summaryrefslogtreecommitdiffstats
path: root/drivers/usb/host/ehci.h
Commit message (Collapse)AuthorAgeFilesLines
* usb: ehci should use u16 for isochronous intervalsDavid Brownell2008-02-011-1/+1
| | | | | | | | | | | | | | | | | | While most isochronous endpoints have short polling intervals, the EHCI driver won't necessarily handle larger ones correctly. This patch switches to use a "u16" to represent those periods, not a u8, since it can always work: the largest expressible period is 2^15 units ... not the previous too-short limit of 128 frames (full or low speeds) or microframes (high speed, 32 frames). This bug is essentially theoretical, since the few ISO endpoints I've seen which don't use one transfer per frame are high speed ones using more than that (including high bandwidth, 24 KB/msec). Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: ehci saves some memory in ISO transfer descriptorsKarsten Wiese2008-02-011-1/+0
| | | | | | | | | | | | | | | | In the EHCI driver, itd->usecs[8] is used in periodic_usecs(), indexed by uframe. For an ITD's unused uframes it is 0, else it contains the same value as itd->stream->usecs. To check if an ITD's uframe is used, we can instead test itd->hw_transaction[uframe]: if used, it will be nonzero no matter what endianess is used. This patch replaces those two uses, eliminates itd->usecs[], and saves eight bytes from each ITD. Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: add ehci-ixp bus glueVladimir Barinov2008-02-011-0/+5
| | | | | | | | | EHCI Glue driver for Intel IXP4XX EHCI USB controller Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: add ehci-ppc-of bus glue (device-tree aware)Valentine Barshak2008-02-011-1/+1
| | | | | | | | | | | | | This adds device-tree-aware ehci-ppc-of driver. The code is based on the ehci-ppc-soc driver by Stefan Roese <sr@denx.de>. Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI: add separate IAA watchdog timerAlan Stern2008-02-011-7/+15
| | | | | | | | | | | | | | | | This patch (as1028) was mostly written by David Brownell; I made only a few changes (extra log info and a small bug fix -- which might account for why David's version had to be reverted). It adds a new watchdog timer to the ehci-hcd driver to be used exclusively for detecting lost or missing IAA notifications. Previously a shared timer had been used, which may have led to some problems as reported by Christian Hoffmann. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: convert ehci debug files to use debugfs instead of sysfsTony Jones2008-02-011-0/+8
| | | | | | | | | | | We should not have multiple line files in sysfs, this moves the data to debugfs instead, like the UHCI driver. Signed-off-by: Tony Jones <tonyj@suse.de> Cc: Kay Sievers <kay.sievers@vrfy.org> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* Revert "USB: EHCI cpufreq fix"Linus Torvalds2007-08-201-14/+0
| | | | | | | | | | | | | This reverts commit 196705c9bbc03540429b0f7cf9ee35c2f928a534. It was reported to cause a regression by Daniel Exner, and Arjan van de Ven points out that we actually already have infrastructure in place for setting limits on acceptable DMA latency that would be the much more correct fix for the problem with some Broadcom EHCI controllers. Fixed up trivial conflicts due to the changes to support big-endian host controller descriptors in drivers/usb/host/{ehci-sched.c,ehci.h}. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* USB: EHCI: Safe endianness for transfer buffers after reset in case of HUB ↵Vladimir Barinov2007-07-121-0/+6
| | | | | | | | | | | | | | with TT This patch fixes the endianness select for transfer buffers in EHCI controllers that have Transaction Translator built in the hub. Also I cleaned it up to make rid of magic numbers. Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com> Cc: <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI, OHCI: handover changesAlan Stern2007-07-121-0/+3
| | | | | | | | | | | | | | | | | | | This patch (as887) changes the way ehci-hcd and ohci-hcd handle a loss of VBUS power during suspend. In order for the USB-persist facility to work correctly, it is necessary for low- and full-speed devices attached to a high-speed port to be handed back to the companion controller during resume processing. This entails three changes: adding code to ehci-hcd to perform the handover, removing code from ohci-hcd to turn off ports during root-hub reinit, and adding code to ohci-hcd to turn on ports during PCI controller resume. (Other bus glue resume methods for platforms supporting high-speed controllers would need a similar change, if any existed.) Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: ehci refcounts work on ppc7448David Brownell2007-07-121-1/+8
