocmset_port(struct usb_serial_port *port, struct file *, static void cp210x_break_ctl(struct tty_struct *, int); static int cp210x_startup(struct usb_serial *); static void cp210x_dtr_rts(struct usb_serial_port *p, int on); -static int cp210x_carrier_raised(struct usb_serial_port *p); static int debug; @@ -166,8 +165,7 @@ static struct usb_serial_driver cp210x_device = { .tiocmget = cp210x_tiocmget, .tiocmset = cp210x_tiocmset, .attach = cp210x_startup, - .dtr_rts = cp210x_dtr_rts, - .carrier_raised = cp210x_carrier_raised + .dtr_rts = cp210x_dtr_rts }; /* Config request types */ @@ -766,15 +764,6 @@ static int cp210x_tiocmget (struct tty_struct *tty, struct file *file) return result; } -static int cp210x_carrier_raised(struct usb_serial_port *p) -{ - unsigned int control; - cp210x_get_config(p, CP210X_GET_MDMSTS, &control, 1); - if (control & CONTROL_DCD) - return 1; - return 0; -} - static void cp210x_break_ctl (struct tty_struct *tty, int break_state) { struct usb_serial_port *port = tty->driver_data; diff --git a/drivers/usb/serial/digi_acceleport.c b/drivers/usb/serial/digi_acceleport.c index b92070c103cd..666e5a6edd82 100644 --- a/drivers/usb/serial/digi_acceleport.c +++ b/drivers/usb/serial/digi_acceleport.c @@ -455,7 +455,6 @@ static int digi_write_room(struct tty_struct *tty); static int digi_chars_in_buffer(struct tty_struct *tty); static int digi_open(struct tty_struct *tty, struct usb_serial_port *port); static void digi_close(struct usb_serial_port *port); -static int digi_carrier_raised(struct usb_serial_port *port); static void digi_dtr_rts(struct usb_serial_port *port, int on); static int digi_startup_device(struct usb_serial *serial); static int digi_startup(struct usb_serial *serial); @@ -511,7 +510,6 @@ static struct usb_serial_driver digi_acceleport_2_device = { .open = digi_open, .close = digi_close, .dtr_rts = digi_dtr_rts, - .carrier_raised = digi_carrier_raised, .write = digi_write, .write_room = digi_write_room, .write_bulk_callback = digi_write_bulk_callback, @@ -1339,14 +1337,6 @@ static void digi_dtr_rts(struct usb_serial_port *port, int on) digi_set_modem_signals(port, on * (TIOCM_DTR|TIOCM_RTS), 1); } -static int digi_carrier_raised(struct usb_serial_port *port) -{ - struct digi_port *priv = usb_get_serial_port_data(port); - if (priv->dp_modem_signals & TIOCM_CD) - return 1; - return 0; -} - static int digi_open(struct tty_struct *tty, struct usb_serial_port *port) { int ret; diff --git a/drivers/usb/serial/generic.c b/drivers/usb/serial/generic.c index e6833e216fc9..e4db5ad2bc55 100644 --- a/drivers/usb/serial/generic.c +++ b/drivers/usb/serial/generic.c @@ -479,6 +479,26 @@ int usb_serial_handle_break(struct usb_serial_port *port) } EXPORT_SYMBOL_GPL(usb_serial_handle_break); +/** + * usb_serial_handle_dcd_change - handle a change of carrier detect state + * @port: usb_serial_port structure for the open port + * @tty: tty_struct structure for the port + * @status: new carrier detect status, nonzero if active + */ +void usb_serial_handle_dcd_change(struct usb_serial_port *usb_port, + struct tty_struct *tty, unsigned int status) +{ + struct tty_port *port = &usb_port->port; + + dbg("%s - port %d, status %d", __func__, usb_port->number, status); + + if (status) + wake_up_interruptible(&port->open_wait); + else if (tty && !C_CLOCAL(tty)) + tty_hangup(tty); +} +EXPORT_SYMBOL_GPL(usb_serial_handle_dcd_change); + int usb_serial_generic_resume(struct usb_serial *serial) { struct usb_serial_port *port; diff --git a/drivers/usb/serial/keyspan_pda.c b/drivers/usb/serial/keyspan_pda.c index a10dd5676ccc..554a8693a463 100644 --- a/drivers/usb/serial/keyspan_pda.c +++ b/drivers/usb/serial/keyspan_pda.c @@ -679,22 +679,6 @@ static void keyspan_pda_dtr_rts(struct usb_serial_port *port, int on) } } -static int keyspan_pda_carrier_raised(struct usb_serial_port *port) -{ - struct usb_serial *serial = port->serial; - unsigned char modembits; - - /* If we can read the modem status and the DCD is low then - carrier is not raised yet */ - if (keyspan_pda_get_modem_info(serial, &modembits) >= 0) { - if (!