| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
* Convert GPIO and IRQ handling to use the <asm/gpio.h> api.
* Perform the reset only after the power button has been held down
for at least two seconds. Do the reset on the release of the power
button, so that NAS devices which have been set to auto-power-on (by
solder bridging the power button) do not continuously power cycle.
* Remove all superflous constants from nas100d.h
* Add LED constants to nas100d.h while we're there.
* Update the board LED setup code to use those constants.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
|
|
|
|
|
|
|
|
| |
This trivial patch updates the nslu2 and nas-100d headers to
remove pointless GPIO defines, and updates nslu2-setup.c
accordingly. In addition minor style cleanups to some comments
are included.
Signed-off-by: Michael-Luke Jones <mlj28@cam.ac.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Patch from Alessandro Zummo
The I2C pin assignment for the Iomega NAS100d board was incorrect. This
patch fixes it. The correct assignment has now been tested using the
new RTC class and a new driver for the RTC on the NAS100d.
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Patch from Deepak Saxena
The expansion bus on the IXP46x NPU can be configured for either 32MiB or
16MiB windows and changing the configuration causes the base address for
each chip select for each region to change. Because of this, we cannot
hardcode the physical base as we currently do. This patch checks the
expansion bus configuration registers at runtime to determine the
appropriate window size. Note that this requires that the bootloader
already configured the device sizes appropriately, but I feel that is
valid assumption to make as the bootloader must configure and access
the flash window, the output display (LCD, LEDs, etc) window, and
other expansion bus devices.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
|
Patch from Rod Whitby
This patch adds support for a new arm/ixp4xx machine - the Iomega NAS 100d network attached storage product. The NAS100D is a consumer device containing a 266MHz Intel IXP420 processor, 16MB of flash, 64MB of RAM, a 160Gb internal IDE hard disk, and 802.11b/g wireless on an Atheros mini-PCI card.
Work on porting the latest 2.6.x kernel to this device is being done by
the NSLU2-Linux project (the same team who maintains the port to the
Linksys NSLU2 device). In particular, the majority of this patch was
authored by Alessandro Zummo, based on the work done for MACH_NSLU2
support by the NSLU2-Linux core team of developers.
MACH_NAS100D (as implemented by this patch) can be enabled in jumbo
ixp4xx kernels without any affect on the other machines supported by
that kernel.
This patch applies cleanly against 2.6.15-rc7 and should be trivial to
apply to later kernel versions. It does not depend upon any other
patches.
Modified files (and number of lines inserted):
arch/arm/mach-ixp4xx/Kconfig | 8
arch/arm/mach-ixp4xx/Makefile | 1
include/asm-arm/arch-ixp4xx/hardware.h | 1
include/asm-arm/arch-ixp4xx/irqs.h | 9
include/asm-arm/arch-ixp4xx/nas100d.h | 75
arch/arm/mach-ixp4xx/nas100d-pci.c | 77
arch/arm/mach-ixp4xx/nas100d-power.c | 69
arch/arm/mach-ixp4xx/nas100d-setup.c | 133
-- Rod Whitby (NSLU2-Linux project lead)
Signed-off-by: Rod Whitby <rod@whitby.id.au>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