| | | | | | | | | | | | Remove atomic operations on the reference counter for EHCI queue heads. On various platforms (including ppc7448), atomic operations are unusable with dma-coherent memory. Signed-off-by: Steven J. Hill <sjhill1@rockwellcollins.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI support for big-endian descriptorsStefan Roese2007-07-121-52/+153
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch implements supports for EHCI controllers whose in-memory data structures are represented in big-endian format. This is needed (unfortunately) for the AMCC PPC440EPx SoC EHCI controller; the EHCI spec doesn't specify little-endian format, although that's what most other implementations use. The guts of the patch are to introduce the hc32 type and change all references from le32 to hc32. All access routines are converted from cpu_to_le32(...) to cpu_to_hc32(ehci, ...) and similar for the other "direction". (This is the same approach used with OHCI.) David fixed: Whitespace fixes; refresh against ehci cpufreq patch; move glue for that PPC driver to the patch adding it; fix free symbol capture bugs in modified "constant" macros; and make "hc32" etc be "le32" unless we really need the BE options, so "sparse" can do some real good. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI cpufreq fixStuart_Hayes@Dell.com2007-07-121-0/+11
| | | | | | | | | | | | | | | | | EHCI controllers that don't cache enough microframes can get MMF errors when CPU frequency changes occur between the start and completion of split interrupt transactions, due to delays in reading main memory (caused by CPU cache snoop delays). This patch adds a cpufreq notifier to the EHCI driver that will inactivate split interrupt transactions during frequency transitions. It was tested on Intel ICH7 and Serverworks/Broadcom HT1000 EHCI controllers. Signed-off-by: Stuart Hayes <stuart_hayes@dell.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [PATCH] hci_{read,write}l() does force casts to wrong type for no reasonAl Viro2007-02-091-6/+6
| | | | | | | readl() et.al. expect iomem pointer, so WTF force-cast it to normal one??? Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* EHCI: force high-speed devices to run at full speedAlan Stern2007-02-071-1/+5
| | | | | | | | | | | | | | | | | | | | This patch (as710) adds a sysfs class-device attribute file named "companion" for EHCI controllers. The file contains a list of port numbers that are dedicated to the companion controller; by writing a port number to the file the user can force a high-speed device attached directly to the computer to run at full speed. (As far as I know it is not possible to do this for a device attached to an external hub.) A port is removed from the file by writing the negative of its port number. Several users have asked for this facility and it seems like a useful thing to have. Every now and then one runs across a device which behaves much better at full speed than at high speed. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: Fix EHCI warningBenjamin Herrenschmidt2007-02-071-0/+8
| | | | | | | | | | This patch fixes a warning introduced by the big endian MMIO EHCI support patch on platforms that don't have readl_be/writel_be variants (though mostly harmless as those are called in an if (0) statement, but gcc still warns). Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* USB: Implement support for EHCI with big endian MMIOBenjamin Herrenschmidt2007-02-071-0/+32
| | | | | | | | | | | | | | | | | | This patch implements supports for EHCI controllers whose MMIO registers are big endian and enables that functionality for the Toshiba SCC chip. It does _not_ add support for big endian in-memory data structures as this is not needed for that chip and I hope it will never be. The guts of the patch are to convert readl(...) to ehci_readl(ehci, ...) and similarly for register writes. Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Geoff Levand <geoffrey.levand@am.sony.com> Acked-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* EHCI: Fix root-hub and port suspend/resume problemsAlan Stern2006-12-011-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch (as738b) fixes numerous problems in the controller/root-hub suspend/resume/remote-wakeup support in ehci-hcd: The bus_resume() routine should wake up only the ports that were suspended by bus_suspend(). Ports that were already suspended should remain that way. The interrupt mask is used to detect loss of power in the bus_resume() routine (if the mask is 0 then power was lost). However bus_suspend() always sets the mask to 0. Instead the mask should retain its normal value, with port-change-detect interrupts disabled if remote wakeup is turned off. The interrupt mask should be reset to its correct value at the end of bus_resume() regardless of whether power was lost. bus_resume() reinitializes the operational registers if power was lost. However those registers are not in the aux power well, hence they can lose their values whenever the controller is put into D3. They should always be reinitialized. When a port-change interrupt occurs and the root hub is suspended, the interrupt handler should request a root-hub resume instead of starting up the controller all by itself. There's no need for the interrupt handler to request a root-hub resume every time a suspended port sends a remote-wakeup request. The pci_resume() method doesn't need to check for connected ports when deciding whether or not to reset the controller. It can make that decision based on whether Vaux power was maintained. Even when the controller does not need to be reset, pci_resume() must undo the effect of pci_suspend() by re-enabling the interrupt mask. If power was lost, pci_resume() must not call ehci_run(). At this point the root hub is still supposed to be suspended, not running. It's enough to rewrite the command register and set the configured_flag. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: revert EHCI VIA workaround patchGreg Kroah-Hartman2006-10-171-15/+7
| | | | | | | | This reverts 26f953fd884ea4879585287917f855c63c6b2666 which caused resume problems on the mac mini. Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI update VIA workaroundDavid Brownell2006-09-271-7/+15
| | | | | | | | | | | | | | This revamps handling of the hardware "async advance" IRQ, and its watchdog timer. Basically it dis-entangles that important timeout from the others, simplifying the associated state and code to make it more robust. This reportedly improves behavior of EHCI on some systems with VIA chips, and AFAIK won't affect non-VIA hardware. VIA systems need this code to recover from silcon bugs whereby the "async advance" IRQ isn't issued. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: EHCI whitespace fixes (cosmetic)David Brownell2006-09-271-18/+18
| | | | | | | | | | [ ... when you have an editor set to remind you of whitespace bugs ... ] Cosmetic EHCI changes: remove end-of-line whitespace, spaces before tabs. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* USB: Properly unregister reboot notifier in case of failure in ehci hcdAleksey Gorelov2006-09-271-1/+0
| | | | | | | | | | | | | | | | | | | | | | If some problem occurs during ehci startup, for instance, request_irq fails, echi hcd driver tries it best to cleanup, but fails to unregister reboot notifier, which in turn leads to crash on reboot/poweroff. The following patch resolves this problem by not using reboot notifiers anymore, but instead making ehci/ohci driver get its own shutdown method. For PCI, it is done through pci glue, for everything else through platform driver glue. One downside: sa1111 does not use platform driver stuff, and does not have its own shutdown hook, so no 'shutdown' is called for it now. I'm not sure if it is really necessary on that platform, though. Signed-off-by: Aleks Gorelov <dared1st@yahoo.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [PATCH] USB: EHCI and Freescale 83xx quirkKumar Gala2006-03-201-0/+15
| | | | | | | | | | | On the MPC834x processors the multiport host (MPH) EHCI controller has an erratum in which the port number in the queue head expects to be 0..N-1 instead of 1..N. If we are on one of these chips we subtract one from the port number before putting it into the queue head. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [PATCH] USB: EHCI and NF2 quirkDavid Brownell2006-03-201-1/+2
| | | | | | | | | | | | | | | | | | This teaches the EHCI driver about a quirk seen in older NForce2 chips, adding a workaround to ignore selective suspend requests. Bus-wide (so-called "global") suspend still works, as does USB wakeup of a root hub that's globally suspended. There's still a hole in this support though. Strictly speaking, this should _fail_ selective suspend requests, rather than ignoring them, since doing it this way means that devices which should be able to issue remote wakeup are not going to be able to do that. For now, we'll just live with that problem ... since usbcore expects to do selective suspend on the way towards a full bus suspend, and usbcore needs to be able to do full bus suspend. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [PATCH] EHCI, split out PCI glueMatt Porter2005-10-281-0/+1