(modembits & (1>>6))) - return 0; - } - /* Carrier raised, or we failed (eg disconnected) so - progress accordingly */ - return 1; -} - static int keyspan_pda_open(struct tty_struct *tty, struct usb_serial_port *port) @@ -881,7 +865,6 @@ static struct usb_serial_driver keyspan_pda_device = { .id_table = id_table_std, .num_ports = 1, .dtr_rts = keyspan_pda_dtr_rts, - .carrier_raised = keyspan_pda_carrier_raised, .open = keyspan_pda_open, .close = keyspan_pda_close, .write = keyspan_pda_write, diff --git a/drivers/usb/serial/pl2303.c b/drivers/usb/serial/pl2303.c index 45c40e6e9737..08c9181b8e48 100644 --- a/drivers/usb/serial/pl2303.c +++ b/drivers/usb/serial/pl2303.c @@ -678,9 +678,11 @@ static void pl2303_update_line_status(struct usb_serial_port *port, { struct pl2303_private *priv = usb_get_serial_port_data(port); + struct tty_struct *tty; unsigned long flags; u8 status_idx = UART_STATE; u8 length = UART_STATE + 1; + u8 prev_line_status; u16 idv, idp; idv = le16_to_cpu(port->serial->dev->descriptor.idVendor); @@ -702,11 +704,20 @@ static void pl2303_update_line_status(struct usb_serial_port *port, /* Save off the uart status for others to look at */ spin_lock_irqsave(&priv->lock, flags); + prev_line_status = priv->line_status; priv->line_status = data[status_idx]; spin_unlock_irqrestore(&priv->lock, flags); if (priv->line_status & UART_BREAK_ERROR) usb_serial_handle_break(port); wake_up_interruptible(&priv->delta_msr_wait); + + tty = tty_port_tty_get(&port->port); + if (!tty) + return; + if ((priv->line_status ^ prev_line_status) & UART_DCD) + usb_serial_handle_dcd_change(port, tty, + priv->line_status & UART_DCD); + tty_kref_put(tty); } static void pl2303_read_int_callback(struct urb *urb) diff --git a/drivers/usb/serial/spcp8x5.c b/drivers/usb/serial/spcp8x5.c index c7665d39d192..cbfb70bffdd0 100644 --- a/drivers/usb/serial/spcp8x5.c +++ b/drivers/usb/serial/spcp8x5.c @@ -133,7 +133,7 @@ struct spcp8x5_usb_ctrl_arg { /* how come ??? */ #define UART_STATE 0x08 -#define UART_STATE_TRANSIENT_MASK 0x74 +#define UART_STATE_TRANSIENT_MASK 0x75 #define UART_DCD 0x01 #define UART_DSR 0x02 #define UART_BREAK_ERROR 0x04 @@ -525,6 +525,10 @@ static void spcp8x5_process_read_urb(struct urb *urb) /* overrun is special, not associated with a char */ if (status & UART_OVERRUN_ERROR) tty_insert_flip_char(tty, 0, TTY_OVERRUN); + + if (status & UART_DCD) + usb_serial_handle_dcd_change(port, tty, + priv->line_status & MSR_STATUS_LINE_DCD); } tty_insert_flip_string_fixed_flag(tty, data, tty_flag, diff --git a/include/linux/usb/serial.h b/include/linux/usb/serial.h index 16d682f4f7c3..c9049139a7a5 100644 --- a/include/linux/usb/serial.h +++ b/include/linux/usb/serial.h @@ -347,6 +347,9 @@ extern int usb_serial_generic_prepare_write_buffer(struct usb_serial_port *port, extern int usb_serial_handle_sysrq_char(struct usb_serial_port *port, unsigned int ch); extern int usb_serial_handle_break(struct usb_serial_port *port); +extern void usb_serial_handle_dcd_change(struct usb_serial_port *usb_port, + struct tty_struct *tty, + unsigned int status); extern int usb_serial_bus_register(struct usb_serial_driver *device); -- cgit v1.2.1 From 3c47eb06f08eb970ea9d696bcdb57a175d37b470 Mon Sep 17 00:00:00 2001 From: Maulik Mankad Date: Thu, 13 Jan 2011 18:19:56 +0530 Subject: usb: gadget: composite: avoid access beyond array max length One of the USB CV MSC tests issues Get Max LUN request with invalid wIndex (wIndex = 65535) parameter. Add proper handling to prevent array index out of bounds issue. Signed-off-by: Maulik Mankad Cc: David Brownell Acked-by: Alan Stern Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/composite.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/usb/gadget/composite.c b/drivers/usb/gadget/composite.c index f6ff8456d52d..1ba4befe336b 100644 --- a/drivers/usb/gadget/composite.c +++ b/drivers/usb/gadget/composite.c @@ -928,8 +928,9 @@ unknown: */ switch (ctrl->bRequestType & USB_RECIP_MASK) { case USB_RECIP_INTERFACE: - if (cdev->config) - f = cdev->config->interface[intf]; + if (!cdev->config || w_index >= MAX_CONFIG_INTERFACES) + break; + f = cdev->config->interface[intf]; break; case USB_RECIP_ENDPOINT: -- cgit v1.2.1