summaryrefslogtreecommitdiffstats
path: root/sound/soc/codecs/tlv320dac33.c
Commit message (Collapse)AuthorAgeFilesLines
* ASoC: tlv320dac33: Internal clocking changesPeter Ujfalusi2010-03-191-2/+2
| | | | | | | | | | | | | | | During validation of the internal clocking setup it has been found that the following settings were not configured in an optimal way: ASRC_CTRL_A: SRCLKDIV was incorrect, instad of divide ratio 3, ratio of 2 has to be used (as the comment stated) DAC_CTRL_A: Fs = Fsref is the desired configuration instead of Fs = Fsref / 1.5 Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: tlv320dac33: Fix DSP modesPeter Ujfalusi2010-03-191-5/+1
| | | | | | | | | | To make DSP_A mode working correctly the data delay should be configured to 0. DSP_B mode thus can not be used with DAC33, so remove it. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: tlv320dac33: Correct the OSCSET calculationPeter Ujfalusi2010-02-161-1/+1
| | | | | | | | | | | OSCSET calculation was not correct in case of 44.1KHz sampling rate. With small adjustment both 48 and 44.1 KHz calculation now gives the correct value. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: tlv320dac33: Clearing FIFOFLUSH flag before playbackPeter Ujfalusi2010-02-161-0/+3
| | | | | | | | | | In repeated playback the FIFOFLUSH bit remained set, and never has been cleared. Clear it during the setup phase. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: tlv320dac33: Burst mode BCLK divider configurationPeter Ujfalusi2010-01-201-2/+13
| | | | | | | | | | | | | Add possibility to configure the burst mode BCLK divider through platform data structure. The BCLK divider changes the actual speed of the serial bus in burst mode, which is faster than the sampling frequency of the running stream. In this way platforms can experiment with the optimal burst speed without the need to modify the codec driver itself. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: tlv320dac33: BCLK divider fixPeter Ujfalusi2010-01-201-5/+6
| | | | | | | | | | | The BCLK divider was not configured in case of mode7. This leads to unpredictable behavior when switching between FIFO modes. Configure the BCLK divider depending on the fifo_mode (FIFO is in use, or FIFO bypass). Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: tlv320dac33: Correct the prefill number of samplesPeter Ujfalusi2010-01-191-1/+1
| | | | | | | | | | | Set the prefill number of samples as the same as the lower threshold in mode7. In this way the codec will read the same amount of data on startup and during the running playback. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: Add missing __devexit and __devinit annotationsMark Brown2010-01-121-3/+3
| | | | Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: tlv320dac33: Safety check for codec slave modePeter Ujfalusi2009-12-311-1/+6
| | | | | | | | | | The currently available FIFO modes (mode1 and mode7) require master mode from the codec. Do not allow the slave configuration when the FIFO is in use. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: tlv320dac33: Add new FIFO mode: mode 7Peter Ujfalusi2009-12-311-1/+34
| | | | | | | | | | | | | | | | | | | | | | | | Mode 7 of tlv320dac33 operates in the following way: The codec is in master mode. Host configures upper and lower thresholds in tlv320dac33 During playback the codec will clock in the data until the upper threshold is reached in FIFO. At this point the codec stops the colocks on the serial bus. When the FIFO fill is reaching the lower threshold limit the codec will enable the clocks on the serial bus, and clocks in data till the upper threshold is reached. In this mode, we can also request interrupts for threshold events (upper, lower and alarm), which could be used for power management. At this point the interrupts are not enabled for this mode, but it can be taken into use in the future, when the surrounding code makes it possible to use it. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.oc.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: tlv320dac33: Clean up the hardware configuration codePeter Ujfalusi2009-12-311-16/+45
| | | | | | | | | | | Use switch instead of if statements to configure FIFO bypass and mode1. With this change adding new FIFO mode is going to be easier, and cleaner. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: tlv320dac33: Introduce prefill and playback state handlersPeter Ujfalusi2009-12-311-6/+40
| | | | | | | | | | | Ensure that the code is going to be readable, when new FIFO modes are introduced later. Move the prefill and playback state handling to inlined functions. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: tlv320dac33: Change nsample switch to FIFO mode enumPeter Ujfalusi2009-12-311-17/+32
| | | | | | | | | | In order to have support for more FIFO modes supported by tlv320dac33, the switch for enabling/disabling the FIFO use has to be replaced with an enum. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: tlv320dac33: Add support for regulator frameworkIlkka Koskinen2009-12-041-13/+79
| | | | | | | | | Take the regulator framework in use for managing the power sources. Signed-off-by: Ilkka Koskinen <ilkka.koskinen@nokia.com> Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: tlv320dac33: Change RT wq to singlethread wqPeter Ujfalusi2009-11-261-1/+2
| | | | | | | | | RT workqueue is going away in the near future, replace it with singlethread wq for now, which is still supported. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Acked-by: Liam Girdwood <lrg@slimlogic.co.uk> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: Remove redundant snd_soc_dapm_new_widgets() callsMark Brown2009-11-121-1/+0
| | | | | | | The DAPM widgets are now insntantiated by the core when creating the card so there is no need for the individual CODEC drivers to do so. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: Factor out snd_soc_init_card()Mark Brown2009-11-031-9/+1
| | | | | | | | | snd_soc_init_card() is always called as the last part of the CODEC probe function so we can factor it out into the core card setup rather than have each CODEC replicate the code to do the initialiastation. This will be required to support multiple CODECs per card. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* ASoC: Codec driver for Texas Instruments tlv320dac33 codecPeter Ujfalusi2009-10-151-0/+1237
Driver for Texas Instruments TLV320DAC33 (SLAS546) low power stereo audio DAC. TLV320DAC33 is a stereo audio codec with integrated 24KB FIFO for low power audio playback. The digital interface can use I2S, DSP (A or B), Right and Left justified formats. DAC33 has stereo analog input, which can be bypassed to the analog outputs. Regarding to the internal 24KB FIFO the driver implements 'FIFO bypass' mode (default) and nSample mode (FIFO is in use). a) In 'FIFO bypass' mode the internal FIFO is not in use, the codec is working synchronously as a normal codec (it needs constant stream of data on the digital interface). b) The nSample mode implementation uses one interrupt line from DAC33 to the host: Alarm threshold is set to 10ms of audio data (limit by the driver implementation). DAC33 will signal an interrupt, when the FIFO level goes under the Alarm threshold. The host will write to nSample register a value (number of stereo samples), to tell DAC33 how many samples it should read in a burst from the host. When the DAC33 received the number of samples, it disables the clocks on the I2S bus. When the FIFO use again goes under the Alarm threshold, DAC33 signals the host with an interrupt, and the process is repeated. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
OpenPOWER on IntegriCloud