| | | | | | | | | | | | | | | This splits BIOS and PCI specific support out of ehci-hcd.c into ehci-pci.c. It follows the model already used in the OHCI driver so support for non-PCI EHCI controllers can be more easily added. Signed-off-by: Matt Porter <mporter@kernel.crashing.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> drivers/usb/host/ehci-hcd.c | 543 ++++++-------------------------------------- drivers/usb/host/ehci-pci.c | 414 +++++++++++++++++++++++++++++++++ drivers/usb/host/ehci.h | 1 3 files changed, 492 insertions(+), 466 deletions(-)
* [PATCH] USB: EHCI port tweaksDavid Brownell2005-09-121-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | One change may improve some S1 or S3 resume cases, and the other seems mostly to explain some strange state "lsusb" would show. Two fixes: - On resume, don't think about resuming any unpowered port, or resetting any port with OWNER set to the OHCI/UHCI companion. This will make some S1 and S3 resume scenarios work better. - PORT_CSC was not being cleared correctly in ehci_hub_status_data. This was visible at least through current versions of "lsusb", and might have caused some other hub related strangeness. The fix addresses all three write-to-clear bits, using the same approach that UHCI happens to use: a mask of bits that are cleared in most writes to that port status register. Original patch seems to have been from from William.Morrow@amd.com and this version (from David) finishes the write-to-clear changes. Signed-off-by: Jordan Crouse <jordan.crouse@amd.com> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [PATCH] ehci: add tt_usecsdavid-b@pacbell.net2005-09-081-0/+2
| | | | | | | | | | | | This adds the field tt_usecs to ehci_qh and ehci_iso_stream, and sets it appropriately when setting them up as periodic endpoints. It records the transation translator's think_time (added in last patch) plus the downstream (i.e. low or full speed) bustime of the transfer associated with each interrupt or iso frame, as calculated by usb_calc_bus_time. Signed-off-by: Dan Streetman <ddstreet@ieee.org> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [PATCH] USB: ehci: microframe handling fixDavid Brownell2005-08-041-0/+5
| | | | | | | | | | | | | | | | | | | | | | This patch has a one line oops fix, plus related cleanups. - The bugfix uses microframe scheduling data given to the hardware to test "is this a periodic QH", rather than testing for nonzero period. (Prevents an oops by providing the correct answer.) - The cleanup going along with the patch should make it clearer what's going on whenever those bitfields are accessed. The bug came about when, around January, two new kinds of EHCI interrupt scheduling operation were added, involving both the high speed (24 KBytes per millisec) and low/full speed (1-64 bytes per millisec) microframe scheduling. A driver for the Edirol UA-1000 Audio Capture Unit ran into the oops; it used one of the newly supported high speed modes. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* [PATCH] USB: ehci power fixesDavid Brownell2005-05-031-9/+10
| | | | | | | | | | | | | | | | | | Miscellaneous updates for EHCI. - Mostly updates the power switching on EHCI controllers. One routine centralizes the "power on/off all ports" logic, and the capability to do that is reported more correctly. - Courtesy Colin Leroy, a patch to always power up ports after resumes which didn't keep a USB device suspended. The reset-everything logic powers down those ports (on some hardware) so something needs to turn them back on. - Minor tweaks/bugfixes for the debug port support. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* [PATCH] USB: hcd suspend uses pm_message_tDavid Brownell2005-04-181-1/+1
| | | | | | | | | | | | | | | | This patch includes minor "sparse -Wbitwise" updates for the PCI based HCDs. Almost all of them involve just changing the second parameter of the suspend() method to a pm_message_t ... the others relate to how the EHCI code walks in-memory data structures. (There's a minor bug fixed there too ... affecting the big-endian sysfs async schedule dump.) Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Index: gregkh-2.6/drivers/usb/core/hcd.h ===================================================================
* Linux-2.6.12-rc2v2.6.12-rc2Linus Torvalds2005-04-161-0/+637
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
OpenPOWER on IntegriCloud