| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
As bi_end_io is only called once when the reqeust is complete,
the 'size' argument is now redundant. Remove it.
Now there is no need for bio_endio to subtract the size completed
from bi_size. So don't do that either.
While we are at it, change bi_end_io to return void.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
| |
|
|
|
|
|
|
|
| |
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
There is a small problem in handling page bounce.
At the moment blk_max_pfn equals max_pfn, which is in fact not maximum
possible _number_ of a page frame, but the _amount_ of page frames. For
example for the 32bit x86 node with 4Gb RAM, max_pfn = 0x100000, but not
0xFFFF.
request_queue structure has a member q->bounce_pfn and queue needs bounce
pages for the pages _above_ this limit. This routine is handled by
blk_queue_bounce(), where the following check is produced:
if (q->bounce_pfn >= blk_max_pfn)
return;
Assume, that a driver has set q->bounce_pfn to 0xFFFF, but blk_max_pfn
equals 0x10000. In such situation the check above fails and for each bio
we always fall down for iterating over pages tied to the bio.
I want to notice, that for quite a big range of device drivers (ide, md,
...) such problem doesn't happen because they use BLK_BOUNCE_ANY for
bounce_pfn. BLK_BOUNCE_ANY is defined as blk_max_pfn << PAGE_SHIFT, and
then the check above doesn't fail. But for other drivers, which obtain
reuired value from drivers, it fails. For example sata_nv uses
ATA_DMA_MASK or dev->dma_mask.
I propose to use (max_pfn - 1) for blk_max_pfn. And the same for
blk_max_low_pfn. The patch also cleanses some checks related with
bounce_pfn.
Signed-off-by: Vasily Tarasov <vtaras@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
Currently we issue a bounce trace when __blk_queue_bounce() is called,
but that merely means that the device has a lower dma mask than the
higher pages in the system. The bio itself may still be lower pages. So
move the bounce trace into __blk_queue_bounce(), when we know there will
actually be page bouncing.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
|
Move the bounce buffer code from mm/highmem.c to mm/bounce.c so that it can be
more easily disabled when the block layer is disabled.
!!!NOTE!!! There may be a bug in this code: Should init_emergency_pool() be
contingent on CONFIG_HIGHMEM?
Signed-Off-By: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
